Fantom Vacuum FM744H Vacuum Cleaner User Manual
Contents
1. one of the attachments setthe RUG FLOOR TOOLS selector tothe FLOOR position Caution Do notchange the setting of the RUG FLOOR TOOLS selector while the vacuum cleaner is turned off EDGE CLEANING This vacuum cleaner is equipped with an edge cleaning function for cleaning carpet edges near baseboards and stationary furniture USING THE ATTACHMENTS Caution When usingone of the attachments during cleaning set the vacuum cleaner to the upright position 1 Remove the attachments from the vacuum cleaner Release 2 Press the release button C to Button C disconnect the handle from the vacuum cleaner Caution When removing the attachments pull them inthe directions shown in the illustration Pulling them in the wrong direction or pulling them forcefully may cause damage to the attachment clamp oS Attach the attachments onthe handle or Attachment Clamp the suction hose B e Attach the attachments as shown below Wand Upholstery Dusting ool Brush Crevice Tool Suction Hose A N mpo sh Caution Before using the suction hose B please make sure the handle is Suction Hose B reattached onthe body Handle p lt e Hook the hose holder onto the holder mount Caution Before using the attachments please make sure the hose is hooked on the holder mount Hose Holder Upholstery tool amp Dusting brush E To detach the dusting brush from the uphols2. FANTO M INSTRUCTION MANUAL VACUUM CLEANER FM744H Contents IMPORTANT SAFETYINSTRUCTIONS __ 1 NAME OF EACH PART 3 PREPARATION BEFORE USE 4 USING THE VACUUM CLEANER 6 USING THEATTACHMENTS 8 AIR DRIVEN TURBO BRUSH een 10 EMPTYING THE DUST COMPARTMENT 11 CLEANING THE FILTERS o 12 CLEARING BLOCKAGES IN THE SUCTION HOSE AND CLEANING THE 13 AGITATORASSEMBLY REPLACEMENT INSTRUCTIONS oooi 14 TROUBLESHOOTING ooo 18 REPLACEMENT PARTS o 18 LIMITED WARRANTY ooon 19 HOUSEHOLD AND COMMERCIAL USE IMPORTANT SAFETY INSTRUCTIONS W hen using an electrical appliance basic precautions should always be followed including the following READ ALL INSTRUCTIONS BEFORE USING THIS VACUUM CLEANER WARN N G To reduce the risk of fire electric shock or injury 1 10 11 12 T3 14 13 Do not leave the vacuum cleaner when plugged in Unplug itfrom the outlet when notin use and before servicing Do not use outdoors oron wetsurfaces Do not allow vacuum cleaner to be used asa toy Close attention is necessary when used by or near children or infirmed persons Use only as described inthis manual Use only the manufacturer s recommended attachments Do not use with a damaged cord or plug If the vacuum cleaner is not working as itshould orif ithas been dropped damaged left outdoors or dropped into water return to FANTOM at 94 Main Mill S
3. on the switch ON OFF Switch The handle ofthis vacuum cleanercan be setto one of three positions Upright Normal Parallel Place your foot on handle releaselever as shown and pull backon the handle until it releases from its upright position Normal position Upright position This position is used for normal cleaning The handle is normally locked inthis position for storage or when using the attachments Push the handle forward until it locks JD CK Sa Handle Release Lever Parallel position This position is used for cleaning under furniture E en ES y OMS USING THE VACUUM CLEANER HEIGHT ADJUSTMENT LEVER Caution Before using the height adj ustment lever please make Height AdjustmentLever SS sure the nozzle head is tilted backward from the floor The nozzle head can be adjusted to four different height settings Nozzle Head Set the height adjustment to the appropriate carpet length V 4 Use the 3 Zam height setting ARBEr ae a canter TURN OFF BRUSH ROLL HER WHEN USING TOOLS RUG FLOOR TOOLS SELECTOR The RUG FLOOR TOOLS selector should only be adjusted while the vacuum cleaner is turned on and inthe upright position When cleaning a rugor carpet first turn the ON OFF switch to the ON T T position and then set the RUG Why Va FLOOR TOOLS selector tothe RUG position Rug Floor Tools When cleaning a bare floor or when using SELECTOR
4. position disconnect the power cord from the wall outlet and contact FANTOM Customer Service at 1 800 275 9251 The motor does notoperate The power cord plugis not e Insert the power cord plu when the ON OFF switch is securely inserted into the securely te the wall eine set tothe ON position wall outlet outlet refer to page 5 Suction force is weak e The dust compartment is full e Empty the dust compartment refer to page 11 e The suction hose is blocked e Remove the blockage refer to page 13 e The nozzle head is blocked Remove the blockage refer to page 13 e The filters are dirty e Clean the filters refer to page 12 refer to page 17 e The nozzleair inlet pipe is e Remove the blockage blocked refer to page 13 e The bypass vavie isopened Remove the blockage refer to page 13 The agitator does not The flat belt is worn or e Replace the flat belt operate broken refer to page 15 TO ORDER REPLACEMENT FILTERS CALL 1 800 275 9251 9BF D P111 00728 0408 E 18 FANTO M FIVE 5 YEAR LIMITED WARRANTY FANTOM warrants this product to be free from defects in material and workmanship for a period of five 5 years from the date ofthe original purchase when utilized for normal commercial or household use subject to the following conditions exclusions and exceptions If your appliance fails to operate properly while in use under normal household conditions with
5. insert the projection on the Push the dust compartment into dust compartment into the groove onthe main body the main body as shown to reattach Projection Groove 11 CLEANING THE FILTERS 1 Remove the dust compartment refer to page 11 Set the dust compartmentto the parallel position Open the trapdoor then push the PAE E release button E and pull outthe main filter The main filter and prefilter willbe removed atthe same time Caution Do not push the release button E at the upright position As this may drop or damage the main filter and prefilter Clean the main filter and prefilter with a soft bristled brush not included and rinse with cold water Allow both items to dry completely for 24 hours GA Caution e Do notuse ahard bristled brush to clean filters This may result in damage to the filters e Do notattempt to dry witha hairdryer or by placing ina clothes dryer Hot air may cause the filters to warp lt tr Cleaning Utensil To maintain optimum suction power the dustfilter fins should be kept clean of dirt Clean the filter fins free of dirt with the forked end of cleaning utensil as shown Cleaning Utensil Reattaching the filters 1 Insert the main filter into the Hold onto the main filter and insert into prefilter as shown the dustcompartment e Align the ribs ofthe main filter to match the shape of the opening inthe dust Prefilter compartment and press firmly
6. WINDING THE POWER CORD 1 Wind the power cord around the cord storage hooks 1 Secure the power cord plug on the power cord CoM r Cord Storage Hooks E TUL lt M WOT T Return the hook to the upright position before attempting to rewind the power cord Rotate the upper cord storage hook downward Upper Cord Storage Hook To protect your vacuum cleaner motor from overheating a thermal safety device has been built in If your vacuum cleaner hose orair intake clogs up with dustor dirt or if your dust bag becomes full and you continue to run the machine the vacuum will shut off automatically to prevent the motor from overheating If this happens turn off slide switch and disconnect your vacuum from power outlet remove the material clogging the machine and let your vacuum cool down for approximately 45 minutes You can then restart your vacuum cleanerand useit again INSERTING THE POWER CORD PLUG WARNING This appliance is equipped with a grounded type 3 wire cord 3 prong plug This plug will only fit into an electrical outlet made for a 3 prong plug This is a safety feature If the plug should fail to Grounded Outlet N T A fit the outlet contact an electrician to replace the outlet Do not attempt to defeat the safety purpose of the grounding pin part of the 3 prong plug Grounding Pin USING THE VACUUM CLEANER ON OFF SWITCH Start or stop vacuum cleaner by pushing
7. e humidity 22 When carrying the vacuum cleaner hold it by the carrying handle 23 Before servicing the vacuum cleaner allow all internal metal parts to cool first 24 Always place foot on handle release when adjusting the handle position of the vacuum cleaner 25 Ifthe supply cord of this appliance is damaged it must only be replaced by FANTOM because special purpose tools are required 26 Connect to a properly grounded outlet only See Grounding Instructions SAVE THESE INSTRUCTIONS This vacuum is intended for household or commercial use Note to user concerning attachment plug Grounding Instructions This appliance must be grounded If it should malfunction or breakdown grounding provides a path of least resistance for electric current to reduce the risk of electric shock This appliance is equipped with a cord having an equipment grounding confuctor and grounding plug The plug must be isnerted into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances WARNING Improper connection of the equipment grounding conductor can result in a risk of electric shock Check with a qualified electrician or service person if you are in doubt as to whether the outlet is properly grounded Do not modify the plug provided with the applince if it will not fit the outlet have a proper outlet installed by a qualified electrician This appliance is for use on a nominal 120 volt circ
8. flat belt from the motor shaft and the agitator pulley Motor Shaft Flat Belt 1L Motor Shaft Flat Belt Flat Belt Pulley 4 Place the agitator assembly into the grooves in the nozzle head making sure thatthe new flat belt slides securely into the guide Caution Install the flat beltso thatit has no twists init and so thatall components turn smoothly 5 Reattach the bottom plate refer to page 16 15 REPLACEMENT INSTRUCTIONS REMOVING THE BOTTOM PLATE Set the vacuum cleaner to the parallel position and turn it over Using aPhilips screwdriver loosen the screw on the bottom plate 3 Lift the bottom plate off Insert the projection onthe bottom plate Re tighten the screw using a Philips into the groove onthe nozzle housing screwdriver and setthe bottom plate inplace REPLACEMENT INSTRUCTIONS REPLACING THE FILTER Under normal usage the HEPAFilter will require replacement once every three 3 months however vacuuming large amounts of extremely fine dust powder or similar material over along period of time may decrease airflow performance through the filter If this occurs it may become necessary to replace the HEPAFilter more often Only use genuine FANTOM replacement filters Filter Cover 1 Press inthe locking tabs at points Q and pull the filter cover away from the vacuum cleaner 2 Remove the HEPAfilter Caution e Do notattempt to wash the HEPATfilter Always rep
9. in the warranty period return the complete appliance and accessories freight prepaid to In US FANTOM 94 Main Mill Street Door 16 Plattsburgh N Y 12901 If the appliance is found by FANTOM to be defective in material or workmanship FANTOM will repair or replace it free of charge Proof of purchase date and 19 95 to cover the cost of return shipping and handling must be included Non durable parts including without limitation dust cup filters filters belts brushes and electrical parts which normally require replacement are specifically excluded from warranty The liability of FANTOM is limited solely to the cost of the repair or replacement of the unit at our option This warranty does not cover normal wear of parts and does not apply to any unit that has been tampered with or used for commercial purposes This limited warranty does not cover damage caused by misuse abuse negligent handling or damage due to faulty packaging or mishandling in transit This warranty does not cover damage or defects caused by or resulting from damages from shipping or repairs service or alterations to the product or any of its parts which have been performed by a repair person not authorized by FANTOM This warranty is extended to the original purchaser of the unit and excludes all other legal and or conventional warranties The responsibility of FANTOM if any is limited to the specific obligations expressly assumed by it under the terms of the limi
10. ition automatically after the blockage is removed Cleaning the agitator assembly When threads get caughtin the agitator assembly clean the assembly Remove the bottom plate refter to page 16 Remove threads caught in the assembly by cutting them with scissors Scissors Threads REPLACEMENT INSTRUCTIONS Caution Be sure to turn the ON OFF switch to the OFF position and disconnect the power cord fromthe walloutlet before replacing any of the parts below REPLACING THE HEADLIGHT LAMP 1 Set the vacuum cleaner to the parallel position cima aw UA OCC 2 Loosen the screws to remove the lens Saren es Lens 3 When removing the headlight lamp be careful not to pull on the headlight lamp wiring 4 Remove the lamp by pushing it gently in the direction of the arrow and then turning it counterclockwise 5 Push anew lamp gently into the socket and turn it clockwise to tighten it Usea standard bayonet base appliance lamp rated at 120V and 15W LAMP MAX 15W Caution Be careful not to clamp the headlight lamp wiring 6 Reattach the lensand fasten the screws 14 REPLACEMENT INSTRUCTIONS Caution Be sure to turn the ON OFF switch to the OFF position and disconnect the power cord from the wall outlet before replacing any of the parts below REPLACING THE FLAT BELT 1 Remove the bottom plate refer to page 16 2 Lift out the agitator assembly and then remove the
11. lace the old filter with a new one Insert a new HEPAfilter with the seal to the inside of the vacuum cleaner Reattach the filter cover Caution e Be sure that seal on the HEPAfilter is inserted towards the inside of the vacuum cleaner e The filter cover should be correctly oriented when it is reattached Do not reattach it upside down CLEANING THE SUB FILTER Clean the sub filter when it becomes dirty 1 Remove the dust compartment refer to page 11 Remove the air inlet cover 2 Remove the sub filter from the vacuum cleaner 3 Gently clean the sub filter with water Make sure that itis completely dry and then re install it into the vacuum cleaner Replace the air inlet cover andthe dust compartment Caution Do not wash the sub filterin awashing machine and donot use any other equipment such asa hairdryer to dry it Always allow 24 hours for drying Do not operate the vacuum without the sub filter Be sure the sub filteris dry and properly installed Failure todo socould resultin electrical shock personal injury or motor failure Note We recommend replacing the sub filter every three 3 to six 6 months depending on usage TROUBLESHOOTING If thereis a problem withthe vacuum cleaner carry outthe following checks to find the cause If the problem still persists after the checks have been made do notuse the vacuum cleaner to preventthe possibility of an accident occurring Turn the ON OFF switch tothe OFF
12. oves freely by rotating it with your finger If the turbine does not rotate call FANTOM Customer Service for help 6 Once clean close the top cover of the Turbo Brush and slide the locking latch toward the rear of the brush to lock IMPORTANT TURBO BRUSH INSTRUCTIONS The efficiency of your Air Driven Turbo Brush depends on the bristle brush rotating at high speed Strong air suction is needed to accomplish this In order to ensure that maximum air suction is maintained please read the following instructions 1 Empty the Dust Container frequently during use Follow instructions for dust container 2 Ensure that the rotating brush is kept clear of hair and string 3 Inspect the turbine regularly to ensure that the air passage is free of dirt and debris EMPTYING THE DUST COMPARTMENT Caution Be sure to turn the ON OFF switch to the OFF position and disconnectthe power cord from the wall outlet before cleaning Empty the dust compartment when Press the release button Ameanwhile contents reach the MAX mark press therelease buttonB toremove the dust compartment D Release Button A y Release Button B Press the release lever to open the Turn the duster handle several times in the trapdoor direction shown to empty the dust compartment Release Lever Trapdoor Reattaching the Dust Compartment Close the trapdoor and
13. s push hose in till it clicks AIR DRIVEN TURBO BRUSH Using the Unit With Air Driven Turbo Brush The efficiency of your Air Driven turbo brush depends on the bristle brush rotating at high speed Strong air suction is needed to accomplish this In order to ensure that maximum air suction is maintained please read the following instructions 1 Always empty the dust cup container frequently during use Follow instructions on dust container 2 Ensur that the rotating brush is kept free of hair and string which may accumulate and decrease brush performance 3 Keep Air Driven Turbo Brush turbine free of dirt and foreign matter see illustration below for cleaning instructions Using The Unit With Air Driven Turbo Brush Your Air Driven turbo Brush may be used with either the extension tubes or the flexible hose Cleaning Air Driven Turbo Brush Locking Latch Turbine From time to time the turbine of your Turbo Brush will require cleaning To do this 1 Remove the turbo brush from the hose or extension tube 2 Slide locking latch forward then tilt the top housing of the brush upwards The top housing is hinged and will tilt up approximately 45 only 3 There may be some dust lint hair etc on the turbine wheel Remove as much of this as possible 4 You may also use the unit s hose with crevice tool attached and use the vacuum to remove any additional debris from the turbine 5 Ensure that the turbine wheel m
14. ted warranty In no event is FANTOM liable for incidental or consequential damages of any nature whatsoever Some states do not permit the exclusion or limitation of incidental or consequential damages so the above may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state Important Carefully pack item to avoid damage in shipping Be sure to include proof of purchase date and to attach tag to item before packing with your name complete address and phone number with a note giving purchase information model number and what you believe is the problem with item We recommend you insure the package as damage in shipping is not covered by your warranty Mark the outside of your package ATTENTION CUSTOMER SERVICE OWNERSHIP REGISTRATION CARD Please fill out and mail the product registration card within ten 10 days of purchase The registration will enable us to contact you in the unlikely event of a product safety notification By returning this card you acknowledge to have read and understood the instructions for use and warnings set forth in the accompanying instructions RETURN TO FANTOM 94 Main Mill Street Door 16 Plattsburgh N Y 12901 Model FM744H Appliance model Date purchased Name of store Owner s name Address City State Zip Code Printed in China
15. tery tool Press the r roove tabs on the brush downward to remove it e To reattach the dusting brush to the upholstery tool Insert the front of the upholstery tool under the hook on the front of the dusting brush Press down on the back of the upholstery tool to snap it into place under the dusting brush tabs When you have finished using the attachments replace them in their original positions as shown on page 4 USING THE ATTACHMENTS Caution When using one of the attachments during cleaning setthe vacuum cleaner to the upright position Pet Hair Attachment Assemble the attachments onthe suction hose Aor B Pet Hair e Assemble the accessories as shown below Attachment Wand Handle Adapter gt gt 5z S gt Suction Hose A Twist pet hair attachment cuff until it locks 2 Caution Before using the suction hose B please make sure the handle is Suction Hose B reattached onthe body Hf vi lt 1 Press the release button C to disconnect the handle from the vacuum cleaner To attach the Pet Hair Attachment twistthe cuffon end of attachment onto the adapter until itlocks then slide adapter into wand or into Suction Hose B To remove the Pet Hair Attachment twist the cuffon end of attachmentand pull to 3 release WARNING Do NOT use Pet Hair Attachment on animals this attachement is intended for household cleaning only Hose Attachment Handle Line up notche
16. to insert Dust Compartment Main Filter 3 Close the trapdoor NOTE We recommend replacing the main filter every three 3 to six 6 months depending on the amount of use 12 CLEARING BLOCKAGES AND CLEANING THE AGITATOR ASSEMBLY Caution Be sure to turn the ON OFF switch tothe OFF position and disconnect the powercord fromthe wall outlet before clearing any blockages in the suction hose and cleaning the agitator assembly Cleaning blockages Cleaning blockages in the suction hose A B 1 Set the vacuum cleaner to the upright position Remove the hose cuff from the suction inlet and then remove any blockages from the hose Reattach the hose cuff to the suction inlet and then operate the vacuum cleaner to check that the blockage has been properly cleared If the hose is still blocked the suction force will be weak Cleaning blockages inthe nozzle head 1 Remove the bottom plate refer to page 16 Nozze Head 2 Remove any blockages from the nozzle head Nozzle Pipe Reattach the bottom plate to the nozzle head and then operate the vacuum cleaner to check that the blockage has been properly cleared Ifthe nozzle head is still blocked the suction force will be weak Caution When the suction hose A B or Nozzle head is Bypass Valve blocked the bypass valve will be opened Inside automatically to protect the motor resulting in the suction force being reduced The bypass valve will be at its original pos
17. treet Door 16 Plattsburgh NY 12901 Do not pull or carry by the cord use the cord as a handle close a door on the cord or pull the cord around sharp edges or corners Do notrun the vacuum cleaner overthe cord Keep the cord away from heated surfaces Do not unplug by pulling on the cord To unplug grasp the plug notthe cord Do not handle the plug or the vacuum cleaner with wet hands Do not putany objects into the openings Do not use with any opening blocked keep free of dust lint hair and anything that may reduce air flow Keep hair loose clothing fingers and all the parts of your body away from openings and moving parts Do not pick up anything thatis burning or smoking such as cigarettes matches orhot ashes Do not use without dust compartment and filters in place Turn offall controls before unplugging Use extra care when cleaning on stairs Do not useto pickup flammable or combustible liquids such as gasoline or use in areas where they may be present Rev 08 04C 16 Do not touch the agitator while it is spinning 17 Do not place any heavy items on top of the vacuum cleaner 18 Do not step on the hose or pull it too strongly 19 Do not pick up items such as pieces of waste paper or cloth which looks as though they may cause the hose to become blocked 20 Do not clean or store the vacuum cleaner in places where there are high temperatures 21 Store the vacuum cleaner away from excessiv
18. uit and has a grounding attachment plug that looks like the plug illustrated below Make sure that the appliance is connected to an outlet having the same configuration as the plug Grounded Outlet 8 1 Grounding Pin NAMES OF EACH PART Handle HosA Power Cord U C Q O D lt Sy Z N Plug Release Plug shown in figure ButtonA may differ from actual Power Cord Ko 7 Release plug attached to unit Carrying Handle Button B for your area Duster Knob ON OFF Switch Cord Storage A eS Hooks aa fal La T EN Dust RE l Compartment Nt j Crevice Tool A Hose al Holder j Wand Suction N Hose B Upholstery Tool amp lt DSN Dusting Brush 5 Q 4 Handle Release p Height Adjustment Lever Holder Rug Floor Tools Lever Headlight Mount SELECTOR X Set the ON OFF switch to ON to light the headlight Extra Hose Pet Hair Attachment Adapter Pet Hair Attachment Cleaning Utensil WARNING Operate vacuum cleaner only at the voltage specified on name plate PREPARATIONS BEFORE USE Caution Do not connectthe power cord plug to the wall outlet until assembly is completed Attaching the handle Set the vacuum cleaner Insert the handle to the upright position as shown in the illustration Suction HoseA Hose Cuff Suction Inlet Crevice Tool Upholstery Tool amp Dusting Brush PREP ARA TIONS BEFORE USE
Download Pdf Manuals
Related Search