Home

Ford 2006 Mustang Automobile User Manual

1. 37 Lights Handle a halogen headlamp bulb carefully and keep out of children s reach Grasp the bulb only by its plastic base and do not touch the glass The oil from your hand could cause the bulb to break the next time the headlamps are operated Install the new bulb in reverse order Replacing front parking lamp turn signal bulbs 1 Make sure the headlamp control is in the OFF position and open the hood 2 Locate the lamp assembly from underneath the vehicle and rotate the bulb socket counterclockwise and remove from lamp assembly 3 Pull the bulb straight out from the socket Install the new bulb in reverse order Replacing front parking lamp turn signal bulbs 1 Make sure the headlamp control is in the OFF position and open the hood 2 Locate the lamp assembly from underneath the vehicle and rotate the bulb socket counterclockwise and remove from lamp assembly 3 Pull the bulb straight out from the socket Install the new bulb in reverse order Replacing foglamp bulbs if equipped 1 Make sure the headlamp control is in the OFF position and open the hood 38 Lights 2 Remove the sight shield by loosening the six fasteners with a flat head screwdriver 3 Remove the two underhood bolts attaching the bumper cover next to the grill and then pull the cover grille foglamp assembly forward to access the foglamp b
2. e Base instrument cluster Press and release the RESET button on the cluster to toggle between odometer and trip odometer display To reset press and hold for less than 2 seconds e Optional instrument cluster 006 0 TRIP opga m Tachometer Indicates the engine speed in revolutions per minute Driving with your tachometer pointer continuously at the top of the scale may damage the engine Press and release the message center INFO button until TRIP mode appears in the display Press the RESET button to reset e Base instrument cluster e Optional instrument cluster 17 Instrument Cluster Battery voltage gauge if equipped Indicates the battery voltage when the ignition is in the ON position If the pointer moves and stays outside the normal operating range have the vehicle s electrical system checked by your authorized dealer as soon as possible Engine oil pressure gauge if equipped Indicates engine oil H pressure The needle should stay in the normal operating range Y between L and H If the needle falls below the normal range stop the vehicle turn off the engine and check the engine oil level Add oil if needed If the oil level is correct and gauge reads no low oil pressure shut down the engine immediately and contact your dealer for service or by a qualified technician Fuel gauge Indicates approximately how much fuel is left in the fuel tank wh
3. c ir P1000 J _ 2 2 6 2 Y wm if i 6 A x La T ate Ro ny ete ee Ss Sam wee DB 0 sx ma S nhs 25 Warning lights and gauges can alert you to a vehicle condition that may become serious enough to cause extensive repairs A warning light may illuminate when a problem exists with one of your vehicle s functions Many lights will illuminate when you start your vehicle to make sure the bulbs work If any light remains on after starting the vehicle refer to the respective system warning light for additional information 10 Instrument Cluster Service Engine Soon The Service Engine Soon indicator light C illuminates when the ignition is first turned to the ON position to check the bulb Solid illumination after the engine is started indicates the On Board Diagnostics System OBD II has detected a malfunction Refer to On board diagnostics OBD II in the Maintenance and Specifications chapter If the light is blinking engine misfire is occurring which could damage your catalytic converter Drive in a moderate fashion avoid heavy acceleration and deceleration and have your vehicle serviced immediately by your authorized dealer Under engine misfire conditions excessive exhaust temperatures could damage the catalytic converter the fuel system interior floor coverings or other vehicle components possibly causing a fire Illuminates when the fuel cap may not be properly installed
4. Some warning lights will briefly illuminate See Warning lights and chimes in the Instrument Cluster chapter for more information regarding the warning lights Starting the engine 1 Turn the key to 3 ON without turning the key to 4 START If there is difficulty in turning the key rotate the steering wheel until the key turns freely 2 Turn the key to 4 START then release the key as soon as the engine starts Note If the engine does not start within five seconds on the first try turn the key to OFF wait 10 seconds and try again If the engine still fails to start press and hold the accelerator to the floor and try again this will allow the engine to crank with the fuel shut off in case the engine is flooded with fuel Guarding against exhaust fumes Carbon monoxide is present in exhaust fumes Take precautions to avoid its dangerous effects If you smell exhaust fumes inside your vehicle have your dealer inspect your vehicle immediately Do not drive if you smell exhaust fumes 149 Driving Important ventilating information If the engine is idling while the vehicle is stopped for a long period of time open the windows at least one inch 2 5 cm or adjust the heating or air conditioning to bring in fresh air USING THE ENGINE BLOCK HEATER IF EQUIPPED An engine block heater warms the engine coolant which aids in starting and heater defroster performance Use of an engine block heater is strongly rec
5. 107 Operation anenee 99 106 passenger airbag 99 106 Side airbag ceeeeeeeeeseeeees 105 Antifreeze see Engine GOLAU sc cosecesesvecrtentasanasnetcoiecse 208 Anti lock brake system see Brakes 150 151 Anti theft System ecce 74 Audio system see Radio 19 22 Automatic transmission 154 driving an automatic Overdrive ooo ceeececcccececeeeesteeeeeees 156 fluid adding 0 0 226 fluid checking 226 fluid refill capacities 230 fluid specification 00 234 Auxiliary power point 0 43 Axle lubricant specifications 232 234 refill capacities 0 0 00 230 traction lok osensererenneiereni 154 B Battery cccccccsccccsesseceeenseeeeees 206 acid treating emergencies 206 jumping a disabled battery 176 maintenance free sses 206 Index replacement specifications 228 SOFVICING ssdeccssvaediceatebistizsinceties 206 BeltMinder seeen 92 Brake ccccecceeeesceesesessecesseeeseeeees 150 anti lock oec 150 151 anti lock brake system ABS warning light fluid checking and adding 225 230 fluid refill capacities fluid specifications 232 234 lubricant specifications 232 234 DATKING sess seceessancancaysaeesvcens aves 151 Shift Mterlock srera 154 Break in period sscricgrerenisese 5 Bulb sc 32 323se aaceieseeasneacenis ose 36 C Capacities for refilling fluids 230
6. Air filter assembly neal pa geal Ae i SIP SID a Q Engine oil filler cap Brake fluid reservoir Power steering fluid reservoir T Engine coolant reservoir 8 Windshield washer fluid reservoir 9 Power distribution box 199 Maintenance and Specifications WINDSHIELD WASHER FLUID lt gt Add fluid to fill the reservoir if the level is low In very cold weather do not fill the reservoir completely Only use a washer fluid that meets Ford specification WSB M8B16 A2 Do not use any special washer fluid such as windshield water repellent type fluid or bug wash They may cause squeaking chatter noise streaking and smearing Refer to Lubricant specifications in this chapter State or local regulations on volatile organic compounds may restrict the use of methanol a common windshield washer antifreeze additive Washer fluids containing non methanol antifreeze agents should be used only if they provide cold weather protection without damaging the vehicle s paint finish wiper blades or washer system If you operate your vehicle in temperatures below 40 F 4 5 C use washer fluid with antifreeze protection Failure to use washer fluid with antifreeze protection in cold weather could result in impaired windshield vision and increase the risk of injury or accident Note Do not put washer fluid in the engine coolant reservoir Washer fluid placed
7. Blue and Exit options Pressing SETUP will increment the proportion of the color being adjusted Try many combinations and record your favorites To Save and Exit MyColor adjust hold RESET for 3 seconds when prompted Pressing RESET for less than 3 seconds will cycle back through the color components Units English Metric 1 Select this function from the SETUP menu for the current units UNITS to be displayed TEA 2 Press the RESET control to gt ENG METRIC change from English to Metric Display Mode 1 Select this function from the SETUP menu to select the Display i y DISPLAY MODE 2 Single Mode will display only the SINGLE gt DUAL selected function Dual Mode will display the selected function and the odometer 56 Language 1 Select this function from the SETUP menu for the current language to be displayed 2 Pressing the RESET control cycles the message center through each of the language choices 3 Press and hold the RESET control to set the language choice Info menu This control displays the following control displays e Odometer e Trip odometer e Distance to Empty e Average Fuel Economy e Instantaneous Fuel Economy e Fuel Used e Trip Elapsed Drive Time e Average Speed e Blank Display Odometer Trip odometer Driver Controls ENGLISH RESET FOR NEU J FOR ENGLISH HOLD RESET ay f SET TO i ENGLISH Refer to Gauges in the In
8. Cell phone USE ceceesseeeeeneeees 7 Changing a tire eee 171 Child safety restraints 108 child safety belts 0 0 0 0 108 Child safety seats cccccee 112 attaching with tether straps 116 It front SCAU sisscidesccsadvsxevevscesacs 113 i rear seat sccvssieircevesens abet 113 Cleaning your vehicle engine compartment 190 instrument panel 00 193 CETOL henri 193 Plastic parts wo eee 192 WASHING bussare ur 189 WAKING Sepe E S 189 WIEEIS vs cidssiassacsdeasuriessestesssseaes 190 wiper blades cccceeeeeeeees 192 Clock adjust 6 CD Tn Gash eicescecen eotiesestves Gest 24 AM FM CD sesser 20 Index Clutch AVG EE E ETETA 225 operation while driving 159 recommended shift speeds 160 CONSOLE sunekin gnar 44 Controls POWET SEaren 78 Convertible cececeeseeeeetees 49 CLEANING sssyccivsivesieteritresngceeadestes 192 installation of the boot 51 lowering the convertible top 49 raising the convertible top 52 Coolant checking and adding 208 refill capacities 1 00 212 230 specifications 68 232 234 Cruise control see Speed control 0008 47 Customer Assistance 00 162 Ford Extended Service Plai stescaetenereteriadesneoee esas 186 Getting assistance outside the U S and Canada eeeees 186 Getting roadside assistance 162 Getting the service you NOOO EE 182
9. Lock Lubricant Lock cylinders 232 Ford part Ford number specification ESR M13P4 A XG 4 or XL 5 ESB M1C93 B VC 7 A U S WSS M97B51 A1 except CA OR and NM VC 7 B CA OR and NM XO 5W20 QSP US CXO 5W20 LSP12 Canada WSS M2C 930 A with API Certification Mark XO 5W30 QSP US CXO 5W30 LSP12 Canada WSS M2C 929 A and API Certification Mark Maintenance and Specifications Item Ford part Ford part Ford name number specification Power steering Motorcraft XT 2 QDX MERCON fluid MERCON ATF Rear Axle Motorcraft SAE XY 75W140 QL WSP M2C192 A Lubricant 75W 140 Synthetic Rear Axle Lubricant Automatic Motorcraft XT 5 QM MERCON V transmission MERCON V fluid ATF Manual Motorcraft XT 2 QDX MERCON transmission MERCON ATF fluid Disc brake Motorcraft XG 3 A ESE M1C171 A caliper rails Silicone Brake Caliper Grease and Dielectric Compound Windshield Motorcraft ZC 32 A WSB M8B16 A2 washer fluid Premium Windshield Washer Concentrate Add 4 oz 118 ml of Additive Friction Modifier XL 3 or equivalent meeting Ford specification EST M2C118 A for complete refill of Traction Lok axles Ford design rear axles contain a synthetic lubricant that does not require changing unless the axle has been submerged in water Ensure the correct automatic transmission fluid is used MERCON and MERCON V are not interchangeable DO NOT mix MERCON and MERCON V Ref
10. To ready the on board diagnostics system for I M testing a minimum of 30 minutes of city and highway driving is necessary as described below e First at least 10 minutes of driving on an expressway or highway e Next at least 20 minutes driving in stop and go city type traffic with at least four idle periods Allow the vehicle to sit for at least eight hours without starting the engine Then start the engine and complete the above driving cycle The engine must warm up to its normal operating temperature Once started do not turn off the engine until the above driving cycle is complete 224 Maintenance and Specifications POWER STEERING FLUID Check the power steering fluid Refer to the scheduled maintenance guide for the service interval cS LLY schedules If adding fluid is 054 ISSO necessary use only MERCON i L ial ATF 1 Start the engine and let it run until it reaches normal operating temperature the engine coolant temperature gauge indicator will be near the center of the normal area between H and C 2 While the engine idles turn the steering wheel to its furthest point until it stops left and right several times 3 Turn the engine off 4 Check the fluid level in the reservoir It should be between the MIN and MAX lines Do not add fluid if the level is in this range N NY pi OLY gt eS A FD 5 If the fluid is low add fluid in small amounts continuously checking the le
11. a vu N Gn e This position allows for all forward gears except Overdrive e O D OFF lamp is illuminated 0 D OFF e Provides engine braking e Use when driving conditions cause excessive shifting from O D to other gears Examples city traffic hilly terrain heavy loads trailer towing and when engine braking is required 157 Driving e To return to Overdrive mode press the transmission control switch The O D OFF lamp will not be illuminated e Overdrive mode is automatically returned each time the key is turned off 3 Third This position allows for third gear only e Provides engine braking e To return to D Drive without Overdrive move the transmission shift lever into the D Drive position e Selecting 3 Third at higher speeds will cause the transmission to downshift to third gear at the appropriate vehicle speed 2 Second This position allows for second gear only e Provides engine braking e Use to start up on slippery roads e To return to D Drive without Overdrive or 3 Third move the transmission shift lever into the D Drive or 3 Third position e Selecting 2 Second at higher speeds will cause the transmission to downshift to second gear at the appropriate vehicle speed 1 First This position allows for first gear only e Provides maximum engine braking e Will not downshift into first gear at high speeds will cause the transmission to downshift to a lower gear then all
12. menu mode to select various settings 6 Text In CD mode this feature reads and displays track song title artist name and album title 7 Shuffle Press to play the tracks in random order 25 Entertainment Systems 8 FOLDER Press to access next folder on MP3 discs if folders are available 9 FOLDER press to access the previous folder on MP3 discs if folders are available 10 Fast forward Press to manually advance in a CD track 11 Rewind Press to manually reverse in a CD track 12 Memory presets To set a station Select frequency band AM FM tune to a station press and hold a preset button until sound returns 13 Sean Press for a brief sampling of radio stations or CD tracks Press again to stop 14 Seek Press to access the previous strong station or track 15 AM FM Press to select AM FM frequency band 16 ON OFF Volume Press to turn ON OFF Turn to increase decrease volume If the volume is set above a certain level and the ignition is turned off the volume will come back on at a Oban VOL PUSH nominal listening level when the ignition switch is turned back on 17 CD Press to enter CD mode If a CD is already loaded into the system CD play will begin where it ended last 26 d Entertainment Systems 18 LOAD Press to begin the CD load sequence When the radio a prompts to select a slot use the toan presets to select the desired slot to l
13. s main electrical systems from overloads Do not probe the contacts for the fuses and relays in the power distribution box as damage will occur causing improper or loss of electrical functionality Always disconnect the battery before servicing high current fuses To reduce risk of electrical shock always replace the cover to the Power Distribution Box before reconnecting the battery or refilling fluid reservoirs If the battery has been disconnected and reconnected refer to the Battery section of the Maintenance and Specifications chapter 167 Roadside Emergencies Jo ae ARAR ABBE eE ARAR HARAR aL Aie del IL The high current fuses are coded as follows Location Rating Description T Climate control blower ooo BT 40a Coolingfan i O ooo TOA Starter S PT soar Driver front window motor __ 30A Rear amplifier Shaker 1000 radio a Anti lock Brake System ABS 1 30A Rear amplifier Shaker 1000 radio 11 30A Driver rear window motor a ae ee 12 30A Passenger rear window motor a a ee 168 Fuse Relay Location 18 14 15 16 20 21 22 23 24 25 26 27 28 29 30 3l 32 33 34 35 36 3T 38 39 40 Fuse Amp Rating 40A 30A 30A Mini relay Mini relay Mini relay Mini relay Mini relay Mini relay Mini relay Mini relay Mini relay Micro relay 15A Roadside Emergencies Power Distribution Box Description Convertible top Fro
14. Check for holes or cuts that may permit air leakage from the tire and make necessary repairs Also inspect the tire sidewalls for cracking cuts bruises and other signs of damage or excessive wear If internal damage to the tire is suspected have the tire demounted and inspected in case it needs to be repaired or replaced For your safety tires that are damaged or show signs of excessive wear should not be used because they are more likely to blow out or fail 126 Tires Wheels and Loading Improper or inadequate vehicle maintenance can cause tires to wear abnormally Inspect all your tires including the spare frequently and replace them if one or more of the following conditions exist Tire wear When the tread is worn down to 1 16th of an inch 2 mm tires must be replaced to help prevent your vehicle from skidding and hydroplaning Built in treadwear indicators or wear bars which look like narrow strips of smooth rubber across the tread will appear on the tire when the tread is worn down to 1 16th of an inch 2 mm s 4 When the tire tread wears down to the same height as these wear bars the tire is worn out and must be replaced Damage Periodically inspect the tire treads and sidewalls for damage such as bulges in the tread or sidewalls cracks in the tread groove and separation in the tread or sidewall If damage is observed or suspected have the tire inspected by a tire professional
15. Do not park idle or drive your vehicle in dry grass or other dry ground cover The emission system heats up the engine compartment and exhaust system which can start a fire Illumination of the C indicator charging system warning light or the temperature warning light fluid leaks strange odors smoke or loss of engine power could indicate that the emission control system is not working properly Exhaust leaks may result in entry of harmful and potentially lethal fumes into the passenger compartment Do not make any unauthorized changes to your vehicle or engine By law vehicle owners and anyone who manufactures repairs services sells leases trades vehicles or supervises a fleet of vehicles are not permitted to intentionally remove an emission control device or prevent it from working Information about your vehicle s emission system is on the Vehicle Emission Control Information Decal located on or near the engine This decal identifies engine displacement and gives some tune up specifications Please consult your Warranty Guide for complete emission warranty information On board diagnostics OBD II Your vehicle is equipped with a computer that monitors the engine s emission control system This system is commonly known as the On Board Diagnostics System OBD II This OBD II system protects the environment by ensuring that your vehicle continues to meet government emission standards The OBD II system also assists your
16. Ford Motor Company of Canada Limited Service Publications P O Box 1580 Station B Mississauga Ontario L4Y 4G3 REPORTING SAFETY DEFECTS U S ONLY If you believe that your vehicle has a defect which could cause a crash or could cause injury or death you C Sond should immediately inform the National Highway Traffic Safety Administration NHTSA in addition to notifying Ford Motor Company If NHTSA receives similar complaints it may open an investigation and if it finds that a safety defect exists in a group of vehicles it may order a recall and remedy campaign However NHTSA cannot become involved in individual problems between you your dealer or Ford Motor Company To contact NHTSA you may either call the Auto Safety Hotline toll free at 1 800 424 9393 or 366 0123 in the Washington D C area or write to NHTSA 400 Seventh Street U S Department of Transportation Washington D C 20590 You can also obtain other information about motor vehicle safety from the Hotline 188 Cleaning WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutral pH shampoo such as Motorcraft Detail Wash ZC 3 A which is available from your authorized dealer e Never use strong household detergents or soap such as dish washing or laundry liquid These products can discolor and spot painted surfaces e Never wash a vehicle that is hot to the touch or during exposure to strong direc
17. OFF LOCK position to the 3 ON position Keep the ignition in the 3 ON position for at least one second but no more than 10 seconds 3 Turn the ignition to the 1 OFF LOCK position and remove the coded key from the ignition 4 Within ten seconds of removing the previously programmed coded key insert the other previously programmed coded key into the ignition 5 Turn the ignition from the 1 OFF LOCK position to the 3 ON position Keep the ignition in the 3 ON position for at least one second but not more than 10 seconds 6 Turn the ignition to the 1 OFF LOCK position and remove the second key from the ignition 7 Within twenty seconds of removing the previously programmed coded key insert the unprogrammed key new valet key into the ignition 8 Turn the ignition from the 1 OFF LOCK position to the 3 ON position Keep the ignition in the 3 ON position for at least one second 9 Your new unprogrammed key is now programmed If the key has been successfully programmed it will start the vehicle s engine and the theft indicator light will illuminate for three seconds and then go out If the key was not successfully programmed it will not start your vehicle s engine and the theft indicator light will flash on and off rapidly If failure repeats bring your vehicle to your authorized dealer to have the new key s programmed 73 Locks and Security To program additional new unprogrammed key s repe
18. Seating and Safety Restraints The belt guide is secured to the side shield by fastening the magnet on the guide strap to the magnet on the side shield 1 Insert the belt tongue into the proper buckle the buckle closest to the direction the tongue is coming P from until you hear a snap and feel a it latch Make sure the tongue is securely fastened in the buckle Ga D J 2 To unfasten push the release button and remove the tongue from the buckle p PA d e a LA The center of the rear seat is NOT designed as a seating position The LATCH anchors were not designed to be used with a child seat in the center position and there is no tether anchor available at the center Attempted use of the center as a seating position will increase the risk of injury or death in the event of a collision 87 Seating and Safety Restraints Energy Management Feature e This vehicle has a safety belt system with an energy management feature at the front seating positions to help further reduce the risk of injury in the event of a head on collision e This safety belt system has a retractor assembly that is designed to pay out webbing in a controlled manner This feature is designed to help reduce the belt force acting on the occupant s chest After any vehicle collision the safety belt system at all outboard seating positions except driver which has no automatic locking retractor feature must be checked by an aut
19. accept the BBB AUTO LINE decision then Ford must abide by the accepted decision as well If the arbitrator has decided in your favor and you accept the decision the BBB AUTO LINE program will contact you to ensure that Ford has complied with the decision in a timely manner Disputes submitted to the BBB AUTO LINE program are usually decided within forty days after you file your claim with the BBB To file a claim with the BBB AUTO LINE you will be asked for your name and address information about your vehicle information about your concerns and any steps you have already taken to try to resolve them You can get more information by calling BBB AUTO LINE at 1 800 428 3718 or writing to BBB AUTO LINE 4200 Wilson Boulevard Suite 800 Arlington Virginia 22203 1833 Note Ford Motor Company reserves the right to change eligibility limitations modify procedures or to discontinue this process at any time without notice and without obligation UTILIZING THE MEDIATION ARBITRATION PROGRAM CANADA ONLY For vehicles delivered to authorized Canadian dealers In those cases where you continue to feel that the efforts by Ford of Canada and the authorized dealer to resolve a factory related vehicle service concern have been unsatisfactory Ford of Canada participates in an impartial third party mediation arbitration program administered by the Canadian Motor Vehicle Arbitration Plan CAMVAP 185 Customer Assistance The CAMVAP program i
20. against the convertible top and windows may cause water leaks and possible seal damage 192 Cleaning INSTRUMENT PANEL AND CLUSTER LENS Clean the instrument panel with a damp cloth then with a clean dry cloth or use Motorcraft Dash amp Vinyl Cleaner ZC 38 A e Avoid cleaners or polish that increase the gloss of the upper portion of the instrument panel The dull finish in this area helps protect the driver from undesirable windshield reflection Do not use chemical solvents or strong detergents when cleaning the steering wheel or instrument panel to avoid contamination of the airbag system e Be certain to wash or wipe your hands clean if you have been in contact with certain products such as insect repellent and suntan lotion in order to avoid possible damage to the interior painted surfaces INTERIOR For fabric carpets cloth seats safety belts and seats equipped with side airbags e Remove dust and loose dirt with a vacuum cleaner e Remove light stains and soil with Motorcraft Professional Strength Carpet amp Upholstery Cleaner ZC 54 e If grease or tar is present on the material spot clean the area first with Motorcraft Spot and Stain Remover ZC 14 e If a ring forms on the fabric after spot cleaning clean the entire area immediately but do not oversaturate or the ring will set e Do not use household cleaning products or glass cleaners which can stain and discolor the fabric and affect the flame reta
21. always place children under age 12 in the rear seat of your vehicle Accident statistics suggest that children are safer when properly restrained in the rear seating positions than in the front seating position Never let a passenger hold a child on his or her lap while the vehicle is moving The passenger cannot protect the child from injury in a collision Always follow the instructions and warnings that come with any infant or child restraint you might use Children and safety belts If the child is the proper size restrain the child in a safety seat Children who are too large for child safety seats as specified by your child safety seat manufacturer should always wear safety belts Follow all the important safety restraint and airbag precautions that apply to adult passengers in your vehicle If the shoulder belt portion of a combination lap and shoulder belt can be positioned so it does not cross or rest in front of the child s face or neck the child should wear the lap and shoulder belt Moving the child closer to the center of the vehicle may help provide a good shoulder belt fit Do not leave children unreliable adults or pets unattended in your vehicle 108 Seating and Safety Restraints Child booster seats Children outgrow a typical convertible or toddler seat when they weigh 40 lb 18 kg and are around 4 years of age Although the lap shoulder belt will provide some protection these children are still too s
22. and Antifreeze Tester 014 R1060 The level of coolant should be maintained at the FULL COLD level or within the COLD FILL RANGE in the coolant reservoir If the level falls below add coolant per the instructions in the Adding engine coolant section Your vehicle was factory filled with a 50 50 engine coolant and water concentration If the concentration of coolant falls below 40 or above 60 the engine parts could become damaged or not work properly A 50 50 mixture of coolant and water provides the following e Freeze protection down to 34 F 36 C e Boiling protection up to 265 F 129 C e Protection against rust and other forms of corrosion e Enables calibrated gauges to work properly 208 Maintenance and Specifications When the engine is cold check the level of the engine coolant in the Pr amp S reservoir aan l NALEAN COLD FILL RANGE e The engine coolant should be at the FULL COLD level or within the COLD FILL RANGE as listed on the engine coolant reservoir depending upon application e Refer to scheduled maintenance information for service interval schedules Be sure to read and understand Precautions when servicing your vehicle in this chapter If the engine coolant has not been checked at the recommended interval the engine coolant reservoir may become low or empty If the reservoir is low or empty add engine coolant to the reservoir Refer to Adding
23. and pull the switches to open and close windows e Push down to the first detent gt and hold the switch to open AUTO AUTO e Pull up to the first detent and hold the switch to close 44 Driver Controls Express down One Touch Down Front windows only Allows the driver and passenger s window to open fully without holding the control down Push the switch completely down to the second detent and release quickly The window will open fully Momentarily press the switch to any position to stop the window operation Express Up One Touch Up Front windows only Allows the driver and passenger s window to close fully without holding the control up Pull the switch completely up to the second detent and release quickly The window will close fully Momentarily press the switch to any position to stop the window operation Restoring the Express up functionality Front windows only Under low battery power conditions Express Up only functionality may be lost To reset this function after restoring full battery power pull the switch to the Express Up position hold the switch until the glass reaches the stall position and continue to hold for 2 seconds Push the window switch DOWN and operate the window to the full down position Express UP will now be functional Perform Express UP re calibration with door closed only Calibrating with door open will cause the window to conti
24. area of your vehicle that is not equipped with seats and safety belts Be sure everyone in your vehicle is in a seat and using a safety belt properly 85 Seating and Safety Restraints In a rollover crash an unbelted person is significantly more likely to die than a person wearing a safety belt Each seating position in your vehicle has a specific safety belt assembly which is made up of one buckle and one tongue that are designed to be used as a pair 1 Use the shoulder belt on the outside shoulder only Never wear the shoulder belt under the arm 2 Never swing the safety belt around your neck over the inside shoulder 3 Never use a single belt for more than one person Always transport children 12 years old and under in the back seat and always properly use appropriate child restraints Safety belts and seats can become hot in a vehicle that has been closed up in sunny weather they could burn a small child Check seat covers and buckles before you place a child anywhere near them Combination lap and shoulder belts The belt guide is intended to improve access to the safety belt and to allow access to the rear seat Before fastening the safety belt make sure lower portion of the lap and shoulder belt passes underneath the belt guide at the bottom of the seatback Pull the magnets apart to release the belt guide and move the lap and shoulder belt out of the way of passengers entering and exiting the rear seats 86
25. customer warranty may be void for any damage to the fuel system if an authorized Motorcraft fuel filter is not used ESSENTIALS OF GOOD FUEL ECONOMY Measuring techniques Your best source of information about actual fuel economy is you the driver You must gather information as accurately and consistently as possible Fuel expense frequency of fill ups or fuel gauge readings are NOT accurate as a measure of fuel economy We do not recommend taking fuel economy measurements during the first 1 000 miles 1 600 km of driving engine break in period You will get a more accurate measurement after 2 000 miles 3 000 miles 3 000 km 5 000 km Filling the tank The advertised fuel capacity of the fuel tank on your vehicle is equal to the rated refill capacity of the fuel tank as listed in the Refill capacities section of this chapter The advertised capacity is the amount of the indicated capacity and the empty reserve combined Indicated capacity is the difference in the amount of fuel in a full tank and a tank when the fuel gauge indicates empty Empty reserve is the small amount of fuel remaining in the fuel tank after the fuel gauge indicates empty The amount of usable fuel in the empty reserve varies and should not be relied upon to increase driving range When refueling your vehicle after the fuel gauge indicates empty you might not be able to refuel the full amount of the advertised capacity of the fuel tank due to the empty reserve
26. end of the vehicle to the tire being changed If the vehicle slips off the jack you or someone else could be seriously injured Do not attempt to change a tire on the side of the vehicle close to moving traffic Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel Before changing the tire 1 Park on a level surface 2 Activate the hazard flashers 3 Place the gearshift lever in P Park automatic transmission or R Reverse manual transmission 4 Set the parking brake 5 Turn off the ignition To change the tire Note Passengers should not remain in the vehicle when the vehicle is being jacked 173 Roadside Emergencies 1 Block both the front and rear of the wheel diagonally opposite the flat tire For example if the left _ St front tire is flat block the right rear Z wheel s 2 2 Remove the lug wrench spare tire and jack 3 Remove the center ornament if equipped from the wheel Loosen each wheel lug nut one half turn counterclockwise but do not remove them until the wheel is raised off the ground 174 Roadside Emergencies 4 Put the jack in the jack notch next to the tire you are changing Turn the jack handle clockwise until the wheel is completely off the ground Never use the rear differential as a jacking point To lessen the risk of personal injury do not put any part of your body un
27. engine coolant in this chapter Note Automotive fluids are not interchangeable do not use engine coolant antifreeze or windshield washer fluid outside of its specified function and vehicle location Adding engine coolant When adding coolant make sure it is a 50 50 mixture of engine coolant and distilled water Add the mixture to the coolant reservoir when the engine is cool until the appropriate fill level is obtained Do not add engine coolant when the engine is hot Steam and scalding liquids released from a hot cooling system can burn you badly Also you can be burned if you spill coolant on hot engine parts 209 Maintenance and Specifications Do not put engine coolant in the windshield washer fluid container If sprayed on the windshield engine coolant could make it difficult to see through the windshield e Add Motorcraft Premium Gold Engine Coolant yellow colored VC 7 A U S except CA OR and NM VC 7 B CA OR and NM meeting Ford Specification WSS M97B51 Al1 Note Use of Motorcraft Cooling System Stop Leak Pellets VC 6 may darken the color of Motorcraft Premium Gold Engine Coolant from yellow to golden tan e Do not add mix an orange colored extended life coolant such as Motorcraft Specialty Orange Engine Coolant VC 2 and VC 3 US or CXC 209 Canada meeting Ford specification WSS M97B44 D with the factory filled coolant Mixing Motorcraft Specialty Orange Engine Coolant or any orange colored extend
28. latched An unlatched seat may become dangerous in the event of a sudden stop or collision Adjustable head restraints Your vehicle s seats are equipped with head restraints which are vertically adjustable The purpose of these head restraints is to help limit head motion in the event of a rear collision To properly adjust your head restraints lift the head restraint so that it is located directly behind your head or as close to that position as possible Refer to the following to raise and lower the head restraints 76 Seating and Safety Restraints Lift the head restraint to raise the E Ach l l To lower the head restraint press the button located on the driver s side post Adjusting the front manual seat ee if equipped Pe x Never adjust the driver s seat or seatback when the vehicle is moving Always drive and ride with your seatback upright and the lap belt snug and low across the hips Lift handle to move seat forward or backward 77 Seating and Safety Restraints Pull lever up to adjust the angle of the seatback Four way seat adjust driver side only Pump the handle upwards to raise the cushion and pump downward to lower the cushion to the desired location Using the power lumbar support if equipped The power lumbar control is located on the top of the seat side shield Press one side of the control to increase lower back firmness Press the other side of the cont
29. match the new wheel diameter Location of the tire label You will find a Tire Label containing tire inflation pressure by tire size and other important information located on the B Pillar or the edge of the driver s door Refer to the payload description and graphic in the Vehicle loading with and without a trailer section 135 Tires Wheels and Loading SNOW TIRES AND CHAINS Driving too fast for conditions creates the possibility of loss of vehicle control Driving at very high speeds for extended periods of time may result in damage to vehicle components Snow tires must be the same size and grade as the tires you currently have on your vehicle The tires on your vehicle have all weather treads to provide traction in rain and snow However in some climates you may need to use snow tires and chains Use chains on the tires only in an emergency or if the law requires them Follow these guidelines when using snow tires and chains e Chains may damage aluminum wheels e Use only SAE Class S chains with P215 65R16 tires on the rear of the vehicle only e Do not use tire chains with size P235 55R17 or 235 50R18 tires Use of SAE Class S chains or other chain types may damage your vehicle Install chains securely verifying that the chains do not touch any wiring brake lines or fuel lines e Drive cautiously If you hear the chains rub or bang against your vehicle stop and re tighten the chains If this does not work
30. miles 80 km thoroughly check your hitch electrical connections and trailer wheel lug nuts e To aid in engine transmission cooling and A C efficiency during hot weather while stopped in traffic place the gearshift lever in P Park automatic transmission or N Neutral manual transmissions 144 Tires Wheels and Loading e Vehicles with trailers should not be parked on a grade If you must park on a grade place wheel chocks under the trailer s wheels RECREATIONAL TOWING ALL WHEELS ON THE GROUND Follow these guidelines for your specific powertrain combination to tow your vehicle with all four wheels on the ground such as behind a recreational vehicle These guidelines are designed to ensure that your transmission is not damaged due to insufficient lubrication All Rear Wheel Drive RWD vehicles This applies to all cars and 4x2 trucks sport utilities with rear wheel drive capability e Place the transmission in N Neutral e Maximum speed is 35 mph 56 km h e Maximum distance is 50 miles 80 km If a distance of 50 miles 80 km or a speed of 35 mph 56 km h must be exceeded you must disconnect the driveshaft Ford Motor Company recommends the driveshaft be removed installed only by a qualified technician at an authorized dealer See your authorized dealer for driveshaft removal installation Improper removal installation of the driveshaft can cause transmission fluid loss damage to the driveshaft and int
31. not start your vehicle in a closed garage or in other enclosed areas Exhaust fumes can be toxic Always open the garage door before you start the engine See Guarding against exhaust fumes in this chapter for more instructions If you smell exhaust fumes inside your vehicle have your dealer inspect your vehicle immediately Do not drive if you smell exhaust fumes Important safety precautions A computer system controls the engine s idle revolutions per minute RPM When the engine starts the idle RPM runs higher than normal in order to warm the engine If the engine idle speed does not slow down automatically have the vehicle checked Do not allow the vehicle to idle for more than 10 minutes at the higher engine RPM Before starting the vehicle 1 Make sure all vehicle occupants have buckled their safety belts For more information on safety belts and their proper usage refer to the Seating and Safety Restraints chapter 2 Make sure the headlamps and vehicle accessories are off If starting a vehicle with an automatic transmission 147 Driving e Make sure the gearshift is in P wui I e Make sure the parking brake is set If starting a vehicle with a manual transmission e Make sure the parking brake is set e Push the clutch pedal to the floor 148 Driving 3 Turn the key to 3 ON without turning the key to 4 START
32. numbers 228 Refill capacities 230 Lubricant specifications 232 Accessories 239 Index 241 All rights reserved Reproduction by any means electronic or mechanical including photocopying recording or by any information storage and retrieval system or translation in whole or part is not permitted without written authorization from Ford Motor Company Ford may change the contents without notice and without incurring obligation Copyright 2005 Ford Motor Company Introduction CALIFORNIA Proposition 65 Warning WARNING Engine exhaust some of its constituents and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm In addition certain fluids contained in vehicles and certain products of component wear contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm CONGRATULATIONS Congratulations on acquiring your new Ford Please take the time to get well acquainted with your vehicle by reading this handbook The more you know and understand about your vehicle the greater the safety and pleasure you will derive from driving it For more information on Ford Motor Company and its products visit the following website e In the United States www ford com e In Canada www ford ca e In Australia www ford com au e In Mexico www ford com mx Additional owner information is give
33. pressure when you get to the pump It is normal for tires to heat up and the air pressure inside to go up as you drive Never bleed or reduce air pressure when tires are hot 2 Remove the cap from the valve on one tire then firmly press the tire gauge onto the valve and measure the pressure with the tire gauge 3 Add enough air to reach the recommended air pressure Note If you overfill the tire release air by pushing on the metal stem in the center of the valve Then recheck the pressure with your tire gauge 4 Replace the valve cap 5 Repeat this procedure for each tire including the spare Note Some spare tires operate at a higher inflation pressure than the other tires For T type mini spare tires see T7 Type Mini Spare Tire Information section for description Store and maintain at 60psi 4 15 bars For Full Size and Dissimilar spare tires see Dissimilar Spare Tive Wheel Information section for description Store and maintain at the higher of the front and rear inflation pressure as shown on the Tire Label 6 Visually inspect the tires to make sure there are no nails or other objects embedded that could poke a hole in the tire and cause an air leak 7 Check the sidewalls to make sure there are no gouges cuts or bulges TIRE CARE Inspecting your tires Periodically inspect the tire treads for uneven or excessive wear and remove objects such as stones nails or glass that may be wedged in the tread grooves
34. prior to enforcing state created rights or other rights which are independent of the Magnuson Moss Warranty Act or state replacement or repurchase laws IN CALIFORNIA U S ONLY California Civil Code Section 1793 2 d requires that if a manufacturer or its representative is unable to repair a motor vehicle to conform to the vehicle s applicable express warranty after a reasonable number of attempts the manufacturer shall be required to either replace the vehicle with one substantially identical or repurchase the vehicle and reimburse the buyer in an amount equal to the actual price paid or payable by the consumer less a reasonable allowance for consumer use The consumer has the right to choose whether to receive a refund or replacement vehicle California Civil Code Section 1793 22 b presumes that the manufacturer has had a reasonable number of attempts to conform the vehicle to its applicable express warranties if within the first 18 months of ownership of a new vehicle or the first 18 000 miles 29 000 km whichever occurs first 1 Two or more repair attempts are made on the same non conformity likely to cause death or serious bodily injury OR 2 Four or more repair attempts are made on the same nonconformity a defect or condition that substantially impairs the use value or safety of the vehicle OR 3 The vehicle is out of service for repair of nonconformities for a total of more than 30 calendar days not necessarily all at
35. refill of Traction Lok axles 3Ensure the correct automatic transmission fluid is used MERCON and MERCON V are not interchangeable DO NOT mix MERCON and MERCON V Refer toscheduled maintenance information to determine the correct service interval 4Approximate dry capacity includes cooler and tubes Fluid level should be checked by an authorized dealer Service refill capacity is covered under checking and adding manual transmission fluid in this chapter Use of synthetic or synthetic blend motor oil is not mandatory Engine oil need only meet the requirements of Ford specification WSS M2C929 A 4 0L or WSS M2C930 A 4 6L and the API Certification mark 231 Maintenance and Specifications LUBRICANT SPECIFICATIONS Item Ford part name Brake fluid and Motorcraft High clutch fluid if Performance equipped DOT 3 Motor Vehicle Brake Fluid Door Silicone weatherstrips Lubricant Door latch Multi Purpose hood latch Grease auxiliary hood latch striker plates seat tracks and fuel filler door hinge Engine coolant Motorcraft Premium Gold Engine Coolant yellow colored Engine oil 4 6L Motorcraft SAE engine 5W 20 Premium Synthetic Blend Motor Oil US Motorcraft SAE 5W 20 Super Premium Motor Oil Canada Engine oil 4 0L Motorcraft SAE V6 engine 5W 30 Premium Synthetic Blend Motor Oil US Motorcraft SAE 5W 30 Super Premium Motor Oil Canada Motorcraft Penetrating and
36. remove the chains to prevent damage to your vehicle If possible avoid fully loading your vehicle e Remove the tire chains when they are no longer needed Do not use tire chains on dry roads e The suspension insulation and bumpers will help prevent vehicle damage Do not remove these components from your vehicle when using snow tires and chains VEHICLE LOADING WITH AND WITHOUT A TRAILER This section will guide you in the proper loading of your vehicle and or trailer to keep your loaded vehicle weight within its design rating capability with or without a trailer Properly loading your vehicle will provide maximum return of vehicle design performance Before loading your vehicle familiarize yourself with the following terms for determining your vehicle s weight ratings with or without a trailer from the vehicle s Safety Compliance Certification Label 136 Tires Wheels and Loading Base Curb Weight is the weight of the vehicle including a full tank of fuel and all standard equipment It does not include passengers cargo or optional equipment Vehicle Curb Weight is the weight of your new vehicle when you picked it up from your authorized dealer plus any aftermarket equipment PAYLOAD Payload is the combined weight of cargo and passengers that the vehicle is carrying The maximum payload for your vehicle can be found on the Tire Label on the B Pillar or the edge of the drive
37. section in this chapter Use of a non approved automatic transmission fluid may cause internal transmission component damage and void the warranty Do not use supplemental transmission fluid additives treatments or cleaning agents The use of these materials may affect transmission operation and result in damage to internal transmission components 226 Maintenance and Specifications Checking and adding manual transmission fluid if equipped 1 Clean the filler plug 2 Remove the filler plug and inspect the fluid level 3 Note There are two different manual transmissions used in this vehicle and they have different fluid levels For vehicles equipped with a V6 engine the correct manual transmission fill level is at the lower edge of the filler hole For vehicles equipped with a V8 engine the correct manual transmission fill level is 1 2 inch 1 3 cm below the edge of the filler hole 227 Maintenance and Specifications e Fill level for V6 e Fill level for V8 4 Add enough fluid through the filler opening to bring the fluid up to the recommended levels 5 Install and tighten the fill plug securely Use only fluid that meets Ford specifications Refer to Lubricant specifications in this chapter MOTORCRAFT PART NUMBERS Component FA 1773 FA 1773 Electrical content 1The PCV valve is a critical emission component It is one of the items listed in scheduled maintenance information and is e
38. still present in the tank For consistent results when filling the fuel tank e Turn the engine ignition switch to the off position prior to refueling an error in the reading will result if the engine is left running 219 Maintenance and Specifications e Use the same filling rate setting dow medium high each time the tank is filled e Allow no more than two automatic click offs when filling e Always use fuel with the recommended octane rating e Use a known quality gasoline preferably a national brand e Use the same side of the same pump and have the vehicle facing the same direction each time you fill up e Have the vehicle loading and distribution the same every time Your results will be most accurate if your filling method is consistent Calculating fuel economy 1 Fill the fuel tank completely and record the initial odometer reading in miles or kilometers 2 Each time you fill the tank record the amount of fuel added Gn gallons or liters 3 After at least three to five tank fill ups fill the fuel tank and record the current odometer reading 4 Subtract your initial odometer reading from the current odometer reading 5 Follow one of the simple calculations in order to determine fuel economy Calculation 1 Divide total miles traveled by total gallons used Calculation 2 Multiply liters used by 100 then divide by total kilometers traveled Keep a record for at least one month and record
39. tether anchors 4 Access tether anchors located behind the seatback under the vinyl tag marked with the child tether anchor symbol 118 Seating and Safety Restraints A If the tether strap is clipped incorrectly the child safety seat may not be retained properly in the event of a collision 5 Clip the tether strap to the anchor as shown 6 Install the child safety seat tightly using the LATCH anchors or safety belts Follow the instructions in this chapter 7 Tighten the child safety seat tether strap according to the manufacturer s instructions If the safety seat is not anchored properly the risk of a child being injured in a collision greatly increases Attaching safety seats with LATCH Lower Anchors and Tethers for Children attachments Some child safety seats have two rigid or web mounted attachments that connect to two anchors at certain seating positions in your vehicle This type of child seat eliminates the need to use safety belts to attach the child seat For forward facing child seats the upper tether strap must also be attached to the proper tether anchor See Attaching safety seats with tether straps in this chapter 119 Seating and Safety Restraints Your vehicle has LATCH anchors for child seat installation at the seating positions marked with the child seat symbol The center of the rear seat is NOT designed as a seating position The LATCH anchors were not designed to be used
40. the United States this card is found in the Owner Guide portfolio in the glove compartment In Canada the card is found in the Owner Information Guide in the glove compartment U S Ford or Mercury vehicle customers who require roadside assistance call 1 800 241 3673 Lincoln vehicle customers call 1 800 521 4140 Canadian customers who require roadside assistance call 1 800 665 2006 If you need to arrange roadside assistance for yourself Ford Motor Company will reimburse a reasonable amount To obtain reimbursement information U S Ford or Mercury vehicles customers call 1 800 241 3673 Lincoln vehicle customers call 1 800 521 4140 Canadian customers who need to obtain reimbursement information call 1 800 665 2006 Roadside coverage beyond basic warranty In the United States you may purchase additional roadside assistance coverage beyond this period through the Ford Auto Club by contacting your authorized dealer Similarly in Canada for uninterrupted Roadside Assistance coverage you may purchase extended coverage prior to your Basic Warranty s Roadside Assistance expiring For more information and enrollment contact 1 877 294 2582 or visit our website at www ford ca HAZARD FLASHER CONTROL A The hazard flasher is located on the instrument panel by the radio The hazard flashers will operate when A the ignition is in any position or if the key is not in the ignition Push in the flasher control and al
41. the ignition to the 3 ON position with a coded key disarms the vehicle e The theft indicator will illuminate AN for three seconds and then go out n If the theft indicator stays on for an extended period of time or flashes rapidly have the system serviced by your authorized dealer Replacement keys If your keys are lost or stolen and you don t have an extra coded key you will need to have your vehicle towed to an authorized dealer The key codes need to be erased from your vehicle and new coded keys will need to be programmed Replacing coded keys can be very costly Store an extra programmed key away from the vehicle in a safe place to help prevent any inconveniences Please visit an authorized dealer to purchase additional spare or replacement keys Programming spare keys You can program your own coded keys to your vehicle Please read and understand the entire procedure before you begin 72 Locks and Security Tips e A maximum of eight keys can be coded to your vehicle e Only use Securilock keys e You must have two previously programmed coded keys keys that already operate your vehicle s engine and the new unprogrammed key s readily accessible e If no previously programmed coded keys are available you must take your vehicle to your authorized dealer to have the spare key s programmed 1 Insert a previously programmed coded key into the ignition 2 Turn the ignition from the 1
42. the radio Note The indicator lamp will illuminate for a short period of time when the ignition is turned to the ON position to confirm it is functional When the front passenger seat is not occupied empty seat or in the event that the front passenger frontal airbag is enabled may inflate the indicator lamp will be unlit 101 Seating and Safety Restraints The front passenger sensing system is designed to disable will not inflate the front passenger s frontal airbag when a rear facing infant seat a forward facing child restraint or a booster seat is detected e When the front passenger sensing system disables will not inflate the front passenger frontal airbag the indicator lamp will illuminate and stay lit to remind you that the front passenger frontal airbag is disabled e If the child restraint has been installed and the indicator lamp is not lit then turn the vehicle off remove the child restraint from the vehicle and reinstall the restraint following the child restraint manufacturer s instructions The front passenger sensing system is designed to enable may inflate the front passenger s frontal airbag anytime the system senses that a person of adult size is sitting properly in the front passenger seat e When the front passenger sensing system enables the front passenger frontal airbag may inflate the indicator will be unlit and stay unlit If a person of adult size is sitting in the front passenge
43. the type of driving city or highway This will provide an accurate estimate of the vehicle s fuel economy under current driving conditions Additionally keeping records during summer and winter will show how temperature impacts fuel economy In general lower temperatures give lower fuel economy Driving style good driving and fuel economy habits Give consideration to the lists that follow and you may be able to change a number of variables and improve your fuel economy Habits e Smooth moderate operation can yield up to 10 savings in fuel e Steady speeds without stopping will usually give the best fuel economy 220 Maintenance and Specifications Idling for long periods of time greater than one minute may waste fuel Anticipate stopping slowing down may eliminate the need to stop Sudden or hard accelerations may reduce fuel economy Slow down gradually Driving at reasonable speeds traveling at 55 mph 88 km h uses 15 less fuel than traveling at 65 mph 105 km h Revving the engine before turning it off may reduce fuel economy Using the air conditioner or defroster may reduce fuel economy You may want to turn off the speed control in hilly terrain if unnecessary shifting between third and fourth gear occurs Unnecessary shifting of this type could result in reduced fuel economy Warming up a vehicle on cold mornings is not required and may reduce fuel economy Resting your foot on the brake pedal whil
44. tires and wheels that were originally provided by Ford If the dissimilar spare tire or wheel is damaged it should be replaced rather than repaired A dissimilar spare tire wheel is defined as a spare tire and or wheel that is different in brand size or appearance from the road tires and wheels and can be one of three types 1 T type mini spare This spare tire begins with the letter T for tire size and may have Temporary Use Only molded in the sidewall 2 Full size dissimilar spare with label on wheel This spare tire has a label on the wheel that states THIS TIRE AND WHEEL FOR TEMPORARY USE ONLY When driving with one of the dissimilar spare tires listed above do not Exceed 50 mph 80 km h Load the vehicle beyond maximum vehicle load rating listed on the Safety Compliance Label 171 Roadside Emergencies Tow a trailer e Use snow chains on the end of the vehicle with the dissimilar spare tire Use more than one dissimilar spare tire at a time e Use commercial car washing equipment Try to repair the dissimilar spare tire Use of one of the dissimilar spare tires listed above at any one wheel location can lead to impairment of the following Handling stability and braking performance Comfort and noise Ground clearance and parking at curbs Winter weather driving capability Wet weather driving capability For vehicles equipped with 4WD it is not recommended that the veh
45. to scheduled maintenance information for the service interval schedules Keep the electrolyte level in each cell up to the level indicator Do not overfill the battery cells If the electrolyte level in the battery is low you can add plain tap water to the battery as long as you do not use hard water water with a high mineral or alkali content If possible however try to only fill the battery cells with distilled water If the battery needs water often have the charging system checked If your battery has a cover shield make sure it is reinstalled after the battery has been cleaned or replaced For longer trouble free operation keep the top of the battery clean and dry Also make certain the battery cables are always tightly fastened to the battery terminals If you see any corrosion on the battery or terminals remove the cables from the terminals and clean with a wire brush You can neutralize the acid with a solution of baking soda and water Batteries normally produce explosive gases which can cause personal injury Therefore do not allow flames sparks or lighted substances to come near the battery When working near the battery always shield your face and protect your eyes Always provide proper ventilation 206 Maintenance and Specifications When lifting a plastic cased battery excessive pressure on the end walls could cause acid to flow through the vent caps resulting in personal injury and or damage
46. with a child seat in the center position and there is no tether anchor available at the center Attempted use of the center as a seating position will increase the risk of injury or death in the event of a collision Never attach two LATCH child safety seats to the same anchor In a crash one anchor may not be strong enough to hold two child safety seat attachments and may break causing serious injury or death Locator symbols on the seat cushion indicate the seat has LATCH anchors The LATCH anchors are located behind the slits in the seat cushion Follow the child seat manufacturer s instructions to properly install a child seat with LATCH attachments Attach LATCH lower attachments of the child seat only to the anchors shown 120 Seating and Safety Restraints If you install a child seat with rigid LATCH attachments do not tighten the tether strap enough to lift the child seat off the vehicle seat cushion when the child is seated in it Keep the tether strap just snug without lifting the front of the child seat Keeping the child seat just touching the vehicle seat gives the best protection in a severe crash Each time you use the safety seat check that the seat is properly attached to the lower anchors and tether anchor Try to tilt the child seat from side to side Also try to tug the seat forward Check to see if the anchors hold the seat in place If the safety seat is not anchored prope
47. 1 OFF LOCK position To manually turn off the defroster before 10 minutes have passed push the control again Do not use razor blades or other sharp objects to clean the inside of the rear window or to remove decals from the inside of the rear window This may cause damage to the heated grid lines and will not be covered by your warranty CABIN AIR FILTER Your vehicle is equipped with a cabin air filter which is located just in front of the windshield under the cowl grille on the passenger side of the vehicle The particulate air filtration system is designed to reduce the concentration of airborne particles such as dust spores and pollen in the air being supplied to the interior of the vehicle The particulate filtration system gives the following benefits to customers e Improves the customer s driving comfort by reducing particle concentration e Improves the interior compartment cleanliness e Protects the climate control components from particle deposits For more information regarding the interval at which you should replace the cabin air filter refer to your scheduled maintenance information For additional cabin air filter information or to replace the filter see an authorized dealer 32 HEADLAMP CONTROL O O Turns the lamps off p Turns on the parking lamps instrument panel lamps license plate lamps and tail lamps ZD Turns the headlamps on High beams ZD Pull the lever towards you to the second d
48. 1 SUOTASE orrore aiora 171 Jump starting your vehicle 176 K Keyless entry system atole ei inaia 64 Keys positions of the ignition 146 L Lamps bulb replacement specifications chart 37 daytime running light 33 fog lamp Serer ra 34 headlarn pg ssies csedscareveavencsssssseess 33 Index headlamps flash to pass 33 instrument panel dimming 34 interior lamps sersisiiiessn 36 37 replacing bulbs 36 37 Lane change indicator see Turn signal 36 Lights warning and indicator 10 anti lock brakes ABS 151 Limited slip axle see Traction Loc ccce 154 Load VWitS oi kiss vessctesestessssestacises 136 Locks AUTOLOCK siisiveseiiaiicivesceoadivsinddaiaiy 64 Lubricant specifications 232 234 TS NULS yeon 176 Lumbar support seats 78 M Manual transmission 159 fluid capacities 0 0 0 0 230 lubricant specifications 234 TO VETS E ET eee 160 Message center cccccccceeseeeeeee 54 display Color ccceceeeeseeeeeee 55 english metric button 56 MyColor display ccceeeees 55 system check button 55 warning Messages ecce 60 MiTTOTS acs cceciesvasyetcedeaiscensscacnenvoen 47 side view mirrors power 47 Motorcraft parts 194 219 228 0 Octane Tating speriene 218 Oil see Engine oil 201 P Parking brake siscs
49. 17 mean the 31st week of 1997 After 2000 the numbers go to four digits For example 2501 means the 25th week of 2001 The numbers in between are identification codes used for traceability This information is used to contact customers if a tire defect requires a recall 9 M S or M S Mud and Snow or AT All Terrain or AS All Season 10 Tire Ply Composition and Material Used Indicates the number of plies or the number of layers of rubber coated fabric in the tire tread and sidewall Tire manufacturers also must indicate the ply materials in the tire and the sidewall which include steel nylon polyester and others 132 Tires Wheels and Loading 11 Maximum Load Indicates the maximum load in kilograms and pounds that can be carried by the tire Refer to the Safety Compliance Certification Label which is located on the B Pillar or the edge of the driver s door for the correct tire pressure for your vehicle 12 Treadwear Traction and Temperature Grades e Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course For example a tire graded 150 would wear one and one half 14 times as well on the government course as a tire graded 100 e Traction The traction grades from highest to lowest are AA A B and C The grades represent the tire s ability to stop on wet pavement as measured under controlled conditi
50. 6 km or more to relearn the idle and fuel trim strategy e If you do not allow the engine to relearn its idle trim the idle quality of your vehicle may be adversely affected until the idle trim is eventually relearned When the battery is disconnected or a new battery installed the transmission must relearn its adaptive strategy As a result of this the transmission may shift firmly This operation is considered normal and 207 Maintenance and Specifications will not affect function or durability of the transmission Over time the adaptive learning process will fully update transmission operation to its optimum shift feel If the battery has been disconnected or a new battery has been installed the clock and the preset radio stations must be reset once the battery is reconnected e Always dispose of automotive 2 batteries in a responsible manner s S Follow your local authorized Y G standards for disposal Call your t local authorized recycling center to find out more about recycling automotive batteries RECYCLE ENGINE COOLANT Checking engine coolant The concentration and level of engine coolant should be checked at the intervals listed in scheduled maintenance information The coolant concentration should be maintained at 50 50 coolant and distilled water which equates to a freeze point of 34 F 36 C Coolant concentration testing is possible with a hydrometer or antifreeze tester such as the Rotunda Battery
51. 9 Repeat Press to repeat the current CD track 10 Fast forward Press to manually advance in a CD track 11 Rewind Press to manually reverse in a CD track 12 Memory presets To set a station Select frequency band AM FM tune to a station press and hold a preset button until sound returns 13 Sean Press for a brief sampling of radio stations or CD tracks Press again to stop 14 Seek Press to access the next strong radio station or the previous track on the compact disc 15 AM FM Press to select AM FM frequency band 16 ON OFF Volume Press to turn ON OFF Turn to increase decrease volume If the volume is set above a certain level and the ignition is turned off the volume will come back on at a nominal listening level when the ignition switch is turned back on 17 CD Press to enter CD mode If a CD is already loaded into the system CD play will begin where it ended last ban VOL PUSH d 21 Entertainment Systems 18 CD eject Press to eject a CD 19 CD slot Insert a CD label side up SHAKER 500 Audiophile In Dash Six CD MP3 Sound System if equipped DaF 20 a B SHANER o CDOS MP3 l CD MUTE m FM AUX 45 VOL PUSH 14 SEEK SCAN SEEK 5 REW FF FOLDER FOLDER gt SHUFFLE TEXT 1 2 3 4 5 6 2 000000 22 Entertainment Systems SHAKER 1000 Audiophile In dash Six CD MP3 Sound System if equippe
52. Continued driving with this light on may cause the Service engine soon warning light to come on Refer to Fuel filler cap in the Maintenance and Specifications chapter Brake system warning light To confirm the brake system warning P light is functional it will ea illuminate when the B RAKE ignition is turned to the ON position when the engine is not running or in a position between ON and START or by applying the parking brake when the ignition is turned to the ON position If the brake system warning light does not illuminate at this time seek service immediately from your authorized dealer Illumination after releasing the parking brake indicates low brake fluid level and the brake system should be inspected immediately by your authorized dealer Check fuel cap if equipped wv Driving a vehicle with the brake system warning light on is dangerous A significant decrease in braking performance may occur It will take you longer to stop the vehicle Have the vehicle checked by your authorized dealer 11 Instrument Cluster Anti lock brake system if equipped If the ABS light stays illuminated or continues to flash a malfunction has been detected have the system serviced immediately by your authorized dealer Normal braking is still functional unless the brake warning light also is illuminated Airbag readiness If this light fails e to illuminate when ignition is turned to ON continues to flas
53. ENGER DOOR TRUNK BRAKE SYSTEM TRAC CONTROL if equipped FUEL CAP 9 FUEL LEVEL 10 MILES TO EMPTY Display color The instrument cluster gauges are backlit with white backlighting when the headlamps are off When the headlamps are on the user can select one of six preset colors or one user definable color MyColor for the nighttime gauge backlighting Headlamps must be on to set up the nighttime display color OANon fF WwW DH KF Note A gauge in a warning condition will be lit red when the headlamps are on 1 Press SETUP to get to the DISPLAY COLOR set up menu nisProayu COLOR TURN RERGLAMP ON 55 Driver Controls 2 Pressing RESET will scroll through the following selectable colors Green Blue Purple White Orange Red MyColor Adjust to define MyColor Adjusting MyColor MyColor is a user defined backlighting color The backlighting colors are achieved through the blending of light from Red Green and Blue LEDs Apart from the 6 preset colors drivers can create their own color by adjusting the levels of the three primary colors through the MyColor feature to achieve any of 125 different combinations The vehicle must be stationary to enter the MyColor adjust mode To enter the MyColor adjust mode hold RESET for 3 seconds at the Adjust menu or press SETUP to scroll though the display colors again When in the MyColor adjust mode pressing RESET will step through the Red Green
54. FORMATION RENSEIGNEMENTS RELATIFS AUX PNEUS ET A LA CHARGE CONSULTER LE GUIDE DU PROPRIETAIRE POUR DE PLUS AMPLES RESEIGNMENTS The combined weight of occupants and cargo should never exceed kgor PM bs b La charge du v hicle occupants et bagages ne doit jamais d passer kgou SEATING CAPACITY TOTAL TS FRONT Fg REAR RS NOMBRE DE PLACES TOTAL AVANT ARRIERE ORIGINAL TIRE SIZE COLD TIRE INFLATION PRESSURE DIMENSIONS DES PNEUS D ORIGINE PRESSION DE GONFLANGE A FROID FRONT AVANT FTIREXXXXXXE FRONT AVANT FKPA KPA FPS PSI REAR ARRIERE RTIREXXXXXXE RKPA KPA RPS PSI SPARE TIRE SIZE COLD TIRE INFLATION PRESSURE DIMENSION DU PNEU SECOURS PRESSION DE GONFLAGE A FROID STIREXXXXXXE SKP KPA SPS PSI XXX XX XXXX XXXX SXXXXXXXXXONINIAS CARGO Cargo Weight includes all weight added to the Base Curb Weight including cargo and optional equipment When towing trailer tongue load or king pin weight is also part of cargo weight 138 Tires Wheels and Loading GAW Gross Axle Weight is the total weight placed on each axle front and rear including vehicle curb weight and all payload GAWR Gross Axle Weight Rating is the maximum allowable weight that can be carried by a single axle front or rear These numbers are shown on the Safety Compliance Certification Label located on the B Pillar or the edge of the driver s door The total load on each axle must never exceed its GAWR Exceeding the Safety Com
55. GAGE located on the structure by the XX XXXKG XXXXLB iJj ivar E TIRE XXXX XXXXX XXX X XXXKG XXXXLB trailing edge of the driver s door or PRESSURE FE occ EA AKPS GOLD the edge of the driver s door PRESSURE RR XXX kPa XX PSI COLD TRAILER TOWING SEE OWNER GUIDE EXT PNT XXXXXX XXXXXX RC XX DSO XXXX F0000 BARTINTTR TP PS TR AXLE TTR SPR T0000 X XX XXX X XX X XXX UTC VFOHT 15294A10 GA 236 Maintenance and Specifications XXXXXXXXXXXXXXXXX Vehicle identification number VIN The vehicle identification number is attached to a metal tag and is located on the driver side instrument panel Please note that in the graphic XXXX is representative of your vehicle identification number The Vehicle Identification Number VIN contains the following information 1 World manufacturer identifier XXX X XXX X X X X XXXXXX 2 Brake type and Gross Vehicle Weight Rating GVWR 3 Vehicle line series body type oldlal 8 4 Engine type 5 Check digit 6 Model year 7 Assembly plant 8 Production sequence number 237 Maintenance and Specifications TRANSMISSION TRANSAXLE CODE DESIGNATIONS You can find a transmission transaxle code on the MFD BY FORD MOTOR CO IN U S A rm oti DATE XXIXX GVWR XXXXXLB XXXXXKG Safety Compliance Certification FRONT GAWR XXXXL REAR GAWR Label The following table tells you XXXXKG XXXXKG j os XXXX XXXXXXX XXXX XXXXXXX TIRES which transmi
56. Introduction Instrument Cluster Warning and control lights Gauges Entertainment Systems AM FM stereo with CD AM FM stereo with in dash six CD Climate Controls Manual heating and air conditioning Rear window defroster Lights Headlamps Turn signal control Bulb replacement Driver Controls Windshield wiper washer control Steering wheel adjustment Power windows Mirrors Speed control Message center Locks and Security Keys Locks Anti theft system Table of Contents 4 10 10 15 19 19 22 30 30 32 33 33 36 36 42 42 43 44 47 47 54 63 63 63 71 Table of Contents Seating and Safety Restraints Seating Safety restraints Airbags Child restraints Tires Wheels and Loading Tire Information Vehicle loading Trailer towing Recreational towing Driving Starting Brakes Traction control Transmission operation Roadside Emergencies Getting roadside assistance Hazard flasher switch Fuel pump shut off switch Fuses and relays Changing tires Lug Nut Torque Jump starting Wrecker towing Customer Assistance Reporting safety defects U S only Cleaning 76 76 82 97 107 122 122 136 142 145 146 146 150 152 154 162 162 163 164 164 171 176 176 181 182 188 189 Table of Contents Maintenance and Specifications 196 Engine compartment 198 Engine oil 201 Battery 206 Engine Coolant 208 Fuel information 214 Part
57. MATION Radio frequencies AM and FM frequencies are established by the Federal Communications Commission FCC and the Canadian Radio and Telecommunications Commission CRTC Those frequencies are AM 530 540 1600 1710 kHz FM 87 7 87 9 107 7 107 9 MHz Radio reception factors There are three factors that can affect radio reception e Distance strength The further you travel from a station the weaker the signal and the weaker the reception Terrain Hills mountains tall buildings power lines electric fences traffic lights and thunderstorms can interfere with your reception e Station overload When you pass a broadcast tower a stronger signal may overtake a weaker one and play while the weak station frequency is displayed CD player care Do e Handle discs by their edges only Never touch the playing surface e Inspect discs before playing Clean only with an approved CD cleaner and wipe from the center out Don t e Expose discs to direct sunlight or heat sources for extended periods of time e Insert more than one disc into each slot of the CD changer magazine e Clean using a circular motion 28 Entertainment Systems CD units are designed to play commercially pressed 4 75 in 12 cm audio compact discs only Due to technical incompatibility certain recordable and re recordable compact discs may not function correctly when used in Ford CD players Irregular shaped CDs CDs with a scratch protectio
58. Motorcraft Triple Clean U S only ZC 13 Motorcraft Ultra Clear Spray Glass Cleaner ZC 23 Motorcraft Vinyl Cleaner Canada only CXC 93 Motorcraft Vinyl Conditioner Canada only CXC 94 Motorcraft Wheel and Tire Cleaner ZC 37 A 195 Maintenance and Specifications SERVICE RECOMMENDATIONS To help you service your vehicle e We highlight do it yourself items in the engine compartment for easy location e We provide scheduled maintenance information which makes tracking routine service easy If your vehicle requires professional service your authorized dealer can provide the necessary parts and service Check your Warranty Guide Owner Information Guide to find out which parts and services are covered Use only recommended fuels lubricants fluids and service parts conforming to specifications Motorcraft parts are designed and built to provide the best performance in your vehicle PRECAUTIONS WHEN SERVICING YOUR VEHICLE e Do not work on a hot engine e Make sure that nothing gets caught in moving parts e Do not work on a vehicle with the engine running in an enclosed space unless you are sure you have enough ventilation e Keep all open flames and other burning cigarettes material away from the battery and all fuel related parts Working with the engine off e Automatic transmission 1 Set the parking brake and shift to P Park 2 Turn off the engine and remove the key 3 Block the wheels e Ma
59. Note Large metallic objects electronic devices that are used to purchase gasoline or similar items or a second coded key on the same key chain may cause vehicle starting issues You need to prevent these objects from touching the coded key while starting the engine These objects will not cause damage to the coded key but may cause a momentary issue if they are too close to the key when starting the engine If a problem occurs turn the ignition off remove all objects on the key chain away from the coded key and restart the engine Anti theft indicator The anti theft indicator is located in AN the instrument cluster f R e When the ignition is in the 1 OFF LOCK position the indicator will flash once every 2 seconds to indicate the SecuriLock system is functioning as a theft deterrent e When the ignition is in the 3 ON position the indicator will glow for 3 seconds then turn off to indicate normal system functionality If a problem occurs with the SecuriLock system the indicator will flash rapidly or glow steadily when the ignition is in the 3 ON position If this occurs the vehicle should be taken to an authorized dealer for service 71 Locks and Security Automatic arming The vehicle is armed immediately after switching the ignition to the 1 OFF LOCK position The theft indicator will flash every A two seconds when the vehicle is f R armed Automatic disarming Switching
60. Ordering additional owner s TQTATULE 2 cf shssesssasersiatecassvaeeees 187 Utilizing the Mediation Arbitration PRO STAN ees 185 D Daytime running lamps see Lamps cccceceseseeeesteeeee 33 Dipstick automatic transmission PUI RE ONEA EE T 226 ENGINE Oil isiriina enin 201 242 Doors lubricant specifications 232 Driving under special COMGIGIONS eseina oe ake 158 through water 161 E Electronic message center 54 Emergencies roadside jJump starting oe 176 Emission control system 222 ENSING serapan 234 CLEANING isccsseccsiestssanaveganheeievers 190 COOLANT fcc ssscssauestevs steseeattetessceaes 208 fail safe cooling o oo 213 idle speed control 000 206 lubrication specifications 0 00 232 234 refill capacities cccccceeees 230 service points seese 198 199 Engine block heater 0 0 0 0 150 ENSING COI secssescaedecrsneeeatetses 201 checking and adding 201 CIDSTUCK sists tote Gou cess Sones aks 201 filter specifications 204 228 recommendations cccce 204 refill capacities eee 230 specifications 0 232 234 Exhaust fumes cccceeeees 149 F Fail safe cooling eee 213 Ploor Mats ooo eee eceeseseeeeeseeeeeee 62 Fluid capacities 2 0 0 230 POSlAMDS sirier uate 34 FUE ennio 214 calculating fuel ECONOMY siii inean 58 219 Ere O A A 216 Capacily sciscsiseecetnasmesesteruc
61. R limitations Replacement tires with a higher limit than the originals do not increase the GVWR and GAWR limitations Exceeding any vehicle weight rating limitation could result in serious damage to the vehicle and or personal injury Steps for determining the correct load limit 1 Locate the statement The combined weight of occupants and cargo should never exceed XXX kg or XXX Ibs on your vehicle s placard 2 Determine the combined weight of the driver and passengers that will be riding in your vehicle 3 Subtract the combined weight of the driver and passengers from XXX kg or XXX lbs 4 The resulting figure equals the available amount of cargo and luggage load capacity For example if the XXX amount equals 1 400 Ibs and there will be five 150 lb passengers in your vehicle the amount of available cargo and luggage load capacity is 650 Ibs 1400 750 5 x 150 650 lb In metric units 635 340 5 x 68 295 kg 5 Determine the combined weight of luggage and cargo being loaded on the vehicle That weight may not safely exceed the available cargo and luggage load capacity calculated in Step 4 6 If your vehicle will be towing a trailer load from your trailer will be transferred to your vehicle Consult this manual to determine how this reduces the available cargo and luggage load capacity of your vehicle 141 Tires Wheels and Loading The following gives you a few examples on how to calculate the avai
62. Take care when using a power washer to clean the engine The high pressure fluid could penetrate the sealed parts and cause damage e Do not spray a hot engine with cold water to avoid cracking the engine block or other engine components e Spray Motorcraft Engine Shampoo and Degreaser ZC 20 on all parts that require cleaning and pressure rinse clean e Cover the highlighted areas to prevent water damage when cleaning the engine 190 Cleaning TN N N TA X NN Ye See au Ewin root A e 4 0L SOHC V6 engine S R N dr 1 D AY K YA Q LS K tte xt A M 7 Lr P n H D eS Q ee KS ax D e 4 6L 3V SOHC V8 engine e Never wash or rinse the engine while it is running water in the running engine may cause internal damage 191 Cleaning PLASTIC NON PAINTED EXTERIOR PARTS Use only approved products to clean plastic parts These products are available from your authorized dealer e For routine cleaning use Motorcraft Detail Wash ZC 3 A e If tar or grease spots are present use Motorcraft Bug and Tar Remover ZC 42 e For plastic headlamp lenses use Motorcraft Ultra Clear Spray Glass Cleaner ZC 23 WINDOWS AND WIPER BLADES The windshield rear and side windows and the wiper blades should be cleaned regularly If the wipers do not wipe pr
63. Tires can be damaged during off road use so inspection after off road use is also recommended Age Tires degrade over time even when they are not being used It is recommended that tires generally be replaced after 6 years of normal service Heat caused by hot climates or frequent high loading conditions can accelerate the aging process You should replace the spare tire when you replace the other road tires due to the aging of the spare tire U S DOT Tire Identification Number TIN Both U S and Canada Federal regulations require tire manufacturers to place standardized information on the sidewall of all tires This information identifies and describes the fundamental characteristics of the tire and also provides a U S DOT Tire Identification Number for safety standard certification and in case of a recall 127 Tires Wheels and Loading This begins with the letters DOT and indicates that the tire meets all federal standards The next two numbers or letters are the plant code designating where it was manufactured the next two are the tire size code and the last four numbers represent the week and year the tire was built For example the numbers 317 mean the 31st week of 1997 After 2000 the numbers go to four digits For example 2501 means the 25th week of 2001 The numbers in between are identification codes used for traceability This information is used to contact customers if a tire defect requires a recall Tire Rep
64. abilities and its inflation limits 3 Maximum Load Dual Ib kg at psi kPa cold Indicates the maximum load and tire pressure when the tire is used as a dual defined as four tires on the rear axle a total of six or more tires on the vehicle 4 Maximum Load Single lb kg at psi kPa cold Indicates the maximum load and tire pressure when the tire is used as a single defined as two tires total on the rear axle 134 Tires Wheels and Loading Information on T type tires T type tires have some additional information beyond those of P type tires these differences are described below T145 80D16 is an example of a tire size Note The temporary tire size for your vehicle may be different from this example 1 T Indicates a type of tire designated by the Tire and Rim Association T amp RA that is intended for temporary service on cars SUVs minivans and light trucks 2 145 Indicates the nominal width of the tire in millimeters from sidewall edge to sidewall edge In general the larger the number the wider the tire Ay 30 a1 NG J 3 80 Indicates the aspect ratio which gives the tire s ratio of height to width Numbers of 70 or lower indicate a short sidewall 4 D Indicates a diagonal type tire R Indicates a radial type tire 5 16 Indicates the wheel or rim diameter in inches If you change your wheel size you will have to purchase new tires to
65. access the information independently of Ford Motor Company and Ford of Canada Cell phone use The use of Mobile Communications Equipment has become increasingly important in the conduct of business and personal affairs However drivers must not compromise their own or others safety when using such equipment Mobile Communications can enhance personal safety and security when appropriately used particularly in emergency situations Safety must be paramount when using mobile communications equipment to avoid negating these benefits Mobile Communication Equipment includes but is not limited to cellular phones pagers portable email devices in vehicle communications systems telematics devices and portable two way radios A driver s first responsibility is the safe operation of the vehicle The most important thing you can do to prevent a crash is to avoid distractions and pay attention to the road Wait until it is safe to operate Mobile Communications Equipment Middle East North Africa vehicle specific information For your particular global region your vehicle may be equipped with features and options that are different from the ones that are described in this Owner s Guide therefore a supplement has been supplied that complements this book By referring to the pages in the provided supplement you can properly identify those features recommendations and specifications that are unique to your vehicle Refer to this Owner
66. acing child seats or infant carriers should never be placed in front of an active airbag Installing child safety seats with combination lap and shoulder belts Air bags can kill or injure a child in a child seat NEVER place a rear facing child seat in front of an active air bag If you must use a forward facing child seat in the front seat move the seat all the way back 1 Position the child safety seat in a seat with a combination lap and shoulder belt Children 12 and under should be properly restrained in the rear seat whenever possible 113 Seating and Safety Restraints 2 Pull down on the shoulder belt and then grasp the shoulder belt and lap belt together 3 While holding the shoulder and lap belt portions together route the tongue through the child seat according to the child seat manufacturer s instructions Be sure the belt webbing is not twisted 4 Insert the belt tongue into the proper buckle the buckle closest to the direction the tongue is coming from for that seating position until you hear a snap and feel the latch engage Make sure the tongue is latched securely by pulling on it 114 Seating and Safety Restraints 5 To put the retractor in the automatic locking mode grasp the xX shoulder portion of the belt and pull N downward until all of the belt is A extracted and a click is heard 6 Allow the belt to retract The belt will click as it retracts to indicate it is in the auto
67. amage to the vehicle loss of control and personal injury GCW Gross Combined Weight is the weight of the loaded vehicle GVW plus the weight of the fully loaded trailer GCWR Gross Combined Weight Rating is the maximum allowable weight of the vehicle and the loaded trailer including all cargo and passengers that the vehicle can handle without risking damage Important The towing vehicles braking system is rated for operation at GVWR not at GCWR Separate functional brakes should be used for safe control of towed vehicles and for trailers where the GCW of the towing vehicle plus the trailer exceed the GVWR of the towing vehicle The GCW must never exceed the GCWR 140 Tires Wheels and Loading Maximum Loaded Trailer Weight is the highest possible weight of a fully loaded trailer the vehicle can tow It assumes a vehicle with only mandatory options no cargo internal or external a tongue load of 10 15 conventional trailer or king pin weight of 15 25 fifth wheel trailer and driver only 150 lb 68 kg Consult your authorized dealer or the RV and Trailer Towing Guide provided by your authorized dealer for more detailed information Do not exceed the GVWR or the GAWR specified on the Safety Compliance Certification Label Do not use replacement tires with lower load carrying capacities than the originals because they may lower the vehicle s GVWR and GAW
68. amperage rating and color Standard Sage Fuse link maxi f uses Ta cartridge 15A Blue Bue gt q Passenger compartment fuse panel The fuse panel is located in the lower passenger side area behind the kick panel Remove the trim panel cover and the fuse cover to access the fuses To remove a fuse use the fuse puller tool provided on the fuse panel cover 165 Roadside Emergencies The fuses are coded as follows Fuse Relay Fuse Amp Passenger Compartment Fuse 1 Noted o PAT 5A Power mirrors O O PT Noted S O PA Accessory delay feeds 10A Cluster Data Link Connector DLC Ooo Notused i y O Climate control E Ooo o n Not sed S e 166 Roadside Emergencies Fuse Relay Fuse Amp Passenger Compartment Fuse Location Rating Panel Description 17 10A Restraint Control Module RCM Passenger Occupant Detection System PODS Passenger Air bag Deactivation Indicator PADI 18 10A Anti lock Brake System ABS Positive Crankcase Ventilation PCV valve heater Ignition 19 5A Powertrain Control Module PCM relays Passive Anti Theft System PATS Power distribution box The power distribution box is located in the engine compartment The power distribution box contains high current fuses that protect your vehicle
69. as the safety belt Manufacturer identification is located at the end of the webbing on the label Also use the safety belt extension only if the safety belt is too short for you when fully extended Do not use extensions to change the fit of the shoulder belt across the torso Safety belt maintenance Inspect the safety belt systems periodically to make sure they work properly and are not damaged Inspect the safety belts to make sure there are no nicks tears or cuts Replace if necessary All safety belt assemblies including retractors buckles front safety belt buckle assemblies buckle support assemblies slide bar if equipped shoulder belt height adjusters Gf equipped shoulder belt guide on seatback if equipped child safety seat LATCH and tether anchors and attaching hardware should be inspected after a collision Ford Motor Company recommends that all safety belt assemblies in use in vehicles involved in a collision be replaced However if the collision was minor and an authorized dealer finds that the belts do not show damage and continue to operate properly they do not need to be replaced Safety belt assemblies not in use during a collision should also be inspected and replaced if either damage or improper operation is noted Failure to inspect and if necessary replace the safety belt assembly under the above conditions could result in severe personal injuries in the event of a collision For proper care of soiled safet
70. at or cargo interfering with the seat e Remove the obstruction s Gf found e Restart the vehicle 104 Seating and Safety Restraints e Wait at least 2 minutes and verify that the airbag readiness light is no longer illuminated e If the airbag readiness lamp remains illuminated this may or may not be a problem due to the front passenger sensing system DO NOT attempt to repair or service the system take your vehicle immediately to an authorized dealer If it is necessary to modify an advanced front airbag system to accommodate a person with disabilities contact the Ford Customer Relationship Center at the phone number shown in the Customer Assistance section of this Owner s Guide Any alteration modification to the front passenger seat may affect the performance of the front passenger sensing system Seat mounted side airbag system if equipped 4o Do not place objects or mount equipment on or near the airbag cover on the side of the seatbacks of the front seats or in front seat areas that may come into contact with a deploying airbag Failure to follow these instructions may increase the risk of personal injury in the event of a collision Do not use accessory seat covers The use of accessory seat covers may prevent the deployment of the side airbags and increase the risk of injury in an accident Do not lean your head on the door The side airbag could injure you as it deploys from the side of the seatback Do no
71. at this procedure from Step 1 for each additional key ACTIVE ANTI THEFT SYSTEM IF EQUIPPED The active anti theft system is designed to warn you in the event of an unauthorized entry to your vehicle and is also designed to help prevent the unwanted towing of the vehicle When the vehicle is locked and armed the active anti theft system monitors the following e Doors e Hood e Trunk e Movement inside the vehicle e Change in vehicle inclination Note The active anti theft system includes a motion detection system which monitors the passenger cabin and a vehicle incline sensor which detects changes in vehicle attitude The interior motion detection and vehicle incline sensing systems will operate only when the vehicle is locked using the remote keyless entry transmitter or when using the power door lock control with the accompanying door open and all doors then become closed For convertible vehicles the convertible top must be in the fully closed and latched position for the interior motion sensing system to arm If you lock the vehicle using the key in the driver door key cylinder the system will monitor the doors trunk and hood but the motion sensing and vehicle incline sensing will not arm Do not arm the interior motion detection system if movement within the vehicle is likely to occur Additionally do not arm the vehicle incline sensing system when the vehicle is in transport For proper operation of the interior motion
72. ater to bring the liquid level to the proper level If you have to add more than 1 0 quart 1 0 liter of engine coolant per month have your authorized dealer check the engine cooling system Your cooling system may have a leak Operating an engine with a low level of coolant can result in engine overheating and possible engine damage Recycled engine coolant Ford Motor Company does NOT recommend the use of recycled engine coolant in vehicles originally equipped with Motorcraft Premium Gold Engine Coolant since a Ford approved recycling process is not yet available 211 Maintenance and Specifications Used engine coolant should be disposed of in an appropriate manner Follow your community s regulations and standards for recycling and disposing of automotive fluids Coolant refill capacity To find out how much fluid your vehicle s cooling system can hold refer to Refill capacities in this section Fill your engine coolant reservoir as outlined in Adding engine coolant in this section Severe climates If you drive in extremely cold climates less than 34 F 36 C J e It may be necessary to increase the coolant concentration above 50 e NEVER increase the coolant concentration above 60 e Increased engine coolant concentrations above 60 will decrease the overheat protection characteristics of the engine coolant and may cause engine damage e Refer to the chart on the coolant container to ensure the coolant con
73. ation move control up one A position Adjust the rotary control to the desired speed setting For normal or low speed wiper operation move control up two positions from OFF For high speed wiper operation move control up three positions from OFF Windshield washer Pull the end of the stalk towards you e briefly causes a single swipe of the wipers without washer fluid e a quick pull and hold the wipers N will swipe three times with v4 washer fluid e along pull and hold the wipers and washer fluid will be activated for up to ten seconds 42 Driver Controls TILT STEERING WHEEL IF EQUIPPED To adjust the steering wheel 1 Push the lever down to unlock the steering column While the lever is in the down position tilt the steering column to its desired orientation 2 While holding the steering column pull the lever up to its original position to lock the steering column Never adjust the steering wheel when the vehicle is moving AUXILIARY POWER POINT 12VDC Power outlets are designed for accessory plugs only Do not insert any other object in the power outlet as this will damage the outlet and blow the fuse Do not hang any type of accessory or accessory bracket from the plug Improper use of the power outlet can cause damage not covered by your warranty The power point is an additional power source for electrical accessories The power points are located on the instrument pa
74. ature for objects placed in the front passenger seat warnings will only be given to large front seat occupants as determined by the front passenger sensing system Both the driver s and passenger s safety belt usages are monitored and either may activate the BeltMinder feature The warnings are the same for the driver and the front passenger If the BeltMinder warnings have expired warnings for approximately 5 minutes for one occupant driver or front passenger the other occupant can still activate the BeltMinder feature 92 Seating and Safety Restraints The driver s and front The BeltMinder feature will not passenger s safety belts are activate buckled before the ignition switch is turned to the ON position or less than 1 2 minutes have elapsed since the ignition switch has been turned ON The driver s or front The BeltMinder feature is activated passenger s safety belt is not the safety belt warning light buckled when the vehicle has illuminates and the warning chime reached at least 3 mph 5 sounds for 6 seconds every 30 km h and 1 2 minutes have seconds repeating for approximately elapsed since the ignition 5 minutes or until the safety belts are switch has been turned to buckled ON The driver s or front The BeltMinder feature is activated passenger s safety belt becomes the safety belt warning light unbuckled for approximately 1 illuminates and the warning chime minute while
75. authorized dealer in properly servicing your vehicle When the C indicator illuminates the OBD II system has detected a malfunction Temporary malfunctions may cause your ia indicator to illuminate Examples are 1 The vehicle has run out of fuel the engine may misfire or run poorly 2 Poor fuel quality or water in the fuel 3 The fuel cap may not have been securely tightened See Fuel filler cap in this chapter 223 Maintenance and Specifications These temporary malfunctions can be corrected by filling the fuel tank with good quality fuel and or properly tightening the fuel cap After three driving cycles without these or any other temporary malfunctions present the C indicator should turn off A driving cycle consists of a cold engine startup followed by mixed city highway driving No additional vehicle service is required If the indicator remains on have your vehicle serviced at the first available opportunity Readiness for Inspection Maintenance I M testing In some localities it may be a legal requirement to pass an I M test of the on board diagnostics system If your indicator is on refer to the description in the Warning lights and chimes section of the Instrument Cluster chapter Your vehicle may not pass the I M test with the indicator on If the vehicle s powertrain system or its battery has just been serviced the on board diagnostics system is reset to a not ready for I M test condition
76. ay find this information in your Owner s Guide If not contact a local tire dealer Note You may not find this information on all tires because it is not required by federal law 7 H Indicates the tire s speed rating The speed rating denotes the speed at which a tire is designed to be driven for extended periods of time under a standard condition of load and inflation pressure The tires on your vehicle may operate at different conditions for load and inflation pressure These speed ratings may need to be adjusted for the difference in conditions The ratings range from 81 mph 130 km h to 186 mph 299 km h These ratings are listed in the following chart 131 Tires Wheels and Loading Note You may not find this information on all tires because it is not required by federal law po QT 99 mph I rH O PR 106 mph GT rh O Note For tires with a maximum speed capability over 149 mph 240 km h tire manufacturers sometimes use the letters ZR For those with a maximum speed capability over 186 mph 299 km h tire manufacturers always use the letters ZR 8 U S DOT Tire Identification Number TIN This begins with the letters DOT and indicates that the tire meets all federal standards The next two numbers or letters are the plant code designating where it was manufactured the next two are the tire size code and the last four numbers represent the week and year the tire was built For example the numbers 3
77. both engines or any fuel delivery system parts Jump starting 1 Start the engine of the booster vehicle and run the engine at moderately increased speed 178 Roadside Emergencies 2 Start the engine of the disabled vehicle 3 Once the disabled vehicle has been started run both engines for an additional three minutes before disconnecting the jumper cables Removing the jumper cables Remove the jumper cables in the reverse order that they were connected 1 Remove the jumper cable from the ground metal surface Note In the illustrations lightning bolts are used to designate the assisting boosting battery 2 Remove the jumper cable on the negative connection of the booster vehicle s battery 179 Roadside Emergencies 3 Remove the jumper cable from the positive terminal of the booster vehicle s battery 4 Remove the jumper cable from the positive terminal of the disabled vehicle s battery After the disabled vehicle has been started and the jumper cables removed allow it to idle for several minutes so the engine computer can relearn its idle conditions 180 Roadside Emergencies WRECKER TOWING If you need to have your vehicle towed contact a professional towing service or if you are a member of a roadside assistance program your roadside assistance service provider It is recommended that your vehicle be towed wit
78. centration in your vehicle will provide adequate freeze protection at the temperatures in which you drive in the winter months If you drive in extremely hot climates e It is still necessary to maintain the coolant concentration above 40 e NEVER decrease the coolant concentration below 40 e Decreased engine coolant concentrations below 40 will decrease the corrosion protection characteristics of the engine coolant and may cause engine damage e Decreased engine coolant concentrations below 40 will decrease the freeze protection characteristics of the engine coolant and may cause engine damage e Refer to the chart on the coolant container to ensure the coolant concentration in your vehicle will provide adequate protection at the temperatures in which you drive Vehicles driven year round in non extreme climates should use a 50 50 mixture of engine coolant and distilled water for optimum cooling system and engine protection 212 Maintenance and Specifications cant you should know about fail safe cooling 4 6L V8 engine only If the engine coolant supply is depleted this feature allows the vehicle to be driven temporarily before incremental component damage is incurred The fail safe distance depends on ambient temperatures vehicle load and terrain How fail safe cooling works If the engine begins to overheat e The engine coolant temperature gauge will move to the red hot area e The engine coolant te
79. d 20 CD MUTE m FM AUX 45 VOL PUSH 44 SEEK SCAN SEEK 5 REW FF FOLDER FOLDER SHUFFLE TEXT 2 3 4 5 6 Ome er arcana Accessory delay Your vehicle is equipped with accessory delay With this feature the window switches and radio may be used for up to ten minutes after the ignition switch is turned to the OFF position or until any door or trunk is opened Your vehicle may be equipped with the SHAKER 1000 audio system This system is equipped with a rack of amplifiers and subwoofers in the trunk of the vehicle The SHAKER 1000 audio system is capable of producing very high sound pressure levels For your listening comfort and protection it is not recommended to listen to the SHAKER 1000 audio system at high volume levels for extended periods of time 1 A v Tune Disc selector Press to manually go up or down the radio frequency or to select a desired disc Also use in menu mode to select various settings 2 Phone mute Press to mute the playing media Press again to return to the playing media 23 Entertainment Systems 3 Menu Press to toggle through the following modes Setting the clock Press until SELECT HOUR or SELECT MINS is displayed Press A IV 4 SEEK gt to adjust the hours minutes SHAKER Available with the SHAKER 1000 only Select to engage SHAKER 1000 mode SHAKER 1000 mode enhances acoustic sound for all seat
80. d refill capacities 230 lubricant specifications 232 234 manual operation 0 159 TUNK sinari ena 65 remote TElLEASE ci vsvessecdersedacciers 68 Turn SIGNAL srneci 36 Vv Vehicle dimensions 00008 235 Vehicle Identification Number OVIN serani ennen 237 Vehicle loading eeeee 136 Ventilating your vehicle 150 WwW Warning lights see Lights 10 Washer fluid cies sevccccessvesetsdasseeacs 200 Water Driving through 161 Windows DOWER eropa 44 Windshield washer fluid and OPCTAULION rennin knn wipers replacing wiper blades 201 checking and adding fluid 200 Wrecker towing csccseeseeseeeee 181 246 247 248
81. d and locked 2 Press and release again within three seconds to confirm that all the doors are closed and locked Note The doors will lock again the horn will chirp once and the turn signal lamps will flash once more If any of the doors trunk or hood if equipped with active anti theft system are not properly closed the horn will make two quick chirps and the turn signal lamps will not flash If the vehicle is not equipped with the active anti theft system the horn will make two quick chirps and the turn signal lamps will not flash if the doors and the trunk are not closed and locked Opening the trunk Press once to open the trunk e Ensure that the trunk is closed and latched before driving your vehicle Failure to properly latch the trunk may cause objects to fall out or block the driver s rear view The remote entry system allows you to open the trunk while the ignition is in any position However if the ignition is in the 3 ON position and the vehicle is in motion the trunk will not open if the vehicle is moving 3 mph 5 km h or faster Sounding a panic alarm Press to activate the alarm The horn will sound and the turn signal and interior lamps will flash for a maximum of approximately 3 minutes Press again or turn the ignition to the 2 ACCESSORY or 3 ON position to deactivate or wait for the alarm to timeout in 3 minutes Note The panic alarm will only operate when the ignition is in the 1 OFF LOCK po
82. dardized information on the sidewall of all tires This information identifies and describes the fundamental characteristics of the tire and also provides a U S DOT Tire Identification Number for safety standard certification and in case of a recall 130 Tires Wheels and Loading Information on P type tires P215 65R15 95H is an example of a tire size load index and speed rating The definitions of these items are listed below Note that the tire size load index and speed rating for your vehicle may be different from this example 1 P Indicates a tire designated by the Tire and Rim Association T amp RA that may be used for service on cars SUVs minivans and light trucks Note If your tire size does not begin with a letter this may mean it is designated by either ETRTO European Tire and Rim Technical Organization or JATMA Japan Tire Manufacturing Association 2 215 Indicates the nominal width of the tire in millimeters from sidewall edge to sidewall edge In general the larger the number the wider the tire 3 65 Indicates the aspect ratio which gives the tire s ratio of height to width 4 R Indicates a radial type tire 5 15 Indicates the wheel or rim diameter in inches If you change your wheel size you will have to purchase new tires to match the new wheel diameter 6 95 Indicates the tire s load index It is an index that relates to how much weight a tire can carry You m
83. der the vehicle while changing a tire Do not start the engine when your vehicle is on the jack The jack is only meant for changing the tire 5 Remove the lug nuts with the lug wrench 6 Replace the flat tire with the spare tire making sure the valve stem is facing outward Reinstall lug nuts until the wheel is snug against the hub Do not fully tighten the lug nuts until the wheel has been lowered If you are using the temporary tire the lug nut washers will not appear to be flush with the rim This is normal only when using the temporary spare tire 7 Lower the wheel by turning the jack handle counterclockwise 8 Remove the jack and fully tighten the lug nuts in the order shown Refer to Wheel lug nut torque specifications later in this chapter for the proper lug nut torque specification 9 Put flat tire wheel ornament if equipped jack and lug wrench away Make sure jack is fastened so it does not rattle when you drive 10 Unblock the wheels 175 Roadside Emergencies WHEEL LUG NUT TORQUE SPECIFICATIONS Retighten the lug nuts to the specified torque at 500 miles 800 km after any wheel disturbance tire rotation changing a flat tire wheel removal etc Bolt size Wheel lug nut torque Ib ft Torque specifications are for nut and bolt threads free of dirt and rust Use only Ford recommended replacement fasteners When a wheel is installed always remove any corrosion dirt or foreign materials
84. detection system ensure all windows are closed prior to arming the system This will help prevent accidental alarm activation due to external influences and ensure proper interior motion detection Additionally the interior motion sensing system will not arm if either door or the trunk is ajar If there is any potential active anti theft problem with your vehicle ensure ALL remote entry transmitters are taken to an authorized dealer to aid in troubleshooting 74 Locks and Security Arming the system When armed the active anti theft system is designed to notify you of an unauthorized entry When unauthorized entry or towing occurs the system will flash the turn signal lamps and interior lamps and sounds the security horn The system is ready to arm whenever the key is out of the ignition Any of the following actions will arm the alarm system e Press the remote transmitter lock control one time to arm the system e Lock all doors using the interior power lock switch while the driver or passenger door is open and then becomes closed e Lock the driver door with the key in the key lock cylinder this will not however arm the interior motion or vehicle incline sensing systems or lock the passenger door If all the closures doors trunk hood are closed the turn signal lamps will flash once If any closure is not properly closed the parklamps will not flash Note Locking the driver door with the key does not lock the passenge
85. dio volume changes automatically and slightly with vehicle speed to compensate for road and wind noise Recommended level is 1 3 Level 0 turns the feature off and level 7 is the maximum setting Press MENU to access and use A IV 4 SEEK p gt to adjust the volume setting The level will appear in the display Setting the clock Press MENU until SELECT HOUR or SELECT MINUTE is displayed Use A IV to manually increase decrease Press MENU again to disengage clock mode Autoset Allows you to set the strongest local radio stations without losing your original manually set preset stations for AM FM1 FM2 Press MENU to access Use A IV 4 SEEK p gt to set or turn on off When the six strongest stations are filled the station stored in preset 1 will begin playing If there are less than six strong stations the system will store the last one in the remaining presets You can then access the stations by pressing the memory presets To disengage press MENU to access and press A IV la SEEK P to turn the feature off 4 Aux If no auxiliary sources are available NO AUX AUDIO will be oA displayed 5 Seek Press to access the next strong radio station or the next track on the compact disc 6 Text This control is not operational 7 Shuffle Press to play tracks in random order 20 Entertainment Systems 8 Comp Compression In CD mode brings soft and loud CD passages together for a more consistent listening level
86. disabled they can only become active when a valid electronic unlock event i e using the remote entry transmitter occurs Deactivating activating the power door trim switch inhibit feature Before following the procedure make sure that the ignition is in the 1 OFF LOCK position and all vehicle doors are closed You must complete Steps 1 7 within 30 seconds or the procedure will have to be repeated If the procedure needs to be repeated you must wait 30 seconds 1 Turn the ignition to the 3 ON position 2 Press the power door unlock control three times 3 Turn the ignition from the 3 ON to the 1 OFF LOCK position 4 Press the power door unlock control three times 5 Turn the ignition back to the 3 ON position The horn will chirp 6 Press the lock control two times The horn will chirp once if power door trim switch inhibit was deactivated or twice one short and one long chirp if the feature was activated 7 Turn the ignition to the 1 OFF LOCK position The horn will chirp once to confirm the procedure is complete INTERIOR LUGGAGE COMPARTMENT RELEASE Your vehicle is equipped with a mechanical interior luggage compartment release handle that provides a means of escape for children and adults in the event they become locked inside the luggage compartment Adults are advised to familiarize themselves with the operation and location of the release handle 65 Locks and Security To open the luggage compar
87. driving needs Ford ESP also offers reimbursement benefits for towing and rental coverage When you buy Ford ESP you receive Peace of Mind protection throughout the United States and Canada provided by a network of more than 4 600 participating authorized dealers If you did not take advantage of the Ford Extended Service Plan at the time of purchasing your vehicle you may still be eligible Since this information is subject to change please ask your authorized dealer for complete details about Ford Extended Service Plan coverage options or visit the Ford ESP website at www ford esp com GETTING ASSISTANCE OUTSIDE THE U S AND CANADA Before exporting your vehicle to a foreign country contact the appropriate foreign embassy or consulate These officials can inform you of local vehicle registration regulations and where to find unleaded fuel 186 Customer Assistance If you cannot find unleaded fuel or can only get fuel with an anti knock index lower than is recommended for your vehicle contact a regional office or owner relations customer relationship office The use of leaded fuel in your vehicle without proper conversion may damage the effectiveness of your emission control system and may cause engine knocking or serious engine damage Ford Motor Company Ford of Canada is not responsible for any damage caused by use of improper fuel Using leaded fuel may also result in difficulty importing your vehicle back into the U S If
88. ducts available to clean your vehicle and protect its finishes These quality products have been specifically engineered to fulfill your automotive needs they are custom designed to complement the style and appearance of your vehicle Each product is made from high quality materials that meet or exceed rigid specifications For best results use the following products or products of equivalent quality Motorcraft Bug and Tar Remover ZC 42 Motorcraft Car Care Kit ZC 26 Motorcraft Car Wash Canada only CXC 21 Motorcraft Custom Bright Metal Cleaner ZC 15 Motorcraft Custom Clear Coat Polish ZC 8 A Motorcraft Custom Vinyl Protectant U S only ZC 40 A Motorcraft Dash and Vinyl Cleaner ZC 38 A Motorcraft Deluxe Leather and Vinyl Cleaner U S only ZC 11 A Motorcraft Detail Wash ZC 3 A Motorcraft Dusting Cloth ZC 24 Motorcraft Engine Shampoo and Degreaser U S only ZC 20 Motorcraft Engine Shampoo Canada only CXC 66 A 194 Cleaning Motorcraft One Step Wash and Wax Concentrate ZC 6 A Motorcraft Paint Sealant ZC 45 Motorcraft Premium Car Wash Concentrate U S only ZC 17 B Motorcraft Premium Glass Cleaner Canada only CXC 100 Motorcraft Premium Liquid Wax ZC 53 A Motorcraft Premium Windshield Washer Concentrate ZC 32 A Motorcraft Professional Strength Carpet amp Upholstery Cleaner ZC 54 Motorcraft Spot and Stain Remover U S only ZC 14 Motorcraft Tire Clean and Shine ZC 28
89. e driving may reduce fuel economy Combine errands and minimize stop and go driving Maintenance Keep tires properly inflated and use only recommended size Operating a vehicle with the wheels out of alignment will reduce fuel economy Use recommended engine oil Refer to Lubricant specifications in this chapter Perform all regularly scheduled maintenance items Follow the recommended maintenance schedule and owner maintenance checks found in scheduled maintenance information Conditions Heavily loading a vehicle or towing a trailer may reduce fuel economy at any speed Carrying unnecessary weight may reduce fuel economy approximately 1 mpg 0 4 km L is lost for every 400 Ib 180 kg of weight carried Adding certain accessories to your vehicle for example bug deflectors rollbars light bars running boards ski luggage racks may reduce fuel economy 221 Maintenance and Specifications e Using fuel blended with alcohol may lower fuel economy e Fuel economy may decrease with lower temperatures during the first 8 10 miles 12 16 km of driving e Driving on flat terrain offers improved fuel economy as compared to driving on hilly terrain e Transmissions give their best fuel economy when operated in the top cruise gear and with steady pressure on the gas pedal e Close windows for high speed driving EPA window sticker Every new vehicle should have the EPA window sticker Contact your authorized dealer if
90. e of at least 10 inches 25 cm between an occupant s chest and the driver airbag module 97 Seating and Safety Restraints Never place your arm over the airbag module as a deploying airbag can result in serious arm fractures or other injuries To properly position yourself away from the airbag e Move your seat to the rear as far as you can while still reaching the pedals comfortably e Recline the seat slightly one or two degrees from the upright position Do not put anything on or over the airbag module Placing objects on or over the airbag inflation area may cause those objects to be propelled by the airbag into your face and torso causing serious injury Do not attempt to service repair or modify the airbag supplemental restraint systems or its fuses See your authorized dealer Modifying or adding equipment to the front end of the vehicle including frame bumper front end body structure and tow hooks may affect the performance of the airbag system increasing the risk of injury Do not modify the front end of the vehicle 98 Seating and Safety Restraints Children and airbags Children must always be properly restrained Accident statistics suggest that children are safer when properly restrained in the rear seating positions than in the front seating position Failure to follow these instructions may increase the risk of injury in a collision Airbags can kill or injure a child in a child sea
91. ead screwdriver remove the plastic cover 154 Driving 3 Insert the ignition key and push it straight down to release the interlock 4 Apply the parking brake then shift to N Neutral 5 Start the vehicle If it is necessary to use the above procedure to move the gearshift lever it is possible that a fuse has blown or the vehicle s brakelamps are not operating properly Refer to Fuses and relays in the Roadside Emergencies chapter Do not drive your vehicle until you verify that the brakelamps are working Always set the parking brake fully and make sure the gearshift is latched in P Park Turn the ignition to the LOCK position and remove the key whenever you leave your vehicle If the parking brake is fully released but the brake warning lamp remains illuminated the brakes may not be working properly See your authorized dealer 155 Driving Understanding the gearshift positions of the 5 speed automatic transmission 5 Wi J W NV This vehicle is equipped with an adaptive Transmission Shift Strategy Adaptive Shift Strategy offers the optimal transmission operation and shift quality When the vehicle s battery has been disconnected for any type of service or repair the transmission will need to relearn the normal shift strategy parameters much like having to reset your radio stations when your vehicle battery has been disconnected The Adaptive Transmission Strate
92. econds of illumination The dome lamp control must not be set to the off position for the illuminated entry system to operate The inside lights will not turn off if e they have been turned on with the dimmer control or e any door is open The battery saver will shut off the interior lamps 10 minutes after the ignition has been turned to the 1 OFF LOCK position and a door is left 70 Locks and Security open and in 30 minutes if the dome lamp control is left on and the ignition has been turned to the 1 OFF LOCK position The battery saver will also shut off the trunk lamps in 30 minutes if the trunk is left open SECURILOCK PASSIVE ANTI THEFT SYSTEM SecuriLock passive anti theft system is an engine immobilization system This system is designed to help prevent the engine from being started unless a coded key programmed to your vehicle is used The use of the wrong type of coded key may lead to a no start condition Your vehicle comes with two coded keys additional coded keys may be purchased from your authorized dealer The authorized dealer can program your spare keys to your vehicle or you can program the keys yourself Refer to Programming spare keys for instructions on how to program the coded key Note The SecuriLock passive anti theft system is not compatible with non Ford aftermarket remote start systems Use of these systems may result in vehicle starting problems and a loss of security protection
93. ed is not faster than 30 mph 48 km h Increasing speed while using speed control There are three ways to set a higher speed O Press and hold the SET control until you get to the desired speed then release the control e Press and release the SET control to operate the Tap Up function Each tap will increase the set speed by 1 mph 1 6 km h e Use the accelerator pedal to get to the desired speed When the vehicle reaches that speed press and release the SET control Reducing speed while using speed control There are three ways to reduce a RES set speed e Press and hold the SET control until you get to the desired speed then release the control D e Press and release the SET control to operate the Tap Down function Each tap will decrease the set speed by 1 mph 1 6 km h 48 Driver Controls e Depress the brake pedal until the desired vehicle speed is reached press the SET control Turning off speed control There are two ways to turn off the speed control control e Turn OFF the ignition Note When you turn off the speed control or the ignition your speed control set speed memory is erased CONVERTIBLE IF EQUIPPED Do not store articles behind rear seat Articles stored in the convertible top stowage compartment may break the rear glass window when the top is lowered e Press the speed control OFF C J Lowerin
94. ed life product with your factory filled coolant can result in degraded corrosion protection e A large amount of water without engine coolant may be added in case of emergency to reach a vehicle service location In this instance the cooling system must be drained and refilled with a 50 50 mixture of engine coolant and distilled water as soon as possible Water alone without engine coolant can cause engine damage from corrosion overheating or freezing e Do not use alcohol methanol brine or any engine coolants mixed with alcohol or methanol antifreeze coolant Alcohol and other liquids can cause engine damage from overheating or freezing e Do not add extra inhibitors or additives to the coolant These can be harmful and compromise the corrosion protection of the engine coolant For vehicles with overflow coolant systems with a non pressurized cap on the coolant recovery system add coolant to the coolant recovery reservoir when the engine is cool Add the proper mixture of coolant and water to the FULL COLD level For all other vehicles which have a coolant degas system with a pressurized cap or if it is necessary to remove the coolant pressure relief cap on the radiator of a vehicle with an overflow system follow these steps to add engine coolant 210 Maintenance and Specifications To reduce the risk of personal injury make sure the engine is cool before unscrewing the coolant pressure relief cap The cooling sys
95. el indicator dipstick 201 Maintenance and Specifications e 4 0L V6 engine ACY TL TRR NN A NI YV vs KOA Win e 4 6L 3V V8 engine 6 Wipe the indicator clean Insert the indicator fully then remove it again e If the oil level is between the lower and upper holes the oil level is acceptable DO NOT ADD OIL e If the oil level is below the lower hole add enough oil to raise the level within the lower and upper holes 202 Maintenance and Specifications e 4 0L V6 engine A N TA ex Sx S e 4 6L 3V SOHC V8 engine e Oil levels above the upper hole may cause engine damage Some oil must be removed from the engine by an authorized dealer 7 Put the indicator back in and ensure it is fully seated Adding engine oil 1 Check the engine oil For instructions refer to Checking the engine oil in this chapter 203 Maintenance and Specifications 2 If the engine oil level is not within the normal range add only certified engine oil of the recommended viscosity Remove the engine oil filler cap and use a funnel to pour the engine oil into the opening 3 Recheck the engine oil level Make sure the oil level is not above the normal operating range on the engine oil level indicator dipstick 4 Install the indicator and ensure it is fully seated 5 Fully install the en
96. em will automatically turn on every time the ignition is turned OFF and ON If you should become stuck in snow or ice or on a very slippery road surface try switching the Traction Control system off This may allow excess wheel spin to dig the vehicle out and enable a successful rocking maneuver TCS 110 The traction control on off status is shown by an indicator lamp on the traction control switch If the system is off the indicator will be illuminated If a system fault is detected the traction control active light will illuminate the Traction Control button will also illuminate and will not turn the system on or off and your vehicle should be serviced by an authorized dealer Aggressive driving in any road conditions can cause you to lose control of your vehicle increasing the risk of severe personal injury or property damage The occurrence of a Traction Control event is an indication that at least some of the tires have exceeded their ability to grip the road this may lead to an increased risk of loss of vehicle control vehicle rollover personal injury and death If you experience a severe road event SLOW DOWN STEERING To prevent damage to the power steering system e Never hold the steering wheel at its furthest turning points until it stops for more than a few seconds when the engine is running e Do not operate the vehicle with a low power steering pump reservoir fluid level below the MIN mar
97. en stationary and out of direct sunlight for an hour or more and prior to the vehicle being driven for 1 mile 1 6 km e Recommended inflation pressure The cold inflation pressure found on the Safety Compliance Certification Label or Tire Label located on the B Pillar or the edge of the driver s door e B pillar The structural member at the side of the vehicle behind the front door e Bead area of the tire Area of the tire next to the rim e Sidewall of the tire Area between the bead area and the tread e Tread area of the tire Area of the perimeter of the tire that contacts the road when mounted on the vehicle e Rim The metal support wheel for a tire or a tire and tube assembly upon which the tire beads are seated INFLATING YOUR TIRES Safe operation of your vehicle requires that your tires are properly inflated Remember that a tire can lose up to half of its air pressure without appearing flat Every day before you drive check your tires If one looks lower than the others use a tire gauge to check pressure of all tires and adjust if required At least once a month and before r long trips inspect each tire and KK check the tire pressure with a tire gauge including spare if equipped Inflate all tires to the inflation pressure recommended by Ford Motor Company Use a tire gauge to check the tire inflation pressure including the spare if equipped at least monthly and before long trips You are strong
98. en the ignition is in the ON position The fuel gauge may vary slightly when the Y vehicle is in motion or on a grade N The FUEL icon and arrow indicates which side of the vehicle the fuel filler door is located Refer to Filling the tank in the Maintenance and Specifications chapter for more information 18 Entertainment Systems AUDIO SYSTEMS AM FM stereo single CD sound system if equipped SG CY cD MUTE om AM MENG FM AUX l 5 VOL PUSH REW FF REPEAT COMP SHUFFLE TEXT 1 2 3 4 5 6 Accessory delay Your vehicle is equipped with accessory delay With this feature the window switches and radio may be used for up to ten minutes after the ignition switch is turned to the OFF position or until any door or trunk is opened LA W Tuner Press to manually go up or down the radio frequency Also use in menu mode to select various settings 2 Phone mute Press to mute the playing media Press again to return to the playing media 3 Menu Press to toggle through the following modes Bass Press to adjust the bass setting Use A IV q SEEKD Treble Press to adjust the treble setting Use A IV 4 SEEK gt 19 Entertainment Systems Balance Press to adjust the audio between the left and right speakers Use A W lt SEEK Fade Press to adjust the audio between the front and rear speakers Use A W lt SEEK Speed sensitive volume Ra
99. er to scheduled maintenance information to determine the correct service interval 233 Maintenance and Specifications ENGINE DATA Engine 4 0L V6 engine 4 6L V8 engine Spark plug gap 0 052 0 056 inch 0 040 0 050 inch See emmo aotan The spark plug gap is not adjustable on the 4 6L V8 ENGINE DRIVEBELT ROUTING e 4 0L V6 Engine e 4 6L V8 Engine 234 Maintenance and Specifications VEHICLE DIMENSIONS Vehicle dimensions Base inches mm GT inches mm 1 Vehicle height 55 4 1408 55 4 1408 2 Tread Width 62 8 1594 62 3 1582 Front 235 Maintenance and Specifications lt 5 IDENTIFYING YOUR VEHICLE Safety Compliance Certification Label The National Highway Traffic Safety Administration Regulations require MFD BY FORD MOTOR CO IN U S A that a Safety Compliance DATE XXXXX GVWR XXXXX LB XXXXX KG reat FGAWR XXXXXX XXXXXXX RGAWR XXXXXXX XXXXXXX Certification Label be affixed to a THIS VEHICLE CONFORMS TO ALL APPLICABLE FEDERAL MOTOR VEHICLE SAFETY STANDARDS IN EFFECT ON THE vehicle and pr escribe where the DATE OF MANUFACTURE SHOWN ABOVE Safety Compliance Certification VIN XXXXXXXXXXXXXXXXX TYPE XXXXXXXXXXXXXXX Label may be located The Safety UI AMMA O ON TTY NOT LIT Compliance Certification Label is MAXIMUM LOAD OCCUPANTS LUGGAGE XXXKG XXXXLB OCCUPANTS X TOTAL X FR X 2ND X RR OCCUPANTS LUG
100. ernal transmission components 145 Driving STARTING Positions of the ignition 1 OFF LOCK locks the steering wheel automatic transmission gearshift lever and allows key removal Note The ignition key cannot be removed from the ignition unless the gearshift lever is securely latched in P Park 2 ACCESSORY allows the electrical accessories such as the radio to operate while the engine is not running 3 ON all electrical circuits operational Warning lights illuminated Key position when driving 4 START cranks the engine Release the key as soon as the engine starts Preparing to start your vehicle Engine starting is controlled by the powertrain control system This system meets all Canadian Interference Causing Equipment standard requirements regulating the impulse electrical field strength of radio noise When starting a fuel injected engine don t press the accelerator before or during starting Only use the accelerator when you have difficulty starting the engine For more information on starting the vehicle refer to Starting the engine in this chapter Extended idling at high engine speeds can produce very high temperatures in the engine and exhaust system creating the risk of fire or other damage Do not park idle or drive your vehicle in dry grass or other dry ground cover The emission system heats up the engine compartment and exhaust system which can start a fire 146 Driving Do
101. ers Use A W lt SEEK 24 Entertainment Systems Occupancy mode Use A IV la SEEK p select and optimize sound for ALL SEATS DRIVERS SEAT or REAR SEATS Speed sensitive volume Radio volume changes automatically and slightly with vehicle speed to compensate for road and wind noise Recommended level is 1 3 Level 0 turns the feature off and level 7 is the maximum setting Press MENU to access and use A IV 4 SEEK gt to adjust the volume setting The level will appear in the display RDS Available only in FM mode This feature allows you to search RDS equipped stations for a certain category of music format Classic Country Info Jazz RB Religious Rock Soft Top 40 RDS must be activated to access Find and Show functions To activate press and hold MENU until RDS ON OFF appears in the display Press MENU repeatedly to scroll through Find Show and RDS Use A V lt SEEK to toggle RDS ON OFF When RDS is Off you will not be able to access Find and Show functions Find Allows you to search RDS equipped stations for the desired music category Use A IV to find the desired program type then use A SEEK gt or SCAN to begin the search Show Allows you to display the name of the radio station or program type Use A IV 4 SEEK Pe to show type name or none 4 Aux If no auxiliary sources are available NO AUX AUDIO will be displayed 5 Seek Press to access the next strong station or track Also use in
102. es information about the performance or status of various systems and modules in the vehicle such as engine throttle steering or brake systems In order to properly diagnose and service your vehicle Ford Motor Company Ford of Canada and service and repair facilities may access vehicle diagnostic information through a direct connection to your vehicle when diagnosing or servicing your vehicle Event Data Recording Other modules in your vehicle event data recorders are capable of collecting and storing data during a crash or near crash event The recorded information may assist in the investigation of such an event The modules may record information about both the vehicle and the occupants potentially including information such as e how various systems in your vehicle were operating e whether or not the driver and passenger seatbelts were buckled e how far if at all the driver was depressing the accelerator and or the brake pedal e how fast the vehicle was traveling and e where the driver was positioning the steering wheel Introduction To access this information special equipment must be directly connected to the recording modules Ford Motor Company and Ford of Canada do not access event data recorder information without obtaining consent unless pursuant to court order or where required by law enforcement other government authorities or other third parties acting with lawful authority Other parties may seek to
103. etent to activate Pull the lever towards you again to deactivate Flash to pass Pull toward you to the first detent to activate and release to deactivate Daytime running lamps DRL if equipped Turns the headlamps on with a reduced output When activated the DRL telltale is illuminated To activate e the ignition must be in the ON position 33 Lights e the headlamp control is in the OFF or parking lamp position and e the parking brake must be disengaged Always remember to turn on your headlamps at dusk or during inclement weather The Daytime Running Lamp DRL system does not activate the tail lamps and generally may not provide adequate lighting during these conditions Failure to activate your headlamps under these conditions may result in a collision Foglamp control if equipped 0 The foglamps can be turned on when the headlamp control is in the PS orgD position and the high beams are not on Pull the headlamp control towards you to turn on the foglamps The indicator light under the foglamp symbol will illuminate PANEL DIMMER CONTROL Use to adjust the brightness of the instrument panel and all applicable switches in the vehicle during headlamp and parklamp operation Move the control to the full upright position past detent to turn on the interior lamps AIMING THE HEADLAMPS The headlamps on your vehicle are properly aimed at the assembly plant If your vehicle ha
104. ety Belt section in this chapter Front safety belt pretensioners The front outboard safety belt pretensioners are designed to tighten the safety belts firmly against the occupant s body during a collision This maximizes the effectiveness of the safety belts and helps properly position the occupant relative to the airbag to improve protection The safety belt pretensioners can be either activated alone or if the collision is of sufficient severity together with the airbags Front safety belt energy management retractors The front outboard safety belt energy management retractors allow webbing to be pulled out of the retractor in a gradual and controlled manner in response to the occupant s forward momentum This helps reduce the risk of force related injuries to the occupant s chest by limiting the load on the occupant Refer to Safety Belt section in this chapter Determining if the Personal Safety System is operational The Personal Safety System uses a warning light in the instrument cluster or a back up tone to indicate the condition of the system Refer to the Warning Light section in the Instrument Cluster chapter Routine maintenance of the Personal Safety System is not required 84 Seating and Safety Restraints The Restraints Control Module RCM monitors its own internal circuits and the circuits for the airbag supplemental restraints crash sensor s safety belt pretensioners front safety belt buckle senso
105. eways sits forward leans forward or sideways or puts one or both feet up the chance of injury during a crash is greatly increased Sitting improperly out of position or with the seat back reclined too far can take off weight from the seat cushion and affect the decision of the front passenger sensing system resulting in serious injury or death in a crash Always sit upright against your seatback with your feet on the floor The front passenger sensing system may detect small or medium objects placed on the seat cushion For most objects that are in the front passenger seat the passenger airbag will be disabled Even though the passenger airbag is disabled the pass airbag off lamp may or may not be illuminated according to the table below Small G e 3 ring Unlit Eanes binder small purse bottled water Medium i e heavy Disabled briefcase fully packed luggage Empty seat Small or Lit Disabled medium object with safety belt buckled If you think that the status of the passenger airbag off indicator lamp is incorrect check for the following e Objects lodged underneath the seat e Objects between the seat cushion and the center console if equipped 103 Seating and Safety Restraints Objects hanging off the seat back e Objects stowed in the seatback map pocket if equipped e Objects placed on the occupant s lap e Cargo interference with the seat e Other passengers pushing or pulling on the sea
106. f the impact This allows your Personal Safety System to distinguish between different levels of crash severity and modify the deployment strategy of the dual stage airbags and safety belt pretensioners Driver s seat position sensor The driver s seat position sensor allows your Personal Safety System to tailor the deployment level of the driver dual stage airbag based on seat position The system is designed to help protect smaller drivers sitting close to the driver airbag by providing a lower airbag output level Front passenger sensing system For airbags to do their job they must inflate with great force and this force can pose a potentially deadly risk to occupants that are very close to the airbag when it begins to inflate For some occupants like infants in rear facing child seats this occurs because they are initially sitting very close to the airbag For other occupants this occurs when the occupant is not properly restrained by seat belts or child safety seats and they move forward during pre crash braking The most effective way to reduce the risk of unnecessary injuries is to make sure all occupants are properly restrained Accident statistics suggest that children are much safer when properly restrained in the rear seating positions than in the front Air bags can kill or injure a child in a child seat NEVER place a rear facing child seat in front of an active air bag If you must use a forward facing child seat in
107. g the convertible top The convertible top can be lowered with the side windows down The windows will automatically lower when lowering or raising the top The convertible top will not operate unless the vehicle is traveling under 3 1 mph 5 km h Do not lower the top when the top material is wet To lower the convertible top 1 Bring vehicle to a complete stop Key must be in the ON position It is recommended that the vehicle s engine is running when lowering the top to prevent draining the battery 2 Check the convertible top stowage compartment behind the rear seat to be sure it is empty and ready to receive the top Check the convertible top outer surface to be sure it is free of leaves and debris 49 Driver Controls The latch handles must be pulled downwards fully to allow the latch to fully rotate into the open position 3 Unclamp the top from the windshield header by pulling each latch handle down and then rotating the latch to the rear until it clears the header Note If the top has not been lowered for some time and sticks to the windshield header push the front of the top up slightly with your hand to loosen it 4 Push the convertible top switch on the overhead console and hold until the windows are completely down and the top is completely stored 50 Driver Controls Installation of the boot if equipped Be sure the boot is secure on the vehicle before driving 1 Install the boot o
108. ge is displayed check the level of the engine oil Refer to Engine oil in the Maintenance and Specifications chapter for information about adding engine oil If the oil level is OK and this warning persists shut down the engine immediately and contact your authorized dealer for service CHECK FUEL CAP Displayed when the fuel filler cap is not properly installed Check the fuel filler cap for proper installation Refer to Fuel filler cap under the Fuel Information section in the Maintenance and Specifications chapter CHECK TRACTION CONTROL Displayed when the Traction Control system is not operating properly If this message is displayed on the message center the Traction Control system will be partially operable If this warning stays on contact your authorized dealer for service as soon as possible For further information refer to Traction control in the Driving chapter TURN SIGNAL ON REMINDER Displayed when the turn signal is activated and the vehicle is driven more that 1 2 mile 0 8 km 61 Driver Controls POSITIVE RETENTION FLOOR MAT IF EQUIPPED A Only use one set of floor mats at any given time Position the floor mat so that the 4 eyelet is over the pointed end of the retention post and rotate forward to gt lock in Make sure that the mat does not interfere with the operation of the accelerator or the brake pedal To remove the floor mat reverse the installation procedure Note Do not install addi
109. gine oil filler cap by turning the filler cap clockwise 1 4 of a turn until three clicks are heard or until the cap is fully seated To avoid possible oil loss DO NOT operate the vehicle with the engine oil level indicator and or the engine oil filler cap removed Engine Oil Recommendations 4 6L 3V V8 Engine Look for this certification trademark Use SAE 5W 20 engine oil Only use oils Certified For Gasoline Engines by the American Petroleum Institute API An oil with this trademark symbol conforms to the current engine and emission system protection standards and fuel economy requirements of the International Lubricant Standardization and Approval Committee ILSAC comprised of U S and Japanese automobile manufacturers To protect your engine s warranty use Motorcraft SAE 5W 20 or an equivalent 5W 20 oil meeting Ford specification WSS M2C930 A SAE 5W 20 oil provides optimum fuel economy and durability performance meeting all requirements for your vehicle s engine Do not use supplemental engine oil additives cleaners or other engine treatments They are unnecessary and could lead to engine damage that is not covered by Ford warranty Change your engine oil according to the appropriate schedule listed in the scheduled maintenance information 204 Maintenance and Specifications 4 0L V6 Engine Look for this certification trademark Use SAE 5W 30 engine oil Only use oils Certified Fo
110. gy allows the transmission to relearn these operating parameters This learning process could take several transmission upshifts and downshifts during this learning process slightly firmer shifts may occur After this learning process normal shift feel and shift scheduling will resume P Park This position locks the transmission and prevents the rear wheels from turning To put your vehicle in gear e Start the engine e Depress the brake pedal e Move the gearshift lever into the desired gear 156 Driving To put your vehicle in P Park e Come to a complete stop e Move the gearshift lever and securely latch it in P Park Always set the parking brake fully and make sure the gearshift is latched in P Park Turn the ignition to the LOCK position and remove the key whenever you leave your vehicle R Reverse With the gearshift lever in R Reverse the vehicle will move backward Always come to a complete stop before shifting into and out of R Reverse N Neutral With the gearshift lever in N Neutral the vehicle can be started and is free to roll Hold the brake pedal down while in this position D Drive with Overdrive The normal driving position for the best fuel economy Transmission operates in gears one through five D Drive without Overdrive D Drive with Overdrive can be deactivated by pressing the transmission control switch on the right side of the shift handle
111. h a wheel lift and dollies or flatbed equipment Do not tow with a slingbelt Ford Motor Company has not approved a slingbelt towing procedure If your vehicle is to be towed from the front using wheel lift equipment it is recommended that the rear wheels drive wheels be placed on a dolly to prevent damage to the transmission If the vehicle is towed by other means or incorrectly vehicle damage may occur Ford Motor Company produces a towing manual for all authorized tow truck operators Have your tow truck operator refer to this manual for proper hook up and towing procedures for your vehicle 181 Customer Assistance GETTING THE SERVICES YOU NEED At home You must take your Ford vehicle to an authorized dealer for warranty repairs While any authorized dealer handling your vehicle line will provide warranty service we recommend you return to your selling authorized dealer who wants to ensure your continued satisfaction Please note that certain warranty repairs require special training and or equipment so not all authorized dealers are authorized to perform all warranty repairs This means that depending on the warranty repair needed you may have to take your vehicle to another authorized dealer A reasonable time must be allowed to perform a repair after taking your vehicle to the authorized dealer Repairs will be made using Ford or oo parts or remanufactured or other parts that are authorized by ord If you have questio
112. h has a tire inflation kit e battery jump start e lock out assistance key replacement cost is the customer s responsibility e fuel delivery Independent Service Contractors if not prohibited by state local or municipal law shall deliver up to 2 0 gallons 7 5L of gasoline or 5 gallons 18 9L of diesel fuel to a disabled vehicle e winch out available within 100 feet 80 5 meters of a paved or county maintained road no recoveries e towing Ford Mercury Lincoln eligible vehicle towed to an authorized dealer within 35 miles 56 3 km of the disablement location or to the nearest authorized dealer If a member requests to be towed to an authorized dealer more than 35 miles 56 3 km from the disablement location the member shall be responsible for any mileage costs in excess of 35 miles 56 3 km Trailers shall be covered up to 100 if the disabled eligible vehicle requires service at the nearest authorized dealer If the trailer is disabled but the towing vehicle is operational the trailer does not qualify for any roadside services Canadian customers refer to your Owner Information Guide for information on e coverage period e exact fuel amounts 162 Roadside Emergencies e towing of your disabled vehicle e emergency travel expense reimbursement e travel planning benefits Using roadside assistance Complete the roadside assistance identification card and place it in your wallet for quick reference In
113. h or remains IN on have the system serviced immediately by your authorized dealer A chime will also sound when a malfunction in the supplemental restraint system has been detected Safety belt Reminds you to fasten your safety belt A chime will also sound to remind you to fasten your safety belt Charging system Illuminates when agers the battery is not charging properly Engine oil pressure if equipped IJluminates when the oil T pressure falls below the normal range refer to Engine oil in the Maintenance and Specifications chapter Engine coolant temperature Illuminates when the engine coolant E temperature is high Stop the vehicle as soon as possible switch off the engine and let cool Refer to Engine coolant in the Maintenance and Specifications chapter Never remove the coolant reservoir cap while the engine is running or hot 12 Instrument Cluster Traction Control active Flashes when the Traction Control is n active If the light remains on a malfunction has been detected have the system serviced immediately refer to the Driving chapter for more information Overdrive off automatic 0 D transmission luminates when the overdrive function of the OFF transmission has been turned off refer to the Driving chapter If the light flashes steadily or does not illuminate have the transmission serviced soon or damage may occur Low fuel if equipped Illuminates when the fuel
114. he tongue is securely fastened in the buckle Keep the buckle release button pointing up and away from the safety seat with the tongue between the child seat and the release button to prevent accidental unbuckling Place seat back in upright position Put the safety belt in the automatic locking mode Refer to Automatic locking mode passenger side front and outboard rear seating positions Gif equipped section in this chapter LATCH lower anchors are recommended for use by children up to 48 Ib 22 kg in a child restraint Top tether anchors can be used for children up to 60 lb 27 kg in a child restraint and to provide upper torso restraint for children up to 80 Ib 86 kg using an upper torso harness and a belt positioning booster Ford recommends the use of a child safety seat having a top tether strap Install the child safety seat in a seating position with LATCH and 112 Seating and Safety Restraints tether anchors For more information on top tether straps and anchors refer to Attaching safety seats with tether straps in this chapter For more information of LATCH anchors refer to Attaching safety seats with LATCH Lower Anchors and Tethers for Children attachments in this chapter Carefully follow all of the manufacturer s instructions included with the safety seat you put in your vehicle If you do not install and use the safety seat properly the child may be injured in a sudden stop or collision Rear f
115. hicle s color Take your color code printed on a sticker in the driver s door jamb to your authorized dealer to ensure you get the correct color 189 Cleaning e Remove particles such as bird droppings tree sap insect deposits tar spots road salt and industrial fallout before repairing paint chips e Always read the instructions before using the products ALUMINUM WHEELS AND WHEEL COVERS Aluminum wheels and wheel covers are coated with a clearcoat paint finish In order to maintain their shine e Clean weekly with Motorcraft Wheel and Tire Cleaner ZC 37 A which is available from your authorized dealer Heavy dirt and brake dust accumulation may require agitation with a sponge Rinse thoroughly with a strong stream of water e Never apply any cleaning chemical to hot or warm wheel rims or covers e Some automatic car washes may cause damage to the finish on your wheel rims or covers Chemical strength cleaners or cleaning chemicals in combination with brush agitation to remove brake dust and dirt could wear away the clearcoat finish over time e Do not use hydrofluoric acid based or high caustic based wheel cleaners steel wool fuels or strong household detergent e To remove tar and grease use Motorcraft Bug and Tar Remover ZC 42 available from your authorized dealer ENGINE Engines are more efficient when they are clean because grease and dirt buildup keep the engine warmer than normal When washing e
116. hield and use the lap shoulder belt If a seating position has a low seat back and no head restraint a backless booster seat may place your child s head top of ear level above the top of the seat In this case move the backless booster to another seating position with a higher seat back and lap shoulder belts Those with a high back If with a backless booster seat you cannot find a seating position that adequately supports your child s head a high back booster seat would be a better choice Either type can be used at any seating position equipped with lap shoulder belts if your child is over 40 lb 18 kg 110 Seating and Safety Restraints Children and booster seats vary widely in size and shape Choose a booster that keeps the lap belt low and snug across the hips never up across the stomach and lets you adjust the shoulder belt to cross the chest and rest snugly near the center of the shoulder The drawings below compare the ideal fit center to a shoulder belt uncomfortably close to the neck and a shoulder belt that could slip off the shoulder If the booster seat slides on the vehicle seat placing a rubberized mesh sold as shelf or carpet liner under the booster seat may improve this condition The importance of shoulder belts Using a booster without a shoulder belt increases the risk of a child s head hitting a hard surface in a collision For this reason you should never use a booster seat
117. horized dealer to verify that the automatic locking retractor feature for child seats is still functioning properly In addition all safety belts should be checked for proper function BELT AND RETRACTOR ASSEMBLY MUST BE REPLACED if the safety belt assembly automatic locking retractor feature or any other safety belt function is not operating properly when checked by an authorized dealer Failure to replace the Belt and Retractor assembly could increase the risk of injury in collisions The front and rear safety restraints in the vehicle are combination lap and shoulder belts The front passenger and rear seat safety belts have two types of locking modes described below Vehicle sensitive mode This is the normal retractor mode which allows free shoulder belt length adjustment to your movements and locking in response to vehicle movement For example if the driver brakes suddenly or turns a corner sharply or the vehicle receives an impact of approximately 5 mph 8 km h or more the combination safety belts will lock to help reduce forward movement of the driver and passengers Automatic locking mode The automatic locking mode is not available on the driver safety belt When to use the automatic locking mode In this mode the shoulder belt is automatically pre locked The belt will still retract to remove any slack in the shoulder belt The automatic locking mode is not available on the driver safety belt 88 Seating a
118. ht by at least 240 Ib 104 kg If you remove 3 100 lb 45 kg cement bags then the load calculation would be 1400 2 x 220 9 x 100 1400 440 900 60 lb Now you have the load capacity to transport the cement and your friend home In metric units the calculation would be 635 kg 2 x 99 kg 9 x 45 kg 635 198 405 32 kg The above calculations also assume that the loads are positioned in your vehicle in a manner that does not overload the Front or the Rear Gross Axle Weight Rating specified for your vehicle on the Safety Compliance Certification Label found on the edge of the driver s door TRAILER TOWING Your vehicle is capable of towing a trailer up to 1 000 lb 454 kg gross trailer weight with a maximum tongue load of 100 Ib 45 kg Do not tow a trailer until your vehicle has been driven at least 500 miles 800 km Towing a trailer places an additional load on your vehicle s engine transmission brakes tires and suspension Inspect these components carefully after towing 142 Tires Wheels and Loading Do not exceed the GVWR or the GAWR specified on the certification label Towing trailers beyond the maximum recommended gross trailer weight exceeds the limit of the vehicle and could result in engine damage transmission damage structural damage loss of vehicle control vehicle rollover and personal injury Preparing to tow Use the proper equipment for towing a trai
119. icle be operated in 4WD modes with a temporary emergency spare tire If 4WD operation is necessary do not operate above speeds of 10 mph 16 km h or for distances above 50 miles 80 km 3 Full size dissimilar spare without label on wheel When driving with the full size dissimilar spare tire wheel do not Exceed 70 mph 113 km h e Use more than one dissimilar spare tire wheel at a time Use commercial car washing equipment Use snow chains on the end of the vehicle with the dissimilar spare tire wheel The usage of a full size dissimilar spare tire wheel can lead to impairment of the following Handling stability and braking performance Comfort and noise Ground clearance and parking at curbs Winter weather driving capability Wet weather driving capability e All Wheel driving capability Gf applicable e Load leveling adjustment if applicable 172 Roadside Emergencies When driving with the full size dissimilar spare tire wheel additional caution should be given to Towing a trailer e Driving vehicles equipped with a camper body Driving vehicles with a load on the cargo rack Drive cautiously when using a full size dissimilar spare tire wheel and seek service as soon as possible How to change a flat tire To help prevent the vehicle from moving when you change a tire be sure the parking brake is set then block Gn both directions the wheel that is diagonally opposite other side and
120. ighlighted in this guide with the tree symbol BREAKING IN YOUR VEHICLE Your vehicle does not need an extensive break in Try not to drive continuously at the same speed for the first 1 000 miles 1 600 km of new vehicle operation Vary your speed frequently in order to give the moving parts a chance to break in Do not add friction modifier compounds or special break in oils during the first few thousand miles kilometers of operation since these additives may prevent piston ring seating See Engine oil in the Maintenance and Specifications chapter for more information on oil usage SPECIAL NOTICES New Vehicle Limited Warranty For a detailed description of what is covered and what is not covered by your vehicle s New Vehicle Limited Warranty refer to the Warranty Guide that is provided to you along with your Owner s Guide Introduction Special instructions For your added safety your vehicle is fitted with sophisticated electronic controls Please read the section Supplemental restraint system SRS in the Seating and Safety Restraints chapter Failure to follow the specific warnings and instructions could result in personal injury Front seat mounted rear facing child or infant seats should NEVER be placed in front of an active passenger airbag Service Data Recording Service data recorders in your vehicle are capable of collecting and storing diagnostic information about your vehicle This potentially includ
121. in the cooling system may harm engine and cooling system components 200 Maintenance and Specifications CHANGING THE WIPER BLADES 1 Pull the wiper arm away from the vehicle Turn the blade at an angle from the wiper arm Push the lock pin manually to release the blade and pull the wiper blade down _ toward the windshield to remove it from the arm 2 Attach the new wiper to the wiper arm and press it into place until a click is heard Replace wiper blades at least once per year for optimum performance Poor wiper quality can be improved v v by cleaning the wiper blades and the windshield refer to Windows and wiper blades in the Cleaning chapter To prolong the life of the wiper blades it is highly recommended to scrape off the ice on the windshield before turning on the wipers The layer of ice has many sharp edges and can damage the micro edge of the wiper rubber element ENGINE OIL 7 Checking the engine oil Refer to the scheduled maintenance information for the appropriate intervals for checking the engine oil 1 Make sure the vehicle is on level ground 2 Turn the engine off and wait 5 to 10 minutes for the oil to drain into the oil pan 3 Set the parking brake and ensure the gearshift is securely latched in P Park automatic transmissions or 1 First manual transmissions 4 Open the hood Protect yourself from engine heat 5 Locate and carefully remove the engine oil lev
122. ing chime Sounds when the key is left in the ignition in the OFF LOCK or ACCESSORY position and the driver s door is opened Headlamps on warning chime Sounds when the headlamps or parking lamps are on the ignition is off the key is not in the ignition and the driver s door is opened 14 Instrument Cluster GAUGES Base instrument cluster gauges Refer to Message Center if equipped in the Driver Controls chapter to select one of six preset colors or one user definable color MyColor for the nighttime gauge backlighting 15 Instrument Cluster Speedometer Indicates the current vehicle speed e Base instrument cluster e Optional instrument cluster Engine coolant temperature gauge Indicates engine coolant temperature At normal operating temperature the needle will be in AN the normal range between H and V C If it enters the red section the Y engine is overheating Stop the vehicle as soon as safely possible switch off the engine and let the engine cool Never remove the coolant reservoir cap while the engine is running or hot Odometer Registers the total miles kilometers of the vehicle e Base instrument cluster 16 Instrument Cluster e Optional instrument cluster Refer to Message Center in the 000 0 TRIP Driver Controls chapter on how to i switch the display from Metric to Ooocod m English Trip odometer Registers the miles kilometers of individual journeys
123. ing for trailer lamps Your vehicle uses an advanced electronic module to control and monitor your vehicle lamps Splicing into the wiring or attaching wiring to the vehicle bulb may DISABLE the rear vehicle lamps or cause them not to function properly See your authorized dealer for proper instructions and equipment for hooking up trailer lamps Driving while you tow When towing a trailer e Turn off the speed control The speed control may shut off automatically when you are towing on long steep grades e Consult your local motor vehicle speed regulations for towing a trailer e Shift out of D Overdrive into D Overdrive cancelled or a lower gear 8 2 or 1 when towing up or down steep hills This will eliminate excessive downshifting and upshifting for optimum fuel economy and transmission cooling e Anticipate stops and brake gradually Servicing after towing If you tow a trailer for long distances your vehicle will require more frequent service intervals Refer to your scheduled maintenance information for more information Trailer towing tips e Practice turning stopping and backing up before starting on a trip to get the feel of the vehicle trailer combination When turning make wider turns so the trailer wheels will clear curbs and other obstacles e Allow more distance for stopping with a trailer attached e The trailer tongue weight should be 10 15 of the loaded trailer weight e After you have traveled 50
124. ing locations and increases the signal to the trunk mounted speakers and amplifiers for enhanced bass performance Use A IV or lt Q SEEK P gt to toggle SHAKER mode on off Track Folder Mode Available only on MP3 discs in CD mode In Track Mode pressing lt SEEK gt will scroll through all tracks on the disc In Folder mode pressing lt SEEK pe will scroll only through tracks within the selected folder Compression Available only in CD mode brings soft and loud CD passages together for a more consistent listening level Repeat Available only in CD mode Press to repeat the current CD track Autoset Allows you to set the strongest local radio stations without losing your original manually set preset stations for AM FM1 FM2 Press MENU to access Use A IV 4 F SEEK gt to set or turn on off When the six strongest stations are filled the station stored in preset 1 will begin playing If there are less than six strong stations the system will store the last one in the remaining presets You can then access the stations by pressing the memory presets To disengage press MENU to access and press A IV 4 SEEK p gt to turn the feature off Bass Press to adjust the bass setting Use A IV 4 SEEK gt Treble Press to adjust the treble setting Use A IV 4 SEEK gt Balance Press to adjust the audio between the left and right speakers Use A W lt SEEK Fade Press to adjust the audio between the front and rear speak
125. ing the top to prevent draining the battery 2 Push the convertible top switch holding it until the windows lower completely and the top unfolds and moves forward toward the windshield header 3 You can release the convertible top switch to open both latch handles before the top meets the windshield header Make sure the latch handles are pulled down fully for hand clearance and are swung to the fully open position Note If the top has been in the down position for an extended period or if the temperature is low the top material may shrink a small amount Pulling down on the latch handles and at the center grip in the header will make it easier to fasten the top 4 Continue to use the convertible top switch to raise the top until it has reached the fully closed position flush to the header Note The two pins under the forward edge of the top should seat themselves in the matching holes in the header The latch handles must be pulled downwards fully to allow the latch to fully rotate into the closed position 5 Secure the Driver s side latch first then secure the Passenger side Pull Se lt lt _ down firmly on the latch handles before rotating them into the n windshield header until they reach a TC the full forward position Pulling be Ir S down on the latch handles and at pe Ve the center grip in the header will make it easier to fasten the top 6 Raise the front and rear side windows 53 D
126. install the cap on the filler pipe and turn it clockwise until at least one click is heard If the R indicator comes on and stays on after you start the engine the fuel filler cap may not be properly installed Turn off the engine remove the fuel filler cap align the cap properly and reinstall it 216 Maintenance and Specifications If you must replace the fuel filler cap replace it with a fuel filler cap that is designed for your vehicle The customer warranty may be void for any damage to the fuel tank or fuel system if the correct genuine Ford or Motorcraft fuel filler cap is not used The fuel system may be under pressure If the fuel filler cap is venting vapor or if you hear a hissing sound wait until it stops before completely removing the fuel filler cap Otherwise fuel may spray out and injure you or others If you do not use the proper fuel filler cap excessive pressure or vacuum in the fuel tank may damage the fuel system or cause the fuel cap to disengage in a collision which may result in possible personal injury bp Choosing the right fuel Use only UNLEADED FUEL The use of leaded fuel is prohibited by law and could damage your vehicle Your vehicle was not designed to use fuel or fuel additives with metallic compounds including manganese based additives Studies indicate that these additives can cause your vehicle s emission control system to deteriorate more rapidly In Canada premium grade fuel general
127. k on the reservoir If the power steering system breaks down or if the engine is turned off you can steer the vehicle manually but it takes more effort 153 Driving If the steering wanders or pulls check for e an improperly inflated tire e uneven tire wear e loose or worn suspension components e loose or worn steering components e improper steering alignment A high crown in the road or high crosswinds may also make the steering seem to wander pull TRACTION LOK AXLE IF EQUIPPED This axle provides added traction on slippery surfaces particularly when one wheel is on a poor traction surface Under normal conditions the Traction Lok axle functions like a standard rear axle Extended use of other than the manufacturer s specified size tires on a Traction Lok rear axle could result in a permanent reduction in effectiveness This loss of effectiveness does not affect normal driving and should not be noticeable to the driver AUTOMATIC TRANSMISSION OPERATION IF EQUIPPED Brake shift interlock This vehicle is equipped with a brake shift interlock feature that prevents the gearshift lever from being moved from P Park when the ignition is in the ON position unless the brake pedal is depressed If you cannot move the gearshift lever out of P Park with ignition in the ON position and the brake pedal depressed 1 Apply the parking brake turn ignition key to LOCK then remove the key 2 Using a flat h
128. k the booster vehicle close to the hood of the disabled vehicle making sure the two vehicles do not touch Set the parking brake on both vehicles and stay clear of the engine cooling fan and other moving parts 4 Check all battery terminals and remove any excessive corrosion before you attach the battery cables Ensure the vent caps are tight and level 5 Turn the heater fan on in both vehicles to protect any electrical surges Turn all other accessories off Connecting the jumper cables 1 Connect the positive jumper cable to the positive terminal of the discharged battery Note In the illustrations lightning bolts are used to designate the assisting boosting battery 177 Roadside Emergencies 2 Connect the other end of the positive cable to the positive terminal of the assisting battery 3 Connect the negative cable to the negative terminal of the assisting battery 4 Make the final connection of the negative cable to an exposed metal part of the stalled vehicle s engine away from the battery and the carburetor fuel injection system Do not use fuel lines engine rocker covers or the intake manifold as grounding points Do not connect the end of the second cable to the negative terminal of the battery to be jumped A spark may cause an explosion of the gases that surround the battery 5 Ensure that the cables are clear of fan blades belts moving parts of
129. l front and rear direction signals will flash Press the flasher control again to turn them off Use it when your vehicle is disabled and is creating a safety hazard for other motorists 163 Roadside Emergencies Note With extended use the flasher may run down your battery FUEL PUMP SHUT OFF SWITCH Ue This device stops the electric fuel pump from sending fuel to the engine when your vehicle has had a substantial jolt After an accident if the engine cranks but does not start this switch may have been activated S02 SU ae lt lt The fuel pump shut off switch is located in the driver s footwell by the hood release To reset the switch 1 Turn the ignition OFF 2 Check the fuel system for leaks 3 If no leaks are apparent reset the switch by pushing in on the reset button 4 Turn the ignition ON 5 Wait a few seconds and return the key to OFF 6 Make another check for leaks FUSES AND RELAYS Fuses If electrical components in the vehicle are not working a fuse may have blown Blown fuses are identified by a broken wire within the fuse Check the appropriate 15 fuses before replacing any electrical components Note Always replace a fuse with one that has the specified amperage rating Using a fuse with a higher amperage rating can cause severe wire damage and could start a fire 164 Roadside Emergencies Standard fuse
130. lable amount of cargo and luggage load capacity e Another example for your vehicle with 1400 Ib 635 kg of cargo and luggage capacity You decide to go golfing Is there enough load capacity to carry you 4 of your friends and all the golf bags You and four friends average 220 lb 99 kg each and the golf bags weigh approximately 30 lb 13 5 kg each The calculation would be 1400 5 x 220 5 x 30 1400 1100 150 150 Ib Yes you have enough load capacity in your vehicle to transport four friends and your golf bags In metric units the calculation would be 635 kg 5 x 99 kg 5 x 13 5 kg 635 495 67 5 72 5 kg A final example for your vehicle with 1400 lb 635 kg of cargo and luggage capacity You and one of your friends decide to pick up cement from the local home improvement store to finish that patio you have been planning for the past 2 years Measuring the inside of the vehicle with the rear seat folded down you have room for 12 100 Ib 45 kg bags of cement Do you have enough load capacity to transport the cement to your home If you and your friend each weigh 220 Ib 99 kg the calculation would be 1400 2 x 220 12 x 100 1400 440 1200 240 Ib No you do not have enough cargo capacity to carry that much weight In metric units the calculation would be 635 kg 2 x 99 kg 12 x 45 kg 635 198 540 103 kg You will need to reduce the load weig
131. lacement Requirements Your vehicle is equipped with tires designed to provide a safe ride and handling capability Only use replacement tires and wheels that are the same size and type such as P metric versus LT metric or all season versus all terrain as those originally provided by Ford Use of any tire or wheel not recommended by Ford can affect the safety and performance of your vehicle which could result in an increased risk of loss of vehicle control vehicle rollover personal injury and death Additionally the use of non recommended tires and wheels could cause steering suspension axle or transfer case power transfer unit failure If you have questions regarding tire replacement see an authorized dealer Important Remember to replace the wheel valve stems when the road tires are replaced on your vehicle It is recommended that the two front tires or two rear tires generally be replaced as a pair Safety practices Driving habits have a great deal to do with your tire mileage and safety e Observe posted speed limits e Avoid fast starts stops and turns Avoid potholes and objects on the road Do not run over curbs or hit the tire against a curb when parking If your vehicle is stuck in snow mud sand etc do not rapidly spin the tires spinning the tires can tear the tire and cause an explosion A tire can explode in as little as three to five seconds 128 Tires Wheels and Loading Never spin the tires in excess
132. lapsed Drive Time perform the following 1 Press and release RESET in order to start the timer 2 Press and release RESET to pause the timer 3 Press and hold RESET for 2 seconds in order to reset the timer Average speed Select this function from the INFO a a average speed since XXX AVERAGE APH O80000 m 000 0 Blank Display Select this function from the INFO control to turn your message center display OFF 59 Driver Controls System warnings System warnings alert you to possible problems or malfunctions in your vehicle s operating systems In the event of a multiple warning situation the message center will cycle the display to show all warnings by displaying each one for 4 seconds The message center will display the last selected feature if there are no more warning messages This allows you to use the full functionality of the message center after you acknowledge the warning by pressing the RESET control and clearing the warning message Warning messages that have been reset are divided into three categories e They will not disappear until a condition is changed e They will reappear on the display ten minutes from the reset e They will not reappear until an ignition OFF ON cycle has been completed This acts as a reminder that these warning conditions still exist within the vehicle Warning display Driver s door ajar Warning cannot be reset Passenger door ajar Warning returns after 10 minute
133. ler and make sure it is properly attached to your vehicle See your authorized dealer or a reliable trailer dealer if you require assistance Hitches Do not use hitches that clamp onto the vehicle bumper Use a load carrying hitch You must distribute the load in your trailer so that 10 15 of the total weight of the trailer is on the tongue Safety chains Always connect the trailer s safety chains to the frame or hook retainers of the vehicle hitch To connect the trailer s safety chains cross the chains under the trailer tongue and allow slack for turning corners If you use a rental trailer follow the instructions that the rental agency gives to you Do not attach safety chains to the bumper Trailer brakes Electric brakes and manual automatic or surge type trailer brakes are safe if installed properly and adjusted to the manufacturer s specifications The trailer brakes must meet local and Federal regulations Do not connect a trailer s hydraulic brake system directly to your vehicle s brake system Your vehicle may not have enough braking power and your chances of having a collision greatly increase The braking system of the tow vehicle is rated for operation at the GVWR not GCWR 143 Tires Wheels and Loading Trailer lamps Trailer lamps are required on most towed vehicles Make sure all running lights brake lights turn signals and hazard lights are working Do not splice into the vehicle lamp wir
134. level in the fuel tank is at or near empty refer to Fuel gauge in this chapter Speed control if equipped Iluminates when the speed control is engaged Turns off when the speed control system is disengaged Door Trunk ajar if equipped mA Iluminates when the ignition is in 2 the ON position and any door or Vy trunk is open Anti theft system Flashes when AN the Securilock Passive Anti theft System has been activated R a Electronic throttle control Illuminates when the engine has A defaulted to a limp home operation Report the fault to a dealer at the earliest opportunity 13 Instrument Cluster left or right turn signal or the hazard lights are turned on If the indicators stay on or flash faster check for a burned out bulb Daytime running lamps DRL s0 Cif equipped Iluminates when 0o00 D the Daytime running lamps are on 29o Also is an indication that the tail lamps license plate lamps side marker lamps and parking lamps are switched OFF Turn signal Illuminates when the High beams Illuminates when the high beam headlamps are turned on Always remember to turn on your headlamps at dusk or during inclement weather The Daytime Running Lamp DRL system does not activate the tail lamps and generally may not provide adequate lighting during these conditions Failure to activate your headlamps under these conditions may result in a collision Key in ignition warn
135. ling convertible The tether anchors in your vehicle are either located under a cover marked with the child tether anchor symbol shown with title or are under a tag marked with the child tether anchor symbol in the convertible top sling The tether strap anchors in your vehicle are in the following positions shown from top view Attach the tether strap only b to the appropriate tether anchor as shown The tether strap may not work properly if attached somewhere other than the correct y tether anchor 1 Position the child safety seat on the seat cushion 2 Route the child safety seat tether strap over the back of the seat For vehicles with adjustable head restraints route the tether strap under the head restraint and between the head restraint posts otherwise route the tether strap over the top of the seatback 3 Locate the correct anchor for the ea selected seating position as shown N previously 116 Seating and Safety Restraints For Coupe only 4 Open the tether anchor covers aN 5 Clip the tether strap to the anchor as shown For Convertible only The tether anchors on the convertible are located rearward of the seatback in the convertible top sling Note For easier access attach the tether with the convertible top up 117 Seating and Safety Restraints Note The attachments for the convertible boot located on the back of the head restraints are not
136. ly contains more metallic additives than regular fuel We recommend using regular grade fuel In Canada many fuels contain metallic additives but fuels free of such additives may be available check with your local fuel dealer Do not use fuel containing methanol It can damage critical fuel system components Repairs to correct the effects of using a fuel for which your vehicle was not designed may not be covered by your warranty 217 Maintenance and Specifications Octane recommendations Your vehicle is designed to use Regular unleaded gasoline with pump R M 2 octane rating of 87 We do not recommend the use of gasolines labeled as Regular that are sold with octane ratings of 86 or lower in high altitude areas Do not be concerned if your engine sometimes knocks lightly However if it knocks heavily under most driving conditions while you are using fuel with the recommended octane rating see your authorized dealer to prevent any engine damage Fuel quality If you are experiencing starting rough idle or hesitation driveability problems try a different brand of unleaded gasoline Premium unleaded gasoline is not recommended for vehicles designed to use Regular unleaded gasoline because it may cause these problems to become more pronounced If the problems persist see your authorized dealer It should not be necessary to add any aftermarket products to your fuel tank if you continue to use high quali
137. ly urged to buy a reliable tire pressure gauge as automatic service station 124 Tires Wheels and Loading gauges may be inaccurate Ford Motor Company recommends the use of a digital or dial type tire pressure gauge rather than a stick type tire pressure gauge Use the recommended cold inflation pressure for optimum tire performance and wear Under inflation or over inflation may cause uneven treadwear patterns Under inflation is the most common cause of tire failures and may result in severe tire cracking tread separation or blowout with unexpected loss of vehicle control and increased risk of injury Under inflation increases sidewall flexing and rolling resistance resulting in heat buildup and internal damage to the tire It also may result in unnecessary tire stress irregular wear loss of vehicle control and accidents A tire can lose up to half of its air pressure and not appear to be flat Always inflate your tires to the Ford recommended inflation pressure even if it is less than the maximum inflation pressure information found on the tire The Ford recommended tire inflation pressure is found on the Safety Compliance Certification Label or Tire Label which is located on the B Pillar or the edge of the driver s door Failure to follow the tire pressure recommendations can cause uneven treadwear patterns and adversely affect the way your vehicle handles Maximum Permissible Inflation Pressure is the tire manufacturer
138. m is indicated by one or more of the following e The readiness light will either e flash or stay lit e The readiness light will not s illuminate immediately after ignition is turned on e A series of five beeps will be heard The tone pattern will repeat periodically until the problem and or light are repaired If any of these things happen even intermittently have the SRS serviced at an authorized dealer immediately Unless serviced the system may not function properly in the event of a collision Disposal of airbags and airbag equipped vehicles See authorized dealer Airbags MUST BE disposed of by qualified personnel SAFETY RESTRAINTS FOR CHILDREN See the following sections for directions on how to properly use safety restraints for children Also see Airbag supplemental restraint system SRS in this chapter for special instructions about using airbags 107 Seating and Safety Restraints Important child restraint precautions You are required by law to use safety restraints for children in the U S and Canada If small children generally children who are four years old or younger and who weigh 40 1b 18 kg or less ride in your vehicle you must put them in safety seats made especially for children Many states require that children use approved booster seats until they are eight years old Check your local and state or provincial laws for specific requirements regarding the safety of children in your vehicle When possible
139. m the air intake area at the base of the windshield e To improve the A C cool down drive with the windows slightly open for 2 3 minutes after start up or until the vehicle has been aired out For maximum cooling performance in MAX A C mode 1 Move temperature control to the coolest setting 2 Set the fan to the highest speed initially then adjust to maintain comfort For maximum cooling performance in panel or panel floor modes 1 Move temperature control to the coolest setting 2 Select A C and recirculated air AO to provide colder airflow 3 Set the fan to the highest speed initially then adjust to maintain comfort To aid in side window defogging demisting in cold weather 1 Select 4 2 Select A C 3 Adjust the temperature control to maintain comfort 4 Set the fan speed to the highest setting 5 Direct the outer instrument panel vents towards the side windows 6 To increase airflow to the outer instrument panel vents close the vents located in the middle of the instrument panel Do not place objects on top of the instrument panel as these objects may become projectiles in a collision or sudden stop 31 Climate Controls REAR WINDOW DEFROSTER Rj Ensure that the ignition is in the 3 ON position Press the control to clear the rear window of thin ice and fog The LED will illuminate The rear window defroster turns off automatically after 10 minutes or when the ignition is turned to the
140. mall for lap shoulder belts to fit properly which could increase the risk of serious injury in a crash To improve the fit of both the lap and shoulder belt on children who have outgrown child safety seats Ford Motor Company recommends use of a belt positioning booster Booster seats position a child so that safety belts fit better They lift the child up so that the lap belt rests low across the hips and the knees bend comfortably Booster seats may also make the shoulder belt fit better and more comfortably Try to keep the belt near the middle of the shoulder When children should use booster seats Children need to use booster seats from the time they outgrow the toddler seat until they are big enough for the vehicle seat and lap shoulder belt to fit properly Generally this is when they weigh about 80 Ib 86 kg about 8 to 12 years old Booster seats should be used until you can answer YES to ALL of these questions e Can the child sit all the way back against the vehicle seat back with knees bent comfortably at the edge of the seat without slouching e Does the lap belt rest low across the hips Is the shoulder belt centered on the shoulder and chest e Can the child stay seated like this for the whole trip 109 Seating and Safety Restraints Types of booster seats There are two types of belt positioning booster seats e Those that are backless If your backless booster seat has a removable shield remove the s
141. matic locking mode 7 Pull the lap belt portion across the child seat toward the buckle and pull up on the shoulder belt while pushing down with your knee on the child seat 8 Allow the safety belt to retract to remove any slack in the belt 9 Before placing the child in the seat forcibly move the seat forward and back to make sure the seat is securely held in place To check this grab the seat at the belt path and attempt to move it side to side and forward There should be no more than one inch of movement for proper installation 10 Try to pull the belt out of the retractor to make sure the retractor is in the automatic locking mode you should not be able to pull more belt out If the retractor is not locked unbuckle the belt and repeat Steps 2 through 9 Check to make sure the child seat is properly secured before each use 115 Seating and Safety Restraints Attaching child safety seats with tether straps i Most new forward facing child safety seats include a tether strap which goes over the back of the seat and hooks to an anchoring point Tether straps are available as an accessory for many older safety seats Contact the manufacturer of your child seat for information about ordering a tether strap The rear seats of your vehicle are equipped with built in tether strap anchors located behind the seats and below the rear window behind the speakers coupe or rearward of the seatback in the convertible top s
142. may be disabled and may need to be serviced Even when the ABS is disabled normal braking is still effective If 1 P your BRAKE warning lamp illuminates with the parking brake B RAKE released have your brake system serviced immediately Using ABS When hard braking is required apply continuous force on the brake pedal do not pump the brake pedal since this will reduce the effectiveness of the ABS and will increase your vehicle s stopping distance The ABS will be activated immediately allowing you to retain full steering control during hard braking and on slippery surfaces However the ABS does not decrease stopping distance Parking brake To set the parking brake 1 pull the parking brake handle up as far as possible The BRAKE warning lamp will illuminate and will remain illuminated until the parking brake is released B RAKE To release press and hold the button 2 pull the handle up slightly then push the handle down 151 Driving Always set the parking brake fully and make sure that the gearshift is securely latched in P Park automatic transmission or in 1 First manual transmission If the parking brake is fully released but the brake warning lamp remains illuminated the brakes may not be working properly See your authorized dealer as soon as possible TRACTION CONTROL IF EQUIPPED Your vehicle may be equipped with a Traction Control system This system helps yo
143. mperature Y indicator will illuminate e The Service engine soon indicator light will illuminate If the engine reaches a preset over temperature condition the engine will automatically switch to alternating cylinder operation Each disabled cylinder acts as an air pump and cools the engine When this occurs the vehicle will still operate However e The engine power will be limited e The air conditioning system will be disabled Continued operation will increase the engine temperature e The engine will completely shut down e Steering and braking effort will increase Once the engine temperature cools the engine can be re started Take your vehicle to an authorized dealer as soon as possible to minimize engine damage When fail safe mode is activated You have limited engine power when in the fail safe mode so drive the vehicle with caution The vehicle will not be able to maintain high speed operation and the engine will run rough Remember that the engine is capable of completely shutting down automatically to prevent engine damage therefore 1 Pull off the road as soon as safely possible and turn off the engine 2 Arrange for the vehicle to be taken to an authorized dealer 3 If this is not possible wait a short period for the engine to cool 213 Maintenance and Specifications 4 Check the coolant level and replenish if low Never remove the coolant reservoir cap while the engine is running or hot 5 Res
144. n components or damage the transmission Make sure the floor mat is properly positioned so it doesn t interfere with the full extension of the clutch pedal Do not drive with your foot resting on the clutch pedal or use the clutch pedal to hold your vehicle at a standstill while waiting on a hill These actions will reduce the life of the clutch 159 Driving Recommended shift speeds Do not downshift into 1 First when your vehicle is moving faster than 15 mph 24 km h This will damage the clutch Upshift according to the following chart Upshifts when accelerating recommended for best fuel economy Shift from Reverse 1 Make sure that your vehicle is at a complete stop before you shift into R Reverse Failure to do so may damage the transmission 2 Move the gearshift lever into the neutral position and wait at least three seconds before shifting into R Reverse e The gearshift lever can only be moved into R Reverse by moving it from left of 3 Third and 4 Fourth before shifting into R Reverse This is a lockout feature that protects the transmission from accidentally being shifted into R Reverse from 5 Overdrive Parking your vehicle 1 Apply the brake and shift into the neutral position 2 Fully apply the parking brake then shift into 1 First 3 Turn the ignition off Do not park your vehicle in Neutral it may move unexpectedly and injure someone Use 1 First gear and set the parking b
145. n deactivating activating one seating position do not buckle the other position as this will terminate the process Read Steps 1 4 thoroughly before proceeding with the deactivation activation programming procedure Note The driver and front passenger BeltMinder features must be disabled enabled separately Both cannot be disable enabled during the same key cycle 95 Seating and Safety Restraints The driver and front passenger BeltMinder features can be deactivated activated by performing the following procedure Before following the procedure make sure that e The parking brake is set e The gearshift is in P Park automatic transmission e The gearshift is in N Neutral Manual transmission e The ignition switch is in the OFF position e The driver and front passenger safety belts are unbuckled To reduce the risk of injury do not deactivate activate the BeltMinder feature while driving the vehicle 1 Turn the ignition switch to the RUN or ON position DO NOT START THE ENGINE 2 Wait until the safety belt warning light turns off Approximately 1 minute e Step 3 must be completed within 50 seconds after the safety belt warning light turns off 3 For the seating position being disabled at a moderate speed buckle then unbuckle the safety belt 9 times ending in the unbuckled state Step 3 must be completed within 50 seconds after the safety belt warning light turns off e After Step 3 the rest
146. n film attached and CDs with homemade paper adhesive labels should not be inserted into the CD player The label may peel and cause the CD to become jammed It is recommended that homemade CDs be identified with permanent felt tip marker rather than adhesive labels Ball point pens may damage CDs Please contact your authorized dealer for further information Audio system warranty and service Refer to the Warranty Guide for audio system warranty information If service is necessary see your dealer or qualified technician 29 Climate Controls MANUAL HEATING AND AIR CONDITIONING SYSTEM 1 Temperature selection Controls the temperature of the airflow in the vehicle 2 Mode selections Controls the location of the airflow in the vehicle See the following for a brief description of each selection MAX A C Distributes recirculated air through the instrument panel vents to cool the vehicle This re cooling of the interior air is more economical and efficient Recirculated air may also help reduce undesirable odors from e e e entering the vehicle R 74 Distributes air through the 5 4 3 instrument panel vents lt 7 Distributes air through the instrument panel vents and the floor vents O OFF Outside air is shut out and the climate system is turned off A Distributes air through the floor vents T Distributes air through the windshield defroster vents and floor vents QW Distribute
147. n in separate publications This Owner s Guide describes every option and model variant available and therefore some of the items covered may not apply to your particular vehicle Furthermore due to printing cycles it may describe options before they are generally available Remember to pass on this Owner s Guide when reselling the vehicle It is an integral part of the vehicle Fuel pump shut off switch In the event of an accident the safety switch will automatically cut off the fuel supply to the engine The switch can also be activated through sudden vibration e g collision when parking To reset the switch refer to the Fuel pump shut off switch in the Roadside Emergencies chapter Introduction SAFETY AND ENVIRONMENT PROTECTION Warning symbols in this guide How can you reduce the risk of personal injury to yourself or others In this guide answers to such questions are contained in comments highlighted by the warning triangle symbol These comments should be read and observed Warning symbols on your vehicle When you see this symbol it is imperative that you consult the relevant section of this guide before L i touching or attempting adjustment of any kind Protecting the environment We must all play our part in protecting the environment Correct vehicle usage and the authorized disposal of waste cleaning and lubrication materials are significant steps towards this aim Information in this respect is h
148. n the event of a sudden stop or collision 81 Seating and Safety Restraints SAFETY RESTRAINTS Personal Safety System The Personal Safety System provides an improved overall level of frontal crash protection to front seat occupants and is designed to help further reduce the risk of airbag related injuries The system is able to analyze different occupant conditions and crash severity before activating the appropriate safety devices to help better protect a range of occupants in a variety of frontal crash situations Your vehicle s Personal Safety System consists of e Driver and passenger dual stage airbag supplemental restraints e Driver and front passenger side airbags if equipped e Front safety belts with pretensioners energy management retractors and safety belt usage sensors e Driver s seat position sensor e Front crash severity sensor e Front passenger sensing system e Passenger airbag off or pass airbag off indicator lamp e Restraints Control Module RCM with impact and safing sensors e Restraint system warning light and back up tone e The electrical wiring for the airbags crash sensor s safety belt pretensioners front safety belt usage sensors driver seat position sensor front passenger sensing system and indicator lights How does the Personal Safety System work The Personal Safety System can adapt the deployment strategy of your vehicle s safety devices according
149. n the vehicle by hooking the boot retaining clips on the back panel 2 Install the boot on the right side tucking in the front part of the boot in the quarter panel and hooking the retaining clip on the side 3 Install the boot on the left side tucking in the front part of the boot in the quarter panel and hooking the retaining clip on the side 4 Tuck the boot corners behind the shoulder belts 5 Secure the boot straps on the rear seat hooks behind the rear seat Note Improper installation can result in loss and or damage of the boot while driving Always secure the retaining clips and boot straps on the vehicle or the boot may come loose while driving To remove unhook the boot straps from the rear seat hooks and push the boot down slightly unhooking the boot retaining clips from the vehicle and lift off 51 Driver Controls Storing the boot 7x C E 1 Position the boot right side up and fold each side of the boot inward 2 Turn the boot upside down and fold the left side of the boot inward A v 3 Fold the right side inward and secure the boot with the strap Stow the boot in the trunk Raising the convertible top The convertible top will not operate unless the vehicle is traveling under 3 1 mph 5 km h 52 Driver Controls To raise the convertible top 1 Bring the vehicle to a complete stop Key must be in the ON position It is recommended that the vehicle s engine is running when rais
150. nd Safety Restraints This mode should be used any time a child safety seat is installed in a passenger front or outboard rear seating position Children 12 years old and under should be properly restrained in the rear seat whenever possible Refer to Safety restraints for children or Safety seats for children later in this chapter How to use the automatic locking mode e Buckle the combination lap and shoulder belt e Grasp the shoulder portion and pull downward until the entire belt is pulled out e Allow the belt to retract As the belt retracts you will hear a clicking sound This indicates the safety belt is now in the automatic locking mode How to disengage the automatic locking mode Ford Motor Company recommends that all safety belt assemblies and attaching hardware should be inspected by an authorized dealer after any collision Safety belt assemblies not in use during a collision should also be inspected and replaced if either damage or improper operation is noted Disconnect the combination lap shoulder belt and allow it to retract completely to disengage the automatic locking mode and activate the vehicle sensitive emergency locking mode 89 Seating and Safety Restraints After any vehicle collision the front passenger and rear outboard seat belt systems must be checked by an authorized dealer to verify that the automatic locking retractor feature for child seats is still functioning properly In addi
151. nel and inside the center console storage bin Do not use the power point for operating the cigarette lighter element if equipped To prevent the fuse from being blown do not use the power point s over the vehicle capacity of 12 VDC 180W To prevent the battery from being discharged do not use the power point longer than necessary when the engine is not running Always keep the power point caps closed when not being used 43 Driver Controls Cigarette Cigar lighter if equipped Do not plug optional electrical accessories into the cigarette lighter socket Do not hold the lighter in with your hand while it is heating this will damage the lighter element and socket The lighter will be released from its heating position when it is ready to be used Improper use of the lighter can cause damage not covered by your warranty CENTER CONSOLE Your vehicle is equipped with a variety of console features These include e Dual cupholders e Auxiliary power point in bin e Coin holder slots in bin Use only soft cups in the cupholder Hard objects can injure you in a collision POWER WINDOWS Do not leave children unattended in the vehicle and do not let children play with the power windows They may seriously injure themselves When closing the power windows you should verify they are free of obstructions and ensure that children and or pets are not in the proximity of the window openings Press
152. neseccece 230 choosing the right fuel 217 comparisons with EPA fuel economy estimates 222 detergent in fuel 0 218 filling your vehicle with PUES sirovina 214 216 219 filter specifications 219 228 fuel pump shut off switch 164 improving fuel economy 219 octane rating eee 218 234 guality errre a 218 running out of fuel 000 0000 218 safety information relating to automotive fuels 214 Fuel pump shut off switch 164 EUSES veuan ern 164 165 G Gas cap see Fuel cap 216 Gas mileage see Fuel economy 00008 219 GIURE eiiie o e Ra ti 15 H Hazard flashers cccccceeeeeees 163 Head restraints ccee eee 76 Headlamps ccccccceseceeesseeeees 33 CUTTING Seene enta eitea eE 34 bulb specifications 00 37 daytime running lights 33 HASH GO PASS icten 33 high DEAT ssccesscaessctacns cesvecneigonss 33 replacing bulbs crga 37 turning on and off essesi 33 Index Heating heating and air conditioning SYSTEMA cvesse cs cansdvensees rrin siea HOOG Seririt 197 I ISNI ON seisoen 146 234 Infant seats see Safety seats oo 112 Inspection maintenance I M LESUN O re ronka N 224 Instrument panel Cleaning sissy 193 LEELEE EOE E seve 10 lighting up panel and MMGOTIOL peeoreracn iaa EAR 34 J JACK o iissvedisseivcsassisievtisisieeaecseaes 171 POSHIONING sv sircasvsssevavecsarneeds seats 17
153. ns Care should be taken to avoid inhaling excess fumes The flow of fuel through a fuel pump nozzle can produce static electricity which can cause a fire if fuel is pumped into an ungrounded fuel container 215 Maintenance and Specifications Refueling Fuel vapor burns violently and a fuel fire can cause severe injuries To help avoid injuries to you and others e Read and follow all the instructions on the pump island e Turn off your engine when you are refueling e Do not smoke if you are near fuel or refueling your vehicle e Keep sparks flames and smoking materials away from fuel e Stay outside your vehicle and do not leave the fuel pump unattended when refueling your vehicle this is against the law in some places e Keep children away from the fuel pump never let children pump fuel Use the following guidelines to avoid static build up when filling an ungrounded fuel container e Place approved fuel container on the ground e DO NOT fill a fuel container while it is in the vehicle including the cargo area e Keep the fuel pump nozzle in contact with the fuel container while filling e DO NOT use a device that would hold the fuel pump handle in the fill position Fuel Filler Cap Your fuel tank filler cap has an indexed design with a 1 4 turn on off feature When fueling your vehicle 1 Turn the engine off 2 Carefully turn the filler cap counterclockwise until it spins off the filler pipe 3 Re
154. ns or concerns or are unsatisfied with the service you are receiving follow these steps 1 Contact your Sales Representative or Service Advisor at your selling servicing authorized dealer 2 If your inquiry or concern remains unresolved contact the Sales Manager Service Manager or Customer Relations Manager 3 If you require assistance or clarification on Ford Motor Company policies or procedures please contact the Ford Customer Relationship Center at 1 800 392 3673 FORD Away from home If you own a Ford or Mercury vehicle and are away from home when your vehicle needs service or if you need more help than the authorized dealer could provide after following the steps described above contact the Ford Customer Relationship Center to find an authorized dealer to help you In the United States Ford Motor Company Customer Relationship Center P O Box 6248 Dearborn MI 48121 1 800 392 3673 FORD TDD for the hearing impaired 1 800 232 5952 www customersaskford com In Canada Customer Relationship Centre 182 Customer Assistance Ford Motor Company of Canada Limited P O Box 2000 Oakville Ontario L6J 5E4 1 800 565 3673 FORD www ford ca If you own a Lincoln vehicle and are away from home when your vehicle needs service or if you need more help than the authorized dealer could provide after following the steps described above contact the Ford Customer Relationship Center to find an authorized deale
155. nt amplifier Shaker 500 Engine 3 169 Roadside Emergencies Fuse Relay Fuse Amp Power Distribution Box Horn o SS a a O 5 Notas i a po aeee 30A SJB 5 Instrument panel fuse box Notused S O panel box box Power point 2 Console ABS 2 30A SJB 4 Instrument panel fuse box Cartridge Fuses Mini Fuses Auxiliary relay There is a relay located on the accelerator pedal assembly for the PCM delay Note Only on manual transmission applications 170 Roadside Emergencies CHANGING THE TIRES If you get a flat tire while driving e do not brake heavily e gradually decrease the vehicle s speed e hold the steering wheel firmly e slowly move to a safe place on the side of the road Your vehicle may be equipped with a conventional spare tire that is different in one or more of the following type brand size speed rating and tread design If this is the case this dissimilar spare tire is still rated for your vehicle loads GAWR and GVWR A The use of tire sealants may damage your tires Dissimilar spare tire wheel information Failure to follow these guidelines could result in an increased risk of loss of vehicle control injury or death If you have a dissimilar spare tire wheel then it is intended for temporary use only This means that if you need to use it you should replace it as soon as possible with a road tire wheel that is the same size and type as the road
156. nual transmission 1 Set the parking brake depress the clutch and place the gearshift in 1 First 2 Turn off the engine and remove the key 3 Block the wheels 196 Maintenance and Specifications Working with the engine on e Automatic transmission 1 Set the parking brake and shift to P Park 2 Block the wheels e Manual transmission 1 Set the parking brake depress the clutch and place the gearshift in N Neutral 2 Block the wheels Note Do not start your engine with the air cleaner removed and do not remove it while the engine is running OPENING THE HOOD ome 1 Inside the vehicle pull the hood release handle located on the driver s side kick panel 2 Go to the front of the vehicle and release the auxiliary latch that is located under the front center of the hood 3 Lift the hood and secure it with the prop rod 197 Maintenance and Specifications IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 4 0L SOHC V6 engine lt ae es a NE Battery Engine oil filler cap Engine oil dipstick Brake fluid reservoir Air filter assembly Power steering fluid reservoir Engine coolant reservoir Windshield washer fluid reservoir woOoNanR WN HE Power distribution box 198 Maintenance and Specifications 4 6L 3V SOHC V8 engine Foe VE Engine oil dipstick
157. nuously bounce back Accessory delay With accessory delay the window switches and radio may be used for up to ten minutes after the ignition switch is turned to the OFF position or until any door or trunk is opened Bounce Back Front windows only When an obstacle has been detected in the window opening as the window is moving upward the window will automatically move down and stop at a prescribed position 45 Driver Controls Bounce Back Override Front windows only To override Bounce Back within 2 seconds after reaching Bounce Back position if the switch is moved from the Neutral to the Express Up position the window will travel up with no bounce back protection If the switch is released before the window reaches fully closed position the window will stop For example Bounce Back Override can be used to overcome the resistance of ice on the window or seals Short drop glass Front windows only In order to improve door efforts and sealing your vehicle is equipped with short drop glass This feature lowers the glass when either door is opened The glass returns to its closed position when the door is closed Proper operation of the short drop glass requires that the windows be calibrated Though your windows will have been calibrated before your vehicle is delivered to you it is possible for the windows to lose calibration If a window loses its calibration your short drop feature will lower the window but will not
158. oad the CD If the selected slot already contains a CD the display will read SLOT FULL Press and hold to autoload up to 6 CDs Load CDs one at a time when the radio prompts to load a CD 19 CD eject Press to begin the CD eject sequence When the radio prompts to select a CD use the presets to select the desired CD to eject Press and hold to auto eject all CDs present in the system If there is no CD present the display will read NO CD 20 CD slot Insert one CD ata m i time label side up when the system prompts to load a CD MP3 track and folder structure Your MP3 system recognizes MP3 individual tracks and a folder structure as follows e There are two different modes for MP3 disc playback MP3 track mode system default and MP3 folder mode e MP3 track mode ignores any folder structure present on the MP3 disc The player sequentially numbers each MP3 track on the disc denoted by the mp3 file extension from T001 to T255 e MP3 folder mode represents a folder structure consisting of one level of folders The CD player sequentially numbers all MP3 tracks on the disc denoted by the mp3 extension and all folders containing MP3 files from 01 01 to 99 99 The first two digits denote the folder number and the last two digits denote the track number within that folder Creating discs with only one level of folders will help with navigation through the disc files 27 Entertainment Systems GENERAL AUDIO INFOR
159. oaded Excessive speed underinflation or excessive loading either separately or in combination can cause heat buildup and possible tire failure TIRES Tires are designed to give many thousands of miles of service but they must be maintained in order to get the maximum benefit from them Glossary of tire terminology e Tire label A label showing the OE Original Equipment tire sizes recommended inflation pressure and the maximum weight the vehicle can carry e Tire Identification Number TIN A number on the sidewall of each tire providing information about the tire brand and manufacturing plant tire size and date of manufacture Also referred to as DOT code e Inflation pressure A measure of the amount of air in a tire e Standard load A class of P metric or Metric tires designed to carry a maximum load at 35 psi 87 psi 2 5 bar for Metric tires Increasing the inflation pressure beyond this pressure will not increase the tire s load carrying capability e Extra load A class of P metric or Metric tires designed to carry a heavier maximum load at 41 psi 48 psi 2 9 bar for Metric tires 123 Tires Wheels and Loading Increasing the inflation pressure beyond this pressure will not increase the tire s load carrying capability e kPa Kilopascal a metric unit of air pressure e PSI Pounds per square inch a standard unit of air pressure e Cold inflation pressure The tire pressure when the vehicle has be
160. odically An unbalanced tire and wheel assembly may result in irregular tire wear Tire rotation Rotating your tires at the recommended interval as indicated in the scheduled maintenance information that comes with your vehicle will help your tires wear more evenly providing better tire performance and longer tire life Unless otherwise specified rotate the tires approximately every 5 000 miles 8 000 km 129 Tires Wheels and Loading e Rear Wheel Drive RWD vehicles Four Wheel Drive 4WD All Wheel Drive AWD vehicles front tires at top of diagram NNVANNAA SAAR AAS eo YVNVANNNA AN VANAAYN Sometimes irregular tire wear can be corrected by rotating the tires Note If your tires show uneven wear ask an authorized dealer to check for and correct any wheel misalignment tire imbalance or mechanical problem involved before tire rotation Note Your vehicle may be equipped with a dissimilar spare tire wheel A dissimilar spare tire wheel is defined as a spare tire and or wheel that is different in brand size or appearance from the road tires and wheels If you have a dissimilar spare tire wheel it is intended for temporary use only and should not be used in a tire rotation Note After having your tires rotated inflation pressure must be checked and adjusted to the vehicle requirements INFORMATION CONTAINED ON THE TIRE SIDEWALL Both U S and Canada Federal regulations require tire manufacturers to place stan
161. of the 35 mph 55 km h point indicated on the speedometer Highway hazards No matter how carefully you drive there s always the possibility that you may eventually have a flat tire on the highway Drive slowly to the closest safe area out of traffic This may further damage the flat tire but your safety is more important If you feel a sudden vibration or ride disturbance while driving or you suspect your tire or vehicle has been damaged immediately reduce your speed Drive with caution until you can safely pull off the road Stop and inspect the tires for damage If a tire is under inflated or damaged deflate it remove wheel and replace it with your spare tire and wheel If you cannot detect a cause have the vehicle towed to the nearest repair facility or tire dealer to have the vehicle inspected Tire and wheel alignment A bad jolt from hitting a curb or pothole can cause the front end of your vehicle to become misaligned or cause damage to your tires If your vehicle seems to pull to one side when you re driving the wheels may be out of alignment Have an authorized dealer check the wheel alignment periodically Wheel misalignment in the front or the rear can cause uneven and rapid treadwear of your tires and should be corrected by an authorized dealer Front wheel drive FWD vehicles and those with an independent rear suspension if equipped may require alignment of all four wheels The tires should also be balanced peri
162. ommended if you live in a region where temperatures reach 10 F 23 C or below For best results plug the heater in at least three hours before starting the vehicle The heater can be plugged in the night before starting the vehicle To reduce the risk of electrical shock do not use your heater with ungrounded electrical systems or two pronged cheater adapters BRAKES Occasional brake noise is normal If a metal to metal continuous grinding or continuous squeal sound is present the brake linings may be worn out and should be inspected by an authorized dealer If the vehicle has continuous vibration or shudder in the steering wheel while braking the vehicle should be inspected by an authorized dealer Refer to Brake system warning light in the Instrument Cluster chapter for information on the brake system warning light B RAKE Four wheel anti lock brake system ABS if equipped Your vehicle may be equipped with an Anti lock Braking System ABS This system helps you maintain steering control during emergency stops by keeping the brakes from locking Noise from the ABS pump motor and brake pedal pulsation may be observed during ABS braking any pulsation or mechanical noise you may feel or hear is normal 150 Driving ABS warning lamp The ABS lamp in the instrument cluster momentarily illuminates when the ignition is turned on If the light does not illuminate during start up remains on or flashes the ABS
163. one time In the case of 1 or 2 above the consumer must also notify the manufacturer of the need for the repair of the nonconformity at the following address Ford Motor Company 16800 Executive Plaza Drive Mail Drop 3NE B Dearborn MI 48126 THE BETTER BUSINESS BUREAU BBB AUTO LINE PROGRAM U S ONLY Your satisfaction is important to Ford Motor Company and to your dealer Experience has shown that our customers have been very successful in 184 Customer Assistance achieving satisfaction by following the three step procedure outlined on the front page of the Warranty Guide However if your warranty concern has not been resolved using the three step procedure you may be eligible to participate in the BBB AUTO LINE program The BBB AUTO LINE program consists of two parts mediation and arbitration Initially the BBB will try to resolve your question or concern through mediation Mediation is a process through which a representative of the BBB will contact the parties and explore options for settlement of your claim If mediation is not successful customers with eligible claims may participate in the BBB AUTO LINE arbitration process An arbitration hearing will be scheduled so that you can present your case in an informal setting before an impartial person The arbitrator will consider the testimony provided and make a decision after the hearing You are not bound by the decision but may choose to accept it If you choose to
164. ons on specified government test surfaces of asphalt and concrete A tire marked C may have poor traction performance e Temperature The temperature grades are A the highest B and C representing the tire s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel 13 Maximum Permissible Inflation Pressure Indicates the tire manufacturers maximum permissible pressure and or the pressure at which the maximum load can be carried by the tire This pressure is normally higher than the manufacturer s recommended cold inflation pressure which can be found on the Safety Compliance Certification Label or Tire Label which is located on the B Pillar or the edge of the driver s door The cold inflation pressure should never be set lower than the recommended pressure on the vehicle label The tire suppliers may have additional markings notes or warnings such as standard load radial tubeless etc 133 Tires Wheels and Loading Additional information contained on the tire sidewall for LT type tires LT type tires have some additional information beyond those of P type tires these differences are described below 1 LT Indicates a tire designated by the Tire and Rim Association T amp RA that is intended for service on light trucks 2 Load Range Load Inflation Limits Indicates the tire s load carrying cap
165. operly substances on the vehicle s glass or the wiper blades may be the cause These may include hot wax treatments used by commercial car washes water repellant coatings tree sap or other organic contamination these contaminants may cause squeaking or chatter noise from the blades and streaking and smearing of the windshield To clean these items follow these tips e The windshield rear windows and side windows may be cleaned with a non abrasive cleaner such as Motorcraft Ultra Clear Spray Glass Cleaner ZC 23 available from your authorized dealer e The wiper blades can be cleaned with isopropyl rubbing alcohol or Motorcraft Premium Windshield Washer Concentrate ZC 32 A available from your authorized dealer This washer fluid contains special solution in addition to alcohol which helps to remove the hot wax deposited on the wiper blade and windshield from automated car wash facilities Be sure to replace wiper blades when they appear worn or do not function properly e Do not use abrasives as they may cause scratches e Do not use fuel kerosene or paint thinner to clean any parts CONVERTIBLE TOP AND PADDED MOLDING Wash with Motorcraft Triple Clean ZC 13 which is available from your authorized dealer e Do not use stiff bristle brushes or abrasive materials or cleaners e Hot waxes applied by commercial car washes can affect the cleanability of vinyl material e Using high water pressure or wand type car washes
166. otor Oil US Motorcraft SAE 5W 30 Super Premium Motor Oil Canada Motorcraft Premium Gold Engine Coolant yellow colored Motorcraft MERCON ATF Motorcraft SAE 75W 140 High Performance Rear Axle Lubricant 230 4 6L V8 engine L 4 0L V6 engine Between MIN and MAX lines on reservoir 6 0 quarts 5 7 5 0 quarts 4 7L 4 0L V6 engine 12 5 quarts 11 8L 4 6L V8 engine 13 6 quarts 12 9L Fill to between MIN and MAX lines on reservoir 7 5 inch axle 3 25 pints 1 5L V6 8 8 inch axle 4 25 pints 2 0L V8 16 0 gallons 60 6L Maintenance and Specifications Fluid Ford Part Application Capacity Name Manual Motorcraft 4 0L V6 engine 2 75 quarts Transmission MERCON ATF 2 6L fluid 4 6L V8 engine 3 2 quarts 3 0L Windshield Motorcraft All washer fluid Premium Windshield Washer Concentrate Tadd the coolant type originally equipped in your vehicle Automatic Motorcraft All 11 9 quarts Transmission MERCON V 11 21 fluid ATF Rear axle lubricants do not need to be checked or changed unless a leak is suspected service is required or the axle assembly has been submerged in water The axle lubricant should be changed any time the rear axle has been submerged in water Fill 1 4 inch to 9 16 inch 6 mm to 14 mm below bottom of fill hole Add 4 oz 118 ml of Additive Friction Modifier XL 3 or equivalent meeting Ford specification EST M2C118 A for complete
167. out keeping your foot on the accelerator pedal Speed control does not work at speeds below 30 mph 48 km h Do not use the speed control in heavy traffic or on roads that are winding slippery or unpaved Setting speed control The controls for using your speed C control are located on the steering wheel for your convenience 1 Press the ON control and release it 2 Accelerate to the desired speed 3 Press the SET control and release it O 4 Take your foot off the accelerator pedal 5 The indicator light O on the instrument cluster will turn on Note e Vehicle speed may vary momentarily when driving up and down a steep hill e If the vehicle speed increases above the set speed on a downhill you may want to apply the brakes to reduce the speed 47 Driver Controls e If the vehicle speed decreases more than 10 mph 16 km h below your set speed on an uphill your speed control will disengage e If the vehicle speed decreases to 30 mph 48 km h or less your speed control will disengage Disengaging speed control To disengage the speed control e Depress the brake pedal or clutch pedal if equipped Disengaging the speed control will not erase previous set speed Q gt Resuming a set speed Press the RES resume control and release it This will automatically return the vehicle to the previously set speed The RES control will not work if the vehicle spe
168. outboard side of the driver s seat 79 Seating and Safety Restraints Move the switch in the direction of the arrows to raise or lower the front portion of the seat cushion Move the switch in the direction of the arrows to raise or lower the rear 4 portion of the seat cushion Press the switch in the direction of the arrows to move the seat forward backward up or down Rear seat entry exit Use the seatback release to fold the back of the front seat forward for rear seat access This release handle is located on the upper back of the front seat The seatback locks automatically when returned to the normal position 80 Seating and Safety Restraints Use the recliner handle to return the seatback to the desired position REAR SEATS 2nd seat split folding rear seat One or both rear seatbacks coupe only can be folded down to provide additional cargo space To lower the seatback s from inside the vehicle pull strap to release seat back and then fold seatback down When raising the seatback s make sure you hear the seat latch into place Pull on the seatback to ensure that it has latched Before returning the seatback to its original position make sure that cargo or any objects are not trapped behind the seatback After returning the seatback to its original position pull on the seatback to ensure that it has fully latched An unlatched seat may become dangerous i
169. ows for first gear when the vehicle reaches slower speeds Forced downshifts e Allowed in Overdrive or Drive e Depress the accelerator to the floor e Allows transmission to select an appropriate gear If your vehicle gets stuck in mud or snow If your vehicle gets stuck in mud or snow it may be rocked out by shifting between forward and reverse gears stopping between shifts in a steady pattern Press lightly on the accelerator in each gear 158 Driving Do not rock the vehicle if the engine is not at normal operating temperature or damage to the transmission may occur Do not rock the vehicle for more than a minute or damage to the transmission and tires may occur or the engine may overheat MANUAL TRANSMISSION OPERATION IF EQUIPPED Using the clutch The manual transmission has a starter interlock that prevents cranking the engine unless the clutch pedal is fully depressed To start the vehicle 1 Make sure the parking brake is fully set 2 Press the clutch pedal to the floor then put the gearshift lever in the neutral position 3 Start the engine then press the brake pedal and release the parking brake 4 Move the gearshift lever to 1st gear then slowly release the clutch pedal while slowly pressing on the accelerator During each shift the clutch pedal must be fully depressed to the floor Failure to fully depress the clutch pedal to the floor may cause increased shift efforts prematurely wear transmissio
170. pliance Certification Label axle weight rating limits could result in substandard vehicle handling or performance engine transmission and or structural damage serious damage to the vehicle loss of control and personal injury Note For trailer towing information refer to Trailer towing found in this chapter or the RV and Trailer Towing Guide provided by your authorized dealer GVW Gross Vehicle Weight is the Vehicle Curb Weight cargo passengers 139 Tires Wheels and Loading GVWR Gross Vehicle Weight Rating is the maximum Sample Safety Compliance Certification Label Refer to actual label on your vehicle allowable weight of the fully loaded Front GAWR GVWR Rear GAWR vehicle Gncluding all options MFD BY FORD MOTOR CO IN U S A equipment passengers and cargo DATE 0695 GVWR 6250 LB 2834 KG The GVWR is shown on the KG y RE RTB wry Safety Compliance Certification BUIS M S MS Label located on the B Pillar or THS VEHICLE CONFORMS TO AL APPLICABLE FEDERAL MOTOR the edge of the driver s door VEHICLE SAFETY STANDARDS IN EFFECT ON THE DATE OF The GVW must never exceed the XX Pae s om eR GVWR iti on aati EXT PNT XXXXXX XXXXXX Dsi wo TYPE Gvw BoDY TRANS T ae T TAPE i 155 REM E Exceeding the Safety Compliance Certification Label vehicle weight rating limits could result in substandard vehicle handling or performance engine transmission and or structural damage serious d
171. present on the mounting surfaces of the wheel or the surface of the wheel hub brake drum or brake disc that contacts the wheel Ensure that any fasteners that attach the rotor to the hub are secured so they do not interfere with the mounting surfaces of the wheel Installing wheels without correct metal to metal contact at the wheel mounting surfaces can cause the wheel nuts to loosen and the wheel to come off while the vehicle is in motion resulting in loss of control JUMP STARTING The gases around the battery can explode if exposed to flames sparks or lit cigarettes An explosion could result in injury or vehicle damage Batteries contain sulfuric acid which can burn skin eyes and clothing if contacted Do not attempt to push start your vehicle Automatic transmissions do not have push start capability doing so may damage the catalytic converter Preparing your vehicle When the battery is disconnected or a new battery is installed the transmission must relearn its shift strategy As a result the transmission may have firm and or soft shifts This operation is considered normal and will not affect function or durability of the transmission Over time the adaptive learning process will fully update transmission operation 176 Roadside Emergencies 1 Use only a 12 volt supply to start your vehicle 2 Do not disconnect the battery of the disabled vehicle as this could damage the vehicle s electrical system 3 Par
172. r s door vehicles exported outside the US and Canada may not have a Tire Label Look for THE COMBINED WEIGHT OF OCCUPANTS AND CARGO SHOULD NEVER EXCEED XXX kg OR XXX Ib for maximum payload The payload listed on the Tire Label is the maximum payload for the vehicle as built by the assembly plant If any aftermarket or authorized dealer installed equipment has been installed on the vehicle the weight of the equipment must be subtracted from the payload listed on the Tire Label in order to determine the new payload The appropriate loading capacity of your vehicle can be limited either by volume capacity how much space is available or by payload capacity how much weight the vehicle should carry Once you have reached the maximum payload of your vehicle do not add more cargo even if there is space available Overloading or improperly loading your vehicle can contribute to loss of vehicle control and vehicle rollover 137 Tires Wheels and Loading Example only TIRE AND LOAD INFORMATION SEE OWNERS MANUAL FOR ADDITIONAL INFORMATION The combined weight of occupants and cargo should never exceed XXX kg or XXX Ibs SEATING CAPACITY TOTAL 5 FRONT 2 ORIGINAL TIRE SIZE COLD TIRE INFLATION PRESSURE FRONT P195 70R14 FRONT 200KPA 29PS REAR P195 70R14 REAR 200KPA 29PSI SPARE TIRE SIZE COLD TIRE INFLATION PRESSURE CE oo s XXXXXXXXXXXXXX XXXXXXXXXXXXXX TIRE AND LOAD INFORMATION SEE OWNERS MANUAL FOR ADDITIONAL IN
173. r s seat but the passenger airbag off or pass airbag off indicator lamp is lit it is possible that the person isn t sitting properly in the seat If this happens e Turn the vehicle off and ask the person to place the seatback in the full upright position e Have the person sit upright in the seat centered on the seat cushion with the person s legs comfortably extended e Restart the vehicle and have the person remain in this position for about two minutes This will allow the system to detect that person and enable the passenger s frontal airbag e If the indicator lamp remains lit even after this the person should be advised to ride in the rear seat Pass Airbag Off 7 Occupant Passenger Airbag Empty seat Disabled Small child in child safety Lit Disabled seat or booster Small child with safety belt Lit Disabled buckled or unbuckled Adult Enabled 102 Seating and Safety Restraints Even with Advanced Restraints Systems children 12 and under should be properly restrained in the back seat After all occupants have adjusted their seats and put on safety belts it s very important that they continue to sit properly A properly seated occupant sits upright leaning against the seat back and centered on the seat cushion with their feet comfortably extended on the floor Sitting improperly can increase the chance of injury in a crash event For example if an occupant slouches lies down turns sid
174. r Gasoline Engines by the American Petroleum Institute API An oil with this trademark symbol conforms to the current engine and emission system protection standards and fuel economy requirements of the International Lubricant Standardization and Approval Committee ILSAC comprised of U S and Japanese automobile manufacturers To protect your engine s warranty use Motorcraft SAE 5W 30 or an equivalent 5W 30 oil meeting Ford specification WSS M2C929 A Do not use supplemental engine oil additives cleaners or other engine treatments They are unnecessary and could lead to engine damage that is not covered by Ford warranty Change your engine oil according to the appropriate schedule listed in the scheduled maintenance information Ford production and aftermarket Motorcraft oil filters are designed for added engine protection and long life If a replacement oil filter is used that does not meet Ford material and design specifications start up engine noises or knock may be experienced It is recommended you use the appropriate Motorcraft oil filter or another brand meeting Ford specifications for your engine application 205 Maintenance and Specifications BATTERY Your vehicle is equipped with a Motorcraft maintenance free battery which normally does not require additional water during its life of service However for severe usage or in high temperature climates check the battery electrolyte level Refer
175. r door Use the power door lock control or manually lock the passenger door to ensure the vehicle is properly secured The system will wait 20 seconds after locking before triggering an alarm After the 20 second pre arm phase the power door unlock control is disabled for more information refer to Power door trim switch inhibit section earlier in this chapter to further protect your vehicle Disarming the system You can disarm the active anti theft system by any of the following actions e Unlock the doors by using the remote entry transmitter e Unlock the driver s door with the key in the door lock cylinder e Turn the ignition to the 3 ON position with a programmed coded ignition key Note Unlocking the trunk inhibits the motion and tilt sensing systems but the system continues to monitor the doors and hood Once the trunk becomes closed the motion and tilt sensing systems will re arm 75 Seating and Safety Restraints SEATING Notes Reclining the seatback can cause an occupant to slide under the seat s safety belt resulting in severe personal injuries in the event of a collision Do not pile cargo higher than the seatbacks to reduce the risk of injury in a collision or sudden stop Before returning the seatback to its original position make sure that cargo or any objects are not trapped behind the seatback After returning the seatback to its original position pull on the seatback to ensure that it has fully
176. r remote entry transmitters You must have all remote entry transmitters maximum of four available before beginning this procedure 69 Locks and Security To reprogram the remote entry transmitters 1 Ensure the vehicle is electronically unlocked 2 Put the key in the ignition 3 Cycle eight times rapidly within 10 seconds between the 1 OFF LOCK position and 3 ON Note The eighth turn must end in the 3 ON position The doors will lock then unlock to confirm that the programming mode has been activated 4 Within 20 seconds press any button on the remote entry transmitter Note If more than 20 seconds have passed you will need to start the procedure over again The doors will lock then unlock to confirm that this remote entry transmitter has been programmed 5 Repeat Step 4 to program each additional remote entry transmitter 6 Turn the ignition to the 1 OFF LOCK position after you have finished programming all of the remote entry transmitters Note After 20 seconds you will automatically exit the programming mode The doors will lock then unlock to confirm that the programming mode has been exited lIluminated entry The interior lamps illuminate when the remote entry system is used to unlock the door s The illuminated entry system will turn off the interior lights if e the ignition switch is turned to the 3 ON position or e the remote transmitter lock control is pressed or e after 25 s
177. r to help you In the United States Ford Motor Company Customer Relationship Center P O Box 624 Dearborn MI 48121 1 800 521 4140 TDD for the hearing impaired 1 800 232 5952 www customersaskford com In Canada Lincoln Centre Ford Motor Company of Canada Limited P O Box 2000 Oakville Ontario L6J 5E4 1 800 387 9333 www lincolncanada com In order to help you service your Lincoln vehicle please have the following information available when contacting the Lincoln Centre e Your telephone number home and business e The name of the authorized dealer and the city where the authorized dealer is located e The year and make of your vehicle e The date of vehicle purchase e The current odometer reading e The vehicle identification number VIN Additional Assistance If you still have a complaint involving a warranty dispute you may wish to contact the Dispute Settlement Board U S In some states in the U S you must directly notify Ford in writing before pursuing remedies under your state s warranty laws Ford is also allowed a final repair attempt in some states 183 Customer Assistance In the United States a warranty dispute must be submitted to the Dispute Settlement Board before taking action under the Magnuson Moss Warranty Act or to the extent allowed by state law before pursuing replacement or repurchase remedies provided by certain state laws This dispute handling procedure is not required
178. raint system warning light airbag light will be turned on for three seconds 4 Within 10 seconds of the light turning on at a moderate speed buckle then unbuckle the safety belt e This will disable the BeltMinder feature for that seating position if it is currently enabled As confirmation the restraint system warning light will flash 4 times per second for 3 seconds e This will enable the BeltMinder feature for that seating position if it is currently disabled As confirmation the restraint system warning light will flash 4 times per second for 3 seconds followed by 3 seconds with the light off then followed by the restraint system warning light flashing 4 times per second for 3 seconds again 96 Seating and Safety Restraints AIRBAG SUPPLEMENTAL RESTRAINT SYSTEM SRS Important SRS precautions The SRS is designed to work with the safety belt to help protect the driver and right front passenger from certain upper body injuries Airbags DO NOT inflate slowly there is a risk of injury from a deploying airbag All occupants of the vehicle including the driver should always properly wear their safety belts even when an air bag supplemental restraint system SRS is provided Always transport children 12 years old and under in the back seat and always properly use appropriate child restraints The National Highway Traffic Safety Administration NHTSA recommends a minimum distanc
179. raise it again when the door is closed To re calibrate the window pull the switch up to raise the window until it completes its travel and hold the switch up for 2 seconds Another possible effect of lost calibration is that the feature may not lower the window To re calibrate the window in this case lower the window until it completes its travel and hold the switch down for 2 seconds Immediately after releasing the window down switch pull the switch up to raise the window until it completes its travel and hold the switch up for 2 seconds Perform Short drop re calibration with doors closed only Re Calibrating with doors open will cause the window to continuously bounce back Rear Power Windows Convertible Only The rear quarter windows are operated by a single window switch located at the Driver door window controls Press and pull the window switch to open and close the windows e Push down and hold the switch to open e Pull up and hold the switch to close 46 Driver Controls EXTERIOR MIRRORS Power side view mirrors if equipped To adjust your mirrors 1 Rotate the control clockwise to adjust the right mirror and rotate the control counterclockwise to adjust the left mirror 2 Move the control in the direction you wish to tilt the mirror 3 Return to the center position to lock mirrors in place SPEED CONTROL IF EQUIPPED With speed control set you can maintain a speed of 30 mph 48 km h or more with
180. rake fully 160 Driving DRIVING THROUGH WATER If driving through deep or standing water is unavoidable proceed very slowly especially when the depth is not known Never drive through o water that is higher than the bottom aA of the wheel rims for cars or the bottom of the hubs for trucks When driving through water traction or brake capability may be limited Also water may enter your engine s air intake and severely damage your engine or your vehicle may stall Driving through deep water where the transmission vent tube is submerged may allow water into the transmission and cause internal transmission damage Once through the water always dry the brakes by moving your vehicle slowly while applying light pressure on the brake pedal Wet brakes do not stop the vehicle as quickly as dry brakes 161 Roadside Emergencies ROADSIDE ASSISTANCE Getting roadside assistance To fully assist you should you have a vehicle concern Ford Motor Company offers a complimentary roadside assistance program This program is separate from the New Vehicle Limited Warranty The service is available e 24 hours seven days a week e for the New Vehicle Limited Warranty period of three years or 36 000 miles 60 000 km whichever occurs first on Ford and Mercury vehicles and four years or 50 000 miles 80 000 km on Lincoln vehicles Roadside assistance will cover e a flat tire change with a good spare except Ford GT whic
181. rdant abilities of the seat materials Do not use cleaning solvents bleach or dye on the vehicle s safety belts as these actions may weaken the belt webbing Do not use chemical solvents or strong detergents when cleaning the seat mounted side airbag if equipped Such products could contaminate the side airbag system and affect performance of the side airbag in a collision LEATHER SEATS IF EQUIPPED Your leather seating surfaces have a clear protective coating over the leather 193 Cleaning e To clean use a soft cloth with Motorcraft Deluxe Leather and Vinyl Cleaner ZC 11 A Dry the area with a soft cloth e To help maintain its resiliency and color use the Motorcraft Deluxe Leather Care Kit ZC 11 D available from your authorized dealer e Do not use household cleaning products alcohol solutions solvents or cleaners intended for rubber vinyl and plastics or oil petroleum based leather conditioners These products may cause premature wearing of the clear protective coating Note In some instances color or dye transfer can occur when wet clothing comes in contact with leather upholstery If this occurs the leather should be cleaned immediately to avoid permanent staining UNDERBODY Flush the complete underside of your vehicle frequently Keep body and door drain holes free from packed dirt FORD AND LINCOLN MERCURY CAR CARE PRODUCTS Your Ford or Lincoln Mercury authorized dealer has many quality pro
182. re part of the front passenger s seat and safety belt The sensors are designed to detect the presence of a properly seated occupant and determine if the front passenger s frontal airbag should be enabled may inflate or disabled will not inflate The front passenger sensing system will disable will not inflate the front passenger s frontal airbag if e the front passenger seat is unoccupied or has small medium objects in the front seat e the system determines that an infant is present in a rear facing infant seat that is installed according to the manufacturer s instructions e the system determines that a small child is present in a forward facing child restraint that is installed according to the manufacturer s instructions e the system determines that a small child is present in a booster seat e a front passenger takes his her weight off of the seat for a period of time e achild or a small person occupies the front passenger seat For side airbag equipped vehicles the front passenger sensing system will turn off the passenger seat side airbag if e the seat is empty and safety belt is unbuckled The front passenger sensing system uses a passenger airbag off or A pass airbag off indicator which will OFF illuminate and stay lit to remind you that the front passenger frontal airbag is disabled The indicator lamp is located on the top right corner of the center stack of the instrument panel above
183. rinkle your clothes particularly if you are unbelted The people I m with don t Set the example teen deaths occur 4 wear belts times more often in vehicles with TWO or MORE people Children and younger brothers sisters imitate behavior they see 94 Seating and Safety Restraints Reasons given Consider T have an airbag Airbags offer greater protection when used with safety belts Frontal airbags are not designed to inflate in rear and side crashes or rollovers Td rather be thrown clear Not a good idea People who are ejected are 40 times more likely to DIE Safety belts help prevent ejection WE CAN T PICK OUR CRASH Do not sit on top of a buckled safety belt to avoid the BeltMinder chime Sitting on the safety belt will increase the risk of injury in an accident To disable one time or deactivate the BeltMinder feature please follow the directions stated below One time disable If at any time the driver front passenger quickly buckles then unbuckles the safety belt for that seating position the BeltMinder is disabled for the current ignition cycle The BeltMinder feature will enable during the same ignition cycle if the occupant buckles and remains buckled for approximately 30 seconds Confirmation is not given for the one time disable Deactivating activating the BeltMinder feature The driver and front passenger BeltMinder are deactivated activated independently Whe
184. river Controls MESSAGE CENTER IF EQUIPPED With the ignition in the ON position the message center located on your gogo TRIP instrument cluster displays i important vehicle information ooo000 m through a constant monitor of vehicle systems You may select display features on the message center for a display of status The system will also notify you of potential vehicle problems with a display of system warnings followed by a long indicator chime Note Refer to the SETUP menu in this section to select the Single or Dual mode display in your message center Selectable features Reset Press this control to select and reset functions shown in the INFO menu and SETUP menu SJ Setup menu Press this control for the following displays e System Check e Display Color e Units English Metric e Display Mode e Language 54 Driver Controls System check Selecting this function from the SETUP menu causes the message PRESS RESET center to cycle through each of the EOR S45 CHECK systems being monitored For each of the monitored systems the message center will indicate either an OK message or a warning message for two seconds Pressing the RESET control cycles the message center through each of the systems being monitored The sequence of the system check report and how it appears in the message center is as follows OIL PRESSURE CHARGING SYSTEM DRIVER DOOR PASS
185. rly the risk of a child being injured in a crash greatly increases 121 Tires Wheels and Loading INFORMATION ABOUT UNIFORM TIRE QUALITY GRADING New vehicles are fitted with tires that have a rating on them called Tire Quality Grades The Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width For example e Treadwear 200 Traction AA Temperature A These Tire Quality Grades are determined by standards that the United States Department of Transportation has set Tire Quality Grades apply to new pneumatic tires for use on passenger cars They do not apply to deep tread winter type snow tires space saver or temporary use spare tires tires with nominal rim diameters of 10 to 12 inches or limited production tires as defined in Title 49 Code of Federal Regulations Part 575 104 c 2 U S Department of Transportation Tire quality grades The U S Department of Transportation requires Ford Motor Company to give you the following information about tire grades exactly as the government has written it Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course For example a tire graded 150 would wear one and one half 1 1 2 times as well on the government course as a tire graded 100 The relative performance of tires depends upon the actual conditions of their u
186. rol SK a to decrease lower back firmness A ao Adjusting the front power seat if equipped Never adjust the driver s seat or seatback when the vehicle is moving 78 Seating and Safety Restraints Do not pile cargo higher than the seatbacks to avoid injuring people in a collision or sudden stop Always drive and ride with your seatback upright and the lap belt snug and low across the hips Reclining the seatback can cause an occupant to slide under the seat s safety belt resulting in severe personal injuries in the event of a collision Sitting improperly out of position or with the seat back reclined too far can take off weight from the seat cushion and affect the decision of the passenger sensing system resulting in serious injury or death in a crash Always sit upright against your seatback with your feet on the floor To reduce the risk of possible serious injury Do not hang objects off seat back or stow objects in the seatback map pocket if equipped when a child is in the front passenger seat Do not place objects underneath the front passenger seat or between the seat and the center console Gif equipped Check the passenger airbag off or pass airbag off indicator lamp for proper airbag status Refer to Front passenger sensing system section for additional details Failure to follow these instructions may interfere with the front passenger seat sensing system The control is located on the
187. rs and the driver seat position sensor In addition the RCM also monitors the restraints warning light in the instrument cluster A difficulty with the system is indicated by one or more of the following e The warning light will either flash or stay lit e The warning light will not iluminate immediately after ignition is turned on e A series of five beeps will be heard The tone pattern will repeat periodically until the problem and warning light are repaired If any of these things happen even intermittently have the Personal Safety System serviced at an authorized dealer immediately Unless serviced the system may not function properly in the event of a collision Safety restraints precautions Always drive and ride with your seatback upright and the lap belt snug and low across the hips To reduce the risk of injury make sure children sit in the back seat where they can be properly restrained Never let a passenger hold a child on his or her lap while the vehicle is moving The passenger cannot protect the child from injury in a collision All occupants of the vehicle including the driver should always properly wear their safety belts even when an airbag supplemental restraint system SRS is provided It is extremely dangerous to ride in a cargo area inside or outside of a vehicle In a collision people riding in these areas are more likely to be seriously injured or killed Do not allow people to ride in any
188. rs 77 Servicing your vehicle 196 Setting the clock AM FM CD erretenaren 20 AM FM In dash 6 CD 008 24 Spark plugs specifications siirsin 228 234 Specification chart TUDTICANUS Sessies 232 234 Speed CONMOL i ccsusiswiecheiecsicds 47 Starting your vehicle sroesirsrsew 146 147 149 jump starting 0 eee 176 Steering wheel HUNE nieren ananena 43 T Tilt steering wheel 0 43 TEES isansa 122 123 171 alignment srrcrrrrenesieie 129 CE e A A 126 Changing eceso 171 173 checking the pressure 126 inspecting and inflating 124 TaD Gls eisescedtecasiesteis nranti 135 replacing isicssassesouniers dorveereessanes 128 YOUAUING ccccseussecdeaocnces ansvecoessesbes 129 Safety Practices ssssesirucriser 128 sidewall information 130 snow tires and chains 136 Spare CITE mesrine akion 171 terminology cccceeeeeeeeeees 123 tire grades sesceh senscigess ested aes 123 treadwear eee 122 127 TOWNE sisese oia 142 recreational towing 0 145 trailer tOWIN c ees 142 WYECKEP seismise ennie 181 Traction COntrol ss isssevssesscssceiss 152 Traction lok rear axle 154 Transmission automatic operation 154 brake shift interlock BSD 154 fluid checking and adding AUTOMATIC eee cece eeeeees 226 fluid checking and adding manual y csc hss cdessessacseekenctereds 227 flui
189. rst or e the remainder of your new vehicle limited warranty This means that Genuine Ford Accessories purchased along with your new vehicle and installed by the authorized dealer are covered for the full length of your New Vehicle s Limited Warranty 3 years or 36 000 miles 60 000 km whichever occurs first Contact your authorized dealer for details and a copy of the warranty Not all accessories are available for all models The following is a list of several Genuine Ford Accessory products Not all accessories are available for all models For a complete listing of the accessories that are available for your vehicle please contact your authorized dealer or visit our online store at www fordaccessoriesstore com Exterior style Bug shields Chrome exhaust tip Deflectors Front end covers Fog lights Splash guards Spoiler Wheels Interior style Electrochromatic compass temperature interior mirrors Floor mats 239 Accessories Lifestyle Bike racks Cargo organization and management Peace of mind First aid and highway safety kits Full vehicle covers Locking gas cap Keyless entry keypad Remote start Vehicle security systems Mobile ease hands free communication system Wheel locks For maximum vehicle performance keep the following information in mind when adding accessories or equipment to your vehicle e When adding accessories equipment passengers and luggage to your vehicle do not exceed the total
190. s Check brake system Warning returns after the ignition key Low brake fluid level is turned from OFF to ON DRIVER S DOOR AJAR Displayed when the driver s door is not completely closed PASSENGER DOOR AJAR Displayed when the passenger side door is not completely closed TRUNK AJAR Displayed when the trunk is not completely closed LOW FUEL LEVEL Displayed as an early reminder of a low fuel condition CHECK CHARGING SYSTEM Displayed when the electrical system is not maintaining proper voltage If you are operating electrical accessories 60 Driver Controls when the engine is idling at a low speed turn off as many of the electrical loads as soon as possible If the warning stays on or comes on when the engine is operating at normal speeds have the electrical system checked as soon as possible PARK BRAKE ON Displayed when the manual park brake is set If the warning stays on after the park brake is released contact your authorized dealer as soon as possible CHECK BRAKE SYSTEM Displayed when the braking system is not operating properly If the warning stays on or continues to come on contact your authorized dealer as soon as possible LOW BRAKE FLUID LEVEL Indicates the brake fluid level is low and the brake system should be inspected immediately Refer to Brake fluid reservoir in the Maintenance and Specifications chapter LOW OIL PRESSURE Displayed when the engine oil pressure is low If this warning messa
191. s maximum permissible pressure and or the pressure at which the maximum load can be carried by the tire This pressure is normally higher than the manufacturer s recommended cold inflation pressure which can be found on the Safety Compliance Certification Label or Tire Label which is located on the B Pillar or the edge of the driver s door The cold inflation pressure should never be set lower than the recommended pressure on the Safety Compliance Certification Label or Tire Label When weather temperature changes occur tire inflation pressures also change A 10 F 6 C temperature drop can cause a corresponding drop of 1 psi 7 kPa in inflation pressure Check your tire pressures frequently and adjust them to the proper pressure which can be found on the Safety Compliance Certification Label or Tire Label If you are checking tire pressure when the tire is hot i e driven more than 1 mile 1 6 km never bleed or reduce air pressure The tires are hot from driving and it is normal for pressures to increase above recommended cold pressures A hot tire at or below recommended cold inflation pressure could be significantly under inflated 125 Tires Wheels and Loading To check the pressure in your tire s 1 Make sure the tires are cool meaning they are not hot from driving even a mile Note If you have to drive a distance to get air for your tire s check and record the tire pressure first and add the appropriate air
192. s Guide for all other required information and warnings Introduction These are some of the symbols you may see on your vehicle Vehicle Symbol Glossary Safety Alert A i T fe a Tether iN Anti Lock Brake System s Powertrain Malfunction 1 ELY Master Lighting Switch W Ca 0 vis WY Fasten Safety Belt Airbag Side Child Seat Installation Warning Fog Lamps Front Fuel Pump Reset Windshield Defrost Demist See Owner s Guide Airbag Front Child Seat Child Seat Lower Anchor Brake System Brake Fluid Non Petroleum Based Speed Control Hazard Warning Flasher Fuse Compartment Windshield Wash Wipe Rear Window Defrost Demist ry gt JOS OF eroen t 2 Introduction Vehicle Symbol Glossary Power Windows Front Rear Child Safety Door Lock Unlock Panic Alarm Engine Coolant Do Not Open When Hot Avoid Smoking Flames or Sparks Explosive Gas Power Steering Fluid Emission System Passenger Compartment e Air Filter Check Fuel Cap OD ES B Power Window Lockout Interior Luggage Compartment Release Symbol Engine Oil Engine Coolant Temperature Battery Battery Acid Fan Warning Maintain Correct Fluid Level Engine Air Filter Jack Low Tire Pressure Warning B Ze Ci gt LI fi Cf deh Vv CY Instrument Cluster WARNING LIGHTS AND CHIMES Base instrument cluster Beis
193. s a straight forward and relatively speedy alternative to resolve a disagreement when all other efforts to produce a settlement have failed This procedure is without cost to you and is designed to eliminate the need for lengthy and expensive legal proceedings In the CAMVAP program impartial third party arbitrators conduct hearings at mutually convenient times and places in an informal environment These impartial arbitrators review the positions of the parties make decisions and when appropriate render awards to resolve disputes CAMVAP decisions are fast fair and final as the arbitrator s award is binding both to you and Ford of Canada CAMVAP services are available in all territories and provinces For more information without charge or obligation call your CAMVAP Provincial Administrator directly at 1 800 207 0685 FORD EXTENDED SERVICE PLAN You can get more protection for your new car or light truck by purchasing Ford Extended Service Plan Ford ESP coverage It provides the following e Benefits during the warranty period depending on the plan you purchase such as reimbursement for rentals coverage for certain maintenance and wear items e Protection against covered repair costs after your Bumper to Bumper Warranty expires You may purchase Ford ESP from any participating authorized dealer There are several plans available in various time distance and deductible combinations which can be tailored to fit your own
194. s air through the windshield defroster vents Can be used to clear the windshield of fog and thin ice 3 Rear defroster RL Press to activate deactivate the rear window defroster Refer to Rear window defroster later in this section for more information 4 Recirculation control A Press to activate deactivate air recirculation in cabin Recirculated air may reduce the amount of time to cool down the interior of the vehicle and may also help reduce undesired exterior odors from reaching the interior of the vehicle Recirculation engages automatically with selection of MAX A C or can be engaged manually in any other mode selection except WY defrost Recirculation may turn off automatically in all airflow selections except MAX A C 5 A C Press to activate deactivate air conditioning Use with recirculated air to improve cooling performance Engages automatically in MAX A C G7 defrost and YA floor defrost 30 Climate Controls 6 Fan speed adjustment Controls the volume of air circulated in the vehicle Operating tips e To reduce fog build up on the windshield during humid weather place the air flow selector in the U7 defrost position e To reduce humidity build up inside the vehicle do not drive with the airflow selector in the O OFF position or with recirculated air engaged e Do not put objects under the front seats that will interfere with the airflow to the back seats e Remove any snow ice or leaves fro
195. s been in an accident the alignment of your headlamps should be checked by your authorized dealer Headlamp vertical aim adjustment 1 Park the vehicle directly in front of a wall or screen on a level surface approximately 25 feet 7 6 meters away 34 e 1 8 feet 2 4 meters e 2 Center height of lamp to ground e 8 25 feet 7 6 meters e 4 Horizontal reference line 2 Measure the height from the center of your headlamp to the ground and mark an 8 foot 2 4 meter horizontal reference line on the vertical wall or screen at this height a piece of masking tape works well The center of the lamp is marked by a 3 0 mm circle on the headlamp lens 3 Turn on the low beam headlamps to illuminate the wall or screen and open the hood 4 On the wall or screen you will observe a flat zone of high intensity light located at the top of the beam pattern 5 If the top edge of the high intensity light zone is not at the horizontal reference line the headlamp will need to be adjusted 6 Locate the vertical adjuster on each headlamp then use a 7 mm Allen wrench or a Phillips screwdriver to adjust the headlamp up or down 7 HORIZONTAL AIM IS NOT REQUIRED FOR THIS VEHICLE AND IS NON ADJUSTABLE 8 Close the hood and turn off the lamps 35 Lights TURN SIGNAL CONTROL p gt e Push down to activate the left turn signal e Push up to activate the right turn signal 4 The flash rate of
196. s door and you lock the vehicle with the power door lock control all the doors will lock then the driver s door will automatically unlock reminding you that your key is still in the ignition The vehicle can still be locked with the key in the ignition using the manual lock button on the door locking the driver s door with a key or using the lock button on the remote entry transmitter 63 Locks and Security Autolock if equipped On vehicles equipped with an automatic transmission this feature automatically locks all vehicle doors when e all doors are closed e the ignition is in the 3 ON position e the brake is pressed before reaching 5 mph 8 km h and e then the vehicle increases to more than 5 mph 8 km h Relock The autolock feature repeats when e an autolock occurrence has already taken place e the brake is depressed while vehicle speed is less than 5 mph 8 km h e any vehicle door is opened and then all doors become closed again and e then the vehicle increases to more than 5 mph 8 km h Deactivating activating the autolock feature Before following the procedure make sure that the ignition is in the 1 OFF LOCK position and all vehicle doors are closed You must complete Steps 1 7 within 30 seconds or the procedure will have to be repeated If the procedure needs to be repeated you must wait 30 seconds 1 Turn the ignition to the 3 ON position 2 Press the power door unlock con
197. s ici cessiesssacsnes 151 244 Parts see Motorcraft parts 228 Passenger Occupant Classification Sensor 0008 83 Power distribution box see FUSES woeceeeceeccceeeesseeeeesteeees 167 Power door locks cccccceeees 64 Power MULTOTS ceeeceeeeseeeeene 47 Power POINE c cc eececcceeeeseeeeeene 43 Power steering c eeeee 153 fluid checking and adding 225 fluid refill capacity 0 0 0 230 fluid specifications 232 234 Power Windows ccccsseeeee 44 R FRAGIO a aA 19 22 Relays o eeceecccccsesssceseseeeeeesseeeeees 164 Remote entry system 0 67 illuminated entry cee 70 opening the trunk 00 68 Roadside assistance 0 666 162 S Safety Belt Maintenance 91 Safety belts see Safety restraints 82 85 86 88 89 Safety defects reporting 188 Safety restraints 82 85 86 88 90 belt Minder rossis 92 extension assembly 00 90 fOr ACUIUS pigresa 86 88 89 for children sisrisssieess 107 108 Occupant Classification DONISOP a aare E E aS 83 safety belt maintenance 91 warning light and chime 91 92 Safety seats for children 112 Safety Compliance Certification Label 00 236 Seat belts see Safety VOStLaiNtS sssdceiesscchsstasagesadivaseeeaeess 82 SOabS EEE AEAEE 76 child safety seats 00n 000n00 112 front SAt arret re
198. s or internal injuries particularly to occupants who are not properly restrained or are otherwise out of position at the time of airbag deployment It is extremely important that occupants be properly restrained as far away from the airbag module as possible while maintaining vehicle control The SRS consists of e driver and passenger airbag modules which include the inflators and airbags one or more impact and safing sensors a readiness light and tone a diagnostic module and the electrical wiring which connects the components The diagnostic module monitors its own internal circuits and the supplemental airbag electrical system wiring including the impact sensors the system wiring the airbag system readiness light the airbag back up power and the airbag ignitors Several air bag system components get hot after inflation Do not touch them after inflation If the air bag has deployed the air bag will not function again and must be replaced immediately If the air bag is not replaced the unrepaired area will increase the risk of injury in a collision 100 Seating and Safety Restraints Front passenger sensing system The front passenger sensing system is designed to meet the regulatory requirements of Federal Motor Vehicle Safety Standard FMVSS 208 and is designed to disable will not inflate the front passenger s frontal airbag under certain conditions The front passenger sensing system works with sensors that a
199. se however and may depart significantly from the norm due to variations in driving habits service practices and differences in road characteristics and climate Traction AA ABC The traction grades from highest to lowest are AA A B and C The grades represent the tire s ability to stop on wet pavement as measured under controlled conditions on specified government test surfaces of asphalt and concrete A tire marked C may have poor traction performance 122 Tires Wheels and Loading The traction grade assigned to this tire is based on straight ahead braking traction tests and does not include acceleration cornering hydroplaning or peak traction characteristics Temperature A B C The temperature grades are A the highest B and C representing the tire s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel Sustained high temperature can cause the material of the tire to degenerate and reduce tire life and excessive temperature can lead to sudden tire failure The grade C corresponds to a level of performance which all passenger car tires must meet under the Federal Motor Vehicle Safety Standard No 109 Grades B and A represent higher levels of performance on the laboratory test wheel than the minimum required by law The temperature grade for this tire is established for a tire that is properly inflated and not overl
200. sition Replacing the battery The remote entry transmitter uses one coin type three volt lithium battery CR2032 or equivalent 68 Locks and Security To replace the battery 1 Twist a thin coin between the two halves of the remote entry transmitter near the key ring DO NOT TAKE THE RUBBER COVER AND CIRCUIT BOARD OFF THE FRONT HOUSING OF THE REMOTE ENTRY TRANSMITTER 2 Do not wipe off any grease on the battery terminals on the back surface of the circuit board STVNIWYS HONOL LO ATVH Y3HLO Ni AYSLLVE 3DV1d 3 Remove the old battery Note Please refer to local regulations when disposing of transmitter batteries 4 Insert the new battery Refer to the diagram inside the remote entry transmitter for the correct orientation of the battery Press the battery down to ensure that the battery is fully seated in the battery housing cavity 5 Snap the two halves back together Note Replacement of the battery will not cause the remote transmitter to become deprogrammed from your vehicle The remote transmitter should operate normally after battery replacement Replacing lost remote entry transmitters If you would like to have your remote entry transmitter reprogrammed because you lost one or would like to buy additional remote entry transmitters you can either reprogram them yourself or take all remote entry transmitters to your authorized dealer for reprogramming How to reprogram you
201. ssential to the life and performance of your vehicle and to its emissions system 228 Maintenance and Specifications For PCV valve replacement see your authorized dealer Refer to scheduled maintenance information for the appropriate intervals for changing the PCV valve Replace the PCV valve with one that meets Ford material and design specifications for your vehicle such as a Motorcraft or equivalent replacement part The customer warranty may be void for any damage to the emissions system if such a PCV valve is not used For spark plug replacement see your authorized dealer Refer to scheduled maintenance information for the appropriate intervals for changing the spark plugs Replace the spark plugs with ones that meet Ford material and design specifications for your vehicle such as Motorcraft or equivalent replacement parts The customer warranty may be void for any damage to the engine if such spark plugs are not used 229 Maintenance and Specifications REFILL CAPACITIES Fluid Ford Part Application Capacity Name Brake fluid and Motorcraft High All clutch fluid if equipped Engine oil includes filter change Engine coolant Power steering fluid Rear axle lubricant Performance DOT 3 Motor Vehicle Brake Fluid Motorcraft SAE 5W 20 Premium Synthetic Blend Motor Oil US Motorcraft SAE 5W 20 Super Premium Motor Oil Canada Motorcraft SAE 5W 30 Premium Synthetic Blend M
202. ssion or transaxle XXXX XX XXXX XX RIMS each code represents AT XXX kPa XX PSI AT XXX kPa XX PSI COLD THIS VEHICLE CONFORMS TO ALL APPLICABLE FEDERAL MOTOR VEHICLE SAFETY AND THEFT PREVENTION STANDARDS IN EFFECT ON THE DATE OF MANUFACTURE SHOWN ABOVE VIN XXXXXXXXXXXXXXXXX XXXXX TYPE XXX XXXXX EXT PNT _ XX RC XX DSO WBTBRK TINTTR TPPS R AXLE TR SPR XXXXX XXX X XX X XX X XX XXX XXXXXXXXXXXXX UTC V2USA 1520472 AA Five speed manual T5 Five speed manual TR3650 Five speed automatic 6R55S 238 Accessories GENUINE FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of Genuine Ford Accessories are available for your vehicle through your local authorized Ford or Ford of Canada dealer These quality accessories have been specifically engineered to fulfill your automotive needs they are custom designed to complement the style and aerodynamic appearance of your vehicle In addition each accessory is made from high quality materials and meets or exceeds Ford s rigorous engineering and safety specifications Ford Motor Company will repair or replace any properly dealer installed Genuine Ford Accessory found to be defective in factory supplied materials or workmanship during the warranty period as well as any component damaged by the defective accessory The accessory will be warranted for whichever provides you the greatest benefit e 12 months or 12 000 miles 20 000 km whichever occurs fi
203. strument Cluster chapter Distance to empty DTE Selecting this function from the INFO menu estimates approximately how far you can drive with the fuel remaining in your tank under normal driving conditions Remember to turn the ignition OFF when refueling to allow this feature to correctly detect the added fuel 57 Driver Controls Single mode display XXX mi T E 880000 0 mi Dual mode display XXX ULES T E opaga m 000 0 The DTE function will display LOW FUEL LEVEL and sound a tone for one second when you have approximately 50 miles 80 km to empty If you RESET this warning message this display and tone will return within 10 minutes DTE is calculated using a running average fuel economy which is based on your recent driving history of 500 miles 800 km This value is not the same as the average fuel economy display The running average fuel economy is reinitialized to a factory default value if the battery is disconnected Average fuel economy AFE Select this function from the INFO menu to display your average fuel VY V 7 economy in miles gallon or liters 100 XX X AVERAGE NPG km O80000 m 800 0 If you calculate your average fuel economy by dividing miles traveled by gallons of fuel used liters of fuel used by 100 kilometers traveled your figure may be different than displayed for the following reasons e Your vehicle was not perfectly level during fill up e Differences in the a
204. t NEVER place a rear facing child seat in front of an active airbag If you must use a forward facing child seat in the front seat move the seat all the way back How does the airbag supplemental restraint system work The airbag SRS is designed to activate when the vehicle sustains a longitudinal deceleration sufficient to cause the airbag sensors to close an electrical circuit that initiates airbag inflation The fact that the airbags did not inflate in a collision does not mean that something is wrong with the system Rather it means the forces were not sufficient enough to cause activation Airbags are designed to inflate in frontal and near frontal collisions not rollover side impact or rear impacts unless the collision causes sufficient longitudinal deceleration 99 Seating and Safety Restraints The airbags inflate and deflate rapidly upon activation After airbag deployment it is normal to notice a smoke like powdery residue or smell the burnt propellant This may consist of cornstarch talcum powder or sodium compounds which may irritate the skin and eyes but none of the residue is toxic While the SRS is designed to help reduce serious injuries contact with a deploying airbag may also cause abrasions swelling or temporary hearing loss Because airbags must inflate rapidly and with considerable force there is the risk of death or serious injuries such as fractures facial and eye injurie
205. t e Rear passenger feet and knees resting or pushing on the seat The conditions listed above may cause the weight of a properly seated occupant to be incorrectly interpreted by the front passenger sensing system The person in the front passenger seat may appear heavier or lighter due to the conditions described in the list above To reduce the risk of possible serious injury Do not stow objects in seat back map pocket if equipped or hang objects off seat back if a child is in the front passenger seat Do not place objects underneath the front passenger seat or between the seat and the center console Gf equipped Check the passenger airbag off or pass airbag off indicator lamp for proper airbag Status Failure to follow these instructions may interfere with the front passenger seat sensing system In case there is a problem with the o front passenger sensing system the airbag readiness lamp in the IN instrument cluster will stay lit If the airbag readiness lamp is lit do the following The driver and or adult passengers should check for any objects that may be lodged underneath the front passenger seat or cargo interfering with the seat If objects are lodged and or cargo is interfering with the seat please take the following steps to remove the obstruction e Pull the vehicle over e Turn the vehicle off e Driver and or adult passengers should check for any objects lodged underneath the front passenger se
206. t attempt to service repair or modify the airbag SRS its fuses or the seat cover on a seat containing an airbag See your authorized dealer All occupants of the vehicle should always wear their safety belts even when an airbag SRS is provided 105 Seating and Safety Restraints How does the side airbag system work The design and development of the side airbag system included recommended testing procedures that were developed by a group of automotive safety experts known as the Side Airbag Technical Working Group These recommended testing procedures help reduce the risk of injuries related to the deployment of side airbags The side airbag system consists of the following e An inflatable nylon bag airbag with a gas generator concealed behind the outboard bolster of the driver and front passenger seatbacks e A special seat cover designed to allow airbag deployment e The same warning light electronic control and diagnostic unit as used for the front airbags e Two crash sensors located under the outboard side of the front seats attached to the floor Side airbags in combination with safety belts can help reduce the risk of severe injuries in the event of a significant side impact collision The side airbags are fitted on the outboard side of the seatbacks of the front seats In certain lateral collisions the airbag on the side affected by the collision will be inflated The front passenger sensing s
207. t sunlight e Always use a clean sponge or car wash mitt with plenty of water for best results e Dry the vehicle with a chamois or soft terry cloth towel in order to eliminate water spotting e It is especially important to wash the vehicle regularly during the winter months as dirt and road salt are difficult to remove and cause damage to the vehicle e Immediately remove items such as gasoline diesel fuel bird droppings and insect deposits because they can cause damage to the vehicle s paintwork and trim over time e Remove any exterior accessories such as antennas before entering a car wash e Suntan lotions and insect repellents can damage any painted surface if these substances come in contact with your vehicle wash off as soon as possible WAXING Applying Motorcraft Paint Sealant ZC 45 to your vehicle every six months will assist in reducing minor scratches and paint damage e Wash the vehicle first e Do not use waxes that contain abrasives use Motorcraft Premium Liquid Wax ZC 53 A which is available from your authorized dealer or an equivalent quality product e Do not allow paint sealant to come in contact with any non body ow gloss black colored trim such as grained door handles roof racks bumpers side moldings mirror housings or the windshield cowl area The paint sealant will gray or stain the parts over time PAINT CHIPS Your authorized dealer has touch up paint and sprays to match your ve
208. tart the engine and take your vehicle to an authorized dealer Driving the vehicle without repairing the engine problem increases the chance of engine damage Take your vehicle to an authorized dealer as soon as possible WHAT YOU SHOULD KNOW ABOUT AUTOMOTIVE FUELS fg Important safety precautions Do not overfill the fuel tank The pressure in an overfilled tank may cause leakage and lead to fuel spray and fire The fuel system may be under pressure If the fuel filler cap is venting vapor or if you hear a hissing sound wait until it stops before completely removing the fuel filler cap Otherwise fuel may spray out and injure you or others If you do not use the proper fuel filler cap excessive pressure or vacuum in the fuel tank may damage the fuel system or cause the fuel cap to disengage in a collision which may result in possible personal injury Automotive fuels can cause serious injury or death if misused or mishandled A Gasoline may contain benzene which is a cancer causing agent 214 Maintenance and Specifications Observe the following guidelines when handling automotive fuel e Extinguish all smoking materials and any open flames before refueling your vehicle e Always turn off the vehicle before refueling e Automotive fuels can be harmful or fatal if swallowed Fuel such as gasoline is highly toxic and if swallowed can cause death or permanent injury If fuel is swallowed call a physician immediatel
209. tem is under pressure steam and hot liquid can come out forcefully when the cap is loosened slightly 1 Before you begin turn the engine off and let it cool 2 When the engine is cool wrap a thick cloth around the coolant pressure relief cap on the coolant reservoir a translucent plastic bottle Slowly turn cap counterclockwise left until pressure begins to release 3 Step back while the pressure releases 4 When you are sure that all the pressure has been released use the cloth to turn it counterclockwise and remove the cap 5 Fill the coolant reservoir slowly with the proper coolant mixture see above to within the COLD FILL RANGE or the FULL COLD level on the reservoir If you removed the radiator cap in an overflow system fill the radiator until the coolant is visible and radiator is almost full 6 Replace the cap Turn until tightly installed Cap must be tightly installed to prevent coolant loss After any coolant has been added check the coolant concentration refer to Checking engine coolant If the concentration is not 50 50 protection to 34 F 36 C drain some coolant and adjust the concentration It may take several drains and additions to obtain a 50 50 coolant concentration Whenever coolant has been added the coolant level in the coolant reservoir should be checked the next few times you drive the vehicle If necessary add enough 50 50 concentration of engine coolant and distilled w
210. the front seat move the seat all the way back Always transport children 12 years old and under in the back seat and always properly use appropriate child restraints 83 Seating and Safety Restraints The front passenger sensing system can automatically turn off the passenger front airbag The system is designed to help protect small child size occupants from airbag deployments when they are improperly seated or restrained in the front passenger seat contrary to proper child seating or restraint usage recommendations Even with this technology parents are STRONGLY encouraged to always properly restrain children in the rear seat The sensor also turns off the passenger front airbag and side airbag if equipped when the passenger seat is empty to prevent unnecessary replacement of airbag s after a collision When the front passenger seat is occupied and the sensing system has turned off the passenger s frontal airbag the pass airbag off indicator will light and stay lit to remind you that the front passenger frontal airbag is off See Front passenger sensing system in the airbags section of this chapter Front safety belt usage sensors The front safety belt usage sensors detect whether or not the driver and front outboard passenger safety belts are fastened This information allows your Personal Safety System to tailor the airbag deployment and safety belt pretensioner activation depending upon safety belt usage Refer to Saf
211. the turn signal will speed up considerably if the Lighting Control Module detects a left or right turn lamp bulb front or rear is burned out INTERIOR LAMPS Map lamps Press the controls on either side of the lamp to turn the light on BULB REPLACEMENT Headlamp Condensation The headlamps are vented to equalize pressure When moist air enters the headlamp s through the vents there is a possibility that condensation can occur This condensation is normal and will clear within 45 minutes of headlamp operation Replacing exterior bulbs Check the operation of all the bulbs frequently 36 Lights Using the right bulbs Replacement bulbs are specified in the chart below Headlamp bulbs must be marked with an authorized D O T for North America and an E for Europe to ensure lamp performance light brightness and pattern and safe visibility The correct bulbs will not damage the lamp assembly or void the lamp assembly warranty and will provide quality bulb burn time Park lamp turn lamp side marker front Cif equipped W5W Interior bulbs Check the operation of all bulbs frequently Replacing headlamp bulbs To remove the headlamp bulb 1 Make sure headlamp switch is in the OFF position then open the hood 2 Disconnect the electrical connector from the bulb by depressing the retainer clip and pulling rearward 3 Remove the bulb by rotating it counterclockwise and pulling it straight out
212. the vehicle is sounds for 6 seconds every 30 traveling at least 3 mph 5 seconds repeating for approximately km h and more than 1 2 5 minutes or until the safety belts are minutes have elapsed since the buckled ignition switch has been turned to ON 93 Seating and Safety Restraints The following are reasons most often given for not wearing safety belts All statistics based on U S data Reasons given Consider Crashes are rare events 36700 crashes occur every day The more we drive the more we are exposed to rare events even for good drivers 1 in 4 of us will be seriously injured in a crash during our lifetime Tm not going far 3 of 4 fatal crashes occur within 25 miles 40 km of home Belts are uncomfortable We design our safety belts to enhance comfort If you are uncomfortable try different positions for the safety belt upper anchorage and seatback which should be as upright as possible this can improve comfort T was in a hurry Prime time for an accident BeltMinder reminds us to take a few seconds to buckle up Safety belts don t work Safety belts when used properly reduce risk of death to front seat occupants by 45 in cars and by 60 in light trucks Traffic is light Nearly 1 of 2 deaths occur in single vehicle crashes many when no other vehicles are around Belts wrinkle my clothes Possibly but a serious crash can do much more than w
213. the window sticker is not supplied with your vehicle The EPA window sticker should be your guide for the fuel economy comparisons with other vehicles It is important to note the box in the lower left corner of the window sticker These numbers represent the Range of MPG L 100 km expected on the vehicle under optimum conditions Your fuel economy may vary depending upon the method of operation and conditions EMISSION CONTROL SYSTEM tC Your vehicle is equipped with various emission control components and a catalytic converter which will enable your vehicle to comply with applicable exhaust emission standards To make sure that the catalytic converter and other emission control components continue to work properly e Use only the specified fuel listed e Avoid running out of fuel e Do not turn off the ignition while your vehicle is moving especially at high speeds e Have the items listed in scheduled maintenance information performed according to the specified schedule The scheduled maintenance items listed in scheduled maintenance information are essential to the life and performance of your vehicle and to its emissions system If other than Ford Motorcraft or Ford authorized parts are used for maintenance replacements or for service of components affecting emission control such non Ford parts should be equivalent to genuine Ford Motor Company parts in performance and durability 222 Maintenance and Specifications
214. ting range for your remote entry transmitter is approximately 33 feet 10 meters A decrease in operating range could be caused by e weather conditions e nearby radio towers e structures around the vehicle or e other vehicles parked next to your vehicle Your vehicle is equipped with a remote entry system which allows you to e unlock the vehicle doors without a key e lock all the vehicle doors without a key e activate the personal alarm e release the decklid e arm and disarm the active anti theft system Gf equipped If there are problems with the remote entry system make sure to take ALL remote entry transmitters with you to the authorized dealer in order to aid in troubleshooting the problem Unlocking the doors f 1 Press f and release to unlock the driver s door Note The interior lamps will illuminate and the active anti theft system if equipped will disarm 2 Press Wy and release again within three seconds to unlock the passenger door 67 Locks and Security Locking the doors amp 1 Press and release to lock all the doors Note The interior lamps will turn off unless the dome lamp control is in the full up position and the turn signal lamps will flash if all doors trunk and hood if equipped with active anti theft system are closed and locked If the vehicle is not equipped with the active anti theft system the turn signal lamps will flash if all doors and the trunk are close
215. tion all seat belts should be checked for proper function BELT AND RETRACTOR ASSEMBLY MUST BE REPLACED if the seat belt assembly automatic locking retractor feature or any other seat belt function is not operating properly when checked by an authorized dealer Failure to replace the Belt and Retractor assembly could increase the risk of injury in collisions Safety belt pretensioner Your vehicle is equipped with safety belt pretensioners at the driver and front outboard passenger seating positions The safety belt pretensioner is a device which removes excess webbing from the safety belt system The safety belt pretensioner uses the same crash sensor system as the front airbag supplemental restraint system SRS When the safety belt pretensioner deploys webbing from the lap and shoulder belt is tightened Refer to the Safety belt maintenance section in this chapter The driver and front passenger seat belt system including retractors buckles and height adjusters must be replaced if the vehicle is involved in a collision that results in deployment of front airbags and safety belt pretensioners Safety belt extension assembly If the safety belt is too short when fully extended there is a 8 inch 20 cm safety belt extension assembly that can be added part number 611022 This assembly can be obtained from an authorized dealer 90 Seating and Safety Restraints Use only extensions manufactured by the same supplier
216. tional floor mats on top of the factory installed PT floor mats as they may interfere with the throttle brake and clutch pedals 62 Locks and Security KEYS One key operates all the locks and starts the vehicle Always carry a spare key with you in case of an emergency Your keys are programmed to your vehicle using a non programmed key will not permit your vehicle to start If you lose your authorized dealer supplied keys replacement keys are available through your authorized dealer Refer to the SecuriLock passive anti theft system section later in this chapter for more information POWER DOOR LOCKS The power door lock controls are located on the driver and front passenger door panels Press the control to unlock all doors Note When the active anti theft system if equipped is armed and the power door trim switch inhibit feature the default for power door switch inhibit feature is disabled has been activated via the driver configuration process control of the interior power door locks is disabled until the vehicle is disarmed For more information about the driver configuration process refer to the Deactivating activating the power door trim switch inhibit feature section later in this chapter Press the a control to lock all doors Smart locks This feature helps prevent you from locking yourself out of the vehicle if your key is still in the ignition When you open the driver
217. tment door lid from within the luggage compartment pull the illuminated T shaped handle and push up on the trunk lid The handle is composed of a material that will glow for hours in darkness following brief exposure to ambient light The T shaped handle will be located either on the luggage compartment door lid or inside the luggage compartment near the tail lamps Keep vehicle doors and luggage compartment locked and keep keys and remote transmitters out of a child s reach Unsupervised children could lock themselves in the trunk and risk injury Children should be taught not to play in vehicles On hot days the temperature in the trunk or vehicle interior can rise very quickly Exposure of people or animals to these high temperatures for even a short time can cause death or serious heat related injuries including brain damage Small children are particularly at risk 66 Locks and Security REMOTE ENTRY SYSTEM This device complies with part 15 of the FCC rules and with RS 210 of Industry Canada Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment The typical opera
218. to crash severity and conditions A collection of crash sensors provides information to the Restraints Control Module RCM During a crash the RCM activates the safety belt pretensioners and or either none one or both stages of the dual stage airbag supplemental restraints based on crash severity and conditions The fact that the pretensioners or airbags did not activate for both front seat occupants in a collision does not mean that something is wrong with the system Rather it means the Personal Safety System determined the accident conditions crash severity belt usage etc were not appropriate to activate these safety devices Front airbags are designed to activate only in frontal and near frontal collisions not rollovers side impacts or rear impacts unless the collision causes sufficient longitudinal deceleration 82 Seating and Safety Restraints Driver and passenger dual stage airbag supplemental restraints The dual stage airbags offer the capability to tailor the level of airbag inflation energy A lower less forceful energy level is provided for more common moderate severity impacts A higher energy level is used for the most severe impacts Refer to Airbag Supplemental Restraints section in this chapter Front crash severity sensor The front crash severity sensor enhances the ability to detect the severity of an impact Positioned up front it provides valuable information early in the crash event on the severity o
219. to the vehicle or battery Lift the battery with a battery carrier or with your hands on opposite corners Keep batteries out of reach of children Batteries contain sulfuric acid Avoid contact with skin eyes or clothing Shield your eyes when working near the battery to protect against possible splashing of acid solution In case of acid contact with skin or eyes flush immediately with water for a minimum of 15 minutes and get prompt medical attention If acid is swallowed call a physician immediately Battery posts terminals and related accessories contain lead and lead compounds Wash hands after handling Because your vehicle s engine is electronically controlled by a computer some control conditions are maintained by power from the battery When the battery is disconnected or a new battery is installed the engine must relearn its idle and fuel trim strategy for optimum driveability and performance To begin this process 1 With the vehicle at a complete stop set the parking brake 2 Put the gearshift in P Park automatic transmission or the neutral position manual transmission turn off all accessories and start the engine 3 Run the engine until it reaches normal operating temperature 4 Allow the engine to idle for at least one minute 5 Turn the A C on and allow the engine to idle for at least one minute 6 Drive the vehicle to complete the relearning process e The vehicle may need to be driven 10 miles 1
220. trol three times 3 Turn the ignition from the 3 ON to the 1 OFF LOCK position 4 Press the power door unlock control three times 5 Turn the ignition back to the 3 ON position The horn will chirp 6 Press the unlock control then press the lock control The horn will chirp once if autolock was deactivated or twice one short and one long chirp if autolock was activated 7 Turn the ignition to the 1 OFF LOCK position The horn will chirp once to confirm the procedure is complete Central locking and unlocking feature Your vehicle s keys are designed to lock and unlock the driver s door as well as open the trunk 64 Locks and Security e The driver s door is unlocked when the key is inserted in the driver door key cylinder and turned to the unlock position The driver s door is locked when the key is inserted in the driver door key cylinder and turned to the lock position Note Locking the driver door with the key does not lock the passenger door Use the power door lock control or manually lock the passenger door to ensure the vehicle is properly secured Power door trim switch inhibit if equipped This feature disables the power door lock controls if all the doors are locked and the active anti theft system if equipped becomes armed For more information concerning the active anti theft system refer to Active anti theft system if equipped later in this chapter Once the power door trim switches are
221. ty fuel of the recommended octane rating Aftermarket products could cause damage to the fuel system Repairs to correct the effects of using an aftermarket product in your fuel may not be covered by your warranty Many of the world s automakers approved the World wide Fuel Charter that recommends gasoline specifications to provide improved performance and emission control system protection for your vehicle Gasolines that meet the World wide Fuel Charter should be used when available Ask your fuel supplier about gasolines that meet the World wide Fuel Charter Cleaner air Ford endorses the use of reformulated cleaner burning gasolines to improve air quality Running out of fuel Avoid running out of fuel because this situation may have an adverse effect on powertrain components If you have run out of fuel e You may need to cycle the ignition from off to on several times after refueling to allow the fuel system to pump the fuel from the tank to the engine 218 Maintenance and Specifications e The ee indicator may come on For more information on the Check Engine or the Service engine soon indicator refer to Warning lights and chimes in the Instrument Cluster chapter FUEL FILTER For fuel filter replacement see your authorized dealer Refer to scheduled maintenance information for the appropriate intervals for changing the fuel filter Replace the fuel filter with an authorized Motorcraft part The
222. u maintain the stability and steerability of your vehicle especially on slippery road surfaces such as snow or ice covered roads and gravel roads The system operates by detecting and controlling wheel spin The system borrows many of the electronic and mechanical elements already present in the Anti lock Braking System ABS Wheel speed sensors allow excess rear wheel spin to be detected by the Traction Control portion of the ABS computer Any excessive wheel spin is controlled by automatically applying and releasing the rear brakes in conjunction with engine torque reductions The Traction Control system will allow your vehicle to make better use of available traction on slippery surfaces while you are trying to accelerate or while your foot is on the accelerator pedal The system is a driver aid which makes your vehicle easier to handle primarily on snow and ice covered roads During Traction Control operation the traction control active light will n illuminate If your vehicle is equipped with a message center a message will display during Traction Control operation You may hear an electric motor type of sound coming from the engine compartment and the engine will not rev up when you push further on the accelerator This is normal system behavior and should be no reason for concern 152 Driving The Traction Control switch located above the radio illuminates when the system is off The Traction Control syst
223. ulbs 4 Disconnect the electrical connector from the bulb by pulling it straight off 5 Rotate the bulb counterclockwise and remove from the lamp assembly Install the new bulb in reverse order Replacing tail lamp brake rear turn signal lamp bulbs The tail lamp the brake lamp and the turn signal lamp bulbs are located in the tail lamp assembly Follow the same steps to replace either bulb 1 Make sure headlamp switch is in OFF position then open the trunk 2 Carefully remove fasteners around the lamp area and then remove the interior trunk trim 3 Disconnect the electrical grommet by pulling it straight off of the lamp assembly 4 Remove three nut and washer assemblies and the lamp assembly from the vehicle 5 Remove the bulb socket by rotating it counterclockwise then pulling it out of the lamp assembly 6 Pull the bulb straight from the socket Install the new bulb in reverse order 39 Lights Replacing backup bulbs The backup lamp is located in the tail lamp assembly Follow the same steps to replace either bulb 1 Make sure headlamp switch is in OFF position then open the trunk 2 Carefully remove fasteners around the lamp area then remove the interior trunk trim 3 Disconnect the electrical connector by pulling it straight off of the lamp assembly 4 Remove the three nut and washer assemblies and the lamp assembly from the
224. utomatic shut off points on the fuel pumps at service stations e Variations in top off procedure from one fill up to another e Rounding of the displayed values to the nearest gallon 0 1 liter 1 Drive the vehicle at least 5 miles 8 km with the speed control system engaged to display a stabilized average 2 Record the highway fuel economy for future reference It is important to press the RESET control after setting the speed control to get accurate highway fuel economy readings 58 Driver Controls Instantaneous fuel economy Select this function from the INFO menu to display your instantaneous fuel economy This will display your MPG M LEL fuel economy as a Bar Graph gooo m 000 0 ranging from W poor economy to excellent economy Your vehicle must be moving to calculate instantaneous fuel economy When your vehicle is not moving this function shows W one or no bars illuminated Instantaneous fuel economy cannot be reset Fuel Used Select this function from the INFO menu to display the fuel used since VVV V Z last reset The information displayed XXX X GALS USED will be in gallons or liters OOO00 m 800 0 depending on English metric mode state Trip elapsed drive time Select this function from the INFO menu to display a timer Trip TIME XX XX XX elapsed drive time will only dae oi TA accumulate time when the ignition OO0000 m 800 0 is in the Run Start position To operate the Trip E
225. vehicle 5 Remove the bulb socket by rotating it counterclockwise then pulling it out of the lamp assembly 6 Pull the bulb straight from the socket Install the new bulb in reverse order Replacing rear sidemarker lamp bulbs 1 Make sure the headlamp switch is in the OFF position and locate the sidemarker on the rear bumper fascia 2 Install a flathead screwdriver between the rear of the sidemarker lens and the bumper fascia 3 Push the screwdriver to the front of the vehicle and then slide it towards you to pop out the lens cover 4 Carefully pull the bulb straight out of socket Install the new bulb in reverse order 40 Lights Replacing high mount brake lamp bulbs 1 Make sure the headlamp switch is in the OFF position and then open the trunk 2 Inside trunk pull the trim panel straight off of the underside of the trunk lid 3 Locate the lighting assembly and push the release tab to access the bulb socket 4 Carefully pull the bulb straight out of socket Install the new bulb in reverse order Replacing license plate lamp bulbs 1 Make sure the headlamp switch is in the OFF position then remove the two screws and the license plate lamp assembly 2 Remove bulb socket by turning counterclockwise 3 Carefully pull the bulb out from the socket Install new bulb s in reverse order 41 Driver Controls MULTI FUNCTION LEVER Windshield wiper For intermittent oper
226. vel until it reaches the range between the MIN and MAX lines Be sure to put the cap back on the reservoir BRAKE CLUTCH FLUID Brake and clutch systems are supplied from the same reservoir The fluid level will drop slowly as the brakes wear and will rise when the brake components are replaced Fluid levels between the MIN and MAX lines are within the normal operating range there is no need to add fluid If the fluid levels are outside of the normal operating range the performance of your brake system could be compromised seek service from your authorized dealer immediately 225 Maintenance and Specifications TRANSMISSION FLUID Checking automatic transmission fluid The 5R55S transmission does not have a transmission fluid dipstick Refer to your scheduled maintenance information for scheduled intervals for fluid checks and changes Your transmission does not consume fluid However the fluid level should be checked if the transmission is not working properly i e if the transmission slips or shifts slowly or if you notice some sign of fluid leakage Transmission fluid should be checked and if required fluid should be added by an authorized dealer Before adding any fluid make sure the correct type is used Use only MERCON V automatic transmission fluid The type of fluid used is indicated on the transmission fluid pan extension housing and also in the Lubricant specifications
227. weight capacity of the vehicle or of the front or rear axle GVWR or GAWR as indicated on the Safety Compliance Certification label Consult your authorized dealer for specific weight information e The Federal Communications Commission FCC and Canadian Radio Telecommunications Commission CRTC regulate the use of mobile communications systems such as two way radios telephones and theft alarms that are equipped with radio transmitters Any such equipment installed in your vehicle should comply with FCC or CRTC regulations and should be installed only by a qualified service technician e Mobile communications systems may harm the operation of your vehicle particularly if they are not properly designed for automotive use e To avoid interference with other vehicle functions such as anti lock braking systems amateur radio users who install radios and antennas onto their vehicle should not locate the Amateur Radio Antennas in the area of the driver s side hood e Electrical or electronic accessories or components that are added to the vehicle by the authorized dealer or the owner may adversely affect battery performance and durability 240 A ACCeSSOLY delay sirsesesmiireyi 45 Air cleaner filter 228 Airbag supplemental restraint SYSTEM a neea E 97 105 and child safety seats 99 description 97 105 disposal ccccccccccccceeesseeeeeees 107 driver airbag cc 99 106 indicator light
228. with a lap belt only It is best to use a booster seat with lap shoulder belts in the back seat the safest place for children to ride Move a child to a different seating location if the shoulder belt does not stay positioned on the shoulder during use Follow all instructions provided by the manufacturer of the booster seat Never put the shoulder belt under a child s arm or behind the back because it eliminates the protection for the upper part of the body and may increase the risk of injury or death in a collision 111 Seating and Safety Restraints Never use pillows books or towels to boost a child They can slide around and increase the likelihood of injury or death in a collision SAFETY SEATS FOR CHILDREN Child and infant or child safety seats Use a safety seat that is recommended for the size and weight of the child Carefully follow all of the manufacturer s instructions with the safety seat you put in your vehicle If you do not install and use the safety seat properly the child may be injured in a sudden stop or collision When installing a child safety seat e Review and follow the information presented in the Airbag supplemental restraint system SRS section in this chapter e Use the correct safety belt buckle for that seating position the buckle closest to the direction the tongue is coming from Insert the belt tongue into the proper buckle until you hear a snap and feel it latch Make sure t
229. y even if no symptoms are immediately apparent The toxic effects of fuel may not be visible for hours e Avoid inhaling fuel vapors Inhaling too much fuel vapor of any kind can lead to eye and respiratory tract irritation In severe cases excessive or prolonged breathing of fuel vapor can cause serious illness and permanent injury e Avoid getting fuel liquid in your eyes If fuel is splashed in the eyes remove contact lenses if worn flush with water for 15 minutes and seek medical attention Failure to seek proper medical attention could lead to permanent injury e Fuels can also be harmful if absorbed through the skin If fuel is splashed on the skin and or clothing promptly remove contaminated clothing and wash skin thoroughly with soap and water Repeated or prolonged skin contact with fuel liquid or vapor causes skin irritation e Be particularly careful if you are taking Antabuse or other forms of disulfiram for the treatment of alcoholism Breathing gasoline vapors or skin contact could cause an adverse reaction In sensitive individuals serious personal injury or sickness may result If fuel is splashed on the skin promptly wash skin thoroughly with soap and water Consult a physician immediately if you experience an adverse reaction When refueling always shut the engine off and never allow sparks or open flames near the filler neck Never smoke while refueling Fuel vapor is extremely hazardous under certain conditio
230. y belts refer to Interior in the Cleaning chapter Safety belt warning light and indicator chime A The safety belt warning light illuminates in the instrument cluster and a chime sounds to remind the occupants to fasten their safety belts 91 Seating and Safety Restraints Conditions of operation The driver s or front The safety belt warning light passenger s safety belt is not illuminates1 2 minutes and the buckled before the ignition warning chime sounds 4 8 seconds switch is turned to the ON position The driver s or front The safety belt warning light and passenger s safety belt is warning chime turn off buckled while the indicator light is illuminated and the warning chime is sounding The driver s or front The safety belt warning light and passenger s safety belt is indicator chime will remain off buckled before the ignition switch is turned to the ON position BeltMinder The BeltMinder feature is a supplemental warning to the safety belt warning function This feature provides additional reminders by intermittently sounding a chime and illuminating the safety belt warning light in the instrument cluster when the driver s and front passenger s safety belt is unbuckled The BeltMinder feature uses information from the front passenger sensing system to determine if a front seat passenger is present and therefore potentially in need of a warning To avoid activating the BeltMinder fe
231. your vehicle must be serviced while you are traveling or living in Central America the Caribbean or the Middle East contact the nearest authorized dealer If the authorized dealer cannot help you write or call FORD MOTOR COMPANY WORLDWIDE DIRECT MARKET OPERATIONS 1555 Fairlane Drive Fairlane Business Park 3 Allen Park Michigan 48101 U S A Telephone 813 594 4857 FAX 313 390 0804 If you are in another foreign country contact the nearest authorized dealer If the authorized dealer employees cannot help you they can direct you to the nearest Ford affiliate office If you buy your vehicle in North America and then relocate outside of the U S or Canada register your vehicle identification number VIN and new address with Ford Motor Company Worldwide Direct Market Operations Customers in the U S should call 1 800 392 3673 ORDERING ADDITIONAL OWNER S LITERATURE To order the publications in this portfolio contact Helm Incorporated at HELM INCORPORATED P O Box 07150 Detroit Michigan 48207 187 Customer Assistance Or call For a free publication catalog order toll free 1 800 782 4356 Monday Friday 8 00 a m 6 00 p m EST Helm Incorporated can also be reached by their website www helminc com Citems in this catalog may be purchased by credit card check or money order Obtaining a French owner s guide French Owner s Guides can be obtained from your authorized dealer or by writing to
232. ystem will turn off the passenger seat side airbag if the seat is empty The airbag was designed to inflate between the door panel and occupant to further enhance the protection provided to occupants in side impact collisions The airbag SRS is designed to activate when the vehicle sustains lateral deceleration sufficient to cause the sensors to initiate airbag inflation The fact that the airbags did not inflate in a collision does not mean that something is wrong with the system Rather it means the forces were not of the type sufficient to cause activation Side airbags are designed to inflate in side impact collisions not roll over rear impact frontal or near frontal collisions unless the collision causes sufficient lateral deceleration 106 Seating and Safety Restraints Several air bag system components get hot after inflation Do not touch them after inflation If the side airbag has deployed the airbag will not function again The side airbag system including the seat must be inspected and serviced by an authorized dealer If the airbag is not replaced the unrepaired area will increase the risk of injury in a collision Determining if the system is operational The SRS uses a readiness light in the instrument cluster or a tone to indicate the condition of the system Refer to Airbag readiness section in the Instrument Cluster chapter Routine maintenance of the airbag is not required A difficulty with the syste

Ford 2006 Mustang Automobile User Manual

Contents

Download Pdf Manuals

Related Search

Related Contents