Equator MJ-9000VG Washer/Dryer User Manual
Contents
1. 2 Pull the tab on the HEPA dust bag holder out slightly and flip upwards Fig 22 3 Holding the HEPA dust bag in your hand slide it out from the slots in the bag holder Hold carefully in order to avoid having dust fall out of HEPA dust bag Fig 23 Dust Bag Holder Canister Lid Tabs Attaching the Flexible Hose to the Vacuum The flexible hose should be connected to the vacuum before strapping the unit to your back 1 To connect the flexible hose into the hose inlet insert the threaded end of the flexible hose into the hose inlet and turn counter clockwise until it locks into place Fig 6 Fig 6 2 Plug the power cord into the electrical outlet 3 To remove the flexible hose unplug the power cord and then turn the hose clockwise and pull the flexible hose out Attaching the Telescopic Tube to the Flexible Hose Handle 1 Holding the telescopic tube insert the handle into the telescopic tube receptacle Push the handle in Fig 7 SP ima Fig 7 2 Push forward on the plastic button and pull the inner tube outward to extend for a longer reach Fig 8 A lI mr Plastic Button Telescopic Tube OPERATING INSTRUCTIONS 3 To remove the telescopic tube from the flexible hose press on the telescopic tube release button and pull it out Fig 9 Release Note Always remove the power plug from the wall outlet before assembli2. ORDERING REPLACEMENT PARTS Please Note The HEPA pre motor and exhaust filters may be washed We recommend that this be done once a month or when suction appears reduced To wash your HEPA pre motor filter and exhaust filter hold and rinse under lukewarm water When finished shake off For Model BPV325H Call 1 800 798 7398 Eastern Standard Time TO ORDER REPLACEMENT BAGS Item XHB325H Monday to Friday 8 30 A M 5 00 P M excess water DO NOT wash in dishwasher It is important that when you wash any filter you allow it to air dry COMPLETELY before using again We recommend 24 hours to air dry DO NOT DRY IN DRYER IMPORTANT Both the HEPA pre motor filter and the exhaust filter should be re placed every three 3 to six 6 months depending on usage All filters the shake out bag and HEPA dust bag should be checked regularly for signs of damage preferable after each cleaning task The HEPA dust bag shake out bag and filters must be replaced immediately if they become damaged Always disconnect the vacuum from the electrical outlet when checking the filters NEVER re use the HEPA dust bags Always replace the dust bags with new ones 11 OPERATING INSTRUCTIONS Warning To reduce the risk of electric shock the power cord must be disconnected before removing the dust bag shake out bag changing the filters or performing maintenance or trouble shooting checks The HEPA pre motor filter should be replace
3. all controls before plugging or removing filters unplugging vacuum cleaner into electrical 2 To reduce the risk of electric shock do outlet not use outdoors or on wet surfaces 15 Use extra care when vacuuming on stairs 3 Do not allow children to use as a toy 16 Do not pick up flammable or Close attention is necessary when used combustible materials lighter fluid by or near children gasoline kerosene etc or use in the 4 Use only as described in this manual Use presence of explosive liquids or vapor only manufacturer s recommended 17 Do not pick up toxic material chlorine attachments bleach ammonia drain cleaner etc 5 Do not use with damaged cord or plug 18 Do not use in an enclosed space filled Do not use vacuum cleaner if it has been with vapors given off by oil based paints dropped damaged left outdoors or paint thinner moth proofing substances dropped into water Return appliance to flammable dust or other explosive or EURO PRO Operating LLC for toxic vapors examination repair or adjustment 19 Use only on dry indoor surfaces 6 Do not pull or carry by cord Do not use 20 Do not use for any purpose other than cord as a handle close a door on cord described in this user s guide or pull cord around sharp edges or 21 The use of an extension cord is not corners Do not run appliance over cord recommended Keep cord away from heated surfaces 22 Do not put any objects into openings 7 Do not unpl
4. model number and what you believe is the problem with item We recommend you insure the package as damage in shipping is not covered by your warranty Mark the outside of your package ATTENTION CUSTOMER SERVICE We are constantly striving to improve our products therefore the specifications contained herein are subject to change without notice OWNERSHIP REGISTRATION CARD Please fill out and mail the product registration card within ten 10 days of purchase The registration will enable us to contact you in the unlikely event of a product safety notification By returning this card you acknowledge to have read and understood the instructions for use and warnings set forth in the accompanying instructions Return to EURO PRO Operating LLC 94 Main Mill Street Door 16 Plattsburgh NY 12901 Model BPV325H Appliance model Date purchased Name of store Owner s name Address City State Zip Code Printed in China 12 IMPORTANT SAFETY INSTRUCTIONS When using your Vacuum basic safety precautions should always be observed including the following Read all instructions before using this vacuum WARNING To reduce the risk of fire 13 Do not use without all filters in place electrical shock or injury Use ONLY filters and accessories 1 Do not leave vacuum cleaner un oe by EURO PRO Operating LLC attended when it is plugged in Unplug ailure to do so will void the warranty from outlet when not in use and before 14 Turn off
5. the turbo brush over so that the bottom of it is facing upwards Fig 13 OPERATING INSTRUCTIONS 3 Using your thumb and index finger simultaneously squeeze the locking tabs on either side of the trap door and lift off Fig 14 Doing so will The blower attachments have air bleed holes These air bleed holes help relieve some air pressure so that the attachment does not blow off However should an remove the trap door and allow you increase in air pressure be desired access to the turbine for cleaning simply cover one or more of the air bleed and maintenance purposes Fig 15 holes To use the blower attachments 1 Pull up and hold the exhaust tab with the free hand pull out the exhaust grill Fig 16 Fig 16 2 Hemove the exhaust filter 3 To place the blower port into the exhaust outlet align the lower tabs on the blower port with the slots on the exhaust Pull up on the exhaust tab and push the top of the blower port until it snaps into place Fig 17 Fig 15 4 There may be some dust lint hair etc on the turbine wheel Remove as much of this as possible 5 You may also use the unit s hose with the crevice tool attached and use the vacuum to remove any additional debris from the turbine 6 Ensure that the turbine wheel moves freely by rotating it with your finger If the turbine does not rotate call EURO PRO Customer Service for help at Exhaust Tab 1 800 798 7398 Onc
6. to the cost of the repair or replacement of the unit at our option This warranty does not cover normal wear of parts and does not apply to any unit that has been tampered with This limited warranty does not cover damage caused by misuse abuse negligent handling or damage due to faulty packaging or mishandling in transit This warranty does not cover damage or defects caused by or resulting from damages from shipping or repairs service or alterations to the product or any of its parts which have been performed by a repair person not authorized by EURO PRO Operating LLC This warranty is extended to the original purchaser of the unit and excludes all other legal and or conventional warranties The responsibility of EURO PRO Operating LLC if any is limited to the specific obligations expressly assumed by it under the terms of the limited warranty In no event is EURO PRO Operating LLC liable for incidental or consequential damages of any nature whatsoever Some states do not permit the exclusion or limitation of incidental or consequential damages so the above may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state or province to province Important Carefully pack item to avoid damage in shipping Be sure to include proof of purchase date and to attach tag to item before packing with your name complete address and phone number with a note giving purchase information
7. valve while the vacuum exhaust is pumping air into the inflatable 7 To detach the flexible hose turn clockwise and pull out from blower port Note Firmly hold the flexible hose by the attachment when blowing dirt or dust off of objects Using Your Vacuum Warning To reduce the risk of electric shock the power cord must be disconnected before removing the dust bag shake out bag changing the filters or performing maintenance or trouble shooting checks 1 2 3 Insert the power plug into the wall outlet Connect hose and telescopic tube if desired Correctly place shoulder straps on each shoulder and secure the waist band with hook and loop strips Fig 20 Caution If the waist band and both shoulder straps are not properly and securely in place the unit could fall off your back causing damage or injury Shoulder Shoulder Strap Strap Waist Band amp Tool Storage Fig 20 4 Turn the unit on by pressing the switch located near the base of the unit to turn the vacuum cleaner on Fig 21 Fig 21 Removing amp Replacing HEPA Dust Bag To remove the HEPA dust bag from the vacuum Important DO NOT use the vacuum without all filters shake out bag and with or without HEPA dust bag in place 1 To remove the HEPA dust bag press on the canister lid tabs on each side of the unit and lift canister lid Fig 22 Canister Lid Tabs O PL j Ii T Fig 22
8. COPYRIGHT EURO PRO OPERATING LLC 2006 EURO PRO X Commercial Back Pack Vacuum OWNER S MANUAL Model BPV325H 120V 60Hz 12 Amps FOR HOUSEHOLD OR COMMERCIAL USE USA EURO PRO OPERATING LLC Canada EURO PROOPERATING LLC 94 Main Mill Street Door 16 4400 Bois Franc Plattsburg NY 12901 St Laurent QC H4S 1A7 Tel 1 800 798 7398 EURO PRO X BPV325H ONE 1 YEAR LIMITED WARRANTY EURO PRO Operating LLC warrants this product to be free from defects in material and workmanship for a period of one 1 year from the date of the original purchase when used for normal commercial or household use subject to the following conditions exclusions and exceptions Should your appliance fail to operate properly while in use under normal commercial or household conditions within the warranty period return the complete appliance and accessories freight prepaid to U S EURO PRO Operating LLC 94 Main Mill Street Plattsburgh N Y 12901 Canada EURO PRO Operating LLC 4400 Bois Franc St Laurent Quebec H4S 1A7 If the appliance is found to be defective in material or workmanship EURO PRO Operating LLC will repair or replace it free of charge Proof of purchase date must be included Non durable parts including without limitation filters rotating brushes dust bags and electrical parts which normally require replacement are specifically excluded from warranty The liability of EURO PRO Operating LLC is limited solely
9. ath of least resistance for electric current to reduce the risk of electric shock This appliance is u with a cord having an equipment grounding conductor and grounding plug The plug must be inserted into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances WARNING Improper connection of the equipment grounding conductor can result 9 rersox in a risk of electric shock Check with a qualified electrician or service person if you _ G0 are in doubt as to whether the outlet is properly grounded Do not modify the plug v provided with the appliance if it will not fit the outlet have a proper outlet installed gp by a qualified electrician This appliance is for use on a nominal 120 volt circuit and has a grounding EE BLADE attachment plug that looks like the plug illustrated at right Make sure that THREE BLADES the appliance is connected to an outlet having the same configuration as the plug No adaptor should be used with this appliance 1 Rev 06 06A PRECAUTIONARY MEASURES Important If the suction opening of the unit the hose or the extension tubes are BLOCKED switch off the vacuum cleaner and remove the blocking substance before you start the unit again 1 Before inserting the power plug into the wall outlet make sure that your hands are dry 2 Before you start vacuuming make sure to remove large or sharp objects that might dama
10. aution Do not use pet hair remover brush on delicate or woven fabrics that may snag DO NOT use pet hair remover brush on wooden floors as this accessory might cause mild scratching Blower Attachments The blower attachments can be used with the vacuum to pick up very fine dirt particles in tight crevices or spots or to inflate inflatable items or air mattresses dad Using the Air Driven Turbo Brush Warning To reduce the risk of electric shock the power cord must be disconnected before removing the HEPA dust bag the shake out bag HEPA pre motor filter changing the filters or performing maintenance or troubleshooting checks The efficiency of your air driven turbo brush depends on the bristle brush rotating at high speed Strong air suction is needed to accomplish this In order to ensure that maximum air suction is maintained please read the following instructions 1 Change the HEPA dust bag or empty the shake out bag frequently 2 Replace the pre motor and exhaust filters as needed 3 Ensure that the rotating brush is kept free of hair and string which may accumulate and decrease brush performance 4 To attach the air driven turbo brush insert the telescopic tube into the air driven turbo brush How To Clean the Air Driven Turbo Brush From time to time the turbine of your air driven turbo brush will require cleaning To do this 1 Remove the turbo brush from the telescopic tube 2 Flip
11. canister lid onto the vacuum Warning Never over fill the HEPA dust bag replace when bag is full and clean the shake out bag and filter each time the HEPA dust bag is replaced Cleaning amp Replacing the Shake Out Bag Note Clean the shake out bag out doors when changing the HEPA dust bag Optimum performance is achieved by using the HEPA dust bag with the shake out bag decreasing the need for washing the shake out bag Cleaning the Shake Out Bag when Used with the HEPA Dust Bag 1 Remove the shake out bag holding the handle at the bottom of the bag shake outdoors vigorously over a garbage receptacle until there is no more dust 2 Inspect shake out bag regularly for tears or damage Replace shake out bags if damage or tears are present Cleaning the Shake Out Bag when Used Alone It is recommended that the shake out bag be washed after it has been used several times without the HEPA dust bag in place 1 Remove the shake out bag empty contents into a trash can and shake vigorously outdoors until there is no more dust 2 The shake out bag is hand washable in lukewarm water 3 Allow to air dry for 24 hours The shake out bag should be replaced when needed Never replace into the vacuum if still wet Note If used often without HEPA dust bag replacement and washing will be required more often 4 Replace clean shake out bag in unit and replace the canister lid onto the vacuum Clean
12. d every three 3 to six 6 months to ensure peak performance of your vacuum Changing amp Cleaning the Exhaust Filter Note The exhaust filter is located in the front of the vacuum Important Note This filter is a washable filter and can be cleaned by rinsing under lukewarm water Always allow the exhaust filter to air dry for 24 hours before replacing in the vacuum Do not use a hair dryer to dry it Air dry only To remove the exhaust filter 1 While pushing up the exhaust tab pull out the exhaust grill Fig 25 Exhaust Tab Fig 25 2 Remove the exhaust filter 3 Clean the exhaust filter by rinsing under lukewarm water 4 After air drying for 24 hours replace into the vacuum 10 Motor Thermostat Important This unit is equipped with a motor protective thermostat If for some reason the vacuum cleaner should overheat the thermostat will automatically turn the unit off Should this occur e Turn the unit off e Disconnect the plug from the power source e Check the source of overheating problem i e clogged hose full dust bag or filter e Wait at least 45 minutes before attempting to reuse the vacuum e After unit has cooled down for 45 minutes plug in the cleaner and turn the unit on The vacuum should start again fthe vacuum still does not start contact customer service at 1 800 798 7398 GETTING TO KNOW YOUR BACK PACK VACUUM Main Unit Exhaust G
13. e clean replace the trap door of the turbo brush Ensure that it clicks To attach the hose to the blower port align the flexible hose and turn counter clockwise until it stops The into place Using the Blower Attachments The blower attachments are extremely useful for vacuuming in hard to reach crevices and small compartments such as in cars Important Note When blocking the air bleed holes grasp the blower attachments firmly so that they do not blow off Note Do not use blower function to clear dust off of fragile or delicate objects unless they are secured or held firmly in place as the blower action is quite strong and could cause damage hose is now securely in place Fig 18 7
14. ge the dust bag 3 When pulling out the power plug from the wall outlet pull the plug not the power cord 4 Do not pick up anything that is burning or smoking such as cigarettes matches or hot ashes Do not use without all filters and dust bag in place Do not vacuum any liquids Keep hair loose clothing fingers feet and all parts of body away from openings rotating agitator and other moving parts TROUBLESHOOTING GUIDE TROUBLESHOOTING GUIDE PROBLEM POSSIBLE REASON POSSIBLE SOLUTION Motor runs but no suction Turbo brush does not rotate or rotates slowly Vacuum won t run Hose extension tube or air inlet is blocked HEPA dust bag is full Hose not assembled to hose inlet properly Rotating brush or elbow obstructed Beltis broken Hose is obstructed HEPA pre motor filter is blocked Not firmly plugged in No electricity in wall outlet Blown fuse tripped breaker Motor thermostat may have tripped 1 2 3 Check for blockage remove blockage Replace HEPA dust bag Insert hose into hose inlet and turn counter clockwise until it locks into place Clear obstructions Call 1 800 798 7398 Clear obstruction Clean HEPA pre motor filter Plug unit in firmly Check fuse or breaker Replace fuse reset breaker Turn vacuum off and unplug from outlet Allow unit to cool down before trying to switch on again
15. ing the HEPA Pre Motor Filter Important Please Note The HEPA pre motor filter will stop most of the tiniest dust particles and airborne allergens from re entering the air you breathe In fact it stops 99 97 of all particles as small as 0 3 microns many times smaller than a human hair Because of this incredible filtration performance the HEPA pre motor filter will accumulate many fine dust particles that are difficult to see Be assured that the HEPA pre motor filter is doing the job Clean the HEPA pre motor filter after each use as described in this section 1 Remove the shake out bag from the canister The HEPA pre motor filter is located underneath the shake out bag To remove the HEPA pre motor filter lift the filter from the sides of the HEPA filter 2 Vigorously TapClean the HEPA pre motor filter on a hard surface to remove any residual dust that might still be on the HEPA pre motor filter 3 You can wash the HEPA pre motor filter by running it under the tap and allowing the water to run on the dirty side at least once a month or when suction appears to be decreased Wash once a month or when suction appears reduced Warning Allow 24 hours for drying before replacing in unit OPERATING INSTRUCTIONS 9 6 To blow up inflatable items select the appropriate size blower attachment that will fit into the air valve Fig 19 Fig 19 Turn the unit on and hold the blower attachment and air
16. ng or removing accessories Manual Suction Control Your vacuum cleaner includes a manual variable suction control on the flexible hose handle The suction power can be adjusted by moving the suction regulator to the desired position between Open and Closed Fig 10 Open gives you less suction closed maximum suction For example less suction is required on upholstery and draperies compared to thick carpets which require maximum suction Fig 10 Using the Floor to Carpet Brush 1 To attach the floor to carpet brush to the telescopic tube insert the telescopic tube into carpet to floor brush Fig 11 Floor to Carpet Brush 4 Fig 11 OPERATING INSTRUCTIONS 2 Step on the floor to carpet selector to adjust the height of the brushes There are two 2 different heights one for floors and one for carpets Fig 12 Floor to Carpet selector Fig 12 3 To remove the telescopic tube from the floor to carpet brush pull the telescopic tube out from the floor to carpet brush Using the Attachments Dusting Brush The dusting brush is used for the furniture corners baseboards and between cushions Pet Hair Remover Brush The pet hair remover brush is used for upholstery The unique surface makes it an excellent tool for removing unwanted pet hair Crevice Tool Use for radiators crevices Note This tool is not a grooming tool and should not be used on animals C
17. rill On Off Power Switch Canister Lid Tabs Waist Band Shoulder Straps Back Board Panel Carry Handle Hose Inlet Canister Lid Flexible Hose Flexible Hose Handle Variable Suction Control Telescopic Tube Release Button Technical Specifications Voltage 120V 60Hz Power 12 Amps OSS eS L mb I lk pore ro 15 16 17 18 19 20 21 22 23 24 25 26 27 28 Telescopic Tube Waist Band Back Support Panel Waist Band Tool Carrier Dusting Brush Crevice Tool Blower Port Pet Hair Remover Floor to Carpet Brush Air Driven Turbo Brush Blower Attachments x3 HEPA Dust Bag Shake Out Bag HEPA Pre Motor Filter Exhaust Filter Note Illustrations may differ from actual product OPERATING INSTRUCTIONS OPERATING INSTRUCTIONS Warning To reduce the risk of electric shock the power cord must be Warning To reduce the risk of electric shock the power cord must be disconnected before removing the dust bag shake out bag changing the filters or performing maintenance or trouble disconnected before removing the dust bag shake out bag changing the filters or performing maintenance or trouble shooting checks shooting checks Assembling Your Vacuum Cleaner Note Always remove the power plug from the wall outlet before assembling or removing accessories Inserting the HEPA Dust Bag Note This unit can be used with the shake out bag alone however it must be cleaned after ever
18. ug by pulling on cord To Do not use with any opening blocked unplug grasp the plug not the cord Keep free of dust lint hair and anything 8 Do not handle plug or vacuum cleaner else that may reduce air flow with wet hands 23 Always store your appliance indoors in 9 Do not use the vacuum cleaner to pick a cool dry area up large objects or objects that are likely 24 Keep your work area well lit to damage the vacuum cleaner 25 Do not immerse the vacuum into water 10 Keep hair loose clothing fingers feet and or other liquids all parts of body away from openings 26 Keep end of hose wands and other rotating agitator and other moving parts openings away from your face and body Do not operate cleaner in bare feet or 27 To avoid damaging the carpet keep the when wearing open toe shoes vacuum cleaner head moving at all times 11 Do not pick up hot coals cigarette butts 28 Connect to a properly grounded outlet Mas or any hot smoking or burning only See grounding instructions objects Warning The power cord on this product 12 Do not pick up hard or sharp objects contains lead a chemical known to the State such as glass nails screws coins etc of California to cause birth defects or other reproductive harm Wash hands after handling SAVE THESE INSTRUCTIONS For Household or Commercial Use Only GROUNDING INSTRUCTIONS Is appliance must be grounded If it should malfunction or breakdown grounding provides a p
19. y use if there is no HEPA dust bag installed Important DO NOT use the vacuum without all filters shake out bag and with or without HEPA dust bag in place 1 Unplug the hose connecting power cord and remove the flexible hose 2 To open the canister lid press on the canister lid tabs on each side of the unit and lift canister lid Fig 1 r Canister e o Lid _ Tabs Canister Lid Tabs 3 Pull the tab on the HEPA dust bag holder out slightly and flip upwards Fig 2 4 Holding the HEPA dust bag in your hand slide it firmly between the slots in the bag holder Fig 2 Fig 1 5 The cardboard face of the new bag should rest securely in the dust bag cover guides Fig 3 Fig 3 6 Ensure that the shake out bag is in place Fig 4 Fig 4 7 Flip the HEPA bag holder over pressing the tab on the bag holder until it clicks then replace the canister lid 8 The canister lid can be replaced on the unit with the hose opening on the right or left as per your preference Fig 5 Left Handed Placement Right Handed Placement Fig 5 4 Replace the HEPA dust bag with a new bag Do not reuse the same bag 5 The cardboard face of the new bag should rest securely in the dust bag cover guides Fig 24 Fig 24 6 Replace the shake out bag into the vacuum 7 To replace the HEPA dust bag holder flip the holder and press tab until it clicks 8 Replace the
Download Pdf Manuals
Related Search