Generac Gn - 410 Portable Generator User Manual
Contents
1. MEMORY BUTT Q FLASH tte LINE SPEAKS RPH SPEAKERPHONE BUTTON amp LED KA BUTTON STORE BUTTON Installation Modular Wall Jack A modular wall jack is required to install your FT365 CR or E N Installation of this telephone in locations with 4 prong jacks Sy or with hardwired outlets requires additional converters not included Contact your local telephone company or retailer concerning the proper converter Coil Cord Connection Insert the coil cord into the jack located on the bottom of the base Connect the other end into the jack located on the handset Ss IN Line Cord Connection To use both lines of a two line telephone two telephone numbers must be provided by your local telephone company If you have only one telephone number another line can be installed by your telephone company For One Two Line Jack Insert one plug of the 4 wire modular line cord included into the wall jack making sure it snaps firmly in place Insert the other plug of the 4 wire line cord into the telephone jack marked LINE 1 2 on back of base UNE1 2 LINE For Two Single Line Jacks For two single line jacks two separate line cords are needed for the connection Insert one plug of the 4 wire line cord included into the first telephone wall jack Insert the other plug of the 4 wire line cord into t2. 3 16 from the wall Insert one plug of long 4 wire line cord into the wall jack and insert the other plug into the telephone jack marked LINE1 2 making sure the plugs snap firmly in place You can weave the cord through the notches on the bottom of the base Position the wall mount slots on the bottom of the base over the two screws on the wall Push down to lock in plage BATTERIES Four 1 5 volt AAA alkaline batteries not included are required to work the telephone functions properly In normal use the batteries will last approximately six months Install the batteries into the compartment on the bottom of the telephone ILI 1 Openthe BATTERY COMPARTMENT COVER 2 Insert the batteries matching the plus and minus signs inthe COMPARTMENT 3 Replace the COVER Basic Operation PULSE TONE SWITCH SET THIS SWITCH on the side of base TO THE SERVICE PULSE or TONE SUPPLIED TO YOUR PHONE If you are not certain of which service you have set the switch to TONE Lift the HANDSET and press any number on the DIAL KEYPAD If the dial tone persists reset to PULSE RINGER VOLUME CONTROLS The RINGER VOLUME CONTROLS for both Line 1 and Line 2 on the right side of the base adjust the ringing volume of each individual line Set the switch to HIGH LOW or OFF HANDSET SPEAKERPHONE You can use either the HANDSET or SPEAKERPHONE mode during a conversation During a call one or the other can be used and
3. handling California residents need only provide proof of purchase You may also have other warranty rights which vary from state to state This warranty shall be invalid if the product is damaged as a result of defacement misuse abuse neglect accident destruction or alteration of the serial number improper electrical voltages or currents repair alteration or maintenance by any person or party other than our own service facility or an authorized service center or any use violative or instructions furnished by us This warranty is also rendered invalid if this product is removed from the country in which it was purchased if it is used in a country in which it is not registered for use and or if it is used in a country for which it was not designed Due to variations in telephone systems and communications laws this product may be illegal for use in some countries Southwestern Bell Freedom Phone Retail Sales assumes no responsibility for damages or penalties incurred resulting from the use of this product in a manner or location other than that for which it is intended This one year warranty is in lieu of all other expressed warranties obligations or liabilities ANY IMPLIED WARRANTIES OBLIGATIONS OR LIABILITIES INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE SHALL BE LIMITED IN DURATION TO THE ONE YEAR DURATION OF THIS WRITTEN LIMITED WARRANTY Some states do not allow li
4. release of the battery electrolyte may occur causing burns or irritation to eyes or skin 7 When replacing batteries all batteries should be replaced at the same time Mixing fresh and discharged batteries could increase internal cell pressure and rupture the discharged batteries 8 When inserting batteries into this product the proper polarity or direction must be observed Reverse insertion of batteries can cause charging and that may result in leakage or explosion 9 Remove the batteries from this product if the product will not be used for a long period of time several months or more since during this time the batteries could leak in the product 10 Discard dead batteries as soon as possible since dead batteries are more likely to leak in a product 11 Do not store this product or the batteries identified for use with this product in high temperature areas Batteries that are stored in a freezer or refrigerator for the purpose of extending shelf life should be protected from condensation during storage and defrosting Batteries should be stabilized at room temperature prior to use after cold storage a SAVE THESE INSTRUCTIONS Table of Contents Important Safety INStrUCtiONS 0 ee ee eee eee eee ee ee nee eens tenet teeaeneeeeeeaee Safety Instructions for Batteries Unpacking Telephone Installation Location of Controls Installation Line Cord Connection 2 Power Adapto iirst Sener
5. unstable cart stand or table The product may fall causing serious damage to the product 6 Slots or openings in the cabinet and the back and bottom are provided for ventilation to protect it from overheating These openings must not be blocked or covered The openings should never be blocked by placing the product on a bed or other similar surface This product should never be placed near or over a radiator or heat register 7 Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or short out parts which could result in the risk of fire or electric shock Never spill liquid of any kind on the product 8 To reduce the risk of electric shock do not disassemble this product Instead when service or repair work is required take it to a qualified technician but take it to a qualified serviceman when some service or repair work is required Opening or removing covers may expose you to dangerous voltages or other risks Incorrect reassembly can cause electric shock when the appliance is subsequently used 9 Unplug this product from the wall telephone jack and refer servicing to qualified service personnel under the following conditions If liquid has been spilled into the product If the product has been exposed to rain or water c If the product does not operate normally by following the operating instructions Adjust only those controls that are covered by the operating inst
6. which you wish to continue the conversation The other caller will be disconnected To disconnect both parties hang up the handset or press the SPEAKERPHONE BUTTON if you are already in the speakerphone mode _ 9 LINE 2 HOLD CONFERENCE Feature Operation con t HEADSET JACK You can connect a headset not included for hands free conversations 1 Insert the headset plug must be 5 32 inch 3 5mm type into the headset jack on the side of the base You may need to lift the rubber protective cover from the jack 2 Adjust the headset microphone to a comfortable position placing it near your mouth 3 Press the SPEAKERPHONE BUTTON to make or receive a call Adjust the volume to a desirable level by moving the speaker volume switch on the side of the base NOTE 1 If you are using a headset not included with a 2 5mm plug attach the headset adaptor included to the headset jack on the side of the base Then insert the headset plug into the adaptor 2 You can purchase a suitable headset through our help line at 1 800 366 0937 or our secure website at http www swbfreedomphone com A P LINE STATUS OPERATION STATUS LINE 1 BUTTON LINE 2 BUTTON LED LED ON HOOK OFF OFF LINE 1RINGING FLASH RAPIDLY OFF LINE 1 IN USE LIT SOLID OFF LINE 1 HOLD FLASH SLOWLY OFF LINE 2RINGING OFF FLASH RAPIDLY LINE 2INUSE JOFF LIT SOLID LINE 2 HOLD OFF FLASH SLOWLY CONF MODE ON ON LINES
7. 1 amp 2 FLASH SLOWLY FLASH SLOWLY HOLD 14 TROUBLE SHOOTING If the solution to your problem is not listed below call our toll free SERVICE NUMBER 1 800 366 0937 Monday Friday 8 30 a m 9 00 p m EST and Saturday 8 30 a m 12 30 p m EST You can also visit our website at http www swbfreedomphone com PROBLEM POSSIBLE CAUSE CORRECTION ACTION No dial tone mproper Installation Recheck all modular plug connections Press the corresponding key Line lor Line 2 Problem with the wiring Try another phone jack If your phone works on another jack you may have a problem with your wiring Contact your local phone company Cannot make outgoing calls Tone Pulse switch is not set correctly Check the Tone Pulse switch If positioned in tone mode switch to pulse as you may have pulse dialing service The phone does not ring Ringer Off Low High switch is notset Set the Ringer Off Low High switch to the correctly Low or High position 00 many telephones are installed on Contact your telephone company to he same line determine the maximum number of extensions for your calling area Memory dialing does not he memory storage procedure was not Carefully review the store sequence and work followed correctly reenter your programmed number he sound volume is too Another extension is off hook Hang up extension Ws Receiver volume control is too low Adju
8. 8 of the FCC rules On the bottom of the base of this equipment is a label that contains among other information the FCC Registration Number and Ringer Equivalence Number REN for this equipment You must upon request provide this information to your telephone company The REN is useful to determine the quantity of devices you may connect to your telephone line and still have all of those devices ring when your telephone number is called In most but not all areas the sum of the RENS of all devices connected to one line should not exceed five 5 0 To be certain of the number of devices you may connect to your line as determined by the REN you should contact your local telephone company to determine the maximum REN for your calling area If your telephone equipment causes harm to the telephone network the telephone company may discontinue your service temporarily If possible they will notify you in advance But if advance notice isn t practical you will be notified as soon as possible You will be informed of your right to file a complaint with the FCC Your telephone company may make changes in its facilities equipment operation or procedures that could affect the proper functioning of your equipment If they do you will be notified in advance to give you an opportunity to maintain uninterrupted telephone service If you experience trouble with this telephone equipment disconnect from the network until the problem has been corre
9. Freedom Phone toll free Customer Help Line for assistance Monday Friday 8 30 am 9 30 p m EST and Saturday 8 30 a m 12 30 p m EST You can also visit our website at http www swbfreedomphone com FOR IN WARRANTY SERVICE Package your complete unit including all line cords and other accessories and ship the unit postage prepaid and insured for your protection to SOUTHWESTERN BELL FREEDOM PHONE DEPT In Warranty 7475 N Glen Harbor Blvd Glendale AZ 85307 Be sure to include your return address proof of purchase a daytime phone number 9 50 for postage and handling and a brief explanation of your difficulties NOTE California residents need only provide proof of purchase and should call 1 800 366 0937 for shipping instructions FOROUT OF WARRANTYSERVICE you may call our toll free Help Line for the price of a replacement before returning your unit Please follow all instructions for In Warranty Service above to return your unit and mark the package DEPT Out of Warranty QUESTIONS STOP DON T TAKE ME BACK TO THE STORE LOOK FOR THE TOLL FREE HELP TELEPHONE NUMBER LISTEN AS THE EXPERTS TALK YOU THROUGH THE PROBLEM For immediate answers to your questions regarding operation missing parts or installation call the Southwestern Bell Freedom Phone Help Line 1 800 366 0937 http www swbfreedomphone com 16 FCC Wants You To Know This equipment complies with Part 6
10. IS AVAILABLE FROM YOUR TELEPHONE COMPANY AND YOU HAVE THIS SERVICE you will be alerted by a signal determined by your telephone company if there is another call NOTE Your conversation will be muted momentarily during this signal 1 When you hear the signal to access the new call without disconnecting the call you are on press the FLASH BUTTON ED oO 2 To return to your original conversation press the KS FLASH BUTTON again STORE MUTE This procedure can be repeated as frequently as you desire Refer to your Telephone Company s instructions for this service The FLASH BUTTON can also be used to access a new dial tone without hanging up or to access other custom telephone company services HOLD THE PARTY YOU ARE CONVERSING WITH CAN BE PUT ON HOLD 1 Whether you are using the HANDSET or SPEAKERPHONE press the HOLD BUTTON The LINE 1 LINE 2 BUTTON will flash slowly and the SPEAKERPHONE BUTTON LED will go off RETURN TO A CALL ON HOLD ised Ni So a Lift the HANDSET or press the SPEAKERPHONE BUTTON OOO The LINE 1 LINE 2 and SPEAKERPHONE buttons will be pele lit solid and this call is no longer on Hold Ile NOTE A call on Hold can be picked up by any single line telephone connected on the same line When the call is on Hold do NOT press the HOLD BUTTON a second time to release the hold There will be a brief pause after releasing the hold before you can hear the caller b If you ar
11. STOP DON T TAKE ME BACK TO THE STORE LOOK FOR THE TOLL FREE HELP TELEPHONE NUMBER LISTEN AS THE EXPERTS TALK YOU THROUGH THE PROBLEM For immediate answers to your questions regarding operation missing parts or installation call the Southwestern Bell Freedom Phone Retail Sales Help Line at 1 800 366 0937 Monday Friday 8 30 a m 9 00 p m EST Saturday 8 30 a m 12 30 p m EST http www swbfreedomphone com SOUTHWESTERN BELL FREEDOM PHONE 7475 N Glen Harbor Blvd Glendale AZ 85307 FT 365 IB 3631 Printed in China Southwestern Bell Freedom Phone 2 Line Telephone With Speakerphone D LINE1 LINE 2 HOLD CONFERENCE OOOO TOLL FREE HELP LINE 1 800 366 0937 FT365 OWNER S MANUAL IMPORTANT SAFETY INSTRUCTIONS Before using your telephone equipment basic safety precautions should always be followed to reduce the risk of fire electric shock and injury to persons including the following 1 Read and understand all instructions 2 Follow all warnings and instructions marked on the product 3 Unplug this product from the wall telephone jack before cleaning Do not use liquid cleaners or aerosol cleaners Use a damp cloth for cleaning 4 Do not use this product near water for example near a bath tub wash bowl kitchen sink laundry tub wet basement or swimming pool 5 Do not place this product on an
12. cted or until you are sure that the equipment is not malfunctioning This equipment may not be used on coin service provided by the telephone company Connection to party lines is subject to state tariffs This equipment is hearing aid compatible Warning Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment Cleaning Use a damp cloth for cleaning Never use abrasives or solvents in cleaning Never spray cleaners directly on the telephone Limited Warranty The obligation of Southwestern Bell Freedom Phone Retail Sales under this warranty shall be limited to repair or replacement at our option during the warranty period of any part which proves defective in material or workmanship under normal installation use and service provided the product is returned to Southwestern Bell Freedom Phone Retail Sales or to one of our authorized Service Centers TRANSPORTATION CHARGES PREPAID California residents should call 1 800 366 0937 for shipping instructions Products returned to us or to an Authorized Service Center must be accompanied by a copy of the purchase receipt In the absence of such purchase receipt the warranty period shall be one 1 year from the date of manufacture To obtain service under this warranty return the defective product to the service center nearest you together with your sales slip and 9 50 for postage and
13. e not already connected to the caller press the LINE BUTTON with the IN USE LED flashing 12 Feature Operation con t CONFERENCE ESTABLISH A CALL The CONFERENCE BUTTON establishes a three way conversation with you and the callers on Lines 1 and 2 a Make a call to one outside party The activated LINE 1 LINE 2 BUTTON will be lit solid b Press the HOLD BUTTON The activated LINE 1 LINE 2 BUTTON will flash rapidly c Press the other LINE BUTTON You will hear a dial tone and the second activated LINE 1 LINE 2 BUTTON will be lit solid d Make a call to the second outside party e Press the CONFERENCE BUTTON and the LINE 1 and LINE 2 BUTTONS will both be lit solid YOU can now speak with both callers at the same time NOTE In the conference mode there may be a slight decrease in volume for the 2 callers WHILE IN CONFERENCE To put one caller on hold press the HOLD BUTTON and the LINE 1 and LINE 2 BUTTONS will alternately flash If you wish to continue speaking with the caller on Line 1 press the LINE 1 BUTTON and that button will be lit solid If you wish to speak with the caller on Line 2 press the LINE 2 BUTTON and that button will be lit solid To return to the conference call and speak with both callers press the CONFERENCE BUTTON The LINE 1 LINE 2 BUTTONS will both be lit solid AT THEEND OF A CONFERENCE CALL To speak to one party and disconnect the other press the LINE BUTTON for the caller with
14. eae a aE EEEIEE E a Batteries c tecetetetesecececececeeesecensceaseaeasasracecectecccseccetesesiesececensteiatets a etateeanierscecdaiat coat Basic Operation Pulse Tone Switch Ringer Volume Controls Handset Speakerphone Speaker Volume Control 3 Handset Receiver Volume Control 0 0 cee eee ee eeee ce eeeeneeeseeeeneseeeeeeenee Place A Gall s inea ee ecole eons ae e aa a ieii e aia Answer A Call ae Obtain A Dial Tone Immediately After a Call Is Ended 0 ee Feature Operation snye a or eaat a ar a aa cts ESEE aaa E E aa 10 Memory Dialing Mute nosenie Lighted keypad Call Waiting Flash CONO NCE RAR RE R cc csaen 13 Establish A Call While In Conference At The End Of A Conference Call Headset feo EEE EE EE EE EEES N Line Status Operation i TROUDIO lt SHOOtING sx c ct ceaccstecnccccceccatecisssssenennbnssuenpatecscninesascadsencusapuevasoeinnpuratedeccedececses RE EURE SAE AE E EEE AT ahi alsa tae naneandsnies FCC Wants You To Know 3 Etetea lalo svete ses E E E E E E E iat ete Limited Warranty ienn nereyi ietis in E AOKNAA Congratulations You have purchased a 2 LINE SPEAKERPHONE TELEPHONE which has been manufactured to the highest standards set by SOUTHWESTERN BELL FREEDOM PHONE Please read this OWNER S MANUAL thoroughly to become acquainted with the telephone s many features UNPACKING Check the contents of the carton to be sure that you have gt Teleph
15. he BUTTON and all further dialing functions will be in the TONE mode until you end the call N ov MEMORY STORE A A 4 At the end of the call return the HANDSET to the CRADLE or if you used the SPEAKERPHONE press the SPEAKERPHONE BUTTON again The lit buttons and keypad will go off ANSWER A CALL When a call is received the LINE 1 or LINE 2 button will flash to indicate which line is ringing 1 Lift the HANDSET or press the SPEAKERPHONE BUTTON to answer the call The activated LINE1 LINE2 or the SPEAKERPHONE button will be lit solid 2 When the conversation is completed hang up the telephone or press the lit LINE 1 LINE 2 button The lit buttons and keypad will go off NOTE Your FT365 features two distinct rings one for each line OBTAIN A DIAL TONE IMMEDIATELY AFTER A CALL IS ENDED At the end of a call if you wish to start another call without hanging up the handset press the FLASH BUTTON You will hear a dial tone Feature Operation MEMORY DIALING Your FT365 is equipped with 16 memories six priority speed dial ten keypad for programming your most frequently dialed telephone numbers You can store up to 32 digits in each of the speed dial keys 1 6 near the top of the phone or in each of the translucent dialing keys 0 9 Numbers must be stored with the HANDSET lifted They will be stored as dialed in the PULSE or TONE mode To enter numbers on the MEMORY INDEX CARD pry out the plastic cove
16. he telephone jack back of unit marked LINE1 2 Insert one plug of the second line cord not included into the second telephone wall jack Insert the other plug of the second line cord into the telephone jack marked LINE 2 6 Power Adaptor You can connect an optional Class 2 Power Adaptor not included which is listed to UL1310 for increased speakerphone performance Connect the power adaptor into the DC Adaptor Jack 9VDC 100mA on the back of the base and into the wall power outlet You can purchase a Power Adaptor through our help line at 1 800 366 0937 our secure website at http www swbfreedomphone com or your local retailer Wall Mounting on a Wall Plate Your FT365 telephone is also designed to be mounted on a wall which uses the One Jack option Insert one plug of the short line cord into the wall jack and insert the other plug into the telephone jack marked LINE1 2 making sure the plugs snap firmly in place You can weave the cord through the notches on the bottom of the base Position the wall mount slots on the bottom of the base over the two studs on the wall plate Push down to lock in place Wall Mounting on Two Screws If you do not have a wall phone plate and want to install your FT365 onto the wall fasten two screws not included into the wall using anchors for secure assembly Locate the screws 3 1 4 apart vertically They should extend
17. key 0 9 on the 2 amp keypad 5 Your programmed telephone number will automatically be dialed CHAIN COMBINATION DIALING NUMBERS IN TWO OR MORE MEMORY LOCATIONS CAN BE DIALED IN SEQUENCE AND COMBINED MANUAL AND MEMORY DIALING IS POSSIBLE IN EITHER ORDER This is especially convenient when using a long distance custom service that requires more than 32 digits REDIAL THE LAST NUMBER YOU DIALED MANUALLY OR BY SPEED A DIALING CAN BE REDIALED AUTOMATICALLY The maximum O Gee number of digits that can be redialed is 32 1 Lift the HANDSET or use the SPEAKERPHONE 2 Refer to the PLACE A CALL section to choose the desired LINE1 LINE2 3 When you have a dial tone press the REDIAL BUTTON The number will be automatically dialed MUTE Prevent sound from your room from being heard by another party on the phone Press and hold the MUTE BUTTON for as long as you want this feature activated Once you release the MUTE BUTTON the outside caller can hear you again 11 Feature Operation con t LIGHTED KEYPAD A lighted keypad is provided for better visibility NOTE In both the SPEAKERPHONE and HANDSET MODES the keypad will light while a phone number is dialed While in the SPEAKERPHONE MODE the keypad will slowly turn off within 5 10 seconds after a phone number is dialed In the HANDSET MODE the keypad will remain lit for as long as the HANDSET is off the CRADLE CALL WAITING FLASH IF CALL WAITING SERVICE
18. mitations on how long an implied warranty lasts so the above limitations may not apply to you IN NO EVENT SHALL WE BE LIABLE FOR ANY SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY EXPRESSED OR IMPLIED WHATSOEVER Some states do not allow the exclusion or limitation of special incidental or consequential damages so the above limitation or exclusion may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state 18
19. one Base p Handset Coil Cord and Telephone Line Cord gt 3 5mm to 2 5mm Headset Adaptor If anything is missing or damaged contact the place of purchase Keep the packaging to transport the telephone Telephone Installation CAUTION Never install telephone wiring during a lightning storm Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations Never touch uninsulated telephone wires or terminals unless the incoming telephone line has been disconnected at the network interface Use caution when installing or modifying telephone lines Always disconnect all telephone lines from the wall outlets before servicing or disassembling this equipment or replacing batteries Read operating manual before using as ow N Location of Controls Base LINE2JACK LINE 1 2 JACK DC POWER JACK LoKswich N O MEMORY INDEX CARD AND COVER HANDSET GUIDE MEMORY SPEED gt DIAL BUTTONS LINE 2 BUTTON amp INUSELED LINE 1 BUTTON amp IN USE LED LINE1 LINE2 HOLD CONFERENCE PERETET aa as OOO CONFERENCE BUTTON RTE HOLD BUTTON eooo sees eens E ooo0oo0oo00000 0890000 0 0 ae PULSE TONE eoo0oo0o00o0o0o0 28eoscecs KEY PAD __ eececee LINE 2 RINGER et e LINE 1 RINGER Donj sz O STORE ME A MUTE BUTTON CRADLE SPEAKER VOLUME CONTROL FLASH BUTTON
20. r take out the card make your entries then reinsert the CARD and COVER To Program A Number Into Memory Lift the HANDSET You will hear a dial tone 1 2 Press the STORE BUTTON N ii MUTE 3 Using the KEYPAD enter the telephone number you wish to store 32 digit maximum AS 4 Press the STORE BUTTON again G O 5 Press one of the SPEED DIAL KEYS 1 6 near the top of the phone or the translucent dialing keys 0 9 The telephone number will be stored in this location 6 To continue programming a telephone number into another memory location repeat steps 2 5 To end programming numbers return the HANDSET to the CRADLE 7 The telephone number can be dialed on either LINE 1 or LINE 2 10 Feature Operation con t TO ERASE A STORED NUMBER To erase a stored number simply store a new number in the same location The new number will replace the previous one TO DIAL PRIORITY NUMBERS K 1 Lift the HANDSET or use the SPEAKERPHONE z 2 Refer to the PLACE A CALL section to choose the desired A xz zzo LINE1 LINE2 ae 3 Press the desired SPEED DIAL KEY 1 6 near the top of the unit 4 Your programmed telephone number will automatically be dialed TO DIAL KEYPAD MEMORY NUMBERS 1 Lift the HANDSET or use the SPEAKERPHONE ae 2 Refer to the PLACE A CALL section to choose the desired LINE 1 LINE 2 Jee 3 Press the MEMORY BUTTON ag 5 5 4 Press the desired translucent dialing
21. ructions because improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to normal operation d If the product has been dropped or the cabinet has been damaged e Ifthe product exhibits a distinct change in performance 10 Avoid using a telephone other than a cordless type during an electrical storm There may be a remote risk of electric shock from lightning 11 Do not use the telephone to report a gas leak in the vicinity of the leak 1 gw SAFETY INSTRUCTIONS FOR BATTERIES To reduce the risk of fire or injury to persons read and follow these instructions 1 Use only the size and type of batteries mentioned in the Owner s Manual 2 Do not dispose of the batteries in a fire The cells may explode Check with local codes for possible special disposal instructions 3 Do not open or mutilate the batteries Released electrolyte is corrosive and may cause damage to the eyes or skin It may be toxic if swallowed 4 Exercise care in handling batteries in order not to short the battery with conducting materials such as rings bracelets and keys The battery or conductor may overheat and cause burns Do not attempt to recharge the batteries identified for use with this product The batteries may leak corrosive electrolyte or explode 6 Do not attempt to rejuvenate the batteries identified for use with this product by heating them Sudden
22. st receive volume control level Cannot hear any sound or e headset may still be connected to Unplug the headset from the FT365 base ial tone through the e unit and make the call through the handset or andset or speakerphone speakerphone he hold function does not e batteries need to be replaced or nstall four fresh AAA batteries before initial work ave not been installed use he LINE 1 or LINE 2 e batteries have not been installed or Install four fresh AAA batteries before initial BUTTONS do notlight or need to be replaced use are too weak he LINE 2 BUTTON is Only a single line jack is Connected You must have 2 separate telephone constantly lit solid e telephone may not be connected to numbers to use both the Line 1 and Line 2 the correct jack on the back of the unctions Refer to page 6 for installation base instructions Hear both a dial tone and e conference mode may be activated Press one of the LINE BUTTONS to release e outside caller he conference mode HEARING AID COMPATIBILITY Your FT365 is compatible with inductively coupled hearing aids 15 Repair Service According to FCC regulations this equipment which has been certified and registered by the FCC may only be repaired by authorized persons If repairs or adjustments are made by an unauthorized person the FCC certification may be voided Should your encounter any problems please call the Southwestern Bell
23. they can be interchanged at any time other than during dialing The HANDSET is activated when the HANDSET is lifted off its cradle The SPEAKERPHONE is activated when you press the SPEAKERPHONE BUTTON and the SPEAKERPHONE BUTTON will then light At the end of the call press the SPEAKERPHONE BUTTON again and the SPEAKERPHONE BUTTON will turn off To switch from the SPEAKERPHONE to the HANDSET lift the HANDSET To switch from the HANDSET to the SPEAKERPHONE without losing the call press the SPEAKERPHONE BUTTON first before you place the HANDSET in the cradle and the SPEAKERPHONE BUTTON will light SPEAKER VOLUME CONTROL When using the Speakerphone adjust the speakerphone loudness by moving the SPEAKER VOLUME CONTROL on the side of the base from LOW to HIGH HANDSET RECEIVER VOLUME CONTROL When speaking through the handset adjust the receiver loudness of the handset by moving the RECEIVER VOLUME CONTROL on the side of the handset to NORM or HIGH Basic Operation PLACE A CALL 1 Lift the HANDSET or press the SPEAKERPHONE BUTTON You will hear a dial tone and the activated LINE 1 LINE 2 or the SPEAKERPHONE button will light 2 Press LINE 1 or LINE 2 BUTTON to switch to the other line The newly activated LINE 1 LINE 2 BUTTON will light 3 When you hear a dial tone dial the number Mixed Dialing If you have Pulse Service you can temporarily switch to Tone dialing if required for various custom services Press t
Download Pdf Manuals
Related Search