Global Machinery Company LT550 Trimmer User Manual
Contents
1. 2 If the line is to short push down on the automatic feed spool 10 and at the same time pull the line out so that it extends a few centimeters past the edge of the guard 3 Remove the cover from the line cutting blade 9 4 During operation to increase the cutting line simply switch the line trimmer off and then on again this with restore the line to the correct length Note Only remove the cover from the cutting line blade when all operational checks have been carried out Replace the cover when the line trimmer is not in use Switching on and off 1 Connect the extension cord to power 2 Press the lock off button 4 then press the trigger switch 3 3 To switch off release the trigger switch WARNING The tool runs for approximately 5 seconds after it has been switched off Let the motor come to a complete standstill before setting the tool down Trimming WARNING Make sure that the work area 1s free of rocks debris lines and other foreign objects 1 Start the trimmer before approaching the grass to be cut 2 The automatic line feed mechanism releases 12mm from each line when the trimmer reaches a certain speed If you need the spool to release more than 12mm of line per side release the trigger until the speed falls beyond the trigger point then press the switch again As the speed picks up a further 12mm will be released for both lines 3 Cut the grass by swinging the tnmmer fr2. When the machine is not in use store it in a dry place and out of reach of children After use disconnect the machine from the power supply and check for damage If you have the slightest doubts contact an authorised service centre Only use the machine according to the instructions given in this manual Check regularly that the screws are tight Do not try to repair the machine or access internal parts Contact authorised service centres only Do not get distracted and always concentrate on what you are doing Use common sense Never operate the machine when you are tired sick or under the influence of alcohol or other drugs Due to modern mass production techniques it is unlikely that your power tool 1s faulty or that a part 1s missing If you find anything wrong do not operate the tool until the parts have been replaced or the fault has been rectified Failure to do so could result in serious personal injury Contents of carton e Blade guard e Edging wheel e Secondary handle e 4 Screws and washers Know your product Before using the line trimmer familiarise yourself with all the operating features and safety requirements This line timmer is to be used for trimming soft new growth only Use the tool and accessones only for the applications intended All other applications are expressly ruled out 1 Extension cord securing hook 2 Handle 3 Trigger switch 4 Lock off button 5 Secondary handle 6 Tel
3. INSTRUCTION MANUAL 230W _ fF Line eX i T LE Trimmer j P YEAR REPLACEMENT WARRANTY 30 SATISFACTION GLOBAL MACHINERY COMPANY GUARANTEE Melbourne Perth Auckland Hong Kong Shanghai LTS 5 o Taipei New York Verona London Paris 050524 ED5 JJ Contents Introduction Environmental protection Description of symbols Specifications Safety instructions Additional safety rules for line trimmers Unpacking Contents of carton Know your product Assembly Before starting Increasing the cutting line Switching on and off Trimming Using as an edger Changing a line spool Maintenance and cleaning General inspection Storage Power cord maintenance IO 9190 4 CO N Sy BD OT BR amp G Lu 0o Ra MM h h Full 2 Years Home Use Warranty Whilst every effort is made to ensure your complete satisfaction with this tool occasionally due to the mass manufacturing techniques a tool may not live up to our required level of performance and you may need the assistance of our service department This product is warranted for a 2 year period for home domestic use from the date of the original purchase If found to be defective in materials or workmanship the tool or the offending faulty component will be replaced free of charge with another of the same item A small freight charge may apply The warranty replacement unit is only made
4. available by returning the tool to the place of purchase with a confirmed register receipt Proof of purchase is essential We reserve the right to reject any claim where the purchase cannot be verified This warranty does not include damage or defects to the tool caused by or resulting from abuse accidents alterations or commercial or business use It also does not cover any bonus accessories unless the tool is a GMC Platinum Professional model Please ensure that you store your receipt in a safe place Conditions apply to the above warranty If you need direction of what constitutes a free of charge warranty claim please review the guide given on the rear of the Receipt Holder An indication is given as to the types of claim that are permissible and those that are not Dear Customer If you require any help with your product whether it is a Warranty claim spare part or user information please phone our Help Line for an immediate response Phone 1300 880 001 in Australia or 0800 445 721 in New Zealand Introduction Your new GMC power tool will more than satisfy your expectations It has been manufactured under stringent GMC Quality Standards to meet superior performance critena You will find your new tool easy and safe to operate and with proper care it will give you many years of dependable service CAUTION Carefully read through this entire Instruction Manual before using your new GMC Power Tool Take special car
5. e to heed the Cautions and Warnings Your GMC power tool has many features that will make your job faster and easier Safety performance and dependability have been given top priority in the development of this tool making it easy to maintain and operate Environmental protection as Recycle unwanted matenals instead of disposing of them as waste All tools hoses d and packaging should be sorted taken to the local recycling centre and disposed of in an environmentally safe way Description of symbols The rating plate on your tool may show symbols These represent important information about the product or instructions on its use Wear hearing protection Wear eye protection Wear breathing protection Double insulated for additional protection Is Conforms to relevant standards for electromagnetic compatibility w eo Use at a distance of at least 5m from other people If cordset is damaged remove it from the plug immediately and have it replaced by an authorised service centre Do not use in the rain gt e cause severe injury a sg Thrown objects and rotating line can Dr DJ Sharp blade Specifications Voltage 230 240Vac 50Hz Input power 550W No load speed 11 000 min Cut diameter swathe 320mm Line thickness 1 2mm Spool type Automatic Feed Sound pressure level 96dB A Tool weight 3 4kq Safety instructions WARNING Read and unde
6. escopic shaft 7 Inmming head 8 Guard 9 Line cutting blade 10 Automatic feed spool 11 Spool button 12 Edging wheel 13 Telescopic shaft adjustment knob 14 Handle rotating button 15 Handle adjustment pedal Assembly Fitting the secondary handle 1 Hold in the secondary handle buttons and push the handle E over them Fitting the guard and guide wheel 1 Align the 4 screw holes in the guard 8 with the screw holes in the base of the unit 2 To adjust the secondary handle press in the secondary p handle buttons and rotate d the handle to the desired position then release the buttons to lock it into place Extension cord support There is a hole in the back of the handle of the line trimmer which is used as an extension cord retention device To avoid detaching the extension cord always check that it is attached firmly during use 2 Place the edging wheel over the 2 screw holes at the front section of the guard 3 Locate the 4 screws and washers and tighten them with a screwdriver 1 Make a loop in the extension cord and push it through the square hole in the back of the handle Note Always ensure the cutting line blade guard 9 is fitted to the cutter blade whenever carrying out maintenance on the line trimmer 2 Place the end of the loop around the securing hook 1 and pull back on the cord so it is firmly held in place Vertical handle adjustment The handle can be adjus
7. et is damaged or worn it must be replaced by the manufacturer or service agent or a similarly qualified person in order to avoid a hazard 6 Never use caustic agents to clean plastic parts CAUTION Do not use cleaning agents to clean the plastic parts of the tool A mild detergent on a damp cloth is recommended Water must never come into contact with the tool 11 General inspection Regularly check that all the fixing screws are tight They may vibrate loose over time Storage 1 Store the trimmer away from direct sunlight 2 Do not store in a nylon bag as this can encourage the formation of mould 3 At the end of the season give the trimmer an overall cleaning and a thorough check 4 Do not leave the trimmer resting on the floor for extended periods as it could cause the shape of the guard to alter posing a safety nsk Hang it off the floor by the top handgnp Power cord maintenance If the supply cord needs replacing the task must be carried out by the manufacturer the manufacturer s agent or an authorised service centre in order to avoid a safety hazard Carefully read the entire Instruction Manual before using this product Before returning this product for a With continuing product development changes may Warranty Claim or any other reason have occurred which render the product received slightly different to that shown in this instruction Please Call 1300 880 001 Austr alia manual The manufact
8. facilities ensure that these are connected and properly used Use of these devices can reduce dust related hazards Power tool use and care Do not force the power tool Use the correct power tool for your application The correct power tool will do the job better and safer at the rate for which 1t was designed e Do not use the power tool if the switch does not turn it on and off Any power tool that cannot be controlled with the switch is dangerous and must be repaired Disconnect the plug from the power source before making any adjustments changing accessories or storing power tools Such preventive safety measures reduce the risk of starting the power tool accidentally Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool Power tools are dangerous in the hands of untrained users Maintain power tools Check for misalignment or binding of moving parts breakage of parts and any other condition that may affect the power tool s operation If damaged have the power tool repaired before use Many accidents are caused by poorly maintained power tools Keep cutting tools sharp and clean Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control Use the power tool accessories and tool bits etc in accordance with these instructions and in the manner intended for the partic
9. heel is used to guide the line trimmer along the ground Changing a line spool Warning Ensure the cutting line blade cover is replaced Note Always unplug the trimmer before carrying out any maintenance or making any adjustments to the line trimmer 1 Tum the line trimmer upside down 2 Hold the spool holder firmly with one hand and with the other hand squeeze the tabs on either side of the spool cover and remove the cover 3 Remove the empty spool and clean out the spool cover 4 Align the cutaway sections in the spool opposite the eyelets and thread the two lines of the or new spool through the two eyelets in the spool holder and insert the spool 5 Press the auto feed spool 10 and pull out the lines until they reach the outside edge of the guard 6 Replace the spool cover ensuring that it is fully inserted CAUTION After changing the line spool run the trimmer under no load for at least a minute to make sure that the line and the tool are both operating correctly Use only the line spool as recommended by the manufacturer Maintenance and cleaning 1 Store the tool instruction manual and accessones in a secure dry place In this way you will always have the information ready to hand 2 Keep the tool s air vents unclogged and clean at all times 3 Remove dust and dirt regularly Cleaning is best done with a rag 4 All bearings and bushes are lubricated for life 5 If the cords
10. om right to left and proceed slowly keeping the trimmer inclined forwards at an angle of about 30 Light cuts are better than heaw cuts as they allow the cut grass to fall away from the spool preventing the grass from clogging the spool 4 Start cutting nearest the mains power source and work away from it to make it easier to avoid the extension cord 5 High grass should be cut in layers always beginning from the top Do not cut damp or wet grass Do not overload your trimmer 6 Avoid wearing the line out quickly by knocking against hard objects stones walls fences etc 7 Watch out for kickbacks in the event of impact with hard objects 8 After finishing the cutting operation keep the head close to ground level release the switch and allow the motor to come to a complete standstill Place the trimmer on the ground switch off and remove the cable plug from the mains supply Note Periodically clean out the grass between the spool and the rim of the guard to prevent the tool from vibrating Using as an edger Note Always unplug the trimmer before carrying out any maintenance or making any adjustments to the line trimmer 1 Press the handle rotating button 14 and rotate the shaft 180 degrees so it is facing so the handle is facing the opposite direction 2 Release the rotating button 14 ensuring that the handle clicks into position 10 3 You can now use the line trimmer as an edger The w
11. operating a power tool outdoors use an outdoor extension cord suitable for outdoor use Use of a cord suitable for outdoor use reduces the risk of electric shock Personal safety e Stay alert watch what you are doing and use common sense when operating a power tool Do not use a power tool while you are tired or under the influence of drugs alcohol or medication A moment of inattention while operating power tools may result in serious personal injury Use safety equipment Always wear eye protection Safety equipment such as a dust mask non skid safety shoes hard hat or hearing protection used for appropriate conditions will reduce personal injuries Avoid accidental starting Ensure the switch is in the off position before plugging in Carrying power tools with your finger on the switch or plugging in power tools that have the switch on invites accidents e Remove any adjusting key or wrench before turning the tool on A wrench or a key that is left attached to a rotating part of the power tool may result in personal injury Do not overreach Keep proper footing and balance at all times This enables better control of the power tool in unexpected situations e Dress properly Do not wear loose clothing or jewellery Keep your hair clothing and gloves away from moving parts Loose clothes Jewellery or long hair can be caught in moving parts e If devices are provided for the connection of dust extraction and collection
12. rstand all instructions Failure to follow all instructions listed below may result in electric shock fire and or serious injury The term power tool in all of the wamings below refers to your mains operated corded power tool or battery operated cordless power tool Save these instructions Work area e Keep work area clean and well lit Cluttered and dark areas invite accidents e Do not operate power tools in explosive atmospheres such as in the presence of flammable liquids gases or dust Power tools create sparks which may ignite the dust or fumes e Keep children and bystanders away while operating a power tool Distractions can cause you to lose control Electrical safety e Power tool plugs must match the outlet Never modify the plug in any way Do not use any adapter plugs with earthed grounded power tools Unmodified plugs and matching outlets will reduce nsk of electric shock Avoid body contact with earthed or grounded surfaces such as pipes radiators ranges and refrigerators There is an increased risk of electric shock if your body is earthed or grounded Do not expose power tools to rain or wet conditions Water entering a power tool will increase the nsk of electric shock Do not abuse the cord Never use the cord for carrying pulling or unplugging the power tool Keep cord away from heat oil sharp edges or moving parts Damaged or entangled cords increase the risk of electric shock e When
13. ted so that it at horizontal with the ground this feature helps you get access to areas such as under bushes and garden furniture The handle can be lowered by pressing down on the handle Adjusting the telescopic handle 1 Push the telescopic shaft adjustment knob 13 and hold adjust the shaft to a comfortable height Make sure the button clicks into position once the desired height has been selected 8 adjustment pedal 15 on the base of the line trimmer with your foot Then move the handle downwards to the desired angle Before starting Before use check that the tool is in good working order and that the length of the trimmer line is correct as follows 1 Ensure the switch is in the off position and disconnect the cable plug from the mains supply 2 Examine the general condition of the tool Inspect the guard switch cordset and extension cord Check for loose screws misalignment binding of moving parts improper mounting broken parts and any other condition that may affect its safe operation If abnormal noise or vibration occurs during operation tum the line trimmer off immediately and have the problem corrected 3 Ensure that you are on a flat surface and have secure footing 4 Check that the line touches or goes beyond the edge of the guard Increasing the cutting line 1 Before starting ensure the cutting line is the correct length Pull the cutting line to the edge of the guard 8
14. ts Turn it off if they get too close Maintain a safe distance of at least 5m from other people when using the machine e Keep a balanced and stable stance while using the machine Ensure that the area being cut is free from strings stones and debris e Do not cut against hard objects This could cause injury to the operator and damage to the machine e Never use the machine without the guard Never use the machine if the guard is damaged Wear goggles Wear ear defenders Wear a breathing mask Warning The guard is vital for your and other people s safety and for the machines operating efficiency e Do not try to stop the cutting device nylon line with your hands Always let it come to a stop by itself Unpacking Warning After switching off the machine the cutting device continues to rotate for a few more seconds Only use the original type of nylon line Under no circumstances use metal line instead of nylon Do not use the machine to cut grass which 1s not on the ground For example do not cut grass which is on walls or rocks Do not switch on the machine in enclosed or poorly ventilated spaces or in the presence of inflammable and or explosive substances such as liquids gasses and powders Only cut during broad daylight or with adequate artificial light Check that all grass cuttings and dirt have been removed from the ventilation vents Do not cross roads or gravel paths with the machine still running
15. ular type of power tool taking into account the working conditions and the work to be performed Use of the power tool for operations different from intended could result in a hazardous situation Service e Have your power tool serviced by a qualified repair personnel using only identical replacement parts This will ensure that the safety of the power tool is maintained Additional safety rules for line trimmers e Always wear adequate protective clothing when operating the machine to avoid injunes to face eyes hands feet head or heanng Use safety glasses or a face shield high boots or sturdy shoes long trousers work gloves a hard hat and hearing protection When starting up and when the machine is in operation keep the cutting section away from all parts of the body especially the hands and feet Do not start the machine when it is upside down or when it is not in the operating position Switch the motor off and pull out the plug when the machine is not being used left unattended being cleaned being moved from one place to another or when the spool is being changed or the length of line manually adjusted If there is an interruption to the power supply or the extension cable is damaged switch off the machine immediately and remove the plug from the power point Do not move the machine by pulling on the electrical cable Always use the handgnp Do not operate the machine near people especially children or pe
16. urer reserves the right to or 0800 445 721 New Zealand change specifications without notice Note Specifications may differ from country to country When you make your call please have the following information at hand e GMC Product Type GMC Product Code EV A 7 DAYS A WEEK 7AM Lu A GMC Service Engineer will take your call and in most cases will be able to solve your problem over The GMC 777 Helpline operates from 7am to the phone 7pm 7 days a week EST This allows you You are welcome to use this phone in service to to contact GMC directly with any queries and make suggestions or give comments about any technical questions you have regarding GMC product our products GM GLOBAL MACHINERY COMPANY 45 55 South Centre Road Melbourne Airport Victoria Australia 3045 Tel 03 8346 1100 Fax 03 8346 1200 Save this Manual for future reference REPLA WA
Download Pdf Manuals
Related Search