Garmin 190-01155-02 Marine GPS System User Manual
Contents
1. For future reference write the serial number assigned to your GPSMAP 700 series chartplotter in the space provided The serial number is located on a sticker on the back of the device Chartplotter serial number To install the GPSMAP 700 series chartplotter you must 1 Mount the GPSMAP 700 series chartplotter 2 Connect the chartplotter to power page 5 3 Ensure that the chartplotter software is up to date page 7 The following additional installation options are not necessary in order to use the GPSMAP 700 series chartplotter They have been included for your convenience Connecting the chartplotter to a NMEA 2000 network page 6 e Connecting the chartplotter to a GA 30 remote GPS antenna page 6 Connecting the chartplotter to a Garmin marine radar page 6 Connecting the chartplotter to other NMEA 0183 compatible devices such as a VHF radio with DSC page 5 e Connecting the chartplotter to a sonar transducer s models only page 6 Mounting the Chartplotter You can mount the GPSMAP 700 series chartplotters using one of two methods You can use the included bracket and hardware to bail mount the chartplotter or you can use the included template and hardware to flush mount the chartplotter Mount the GPSMAP 700 series chartplotter in a location that provides a clear glare free view of the display and easy operation of the power key and the touch screen February 2010 Part Number 190 01155 02 Rev B Prin2. A Position Report 129285 Navigation Route WP information 129039 AIS Class B Position Report 129539 GNSS DOPs 129040 AIS Class B Extended Position Report 129540 GNSS Sats in View 129794 AIS Class A Static and Voyage Related Data 130306 Wind Data 129798 AIS SAR Aircraft position report 129799 Radio Frequency Mode Power 129802 AIS Safety Related Broadcast Message 129808 DSC Call Information 130306 Wind Data GPSMAP 700 series chartplotters are NMEA 2000 130576 Small Craft Status certified 130310 Environmental Parameters 130311 Environmental Parameters Obsolete 130312 Temperature 130313 Humidity 130314 Actual Pressure NMEA 0183 Information NMEA 0183 Version 3 01 Sentences Receive Transmit DPT Depth GPAPB APB Heading Track Controller Autopilot Sentence B DBT Depth Below Transducer GPBOD BOD Bearing Origin to Destination MTW Water Temperature GPBWC BWC Bearing amp Distance to Waypoint VHW Water Speed and Heading GPGGA GGA Global Positioning System Fix Data WPL Waypoint Location GPGLL GLL Geographic Position Latitude Longitude VDM AIS VHF Data Link Message GPGSA GSA GNSS DOP and Active Satellites DSC Digital Selective Calling Information GPGSV GSV GNSS Satellites in View DSE Expanded Digital Selective Calling GPRMB RMB Recommended Minimum Navigation Information HDG Heading Deviation amp Variation GPRMC RMC Recommended Minimum Specific GNSS Data HDM Heading Magnetic GPRTE RTE Routes MWD Wind Direction amp Speed GP
3. e Make sure the surface on which you mount the chartplotter has adequate open space behind it to fit the chartplotter and the connected cables and make sure to leave approximately 2 in 13 mm of space on the right side of the chartplotter to access the SD card door and sun cover To avoid interference mount a GPSMAP 700 series chartplotter at least 32 in 813 mm from a magnetic compass The flush mount template has adhesive on the back Remove the protective liner and apply the template to the location at which you want to mount the chartplotter 3 Using a s in 9 5 mm drill bit drill a pilot hole inside the corner of the template to begin cutting the mounting surface 4 Using the jigsaw cut the mounting surface along the inside of the solid line indicated on the flush mount template Use a file and sandpaper 9 to refine the size of the hole If the top and bottom mounting covers are attached to the front of the chartplotter remove them by unsnapping the covers from the sides Place the chartplotter in the hole and make sure that the mounting holes on the chartplotter line up with the pilot holes on the flush mount template after cutting sanding and filing the hole If they do not line up mark the locations where the pilot holes need to be Using the center punch indent the center of each of the mounting hole locations Using a t s in 3 mm drill bit drill the pilot holes NOTE If you are mounting th
4. the cable connector is at the mounting location of the chartplotter AA 2 Separate the two halves of the locking ring 3 Align the two halves of the locking ring over the cable and snap them together 4 Insert the O ring into the end of the connector Installing the Locking Ring Wire Color Wire Function Red Power 10 32 Vdc ON Ground Black power and NMEA 0183 Blue NMEA 0183 port 1 Tx out NMEA 0183 port 1 Rx in To the GPSMAP 700 Brown p n series chartplotter Gray NMEA 0183 port 2 Tx out E l lt Violet NMEA 0183 port 2 Rx in Green Spare White Spare Orange Accessory on Yellow Alarm low To transducer if applicable GPSMAP 700 Series Power Data Cable Notes e Use an AGC 3AG 3 Amp replacement fuse e If itis necessary to extend the power and ground wires use 16 AWG wire You can wire the cable directly to the battery or if your boat has an electrical system you might be able to wire the cable to an unused holder on the fuse block If you use the boat fuse block remove the in line fuse holder on the power wire of the cable Do not cut the transducer cable because this voids your warranty NOTICE The maximum input voltage is 32 Vdc Do not exceed this voltage because this can damage the chartplotter and void the warranty NOTE If you are not connecting the chartplotte
5. A GARMIN GPSMAP 700 Series Installation Instructions See the mportant Safety and Product Information guide in the product box for product warnings and other important information Always wear safety goggles ear protection and a dust mask when drilling cutting or sanding NOTICE When drilling or cutting always check what is on the opposite side of the surface to avoid damaging your boat The GPSMAP 700 series chartplotter must be properly installed according to the following instructions You need the appropriate fasteners tools and mounts listed in each section These items are available at most marine dealers Contact Garmin Product Support if you have any questions while installing your GPSMAP 700 series chartplotter In the USA go to www garmin com support or contact Garmin USA by phone at 913 397 8200 or 800 800 1020 In the UK contact Garmin Europe Ltd by phone at 0808 2380000 In Europe go to www garmin com support and click Contact Support for in country support information or contact Garmin Europe Ltd by phone at 44 0 870 8501241 Before installing your GPSMAP 700 series chartplotter confirm that the package contains the items listed on the box If any parts are missing contact your Garmin dealer immediately Product Registration Help us better support you by completing our online registration today Go to http my garmin com Keep the original sales receipt or a photocopy in a safe place
6. Instructions Appendix Specifications Physical Specifications Specification Measurement Size W x H x D 8 2 32 x 5 19 32 x 3 1 s in 226 x 142 x 80 mm Weight 2 48 Ib 1 125 kg Display W x H 6 x 3 19 32 in 152 x 91 mm Case Fully Gasketed high impact plastic and aluminum alloy waterproof to IEC 60529 IPX 7 Temp Range From 5 F to 131 F from 15 C to 55 C Compass Safe 32 in 813 mm Distance GPS Performance NMEA 2000 Load Equivalency Number LEN 2 Specification Parameter Measurement Receiver High sensitivity 12 parallel channel WAAS capable receiver Acquisition Warm Approximately 1 sec The device is at or near the last location at which you recently acquired satellites Time Cold Approximately 38 sec The device has moved more than about 500 mi 800 km since it was turned off Reacquisition lt 1 sec Update Rate 1 sec continuous Accuracy GPS lt 33 ft 10 m 95 typical DGPS 10 16 ft 3 5 m 95 typical WAAS EGNOS accuracy Velocity 0 05 m sec steady state Power Specification Measurement Source 10 32 Vdc Usage 8 56 W max at 13 8 Vdc Fuse 3A RMS 3 200 W peak to peak NMEA 2000 Draw 100 mA maximum Sonar Power 1 kW Transducer 1 000 W RMS 8 000 W peak to peak Dual Frequency 500 W RMS 4 000 W peak to peak Dual Beam 400 W Frequency 50 200 kHz dual f
7. VTG VTG Course Over Ground and Ground Speed MDA Meteorological Composite GPWPL WPL Waypoint Location MWV Wind Speed and Angle GPXTE XTE Cross Track Error VDM AIS VHF Data Link Message PGRME E Estimated error PGRMM M Map datum PGRMZ Z Altitude SDDBT DBT Depth Below Transducer SDDPT DPT Depth SDMTW MTW Water Temperature SDVHW VHW Water Speed and Heading You can purchase complete information about National Marine Electronics Association NMEA format and sentences from NMEA Seven Riggs Avenue Severna Park MD 21146 USA www nmea org GPSMAP 700 Series Installation Instructions Garmin the Garmin logo GPSMAP and AutoLocate are trademarks of Garmin Ltd or its subsidiaries registered in the USA and other countries GMR is a trademark of Garmin Ltd or its subsidiaries These trademarks may not be used without the express permission of Garmin NMEA 2000 and the NMEA 2000 logo are registered trademarks of the National Marine Electronics Association For the latest free software updates excluding map data throughout the life of your Garmin products visit the Garmin Web site at www garmin com A GARMIN 2010 Garmin Ltd or its subsidiaries Garmin International Inc 1200 East 151 Street Olathe Kansas 66062 USA Garmin Europe Ltd Liberty House Hounsdown Business Park Southampton Hampshire S040 9LR UK Garmin Corporation No 68 Jangshu 2 Road Sijhih Taipei County Taiwan ww
8. ation bracket diagram for the clip assignments 10 Place the bail mount bracket over the cable organization bracket and route the cables through the back of the bail mount bracket 11 Secure the bail mount to the surface using the four included 35 mm M 4 2 x 1 4 screws 12 Follow the steps on page 3 to install the GPSMAP 700 series chartplotter on the bail w Bail mount bracket amp O o 1 GA 30 GPS antenna cable clip 2 Power data cable clip mount bracket Test the slack length of the cables routed through the bracket Garmin Marine Radar cable clip 13 Make cable slack length adjustments if necessary Apply marine sealant optional NMEA 2000 cable clip Cable Organization Bracket Clip Identification 2 GPSMAP 700 Series Installation Instructions To install the bail mount bracket without the cables routed through the bracket f Using the included bail mount bracket template determine the best place to install the bracket Be sure to leave adequate clearance behind the chartplotter for the wiring NOTE To avoid interference mount the GPSMAP 700 series chartplotter at least 32 in 813 mm from a magnetic compass The bail mount bracket template has adhesive on the back Remove the protective liner and apply the template to the location at which you want to install the bail mount bracket Use a t s in 3 mm drill bit to drill the four outer pilot holes marke
9. d on the template Do not drill the two pilot holes marked on the cable organization bracket NOTE If you are mounting the chartplotter in fiberglass it is recommended to use a countersink bit to drill a clearance counter bore through only the top gel coat layer This will help to avoid any cracking in the gel coat layer when the screws are tightened 4 Remove the bail mount bracket template from the mounting surface 5 Secure the bail mount to the surface using the four included 35 mm M 4 2 x 1 4 screws NOTE Stainless steel screws may bind when screwed into fiberglass and overtightened Garmin recommends applying an anti galling stainless anti seize lubricant to the screw before using To install the GPSMAP 700 series chartplotter on the bail mount bracket 1 Loosely attach the mounting knobs to the GPSMAP 700 series chartplotter 2 Slide the chartplotter onto the bail mount and tighten the mounting knobs Flush Mounting the Chartplotter Hardware included Tools required not included Flush mount template e Jigsaw Four 35 mm M 4 2 x 1 4 screws Drill and drill bits s in 9 5 mm and s in 3 mm e Number 2 Phillips screwdriver Center punch and hammer File and sandpaper To flush mount a GPSMAP 700 series chartplotter 1 The flush mount template is included in the product box Trim the template and ensure it will fit in the location where you want to flush mount the chartplotter NOTES
10. e chartplotter in fiberglass it is recommended to use a countersink bit to drill a clearance counter bore through only the top gel coat layer This will help to avoid any cracking in the gel coat layer when the screws are tightened Place the chartplotter into the cutout 10 Securely tighten the four included 35 mm M 4 2 x 1 4 mounting screws through the chartplotter into the pilot holes NOTE Stainless steel screws may bind when screwed into fiberglass and overtightened Garmin recommends applying an anti galling stainless anti seize lubricant to the screw before using 11 Install the top and bottom mounting covers by snapping them into place GPSMAP 700 Series Installation Instructions Installing the Power Data Cable The chartplotter comes with a power data cable that connects the chartplotter to power and to optional NMEA 0183 devices If applicable the power data cable also connects the chartplotter to a sonar transducer The power data cable does not connect the chartplotter to a NMEA 2000 network For instructions on connecting the chartplotter to a NMEA 2000 network see page 6 To help make the cable routing process easier the locking ring is packaged separately from the cable If you install the power data cable through the bail mount do not install the locking ring until after all the cables are routed j Installing a locking ring on the cable 1 Route the cable away from sources of electronic interference so that
11. er is compatible with a Garmin marine radar but it is not compatible with the Garmin marine network Do not connect other Garmin marine network devices to the radar port on the GPSMAP 700 series chartplotter 3 Update the chartplotter software page 7 Connecting the Chartplotter to a GA 30 Remote GPS Antenna Optional The GPSMAP 700 series chartplotter has an internal GPS receiver but some installations such as a flush mount installation may not allow a view of the sky that the device needs to calculate your GPS position You can install a GA 30 remote GPS antenna not included in an appropriate location and connect it to the chartplotter to provide GPS information To connect the chartplotter to a GA 30 antenna 1 Install the GA 30 antenna according to the instructions provided with the antenna 2 Route the GA 30 cable to the chartplotter and connect it to the external GPS antenna connector Connecting the Chartplotter to a Transducer If you have a sonar cable GPSMAP 700 series chartplotter indicated by an s in the product name you can connect a Garmin transducer to use sonar specific features To connect the chartplotter to a transducer 1 Install the transducer according to the instructions provided with the transducer 2 Route the transducer cable to the chartplotter and connect it to the power data cable 6 GPSMAP 700 Series Installation Instructions Identifying the Rear Panel Connectors After the power data cab
12. ix pilot holes marked on the bail mount template NOTE If you are mounting the chartplotter in fiberglass it is recommended to use a countersink bit to drill a clearance counter bore through only the top gel coat layer This will help to avoid any cracking in the gel coat layer when the screws are tightened Remove the bail mount bracket template from the mounting surface Route the cables pertinent to your installation through the hole you drilled in step 3 from under the mounting surface If you plan to use all four cables route them in the following order to ensure that they will all fit correctly e Radar cable e Power data wiring cable e GA30 GPS antenna cable Bail Mounting the GPSMAP 700 Series Chartplotter e NMEA 2000 cable NOTE Do not install the locking ring page 4 on the power data or radar cable until after you route it through the mounting surface 7 Place the cable organization bracket around the cables and into the 1 4 in 32 mm hole you drilled in step 3 8 Use the two included 20 mm M 3 5 x 1 3 screws to secure the cable organization bracket to the mounting surface NOTE Stainless steel screws may bind when screwed into fiberglass and overtightened Garmin recommends applying an anti galling stainless anti seize lubricant to the screw before using 9 Extend 6 7 in 152 178 mm of cable slack through the cable organization bracket and secure each cable to the correct clips Refer to the cable organiz
13. le is wired to the boat and after any optional Garmin radar NMEA 0183 NMEA 2000 or external GPS devices are installed connect the cables to the GPSMAP 700 series chartplotter NOTE You must install the locking rings before connecting the power data cable or a Garmin radar cable to the chartplotter page 4 To connect a cable to the back of a GPSMAP 700 series chartplotter 1 Carefully press the cable into the correct port on the back of the chartplotter until it is firmly seated Do not force the cable because this may damage the pins 2 After the cable is seated turn the locking ring clockwise until it is tight Be careful not to overtighten the locking ring CLU LJ k GPSMAP 700 Series Connectors 1 NMEA 2000 connector 2 Radar port Power data connector O External GPS antenna connector Updating the Chartplotter Software The GPSMAP 700 series chartplotter may contain a software update SD card If so follow the instructions provided with the card Ifa software update SD card is not included visit www garmin com to make sure your chartplotter software is up to date To identify the version of software on your chartplotter select or touch Configure gt System gt System Information GPSMAP 700 Series Installation
14. lotter NMEA 0183 compatible device To connect the power data cable to a NMEA 0183 device 1 For Garmin devices the ground black wires serve as NMEA 0183 ground and must be attached together or on the same terminal as the NMEA 0183 ground on your NMEA 0183 device Refer to the wiring diagram of your NMEA 0183 device for wire identification 2 Connect the blue NMEA 0183 port 1 out wire from the GPSMAP 700 power data cable to the NMEA 0183 in or Rx A wire from the NMEA 0183 device and the brown NMEA 0183 port 1 in wire to the NMEA out or Tx A wire from the NMEA 0183 device 3 Repeat step 2 using the gray NMEA 0183 port 2 out and violet NMEA 0183 port 2 in wires for an additional NMEA 0183 device 4 Set the serial port or ports on the chartplotter to use NMEA 0183 data standard or high speed See the GPSMAP 700 Series Owner s Manual for more information Connecting the Power Data Cable to a Lamp or to a Horn Optional The GPSMAP 700 series chartplotter can be used with a lamp a horn or both to sound or flash an alert when the chartplotter displays a message The alarm does not need to be wired for the chartplotter to function The alarm circuit switches to a low voltage state when the alarm sounds The maximum current is 100 mA and a relay is needed to limit the current from the chartplotter to 100 mA To manually toggle visual and audible alerts install single pole si
15. ngle throw switches Battery 7 10 35 Vdc GPSmap 740s GPSMAP 700 series chartplotter 100 ma max coil current Wiring to a Lamp a Horn or Both GPSMAP 700 Series Installation Instructions an Connecting the Chartplotter to a NMEA 2000 Network Optional You can connect the GPSMAP 700 series chartplotter to your existing NMEA 2000 network You will need the appropriate NMEA 2000 cables and connectors either to connect the chartplotter to your existing NMEA 2000 network or to build a NMEA 2000 network if you do not have one installed on your boat Contact your local Garmin dealer If you are unfamiliar with NMEA 2000 read the NMEA 2000 Network Fundamentals chapter of the Technical Reference for Garmin NMEA 2000 Products The document is located on the included CD and on the NMEA 2000 section of the Garmin Web site at http www garmin com garmin cms us onthewater nmea2000 Connecting the Chartplotter to a Garmin Marine Radar Optional You can connect the GPSMAP 700 series chartplotter to a Garmin marine radar such as a GMR 18 HD not included To connect the chartplotter to a Garmin marine radar 1 Install the radar according to the installation instructions provided with the radar 2 Route the Garmin marine network cable to the chartplotter and connect it to the radar port NOTE The GPSMAP 700 series chartplott
16. r to NMEA 0183 devices use only the red and black wires The other wires do not have to be connected for normal operation of the chartplotter For information on connecting to a NMEA 0183 compatible device see page 5 4 GPSMAP 700 Series Installation Instructions Connecting the Power Data Cable to Power 1 Use a test light or a voltmeter to determine the polarity of the voltage source 3 A fuse 0 10 32 Vdc boat supply 2 Connect the red or positive wire to the positive voltage terminal If you use the Boat ground fuse block on the boat route the positive connection through the fuse as shown on the aa gt diagram i i l 3 Connect the black or ground wire to the negative voltage terminal 4 Install or check the 3 A fuse in the in line fuse holder or on the fuse block of the boat ae IB Connecting the Power Data cable to a NMEA 0183 Device Optional You can connect the GPSMAP 700 series chartplotter to other NMEA 0183 compatible equipment such as a DSC or AIS device Refer to the wiring diagram for connecting the chartplotter to NMEA 0183 compatible devices g da To device Fuse Block Example m GPSmap 740s Battery Wire color 10 32 Vdc Wire function Fuse 3A_ Red powe Black ground Power ground Blue out NMEA Ry A N Brown in NMEA Tx A Wiring a GPSMAP 700 Series Chartplotter to a Standard NMEA 0183 Device GPSMAP 700 series chartp
17. requency and 1 kW 80 200 kHz dual beam Depth 2 500 ft 762 m 1 kW 1 500 ft 457 m dual frequency 900 ft 274 m dual beam Depth capacity is dependent on water salinity bottom type and other water conditions NMEA 2000 PGN Information Receive Transmit 059392 ISO Acknowledgment 059392 ISO Acknowledgment 059904 ISO Request 059904 ISO Request 060928 ISO Address Claim 060928 ISO Address Claim 126208 NMEA Command Request Acknowledge Group Function 126208 NMEA Command Request Acknowledge Group Function 126464 Transmit Receive PGN List Group Function 126464 Transmit Receive PGN List Group Function 126996 Product Information 126996 Product Information 127245 Rudder 127250 Vessel Heading 127250 Vessel Heading 127258 Magnetic Variance 127488 Engine Parameters Rapid Update 128259 Speed Water Referenced 127489 Engine Parameters Dynamic 128267 Water Depth 127493 Transmission Parameters Dynamic 129025 Position Rapid Update 127498 Engine Parameters Static 129026 COG SOG Rapid Update 127505 Fluid Level 129029 GNSS Position Data GPSMAP 700 Series Installation Instructions Receive Transmit 128259 Speed Water Referenced 129283 Cross Track Error 128267 Water Depth 129284 Navigation Data 129038 AIS Class
18. ted in Taiwan Bail Mounting the Chartplotter Use the included bracket to bail mount the GPSMAP 700 series chartplotter You can route cables from under the mounting surface through the included bail mount bracket though it is not necessary See page 3 for instructions on installing the bail mount bracket without routing cables through the bracket Hardware included Tools required not included e Bail mount bracket e Jigsaw e Cable organization bracket Drill and drill bits 1 4 in 32 mm and s in 3 mm e Bail mount template Number 2 Phillips screwdriver Four 35 mm M 4 2 x 1 4 screws to secure the bail mount bracket Two 20 mm M 3 5 x 1 3 screws to secure the cable organization bracket To install the bail mount bracket with the cables routed through the bracket Using the included bail mount bracket template determine the best place to install the bracket Be sure to leave adequate clearance behind the chartplotter for the wiring NOTE To avoid interference mount the GPSMAP 700 series chartplotter at least 32 in 813 mm from a magnetic compass 2 The bail mount bracket template has adhesive on the back Remove the GPSMAP protective liner and apply the template to the location at which you want to install 700 series the bail mount bracket chartplotter Use a 1 1 4 in 32 mm drill bit to drill the pass through hole in the center of the template Use a use a t s in 3 mm drill bit to drill the s
19. w garmin com February 2010 Part Number 190 01155 02 Rev B Printed in Taiwan
Download Pdf Manuals
Related Search