Fujitsu Siemens Computers P17-2 Computer Monitor User Manual
Contents
1. Please change the display mode to 1280 x 1024 with 60 Hz Please change the display mode to 1600 x 1200 with 60 Hz Picture position not correct Picture is shaking 10 Check whether the main switch at the rear of the monitor is switched on Check whether the power cable on the monitor is connected correctly Check whether the computer is switched on Check whether the computer is switched on Check whether the data cable for the monitor is correctly attached to the monitor port on the computer Press any key on the computer keyboard the computer may be in energy saving mode Alter the brightness and or contrast until you get a picture Check whether the data cable for the monitor is correctly attached to the monitor port on the computer Check whether the computer is switched on The input signal horizontal frequency and refresh rate at the displayed input does not correspond to the technical monitor data gt Adjust the video frequency range using the computer software see documentation for your computer or your graphics card Adjust a different screen resolution using the computer software see documentation for your computer or your screen controller P17 2 P19 2 P20 2 1280 x 1024 1600 x 1200 The monitor recognises an undefined mode see the Technical data chapter gt Press the EXIT AUTO button to perform the auto adjustment of the screen Check whether the data cable for the monitor2. display format of the OSD menu Rotation With this function you switch the OSD menu from portrait mode to landscape mode and vice versa Off The OSD menu is displayed in portrait mode On The OSD menu is displayed in landscape mode Setting functions in the Advanced menu B E Calling the Advanced setting window Input select Selecting input signal With this function you switch the monitor from the analogue to the digital mode and vice versa when two signal sources are connected The condition is that the graphic card used supports this function Sharpness Adjusting the picture quality in case of interpolation With this function you set the sharpness of the interpolation filter Thus the display can be optimised for pictures or texts Resolution Displaying monitor data Notifier The optimum resolution for this monitor is 1280 x 1024 pixels With the function activated On a message appears on the screen after approx 30 seconds if a different resolution is set Change the resolution to 1280 x 1024 to achieve optimum picture quality With the function deactivated Off no message appears Factory Recall Activating the factory settings With this function all settings are reset to the factory settings without prompting for confirmation Press the SELECT MENU button to activate the function The Auto Processing message is displayed SCENICVIEW P17 2 P19 2 P20 2 Displaying information Calling the nformatio
3. is correctly attached to the monitor port on the computer Press the EXIT AUTO button to perform the auto adjustment of the screen SCENICVIEW P17 2 P19 2 P20 2 Having this problem Check the following points Picture is wrongly adjusted gt Press the SELECT MENU button to activate the function Factory Recall The Auto Processing message is displayed Picture disturbances vertical lines gt Press the EXIT AUTO button to perform the auto adjustment of the screen Picture disturbances horizontal lines gt Press the EXIT AUTO button to perform the auto picture noise adjustment of the screen The background lighting has a limited lifetime If your monitor display should become too dark the background lighting will have to be exchanged gt Please contact our help desk The screen becomes darker 11
4. Brightness Contrast setting window Brightness Setting the brightness of the display With this function you change the brightness of the background lighting Contrast Setting the contrast of the display With this function you modify the contrast of bright colour tones Black Level Setting the brightness of the display With this function you modify the contrast of dark colour tones Auto Level Setting the brightness of the display With this function you can automatically set the contrast Press the SELECT MENU button to activate the function If the contrast is set too high bright surfaces can no longer be distinguished from very bright surfaces If the contrast is set too low the maximum brightness will not be achieved SCENICVIEW P17 2 P19 2 P20 2 Adjusting size and position Calling the Image adjust setting window H Position Adjusting the horizontal position With this function you move the picture to the left or to the right V Position Adjusting the vertical position With this function you move the picture up or down Setting synchronisation With this function you adjust the picture width to eliminate vertical picture disturbances Eliminating picture interference With this function you fine tune your monitor to eliminate picture interference Adjusting the volume Calling the Audio setting window Volume Setting the volume for playback with the integrated loudspeakers Setting the volume for playback with t
5. Brightness mark another icon e g Image adjust mf Senma gt Press the SELECT MENU button to select Audio Black Level the highlighted icon Auto Level Colour E OSD Setup _ Advanced Information SCENICVIEW P17 2 P19 2 P20 2 The corresponding setting window here Image Adjust is displayed on the right hand side The first function H Position is highlighted 3 O FUJITSU comeurers gt f necessary press the w or a button to Brightness Contrast SIEMENS mark another function ES Press the SELECT MENU button to select fears HPosition the highlighted function V Position gt Press the w or a button to adjust the Clock value for the selected function Phase Colour gt Press the EXIT AUTO button to exit the function OSD Setup gt f necessary press the button w or a to _ mark another function or press the Macereed EE sia EXIT AUTO button to return to the main menu Information All changes are stored automatically If you want to change other settings select the corresponding function from the OSD main menu All possible adjustments of the main menu are described in the following operation some functions are not available as they are not required due to the digital il The OSD menu for analogue monitor operation is described in the following During digital transmission technology used Adjusting the brightness and contrast O 0 Calling the
6. Monitor English Operating Manual SCENICVIEW P17 2 P19 2 P20 2 FU ITSU COMPUTERS We make sure a SCENICVIEW P17 2 P19 2 P20 2 Ey Operation of the monitor The monitor offers the following possibilities that enable it to be optimally adjusted for the respective user and the respective situation Adjusting height rake and rotation The monitor height can be adjusted within a range of approx 2 5 inch 70 mm gt Grasp the monitor with both hands on the right and left edge of the casing and move it upward or downward The rake of the monitor can be adjusted by 2 forward and 35 back from its vertical position gt Grasp the monitor with both hands on the right and left edge of the casing and adjust it to the desired rake The monitor can be rotated by 60 from its centre position gt Grasp the monitor with both hands on the right and left edge of the casing and rotate it into the desired position SCENICVIEW P17 2 P19 2 P20 2 Adjusting portrait format The monitor can be turned from the wide format landscape mode into the high format position portrait mode gt Grasp the monitor with both hands on the right and left edge of the casing move it into the highest position and turn it clockwise until it is in the portrait position shown in the portrait mode This software is included in the delivery CD ROM and must i You must use corresponding software pivot software so th
7. an be set with the CD supplied gt Insert the supplied CD into the CD ROM drive gt Open the Readme file on the CD and follow the instructions in the file Your monitor should now already be properly adjusted If none of the above operating systems is used or minor corrections are to be made to the screen display then change the monitor settings with the OSD menu Changing the monitor settings with the buttons of the control panel SELECT MENU V m A INPUT EXIT AUTO 1 Buttons for the OSD menu 2 ON OFF switch On Screen display 3 Power indicator Use the buttons of the control panel to make the following monitor settings directly while the OSD menu is switched off Performing auto adjustment of the monitor gt Press the AUTO button for approx 1 second while the OSD menu is switched off The Auto Processing message is displayed Picture quality and position are set to optimum values for your system Selecting input signal D SUB DVI D gt Press the INPUT button for calling the Input select setting window gt Press the w or a button to select the desired input analogue D SUB or digital DVI D This setting window can also be called when the OSD menu is locked Activating deactivating muting gt Press the xi button to switch the sound off and on again A message is displayed that the action has been performed SCENICVIEW P17 2 P19 2 P20 2 Locking the OSD menu The OSD menu can be locked to pr
8. at the screen display is also be installed on your computer gt Inthe OSD menu you have the option of switching the OSD manually from landscape mode into portrait mode see section Monitor settings using the OSD menu To reset the monitor to the landscape mode the monitor must be turned counter clockwise The OSD display can be reset again in the OSD menu Switching the monitor on off The main switch at the rear and the ON OFF switch at the front are used for switching the monitor on and off gt Switch the monitor on with the main switch 4 at the rear 1 Buttons for the OSD menu On Screen display 2 ON OFF switch Power indicator 4 Main switch The power indicator 3 lights up blue when the monitor and computer are switched on The power indicator lights up orange when the monitor does not receive a video signal or is in the energy saving mode The power indicator goes off when the monitor is switched off SCENICVIEW P17 2 P19 2 P20 2 Changing the monitor settings When putting the monitor into operation for the first time the screen display should be optimally adapted to the screen controller used and adjusted in accordance with your needs Choosing basic monitor settings using the supplied software If one of the operating systems Windows 95 98 Windows NT Windows Me Windows 2000 Windows XP or OS 2 with Windows emulation installed is used the basic monitor settings c
9. event accidental or unauthorised changes to the monitor settings gt Press and hold the SELECT MENU button for a few seconds while you switch on the monitor with the ON OFF switch A message is displayed that the action has been performed Please proceed in the same manner to release the locked OSD menu again Locking the ON OFF button The ON OFF switch can be locked to prevent accidental or unauthorised changes to the monitor settings gt Press and hold both buttons w and a simultaneously for a few seconds A message is displayed that the action has been performed Please proceed in the same manner to release the locked ON OFF switch again Monitor settings using the OSD menu With the buttons on the control panel call up and use the integrated OSD On Screen display menu The OSD menu is available in different languages The English menu names are used in the following description default setting With the OSD function Language in the OSD Setup you can select another language To set the OSD menu perform the following steps gt Press the SELECT MENU button to activate the OSD menu The main menu appears on the screen on the left hand side with icons for the setting functions The first symbol Brightness Contrast is 00 FUJITSU courus highlighted In the right hand part of the display Brightness Contrast SIEMENS the associated functions are shown Bs f gt If necessary press the w or a button to Image adjust
10. he integrated loudspeakers volume for playback with the integrated loudspeakers Switching the loudspeakers off or on Setting colour temperature and colours Calling the Colour setting window Selecting the colour temperature The warmth of the screen colours is set using the colour temperature The colour temperature is measured in K Kelvin You can select from sRGB 6500 K 7500 K 9300 K Native and Custom Colour sRGB setting colour display according to the sRGB standard Native Original colour of the LCD display Custom Colour User defined colours In the user defined setting you can change the colour ratios of the basic colours red green blue as required SCENICVIEW P17 2 P19 2 P20 2 Setting display of the OSD menu Calling the OSD Setup setting window Language Setting language for the OSD menu With this function you choose between English default setting French German Italian and Spanish as the language for the OSD menu OSD Setting the horizontal position of the OSD menu H Position With this function you move the OSD menu to the left or to the right OSD Setting the vertical position of the OSD menu V Position With this function you move the OSD menu up or down OSD Setting the display duration of the OSD menu Timeout With this function you select a value from 10 to 120 seconds If the set time expires without a setting being made the OSD menu is automatically faded out OSD Setting the
11. n setting window With this function the model designation serial number resolution H V frequency input signal and polarity of the synchronisation signal are displayed Notes on ergonomic colour adjustment If you select colours for the display in your application programmes take note of the information below The primary colours blue and red on a dark background do not produce the minimum required contrast of 3 1 and are therefore not suitable for continuous text and data entry When using several colours for characters and background and giving the primary colours full modulation you can obtain very suitable colour combinations see the following table SESS ee Come Com Co e e omn gt Con e De e e EARE Colour combination very suitable Colour combination not suitable because colour locations are too close together thin characters are not identifiable or rigorous focusing is demanded of the human eye SCENICVIEW P17 2 P19 2 P20 2 Troubleshooting Should an error occur first check the following points If the distortion is still not eliminated the monitor should if possible be checked on another computer If you are unable to solve the problem please inform our help desk Having this problem Check the following points No screen display power indicator does not light No screen display power indicator lights Message No Signal Message Frequency out of range kHz Hz
Download Pdf Manuals
Related Search