Hayter Mowers 445E Lawn Mower User Manual
Contents
1. All Rights Reserved Safety Improperly using or maintaining this mower can result in injury To reduce the potential for injury comply with these safety instructions This mower was designed and tested for reasonably safe service however failure to comply with the following instructions may result in personal injury To ensure maximum safety best performance and to gain knowledge of the product it is essential that you and any other operator of the mower read and understand the contents of this manual before the engine is ever started Pay particular attention to the safety alert symbol Figure 2 which means Caution Warning or Danger personal safety instruction Read and understand the instruction because it has to do with safety Failure to comply with the instruction may result in personal injury General Lawn Mower Safety The following instructions have been adapted from the ISO 5395 This cutting machine is capable of amputating hands and feet and throwing objects Failure to observe the following safety instructions could result in serious injury or death Training Read the instructions carefully Be familiar with the controls and the proper use of the equipment Never allow children or people unfamiliar with these instructions to use the mowet Local regulations can restrict the age of the operator Keep in mind that the operator or user is responsible for accidents or hazards occurring to ot2. 8 HAYTER ne ENEN MAKERS OF THE FINEST MOWERS HAYTER LIMITED Operator s Manual R48 Recycling Mower Code 445E 446E 447E Uns No 280R00001 280500001 or 280T00001 and Manual Part No 111 2087 Rev B Introduction Read this information carefully to learn how to operate and maintain your product properly and to avoid injury and product damage You are responsible for operating the product properly and safely Whenever you need service genuine parts or additional information contact an Authorized Service Dealer and have the model and serial numbers of your product ready Figure 1 identifies the location of the model and serial numbers on the product 6008075 Figure 1 1 Model and serial number plate This manual identifies potential hazards and has safety messages identified by the safety alert symbol Figure 2 which signals a hazard that may cause serious injury or death if you do not follow the recommended precautions Figure 2 1 Safety alert symbol This manual uses 2 words to highlight information Important calls attention to special mechanical information and Note emphasizes general information worthy of special attention 2008 Hayter Limited Contents A ee 2 SUMEN dos 3 General Lawn Mower Safety nahe 3 Sound PESE ieun a a 4 Sound Power aos 4 Vibration ein 4 Safety and Instructional Decals A Denk Deine 6 Unfolding the
3. Figure 25 2 Plug the charger into a wall outlet Note When the battery no longer holds a charge dispose of the lead acid battery Replacing the Fuse Model 447E Only If the battery does not charge or the engine does not run with the electric starter the fuse may be blown Replace it with a 40 amp plug in type fuse Refer to Installing the Fuse 15 Drive System Maintenance Adjusting the Self propel Drive If your mower does not self propel properly adjust the self propel drive cable 1 Loosen the nut on the cable mount Figure 26 6006622 Figure 26 1 Nut on cable mount 2 Pullthe upper handle back fully rearward Figure 27 6006740 Figure 27 3 Pullthe cable jacket downward until you remove the slack in the exposed cable Figure 28 6006623 Figure 28 1 Exposed cable 4 Push the cable jacket upward 3 16 inch 5 mm Figure 29 1 A 9006624 Figure 29 1 Cable mount 2 Cable jacket Note You can place a ruler against the upper side of the cable mount and measure how far the upper end of the cable jacket moves Note Moving the cable jacket upward decreases the ground speed moving the jacket downward increases the ground speed Figure 30 N 7 ONN G006745 Figure 30 1 Cable jacket 5 Tighten the nut firmly 6 Start the mower and check the adjustment repeat this procedure if necessary 16 Blade
4. damage For best performance install a new blade before the cutting season begins Replace the blade when necessary with a genuine replacement blade Cutting Grass Cut only about a third of the grass blade at a time Do not cut below the 51 mm setting unless the grass is spatse or it is late fall when grass growth begins to slow down Refer to Adjusting the Cutting Height When cutting grass over 15 cm tall mow at the highest cutting height setting and walk slower then mow again at a lower setting for the best lawn appearance If the grass is too long the mower may plug and cause the engine to stall e Mow only dry grass or leaves Wet grass and leaves tend to clump on the yard and can cause the mower to plug or the engine to stall 11 Wet grass or leaves can cause serious injury if you slip and contact the blade Mow only in dry conditions Alternate the mowing direction This helps disperse the clippings over the lawn for even fertilization e If the finished lawn appearance is unsatisfactory try one or more of the following Replace the blade or have it sharpened Walk at a slower pace while mowing Raise the cutting height on your mower Cut the grass more frequently Overlap cutting swaths instead of cutting a full swath with each pass Set the cutting height on the front wheels one notch lower than the rear wheels For example set the front wheels at 60 mm and
5. read the 4 Cutting dismemberment Operator s Manual hazard of hand or foot stay away from moving parts 2 Cutting dismemberment 5 Thrown object hazard of hand or hazard keep deflector in foot remove the place spark plug lead before performing any maintenance on the machine 3 Thrown object hazard keep bystanders a safe distance from the machine 110 7058 1 Height of cut 110 7059 110 7059 Model 447E only 1 Read the Operator s 4 Install the fuse Manual 2 Remove the fuse box 5 Replace the fuse box decal cover 3 Remove the fuse box 6 Start the engine cover XN n 110 7178 110 7178 1 Height of cut Setup Unfolding the Handle 1 Unlock the handle locks move the handle sections into the operating position and lock the handle locks Figure 3 G008076 Figure 3 2 Unlock the upper handle locks and rotate the upper handle upward and lock it into a position that is comfortable to you Figure 4 M E 2 G005450 Figure 4 1 Highest position 3 Lowest position 2 Middle position Note You can set the upper handle to 1 of 3 handle positions Line up the mark to one of the 3 marks on the inner side of the upper handle locks Figure 4 Note If a handle lever is loose open the lever rotate it clockwise 1 or 2 turns to tighten it then close the lever Figure 5 6005475 Ga Figure 5 F
6. API service classification of SE SG SH SJ SL or higher 3 Install the dipstick Adjusting the Cutting Height Adjusting the cutting height may bring you into contact with the moving blade causing serious injury Stop the engine and wait for all moving parts to stop Do not put your fingers under the housing when adjusting the cutting height If the engine has been running the muffler will be hot and can severely burn you Keep away from the hot muffler Adjust the cutting height as desired Set all four wheels to the same height Note To raise the mower move the 2 cutting height levers forward to lower the mower move them both rearward Figure 11 p 2 FL 6008081 Figure 11 Starting the Engine 1 Firmly push in the primer 3 times with your thumb holding the primer in for a second before releasing it each time Figure 12 7 G008082 Figure 12 Note If the air temperature is below 13 C firmly push the primer in 5 times 2 Hold the blade control bar against the handle Figure 13 G005457 Figure 13 3 Pull the recoil starter Figure 14 or turn the ignition key as shown in Figure 15 model 447E only G005458 Figure 14 Important When you release the blade control bar both the engine and blade should stop amp within 3 seconds If they do not stop properly stop using your mower immediately and contact an Authorized Service Dealer R
7. Handle aan 6 Filling the Engine with Olsen 6 Installing the Fuse Model 447E Only 7 Charging the Battery Model 447E Only 7 Product Overview eio 8 Operation dep RE 8 Falling the Fuel Tank anal 8 Checking the Engine Oil Level 8 Adjusting the Cutting Height inei pte en 9 the Engine ur 9 Using the Self propel Drive Models 446E and A aig 10 Stopping the Eno een 10 Recycling the Clippings a 10 Bagging the Clippinss iss 10 Rear discharging the 11 Op raino ips 11 RE ERN 13 Recommended Maintenance Schedule s 13 Premaintenance Procedutesa asus vxo dba woe ue 13 Preparing for Maintenance eee cos ee ere 19 A er 14 Lubricating the Wheel ss 14 Engine Maintenances Ra 14 Replacing the Air Filtra 14 Changing the Engine Oil a 14 Electrical System Maintenance 15 Charging the Battery Model 447E pulo 15 Replacing the Fuse Model 447E Only 15 Drive System Maintenance nee 16 Adjusting the SelE propel Drive 16 Blade Maintenance 17 Replacing the Blade sanken 17 A tefte rie 18 Cleanto the Mowers aaa 18 LOLA DG EN 18 Preparing the Mower for Storage 18 Removing the Mower from Storage 18 Printed in the USA
8. Maintenance Replacing the Blade Service Interval Every 25 hours Replace the blade ot have it sharpened mote frequently if the edge dulls quickly Important You will need a torque wrench to install the blade properly If you do not have a torque wrench or are uncomfortable performing this procedure contact an Authorized Service Dealer Examine the blade whenever you run out of petrol If the blade is damaged or cracked replace it immediately If the blade edge is dull or nicked have it sharpened or replace it The blade is sharp contacting the blade can result in serious personal injury Wear gloves when servicing the blade 1 Disconnect the spark plug lead from the spark plug Refer to Preparing for Maintenance 2 Tip the mower onto its side with the air filter up Figure 31 G005386 Figure 31 3 Remove the blade saving all mounting hardware 4 Install the new blade and all mounting hardware Important Position the curved ends of the blade to point toward the mower housing 5 Use a torque wrench to tighten the blade bolt to 82 Nm 17 Important A bolt torqued to 82 N m is very tight While holding the blade with a block of wood put your weight behind the ratchet or wrench and tighten the bolt securely This bolt is vety difficult to overtighten Cleaning Cleaning the Mower Service Interval Before each use or daily Clean the mower Tipping the mower may cause
9. not tilt mower when starting the engine or switching on the motor unless the mower has to be tilted for starting In this case do not tilt it more than absolutely necessary and lift only the part which is away from the operator Start the engine or switch on the motor carefully according to instructions and with feet well away from the blade s and not in front of the discharge chute Operation e Never mow while people especially children or pets are nearby e Mow only in daylight or in good artificial light Stay alert for holes in the terrain and other hidden hazards Do not put hands or feet near or under rotating parts Keep clear of the discharge opening at all times Never pick up or carry a lawn mower while the engine is running Use extreme caution when reversing or pulling a pedestrian controlled lawn mower towards you Walk never run Slopes Do not mow excessively steep slopes Exercise extreme caution when on slopes Mow actoss the face of slopes never up and down and exetcise extreme caution when changing direction on slopes Always be sure of your footing on slopes Use low throttle settings when engaging the traction clutch especially in high gears Reduce speed on slopes and in sharp turns to prevent overturning or loss of control Stop the blade if the lawn mower has to be tilted for transportation when crossing surfaces other than grass and when transporting
10. old air filter Figure 23 G008086 Figure 23 3 Install a new air filter and the air filter cover Changing the Engine Oil Service Interval After the first 5 hours Change the engine oil Every 50 hours Change the engine oil Run the engine a few minutes before changing the oil to warm it Warm oil flows better and carries more contaminants 1 Perform the pre maintenance procedures refer to Preparing for Maintenance 2 Remove the dipstick Figure 6 3 Tip the mower onto its side with the air filter up to drain the used oil out through the oil fill tube Figure 24 ER N MESE 6008086 Figure 24 4 Slowly pour oil into the oil fill tube until the oil level reaches the Full line on the dipstick Figure 6 Do not overfill Max fill 0 59 1 type SAE 30W detergent oil with an API service classification of SE SG SH SJ SL or higher Install the dipstick securely Dispose of the used oil properly at a local recycling center Electrical System Maintenance Charging the Battery Model 447E Only Service Interval Every 25 hours Charge the battery for 24 hours Model 447E only Always use the charger in a sheltered area and charge the battery at room temperature 22 C whenever possible 1 Connect the charger to the mower wire harness located below the ignition key Figure 25 G002889
11. amaged parts for safety e Replace faulty silencers If the fuel tank has to be drained do this outdoors Do not change the engine governor settings or overspeed the engine Operating an engine at excessive speed can increase the hazard of personal injuty On multibladed lawn mowers take care as rotating one blade may cause others to rotate e Be careful during adjustment of the lawn mower to prevent entrapment of the fingers between moving blades and fixed parts of the lawn mowet To ensure the best performance and safety purchase only genuine replacement parts and accessories Do not use will fit parts and accessories they may cause a safety hazard Sound Pressure This unit has an equivalent continuous A weighted sound pressure level at the operator ear of 85 dBA based on measurements of identical machines per EN ISO 11201 and EN 836 Sound Power This unit has an equivalent continuous A weighted sound power level of 96 dBA based on measurements of identical machines per ISO 11094 Vibration Hand arm This unit does not exceed a hand arm vibration level of 4 9 m s based on measurements of identical machines per EN 1033 and EN 836 Safety and Instructional Decals Important Safety and instruction decals are located near areas of potential danger Replace damaged decals Manufacturer s Mark 1 Indicates the blade is identified as a part from the original machine manufacturer 1 Warning
12. ation concerning this written warranty or assistance in obtaining services lease write to HAYTER LIM ITED Service Department Spellbrook Bishop s Stortford ertfordshire CM 23 4BU UK ONLY Details of your local Hayter authorised dealer are contained in Yellow Pages and the Hayter website www hayter co uk or contact Freephone 0800 616298 Issue 12 08 03 CUSTOMER INFORMATION Code Serial No Date of Sale Your Local Dealer HAYTER LIMITED SPELLBROOK BISHOP S STORTFORD HERTS CM23 4BU ENGLAND
13. ction washers blade brake clutch B B C units and other such devices are not applicable Only machines fitted with a genuine Hayter friction disc which are used in accordance with the recommended operating and maintenance procedures are covered This warranty does not apply to any unit that has been tampered with altered misused abused or used for hire and will become invalid if non genuine Hayter parts are fitted This warranty does not cover minor mechanical adjustments unless they are due to defective material or workmanship Consult the Owner s Handbook or a Hayter Authorised Service Dealer for assistance when making these adjustments A warranty period of 90 days applies to machines used for commercial purposes To make a warranty claim return the unit to a Hayter authorised dealer along with proof of purchase stating the machine serial number and date of purchase The service receipt s or this Owners Handbook with the 1st 2nd year service boxes fully completed must be produced as proof of entitlement to the extended warranty period Subject to the conditions and exclusions in this limited warranty the authorised dealer will at our option repair or replace any warranted part within the duration of the warranty period This limited warranty gives you specific legal rights and is in addition to any statutory rights to which you may be entitled and your statutory rights are not affected by this warranty If you need additional inform
14. e hand fuel pump to remove the fuel Always tip P r oced S the mower onto its side with the air filter up Preparing for Maintenance Tipping the mower may cause the fuel to leak 1 Stop the engine and wait for all moving parts to stop Petrol is flammable explosive and can cause 2 Disconnect the spark plug lead from the spark plug personal injury Figure 21 before performing any maintenance Run the engine dry or remove the petrol with a procedure hand pump never siphon G008085 Figure 21 3 After performing the maintenance procedure s connect the spark plug lead to the spark plug Important Before tipping the mower to change the oil or replace the blade allow the fuel tank to run dry through normal usage If you must tip the mower prior to running out of fuel use a 13 Lubrication Lubricating the Wheel Gears Service Interval Yearly Lubricate the wheel gears 1 Remove the wheel bolts on the rear wheels and remove the rear wheels 2 Apply a lubricating oil to the gear as shown in Figure 22 x _6 amp Ecce NE in AN NC G005456 Figure 22 3 Install the rear wheels 14 Engine Maintenance Replacing the Air Filter Service Interval Yearly Replace the air filter more frequently in dusty operating conditions Perform the pre maintenance procedures refer to Prepating for Maintenance Open the air filter cover and remove the
15. ecycling the Clippings Your mower comes from the factory ready to recycle the grass and leaf clippings back into the lawn 6005459 Figure 15 Note The grass bag may remain on the mower while you are recycling the clippings 4 If the mower does not start in 1 or 2 pulls or within 5 seconds using the electric starter press the primer button 1 or 2 times and try starting it again To recycle the clippings move the Recycling bagging lever to the recycling mode Figure 18 Note If the mower still does not start contact an Lern Authorized Service Dealer e ne 2 N Using the Self propel Drive TL NU EB Models 446E and 447E Only 18 To operate the self propel drive simply walk with your Ber hands on the upper handle and your elbows at your sides and the mower will automatically keep pace with Figure 18 you 1 Recycling mode 2 Bagging mode Bagging the Clippings Use the grass bag when you want to collect grass and leaf clippings from the lawn Figure 16 A worn grass bag could allow small stones and other similar debris to be thrown in the operator s or bystander s direction and result in Stopping the Engine serious personal injury ot death to the operator 1 Release the blade control bar Figure 17 or bystandets Check the grass bag frequently Ifit is damaged install a new Hayter replacement bag The blade is sharp contacting the blade can LIE result in serious pe
16. her people or their property Understand explanations for all pictograms used on the mower or in the instructions Petrol WARNING Petrol is highly flammable Take the following precautions Store fuel in containers specifically designed for this purpose Refuel outdoors only and do not smoke while refueling e Add fuel before starting the engine Never remove the cap of the fuel tank or add petrol while the engine is running or when the engine is hot e If petrol is spilled do not attempt to start the engine but move the mower away from the area of spillage and avoid creating any source of ignition until petrol vapots have dissipated e Replace all fuel tank and container caps securely Preparation e While mowing always wear substantial footwear and long trousers Do not operate the equipment when barefoot or wearing open sandals Thoroughly inspect the area where the equipment is to be used and remove all stones sticks wires bones and other foreign objects Before using always visually inspect to see that guatds and safety devices such as deflectors and or grass bags are in place and working correctly e Before using always visually inspect to see that the blades blade bolts and cutter assembly are not worn or damaged Replace worn or damaged blades and bolts in sets to preserve balance Starting e Disengage all blade and drive clutches and shift into neutral before starting the engine Do
17. il throughout the cylinder to prevent cylinder corrosion during the off season 7 Loosely install the spark plug 8 Tighten all nuts bolts and screws 9 Charge the battery for 24 hours model 447E then unplug the battery charger and store the mower in an unheated area If you must store the mower in a heated area charge the battery every 90 days Removing the Mower from Storage 1 Remove the spark plug and spin the engine rapidly using the starter to blow the excess oil from the cylinder 2 Install the spark plug and tighten it with a torque wrench to 20 N m Charge the battery for 24 hours model 447E only 4 Connect the lead to the spark plug 18 Notes Notes HAYTER HAYTER MAKERS OF THE FINEST MOWERS Em MAKERS OF THE FINEST MOWERS 1st Year 12 months 1st Year 12 months Owner s Name We certify that this service has been carried out by an Authorised Hayter Service Dealer Serial Number Date Date Note for dealer Please retain this voucher for your records HAYTER HAYTER Emm MAKERS OF THE FINEST MOWERS MAKERS OF THE FINEST MOWERS 2nd Year 24 months 2nd Year 24 months Owner s Name We certify that this service has been carried out by an Authorised Hayter Service Dealer Serial Number Date Date Note for dealer Please retain this voucher for your records LIMITED WARRANTY Hayter Limited warrants t
18. illing the Engine with Oil Your mower does not come with oil in the engine 1 Remove the dipstick Figure 6 6008077 Figure 6 N Slowly pour oil into the oil fill tube until the oil level reaches the Full line on the dipstick Figure 6 Do not overfill Max fill 0 59 1 type SAE 30W detergent oil with an API service classification of SF SG SH SJ SL or higher 3 Install the dipstick securely Important Change the engine oil after the first 5 operating hours change it yearly thereafter Refer to Changing the Engine Oil Installing the Fuse Model Charging the Battery Model 447E Only 447E Only Your mower comes with a 40 amp fuse that protects the Refer to Charging the Battery in the Maintenance electric starter section Important You cannot start the mower with the electric starter or charge the battery unless you install the fuse 1 Remove the battery cover and the battery and locate the fuse holder Figure 7 6005388 X Figure 7 1 Screw 3 Fuse holder 2 Battery cover 4 Battery 2 Insert the fuse from the loose parts bag into the fuse holder Figure 8 lt 9 G002878 Figure 8 Note Your mower comes with a fuse in the owner s packet and another fuse in the battery box 3 Install the battery and the battery cover Product Overview Operation Filling the Fuel Tank Petrol is extremely flammable and explosive A fire or explosion from petrol can burn y
19. o the original user purchaser that this unit shall be free from defects in material and workmanship under normal use and service for a period of three years from the date of purchase The manufacturer of major proprietry components ie engines gearbox transaxle where applicable furnish their own warranty and services are provided through their authorised network To qualify for the full benefit of the warranty the warranty registration card must be returned within 14 days of purchase Subject to the conditions and exclusions noted in this limited warranty we shall at our option repair or replace any warranted part during the applicable period If you are in doubt or experience any difficulty please consult a Hayter Authorised Service Dealer for clarification To qualify for the extended warranty second and third year of the three year limited warranty the machine must have annual services carried out by an Authorised Hayter Service Dealer These chargeable services should be carried out within 12 and 24 months of the date of purchase Excluded from the extended warranty period are those items which are subject to normal wear and tear e g tyres wheels cutterblades belts cables grassbags brush bristles batteries and other consumable wearing parts All consumer machines which are fitted with a genuine Hayter friction disc as original equipment before use are covered by a Lifetime Warranty against the engine crankshaft bending Note fri
20. ou and others To prevent a static charge from igniting the petrol place the container and or mower directly on the ground before filling not in a vehicle or on an object Fill the tank outdoors when the engine is cold Wipe up spills Do not handle petrol when smoking or Figure 9 around an open flame or spatks Model 447E shown Store petrol in an approved fuel container 1 Lower handle lock 9 Oil fill Dipstick not shown out of the reach of children 2 Grass bag 10 Fuel tank cap Soo Upper Tidndie ded 11 Cutting height lever 2 Fill the fuel tank with fresh unleaded petrol Figure 10 4 Recoil start handle 12 Spark plug 5 Upper handle Models 13 Primer Important To reduce starting problems add 2s and Wis only e fuel stabilizer to the fuel all season mixing it with ade control bar Air filter 7 Electric start model 447E 15 Recycling bagging lever petrol less than 30 days old only 8 Rear door G008080 Figure 10 Checking the Engine Oil Level Service Interval Before each use or daily Check the engine oil level 1 Remove the dipstick wipe it clean and fully install the dipstick Figure 6 2 Remove the dipstick and check the oil level Figure 6 If the oil level is below the Add mark on the dipstick slowly pour oil into the oil fill tube to raise the oil level to the Full mark on the dipstick Do not overfill Max fill 0 59 1 type SAE 30W detergent oil with an
21. rsonal injury Figure 17 Stop the engine and wait for all moving parts to stop before leaving the operating position 2 When the engine stops remove the ignition key when you leave the mowet 10 To bag the grass clippings install the grass bag refer to Installing the Grass Bag and move the Recycling bagging lever to the bagging mode Figure 18 Installing the Grass Bag Raise and hold up the rear door install the bag and lower the rear door Figure 19 G008083 Figure 19 Removing the Grass Bag To remove the bag reverse the steps above Rear discharging the Clippings Use the rear discharge for cutting very tall grass If the bagis on the mower remove it refer to Removing the Grass Bag before rear discharging the clippings Figure 20 The Recycling bagging lever should be in the bagging mode G008084 Figure 20 The blade is sharp contacting the blade can result in serious personal injury Stop the engine and wait for all moving parts to stop before leaving the operating position Operating Tips General Mowing Tips Clear the area of sticks stones wire branches and other debris that the blade could hit Avoid striking solid objects with the blade Never deliberately mow over any object e Ifthe mower strikes an object or starts to vibrate immediately stop the engine disconnect the lead from the spark plug and examine the mower for
22. the fuel to leak from the carburetor or the fuel tank Petrol is extremely flammable highly explosive and under certain condition can cause personal injury or property damage Run the engine dry or remove the fuel with a hand pump never siphon the fuel 1 Perform the pre maintenance procedures refer to Preparing for Maintenance Remove the grass bag Drain the fuel from the fuel tank Tip the mower onto its side with the air filter up pe Remove the dirt grass clippings with hardwood or plastic scraper Avoid burrs and sharp edges Spray the underside of the mower housing with water Turn the mower upright after cleaning the mower Storage Store the mower in a cool clean dry place Preparing the Mower for Storage Petrol vapors can explode Do not store petrol more than 30 days Do not store the mower in an enclosure neat an open flame Allow the engine to cool before storing it 1 On the last refueling of the year add fuel stabilizer to the fuel as directed by the engine manufacturer 2 Run the mower until the engine stops from running out of fuel Prime the engine and start it again 4 Allow the engine to run until it stops When you can no longer start the engine it is sufficiently dry 5 Disconnect the lead from the spark plug 6 Remove the spark plug add 30 ml of oil through the spark plug hole and pull the starter rope slowly several times to distribute o
23. the lawn mower to and from the area to be mowed e Do not operate the engine in a confined space where dangerous carbon monoxide fumes can collect Stop the engine whenevet you leave the lawn mowet before refueling before removing the grass bag before making height adjustment unless adjustment can be made from the operator s position Stop the engine and disconnect the spark plug lead before clearing blockages or unclogging chute before checking cleaning ot working on the lawn mowet after striking a foreign object inspect the lawn mower for damage and make repairs before restarting and operating the lawn mower iflawn mowet starts to vibrate abnormally check immediately e Watch out for traffic when crossing or near roadways Maintenance and Storage Keep all nuts bolts and screws tight to be sure the equipment is in safe working condition Do not use pressure cleaning equipment on machine Never store the equipment with petrol in the tank and inside a building where fumes can reach an open flame or spark Allow the engine to cool before storing in any enclosure To reduce the fire hazard keep the engine silencer battery compartment and petrol storage area free of grass leaves or excessive grease e Check grass bag components and the discharge guard frequently and replace with manufacturer s recommended parts when necessary Replace worn or d
24. the rear wheels at 70 mm Cutting Leaves After cutting the lawn ensure that half of the lawn shows through the cut leaf cover You may need to make more than one pass over the leaves are more than 13 cm of leaves on the lawn set the front cutting height one or two notches higher than the rear cutting height Slow down yout mowing speed if the mower does not cut the leaves finely enough Maintenance Recommended Maintenance Schedule s Maintenance Servi ce S Maintenance Procedure Interval After the first 5 hours Change the engine oil Check the engine oil level Before each use or daily Ensure that the engine stops within 3 seconds after releasing the blade control bar Clean the mower E 25h Charge the battery for 24 hours Model 447E only very ours Replace the blade or have it sharpened more frequently if the edge dulls quickly Every 50 hours Change the engine oil Clean the cooling system refer to your engine owner s manual Every 100 hours Replace the spark plug refer to your engine owner s manual Before storage Empty the fuel tank before repairs as directed and before annual storage Lubricate the wheel gears Replace the air filter more frequently in dusty operating conditions Check the spark plug refer to your engine owner s manual Refer to your Engine Operator s Manual for any additional yearly maintenance procedures P rema ten anc
Download Pdf Manuals
Related Search