Hunter Fan 45065-01 Fan User Manual
Contents
1. P IS Owner s Guide and Installation Manual For reference also attach your receipt or a copy of your receipt to the manual Warrenty Assistonre Type 2 Mode SINCE 1886 Form 45065 01 200 2009 Hunter Fan Co Welcome Your new Hunter ceiling fan is an addition to your home or office that will provide comfort and performance for many years This installation and operation manual gives you complete instructions for installing and operating your fan We are proud of our work We appreciate the opportunity to supply you with the best ceiling fan available anywhere in the world Before installing your fan for your records and warranty assistance record information from the carton and Hunter nameplate label located on the top of the fan motor housing Cautions and Warnings e READ THIS ENTIRE MANUAL CAREFULLY BEFORE BEGINNING INSTALLATION SAVE THESE INSTRUCTIONS e Use only Hunter replacement parts Preparing the Fan Site e To reduce the risk of personal injury attach the fan directly to the 1 Getting Ready support structure of the building according to these instructions and use only the hardware supplied To avoid possible electrical shock before installing your fan disconnect the power by turning off the circuit breakers to the 4 Wiring the Fan outlet box and associated wall switch location If you cannot lock 5 Installing the Canopy and Canopy the circuit breakers in the off posit2. Partially install two canopy screws about 2 full turns in the hanger bracket Raise the canopy over the hanger bracket Align partially installed screws with key slots in canopy Twist canopy clockwise to secure Install third amp fourth canopy screw in round hole on canopy Securely tighten all four screws Using both hands push the canopy trim ring up to the top of the canopy Twist canopy trim ring clockwise to secure the canopy Should you need to remove the canopy trim ring follow these steps 1 Twist canopy trim ring counter clockwise until it releases from canopy Step 5 5 lI Steps 5 1 5 2 Hanger Bracket f gt Canopy Trim 7 Ring Step 5 4 45065 01 11 05 09 Hunter Fan Company 6 Assembling the Blades Hunter fans use several styles of fan blade irons brackets that hold the blade to the fan 6 1 Your fan may include blade grommets If your fan has grommets Step 6 1 Detail insert them by hand into the holes on the blades 6 2 Attach each blade to a blade iron using three blade assembly screws If you used grommets the blades may appear slightly loose after screws are tightened This is normal 6 3 Remove the blade mounting screws and rubber shipping bumpers from the motor Note Some blade mounting screws are installed in the motor to secure shipping blocks 6 4 For each blade insert one blade mounting scre
3. Uninstalling the Light Fixture 7 14 To uninstall the light fixture first disconnect the plug connectors between the black wire and the Black White wire Disconnect the plug connectors between the two white wires Remove the two screws attaching the light kit to the lower switch housing Remove the light fixture from the lower switch housing pulling Lower Swich disconnected wires through the hole in the center of the lower z Housing switch housing Note When removing the wires pull the thin plug connector male through first and then pull the other plug connector female through the hole Install the dummy terminals included in the sack parts on the two disconnected wires in the lower switch housing Install the switch housing cap and plug button to the lower switch housing Once you have uninstalled the light fixture continue with step 7 6 Male Dummy Terminal Cap Female Dummy ad Terminal Plug Button _ gt Step 7 19 16 45065 01 11 05 09 Hunter Fan Company 8 1 8 2 8 4 8 5 8 6 8 Operating and Cleaning Your Ceiling Fan Turn on electrical power to the fan The fan pull chain controls power to the fan The pull chain has five settings in sequence High Medium Low Serenity Speed and Off e Pull the chain slowly to change settings e Release slowly to prevent the chain from recoiling into th
4. Hanger Bracket 3 45065 01 11 05 09 Hunter Fan Company Ceiling Height Preparing the Fan Site continued Step 2 Cut the Ceiling Hole 2 1 Locate the site for the ceiling hole directly below the joist or support brace that will hold the outlet box and fan 2 2 Cut a 4 diameter hole through the drywall or plaster of the ceiling You will use the hole to install the support brace and outlet box Step 3 Install a Support Brace If Necessary Determine if there is a ceiling joist directly above the ceiling hole If the joist is there determine if it is positioned to allow you to recess the outlet box a minimum of 1 16 into the ceiling If NOT install a support brace as follows 3 1 Attach a 2 x 4 support brace between two joists Position it to allow you to recess the bottom of the outlet box a minimum of 1 16 into the ceiling 3 2 Check the support brace to ensure it will support the full weight of the fan and light kit Step 4 Install the Outlet Box 4 1 Obtain a UL approved octagonal 4 x 1 1 2 outlet box plus two 8 x 1 1 2 wood screws and washers available from any hardware store or electrical supply house 4 2 Orient the outlet box so that both the inner and outer holes in the box align with the joist or support brace 4 3 Drill pilot holes no larger than the minor diameter of the wood screws 5 64 through the inner holes of the outlet box 4 4 Attach the
5. 2 3 2 4 2 Installing the Hanger Bracket Drill two pilot holes into the wood support structure through the outermost holes in the outlet box The pilot holes should be 9 64 in diameter Note Your fan comes with four pre installed neoprene noise isolators Thread the lead wires from the outlet box down through the hole in the middle of the hanger bracket Align the slotted holes in the hanger bracket with the pilot holes you drilled in the wood support structure For proper alignment use slotted holes directly across from each other If you are installing the fan on an ANGLED ceiling be sure to orient the hanger bracket as shown in Illustration 2 3 left or right view Note The isolators should be flush against the ceiling Place a flat washer on each of the two 3 screws and pass the screws through the slotted holes in the hanger bracket into the pilot holes you drilled Tighten the screws into the 9 64 pilot holes do not use lubricants on the screws Do not over tighten Flat Washer Large n 3 Screw LEFT ALAALA SS y fl Isolator Hanger Bracket Steps 2 2 2 4 Ceiling Peak Step 2 3 Angled Ceiling Only 45065 01 11 05 09 e Hunter Fan Company Ceiling Peak Large 3 Assembling and Hanging the Fan You can assemble your fan for standard or angled mounting as shown in steps 3 1 3 3 For low pr
6. ceiling fan be sure you can do the following e Locate the ceiling joist or other suitable support in ceiling e Drill holes for and install wood screws e Identify and connect electrical wires e Lift 40 pounds If you need help installing the fan your Hunter fan dealer can direct you to a licensed installer or electrician Gathering the Tools You will need the following tools for installing the fan e Electric drill with 9 64 bit e Standard screwdriver magnetic tip recommended e Phillips head screwdriver magnetic tip recommended e Wrench or pliers e Ladder height dependent upon installation site Checking Your Fan Parts Carefully unpack your fan to avoid damage to the fan parts Refer to the included Parts Guide Check for any shipping damage to the motor or fan blades If any parts are missing or damaged contact your Hunter dealer or call Hunter Technical Support Department at 888 830 1326 In Canada call 1 866 268 1936 Preparing the Fan Site Before you begin installing the fan follow all the instructions in Preparing the Fan Site Proper ceiling fan location and attachment to the building structure are essential for safety reliable operation maximum efficiency and energy savings 6 Installing Multiple Fans If you are installing more than one fan keep the fan blades and blade irons if applicable in sets as they were shipped 45065 01 11 05 09 Hunter Fan Company 2 2
7. inches of the fan blade tips e The fan is directly below a joist or support brace that will hold the outlet box and the full weight of the fan 30 From Wall or Nearest Obstruction 7 Minimum Blades to Floor 8 Minimum Checklist for Existing Fan Site If you want to use an existing fan site complete the following checklist to Fan Support determine if the site is acceptable and safe for your new Hunter fan If you cannot check off every item prepare a new fan site as described on this page Fan Support System e Fan attaches directly to building structure e Fan support system will hold full weight of the fan and light kit Ceiling Hole The outlet box clearance hole is directly below the joist or support brace Outlet Box e The outlet box is an UL approved octagonal 4 x 1 1 2 outlet box or as specified by the support brace manufacturer The outlet box is secured to the joist or support brace by wood screws and washers through the inner holes of outlet box The outer holes of the outlet box are aligned with joist or support brace e The bottom of the outlet box is recessed a minimum of 1 16 into ceiling Wiring e The electrical cable is secured to outlet box by an approved connector e Six inches of lead wires extend from outlet box Suitable Existing Fan Site Fan Support Outlet Box If your existing fan site is suitable skip ahead to Section 2 Installing the
8. outlet box directly to the support brace or joist with two 8 x 1 1 2 wood screws and washers Th e bottom of the outlet box must be recessed a minimum of 1 16 into the ceiling Step 5 Prepare the Wiring 5 1 Make sure the circuit breakers to the fan supply line leads and associated wall switch location are turned off If you cannot lock the circuit breakers in the off position securely fasten a prominent warning device such as a tag to the service panel 5 2 Thread the fan supply line through the outlet box so that the fan supply line extends at least 6 beyond the box 5 3 Attach the fan supply line to the outlet box with an approved connector available at any hardware store or electrical supply house 5 4 Make certain the wiring meets all national and local standards and ANSI NFPA 70 You have now successfully prepared your ceiling fan site For instructions to install your ceiling fan go to your fan manual and continue with Section 2 Installing the Hanger Bracket 4 45065 01 11 05 09 Hunter Fan Company A CAUTION All wiring must be in accordance with national and local electrical codes and ANSI NFPA 70 If you are unfamiliar with wiring use a qualified electrician Installer s Choice and Optional Accessories Support Brace Ceiling Standard Outlet Box Mounting gt Style Standard Mounting hangs from the ceiling by a dow
9. e blades e The chain uses a breakaway connector that separates if the chain is jerked If this happens simply reinsert the chain into the connector chain has two settings ON and OFF Ceiling fans work best by blowing air downward counterclockwise The light pull chain controls the power to the light fixture The blade rotation in warm weather to cool the room with a direct breeze In winter having the fan draw air upward clockwise blade rotation will distribute the warmer air trapped at the ceiling around the room without causing a draft For cleaning finishes use a soft brush or lint free cloth to prevent scratching A vacuum cleaner brush nozzle can remove heavier dust Remove surface smudges or accumulated dirt and dust using a mild detergent and a slightly dampened cloth You may use an artistic agent but never abrasive cleaning agents as they will damage the finish Clean wood finish blades with a furniture polishing cloth Occasionally apply a light coat of furniture polish for added protection and beauty Clean painted and high gloss blades in the same manner as the fan finish To Change Airflow Direction Turn the fan off and let it come to a complete stop Slide the reversing switch on the fan to the opposite position Restart fan 45065 01 11 05 09 Hunter Fan Company Reversing Switch 17 gt In warm weather use downward air flow pattern In cold w
10. eather use upward air flow pattern 9 Troubleshooting Problem Nothing happens fan does not move 1 Turn power on replace fuse or reset breaker 2 Loosen canopy check all connections according to the wiring the fan section 3 Check the plug connection in the switch housing 4 Push motor reversing switch firmly left or right to ensure that the switch is engaged 5 Pull the pull chain to ensure it is on 6 Remove the shipping bumpers Problem Noisy operation 1 Tighten the blade assembly screws and blade iron armature screws until snug 2 Check to see if the blade is cracked If so replace all the blades Problem Excessive wobbling 1 If your fan wobbles when operating use the enclosed balancing kit and instructions to balance the fan 2 Tighten all blade iron screws 3 Turn power off support fan very carefully and check that the hanger ball is properly seated In compliance with U S Federal regulations this ceiling fan contains a wattage saver that limits the light output to 190 Watts The following issues may arise if total wattage exceeds 190 Watts Issue Lights dim when turned on oblem Lights dim when turned on or do not turn on 1 It is normal for the lights to dim a couple of seconds after they are turned on To prevent the lights from dimming make sure the wattage of light bulbs installed match the specifications on the light sockets Issue Light shuts off suddenly r
11. g and Hanging the Fan Low Profile Only You can assemble your fan for standard or angled mounting as shown in steps 3 1 3 3 on the previous page For low profile mounting ceilings less than 8 feet high see steps 3 6 3 10 on this page 3 6 Remove the screws from the hanger ball bracket 3 7 Place the low profile washer from the parts sack into the canopy 3 8 Place the canopy trim ring and canopy with washer on top of the fan assembly 3 9 Align the screw holes in the washer with the holes in the adapter Assemble securely with three 8 32 x 3 4 screws 3 10 Raise the fan and place the hook on the hanger bracket through the round hole in the rim of the canopy A WARNING Fan may fall if not assembled as directed in these installation instructions Steps 3 8 3 9 Low Profile Washer Step 3 7 Detail Low Profile Washer Adapter Canopy Trim Ring 8 32 x 3 4 Screw 9 45065 01 11 05 09 e Hunter Fan Company 4 Wiring the Fan All wiring must be in accordance with national and local electrical codes and ANSI NFPA 70 If you are unfamiliar with wiring use a qualified electrician Wall switches are not included Select an acceptable general use switch in accordance with national and local electrical codes 4 1 4 2 4 3 4 4 4 5 4 7 Before attempting installation make sure the power is still off To connect the wires hold the bare me
12. h and tighten all three assembly screws could result in the switch housing and light fixture falling 7 5 If you want to install the light fixture proceed with step 7 6 now If you do not want to install the light fixture you need to uninstall it now See Uninstalling the Light Fixture on step 7 15 Once you have uninstalled the light fixture continue with step 7 6 13 45065 01 11 05 09 Hunter Fan Company 7 Completing Your Installation With or Without a Bowl Light Fixture Continued 7 6 To attach the lower switch housing connect the upper plug 7 7 connector from the motor to the lower plug connector in the lower switch housing assembly Note Both plug connectors are polarized and will only fit together one way Make sure the connectors are properly aligned before connecting them Incorrect connection could cause improper operation and damage to the product Place the lower switch housing assembly over the upper switch housing Align the side screw holes in the upper and lower switch housings Attach the lower switch housing to the upper switch housing with three housing assembly screws 14 45065 01 11 05 09 Hunter Fan Company Plug Connector A Steps 7 6 7 7 Lower Switch Housing Plug T Connector Detail Housing Assembly Screw 7 Completing Your Installation With or Without a Bowl Light Fixture Continued Ins
13. ion securely fasten a prominent Trim Ring warning device such as a tag to the service panel All wiring must be in accordance with national and local electrical codes and ANSI NFPA 70 If you are unfamiliar with wiring use a qualified electrician To reduce the risk of personal injury do not bend the blade attachment system when installing balancing or cleaning the fan Never insert foreign objects between rotating fan blades To reduce the risk of fire electrical shock or motor damage do not use a solid state speed control with this fan Use only Hunter speed controls Table Of Contents 2 Installing the Hanger Bracket 3 e Assembling and Hanging the Fan 8 6 Assembling the Blades 7 Completing Your Installation With or Without a Bowl Light Fixture 8 Operating and Cleaning Your Ceiling Fan 9 Troubleshooting 2009 Hunter Fan Company 2 45065 01 11 05 09 Hunter Fan Company Preparing the Fan Site Step 1 Choose the Fan Site Proper ceiling fan location and attachment to the building structure are essential for safety reliable operation maximum efficiency and energy savings Choose a fan site where e No object can come in contact with the rotating fan blades during normal operation e The fan blades are at least 7 feet above the floor and the ceiling is at least 8 feet high The fan blades have no obstructions to airflow such as walls or posts within 30
14. nrod included Angled Mounting recommended for a vaulted or angled ceiling Understanding Mounting and Installers Choice Hunter s patented 3 position mounting system provides you maximum installation flexibility and ease You can install your Hunter fan in one of three ways depending on ceiling height and your preference Low Profile Standard or Angled mounting The steps in this manual include instructions for all three Installer s Choice mounting methods Considering Optional Accessories Consider using Hunter s optional accessories including a wall mounted or remote speed control To install and use the accessories follow the instructions included with each product For quiet and optimum performance of your Hunter fan use only Hunter speed controls For ceilings higher than 8 feet you can purchase Hunter extension downrods All Hunter fans use sturdy 3 4 diameter pipe to assure stability and wobble free performance Support Brace Low Profile ad Mounting Style Outlet Box Low Profile Mounting fits close to the ceiling recommended for ceilings less than 8 feet high 5 45065 01 11 05 09 Hunter Fan Company A CAUTION To reduce the risk of personal injury attach the fan directly to the support structure of the building according to these instructions and use only the hardware supplied l Getting Ready To install a
15. oblem If the light on this fan shuts off suddenly 1 Turn the power to the fan off at the wall switch Wait 30 seconds then resume power to the fan 2 If lights shut off suddenly again check to make sure total wattage of bulbs does not exceed 190 Watts 18 45065 01 11 05 09 Hunter Fan Company gt If you need parts or service assistance please call 888 830 1326 In Canada call 1 866 268 1936 or visit us at our Web site at http www hunterfan com Hunter Fan Company 7130 Goodlett Farms Pkwy 400 Memphis Tennessee 38016
16. ofile mounting ceilings less than 8 feet high go to steps 3 6 3 9 on the next page 3 1 3 2 3 3 3 4 3 5 To assemble fan to hang down from a flat or angled ceiling place the canopy and canopy trim ring around the adapter so that they rest on the fan assembly Feed the wires from the fan through the downrod Note Make sure all the wires are on the same side of the metal dowel pin inside the dowrod Loosen the square head setscrew on the adapter to install the pipe and ball assembly Note When the pipe and ball assembly is fully installed 2 3 threads on the pipe will still be visible this is normal Securely retighten the setscrew with a wrench or pliers A CAUTION The adapter has a special coating on the threads Do not remove this coating the coating prevents the downrod from unscrewing Once assembled do not remove the downrod A WARNING Do not carry or lift fan by canopy Raise the fan and place the ball into the hanger bracket Align the notch on the ball with the indent in the hanger bracket Rotate the fan until you hear the notch pop into place Go to 4 e Wiring the Fan A WARNING Fan may fall if not assembled as directed in these installation instructions 8 Steps 3 1 3 3 7 m Downrod lt Canopy with Washer Canopy Trim Adapter Ring Steps 3 4 3 5 45065 01 11 05 09 Hunter Fan Company 3 e Assemblin
17. tal leads together and place a wire connector over them then twist clockwise until tight For all these connections use the wire connectors provided Connect the bare or green ground wire grounding from the ceiling to the green ground wire grounding from the ceiling plate and the green ground wire from the fan or the green ground wire present on the low profile washer Connect the white wire grounded from the ceiling to the white wire grounded from the fan Connect the remaining wires as follows Dual Switch Wiring e The black wire ungrounded from the ceiling to the black wire ungrounded from the fan e The black white wire ungrounded from the fan to the wire ungrounded for the wall switch Single Switch Wiring e The black wire ungrounded from the ceiling to the black ungrounded and the black white wire ungrounded from the fan A CAUTION Be sure no bare wire or wire strands are visible after making connections Turn the wire connectors upward and push them carefully back through the ceiling plate into the outlet box Spread the wires apart with the grounded wires on one side of the outlet box and the ungrounded wires on the other side of the outlet box 10 Wire Connector 45065 01 11 05 09 Hunter Fan Company 5 1 5 2 5 3 5 4 5 Installing the Canopy and Canopy Trim Ring
18. talling the Glass Bowl 7 8 First install B10 candelabra bulbs 60 Watt Maximum into the sockets 7 9 Thread the light and fan pull chains through the hole in the center of the glass bowl Then thread the light pull chain through the hole Breien in the center of the cover plate Connector 7 10 Thread the fan pull chain through the grommet hole in the side of the cover plate 7 11 Place the cover plate up against the glass bowl Align the holes in the cover plate and glass bowl 7 12 Thread the light pull chain through the finial and screw the finial onto the threaded rod end until tight 7 13 Attach the extra pull chains included to the light and fan pull chains using the plastic breakaway connector You may find the plastic breakaway connector on the end of the extra chain 1 Light Bulb Note In compliance with U S Federal Ii a energy regulations this ceiling nahha fan contains a wattage saver og Based 60 Watt that restricts the light kit to Maximum a maximum of 190 Watts Metal Disc Exceeding that limit or the Threaded Rod specifications on the light sockets may result in fire hazard lt _ Glass Bowl or improper operation If lights do not appear to be operating properly see the troubleshooting section E lt __ _ Cover Plate lt lt Finial 45065 01 11 05 09 e Hunter Fan Company 7 Completing Your Installation With or Without a Bowl Light Fixture Continued
19. w through the blade iron and attach lightly to the fan Insert the second blade mounting screw then securely tighten both mounting screws Blade Assembly Use with grommet ews Use without grommet Blade Mounting Screw 12 45065 01 11 05 09 Hunter Fan Company Steps 6 1 6 2 7 Completing Your Installation With or Without a Bowl Light Fixture Your Hunter fan comes with an integrated light fixture assembly and an optional switch housing cap and plug button This feature gives you the option of installing the fan with OR without the included light fixture The steps below direct you whether or not you are installing a light fixture A WARNING Use only the light fixture supplied with this fan model 7 1 To attach the upper switch housing partially install two housing assembly screws into the switch housing mounting plate 7 2 Feed the upper plug connector through the center opening of the housing 7 3 Align the keyhole slots in the housing with the housing assembly screws Steps 7 1 7 3 Housing 7 4 Turn the housing counterclockwise until the housing assembly Assembly Upper Screw Switch screws are firmly situated in the narrow end of the keyhole slots Install the remaining screw into the housing Tighten all three screws firmly Housing A CAUTION Make sure the upper switch housing is securely attached to the switch housing mounting plate Failure to properly attac
Download Pdf Manuals
Related Search