Home

Fluke PM6685 Outdoor Timer User Manual

1. 1 Park the tractor on a smooth level surface such as a concrete floor Disengage the PTO engage the parking brake turn off the engine and remove the ignition key 2 Lower the mower deck to its lowest cutting position and remove the mower deck guards A WARNING Use extreme caution when rotating the idler arm with the breaker bar due to the increased tension in the spring as the idler arm is being rotated Injury may result if the breaker bar is prematurely released while the spring is under tension 3 For 61 Decks Using a 1 2 breaker bar place the square end in the square hole located in the end of the idler arm A Figures 44 Carefully rotate the breaker bar COUNTER CLOCKWISE which will relieve the tension on the belt exerted from the idler arm For 72 Decks Using the 3 4 combination wrench place the box end on the nut A Figure 44 that secures the idler pulley located at the end of the idler arm Carefully roate the wrench CLOCKWISE which will relieve the tension on the belt exerted from the idler arm 4 Slide the drive belt over the edge of the stationary idler pulley B Carefully release the tension on the breaker bar or the combination wrench 5 Remove the old belt and replace with a new one Make sure the V side of the belt runs in the pulley grooves Figure 45 6 For 61 Decks Install the drive belt on the PTO pulley the spindle pulleys and all idler pulleys except the stationary pulley B
2. Cut tall grass at maximum cutting height during first pass Cut grass with discharge pointing toward previously cut area Tighten to 70 ft lbs 94 N m Check and replace as necessary Remove sharpen and balance blades See Maintenance Section Reinstall Correctly Repair or replace Replace with correct belt Repair or replace as needed Replace drive belt Locate amp repair damaged wire See PTO Clutch Adjustment section Recharge battery and check alternator See Battery Maintenance section 45 Troubleshooting TROUBLESHOOTING COMMON CUTTING PROBLEMS PROBLEM CAUSE REMEDY Streaking 1 Blades are not sharp x adab your Vina 2 Blades are worn down too far y Heplace your blades 3 Always mow at FULL throttle 3 Engine speed is too slow Slow 4 Ground speed is too fast SSW COW 5 Clean out the mower aasyal 5 Deck is plugged with grass TL LU Fal h 6 Overlap you cutting rows 6 Not overlapping cutting rows enough A 7 When turning your effective cutting width 7 Not overlapping enough when turning decreases overlap more when turning Lawn is uneven or bumpy 2M Jeck ina helene 1 Roll or level the lawn bd eck cutting height is set too 2 Raise the cutting height 3 Ground speed is too fast Sow HOW 4 Deck is not levelled correctly 4 Gorrectly level me geek 5 Tire pressure is low or uneven S CNEEK And Miate M
3. Do not attach towed equipment except at the hitch point Follow the manufacturer s recommendations for weight limit for towed equipment and towing on slopes See attaching a trailer under OPERATION Never allow children or others in or on towed equipment On slopes the weight of the towed equipment may cause loss of traction and loss of control Travel slowly and allow extra distance to stop Do not shift to neutral and coast down hill CHILDREN Tragic accidents can occur if the operator is not alert to the presence of children Children are often attracted to the unit and the mowing activity Never assume that children will remain where you last saw them 1 Keep children out of the mowing area and under the watchful care of another responsible adult 2 Be alert and turn unit off if children enter the area 3 4 Before and during reverse operation look behind and down for small children Never carry children even with the blade s off They may fall off and be seriously injured or interfere with safe unit operation Children who have been given rides in the past may suddenly appear in the mowing area for another ride and be run over or backed over by the machine Never allow children to operate the unit Use extra care when approaching blind corners shrubs trees or other objects that may obscure vision Operator Safety EMISSIONS 1 Engine exhaust from this product contain
4. Model FX751V on Axle Horsepower 27 3600 rpm Displacement 52 0 Cu in 852 cc Electrical System 12 Volt 15 amp Alternator Battery 340 CCA DIMENSIONS Oil Capacity 2 0 US qt 1 9 L w Filter Overall Length 79 201 cm Overall Width 62 157 cm s Height 68 173 cm k 28 HP Briggs amp Stratton Weight apx 1175 Ibs 534 kg Make Briggs amp Stratton Model 541777 0110 E1 Horsepower 28 3600 rpm Displacement 54 88 Cu in 896 cc Electrical System 12 Volt 20 amp Alternator Battery 340 CCA Oil Capacity 2 4 qt 2 3 L w Filter Engine Power Rating Information The gross power rating for individual gas engine models is labeled in accordance with SAE Society of Automotive Engineers code J1940 Small Engine Power amp Torque Rating Procedure and rating performance has been obtained and corrected in accordance with SAE J1995 Revision 2002 05 Torque values are derived at 3060 RPM horsepower values are derived at 3600 RPM Actual gross engine power will be lower and is affected by among other things ambient operating conditions and engine to engine variability Given both the wide array of products on which engines are placed and the variety of environmental issues applicable to operating the equipment the gas engine will not develop the rated gross power when used in a given piece of power equipment actual on site or net power This difference is due to a variety of factors including but not limited to acc
5. gradually open the choke push knob down fully Reduce to half throttle speed and allow to warm up Warm up the engine by running it for at least a minute before engaging the PTO switch or driving the rider 5 After warming the engine ALWAYS operate the unit at FULL THROTTLE when mowing In the event of an emergency the engine can be stopped by simply turning the ignition switch to STOP Use this method only in emergency situations For normal engine shut down follow the procedure given in STOPPING THE RIDER Stopping the Rider 1 Returning the ground speed control levers to the middle position will stop rider movement Pivot the levers outward and lock them in NEUTRAL 2 Disengage the PTO by pushing down on the PTO switch 3 Engage the parking brake by pulling the handle up until it locks into position 4 Move the throttle control to mid throttle position and turn the ignition key to OFF Remove the key 20 Pushing the Rider By Hand NOTICE DO NOT TOW RIDER Towing the units will cause hydraulic pump and wheel motor damage Do not use another vehicle to push or pull this unit 1 Disengage the PTO engage the parking brake turn the ignition OFF and remove the key 2 Lift the seat plate to gain access to the hydraulic pumps 3 To disengage the pumps free wheel position turn the hydraulic release valves A Figure 9 located on the pumps COUNTER CLOCKWISE a maximum of 2 full turns 4 Disengage the
6. mechanism If dirt or debris is found it should be removed 2 Check to make sure the retraction mechanism retracts easily and completely Check for damage to any part of the seat belt such as nicks cuts loose stitching or fraying Check that the buckle and latch operate properly and that the latch plate is not excessively worn deformed or the buckle is damaged or cracked The seat belt should latch and release easily LLL m i Safety Decals This unit has been designed and manufactured to provide you with the safety and reliability you would expect from an industry leader in outdoor power equipment manufacturing Although reading this manual and the safety instructions it contains will provide you with the necessary basic knowledge to operate this equipment safely and effectively we have placed several safety labels on the unit to remind you of this important information while you are operating your unit All DANGER WARNING CAUTION and instructional messages on your rider and mower should be carefully read and obeyed Personal bodily injury can result when these instructions are not followed The information is for your safety and it is important The safety decals below are on your rider and mower If any of these decals are lost or damaged replace them at once See your local dealer for replacements These labels are easily applied and will act as a constant visual reminder to you and others who may
7. Figure 44 Carefully rotate the breaker bar COUNTER CLOCKWISE and install the belt on the stationary idler pulley B Carefully release the tension on the breaker bar For 72 Decks Install the drive belt on the PTO pulley the spindle pulleys and all idler pulleys except the stationary pulley B Figure 44 Carefully rotate the combination wrench CLOCKWISE and install the belt on the stationary idler pulley B Carefully release the tension on the combination wrench 7 Reinstall the mower deck guards 8 Run the mower under no load condition for about 5 minutes to break in the new belt Regular Maintenance 72 Decks Figure 44 Mower PTO Belt A Idler Arm B Stationary Idler Pulley C Nut 72 Decks Figure 45 Mower PTO Belt Routing A Spindle Pulley B PTO Drive Belt C Spring loaded Idler Pulley D Stationary Idler Pulley 37 Regular Maintenance Check the Mower Belt Idler Tensioner Spring Length 1 Park the machine on a smooth level surface such as a concrete floor Disengage the PTO engage the parking brake turn off the engine and remove the ignition key 2 Lower the mower deck to its lowest cutting position 3 Measure the coil length of the mower belt tensioner spring A Figure 46 The measurement should equal 7 1 4 18 42 cm If the measurement does not equal 1 1 4 18 42 cm adjust the anchor eyebolt B Adjusti
8. Gasoline if permitted to stand unused for extended periods 30 days or more may develop gummy deposits which can adversely affect the engine carburetor and cause engine malfunction To avoid this condition add a gasoline stabilizer to the fuel tank and run the engine a few minutes or drain all fuel from the unit before placing it in storage Starting After Long Term Storage Before starting the unit after it has been stored for a long period of time perform the following steps 1 Remove any blocks from under the unit 2 Install the battery if it was removed 3 Unplug the exhaust outlet and air cleaner 4 Fill the fuel tank with fresh gasoline See engine manual for recommendations 5 See engine owner s manual and follow all instructions for preparing engine after storage 6 Check crankcase oil level and add proper oil if necessary If any condensation has developed during storage drain crankcase oil and refill 7 Inflate tires to proper pressure Check fluid levels 8 Start the engine and let it run slowly DO NOT run at high speed immediately after starting Be sure to run engine only outdoors or in well ventilated area 43 Troubleshooting Troubleshooting Troubleshooting Chart While normal care and regular maintenance will extend the life of your equipment prolonged or constant use may eventually require that service be performed to allow it to continue operating properly The troubleshooting guide
9. ROLL BAR PROTECTIVE STRUCTURE A WARNING Failure to properly inspect and maintain the ROLL BAR protective structure can cause serious injury or death A ROLL BAR like any other safety device needs to be periodically inspected to verify that the integrity of the device has not been compromised through normal machine use misuse age degradation modifications or a roll over Operator Safety To maintain operator roll over protection and roll bar effectiveness f a ROLL BAR becomes damaged for any reason such as a collision roll over or impact the ROLL BAR must be replaced Small undetectable cracks can reduce the effectiveness of the ROLL BAR Never weld straighten or repair the ROLL BAR Never alter the ROLL BAR by welding anything to it or by drilling additional holes BEFORE FIRST TIME USE Inspect the ROLL BAR structure and mounting hardware for 1 Check to make sure the machine GVW Gross Vehicle Weight including attachments restrained payload fuel and operator is not in excess of the maximum weight specified on the ROLL BAR label 2 Make sure there isn t any missing damaged or loose mounting hardware 3 Make sure the ROLL BAR has been correctly and completely installed EVERY 100 HOURS Inspect the ROLL BAR structure and mounting hardware for 1 Any cracks in the structure structural members and or welds 2 Significant corrosion on any part of the ROLL BAR st
10. SHALL NOT BE LIABLE TO THE PURCHASER OR TO ANYONE CLAIMING UNDER THE PURCHASER FOR ANY OTHER OBLIGATIONS OR LIABILITIES INCLUDING BUT NOT LIMITED TO OBLIGATIONS OR LIABILITIES ARISING OUT OF BREACH OF CONTRACT OR WARRANTY NEGLIGENCE OR OTHER TORT OR ANY THEORY OF STRICT LIABILITY WITH RESPECT TO SNAPPER PRO PRODUCTS OR SNAPPER PRO ACTS OR OMISSIONS OR OTHERWISE It is the express wish of the parties that this agreement and any related documents be drafted in English Il est la volont expresse des parties que cette convention et tous les documents s y rattachent soient r dig s en anglais SNAPPER Product Specifications ENGINE 25 HP Kawasaki Make Kawasaki Model FH721V Oil Capacity 2 0 Qt 1 9 L w Filter 26 HP Kawasaki Make Kawasaki Model FX730V Oil Capacity 2 2 Qt 2 1 L w Filter 27 HP Kohler Make Kohler Model CV740S Oil Capacity 2 2 Qt 2 1 L w Filter 27 HP Kawasaki Make Kawasaki Model FX751V Oil Capacity 2 0 Qt 1 9 L w Filter 28 HP Briggs amp Stratton Make Briggs amp Stratton Model 541771 0110 E1 Oil Capacity 2 4 Qt 2 25 L w Filter 32 HP Briggs amp Stratton Make Briggs amp Stratton Model 543771 0120 E1 Oil Capacity 2 4 Qt 2 25 L w Filter Briggs amp Stratton Yard Power Products Group 5375 North Main Street Munnsville NY 13409 800 933 6175 www SnapperPro com O PERATOR S MANUAL 200X Series Zero Turn Riding Mower Common Service Pa
11. SnapperPro com Deck Rod Timing Adjustment 1 Park the machine on a flat level surface Disengage the PTO engage the parking brake turn off the engine and remove the ignition key Rear tires must be inflated to 15 psi 1 03 bar front tires to 25 psi 1 72 bar To check the lift rod timing measure and record the distance between the lift pivots and the rod pivots Repeat for other side of unit See Figure 38 If the measurements for the rods are equal no further adjustment is required If the measurements are NOT equal greater than 1 8 3 17 mm difference adjustment is required continue with Step 4 Lock the deck lift pedal in the 5 12 7 cm position Remove the cutting height adjustment pin and lower the mower deck To ensure that the deck is in the lowest position push the pedal by hand towards the rear of the unit and install the height adjustment pin in the 3 7 6 cm position to hold in place Block up the mower deck until all hanger chains are slack Refer to Figure 40 See Figure 39 To adjust the lift rod loosen the jam nut on the front clevis then remove the 1 2 clevis pin fastening the clevis to the lift pivot arm Turn the clevis clockwise to shorten the distance between the rod pivots or counterclockwise to lengthen the distance between the rod pivots Reinstall the clevis on the lift pivot arm and secure with the 1 2 clevis pin previously removed Tighten the jam nut again
12. Straight forward travel takes practice If necessary top speed can be balance adjusted see the Speed Balancing Adjustment in the Adjustments section near the back of this manual Operation Smooth Travel The lever controls of the Zero Turn rider are responsive The BEST method of handling the ground speed control levers is in three steps as shown in Figure 10 FIRST place your hands onto the levers as shown SECOND to go forward gradually push the levers forward with your palms THIRD to speed up move the levers farther forward To slow down smoothly slowly move the levers toward neutral Figure 10 Move Control Levers Gradually Reverse Travel Practice LOOK DOWN amp BEHIND then gradually move both ground speed control levers evenly BACK from neutral Slow down and repeat NOTE Practice backing up for several minutes before attempting to do so near objects The rider turns sharply in reverse as well as forward and backing up straight takes practice Forward Travel Reverse Travel Figure 11 Forward Travel Figure 12 Reverse Travel 21 Operation Practice Turning Around a Corner While traveling forward allow one handle to gradually return back toward neutral Repeat several times NOTE To prevent pivoting directly on the tire tread it is best to keep both wheels going at lea
13. an n 1 tt A NT E 1 Ka ua uz tt xA bl ERE RE ka n un un n ma m weet Gu Ts a Tn Gs T Tn T E m F ma u u u Thrown Objects This unit has spinning mower blades These blades can pick up and throw debris that could seriously injure a bystander Be sure to clean up the area to be mowed and remove objects that could be thrown by the blade BEFORE you start mowing Do not operate this unit without the entire grass catcher or discharge guard deflector in place Also do not allow anyone in the area while the unit is running If someone does enter the area shut the unit off immediately until they leave Slope Operation Operation on slopes can be dangerous Using the unit on a slope that is too steep where you do not have adequate wheel traction and control can cause sliding loss of steering control and possible rollover You should not operate on a slope greater than a 5 4 foot rise over a 20 foot length 15 degrees Always mow across slopes not up and down to maintain traction on the wheels and avoid sudden turns or rapid speed changes Reduce speed and use extreme caution on ALL slopes Also note that the surface condition you are on can greatly impact your ability to safely operate this machine Operating on wet or slippery slopes can cause sliding and loss of steering and control Do not operate on slopes that are slippery wet or have soft soil conditions If you feel unsure about operating the unit on a slo
14. bar raised Lower the roll bar only when necessary such as to temporarily clear a low overhanging obstacle and NEVER remove it Do NOT use the seat belt when the roll bar is down Raise the roll bar as soon as clearance permits Overhead Obstacles Check for overhead clearances before driving under any objects Do not allow the roll bar to contact low overhanging obstacles such as tree branches and guide wires Enclosed Areas Only operate this unit outdoors and away from unventilated areas such as inside garages or enclosed trailers The engine emits poisonous carbon monoxide gas and prolonged exposure in an enclosed area can result in serious injury or death Operator Safety Fuel and Maintenance Always disengage all drives shutoff the engine and remove the key before doing any cleaning refueling or servicing Gasoline and its vapors are extremely flammable Do not smoke while operating or refueling Do not add fuel while engine is hot or running Allow engine to cool for at least 3 minutes prior to adding fuel Do not add fuel indoors in an enclosed trailer garage or any other enclosed area that is not well ventilated Gasoline spills should be cleaned up promptly and before operation begins Gasoline should be stored only in sealed containers approved for fuel Proper maintenance is critical to the safety and performance of your unit Keep the unit free of grass leaves
15. battery well during charging A voltmeter can be used to determine condition of battery When engine is off the voltmeter shows battery voltage which should be 12 volts When engine is running the voltmeter shows voltage of charging circuit which normally is 13 to 14 volts A dead battery or one too weak to start the engine may not mean the battery needs to be replaced For example it may mean that the alternator is not charging the battery properly If there is any doubt about the cause of the problem see your dealer If you need to replace the battery follow the steps under Cleaning the Battery amp Cables in the Regular Maintenance Section Charging a Completely Discharged Battery 1 Be aware of all the safety precautions you should observe during the charging operation If you are unfamiliar with the use of a battery charger and hydrometer have the battery serviced by your dealer 2 Add distilled water sufficient to cover the plate fill to the proper level near the end of the charge If the battery is extremely cold allow it to warm before adding water because the water level will rise as it warms Also an extremely cold battery will not accept a normal charge until it becomes warm 3 Always unplug or turn the charger off before attaching or removing the clamp connections 4 Carefully attach the clamps to the battery in proper polarity usually red to positive and black to negative 5 While charging pe
16. engine 2 Move the ground speed control levers into the operating position pull levers rearward and release 3 Move the ground speed control levers out towards the neutral position If the levers do not align with the notches in the neutral lock plate it is necessary to adjust the adjustment linkage rod B Figure 37 A WARNING To avoid serious injury perform adjustments only with engine stopped key removed and tractor on level ground Adjustment 1 Pull the ground speed control lever rearward and release to check position If the ground speed control lever does not align itself with the notch in the neutral plate then move the set collar A forward or back on the adjustment linkage rod B until the speed control lever aligns with the notch Retighten the set collar 2 Make sure that the neutral return bushing D is seated correctly in the spring stop plate E 3 Pull the ground speed control lever rearward and release to check position again Adjust as necessary to align the ground speed control levers with the notches in the neutral lock plate It is important to note that after every adjustment of the neutral return rod the lever must be pulled rearward and released to properly check the neutral position 34 Figure 37 Neutral Return Spring Adjustment A Set Collar B Adjustment Linkage Rod C Neutral Return Spring D Neutral Return Bushing E Spring Stop Plate www
17. on both batteries 4 Connect positive cable to positive post of discharged battery wired to starter or solenoid 5 Connect the other end of same cable to same post marked positive on booster battery 6 Connect the second cable negative to other post of booster battery 7 Make final connection on engine block of stalled vehicle away from battery Do not lean over batteries 8 Start the engine of the vehicle with the booster battery Wait a few minutes then attempt to start the engine of the vehicle with the discharged battery 9 f the vehicle does not start after cranking for thirty seconds STOP PROCEDURE More than thirty seconds seldom starts the engine unless some mechanical adjustment is made 10 After starting allow the engine to return to idle speed Remove the cable connection at the engine or frame Then remove the other end of the same cable from the booster battery 11 Remove the other cable by disconnecting at the discharged battery first and then disconnect the opposite end from the booster battery 12 Discard the damp cloths that were placed over the battery vent caps 41 Regular Maintenance THIS HOOK UP FOR NEGATIVE GROUND VEHICLES To Starter O Switch To Starter Switch Jumper Cable Starting Vehicle Battery To Ground Discharged Vehicle Battery MAKE CERTAIN VEHICLES DO NOT TOUCH Figure 49 Jump Starting A WARNING Any procedure other than the precedin
18. parking brake The tractor can now be pushed by hand 5 After moving the tractor re engage the pumps drive position by turning the release valves CLOCKWISE and tighten to 80 120 in lbs of torque Sy Figure 9 Hydraulic System By Pass A Hydraulic Release Valve left hand pump shown www SnapperPro com Zero Turn Driving Practice The lever controls of the Zero Turn rider are responsive and learning to gain a smooth and efficient control of the rider s forward reverse and turning movements will take some practice Spending some time going through the maneuvers shown and becoming familiar with how the unit accelerates travels and steers before you begin mowing is absolutely essential to getting the most out of the Zero Turn rider Locate a smooth flat area of your lawn one with plenty of room to maneuver Clear the area of objects people and animals before you begin Operate the unit at mid throttle during this practice session ALWAYS operate at full throttle when mowing and turn slowly to prevent tire slippage and damage to your lawn We suggest you begin with the Smooth Travel procedure to the right and then advance through the forward reverse and turning maneuvers You must release the parking brake prior to moving the control levers inward Forward Travel Practice Gradually move both ground speed control levers evenly FORWARD from neutral Slow down and repeat NOTE
19. protects the grass from heat damage and other problems However allowing grass to grow too high can cause thin turf and additional problems Cutting off too much at one time shocks the plant s growth system and weakens the grass plants A good rule of thumb is the 1 3 rule to cut no more than one third of the grass height and never more than 1 inch at a time The amount of grass you are able to cut in one pass is also effected by the type of mowing system you are using for example broadcasting with side discharge decks can process a much larger volume of grass than mulching does Operation rit M lif i uada a L vdl V MAMMA Figure 16 Proper Cutting Height Tall Grass Requires Incremental Cutting For extremely tall grass set the cutting height at maximum for the first pass and then reset it to the desired height and mow a second or third time Don t cover the grass surface with a heavy layer of clippings Consider using a grass collection system and starting a compost pile Cut Here On First Pass Cut Here On Second QA C P Mu ji N E lil M MU Figure 17 Incremental Cutting 23 Operation When and How Often to Mow The time of day and condition of the grass greatly affect the results you ll get when mowing For the best results follow these guidelines 1 Mow when the grass is between three and five inches high 2 Mow with sharp blades Short clippings of grass one
20. that is located on the engine deck on the right hand side of the frame Place the drain hose down through the hole E in the engine deck 3 Place a small pan under the oil drain hose to catch the oil Using the appropriate tools remove the cap B from the oil drain hose A and drain the engine oil into the pan 4 After draining replace the cap and wipe up any spilled oil Reinstall the oil drain hose into the cable clamp to retain the hose during normal operation 5 Place an absorbent shop cloth under the engine oil filter Remove the engine oil filter and replace with a new one 6 Remove the shop cloth and wipe up any spilled oil NOOO co n Inspect Muffler and Spark Arrester Inspect the muffler for cracks corrosion or other damage Remove the spark arrester if equipped and inspect for damage or carbon blockage If replacement parts are required make sure to use only original equipment replacement parts Engine Maintenance Refer to engine owner s manual for all engine maintenance procedures and recommendations Regular Maintenance 4 WARNING Gasoline is highly flammable and must be handled with care Never fill the tank when the engine is still hot from recent operation Do not allow open flame smoking or matches in the area Avoid over filling and wipe up any spills Do not remove fuel filter when engine is hot as spilled gasoline may ignite DO NOT spread hose clamps further than necessary Ensure cl
21. the Mower Blades 30 Ground Speed Control Lever Adjustment 32 Speed Balancing Adjustment 32 Neutral Adjustment 33 Parking Brake Adjustment 33 Return to Neutral Adjustment 34 Deck Rod Timing Adjustment 35 Deck Leveling Adjustment 36 Mower Belt Replacemen t 37 Hydraulic Pump Drive Belt Replacement 39 Battery Maintenancoe 40 Battery Service 2 41 SIOIage ouo NEN eene 43 Starting After Long Term Storage 43 Troubleshooting 44 Troubleshooting the Rider 44 Troubleshooting the Mower 45 Troubleshooting Common Cutting Problems 46 sl up m 47 Slope Identification Guide 48 NOTE In this manual left and right are referred to as seen from the operating position Operator Safety Read the Manual The operator s manual contains important safety information you need to be aware of BEFORE you operate your unit as well as DURING operation Safe operating te
22. until the chains are tight and tighten the nuts See Figure 41 6 Remove all 2 x 4 blocks from under the mower deck 7 For your safety DO NOT handle mower blades with bare hands Position the outside mower blades so that they face front to back Figure 42 8 Measure from the front tip of the blade from the cutting edge to the ground Measure from the rear tip of the blade from the cutting edge to the ground Repeat this process for the other side of the machine The front and back measurements should be 4 10 2 cm If the measurements are greater than 1 8 3 17 mm of what they should be adjust the deck height until they are correct Fine Adjustment 1 Loosen the jam nut A Figure 43 and turn the fine adjustment bolt B to adjust the deck height until the front measurements equals 4 10 2 cm Turn the bolt CLOCKWISE to raise the deck COUNTER CLOCKWISE to lower the deck 2 Position the outside mower blades so they face front to back 3 Remeasure the front tip of the blade from the cutting edge to the ground Measure the rear tip of the blade from the cutting edge to the ground Repeat the process for the other side of machine 4 Once the measurement equals 4 10 2 cm retighten the jam nut 36 Figure 43 Fine Adjustment A Jam Nut B Fine Adjustment Bolt www SnapperPro com Mower Belt Replacement NOTICE To avoid damaging belts DO NOT PRY BELTS OVER PULLEYS
23. use the equipment to follow the safety instructions necessary for safe effective operation Operator Safety 4 PELIGRO A DANGER AMPUTATION AND PELIGRO DE AMPUTACI N THROWN OBJECTS Dy Y OBJETOS ARROJADOS Para evitar sufrir lesiones A PELIGRO PELIGRO DE AMPUTACI N Para evitar lesiones causadas discharge chute or entire grass catcher i place por las cuchillas mantenerse alejado del borde de la plataforma de corte wi descarga o sin el recogedor de pasto en su lugar 11 Keep unit free of grass leaves and excess oil i e Do NOT add fuel while engine is hot or running s a MONOXIDE STOP engine and allow to cool for 5 minutes prior to adding fuel gt POISONING Do NOT add fuel indoors in an enclosed trailer garage or other Do NOT operate the A DANGER AVOID FIRE HAZARD AVOID CARBON enclosed areas engine in Clean up spilled fuel unventilated arca Do NOT smoke while operating this machine sms A PELIGRO EVITE LOS PELIGROS DE INCENDIO EVITE LA Mantenga la unidad libre de pasto hojas y aceite excesivo a NO cargue combustible mientras ci motor est caliente o encendido INTOXICACI N DETENGA el motor y d jelo enfriar durante 5 minutos antes de b POR MONOXIDO cargar combustible JR DE CARBONO NO cargue combustible en espacios cerrados como remolques NO opere el motor s cocheras u otras reas
24. which then blows them down INTO the lawn These tiny particles decompose rapidly into by products your lawn can use UNDER PROPER CONDITIONS your mulching mower will virtually eliminate noticeable clippings on the lawn surface NOTE When mulching under heavy cutting conditions a rumbling sound may be present and is normal Mulching Requires EXCELLENT Mowing Conditions Mulching mowers cannot function properly if the grass is wet or if the grass is simply to high to cut Even more than normal mowing mulching requires that the grass be dry and the the appropriate amount is cut Do not use the mower as a mulching mower during the first two or three mowings in the spring The long grass blades quick growth and often wetter conditions are more suitable for broadcasting side discharging or grass bagging operation Engine Speed amp Ground Speed for Mulching Use full engine throttle matched with a slow ground speed so that clippings will be finely cut Ground speed while mulching should be HALF of the speed that would be used when broadcasting side discharging under similar conditions Since mulching requires more horsepower than broadcasting using a slower ground speed is vitally important for proper mulching operation How Much Grass to Mulch The best mulching action typically results from cutting only the top 1 2 inch to 3 4 inch of grass blade This provides short clippings which decompose properly much more quickly tha
25. 5 degree limit of stability is equal to 50 of the angle at which machine lift off occurred in static tests Actual dynamic stability may vary depending on operating conditions 5 Operator Safety Use extra care with grass catchers or other attachments These can change the stability of the unit Keep all movement on the slopes slow and gradual Do not make sudden changes in speed or direction See your authorized dealer for recommendations of available weights to improve stability ae Not OND Oo Avoid starting stopping or turning on a slope If tires lose traction i e machine stops forward motion on a slope disengage the blade s PTO and drive slow off the slope Do not turn on slopes unless necessary and then turn slowly and gradually uphill if possible Never mow down slopes Do not mow near drop offs ditches or embankments The operator could lose footing or balance or mower could suddenly turn over if a wheel is over the edge of a cliff or ditch or if an edge caves in Do not mow on wet grass Reduced footing or traction could cause sliding Do not try to stabilize the unit by putting your foot on the ground ride on units Do not mow excessively steep slopes Do not use grass catcher on steep slopes Do not mow slopes if you cannot back up them Vela EQUIPMENT RIDE ON UNITS on C Tow only with a machine that has a hitch designed for towing
26. E 3 Lock the jam nut B against the ball joint when neutral is achieved NOTE This adjustment should not be performed while the machine is running It may take several attempts to achieved neutral depending upon how much the machine creeps Parking Brake Adjustment 1 Disengage the PTO stop the engine block the front wheels remove the ignition key and engage the parking brake 2 Locate the brake spring A Figure 36 3 With the parking brake engaged measure the compressed spring length The spring should be 2 to 2 1 8 5 0 5 4 cm when compressed 4 If the spring is not within this range release the parking brake and turn the adjustment nut B to compress or release the spring 5 Engage the parking brake and remeasure the spring CAUTION Do not adjust the spring to be shorter than 1 15 16 4 9 cm when compressed This may damage the brake mechanism If this does not correct the braking problem see your Snapper Pro dealer Regular Maintenance IL ex Figure 35 Neutral Adjustment LH side shown A Adjustment Linkage Rod B Nuts 2 2 1 8 5 0 5 4cm Figure 36 Parking Brake Adjustment A Brake Spring B Adjustment Nut 33 Regular Maintenance Return To Neutral Adjustment To determine if it is necessary to adjust the neutral return perform the following steps 1 Disengage the PTO engage the parking brake and turn off the
27. OT START OR STOP ON SLOPE Checks Before Starting Check that crankcase is filled to full mark on dipstick See the engine Operator s Manual for instructions and oil recommendations Fill the fuel tank with fresh fuel Refer to engine manual for fuel recommendations Make sure all nuts bolts screws and pins are in place and tight Make sure the fuel valve is in the ON position Check the tire pressures See Check Tire Pressures Make sure that the Roll Bar is adjusted in the upright position See Raise and Lower the Roll Bar Adjust the seat position and make certain you can reach all controls from operator s position See Seat Adjustment Adjust the height of the mower deck to the desired position See Mowing Height Adjustment www SnapperPro com Check Tire Pressures Tire pressure should be checked periodically and maintained at the levels shown in the chart Note that these pressures may differ slightly from the Max Inflation stamped on the side wall of the tires The pressures shown provide proper traction improve cut quality and extend tire life Tire Pressure Front 25 psi 1 72 bar Rear 15 psi 1 03 bar Seat Adjustment See Figure 4 The seat can be adjusted forward and backward Move the lever towards the left position the seat as desired and release the lever to lock the seat into position Seat Adjustment Suspension Seat See Figure 5 In addition to th
28. SNAPPER PRO OPERATOR S MANUAL 200X Series Zero Turn Riding Mower Model Number Description 5900824 S200XKAV2561 25HP Kawasaki 61 Cut Zero Turn Riding Mower 5900825 S200XKOH2761 27HP Kohler 61 Cut Zero Turn Riding Mower 5900826 S200XKAV2761 27HP Kawasaki 61 Cut Zero Turn Riding Mower 5900827 S200XKAV2561 CAL 25HP Kawasaki 61 Cut Zero Turn Riding Mower 5900828 S200XBV3261 32HP Briggs amp Stratton 61 Cut Zero Turn Riding Mower 5900874 S200XKAV2761 S S CAL 27HP Kawasaki 61 Cut Zero Turn Riding Mower 5900882 S200XKAV2661 26HP Kawasaki 61 Cut Zero Turn Riding Mower 5900861 S200XBV2861 28HP Briggs amp Stratton 61 Cut Zero Turn Riding Mower 5900901 200ZBV3261 CAL 32HP Briggs amp Stratton 61 Cut Zero Turn Riding Mower Briggs amp Stratton Yard Power Products Grou 5375 North Main Street i Danes Munnsville NY 13409 Rev Date 06 2010 800 933 6175 TP 100 7425 D M2 SP Thank you for purchasing this quality built Snapper Pro product We re pleased that you ve placed your confidence in the Snapper Pro brand When operated and maintained according to the instructions in this manual your Snapper Pro product will provide many years of dependable service This manual contains safety information to make you aware of the hazards and risks associated with this machine and how to avoid them This machine is designed and intended to be used and maintained according to the manual and operated by trained profe
29. amps grip hoses firmly over filter after installation NOTICE Do not use gasoline containing METHANOL gasohol containing more than 1096 ethanol gasoline additives premium gasoline or white gas because engine fuel system damage could result Figure 20 Engine Oil Drain Oil Drain Hose Cap Cable Clamp Oil Filter Hole for Drain Hose MOODS A WARNING Replacement parts must be the same and installed in the same position as the orginal parts or fire could result 27 Regular Maintenance Lubrication Lubricate the unit at the locations shown in Figures 21 through 24 as well as the following lubrication points Grease front caster wheel axles amp yokes deck lift pivot blocks mower deck spindles mower deck idler arm Use grease fittings when present Disassemble parts to apply grease to moving parts when grease fittings are not installed Not all greases are compatible Red Grease p n 5022285 is recommended automotive type high temperature lithium grease may be used when this is not available Oil e control handle pivots seat plate pivots e deck lift pivots discharge chute hinge Generally all moving metal parts should be oiled where contact is made with other parts Keep oil and grease off belts and pulleys Remember to wipe fittings and surfaces clean both before and after lubrication Lubricating the Front Casters NOTE Front casters should be lubric
30. anchor tab and loosely fasten the nut Adjust the anchor eyebolt until a measurement of 8 3 8 21 2 cm is achieved from the outside if the spring hooks Tighten nut Reinstall the clutch anchor pad to the PTO clutch and secure with the hardware previously removed Reinstall the PTO drive belt 39 Regular Maintenance Battery Maintenance NOTE This unit is equipped with a maintenance free BCIU1 battery Cleaning the Battery and Cables A WARNING Be careful when handling the battery Avoid spilling electrolyte Keep flames and sparks away from the battery When removing or installing battery cables disconnect the negative cable FIRST and reconnect it LAST If not done in this order the positive terminal can be shorted to the frame by a tool 1 Disconnect the cables from the battery negative black cable first B Figure 48 2 Clean the battery terminals and cable ends with a wire brush until shiny 3 Reinstall the battery and reattach the battery cables positive red cable first A 4 Coat the cable ends and battery terminals with petroleum jelly or non conducting grease 40 Figure 48 Battery Compartment A Positive Cable amp Terminal B Negative Cable amp Terminal www SnapperPro com Battery Service Checking Battery Voltage WARNING Keep open flames and sparks away from the battery the gasses coming from it are highly explosive Ventilate the
31. and excess oil Be sure to perform the maintenance procedures listed in this manual especially periodically testing the safety system Operator Safety A Read these safety rules and follow them closely Failure to obey these rules could result in loss of control of unit severe personal injury or death to you or bystanders or damage to property or equipment This mowing deck is capable of amputating hands and feet and throwing objects The triangle 4 in text signifies important cautions or warnings which must be followed TRAINING Read understand and follow all instructions in the manual and on the unit before starting If the operator s or mechanic s can not read English itis the owner s responsibility to explain this material to them Become familiar with the safe operation of the equipment operator controls and safety signs All operators and mechanics should be trained The owner is responsible for training the users Only allow responsible adults who are familiar with the instructions to operate the unit Never let children or untrained people operate or service the equipment Local regulations may restrict the age of the operator The owner user can prevent and is responsible for accidents or injuries occurring to themselves other people or property Data indicates that operators age 60 years and above are involved in a large percentage of riding mower related inj
32. arranty you shall have read the operator s manual and you shall have completed and submitted to Snapper Pro within 20 days from the date of purchase the Snapper Pro Product Registration You must properly service and maintain your Snapper Pro product as described in the operator s manual Such routine maintenance whether performed by a dealer or by you is at your expense The Snapper Pro equipment including any defective part covered by this limited warranty must be returned to an authorized Snapper Pro dealer within the warranty period for warranty service This limited warranty extends only to equipment operated under normal conditions and in accordance with Snapper Pro instructions Warranty Start Date The limited warranty coverage begins on the day you buy your new Snapper Pro commercial mowing equipment An authorized Snapper Pro dealer will assist you in filling out a Snapper Pro Product Registration with specific information for the model you purchase and your per sonal information which must be returned to Snapper Pro Limited Warranty The limited warranty set forth below is a written guarantee by Snapper Pro during the warranty period to repair or replace parts which have a substantial defect in materials or workmanship The warranty is limited because it is for a specified period of time applies to the origi nal purchaser only and is subject to other restrictions SNAPPER PRO LIMITED WARRANTY Snapper Pro warrants in accor
33. ated annually 1 Remove the 1 4 28 bolt A Figure 24 screwed into the front caster and install a 1 4 28 grease fitting 2 Grease the front caster 3 Remove the 1 4 28 grease fitting and reinstall the 1 4 28 bolt 4 Repeat process for the other side of the machine 28 Figure 24 Front Caster amp Wheel A 1 4 28 Bolt www SnapperPro com Check Hydraulic Oil Level 1 Before removing the reservoir cap make sure the area around the reservoir cap and fill neck of the reservoir is free of dust dirt or other debris 2 Unscrew the reservoir cap B Figure 25 3 Look down the filler neck of the hydraulic oil reservoir A and observe the oil level When cold the oil level should be approximately 4 10 cm below top of the filler neck 4 f necessary remove the reservoir cap B and add SAE 20W 50 motor oil 5 Reinstall the reservoir cap Change Hydraulic Oil Filter Change Interval Every 250 Hours Filter Part Number 1719168 NOTE Removing the oil filter from the filter base will drain the oil reservoir Have a suitable container ready to catch any spilled oil The manufacturer recommends this be a dealer only service item 1 Locate the transmission oil filter B Figure 26 at the rear of the battery compartment under the seat 2 Lubricate the new filter base with a few drops of transmission oil Fill the filter half full of oil 3 Clean the area ar
34. bar must be approved by the manufacturer DO NOT exceed the machine weight rating of the roll bar injury or death Avoid serious Evite lesiones graves o la muerte por from rollover volcaduras Do not operate No opere la without the rollbar podadora sin antes installed and instalar la barra antivuelcoy e operational revisar que est funcional 12 11 Operator Safety Safety Interlock System This unit is equipped with safety interlock switches These safety systems are present for your safety do not attempt to bypass safety switches and never tamper with safety devices Check their operation regularly Operational SAFETY Checks Test 1 Engine should NOT crank if PTO switch is engaged OR Parking brake is not engaged OR Motion control handles are not in the NEUTRAL position Test 2 Engine SHOULD crank if PTO switch is NOT engaged AND Parking brake is engaged AND Motion control handles are locked in the NEUTRAL position Test 3 Engine should SHUT OFF if Operator rises off seat with PTO engaged OR Operator rises off seat with parking brake disengaged Operator moves motion control handles out of their neutral positions before disengaging parking brake Test 4 Blade Brake Check Mower blades and mower drive belt should come to a complete stop within seven 7 seconds after electric PTO switch is turne
35. below lists the most common problems their causes and remedies See the information on the following pages for instructions A WARNING To avoid serious injury perform maintenance on the tractor or mower only when the engine is stopped and the parking brake engaged Always remove the ignition key disconnect the spark plug wire and fasten it away from the plug before beginning the maintenance to on how to perform most of these minor adjustments and service repairs yourself If you prefer all of these procedures can be performed for you by your local authorized dealer Troubleshooting the Rider Problem Engine will not turnover or start Engine starts hard or runs poorly Engine knocks Excessive oil consumption Engine exhaust is black 44 Cause 1 2 12 13 1 Mjr Parking brake not engaged PTO electric clutch switch in ON position Out of fuel Engine flooded Fuse blown Battery terminals require cleaning Battery discharged or dead Wiring loose or broken Solenoid or starter motor faulty Safety interlock switch faulty Spark plug s faulty fouled or incorrectly gapped Water in fuel Gas is old or stale Fuel mixture too rich Spark plug faulty fouled or incorrectly gapped Low oil level Using wrong grade oil Engine running too hot Using wrong weight oil Too much oil in crankcase Dirty air filter Engine choke control is in closed p
36. bly practicable Please refer to the engine manufacturer s warranty statement if any that is included in the owner s packet We are not authoized to handle warranty adjustments or repairs on engines Snapper Pro offers NO WARRANTY on mower engines Snapper Pro does not guarantee or represent that any engine manufacturer will comply with the terms of its warranty Items and Conditions Not Covered This warranty does not cover and Snapper Pro makes NO WARRANTY regarding the following Mowers or their parts if a complete and accurate Snapper Pro Product Registration has not been received by Snapper Pro Loss or damage to person or property other than that expressly covered by the terms of this limited warranty Pickup and delivery charges and risk of loss or damage in transit to and from any authorized Snapper Pro dealer Any damage or deterioration due to normal use wear and tear or environmental or natural elements or exposure Cost of regular maintenance service or parts such as but not limited to filters fuel lubricants tune up parts and adjustments Claims arising due to failure to follow Snapper Pro written instructions or improper storage or maintenance Any repairs necessary due to use of parts accessories or supplies including gasoline oil or lubricants incompatible with the mowing equipment or other than as recommended in the operator s manual or other written operational instructions provided by Snapper Pro Use of non Snap
37. cerrada en un rea sin Limpie el combustible que se derrame NO fume mientras opere esta m quina ventilaci n soom OBST CULOS ittempt t antivuelco dafiada NO QUE CUELGAN maq euet intente reparara ni MUY ABAJO PINCH POINT PUNTO PUNZANTE To avoid injury from f Para que no sufra una lesi n loaded spring read por el resorte bajo presi n operator s manual EZB Jes ck manua qel operador before removing spring antes de quitar el resorte wy he AVOID SERIOUS GRAVES LAL INJURY OR DEATH FROM VOLCADURAS ROLL OVER NO salte de la podadora Do NOT jump off if cuando sta se vuelque mower tipe Lea el manual del Read and follow all operador y siga las operating instructions instrucciones de and warnings in the operaci n y las operator s manual advertencias ah K aen incluidas indeed Guardar rollo barra en posici n y uso cintur n position and use seat belt Nunca mudanza rollo Never remove roll bar barra ESTRUCTURA ROLL OVER PROTECTIVE PROTECTORA STRUCTURE VOLCADURAS To maintain operator Para mantener protegido protection and roll bar al operador y la certification certificaci n de la barra Replace a damaged antivuelco roll bar do NOT Reemplace la barra modificarla Cualquier cambio a la barra antivuelco debe ser aprobado por el fabricante NO exceda la clasificaci n de peso de la m quina que especifica la barra antivuelco Any alteration of the roll
38. chniques an explanation of the product s features and controls and maintenance information is included to help you get the most out of your equipment investment Be sure to completely read the Safety Rules and Information found on the following pages Also completely read the Operation section Operating Safety Congratulations on purchasing a superior quality piece of lawn and garden equipment Our products are designed and manufactured to meet or exceed all industry standards for safety Do not operate this machine unless you have been trained Reading and understanding this operators manual is a way to train yourself Power equipment is only as safe as the operator If it is misused or not properly maintained it can be dangerous Remember you are responsible for your safety and that of those around you Use common sense and think through what you are doing If you are not sure that the task you are about to perform can be safely done with the equipment you have chosen ask a professional contact your local authorized dealer Children Tragic accidents can occur with children Do not allow them anywhere near the area of operation Children are often attracted to the unit and mowing activity Never assume that children will remain where you last saw them If there is a risk that children may enter the area where you are mowing have another responsible adult watch them Operator Safety M _ _
39. d off or operator rises off seat If mower drive belt does not stop within seven 7 seconds see your dealer NOTE Once the engine has stopped PTO switch must be turned off parking brake must be engaged and the motion control handles must be locked in the NEUTRAL position after the operator returns to the seat in order to start the engine A WARNING If the unit does not pass a safety test do not operate it See your authorized dealer Under no circumstance should you attempt to defeat the purpose of the safety interlock system 12 Safety Icons The alert symbol A is used to identity safety information about hazards that can result in personal injury A signal word DANGER WARNING or CAUTION is used with the alert symbol to indicate the likelihood and the potential severity of the injury In addition a hazard icon may be used to represent the type of hazard An explanation of hazard levels and icons are as follows A DANGER This indicates a hazard which if not avoided will result in serious injury or death A WARNING This indicates a hazard which if not avoided could result in serial injury or death A CAUTION This indicates a hazard which if not avoided might result in minor or moderate injury hese messages presented without the alert symbol indicate a situation where the unit or property could be damaged North American Safety Icons Amputation Alert Foot in TJ Blade Toxic Thr
40. d the right to release the lock 4 Release the deck lift foot pedal until it comes to rest against the cutting height adjustment pin Foot Pedal Adjustment The deck lift foot pedal can be adjusted to accommodate the operator s height for optimal comfort To adjust pedal position 1 Remove the foot pedal A Figure 7 from the pedal mount tab B 2 Remove the pedal mount hardware C and rotate the tab 180 degrees 3 Reinstall the pedal mount hardware and tighten securely 4 Reinstall the foot pedal on the pedal mount tab in the proper orientation as shown in Figure 7 18 Figure 6 Mowing Height Adjustment A Cutting Height Adjustment Pin B Deck Lift Foot Pedal C Deck Lift Lock lever Figure 7 Foot Pedal Adjustment A Deck Lift Foot Pedal B Pedal Mount Tab C Pedal Mount Hardware D Optional Position www SnapperPro com Raise and Lower the Roll Bar A WARNING AVOID SERIOUS INJURY OR DEATH FROM ROLL OVER Keep roll bar in the raised position and use the seat belt THERE IS NO ROLL OVER PROTECTION WHEN THE ROLL BAR IS DOWN Lower the roll bar only when necessary and NEVER remove it Do NOT use seat belt when the roll bar is down Raise the roll bar as soon as clearance permits Do NOT jump off if mower tips To Lower the Roll Bar 1 Pull the hair pin clips A Figure 8 out of the retainer pins B 2 Push or pull the top of the roll bar C forward a
41. dance with the provisions below to the original purchaser only for the periods described below that the commercial mower shall be free from substantial defects in material or workmanship under normal use and service If you wish to file a claim under this limited warranty you must provide prompt notice of your claim to an authorized Snapper Pro dealer during the warranty period Snapper Pro obligation under this limited warranty is at Snapper Pro option to repair or replace any part or parts of the mower which in the judgment of Snapper Pro are found to be defective and covered by this limited warranty An authorized Snapper Pro dealer will repair or replace the defective part or parts at the dealer s place of business at no charge for the labor or parts This limited warranty applies only to mowers sold in the United States and Canada and is sub ject to the following limitations Covered Parts Warranty Period All Mowers 2 years 24 months from date of retail purchase by the original purchaser for parts amp labor 90 days for rental mowers Except as noted below Belts Tires Brake Pads 90 days from date of retail purchase by the original purchaser And Hoses Battery Blades Attachments 1 year from date of retail purchase by the original purchaser Engine If the engine manufacturer provides any warranty on the mower s engine Snapper Pro will assign that warranty to the original purchaser of the mower if such assignment is reasona
42. djustment Pin amp Deck Lift Lock Lever 1c These control the cutting height of the mower deck Depress the pedal until it locks into the 5 12 7 cm position Place the adjustment pin in the desired cutting height and release the lift lock lever pa Throttle Control The throttle controls engine speed Move the throttle forward to increase engine speed and back to decrease engine speed Always operate at FULL throttle Choke Close the choke for cold starting Open the choke once the engine starts A warm engine may not require choking Pull the knob UP to close the choke Push to knob DOWN to open the choke XI Hour Meter Maintenance Reminder Measures the time of the PTO being engaged The hour meter measures the number of hours the PTO has been engaged The hour meter will flash an initial oil change indicator at 5 hours and a lubrication reminder every 50 hours These reminders display for approximately two hours and will automatically reset themselves Note The hour meter will register the passage of time only when the PTO is engaged The hour meter has a self contained power source so the total hours are always visible Features amp Controls m Fuel Tank Cap To remove the cap turn counterclockwise BR Fuel Level Gauge Displays the fuel level in the tank 15 Operation Operation General Operating Safety Before first time operation Be sure to read all information in the Safety and Operation
43. e Only start engine from the operator s position Use seat belts if provided Be sure of your footing while using pedestrian controlled equipment especially when backing up Walk don t run Reduced footing could cause slipping Slow down and use extra care on hillsides Be sure to travel in the recommended direction on hillsides Turf conditions can affect the machines stability Use caution when operating near drop offs Do not mow in reverse unless absolutely necessary Always look down and behind before and while traveling in reverse Be aware of the mower discharge direction and do not point it at anyone Do not operate the mower without either the entire grass catcher or the deflector in place Slow down and use caution when making turns and when changing directions on slopes Never raise deck with the blades running Never leave a running unit unattended Always disengage the PTO set parking brake stop engine and remove keys before dismounting Keep hands and feet away from the cutting units Turn off the PTO switch to disengage the blades when not mowing Never operate with guards not securely in place Be sure all interlocks are attached adjusted properly and functioning properly Never operate with the discharge deflector raised removed or altered unless using a grass catcher Do not change the engine governor setting or overspeed the engine Stop on level ground lower implem
44. e Briggs amp Stratton P Model 543777 0120 E1 25 HP Kawasaki z Horsepower 32 3600 rpm Model FH721V Displacement 54 62 Cu in 895 cc Horsepower 25 3600 rom Electrical System 12 Volt 20 amp Alternator Battery 340 CCA Orsep idis Oil Capacity 2 4 US at 2 3 L w Filter Displacement 41 2 Cu in 675 cc Electrical System 12 Volt 13 amp Alternator Battery 340 CCA Oil Capacity 2 0 US qt 1 9 L w Filter CHASSIS Fuel Tank Capacity 12 Gallons 45 4 L ix Rear Wheels Tire Size 24 x 12 00 12 20 HP Kawasaki aa Inflation Pressure 15 psi 1 03 bar Model FX730V Front Wheels Tire Size 13 x 6 50 6 Horsepower 26 3600 rpm Inflation Pressure 25 psi 1 72 bar Displacement 44 3 Cu in 26 cc Electrical System 12 Volt 15 amp Alternator Battery 340 CCA TRANSMISSIONS Oil Capacity 2 2 US qt 2 1 L w Filter S N 2014450933 amp Below x Hydro Gear HGM 12E 3131 PG 3H 27 HP Kohler S N 2014450934 amp Above id DUUM Hydro Gear TF0240LS081AAKZ RH PG 3H Horsepower 27 Q 3600 rpm Hydro Gear TF0240LS080AAKZ LH PG 3H Displacement 44 24 Cu in 725 cc Type Pump and Wheel Motor Electrical System 12 Volt 16 amp Alternator Battery 340 CCA Hydraulic Fluid SAE 20W 50 motor oil Oil Capacity 2 1 US qt 2 0 L w Filter Speeds Forward 0 10 MPH 0 16 09 km h 3400 rpm Reverse 0 5 MPH 0 8 05 km h i Continuous Torque 222 ft Ibs 301 N m 27 HP Kawasaki ime 8 l Make Kawasaki Maximum Weight 750 Ibs 340 Kg
45. e MeS 1 Deck is not leveled correctly 1 Level the deck correctly 2 Tires are not properly inflated 2 Check and inflate the tires 3 Blades are damaged 3 Replace the blades 4 Deck shell is damaged 4 Repair or replace the deck 5 Mower spindle is bent or loose 5 Repair or replace the spindle 6 Blades are installed incorrectly 6 Reinstall the blades correctly 1 Deck is not leveled correctly 1 Level the deck correctly 2 Blades are dull or worn 2 Sharpen or replace the blades 3 Blades are damaged 3 Replace the blades 4 Deck is clogged with grass clippings 4 Clean out the deck 5 Deck shell is damaged 5 Repair or replace the deck 6 Mower spindle is bent or loose 6 Repair or replace the spindle 7 Blades are installed incorrectly 7 Reinstall the blades correctly 8 Tires are not properly inflated 8 Check and inflate the tires 1 Blades are not sharp or nicked 1 Sharpen your blades 2 Blades are worn down too far 2 Replace your blades 3 Engine speed is too low 3 Always mow at full throttle 4 Ground speed is too fast 4 Slow down 5 Deck is plugged with grass 5 Clean out the mower 46 www SnapperPro com Specifications Specifications NOTE Specifications are correct at time of printing and are subject to change without notice Actual sustained equipment horsepower will likely be lower due to operating limitations and environmental factors ENGINE 32 HP Briggs amp Stratton Mak
46. e forward and backward seat adjustment models equipped with a suspension seat can be adjusted for lumbar support suspension and back angle Forward and Backward Adjustment Move the forward backward seat adjustment lever A Figure 5 away from the seat position the seat as desired and release the lever to lock the seat into position Lumbar Adjustment Turn the lumbar adjustment knob B until the desired amount of lumbar is achieved Back Angle Adjustment Turn the back angle adjustment knob C until the desired amount of back angle is achieved Suspension Adjustment Turn the suspension adjustment knob D until the display scale has a reading that matches the weight of the operator Operation Figure 4 Seat Adjustment A Seat Adjustment Lever Figure 5 Suspension Seat Adjustment A Forward Backward Seat Adjustment Lever B Lumbar Adjustment Knob C Back Angle Adjustment Knob D Suspension Adjustment Knob 17 Operation Mowing Height Adjustment The cutting height adjustment pin A Figure 6 control the mower cutting height The cutting height is adjustable between 1 3 4 4 4 cm and 5 12 7 cm in 1 4 0 64 cm increments 1 Depress the deck lift foot pedal B until it locks into the 5 12 7 cm position 2 Place the cutting height adjustment pin in the desired cutting height 3 Depress the deck lift foot pedal then push the lock lever C towar
47. ents disengage drives engage parking brake shut off engine before leaving the operator s position for any reason including emptying the grass catchers or unclogging the chute Stop equipment and inspect blades after striking objects or abnormal vibration occurs Make necessary repairs before resuming operations Keep hands and feet away from the cutting units Look behind and down before backing up to be sure of a clear path Never carry passengers and keep pets and bystanders away Do not operate the unit while under the influence of alcohol or drugs Slow down and use caution when making turns and crossing roads and sidewalks Stop blades if not mowing Use care when loading or unloading the machine into a trailer or truck 23 Use care when approaching blind corners shrubs trees or other objects that may obscure vision 24 To reduce fire hazard keep unit free of grass leaves amp excess oil Do not stop or park over dry leaves grass or combustible materials A WARNING It is a violation of California Public Resource Code Section 4442 to use or operate the engine on any forest covered brush covered or grass covered land unless the exhaust system is equipped with a spark arrester as defined in Section 4442 maintained in effective working order Other states or federal jurisdictions may have similar laws Contact an Authorized Service Dealer to obtain a spark arrester designed for the exhaust system i
48. er blade from turning Regular Maintenance EE Figure 30 Sharpening the Mower Blade A Mower Blade Bevel B Mower Blade Cutting Edge Figure 31 Balancing the Mower Blade A Nail Figure 32 Tightening the Mower Blade for Installation A Mower Blade Mounting Bolt B Flat Washer C Mower Blade Air Lift Points Up For Installation D 4 X 4 Wooden Block 31 Regular Maintenance Ground Speed Control Lever Adjustment The control levers can be adjusted in three ways The alignment of the control levers the placement of the levers how close the ends are to one another and the height of the levers can be adjusted To Adjust the Handle Alignment Loosen the mount bolts A Figure 33 and pivot the lever s B to align with each other To Adjust the Handle Placement Loosen the jam nuts and adjust the placement bolt C Figure 34 in or out to properly adjust the lever end spacing To Adjust the Handle Height Remove the mounting hardware and reposition the handle either up or down from its original position You will need to readjust the handle alignment as described above Speed Balancing Adjustment If the rider veers to the right or left when the ground speed control levers are in the maximum forward position the top speed of each of these levers can be balanced by turning the adjustment bolt s A Figure 34 Only adjust the speed of the wheel that is
49. er blades with grinder hand file or electric blade sharpener 2 Sharpen the mower blade by removing an equal amount of material from each end of the mower blade 3 Keep the original bevel A Figure 30 when grinding DO NOT change the mower blade bevel 4 The mower blade should have a maximum 1 64 0 40 mm cutting edge B or less 5 Balance the mower blades before installing Balancing the Mower Blades A CAUTION Avoid injury Keep mower blades balanced An unbalanced mower blade can create excessive vibration and damage the unit or cause mower blade failure 1 Clean the mower blade to remove any dried grass or other debris 2 See Figure 31 Put the mower blade on a nail in a vise and turn the mower blade to the horizontal position 3 Check the balance of the mower blade If either end of the mower blade moves downward sharpen the heavy end until the mower blade is balanced See Sharpening the Mower Blades for proper sharpening instructions 4 Repeat the process until the mower blade remains in the horizontal position Reinstalling the Mower Blades 1 Reinstall each mower blade with the air lifts pointing up towards the mower deck as shown in Figure 32 Secure with the mower blade mounting bolt and flat washer A amp B Figure 32 and torque to 70 ft Ibs 94 Nm 2 If there are no flats on the spindle shaft wedge a wooden block between the mower blade and the mower deck housing to keep the mow
50. er ground speed 24 Where possible make one or two passes around the outside of the area discharging the grass INTO the lawn to keep the cut grass off fences and walks The remainder of the mowing should be done in the opposite direction so that the clippings are dispersed OUT onto the area of lawn previously cut Mowing Methods Proper Broadcast Mowing Broadcasting or side discharging disperses fine clippings evenly over the entire lawn Many golf courses use this method Your mower has a deep dish deck to allow freer circulation of clippings so they are broadcast evenly over the lawn Engine Speed amp Ground Speed for Broadcasting Always operate the engine at full throttle when mowing If you hear the engine slowing down you are mowing too fast using a slower ground speed will improve the cutting efficiency of the blades and prevents many common cutting problems ALWAYS use an appropriate ground speed for the thickness and height of the grass you are cutting 3rd gear or slower for manual gear models If you hear the engine slowing down you are mowing too fast use a slower ground speed How Much Grass to Cut Off When Broadcasting Mow when the grass is 3 5 inches long Do not cut the grass shorter than 2 to 2 1 2 inches Do not cut off more that 1 inch of grass in a single pass www SnapperPro com Proper Mulching Mulching consists of a mower deck which cuts and recuts clippings into tiny particles and
51. er with safety devices Check their proper operation regularly Disengage drives lower implement set parking brake stop engine and remove key or disconnect spark plug wire Wait for all movement to stop before adjusting cleaning or repairing Clean grass and debris from cutting units drives mufflers and engine to prevent fires Clean up oil or fuel spillage Let engine cool before storing and do not store near flame Stop and inspect the equipment if you strike an object Repair if necessary before restarting Park machine on level ground Never allow untrained personnel to service machine Use jack stands to support components when required Carefully release pressure from components with stored energy Disconnect battery or remove spark plug wire before making any repairs Disconnect the negative terminal first and the positive last Reconnect positive first and negative last Use care when checking blades Wrap the blade s or wear gloves and use caution when servicing them Only replace blades Never straighten or weld them Keep hands and feet away from moving parts If possible do not make adjustments with the engine running Charge batteries in an open well ventilated area away from spark and flames Unplug charger before connecting or disconnecting from battery Wear protective clothes and use insulated tools Grass catcher components are subject to wear damage and deterioration which could
52. essories air cleaner exhaust charging cooling carburetor fuel pump etc application limitations ambient operating conditions temperature humidity altitude and engine to engine variability Due to manufacturing and capacity limitations Briggs amp Stratton may substitute an engine of higher rated power for this Series engine 47 n ay jo lBue eui uim PIO ay Jo lBue ay euyeduio enjonajs Jeana Aue 10 qsod 92ue9J e ajod eui jewod e 99J E91119A e YUM epin6 Siul Jo eDpe yo eui u Ily Z aaoge peje5ipur aul poop eui Buoje eBed siu pjoJ L rens sy I ae lia SNOILONULSNI 3dO lS 3H HO 3 19NV JHL OL Q103 SAHLAO 3 19NV AHL 3HVdlWOO ANIT GALLOG 31viudOuddV S9NOTV Q104 Qo 913 ONIGIING LSOd 39N3J 310d 33H11 3ova4uns 1VOILH3A V HLIM 3903 SIHLNSINV _ j AGINS NOILLVOISILNAGNI 3dO 1S o www SnapperPro com 48 Snapper Pro a division of Briggs amp Stratton Power Products Group LLC Owner s Limited Warranty Information Effective 08 01 2007 Thank you for purchasing Snapper Pro commercial mowing equipment Please take a few minutes to read this limited warranty information It con tains all the information you will need to have your Snapper Pro mower repaired in the unlikely event that a breakdown covered by this limited warranty should occur Owner s Responsibilities As a condition to our obligations under this limited w
53. expose moving parts or allow objects to be thrown Frequently check components and replace with manufacturer s recommended parts when necessary Check brake operation frequently Adjust and service as required Use only factory authorized replacement parts when making repairs Always comply with factory specifications on all settings and adjustments Only authorized service locations should be utilized for major service and repair requirements Never attempt to make major repairs on this unit unless you have been properly trained Improper service procedures can result in hazardous operation equipment damage and voiding of manufacturer s warranty Units with hydraulic pumps hoses or motors WARNING Hydraulic fluid escaping under pressure may have sufficient force to penetrate skin and cause serious injury If foreign fluid is injected into the skin it must be surgically removed within a few hours by a doctor familiar with this form of injury or gangrene may result Keep body and hands away from pin holes or nozzles that eject hydraulic fluid under high pressure Use paper or cardboard and not hands to search for leaks Make sure all hydraulic fluid connections are tight and all hydraulic hoses and lines are in good condition before applying pressure to the System If leaks occur have the unit serviced immediately by your authorized dealer 26 WARNING Stored energy device Improper release of springs can result in serio
54. fety Interlock System 12 Features amp Controls 13 Identification Numbers 13 Control FUNCIONS sessirnar annie 14 eri 16 General Sas suma naa an atau a aa 16 Checks Before Starting 16 Checking Tire Pressures 17 Seat Adjusttent nitet ete eene 17 Mowing Height Adjustment 18 Foot Pedal Adjustment 18 Raise and Lower the Roll Bar 19 Starting the Enge 20s reda e 20 Stopping the Rider_ u asa 20 Pushing the Rider by Hand 20 Zero Turn Driving Practice 21 MOWING e a 23 Mowing Reccomendations 23 Mowing Methods serine 24 Attaching a Traller uU L u Lu uu u 1 wass 25 Regular Maintenancoes 26 Maintenance Schedule 26 Checking Adding Fuel 27 uc IU ENS 27 Oil amp Filter Change seeeseeeeeeeeeeee 27 ubica u PIE 28 Check Hydraulic Oil Level 29 Hydraulic Oil Filter Change 29 Servicing
55. g could result in 1 personal injury caused by electrolyte squirting out the battery vents 2 personal injury or property damage due to battery explosion 3 damage to the charging system of the booster vehicle or of the immobilized vehicle Do not attempt to jump start a vehicle having a frozen battery because the battery may rupture or explode If a frozen battery is suspected examine all fill vents on the battery If ice can be seen or if the electrolyte fluid cannot be seen do not attempt to start with jumper cables as long as the battery remains frozen 42 A WARNING For your personal safety use extreme care when jump starting Never expose battery to open flame or electric spark battery action generates hydrogen gas which is flammable and explosive Do not allow battery acid to contact skin eyes fabrics or painted surfaces Batteries contain a sulfuric acid solution which can cause serious personal injury or property damage When removing or installing battery cables disconnect the negative cable FIRST and reconnect it LAST If not done in this order the positive terminal can be shorted to the frame by a tool To avoid engine damage do not disconnect battery while engine is running Be sure terminal connections are tight before starting www SnapperPro com Storage Temporary Storage 30 Days Or Less Remember the fuel tank will still contain some gasoline so never store the u
56. gainst the rubber stops D and remove the retainer pins B 3 Lower the roll bar into the down position see insert Figure 8 To Raise the Roll Bar 1 Pull the hair pin clips A out of the retainer pins B and remove the retainer pins 2 Raise the roll bar C until the rubber stops D contact the upright tubes 3 Push or pull the top of the roll bar forward against the rubber stops and reinstall the retainer pins and hair pin clips to secure the roll bar in the raised position Operation Figure 8 Raise amp Lower the Roll Bar A Hair Pin Clip B Retainer Pin C Roll Bar D Rubber Stop 19 Operation Starting the Engine A WARNING If you do not understand how a specific control functions or have not yet thoroughly read the FEATURES amp CONTROLS section do so now Do NOT attempt to operate the tractor without first becoming familiar with the location and function of ALL controls 1 While sitting in the operator s seat engage the parking brake by pulling the parking brake lever back make sure the PTO switch is disengaged pressed down fully and the motion control handles are locked in the NEUTRAL position 2 NOTE A warm engine may not require choking Set the engine throttle control to FULL throttle position Then fully close the choke by pulling the knob OUT fully 3 Insert the key into the ignition switch and turn it to START 4 After the engine starts
57. ides to or procures for the purchaser outside the terms limitations or exclusions of this limited warranty will not constitute a waiver of the terms limitations or exclusions of this limited warranty nor will such assistance extend or revive the limited warranty Snapper Pro will not reimburse the purchaser for any expenses incurred by the purchaser in repairing correcting or replacing any defective products except for those incurred with Snapper Pro prior written permission and in accordance with this limited warranty Snapper Pro sole and exclusive liability with respect to this limited warranty and the purchaser s exclusive remedy shall be repair or replacement as set forth herein All warranty work must be performed by an authorized Snapper Pro dealer using only Snapper Pro approved replacement parts SNAPPER PRO SHALL HAVE NO LIABILITY FOR ANY OTHER COST LOSS OR DAMAGE INCLUDING BUT NOT LIMITED TO ANY INCIDEN TAL COMPENSATORY INDIRECT PUNITIVE SPECIAL OR CONSEQUENTIAL LOSS OR DAMAGE SNAPPER PRO AGGREGATE LIABILITY WITH RESPECT TO A DEFECTIVE PRODUCT OR PART SHALL BE LIMITED TO AN AMOUNT EQUAL TO THE MONIES PAID BY THE PUR CHASER FOR THAT DEFECTIVE PRODUCT OR PART THIS LIMITED WARRANTY AND SNAPPER PRO OBLIGATIONS HEREUNDER ARE EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING WITHOUT LIMITATION THE IMPLIED WARRAN TY OF MERCHANTABILITY AND THE IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE SNAPPER PRO
58. il fueling is complete Do not use a nozzle lock open device If fuel is spilled on clothing change clothing immediately Never over fill the fuel tank Replace gas cap and tighten securely Use extra care in handling gasoline and other fuels They are flammable and vapors are explosive If fuel is spilled do not attempt to start the engine but move the machine away from the area of spillage and avoid creating any source of ignition until fuel vapors have dissipated Replace all fuel tank caps and fuel container caps securely Maintenance and Storage 1 Always observe safe refueling and fuel handling practices when refueling the unit after transportation or storage Always follow the engine manual instructions for storage preparations before storing the unit for both short and long term periods Always follow the engine manual instructions for proper start up procedures when returning the unit to service Never store the machine or fuel container inside 10 1 12 13 14 15 16 17 18 19 20 2 22 23 24 25 where there is an open flame such as in a water heater Allow unit to cool before storing Shut off fuel while storing or transporting Do not store fuel near flames or drain indoors Keep all hardware especially blade attachment bolts tight and keep all parts in good working condition Replace all worn or damaged decals Never tamp
59. in open position 2 Belt is broken 3 Drive belt slips 4 Brake is not fully released 1 Pulleys or belt greasy or oily 2 Tension too loose 3 Belt stretched or worn 1 Brake is incorrectly adjusted 2 Brake pads worn 1 Steering linkage is loose 2 Improper tire inflation Cause 1 Liftlinkage not properly attached or damaged 1 Engine speed too slow 2 Ground speed too fast 3 Cutting height set too low 4 Discharge chute jamming with cut grass 1 Blade mounting bolts are loose 2 Mower blades arbors or pulleys are bent 3 Mower blades are out of balance 4 Belt installed incorrectly 1 Bentor rough pulleys 2 Using incorrect belt 1 Idler pulley spring broken or not properly attached 2 Mower drive belt broken 1 Electrical wiring damage 2 PTO clutch not adjusted 3 Battery voltage too low N cs ro ma r k ope A Po co k roo Jx e r S Troubleshooting Remedy Turn valve s clockwise to close See Drive Belt Replacement See problem and cause below See authorized service dealer Clean as required Adjust spring tension See Drive Belt Replacement Replace belt See Brake Adjustment Replace with new brake pads Check and tighten any loose connections See Regular Maintenance Section Remedy See authorized service dealer for repair Set to full throttle Decrease Ground Speed
60. inch or shorter decompose more quickly than longer blades Sharp mower blades cut grass cleanly and efficiently preventing frayed edges which harm the grass 3 Mow at time of day when the grass is cool and dry Late afternoon or early evening often provide these ideal mowing conditions 4 Avoid mowing after rain or even heavy dew and never mulch when the grass is wet moist grass does not mulch well and clumps beneath the mower deck Mowing Patterns Always start mowing on a smooth level area The size and type of area to be mowed will determine the best mowing pattern to use Obstructions such as trees fences and buildings and conditions such as slopes and grades must also be considered 1 Cut long straight strips overlapping slightly 2 Where possible change patterns occasionally to eliminate matting graining or a corrugated appearance 3 Fora truly professional cut mow across the lawn in one direction then recut the lawn by mowing perpendicular to the previous cut Note Always operate the engine at full throttle when mowing If you hear the engine slowing down you are mowing too fast using a slower ground speed will improve the cutting efficiency of the blades and prevents many common cutting problems Use an appropriate ground speed for the thickness and height of the grass you are cutting 3rd gear or slower for manual gear models If you hear the engine slowing down you are mowing too fast use a slow
61. n longer clippings The ideal cutting height will vary with climate time of year and quality of your lawn We recommend that you experiment with both the cutting height and ground speed until you achieve the best cut Start with a high cutting height and using progressively lower settings until you find a cutting height that is matched to your mowing conditions and preferences Hai Figure 18 Mulching Action dts Mmi Operation Attaching A Trailer The maximum weight of a towed trailer should be less than 200 Ibs 91kg Secure the trailer with a appropriately sized clevis pin A Figure 19 and clip B Excessive towed loads can cause loss of traction and loss of control on slopes Reduce towed weight when operating on slopes The surface being driven on greatly impacts traction and stability Wet or slippery surfaces can greatly reduce traction and the ability to stop or turn Carefully evaluate the surface conditions before operating the unit and trailer and never operate on slopes greater than 10 See SLOPE OPERATION and TOWED EQUIPMENT in the safety section of this manual for additional safety information 34 1m 20 6m i Figure 19 Trailer Weight Recommendations A Clevis Pin B Clip 25 Regular Maintenance Regular Maintenance Maintenance Schedule The following schedule should be followed for normal care of your rider and mower You will need to keep a rec
62. ng the Mower Belt Idler Spring Length 1 Loosen the jam nut C 2 Turn the adjustment nut D until a measurement of 7 1 4 18 42 cm is achieved 3 Retighten the jam nut 38 Figure 46 Mower Belt Idler Spring Length A Mower Belt Tensioner Spring B Anchor Eyebolt C Jam Nut D Adjustment Nut www SnapperPro com Regular Maintenance Hydraulic Pump Drive Belt Replacement 1 Park the tractor on a smooth level surface such as a concrete floor Disengage the PTO engage the parking brake turn off the engine and remove the ignition key 2 Remove the PTO drive belt see MOWER BELT REPLACEMENT for removal instructions 3 Remove the hardware that secures the clutch anchor pad to the PTO clutch A WARNING STORED ENERGY DEVICE Improper release of the belt tension spring can result in personal injury Use extreme caution when removing this spring Loosen the nut on the spring anchor eyebolt G Figure Figure 47 Hydraulic Pump Drive Belt Replacement 47 to release the majority of the belt tension Use A Pump Drive Belt caution and remove the nut to completely release the B Crankshaft Pulley tension C Pump Pulley 5 Remove the old belt and replace it with the new one x jaler ee Make sure the V side of the belt runs in the grooves of F Spring the crankshaft pulley and pump pulleys B amp C G Spring Anchor Eyebolt Reinstall the spring anchor eyebolt G into the
63. nit indoors or in any other area where fuel vapor could travel to any ignition source Fuel vapor is also toxic if inhaled so never store the unit in any structure used for human or animal habitation Here is a checklist of things to do when storing your unit temporarily or in between uses Keep the unit in an area away from where children may come into contact with it If there s any chance of unauthorized use remove the spark plug s and put in a safe place Be sure the spark plug opening is protected from foreign objects with a suitable cover e f the unit can t be stored on a reasonable level surface chock the wheels Clean all grass and dirt from the mower Long Term Storage Longer Than 30 Days Before you store your unit for the off season read the Maintenance and Storage instructions in the Safety Rules section then perform the following steps 1 Drain crankcase oil while engine is hot and refill with a grade of oil that will be required when unit is used again 2 Prepare the mower deck for storage as follows a Remove mower deck from the unit b Clean underside of mower deck C Coatall bare metal surfaces with paint or light coat of oil to prevent rusting 3 Clean external surfaces and engine 4 Prepare engine for storage See engine owner s manual 5 Clean any dirt or grass from cylinder head cooling fins engine housing and air cleaner element 6 Cover air cleaner and exhaust outlet tightly
64. njury or death Inspect the mower blade every 25 hours or at least once a year If the mower blade hits a solid object stop the engine immediately and inspect the mower blade Never weld or straighten bent mower blades k Remove the mower blade from the unit See Removing the Blade 2 Inspect the mower blade Figures 28 amp 29 Discard the mower blade if it has any of the below conditions A Has more than 5 12 7 mm of the mower blade des E from previous sharpening or wear D jure ed BER Blade Tips igure 28 B Square Corner B The air lifts are excessively eroded B amp C Figure C Air Lift 29 and the notch C is 25 6 35 mm deep or greater p Wear Measurement DISCARD Mower Blade If C Mower blade is bent or broken greater than 5 12 7 mm 3 If the cutting edges are not sharp or have nicks sharpen the blades See Sharpening the Mower Blades ERES Figure 29 inspecting the Mower Blade Air Lifts A New Mower Blade B Mower Blade at Wear Limit A notch begins to form C Mower Blade in Dangerous Condition If notch measures 25 6 35 mm or greater DO NOT USE Replace with new mower blade 30 www SnapperPro com Sharpening the Mower Blade CAUTION Avoid injury Mower blades are sharp Always wear gloves when handling the mower blades Always wear safety eye protection when grinding 1 Sharpen the mow
65. nstalled on this engine 25 OSHA regulations may require the use of hearing protection when exposed to sound levels greater than 85 dBA for an 8 hour time period CAUTION C1 This machine produces sound levels in excess of 85 dBA at the operator s ear and can cause hearing loss V though extended periods of exposure Wear hearing protection when operating this machine SLOPE OPERATION Slopes are a major factor related to loss of control and tip over accidents which can result in severe injury or death All slopes require extra caution If you cannot back up the slope or if you feel uneasy on it do not drive on it A WARNING Do not use this machine on slopes greater than 15 Select slow ground speed before driving onto slope Use extra caution when operating on slopes with rear mounted grass catchers Mow across the face of slopes not up and down use caution when changing directions and DO NOT START OR STOP ON SLOPE Do 1 Mow across slopes not up and down 2 Remove obstacles such as rocks tree limbs etc 3 Watch for holes ruts or bumps Uneven terrain could overturn the unit Tall grass can hide obstacles 4 Use slow speed Choose a slow speed so that you will not have to stop or change speed while on the slope This limit was determined per CEN Standard EN 836 1997 Section 5 2 2 and is based on the EN 836 Stability Test procedure described in Section 4 2 4 2 The 1
66. ord of your operating time Determining operating time is easily accomplished by observing the elapsed time recorded by the hour meter Whichever comes first More often in hot over 85 F 30 C weather or dusty operating conditions 26 Whichever comes first More often in hot over 85 F 30 C weather or dusty operating conditions If equipped Replace if damaged www SnapperPro com Checking Adding Fuel To add fuel 1 Remove the fuel cap 2 Fill the tank to about 1 1 2 3 81 cm of the bottom of the filler neck This will allow for fuel expansion NOTE Do not overfil Refer to your engine manual for specific fuel recommendations 3 Install and hand tighten the fuel cap Fuel Filter The fuel filter is located in the fuel line between fuel tank and carburetor near the fuel pump If filter is dirty or clogged replace as follows 1 Disconnect the negative battery cable Place a container below the filter to catch spilled fuel Using pliers open and slide hose clamps from fuel filter Remove hoses from filter Install new filter in proper flow direction in fuel line Secure with hose clamps Reconnect the negative battery cable when finished Change Oil amp Filter 1 Warm engine by running for a few minutes Refer to the engine operator s manual for oil amp filter replacement instructions 2 Remove the oil drain hose A Figure 20 from the cable clamp C
67. osition prevent accidental starting of the engine Remedy 1 Engage parking brake 2 Place in OFF position 3 If engine is hot allow it to cool then refill the fuel tank 4 Move choke control to closed position 5 Replace fuse 6 Clean the battery terminals 7 Recharge or replace 8 Visually check wiring amp replace broken or frayed wires Tighten loose connections 9 Repair or replace See authorized dealer 10 Replace as needed See authorized service dealer 11 Clean and gap or replace See engine manual 12 Drain fuel amp replace with fresh fuel 13 Drain fuel amp replace with fresh fuel Clean air filter Check choke adjustment Clean and gap or replace See engine manual N i Check add oil as required See engine manual N Clean engine fins blower screen and air cleaner See engine manual Drain excess oil Replace air filter See engine manual Open choke control m op www SnapperPro com Rider Troubleshooting Continued Problem Engine runs but rider will not drive Rider drive belt slips Brake will not hold Rider steers or handles poorly Troubleshooting the Mower Problem Mower will not raise Engine stalls easily with mower engaged Excessive mower vibration Excessive belt wear or breakage Mower drive belt slips or fails to drive Mower does not engage Cause 1 Hydraulic release valve s
68. ound the filter base and remove the filter Do NOT drain the hydraulic system oil 4 Thread the new filter onto the filter base until the gasket makes contact then tighten 3 4 of a turn more 5 Run the unit for several minutes and check the transmission oil level IMPORTANT NOTE Use caution after changing the filter air in the hydraulic system may affect the responsiveness of the control levers Repeat step 5 until the air is out of the system Regular Maintenance Figure 25 Checking Hydraulic Oil Level A Hyaraulic Oil Reservoir B Reservoir Cap Figure 26 Battery Compartment A Hydraulic Oil Reservoir B Hydraulic Oil Filter 29 Regular Maintenance Servicing The Mower Blades Removing the Mower Blade CAUTION Avoid injury Mower blades are sharp Always wear gloves when handling mower blades or working near blades 1 To remove the mower blade use a 1 wrench on the flats of the spindle shaft and remove the mower blade mounting bolt with a 15 16 wrench Figure 27 2 If there are no flats on the spindle shaft wedge a wooden block between the mower blade and the mower deck housing to keep the mower blade from turning Inspecting the Mower Blades DANGER Avoid injury A worn or damaged blade can break and a piece of the mower blade could be thrown into the operator s or bystander s area resulting in serious personal i
69. own Fumes Objects 23 Read the aa pee Manual L L I e Ei Distance Open S Keep Flame eS Children LM Hazard Away Fire Hazard y 7 Hot Surface nil hls abus Amputation ia Wear Rotation KO Protective Parts on Gear Amputation Handin L Pinch Point Blade Rollover Overhead Hazard e 4 Obstacles www SnapperPro com Features and Controls Identification Numbers dq amp STRATTON POW PE GROUP LLC f MILWA N 53201 USA ASSEMBIZWATHE USA PART NO SWSAL NO E S When contacting your authorized dealer for replacement parts service or information you MUST have these numbers Record your part number serial number and engine serial numbers in the space provided on the inside front cover for easy access These numbers can be found in the locations shown in Figure 1 NOTE For location of engine identification numbers refer to the engine owner s manual Operator Safety Figure 1 Identification Numbers A Identification Tag 13 Features and Controls Figure 2 Control Locations Control Functions The information below briefly describes the function of individual controls Starting stopping driving and mowing require the combined use of several controls applied in specific sequences To learn what combination and sequence of controls to use for various tasks see the OPERATION section EH Ground Speed Levers These levers control the ground speed of
70. pe don t do it It s not worth the risk Moving Parts This equipment has many moving parts that can injure you or someone else However if you stay in the operator zone stay seated in the seat and follow the safety rules in this operator s manual the unit is safe to operate The mower deck has spinning mower blades that can amputate hands and feet Do not allow anyone near the unit while it is running Keep safety devices guards shields and switches in place and working To help you the operator use this equipment safely it is equipped with an operator present safety system Do NOT attempt to alter or bypass the system See your dealer immediately if the system does not pass all the safety interlock system tests found in this manual Operator Safety Retaining Walls Drop offs and Water Retaining walls and drop offs around steps and water are a common hazard Give yourself a minimum of two mower widths of clearance around these hazards and hand trim with a walk behind mower or string trimmer Wheels dropping over retaining walls edges ditches embankments or into water can cause rollovers which may result in serious injury death or drowning Roll Bar Use Keep the roll bar in the raised position and fasten the seat belt There is no roll over protection when the roll bar is down Do not jump off if the mower tips it is safer to be secured by the seat belt with the roll
71. per Pro approved parts or accessories Any overtime or other extraordinary repair charges or charges relating to repairs or replacements Rental of like or similar replacement equipment during the period of any warranty repair or replacement work Loss of revenue time or use of the mowing equipment Travel telephone or other communication charges Damage from continued use of defective mowing equipment Freight charges on replacement parts Any mowing equipment or part which in the judgment of Snapper Pro has been altered or tampered with in any way or has been subjected to misuse abuse abnormal usage unauthorized repair neglect or accident damage in transit or has had the serial numbers altered effaced or removed Any equipment part or item not mentioned under Covered Parts above General Conditions Snapper Pro is continually striving to improve its products and therefore reserves the right to make improvements or changes without incurring any obligation to make changes or additions to products sold previously Any oral or written description of Snapper Pro products is for the sole purpose of identifying the products and shall not be construed as an express warranty No warranty claim shall give rise to a right for the purchaser to cancel or rescind any sale No person is authorized to make any warranty or assume for Snapper Pro any liability not strictly in accordance with this limited war ranty Any assistance Snapper Pro prov
72. riodically measure the temperature of the electrolyte If the temperature exceeds 125 F 51 6 C or if violent gassing or spewing of electrolyte occurs the charging rate must be reduced or temporarily halted to prevent battery damage 6 Charge the battery until fully charged until the specific gravity of the electrolyte is 1 250 or higher and the electrolyte temperature is at least 60 F The best method of making certain a battery is fully charged but not over charged is to measure the specific gravity of a cell once per hour The battery is fully charged when the cells are gassing freely at low charging rate and less than 0 003 change in specific gravity occurs over a three hour period Regular Maintenance Jump Starting With Auxiliary Booster Battery Jump starting is not recommended However if it must be done follow these directions Both booster and dis charged batteries should be treated carefully when using jumper cables Follow the steps below EXACTLY being careful not to cause sparks Refer to Figure 49 1 Both batteries must be of the same voltage 2 Position the vehicle with the booster battery adjacent to the vehicle with the discharged battery so that booster cables can be connected easily to the batteries in both vehicles Make certain vehicles do not touch each other 3 Wear safety glasses and shield eyes and face from batteries at all times Be sure vent caps are tight Place damp cloth over vent caps
73. rts CHASSIS Fuel Tank Rear Wheels Capacity 12 Gallons 45 4 L Tire Size 24 x 12 00 12 Inflation Pressure 15 psi 1 03 bar Tire Size 13 x 6 50 6 Inflation Pressure 25 psi 1 72 bar BELTS AND BLADES TRACTOR Pump Drive Belt 61 MOWER DECK Deck Drive Belt 5100893 Mower Blade 5101755 Front Wheels 5101029
74. ructure or hardware 3 Missing damaged or loose mounting hardware 4 Mounting hardware that is of a grade lesser than specified 5 Machine GVW Gross Vehicle Weight including attachments restrained payload fuel and operator in excess of the maximum weight specified on the ROLL BAR label 6 Any modifications that have been made such as unauthorized welds and holes 7 Any permanent deformation or twisting of the ROLL BAR structure 8 That the ROLL BAR label is still in place and is readable 9 That the ROLL BAR on product warning labels are still on the ROLL BAR and are readable If there is any doubt as to the condition of the ROLL BAR remove the machine from service and contact your dealer for assistance 10 Operator Safety A WARNING INSPECT BUCKLE INSPECTION AND MAINTENANCE OF THE ROLL BAR SEAT BELT The seat belt like the ROLL BAR needs to be periodically inspected to verify that the integrity has not been compromised through normal machine use misuse age degradation amp LATCH Failure to properly inspect and maintain the seat belt can cause serious injury or death O modifications or a roll over If the seat belt does 4 INSPECT WEBBING not pass all of the following tests it should be 7 replaced BEFORE EACH USE Conduct the following inspections maintenance of the seat belt and retraction mechanism 1 Check for dirt or debris in the retraction
75. s chemicals known in certain quantities to cause cancer birth defects or other reproductive harm Look for the relevant Emissions Durability Period and Air Index information on the engine emissions label IGNITION SYSTEM GASOLINE MODELS T This spark ignition system complies with Canadian ICES 002 SERVICE AND MAINTENANCE To avoid personal injury or property damage use extreme care in handling gasoline Gasoline is extremely flammable and the vapors are explosive Safe Handling of Gasoline 1 Extinguish all cigarettes cigars pipes and other 10 1 k 12 13 sources of ignition Use only approved gasoline containers Never remove the gas cap or add fuel with the engine running Allow the engine to cool before refueling Never fuel the machine indoors Never store the machine or fuel container where there is an open flame spark or pilot light such as near a water heater or other appliance Never fill containers inside a vehicle or on a truck bed with a plastic bed liner Always place containers on the ground away from your vehicle before filling Remove gas powered equipment from the truck or trailer and refuel it on the ground If this is not possible then refuel such equipment on a trailer with a portable container rather than from a gasoline dispenser nozzle Keep nozzle in contact with the rim of the fuel tank or container opening at all times unt
76. sections before attempting to operate this tractor and mower Become familiar with all of the controls and how to stop the unit Drive in an open area without mowing to become accustomed to the unit A WARNING Never allow passengers to ride on the unit Before leaving the operator s position for any reason engage the parking brake disengage the PTO stop the engine and remove the key To reduce fire hazard keep the engine tractor and mower free of grass leaves and excess grease Do not stop or park tractor over dry leaves grass or combustible materials Gasoline is highly flammable and must be handled with care Never fill the tank when the engine is still hot from recent operation Do not allow open flame smoking or matches in the area Avoid over filling and wipe up any spills WARNING Do not load this zero turn rider on a trailer or truck using two separate ramps Only use a single ramp that is at least one foot wider than the width of the rear wheels of this rider This rider has a zero turning radius and the rear wheels could fall off the ramps or the rider could tip over injuring the operator or bystanders 16 A WARNING Never operate on slopes greater than 15 Select slow ground speed before driving onto a slope Use extra caution when operating on slopes with a rear mounted grass catcher Mow across the face of slopes not up and down use caution when changing directions and DO N
77. ssionals for finish cutting of established lawns and is not intended for any other purpose It is important that you read and understand these instructions thoroughly before attempting to start or operate this equipment Save these instructions for future reference PRODUCT REFERENCE DATA Unit Model Number Unit SERIAL Number ower Deck Model Number Mower Deck SERIAL Number m ENGINE REFERENCE DATA Engine Make Engine Model Engine Type Spec Engine Code Serial Number See Features and Controls for the location of Identification Numbers f The engine exhaust from this product contains Briggs amp Stratton Yard Power Products Group chemicals known to the State of California to Copyright 2010 Briggs amp Stratton Corporation cause cancer birth defects or other reproductive Milwaukee WI USA All rights reserved harm The Snapper Pro logo is a trademark of Briggs amp Stratton Corporation Milwaukee WI USA Contact Information Briggs amp Stratton Yard Power Products Group 5375 N Main St Munnsville NY 13409 4003 800 933 6175 www SnapperPro com WARNING Battery posts terminals and related accessories contain lead and lead compounds chemicals known to the State of california to cause cancer and reproductive harm Wash hands after handling Table of Contents Operator Safety usu eese aaussssssssasssssssssh 2 Safety Rules and Information 2 Sf EPI c 11 Sa
78. st slightly forward Practice Turning In Place To turn in place Zero Turn gradually move one ground speed control lever forward from neutral and one lever back from neutral simultaneously Repeat several times NOTE Changing the amount each lever is pulled forward or back changes the pivot point you turn on Executing Turns Turning In Place Figure 13 Turning Around a Corner Figure 14 Turning in Place Executing an End Of Row Zero Turn Your Zero Turn Rider s unique ability to turn in place allows you to turn around at the end of a cutting row rather than having to stop and Y turn before starting a new row For example to execute a left end of row zero turn 1 Slow down at the end of the row 2 Move the RIGHT ground speed control lever forward slightly while moving the LEFT ground speed control lever back to center and then slightly back from center 3 Begin mowing forward again This technique turns the rider LEFT and slightly overlaps the row just cut eliminating the need to back up and re cut missed grass As you become more familiar and experienced with operating the Zero Turn rider you will learn more maneuvers that will make your mowing time easier and more enjoyable Remember the more you practice the better your control of the Zero Turn will be Figure 15 Execu
79. st the clevis Remove the blocks from the under the mower deck Remove the cutting height adjustment pin from in front of the deck lift pedal arm Lift mower deck and reinstall adjustment pin in desired mowing height Regular Maintenance Figure 40 2 x 4 Locations 35 Regular Maintenance Deck Leveling Adjustment NOTE Before adjusting the deck level the deck lift rod timing must be checked and or adjusted Coarse Adjustment Procedure When adjusting the deck level the coarse adjustment procedure should be used to make the majority of the adjustment and the fine adjustment procedure should be used to complete the adjustment 1 Park machine on a flat level surface Disengage the PTO stop the engine and engage the parking brake Rear tires must be inflated to 15 psi 1 03 bar front tires to 25 psi 1 72 bar 2 Lock the deck lift pedal in the 5 12 7cm position Place the deck height adjustment pin in the 4 position and lower deck the lift pedal until the arm contacts the pin 3 Place 2 x 4 blocks under each corner of the mower deck with the 3 1 2 sides being vertical See Figure 40 4 Loosen the nuts and allow the front of the deck to rest on the 2 x 4 s Slide the chains down in the slots until the chains are tight and tighten the nuts See Figure 41 5 Loosen the nuts and allow the rear of the deck to rest on the 2 x 4 s Slide the chains down in the slots
80. the rider The left lever controls the left rear drive wheel and the right lever controls the right rear drive wheel Moving a lever forward increases the FORWARD speed of the associated wheel and pulling back on a lever increases the REVERSE speed Note The further a lever is moved away from the neutral position the faster the drive wheel will turn See the Operation section for proper steering instructions 14 Seat Adjustment Lever The seat can be adjusted forward and back Move the lever towards the left position the seat as desired and release the lever to lock the seat in position Ignition Switch The ignition switch starts and stops the engine it has three positions jor Stops the engine and shuts off the electrical system Ws Allows the engine to run and powers the electrical system start Cranks the engine for starting NOTE Never leave the ignition switch in the RUN position with the engine stopped this drains the battery www SnapperPro com Parking Brake DISENGAGE ENGAGE Pull the parking brake lever back to engage the parking brake Move the lever fully forward to disengage the parking brake NOTE To start the unit the parking brake must be engaged Releases the parking brake Locks the parking brake PTO Power Take Off Switch The PTO switch engages and disengages the mower Pull UP on the switch to engage and push DOWN to disengage tes Deck Lift Pedal Cutting Height A
81. ting an End Of Row Turn 22 www SnapperPro com Mowing 1 Engage the parking brake Make sure the PTO switch is disengaged the motion control levers are locked in the NEUTRAL position and the operator is on the seat Start the engine see Starting The Engine 3 Set the mower cutting height see Mowing Height Adjustment Set the throttle to FULL Engage the PTO by pulling up on the PTO switch Begin mowing When finished shut off the PTO by pushing the PTO switch down completely 8 Stop the engine see Stopping The Rider and Engine n2 NOOO Mowing Recommendations Several factors can affect how well your machine cuts grass Following proper mowing recommendations can improve the performance and life of your machine Height of Grass Often cutting height is a matter of personal preference Typically you should mow the grass when it is is between three and five inches high The proper cutting height range for a specific lawn will depend upon several factors including the type of grass the amount of rainfall the prevailing temperature and the lawn s overall condition Cutting the grass too short causes weak thin grass plants which are easily damaged by dry periods and pests Cutting too short is often more damaging than allowing the grass to be slightly higher Letting grass grow a bit longer especially when it is hot and dry reduces heat build up preserves needed moisture and
82. traveling faster To Reduce the Speed of the Faster Wheel 1 Loosen the securing nut 2 Turn the top speed adjustment bolt COUNTER CLOCKWISE to reduce the speed 3 Retighten the securing nut when adjustment is complete A WARNING DO NOT adjust the tractor for a faster overall speed forward or reverse than it was designed for 32 Figure 33 Control Lever Adjustment A Placement Hardware B Ground Speed Control Lever 4 e i Figure 34 Top Speed Adjustment A Top Speed Adjustment Bolt B Control Lever Base C Alignment Hardware www SnapperPro com Neutral Adjustment If the tractor creeps while the ground speed control levers are locked in NEUTRAL then it may be necessary to adjust the linkage rod NOTE Perform this adjustment on a hard level surface such as a concrete floor 1 Disengage the PTO engage the parking brake and turn off the engine 2 There are three nuts B Figure 35 on the linkage rod A The first two are to be used together to turn the rod and the third towards the front of the machine is used to lock the rod in place Loosen the jam nut that locks against the ball joint and turn the linkage rod to adjust If the machine creeps forward turn the rod CLOCKWISE while standing at the rear of the machine facing forward if the machine creeps backward turn the rod COUNTER CLOCKWIS
83. uries These operators should evaluate their ability to operate the riding mower safely enough to protect themselves and others from serious injury kana kala Evaluate the terrain to determine what accessories and attachments are needed to properly and safely perform the job Use only accessories and attachments approved by the manufacturer Wear appropriate clothing including safety shoes safety glasses and ear protection Long hair loose clothing or jewelry may get tangled in moving parts Inspect the area where the equipment is to be used and remove all objects such as rocks toys and wire which can be thrown by the machine Use extra care when handling gasoline and other fuels They are flammable and vapors are explosive a Use only an approved container b Never remove fuel cap or add fuel with the engine running Allow engine to cool before refueling Do not smoke C Never refuel or drain the machine indoors Check that operators presence controls safety Switches and shields are attached and functioning properly Do not operate unless they are functioning properly OPERATION iL Never run an engine in an enclosed area 11 12 13 14 15 16 17 18 19 20 2 22 Mow only in the daylight or with good artificial light keeping away from holes and hidden hazards Be sure all drives are in neutral and parking brake is engaged before starting engin
84. us personal injury Springs should be removed by an authorized technician 27 Models equipped with an engine radiator WARNING Stored energy device To prevent serious bodily injury from hot coolant or steam blow out never attempt to remove the radiator cap while the engine is running Stop the engine and wait until it is cool Even then use extreme care when removing the cap ROLL BAR INSTRUCTIONS For models equipped with factory installed Roll Over Protection System ROPS A WARNING In order to avoid serious injury or death from roll over it is important to follow the warnings listed below OPERATIONAL WARNINGS Always use the seat belt when the roll bar is in the raised position Never use the seat belt when the roll bar is in the down position Remember there is no roll over protection when the roll bar is in the down position so it is very important to always keep the roll bar in the raised position whenever possible Lower the roll bar to the down position only when it is absolutely necessary Check for overhead clearances before driving under any objects Do not allow roll bar to contact low overhanging obstacles such as tree branches and guide wires Never remove the roll bar from the vehicle Do not exceed the machine weight rating of the roll bar Read and follow all of the instructions shown below regarding the inspection and maintenance of the roll bar structure and the seat belt INSPECTION OF THE
85. with plastic or other waterproof material to keep out moisture dirt and insects 7 Completely grease and oil unit as outlined in the Normal Care section 8 Clean up unit and apply paint or rust preventative to any areas where paint is chipped or damaged 9 Be sure the battery is filled to the proper level with water and is fully charged Battery life will be increased if it is removed put in a cool dry place and fully charged about once a month If battery is left in unit disconnect the negative cable Regular Maintenance A WARNING Never store the unit with gasoline in engine or fuel tank in a heated shelter or in enclosed poorly ventilated enclosures Gasoline fumes may reach an open flame spark or pilot light such as a furnace water heater clothes dryer etc and cause an explosion Handle gasoline carefully It is highly flammable and careless use could result in serious fire damage to your person or property Drain fuel into an approved container outdoors away from open flame or sparks 10 Drain fuel system completely or add a gasoline stabilizer to the fuel system If you have chosen to use a fuel stabilizer and have not drained the fuel system follow all safety instructions and storage precautions in this manual to prevent the possibility of fire from the ignition of gasoline fumes Remember gasoline fumes can travel to distant sources of ignition and ignite causing risk of explosion and fire NOTE

Fluke PM6685 Outdoor Timer User Manual

Contents

Download Pdf Manuals

Related Search

Related Contents