GE PTZ 12X Security Camera User Manual
Contents
1. gasket re attach the bubble to the camera body 5 Gently press down the bubble with two hands on the side of it Make sure the two slotted screws and the screw hole on the bubble align with the three holes on the camera housing DO NOT press on the top of the bubble 6 Screw the bubble and camera body together with the supplied M3 standard security screw TruVision Mini PTZ 12X Camera Pocket Guide 8 Further secure the bubble by turning the two slotted screws counterclockwise so that they touch the dome camera housing Set the DIP switches Setting up the camera To quickly put the Mini PTZ 12X camera into operation 1 Configure the camera s DIP switches which are located on the top of the camera Set the camera communication protocol Set the RS 485 communication DIP switch Set the camera ID Wire the camera Connect the camera to a monitor Mount the camera to the ceiling See the user manual for information Program the camera TruVision Mini PTZ 12X Camera Pocket Guide Camera DIP switches Configure the camera s ID and communication protocol before connecting the analog camera to other devices See Figure 1 for the location of the DIP switches in both the indoor and outdoor cameras Figure 1 Camera DIP switches Indoor camera Outdoor camera A Dome camera protoco2. the unit has a tolerance of 24 VAC 10 Do not overload the power cord or adapter TruVision Mini PTZ 12X Camera Pocket Guide e Ventilation Ensure that the location planned for the installation of the camera is well ventilated e Temperature Do not operate the camera beyond the specified temperature humidity or power source ratings The operating temperature of the indoor camera is between 0 C to 50 C 32 F to 122 F and that of the outdoor camera is between 30 C to 50 22 F to 122 F Humidity is below 90 e Moisture Do not expose the indoor camera to rain or moisture or try to operate it in wet areas The indoor camera is designed for indoor use or locations only where it is protected from rain and moisture Turn the power off immediately if the camera is wet and ask a qualified service person for servicing Moisture can damage the camera and also create the danger of electric shock e Cleaning Clean only with a dry cloth If the dirt is difficult to remove use a mild detergent and wipe gently Protect from strong light Never face the camera towards the sun Do not aim the camera at bright objects Whether the camera is in use or not never aim it at the sun or other extremely bright objects Otherwise the camera may be smeared or damaged e Servicing Do not attempt to service this unit yourself Any attempt to dismantle or remove the covers from this product will invalidate the warranty and may also
3. interface cable see Figure 4 This cable facilitates installation as there is only one cable to connect to the dome camera Figure 4 24 VAC I O interface cable h 1 Power input cable 4 RS 485 serial data connector 2 Video output cable 5 22 pin connector to 3 Alarm cable camera Note Power input to the camera has a tolerance of 24 VAC 10 Caution During installation carefully pull the cables so as not to damage them It is recommended to fasten the cables once they are connected TruVision Mini PTZ 12X Camera 13 Pocket Guide To wire the dome camera 1 14 Connect the 22 pin connector of the I O interface cable to its connector in the base of the dome camera See Figure 1 for its location Connect the crimp on BNC connector of the video output to the coaxial video cable of a monitor or DVR Connect the control keyboard to the dome camera through the serial terminal block Connect the alarm cable to a dry contact For example a PIR detector or an access control system Connect the RS 485 serial data connector to the DVR keypad as shown below Figure 5 2 wire connection from a DVR control keypad PC to the dome camera D 6 S D 6 Connect the power cable to the power source As soon as the dome camera is connected it is operational D R A Or 0 5 0 Note The ground wire must be inserted into the center pin of the power i
4. GE Security TruVision Mini PTZ 12 Camera Pocket Guide E P N 1069516 e REV A e ISS 010 09 Copyright 2009 GE Security Inc Content Introduction 2 Package contents 2 Installation environment 2 Example ofa system setup 4 Cable requirements 4 Removing the protective cover from the outdoor camera 6 Setting up the camera 8 Camera DIP switches 9 Setting the camera protocol 9 Setting the communication DIP switches 10 Setting the dome camera site ID 11 22 pin connector description 12 Wiring the dome camera 13 Main menu overview 15 Using a keypad to program menus 17 TruVision Mini PTZ 12X Camera Pocket Guide Introduction This pocket guide provides basic information on setting up and using the TruVision Mini PTZ camera Package contents The TruVision Mini PTZ camera is shipped with the following items Dome camera and 4 7 bubble Mounting accessories hard ceiling mount plastic fixing plate and screws I O interface cable for power video alarms and serial data TruVision Mini PTZ 12X Camera pocket guide TruVision Mini PTZ 12X Camera user manual on CD Installation environment When installing your camera consider these factors Handling Handle the camera carefully Avoid striking shaking etc Improper handing or storage could damage the camera Electrical Install electrical wiring carefully It should be done by qualified service personnel The input electricity to
5. e such as a control keypad to configure the camera menu options This manual uses the KTD 405 keypad controller to explain the features of the TruVision PTZ Mini 12X camera because of the KTD 405 s ability to control all of the camera s features For detailed keypad instructions refer to the KTD 405 KTD 405 2D Controller Keypad User Manual You can record the settings for the dome cameras using the checklist in User Manual This checklist also lists the default values of the settings where applicable To access the programming menus 1 Switch the keypad to the camera site you want to program 2 Press and hold the set key until Enter programming code displays 3 Atthe code entry display enter the programming code 9 5 1 Then press the seq button 4 Atthe first menu display press 3 to select the option Camera 5 Atthe Enter camera site number screen enter the site number of the camera you wish to program Camera default value is 1 The Main Page 1 menu appears Navigating the menus You can use the keypad keys and joystick to navigate through the menu system See the user manual for further information on their use TruVision Mini PTZ 12X Camera 17 Pocket Guide Table 4 Navigating the programming menus Key Function Il Scrolls up a menus gt Scrolls down a menu an G Scrolls left or right when indicated by gt in the menu set Enters or exits a menu or submenu when indicated by in a menu op
6. l DIP D 22 pin connector switches E Dome camera site ID DIP B RS 485 communication DIP switch switches F Reserved C None G Reserved Setting the camera protocol The dome camera can use different protocols for communication To select a protocol you must set the protocol DIP switches to the correct sequence of 1s on and Os off TruVision Mini PTZ 12X Camera 9 Pocket Guide To set the dome camera protocol 1 Locate the protocol DIP switch block A Figure 1 2 Set the DIP switch sequence for the desired protocol See Table 2 below for the most frequently used protocol settings For other supported protocols please refer to the user manual Table 2 Dome camera protocols supported Protocol Switch position GE Impac RS 485 HII Baud rate 9600 149458 GE Digiplex RS 422 iI Baud rate 4800 123456 Setting the communication DIP switches See Figure 1 for the location of the communication DIP switches The RS 485 default setting is half duplex see Figure 2 below For further information on the other options available please refer to the user manual Figure 2 Default setting of RS 485 communication switch half duplex 10 TruVision Mini PTZ 12X Camera Pocket Guide Setting the dome camera site ID Before turning on the dome camera you must setthe dome camera site ID Each dome camera connected to the same network must have a unique site ID Use the 10 bit DIP switch to setthe dome camera site s ID
7. nput terminal block See Figure 6 on page 15 TruVision Mini PTZ 12X Camera Pocket Guide Figure 6 Ground wire for power input elii 24 VAC SN 24 VAC Main menu overview The dome camera is programmed through the on screen OSD menus To access the OSD menus you must open the main menu The main menu which appears over three screens lets you set up the dome camera or change the default settings to suit your installation See Figure 7 on page 16 Note The OSD menu can be pre programmed to time out after certain number of minutes of inactivity All configuration changes made are automatically saved Please refer to the user manual for detailed information on programming the dome camera and on screen displays TruVision Mini PTZ 12X Camera 15 Pocket Guide Figure 7 Main menu screens MAIN PAGE 1 LANGUAGE ENGLISH gt DEFAULT ENTER y BACKLIGHT OFF gt FOCUS AUTO gt EXPOSURE CONTROL ENTER y WHITE BALANCE AUTO gt CAMERA SETUP ENTER x PAN TILT SETUP ENTER r MAIN PAGE 2 SITE ID AREATITLE OFF gt AREA TITLE NUM 014 PRESET ENTERL PRESET TOUR ENTER AUTOPAN ENTERL SHADOW TOUR ENTER AUTO RETURN ENTER MAIN PAGE 3 DAY NIGHT AUTO ALARM SETTING ENTER ALARM DETECT NONE WDR FUNCTION NONE PRIVACY MASK ENTER TIME DATE ENTER SCHEDULE ENTER EXIT OSD YES 16 TruVision Mini PTZ 12X Camera Pocket Guide Using a keypad to program menus Use control devic
8. result in serious injury Refer all servicing to qualified service personnel TruVision Mini PTZ 12X Camera 3 Pocket Guide Example of a system setup RS 485 Video 1 Main monitor 4 DVR Multiplxer Quad Switcher 2 Spot monitor 5 Camera 3 Control 6 Repeater keypad Cable requirements Table 1 lists the requirements for the cables that connect to the dome camera 4 TruVision Mini PTZ 12X Camera Pocket Guide Table 1 Recommended cable requirements Operation Cable requirement Max length Data RS STP shielded twisted pair cable 1219 m 485 4000 ft Cat 5 cable recommended If the total cable length exceeds 1219 m 4000 feet using a repeater to maintain the signal is recommended Video 75 ohm coaxial cable with BNC ends 486 m 1600 ft Alarm Cat 5 cable recommended 381m 1250 ft Power 24 VAC cable To determine the size of cable needed for individual applications please refer to the user manual TruVision Mini PTZ 12X Camera 5 Pocket Guide Removing the protective cover from the outdoor camera For detailed instructions please refer to the user manual 1 Unpack the camera 2 Detach the outdoor top mount bracket counterclockwise and detach it from the main camera housing 3 Remove the protective cover and PE sheet from the camera 6 TruVision Mini PTZ 12X Camera Pocket Guide 4 After smearing some lubricant on the surface of the bubble waterproof rubber
9. setting For more detailed information on setting the dome camera site DIP switches please refer to the user manual Figure 3 Example of setting DIP switches for the dome camera site ID 210 128 64 16 2 To set adome camera site ID 1 Locate the dome camera site ID DIP switch block E Figure 1 on page 9 2 Determine which DIP switches when turned on will add up to the site ID number for that dome camera See Figure 3 above for an example 3 Place the switches that correspond to those values in the On position 4 Carefully record the site ID of each dome camera installed TruVision Mini PTZ 12X Camera 11 Pocket Guide 22 pin connector description The 22 pin connector for I O interface cable connection is located on the back plate of the dome camera Please refer to the table below for the pin descriptions 1 21 Table 3 22 pin connector Pin Description Pin Description 1 Power In AC 24 1 12 Alarm Contact 1 2 Alarm Relay NC 13 Alarm Contact 2 3 Power In AC 24 2 14 Alarm Contact 3 4 Alarm Relay NO 15 Alarm Contact 4 5 Power Earth 16 Alarm Contact 5 Ground 6 Relay Com 17 Alarm Contact 6 Control T 18 Alarm Contact 7 8 Control R 19 Alarm Contact 8 9 Control T 20 Alarm Contact GND 10 Control R 21 Video GND Li ISOG 22 Video POS 12 TruVision Mini PTZ 12 Camera Pocket Guide Wiring the dome camera The TruVision Mini PTZ 12X Camera is shipped with a 24 VAC I O
10. tion When a menu has gt y scroll left and right to select a menu function and then press the set key to enter the submenu Iris Enters or selects a menu option IriS Iris Esc Exits a menu option There is no need to select the menu option Exitto quita menu 18 TruVision Mini PTZ 12X Camera Pocket Guide Figure 8 Joystick motion Scroll up Previous Next Scroll down Edit turn joystick clockwise TruVision Mini PTZ 12X Camera 19 Pocket Guide
Download Pdf Manuals
Related Search