Hayter Mowers 493F Lawn Mower User Manual
Contents
1. 20 INTRODUCTION Thank you for purchasing a Hayter mower The following pages are designed to help you gain safe and efficient service from your machine IMPORTANT This Owners Handbook should be regarded as part of the mower as it gives essential information regarding mower safety operation maintenance and specifica tions Read and understand this handbook prior to operating your mower for the first time Make sure you are familiar with all the controls and points of regular maintenance If you have any doubts consult your local Hayter authorised dealer who will be pleased to give you assistance IMPORTANT This mower is designed solely for use in a domestic grass cutting environment Use in any other way is considered as contrary to the intended use Compli ance with and strict adherence to the conditions of operation service and repair as speci fied in this handbook also constitute essential elements of the intended use This mower should be operated serviced and repaired only by persons who are familiar with its particular characteristics and who are acquainted with the relevant safety proce dures The safety precautions listed in this handbook and all other generally recognised regula tions on safety must be observed at all times Use of non standard parts or any arbitrary modifications carried out on this machine may relieve Hayter Limited of liability for any resulting damage or injury Hayter mowers are r2. Cutterblade Fig 36 MOWER MAINTENANCE Cutterblade Sharpening A slightly worn cutterblade may be re sharpened Both blade edges must be sharpened equally to ensure balance Sharpen the cutterblade every 25 mowing hours or more frequently if conditions require Remove the cutterblade from the mower and clean using a brush and water In spect the cutterblade for signs of damage Sharpen both cutting edges with a flat file to restore per formance Refer fig 36 Ensure that the cutterblade is balanced Use a screw driv er with a round shaft to support the cutterblade through its centre hole Hold the cutterblade horizontal and then release A balanced cutterblade will remain horizontal Refer fig 37 If the cutterblade is not balanced the heavy end will rotate downwards Sharpen the heavy end until the cutterblade is correctly balanced Refer fig 38 Storage To store the handlebar unscrew the 2 small securing knobs sufficiently to allow it to be pivoted forwards to rest against the mower Take care to ensure that the con trol cables do not become snagged at the pivot point and depress the engine stop lever to prevent it being damaged through contact with the engine Refer fig 39 Fig 38 Engines stored in excess of 30 days need to be protected with Briggs amp Stratton fuel additive or drained of fuel to prevent gum from forming in the fuel system or on essen tial carburettor parts To ensure your mower is ma
3. HAYTER EE MAKERS OF THE FINEST MOWERS Harrier 48 56 BBC CODES 493F amp 563F OWNER S HANDBOOK Original Version EN ISSUE 20 12 10 PART NUMBER 111 3782 B CONTENTS Contents Introduction Specifications Main Features Safety Precautions Safety Alert Symbol Training Preparation Safety Symbols Operation Maintenance amp Storage Control Symbols Assembling the Mower Before First Use Delivery Checklist Handlebar Grassbag Assembly Prevent Engine Damage Oil Type Check Oil Level Fuel Type Operating The Mower Controls Starting Engaging Cutterblade Drive Forward Travel Reverse Travel Turning Stopping Slopes Height of Cut Before Mowing DO Ur Ur Ur Un Una Un AAA A VO O NW 00 00 00 00 00 00 00 o 1 a Grassbag Without Grass Collection Heavy Growth Blade Brake Clutch Non Grassed Areas Maintenance Schedule Mower Maintenance Carburettor Adjustments Oil Service Air Cleaner Service Spark Plug Service Keeping Engine Clean Grassbag Deck Housing Securing Nuts and Bolts Clutch Cable Adjustment Lubrication Cutterblade Removal Cutterblade Assembly Cutterblade Sharpening Storage Lawn Care Calendar Trouble Shooting Warranty Notes Customer Info Service Records OOOO o 10 13 10 10 11 11 11 11 11 12 12 12 12 13 13 14 15 16 16 19
4. HAYTER EE MAKERS OF THE FINEST MOWERS Hayter Limited Spellbrook Bishop s Stortford Herts CM23 4BU England Note for dealer Please retain this voucher for your records Website www hayter co uk 20
5. Hours After the very first five hours change the engine oil Adjust the autodrive clutch cable Daily Check the oil level Remove grass debris from around the engine exhaust exhaust guard air ways in the top cowl underside of the deck housing and from the grassbag and check for signs of damage Check the condition of guards and safety devices Check condition of cutterblade 25 Hours Or Every Season Change the engine oil if continuously operating under heavy load or high ambient temperature Service the air cleaner Lubricate wheels pivot points and linkages and grease the inner control cables at point of entry and exit from Air Cleaner Fuel Cap Start Grip Cover Oil fill Dipstick Exhaust Guard Exhaust Spark Plug Lead Carburettor S ES SO Cass SSS Fig 23 their outer casing Check the clutch cable adjustment Sharpen the cutterblade 50 Hours Or Every Season Change the engine oil 100 Hours Or Every Season Clean the engine cooling system Clean more often under dusty conditions or when airborne debris is present or after prolonged operation whilst cutting tall dry grass Replace the spark plug Engine Detail Refer fig 22 Carburettor Adjustments Should only be made by an authorised Briggs amp Stratton dealer Under no circumstances should the engine be adjusted to run at a speed in excess of that shown on the Declaration of Conformity Oil Service Check the oil level
6. guard or cooling fins when the engine is hot Stop the engine and disconnect the spark plug lead Before clearing blockages or unclogging the dis charge chute Control Symbols B AA je Slow Height of Cut Adjustment Before cleaning checking or working on the ma chine After striking a foreign object Inspect the machine for damage and ensure necessary repairs are made before re starting and operating Ifthe machine starts to vibrate abnormally check immediately Stop the engine Whenever you leave the mower Before refuelling Move the throttle to the stop position Maintenance amp Storage A Keep all nuts bolts and screws tight to ensure that the equipment is in safe operating condition Frequently check fuel lines and fittings for cracks or leaks and replace if necessary Inspect the exhaust periodically and replace if worn or leaking Never store the mower with petrol in the tank within an enclosed area where fumes may reach an open flame or spark Allow the engine to cool before storing in any enclosure Fast Fast Slow lay ee t Variable Speed Control Throttle Control To reduce the fire hazard keep the engine and the surrounding deck area free of grass leaves or excessive grease Check the rear deflector and grassbag frequently for wear or deterioration Replace worn or damaged parts for safety If the fuel tank has to be drained this should be done outdoors
7. its left hand side and ensure that the air cleaner side of the engine is uppermost Refer fig 34 Remove the two socket head screws 1 and Former BBC blade 2 and plate clamp BBC 3 Refer fig 35 To prevent accidents never work on the cutterblade unless the spark plug lead has been removed The cutterblade has sharp edges ALWAYS wear strong gloves to protect your hands when working on the cutterblade DO NOT rotate tools towards the cutting edges to avoid the risk of injury should the tool slip ALWAYS use genuine Hayter replacement parts The condition of the cutterblade and its mounting arrangement should be checked regularly for signs of wear or damage Ensure that the cutterblade is not bent or cracked A damaged cutterblade that is out of balance will vibrate excessively and may break DO NOT use an unbalanced cutterblade Fig 33 13mm extension Clutch lever N fully engaged 3 yA Tighten the inner nut when the cable spring is set 2 Metal adjuster 12 Regularly check that the bolt securing the cutterblade is tightened to the specified torque of 55Nm Replace the cutterblade every 2 years of sooner if excessively worn or damaged To prevent injury it is wise to seek assistance when turning the mower on its side Cutterblade Assembly Assemble the two socket head screws 1 Former BBC blade 2 and Plate clamp BBC 3 Tighten to a torque of 55Nm Refer fig 35 Fig 35
8. to the cable the Variable speed Control should only be operated whilst the engine is running Starting Stand behind the mower hold the handlebar together and move the throttle to the fast position With your right hand hold the engine start grip and pull slowly until resistance is felt release then pull rapidly to crank the engine Carefully return the start grip to the storage position when the engine starts Refer fig 8 If the engine does not start after 3 5 attempts Refer to Trouble Shooting Note The cutterblade is not engaged at this stage To prevent damage never pull the engine start grip when the engine is running Engaging Cutterblade Drive Always make sure the throttle stop lever is fully Fig 8 forward 1 Pull the blade stop lever back against the handlebar at the same time and hold in position 2 To engage the BBC cutterblade first push the actuat ing lever forward and down until it clicks into position Refer fig 9 Disengage Cutterblade Drive 1 Release the blade stop lever and it will return to its rest position Refer fig 10 amp 11 Emergency Stop If the cutterblade drive mechanism fails stop the engine Forward Travel Hold the handlebar and operate the ground drive clutch lever to power the mower in a forward direction When the ground drive clutch lever is disengaged the mower may be pushed This feature is useful when mow ing in confined areas Ground speed ma
9. 15 Grassbag Assembly 16 Rear Deflector 17 Height Of Cut Adjuster 18 Battery Cover 19 Exhaust Guard Note Item 14 should only be operated whilst the engine is running or the cable will be damaged 563 Briggs amp Stratton Series 850 2750 rpm Unleaded petrol 1 5 litres SAE 30 engine oil 0 6 litres 560mm 13 60mm 1080 x 585 x 1510mm 51 Kg SAFETY PRECAUTIONS Safety Alert Symbol A This safety alert symbol indicates important safety messages When you see this symbol be alert to the possibility of injury Carefully read the following and inform others Your mower is perfectly safe if used correctly Failure to observe the following precautions may result in serious injury Training A Before using the mower read the owners handbook carefully Pay particular attention to the safety precautions Ensure that you are familiar with the controls and the proper use of the equipment Learn how to stop the mower quickly in an emergency Never allow children or people unfamiliar with these instructions to use the mower Local regulations can restrict the age of the operator Never mow while people especially children or pets are nearby Keep in mind that the user is responsible for accidents or hazards occurring to other people or their property Safety Symbols E Et Stop engine and remove spark plug lead before working on the mower EU Safety Alert Be aware to the possibil
10. 25 Replace the spark plug every 100 hours or every season whichever occurs first A spark plug wrench is available from any authorised Briggs amp Stratton service dealer Check the spark plug gap with a feeler gauge and set at 0 50mm Refer fig 26 Keeping Engine Clean Remove all grass and debris from the engine including the exhaust exhaust guard the air ways in the top cowl and the surrounding deck areas on a daily basis after use Never spray the engine with water during cleaning Water can contaminate the fuel Always clean with a brush or compressed air Refer fig 27 Grass and debris may clog the engine s air cooling system especially after prolonged operation while cutting tall dry grass The internal cooling fins and surfaces may require cleaning to prevent overheating and engine damage We recommended that this service be carried out by an authorised Hayter Service dealer Grassbag A Remove grass debris from the grassbag immediately Fig 26 after use and check its condition for signs of damage To prevent accidents replace a damaged grassbag immediately Refer fig 28 Deck Housing Remove grass debris from the top and underside of the deck housing immediately after use Refer fig 29 Fertilisers and top dressings are particularly corrosive Thoroughly clean the mower deck immediately after use on treated grass and store well away from corrosive materials Securing Nuts amp Bolts Regularly check th
11. Crankshaft Consult your dealer Undulating ground conditions Change direction of travel Cutterblade worn Sharpen cutterblade Cutterblade out of balance Balance the cutterblade Wheels roller damaged Insect amp replace as necessary Uneven cut WARRANTY Hayter Limited warrants to the original user purchaser that this unit shall be free from defects in material and workmanship under normal use and service for a period of three years from the date of purchase The manufacturer of major proprietry components ie engines gearbox transaxle where applicable furnish their own warranty and services are provided through their authorised network To qualify for the full benefit of the warranty the warranty registration card must be returned within 14 days of purchase Subject to the conditions and exclusions noted in this limited warranty we shall at our option repair or replace any warranted part during the applicable period If you are in doubt or experience any difficulty please consult a Hayter Authorised Service Dealer for clarification To qualify for the extended warranty second and third year of the three year limited warranty the machine must have annual services carried out by an Authorised Hayter Service Dealer These chargeable services should be carried out within 12 and 24 months of the date of purchase Excluded from the extended warranty period are those items which are subject to normal wear and tear
12. and when the engine is cool Wear strong work gloves when removing and reassem bling the cutterblade Cutterblade Cutterblade Engage Disengage l dy E Sl i Cutterblade Symbol ASSEMBLING THE MOWER BEFORE FIRST USE Delivery Checklist Remove the mower from the packaging and check that the following items have been supplied correctly If any items are missing contact your local Hayter dealer 1 Engine Handbook 2 Grassbag 3 Parts list D of C 4 Warranty Reg Card To prevent accidents cut off the long ribbon attached to the grassbag and discard Refer fig 1 Handlebar Unscrew the handlebar securing knobs sufficiently to allow the handlebar to pivot Move the blade stop lever away from the engine to avoid damage and unfold the handlebar to the operating position Refer fig 2 Tighten both handlebar knobs to secure in position Take care to ensure that the control cables do not become snagged at the pivot point Grassbag Assembly Before first use assemble the grassbag and frame Slide the frame 1 into the grassbag 2 ensuring that the han dle is above the grassbag as shown Attach plastic clips A B C and D to the grassbag frame Refer fig 3 Raise the rear deflector lower the grassbag and hook in Fig 1 Fig 2 Fig 3 position Lower the deflector to rest on the grassbag Prevent Engine Damage To prevent engine damage the engine is shipped without oil or petrol The engine mu
13. at all securing nuts and bolts are tight Replace missing or damaged items immediately MOWER MAINTENANCE Clutch Cable Adjustment At any time the operator feels that the machine is loosing drive 1 Stop the engine 2 Pull the machine backwards at the same time progressively engage the clutch lever until the rear rollers lock at this point the clutch lever should be 60mm from the handlebar 3 If the distance between the clutch lever and handlebar is less than 60mm regulate the engagement position with the black plastic cable adjuster To regain the 60mm distance Refer fig 30 amp 31 4 Note this is a temporary adjustment and at the nearest opportunity a service should be carried out to ensure the spring on the clutch cable attached to the gearbox clutch is set correctly This adjustment should be done using the metal adjuster at the control with the plastic adjuster reset fully wound in When the spring is set tighten the inner lock nut to secure position Refer figs 32 amp 33 Lubrication Lubricate the wheels pivot points and linkages with engine oil every 25 operating hours Apply a good quality medium grease to the inner control Fig 30 Fig 31 60mm cables at the point of entry and exit from their outer cas ing Cutterblade Removal Ay Drain the fuel by running the engine until the fuel tank is empty and the engine stops Remove the spark plug lead and allow the engine to cool Turn the mower on
14. daily before starting the engine and ensure that the correct oil level is maintained Refer to Before Starting the Mower for oil checking and filling instructions Change the engine oil after the first 5 hours of operation and thereafter according to the Maintenance Schedule 1 Drain fuel by running the engine until the fuel tank is empty Remove the spark plug lead Allow the engine to cool Drain the oil while the engine is warm not hot Tip the mower over on to its left hand side thus ensuring that the air cleaner is kept uppermost to prevent engine damage 6 Remove the oil filler dipstick and drain the oil into a suitable container 7 Refill with new oil of the recommended SAE viscos ity grade Refer to Before Starting the Mower Refer fig 23 QU Bu Dn Air Cleaner Service To service the air cleaner loosen screw 1 and remove cover 2 Refer fig 24 Remove cartridge 3 and clean by tapping gently on a flat surface If very dirty replace Do not use petroleum solvents Do not use pressurised air Do not oil the cartridge After servicing install the cartridge into the cover Insert the tabs on the bottom of the cover into the slots in the bottom of the base 4 Tilt the cover upwards and se MOWER MAINTENANCE Spark Plug Service Use only Briggs amp Stratton Part number 19368 spark tester 1 to check for a spark as shown in the diagram Refer fig
15. e g tyres wheels cutterblades belts cables grassbags sweeper brushes batteries and other consumable wearing parts All consumer machines which are fitted with a genuine Hayter friction disc as original equipment before use are covered by a Lifetime Warranty against the engine crankshaft bending Note friction washers blade brake clutch B B C units and other such devices are not applicable Only machines fitted with a genuine Hayter friction disc which are used in accordance with the recommended operating and maintenance procedures are covered This warranty does not apply to any unit that has been tampered with altered misused abused or used for hire and will become invalid if non genuine Hayter parts are fitted This warranty does not cover minor mechanical adjustments unless they are due to defective material or workmanship Consult the Owner s Handbook or a Hayter Authorised Service Dealer for assistance when making these adjustments A warranty period of 90 days applies to machines used for commercial purposes To make a warranty claim return the unit to a Hayter authorised dealer along with proof of purchase stating the machine serial number and date of purchase The service receipt s or this Owners Handbook with the Ist 2nd year service boxes fully completed must be produced as proof of entitlement to the extended warranty period Subject to the conditions and exclusions in this limited warranty the authorised dealer wil
16. g notch then push forwards to lower or pull backwards to raise the height of cut Finally release the lever at the required position and ensure it locks firmly into one of the eight setting notches Always select a height of cut to suit operating conditions Aim to prevent engine overloading and blockages by avoiding low cuts in long grass conditions Be prepared to make two cuts when the grass is long Refer fig 14 Before Mowing A To prevent accidents thoroughly inspect the area and remove all objects which when contacted by the mower cutterblade could become dangerous projec tiles Inspect the area for hidden obstructions which when contacted by the cutterblade could risk health and safety or result in damage to the mower Remem ber the location of these obstructions and ensure that you mow around them Refer fig 15 Grassbag Raise the rear deflector and lift the grassbag and lower the rear deflector to rest against the rear of the mower To empty the grassbag pour out the grass clippings and shake the grassbag vigorously to clean the airways Good grass collection depends on good air flow through the grassbag When collecting grass clippings it is important that the grassbag is emptied regularly to prevent block ages and engine overloading Refer fig 16 Without Grass Collection Remove the grassbag and operate the mower with the rear deflector in the closed position Refer fig 17 Heavy Growth Areas of heavy growth sho
17. grass where feasible Always be sure of your footing on slopes Walk never run Do not mow excessively steep slopes of more than 20 and mow across the face of slopes never up and down Exercise extreme caution when changing direction Use extreme caution when reversing or pulling the mower towards you Always replace worn or faulty parts with genuine Hayter parts This machine contains spring loaded assemblies which could cause a hazard when disassembled and reassembled Maintenance should only be carried out by a Hayter authorised dealer ko Carefully read the Danger of being hit Keep bystanders at Danger of severing Owners Handbook be by thrown objects a safe distance from toes or fingers in fore using the machine the mower cutting mechanism 5 Engine Start SAFETY PRECAUTIONS Operation cont A Never operate the machine with defective guards or with out safety devices for example deflectors and or grass bag in place Do not change the engine governor settings or overspeed the engine Start the engine carefully with feet well away from the cutterblade and always disengage the rear roller drive clutch before starting the engine Do not tilt the mower when starting the engine Do not start the engine when standing in front of the discharge chute Do not put hands or feet near or under rotating parts Never pick up or carry the machine while the engine is running Never touch the exhaust exhaust
18. hould merely top the grass as close cutting at this stage could result in severe yellowing or browning Two cuts are generally sufficient this month April Mow often enough to stop grass growing away Dig out patches of coarse grass or resistant weed Re seed bare patches May Keep mowing increasing the frequency as required Treat with selective weed killers or combined weed feed preparations if you did not feed the lawn in April June Summer mowing should now be under way It should be necessary to mow the lawn twice a week Raking before mowing is important this month as the combined action keeps runners of clover under control Water the grass if necessary and remember to soak thoroughly July Treat the grass with the second application of fertiliser or weed killer fertiliser Water when necessary and rake occasionally As a general rule the grass clippings should be removed each time you mow If weather conditions are dry and hot and the grass is weed free leave the clippings on the lawn to help maintain ground moisture August Keep mowing regularly and watering as necessary Fill any cracks caused by drought with a mixture of sharp sand and soil In dry weather conditions leave the grass longer to help retain ground moisture September Raise the height of cut to allow the grass to thicken and protect the roots from the winter frost and snow October Rake out the thatch from the turf and spike the lawn to ass
19. intained in good working order it is important that the following procedure is adopted Refer to the Maintenance section as necessary Drain fuel from the engine by operating the engine until it stops Disconnect the spark plug lead Change the engine oil Remove the engine spark plug and pour 15ml of engine oil into the engine cylinder and replace the spark plug Do not exceed the stated volume of oil as engine damage may occur on re starting Do not replace the spark plug lead Slowly pull the engine start grip once to crank the engine This will distribute the oil and help prevent engine corrosion Clean grass and debris from the engine cylinder cylinder head cooling fins under top cowl around and behind ex haust exhaust guard and ensure that the grassbag is clean Lubricate the mower and treat metal parts with a water repellent anti corrosion product Cover the mower with a protective sheet and store it ina dry ventilated area Fig 39 LA WN CARE CALENDAR To be used as a guide only January There is very little work to do this month apart from brushing away leaves Keep off the grass if frozen or waterlogged February Rake the grass thoroughly Spike the lawn to aerate and stimulate soil organisms and root growth and apply lawn sand if necessary March The yearly lawn work programme really starts this month As soon as the ground conditions are suitable the first cut can be made The first cut s
20. ist in drainage Brush in peat and sharp sand November Use a stiff broom to disperse worm casts before mowing Keep turf free from leaves December Apart from brushing away leaves December is a slack end of a busy year Keep off the lawn if it is very wet or frozen Lawn Stripes The way to achieve a neat striped effect is for the lawn being cut in parallel stripes alternate stripes being mown in opposite directions A much more important routine is to cut at right angles to the line of the previous mowing If the work has been carried in a north south line then the next cutting should be in an east west direction The cross cutting keeps down the coarse weed grasses To prevent grass damage do not remove more than one third of the grass height in one cut TROUBLE SHOOTING 1 Engine stop lever released 1 Operate engine blade stop Discharge chute blocks 1 Grass is wet 1 Mow dry grass lever 2 Cut height is too low 2 Increase cut height 2 Incorrect oil level 2 Check oil level 3 Grassbag full 3 Empty grassbag 3 Obstruction under deck 3 Remove obstruction 4 Airflow through the grassbag 4 Clean the grassbag 4 Battery discharged if fitted 4 Charge battery is restricted Engine will not turn over 1 Excess oil 1 Check oil level Mower is hard to push 1 Cut height too low 1 Increase cut height 2 Air cleaner cartridge oil 2 Service air cleaner 2 Wheels roller damaged 2 Inspect and replace as neces soa
21. ity of injury Preparation A While mowing always wear substantial footwear and long trousers Do not operate the equipment when barefoot or wearing sandals Thoroughly inspect the area where the mower is to be used and remove all objects which may be thrown by the machine WARNING Petrol is highly flammable store fuel in containers specifically designed for this purpose refuel outdoors only and do not smoke while refuelling add fuel before starting the engine Never remove the cap of the fuel tank or add petrol while the engine is running or when the engine is hot if petrol is spilled do not attempt to start the engine but move the machine away from the area of spillage and avoid creating any source of ignition until the petrol vapours have dissipated replace all fuel tank and container caps securely Replace faulty silencers A damaged cutterblade or loose fixing bolt are major hazards Before use always visually inspect the cutting mechanism to ensure that it is in good condition A damaged cutterblade must be replaced immediately with a genuine Hayter replacement part Operation A Do not operate the engine in a confined space where exhaust fumes carbon monoxide can collect Always pull the starter cord slowly until resistance is felt Then pull the cord rapidly to avoid kickback and prevent hand or arm injury Mow only in daylight or good artificial light Avoid using the machine on wet
22. ked or blocked sary aa En Mower will not self 1 Clutch out of adjustment 1 Adjust clutch cable Fuel starvation Fill fuel tan propel 2 Drive belt damaged 2 Replace drive belt a Fuel cap vent blocked Clean fuel cap vent Poor grass collection 1 Airflow through the grassbag 1 Clean the grassbag Engine under load Raise height of cut is restricted Incorrect contaminated fuel Drain tank and fill with correct 2 Discharge chute blocked 2 Remove blockage fuel 3 Wet grass 3 Mow in dryer conditions Spark plug lead disconnected 3 Connect spark plug lead 4 Grassbag full 4 Empty grassbag Engine will not start Engine brake not released 4 Operate engine brake lever Cutterblade drive will 1 Engine stop lever not fully 1 Push fully forward disengage Faulty spark plug 5 Clean and adjust the gap or not engage disengage forward replace 2 Faulty blade break clutch 2 Consult dealer Battery discharged if fitted 6 Charge battery Wiring fault 7 Check wiring Engine smokes Spark plug lead becoming 1 Connect spark plug lead disconnected in use 2 Faulty spark plug 2 Clean and adjust gap or replace 3 Air cleaner blocked 3 Service air cleaner 4 Incorrect contaminated fuel 4 Drain tank and fill with correct fuel Engine runs rough Mounting bolt loose Tighten bolts Engine vibrates exces 2 Cutterblade bolt loose Tighten bolt sively Cutterblade out of balance Balace cutterblade Bent
23. l at our option repair or replace any warranted part within the duration of the warranty period This limited warranty gives you specific legal rights and is in addition to any statutory rights to which you may be entitled and your statutory rights are not affected by this warranty If you need additional information concerning this written warranty or assistance in obtaining services please write to HAYTER LIMITED Service Department Spellbrook Bishop s Stortford Hertfordshire CM23 4BU UK ONLY Details of your local Hayter authorised dealer are contained in Yellow Pages and the Hayter website www hayter co uk or contact contact Freephone 0800 616298 Issue 01 09 09 CUSTOMER INFORMATION SERVICE RECORD CODE SERIAL NO HAYTER HAYTER Ml MAKERS OF THE FINEST MOWERS HA MAKERS OF THE FINEST MOWERS 1st Year 12 months 1st Year 12 months Owner s Name We certify that this service has been carried out by an Authorised Hayter Service Dealer Serial Number Date Date Note for dealer Please retain this voucher for your records Engine Type Engine Your Local Dealer HAYTER HAYTER MA MAKERS OF THE FINEST MOWERS EE MAKERS OF THE FINEST MOWERS aN AMY 2nd Year 24 months MER We certify that this service has been N DE carried out by an Authorised Hayter Service Dealer 2nd Year 24 months Serial Number Date Date
24. obustly constructed and designed for efficient economical perform ance under normal mowing conditions Correct operation and maintenance will ensure a long and satisfactory service life Prior to despatch from our factory every effort is made to ensure that your mower is delivered in perfect condition Throughout this handbook all references to left and right are as viewed from behind the handlebar in the direction of forward travel This handbook is based on information available at the time of publication HAYTER LIMITED reserve the right to amend product specifications without prior notification For a full range of products and to locate your nearest authorised sales stockist service or parts dealer please visit our website at www hayter co uk SPECIFICATIONS MAIN FEATURES Code 493 Engine Briggs amp Stratton Engine type Series 650 Engine Cutterbar Speed 2750 rpm Fuel type Unleaded petrol Fuel capacity 1 5 litres Oil type SAE 30 engine oil Oil sump capacity 0 6 litres Cutting width 480mm Cutting height 13 60mm Overall dimensions 1080 x 507 x 1510mm Weight 51 Kg l Spark Plug Lead 2 Engine Cover 3 Air Cleaner 4 Fuel Filler Cap 5 Oil Filler Cap and Dipstick 6 Serial No Label de Handlebar Securing Knob 8 Engine Start Grip 9 BBC Control Lever 10 Blade Stop Lever 11 Handlebar 12 Ground Drive Clutch Lever 13 Throttle Control amp Stop 14 Variable Speed Control see note
25. st be filled with the correct grade of oil and petrol before starting the engine Refer fig 4 Oil Type Always use high quality detergent oil classified SAE 30 oil Never use additives with recommended oil To prolong the life of your engine it is important that the oil is changed after the first 5 hours of use Refer to Maintenance Schedule Check Oil Level Clean around the oil filler cap before removing With the mower on a level surface unscrew and remove the oil filler dipstick Wipe oil from it with a clean cloth Screw the oil filler dipstick back in place then unscrew and remove it to check the oil level Refer fig 5 The oil level is correct when it is at the full mark on the dipstick DO NOT OVERFILL Refer fig 5 Fuel Type Always use clean fresh unleaded petrol Purchase fuel Fig 4 in quantities that can be used within 30 days Never mix oil with petrol For added engine protection Briggs amp Stratton recommend the use of their fuel additive which is available from an authorised Briggs amp Stratton service dealer Fill to base of neck to allow for fuel expansion Do not overfill the fuel tank Refer fig 6 Fig 5 Fig 6 OPERATING THE MOWER Controls Operate all control levers several times and ensure that the cables move freely Check that the engine stop and ground drive clutch levers return freely to their rest position when released Refer fig 7 IMPORTANT To avoid damage
26. uld be mown without collecting the clippings If collection is required first mow the area without the grassbag at the maximum height of cut setting Allow the grass clippings to dry out and then mow the area at the maximum height of cut setting with the grassbag fitted Reduce the height of cut and mow the area again as necessary until the required finish is obtained To prevent damage to your lawn do not remove more than one third of grass height in one cut Refer fig 18 Blade Brake Clutch A device in the blade brake clutch helps minimise damage to the cutting mechanism when a hidden obstruction or overload is encountered When the obstruction or overload is removed the device will automatically reset Refer fig 19 Always stop the engine when a hidden obstruction or excessive vibration is encountered Disconnect the spark plug lead and examine the cutting mechanism ALWAYS replace a damaged cutterblade Refer to Maintenance Non Grassed Areas When moving the mower across non grassed areas stop the cutterblade and set the mower to the maximum height of cut to protect the cutting mechanism MAINTENANCE SCHEDULE MOWER MAINTENANCE Maintenance Schedule Follow the hourly or calendar intervals whichever occurs first More frequent service will be required if working for prolonged periods under dusty dry conditions or when airborne debris is present or after extensive operation cutting tall dry grass First 5
27. y be adjusted by operating the variable speed control Push forward to slow down and pull back to speed up Only operate the lever with the engine running to prevent damage If the blade stop lever is released the blade will stop Ref fig 10 To stop the engine pull the throttle lever to the stop posi tion Ref fig 10 amp 11 Reverse Travel Release the ground drive clutch lever Hold and pull against the handlebar with both hands to reverse the mower Turning A To make a wide turn steer the mower with the handlebar in the direction required To make a tight turn release the ground drive clutch lever apply downward pressure on the handlebar to raise the front wheels just above ground level and steer in the required direction To prevent accidents do not raise the front of the mower excessively when making a turn Never raise the rear of the mower when the engine is running Stopping A Release the ground drive clutch lever and release the engine stop lever Reduce throttle setting during engine shutdown Emergency stop Release both ground drive clutch lever and blade stop lever together If the engine fails to stop disconnect the spark plug lead Refer fig 12 Fig 12 OPERATING THE MOWER Slopes A To prevent engine damage do not use the mower on slopes greater than 20 degrees Refer fig 13 Height Of Cut To adjust the height of cut Grip the lever and pull side ways to disengage it from the lockin
Download Pdf Manuals
Related Search