Enerco 4000ID Electric Heater User Manual
Contents
1. ENNHD 1GS 3 5 SATA HDD Network Storage Enclosure User s Guide FCC Certifications cE This Equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation CE Mark Warning C 3 This equipment complies with the requirements relating to electromagnetic compatibility EN 55022 Class B for ITE the essential protection requirement of Council Directive 89 336 EEC on the approximation of the laws of the Member States relating to electromagnetic compatibility Company has an on going policy of upgrading its products and it may be possible that information in this document is2. Printers and Faxes 7 Set up a home or small office network 4 View workgroup computers Other Places gy Workgroup 4 My Computer o My Documents B Shared Documents 2 Printers and Faxes Details 22 Management Guide Read this chapter to understand the management interface of the device and how to manage the device Starting the Graphic User Interface GUI The Graphic User Interface GUI is the management interface of this device Most parameters and settings are configured over the GUI To get access to the GUI 1 Double click the shortcut on your desktop to start the PNMD Note To get instruction installing the PNMD please see Installing the PNMD Open WEB Li 2 ThePNMD window pops up Select your NAS and click the button 3 When the Enter Network Password window pops up Enter Network Password E i ay Please type your user name and password enter a user name and Site 19216811 password Ream Network HardDisk UserName admin ii aas 4 Click OK The GUI Opens Note 1 The default user name and password is admin admin To change the username password please refer to Administrator Administrator Setting 2 Both the User Name and Password are case sensitive and alphanumeric 23 Using the Graphic User Interface GUI This section provides an introduction to the GUI Understanding the GUI The GUI is consisted of the foll
3. to execute 6 You may also click the Status button to check the download information File Download Configuration File Download es ee E ee ee ee ee rrr E a a values are ten from network E 46 Maintenance The Maintenance page allows users to Backup download the configuration status of the device Select Code Page for the device Upgrade the device firmware Restart the system Reset factory default Se SY Apply Character Set and UP amp P function to the device To open the Maintenance page click the Maintenance on the configuration categories list Upload Download Your Configuration The Upload Download configuration column allows users to backup and download the configuration status of the device Backup the Device Configuration Status 1 Click the Download button 2 The File Download dialogue window pops up click Save File Download Tou are downloading the tle contig tgz from 10 10 7182 Would wou like to open the file or sawe it to your computer Cancel More Info IY Always ask before opening this type of file 3 Specify a folder to place the downloaded data and click Save Click Close to complete 47 Reload the Device Configuration Status 1 Click Browse and locate the file that you backup before Note To know how to backup the configuration status see Backup the Configuration Status 2 Click Upl
4. Add User Setting User Name fark Hew Password eer Confirm Password es User Description fae _ FTP Access ves No a Then the FTP Access is enabled this useris allowed to tip this device 2A password that defers to the User Mame is Hote recommended 3 Description is limited to 48 characters 4 User Name and password are limited to 16 characters 3 Click apply to add the new user To delete a user 1 Select the user that you are going to remove from the device Mark the check box of the user 2 Click the Delete button to remove the user 40 Group Group Configuration The Group page allows users to Add groups Delete groups e Modify group properties Group Configuration Hote Click Add to add a new group Click Delete to remove the group you selectfroam the list Click the group icon to change the group name description and user To add a new group 1 Click Add button 2 Configure the properties for this group Group Name Enter a group name as the group ID O 15 characters Note The group name must be started with an alphabet Group Description Fill in description as a note for the group 0 48 characters Authorized Users Select group members by marking the check boxes 4 Add New Group Group Name Market Group Description MarketDepartment ne Group Mame is limited to 15 characters ge A Note Discription is limited to 48 characters
5. TA Characters allowed a z A 0 91 g The first letter of your group name should not be a number ED Es E Authorized Users m A h admin 3 Click Apply to add the new group click Undo to reload previous configuration and click Back to return to group list To delete a group 1 Mark the check box of the group that you are going to delete 2 Click Delete to remove the group or click Back to return to group list harket WarketDepartment To configure a group 1 Click the icon of the group to configure Sales Department 2 Modify the properties for the group Click Apply to execute the modification click Undo to reload previous configuration or click Back to return to group list Note For more information about the items please see To Add a New Group 42 Option The Option page allows users to 1 Configure FTP settings 2 Ensure the device security by IP and MAC filter 3 Download files with this device To open the Option page click Option on the configuration categories list FTP FTP Configuration The device embeds a FTP server that allows users to access this device by FTP client To setup the FTP server properties please refer to the following table and click Apply to execute your settings Enable FTP Server Click Yes to enactive the FTP server function or click NO to disable it Port Number The Port number of the F
6. DHCP enable disable and Jumbo mode selecting To change the administrator name and password To set up the system time zone synchronize time and assign a timeserver for the device To add a new user delete a user setup user authorities and change user properties To make users in groups Add users to groups or delete users from groups Change FTP properties including Maximum unit number Port number Timeout setting and 24 Maintenance Web Server USB eSATA Security IP Security MAC File Download Maintenance Web Server Detail Disk Setup enable disable anonymous access To configure the allowed or denied IP addresses for getting access to the device To configure the allowed or denied MAC addresses for getting access to the device To add delete download tasks or change download task properties Provides device maintenance including backup the status of your configuration to the device select code page firmware upgrade system restart resetting factory default configure sleeping mode shut system down and load extended firmware To change the Web server prosperities Shows the USB device information that currently connected to the device To setup or remove the USB eSATA device that connected to the device 25 Status The Status page shows the following information of the device To open the Status page click the Status on the configuration categories list Items Information Host n
7. PNMD scanning the device again Connect your PC and Network HD to your network device Switch or HUB The Ethernet LED will be on once Network HD is connected to network as the picture shown above Then you can click Next to proceed Exit Previous Version v2 2 2006 06 20 4 After scanning the menu shows the NAS in your LAN You may click the Rescan NAS button to search for NAS in your LAN again 19 Drive zi Host Name HD Model Name IP Address HD Capacity Subnet Mask HD Available Size Default Gateway HD Available lf you can not find your NAS please check again and cilck Rescan NAS button Firstly select the NAS you want Then you can do this to your NAS click Open Share to view all shares click Open WEB UI to open management WBB click Configure or Next to configure network setting Rescan NAS Configure Exit Version v2 2 2006 06 20 5 The window shows the connection status of the NAS in your LAN You may click on each NAS to get detailed information of each NAS Select the NAS that you are going to connect to and click the Configure button Note The device cannot detect your hard drive if your hard drive is not formatted as EXT3 format It shows no capacity on this widow To format your HD please refer to HD Format after accessing the device Host Name Drive HD Model Name IP Address 192 168 1 1 HD Capacity OMB Subnet Mask 255 255 255 0 H
8. printer came with an installation disk click Have Disk IF your printer i not listed consult your printer documentation for a compatible printer Printers E This driver i digitally signed Tell me why driver signing is important Cancel 11 The printer is ready for use now Printer name EE Properties Status Idle Find Printer Type HP Deskjet 5700 Series where C Print ta file Comment Manual duplex gt Page range gt Slopies i All Number of copies 1 t Current page Selection C Pages W Collate Enter page numbers andfor page ranges separated by commas For example 1 5 5 12 Print what Document p l l Pages per sheet fi age Print All pages in range 4 a wi Scale to paper size No Scaling ll cose 56 Clean Printer Job Queue The Clean Printer Job Queue allows users to clean the pending print jobs that wait for printing To perform cleaning printer job queue click the Execute button and click Yes to confirm Clean Printer Job Queue Delete Print Queue By clearing the print queue ofthe devices all current and pending print jobs willbe deleted and need to be resentto the printer to complete The process cannot be stopped once ithas begun 3J Appendix Using EZIP Backup to back up your files This program helps users to backup the files on you computer to your NAS Those back upped files are going to be compressed
9. you connect the cable correctly between this product and your eSATA device O Power off this product and your eSATA device Power on your eSATA device first and then power on this product Please note that you should always turn on your eSATA device first 62 Product Specification Standard IEEE 802 3 IEEE 802 3u IEEE 802 3ab Supported Protocol TCP IP HTTP SMB FTP DHCP uPnP Support concurrently connected Users 32 users Interface One 10 100 1000Mbps RJ 45 Ethernet port 2 USB 1 1 2 0 ports One eSATA connector One USB backup button One Factory Default Setting Button One Power On Off Switch Button Connection speed 10 100 1000 Mbps Support Hard Disk Drive One 3 5 SATA interface HDD up to 750G Diagnostic LEDs Power Blue LAN Green Amber HDD Amber eSATA Amber USB I USB II Green HDD Full Red Backup Amber Dimensions 209x135x72 mm Operating Temperature Operating O 40 Storing 10 65 Power Supply DC 12V 3A External power adapter Certification FCC CE VCCI Class B 61NB 02310 217 C 63
10. 1 Click the Add button on folder list E E NewShare Share to All Aan Delete Note Click Add to add a new folder Click Delete to remove the folder you have selected from the list Click the folder icon to change the folder name description and user authority 2 Specify a folder name and description for the newly added folder Click Apply to enable Note e Folder Name 0 15 characters The name for the folder e Description 0 48 characters A note for the folder e Both folder name and description are alphanumeric e Blank character is not allowed for folder name and description Folder added Folder Name Video Description VideoP les all 1 Folder Mame is limited ta 15 characters Discription is Hote limited to 46 characters 2 Characters allowed a zA 2 0 9 1 3 f4 31 3 Setup the folder properties and click Save to apply Note For detail folder configuration see To configure folder properties To Delete a Folder 1 Mark the check box of the folder that you are going to delete 2 Click Delete to delete the folder Back Hote Click Add to add a new folder Click Delete to remove the folder you have selected from the list Click the folder icon to change the folder name description and user authority Disk HD Configuration To format your hard disk in EXT3 format 1 Click Yes to execute HD Format 2 Start formatting afte
11. 2 You can change the user s properties by modifying the settings on each item User Name Specify a name for the newly added user 4 16 characters New password Enter a username for the new user 4 16 characters Confirm Password Enter the new password again to confirm the password 4 16 characters User Description Fill in a description as a note for the user O 47 characters FTP Access Click Yes to allow this user to access the device with FTP client Click No to deny FTP access Note The username and password for accessing the FTP server are the same with the one that configured above 38 User jeff setting User name jef New password pe Confirm Password i gt User Description BE FTP access amp Yes No The maximum length of password is 16 Hote Control character is not allowed in username The maximum length of description is 48 3 To change the user name click the Change Name button The change username page shows up Fill in the new user name in the New User Name box Click Apply to execute Change User jetf Name Setting Old User name jeff New User name jeff222 The maximum length of username is 16 Control character is not allowed in username To Add a New User 1 Click the Add button on the user list 2 Define the user properties Note For more information about each item see To Configure a User 39
12. B orreri a E 52 DECA ee E E A E 52 DISK SCUD noueis a N 52 USB Storage information sssssrererererrrrrrrrrsrsrsrsrsrererne 52 Pinter SEUD ee Pe eee re 53 Procedures to setup the printer s sesererererererrrrrrrrrrrrro 53 Clean Printer Job QU UC ccnn 57 USING EZIP BACKUP TO BACK UP YOUR FILES 58 TROUBLE SHOOTING sancetacsenicontencet i nanweteiie nose enioen 60 PRODUCT SPECIFICATION ccccccececeeueueuevevevevevavevares 63 Overview Thank you for purchasing the product Read this chapter to know about your Gigabit SATA NAS with USB Unpacking information Before getting started please verify that your package includes the following items 1 One Gigabit SATA NAS with USB 2 One Power adapter and one AC power Hard Disk not Included cable 3 One Quick Installation Guide 4 One Utility Manual CD 5 HD Fastening screw x 4 Introduction to the GIGABIT SATA NAS with USB Easily back up your data and share them this Gigabit SATA NAS with USB is a high speed economical powerful NAS Network Attached Storage using the efficient SATA interface and providing an excellent data storage and sharing solution for your small business SOHO Small Office or Home Office or personal requirement You may also back up those files from your USB storage devices with pressing the Backup button Embedding FTP server and Web Server The FTP server allows users to backup and share files with FTP clien
13. C Address 5 MAC Address 6 MAC Address 7 MAC Address 9 MAC Address 9 MAC Address 10 45 File Download File Download Configuration The File Download page allows users to download files with this device Note Before using this function you should load the ntx_libra tgz first To get information for installing the ntx_libra tgz file please see Load firmware extensions The instruction below uses the following assumptions The address for downloading http www example com downloads sample file The authorized account name peter Password 12345 The target folder where the downloaded data is going to be placed Share Note The download address account name and password are made up for the example There is no such an address and account To start a download task 1 Fill the address you get for downloading files in the Address box ex enter the address http www example com downloads sample file to the Address box 2 Enter an account name and password in the Account and Password box respectively Ex enter peter in the Account box and 12345 in the Password box 3 Select a folder to place the downloaded data in Save Path drop list Ex Select the folder Share from the drop list Click Apply to perform file download To cancel or terminate a download task click the Del button to erase the download information then click Apply
14. D Available Size OMB Defaut Gateway 192 168 1 254 HD Available 0 lf you can not find your NAS please check again and cilck Rescan NAS button Firstly select the NAS you want Then you can do this to your NAS click Open Share to view all shares click Open WEB Ul to open management WBB click Configure or Next to configure network setting Rescan NAS Configure Exit Version v2 2 2006 06 20 20 6 You may select Auto assign I P Address which allows the PNMD to assign IP addresses for the device or select Use the IP Address as below fill in IP address for this device Enter the username and password and click OK Note The default username password is admin admin To get information modifying the username and password see Administrator Administrator Setting C Auto assign IP Address Used the IP Address as below IP ADDRESS 10 10 7 182 NETMASK 255 255 0 0 Default GateWay 10 10 7 254 The default username and password for WAS are admin and admin User Name admin Password po JK N Cancel 7 After successful IP address setting the PNMD rescans NAS in your LAN automatically 8 Select your NAS You may Open Sh l Click the _Open Share button to access to folders in the NAS or Click the Open wEB Ut button Fill in the username and password and click OK to open the GUI interface Enter Network Fasword l aj
15. InstallShield Wizard for EZIP Backup The InstallShieldA Wizard will install EZIF Backup on your computer To continue click Hest Cancel 16 3 Fill your User Name and Company name in their respective blanks Select if you want this software to be used by anyone who uses this computer or yourself only Click Next to proceed EZIP Backup InstallShield Wizard Customer Information Please enter your information User Name Mark Company Name Home Install this application for Anyone who uses this computer all users Only for me Jeffrey InstallShield 4 Choose the destination folder for this software and click Next to start installation You may click Browse to change the location EZIP Backup InstallShield Wizard Choose Destination Location Select folder where setup will install files Setup will install EZIP Backup in the following folder To install to this folder click Next To install to a different folder click Browse and select another folder Destination Folder C Program Files MAS Utility EZIP Backup Browse InstallShield 5 Click Finish to complete the software installation EZIP Backup InstallShield Wizard InstallShield Wizard Complete Setup has finished installing EZIP Backup on your computer 17 6 After successful installation the IE shortcut shows on your windows des
16. TP server Please fill in a number from 1 to 65535 Time out The allowed time that keeps the FTP server connected with a FTP client The FTP server terminates the connection if the client fails to response during the specified Time Out period Allow Anonymous Allow FTP client to connect with the device without username password authentication Note Please DO NOT use the number 80 as the Port Number As default port 80 is the Administration Port for the device To get more information about the Administration Port please refer to Administration WEB FTP Configuration FTP FTP Setting Port Number fl Timeout i3 Minutes Allow Anonymous Yes No 1 The maximum number of unitis upto 5 when SWAF disable Hote Tou enable SWAF function the maximum number will th to 32 2 The portnumberis between 1 and 65535 43 Security IP IP Filter Setting The Security IP function provides access management by IP address filtering There are three modes for the IP filter 1 Disable Disable the IP Filer function All IP addresses are allowed to access the device 2 Allowed Setup the IP addresses that are allowed to access the device Only the configured IP addresses have the right to access the device 3 Denied Setup the IP addresses that are denied to access the device The IP addresses that are configured are not allowed to access the device Tip For example to prevent the IP address 192 168 1 3 f
17. USB printer only Printer Connections on both the USB ports may led the printer functioned unsuccessfully 1 Connect the USB cable of your printer to the device Power on your printer 2 Open the GUI and click Maintenance Install the firmware extension file to the device Note To get information for installing the printer server file please see Load Firmware extensions 3 Click USB gt Detail you can see the information of your printer 53 USB Setup Detail USB Class Device Name USB 2 0 1 1 Printer HP Deskjet 5700 USB 2 0 4 Click Printer Setup Click Yes in the Printer enable column and click Apply Note After finishing the four steps above the printer server function is activated To setup the computers that are going to use the printer please follow the instructions from step 5 Print Server Printer port Printer name Printer enable Printer Enable Deskjet 5700 f ves No The option willbe decide printer that driver can be enable or disable Userwillpress apply button to execute driver through printer setting web page Process cannot be stopped once ithas hegun 5 Double click the Shortcut on your desktop to start the PNMD The PNMD Open Share window pops up Select your NAS and click the button 6 You can find a printer icon Double click on this icon to proceed 7 The system asks for installing the driver for the printer Click Yes on the warnin
18. ame The identification of this device I P address The IP address of the device HD used The usage percentage of HD Total amount of HD Up time The estimate time that you power the device on Version The firmware version of the device Samba Users The number of members who is currently using the device by Samba FTP Users The number of members who is currently using the device by FTP client Firmware Check if the extension firmware is installed extensions Loaded eSATA used Check the connected eSATA device usage Note This page shows the device information only To do more configurations about each item please refer to their instruction respectively in the following chapters Status Information Host Name Drive IP Address 10 10 99 146 Static IF HD used h 0 03 156 4 Up Time 13 Minutes Yersion YT 0009 185 2006 Samba Users 0 FTP Users 0 Firmware extensions loaded Yes eSATA used not connected 26 Disk The Disk page allows users to 1 Change the properties of folders 2 Format the hard disk connected to the device with IDE connector To open the Disk page click the Disk on the configuration categories list Folder Folder Configuration The folder configuration allows users to add folders delete folders and change folder properties Folder Configuration Hote Click Add to add a new folder Click Delete to remove the folder you select trom the list Click the folder icon to change
19. as zip format in your NAS Py 1 Double click the 4 ge shortcut on your desktop 2 Click the 8 icon on system tray The EZIP Backup window pops up You may click the 6 button to close this program or click the s button to minimize this window to system tray ae Folder as i ru Menday Fi Tuesday P We ee day Jo Thursday 7 Friday 9 Saturday 58 3 Click PC Folder Select button Browse a folder that you are going to backup and click OK The folder that you selected shows on the list D Wroking Table Wroking T able 4 Click the Change NAS button to select a NAS Select a NAS in the NAS device drop list Select a destination folder for locating the back upped files Apply HAS Eoia I Drive Share 5 Fill in a user name and password for accessing this folder Select the time that you are going to execute backup Click Setting Apply Note You may also mark the Disable Schedule Backup checkbox to disable EZIP Backup to backup your files by schedule Tae Sarees eat hd Fe ai a ARa paia ne P ani a S che dule etting 00 f 00 00 A Sunday Monday Tuesday Password etting Apply Wednesday Thursday Friday Saturday 6 Click the Apply button on the up right corner of the window Backup LLE 7 Click thel button to start backup To restore a back upped file to your PC select the file on the list and click Restore to perfo
20. configured as the IP address of this Device and the value of Port Should be corresponded to the port number of the WEB server or FTP server you configured Ex If the IP address of your device is 10 10 7 251 the port number of your FTP is configured as 21 and the port for Web Server is as 8888 you should add or modify a port mapping record set the Internal Host IP address as 10 10 7 251 the Port as 21 then add or modify another port mapping record set the Internal Host IP address as 10 10 7 251 and the Port as 8888 3 Before allowing the device to communicate with Internet we strongly recommend users to add a Firewall device to secure your network from being invading 60 5 1 can t access this device Ans O Check the LINK ACT LED of Device illuminates O Reboot the system with Web based UI or press the Default Button to restore the Factory default setting and reboot O Maybe there are too many concurrently connected users The system blocks the upcoming users after meeting the maximum allowed number 6 I have accessed the HD but can t access to the folders Ans Oo Verify you have the correct username and password Oo If you have accessed to any folder in the HD and would like to use another set of username password for different authority please log off your operation system and log on again 7 There are unrecognizable characters as the file name Ans Oo Verify if the Unicode file is loaded to the devic
21. e New folder name NewShae 0 D Folder description ohare to All Note Folder name is limited to 15 characters Description is limited to 48 characters 3 The folder name description is replaced successfully You may click Change to do more configurations for this folder or click Back to return to folder list Folder Configuration Folder name MewShare Description ohare to All Change f Back Configure folder accessing authority level for users and groups 1 Configure the access permission rules for all users by pre defined levels Select one level and click Save to apply this authority for all users The pre defined levels use the following access permission rules Pre defined Levels Access Authority Authentication Free No authentication Everyone is allowed to get Access access to this folder without username and password No access for all users No accessing No user is allowed to get access to this folder Only Read access for all All users are allowed to read in this folder users Modification in this folder is not allowed Read Write access for All users are allowed to read and write this folder all users Current Access The folder uses user defined authority settings The Permission for all users access permissions in Group Authority Setting and User Authority Setting will be applied to this folder 29 Please set user s limitfor this folder Authentication Fre
22. e Access No access for all users C Only Read access for all users C ReadMrite access for all users C Current Access Permission for all users 2 Configure the access permission rules by groups and users Note Before starting you have to click Current Access Permission for all users in the Please set user s limit for this folder By Group Mark the checkbox to select an authorized group Select an access permission rule for this group and click Save to apply By User Select an access authority for each user Click Save to apply Flease set user s limitfor this folder Authentication free access No access for all users es Read only access for all users C Readirite access for all users Current access permission for all users Group Permissions setting No access Group applied E Read only Sales Read and write User Permissions setting No access j Read only admin Read and write Tips To do an efficient access authority configuration please refer to the following recommend procedures Stepl Select a Pre defined authority level for all users Ex Click No Access for all users to configure all users as Non access for this folder Step2 Click Current Access Permission for all users to allow configuration 30 by groups or users Step3 Specify the users that have different authorities Step4 Click Save to apply To Add a New Folder
23. e package 6 Place the HD cover back on to the device and screw the cover on Connect this device to your Local Area Network LAN 1 Connect one end of a RJ 45 cable to the LAN port on the device 2 Connect the other end of the cable to your IP sharing router or switch r gt Connect this device to your USB devices The device equips two USB ports that allow users to connect the device to a USB storage device 1 Find the USB cable that came with your USB storage device Insert the USB Type A end of the cable to the device the other end to your USB storage USB Storage USBPrinter Note a The Type A end of the USB cable is usually the end that connects to your computer b If you are connecting an external HD to the USB ports on the device we recommend users to connect the power adapter of the external HD to supply efficient power for your external HD 2 Insert the other end to your USB storage device Connect Your eSATA device to this product The device equips one eSATA port that allows users to connect the device to an eSATA device Please find the cable that came with your eSATA device Connect your device to the eSATA port on front panel ESATA Device Note You have to power your eSATA device on before powering on this product or your eSATA device cannot be detected by this product 12 Power on the device 1 Connect the included pow
24. e successfully To get instruction loading the file please see Load Firmware extensions O Check if you select a correct Code Page in Maintenance 8 1 have followed the procedures to setup the printer and it just doesn t work Ans O Check if you power your printer on O Verify that the cables are connected correctly O Make sure that you enactive the printer server functionality you can refer to Printer setup for more information MO You may select an incompatible printer driver Click Start gt Setup gt Control Panel Double click the printer icon Remove this printer and install a different driver and try again O The device supports one connected USB printer only Printer Connections on both the USB ports may led the printer functioned unsuccessfully 9 1 can t add a new user Ans O This device supports usernames with lower case only Please check if you specify a new user with a capital letter 61 10 1 can t configure the default user admin in User Configuration Ans O The username and password of the user admin can only be configured in the System gt Administrator page Please note that you will have to login the GUI with this new superuser ID and password after changing it O The Superuser ID is also the administrator ID while you access folders in this device via samba or ftp The ID can access all folders in this device 11 My eSATA cannot be detected Ans Oo Verify that
25. er Device Name _USB 2 0 1 1 Printer HP Deskjet 5700 USB 2 0 Disk Setup The Disk Setup page allows users to 1 Get information about the connected USB eSATA device 2 Format the connected USB eSATA storage device 3 Safely remove the connected USB eSATA device USB Storage information Name 1 16 characters Define a name for the USB storage device Note The name is also the folder name that is going to be displayed while access the device form computers Description The partition order of the connected device Note 1 The device recognizes the first four partitions only We recommend users not to format your USB eSATA device for more than 4 partitions 2 The device support one connected USB storage device Only one USB storage device can be recognized while there are two USB storage device connected simultaneously 52 Size The size of the connected storage device Remove button Click this button to safely remove the connected device Format button Click this button to format the connected device in EXT3 file format USB Setup Disk Setup L USB Device Hame Description Size fosbdisk 1 Remove Partition 1 125W6 Format eSATA device Description Partition 1 Note Always disconnect your connected USB or eSATA device by clicking the Remove button To remove your improperly may lead to data loss Printer Setup Procedures to setup the printer Note The device supports one connected
26. er cord with the power adapter SS 2 Connect the connector end to the device and the plug to an outlet rl 3 Push the power button to power on 13 Software Installation Installing the PNMD This PNMD program helps users to get accessed to those NAS in your LAN Please follow the instructions to install the software 1 Insert the CD Rom that came with this product to your CD Rom drive The main menu pops up automatically Click the Install PNMD button to start installation Install EZIP Backup Note If the auto run program is not activated please click on My Computer gt your CD Rom Drive then click the InstallMenu icon to start the main menu 2 Click Next on the welcome window PNMD InstallShield Wizard x Welcome to the InstallShield Wizard for PNMD The InstallShieldR Wizard will install PNMD on your computer To continue click Next E ea 14 3 Fill your User Name and Company name in their respective blanks Select if you want this software to be used by anyone who uses this computer or yourself only Click Next to proceed PNMD InstallShield Wizard f x Customer Information Please enter your information User Name Mark Company Name Home Install this application for Anyone who uses this computer all users C Only for me Jeffrey InstallShield lt Back Cancel 4 Choose the destination folde
27. ereetaseatian 38 TOAGA a NeW USER ssaidincecnelisaidisamhiviadwiskiaviandieenasdee ae 39 TO Qelete a USET sisetniiiaendiieansacmiaareeniiavadeotnunennieassdannaeaaas 40 Group Group CONnfiguratiOn eects 41 To adda NEW OOD waddacecn edit a n 41 To delete a groOUp sssssserererererererrrerrrrrrrrrrerrrrrrrererersrnas 42 TO GONTIGUEG a GOUD eceran cenena aAa 42 OPTION ore A 43 FTP FTP Configuration rrr 43 Security P IP Filter Setting rrr 44 Security MAC MAC Filter Setting 45 File Download File Download Configuration 46 MAINTENANCE ovcacascrcaevedetacsnsduiidaustieanedsededtwercmecsa iments 47 Upload Download Your Configuration ccc 47 Backup the Device Configuration StatuS cee cece eee 47 Reload the Device Configuration StatuS cece cece eee 48 COJE ccc oS ene ere near neem ede Pen ee Rt neem ere ere 48 Firmware Upgrade cccccccccccccesessssssssueueeeeeeeeeeeeeeeeeeens 48 Restart the SySteM cc ccccccceeeeeeeeeeeeeeeeeeeeeeeeeenennanenegs 49 Reset to Factory Default 49 SS 111 CC rite cies aicer capitate emcee 49 System Shut DOWN esssssssseen 49 Load Firmware extenSionS ereere 50 WEB SERVER sicscsnczsicasdsnvnstmducine seatsduossidtersacnonacsoaueduers 51 At al go Vs eee eee nen ey een nen One eee rere 51 Administration WEB si01c6sidusesecn a a aa 51 Web Server Configuration sssssusserrererrrrrrrrrrunurrrrrrrrrrrrrrrrus 51 US
28. function 2 The Backup LED illuminates while data copying Do not remove this device from USB I port before the Backup LED turns off eSATA connector Connect this port with your eSATA device Rear Panel USB Reset to Deafault Button RJ 45 Connector Reset to Default Button Press and hold the Reset Default Button for 4 seconds to reset all configurations to factory default settings Note 1 All configurations that are done by users will be removed from the device 2 The device also supports restoring factory default settings by software To get instruction restoring factory default parameters see Reset to Factory Default LAN Port Connect the port with RJ 45 cable to your switch or IP sharing router Note To get instruction connecting the device to your LAN refer to Making Connection with the Device USB Port Connect this port with your USB Storage devices Power Adapter Socket The socket for connecting the power adapter Installation Guide Hardware Installation Install a Hard Disk Drive for the Device 1 Lie the device down as the following picture Please make sure that the device is oriented correctly 2 Unscrew the screws on both the top and bottom side of the device 10 4 Place the Hard Disk drive evenly on the hard disk drive base Slides the Hard Drive to connect to the connector on the device 5 Secure your hard disk with the included screws in th
29. g dialogue windows to proceed Connect to Printer You are about bo connect to a printer on 1 DRIVE which will automatically install a print driver on your machine Printer drivers may contain viruses or scripts that can be harmful to your computer Ik is important to be certain that the computer sharing this printer is trustworthy would you like to continue EZEN 8 Insert your CD that came with your printer Click the Have Disk Button 54 Add Printer Wizard Select the manufacturer and model of your printer IF your printer came with an installation disk click Have Disk IF your printer ie not listed consult pour printer documentation for a compatible printer Manufacturer Agta Alps Apollo Apple APS PS AST ie This driver iz digitally signed Tell me why driver signing i important Printers i Cancel 9 Browse to the driver in your CD Click Open to browse the driver Tip The correct driver is usually the file with the product name in inf format Locate File Look in HPPP D C Applications My Recent Documents L Desktop My Documents My Computer File name My Network Files of type util 3 Windows E autorun inf i 4 hptS700p inf hpFS 700g inf hpF5700u inf hpt r p int 10 Click the OK button to start driver installation 55 Cancel Add Printer Wizard Select the manufacturer and model of your printer IF your
30. ion is limited to 48 characters 2 Space character control character and are not allowed IP Address IP address Setting To Enable DHCP Client Click Enable to enact this device as a DHCP client and click Disable to disqualify DHCP Client Disable Enable To Configure the IP Addresses for the Device 34 The IP Address Setting contains parameters of the device network setting To modify fill in each blanks and click Apply to execute IP Address Specifies the device IP Subnet Mask Defines the Subnet Mask Gateway Defines the default gateway Primary Secondary Defines the DNS server DNS Server Jumbo Frame Setting Jumbo Frame P Address Setting DHCP Client Disable Enable IP Address poosis OOOO subnetwork Mask 255 255 2550 Gateway pons DNS Server EC Ityou change the DHCP setting the user interface Hote Will be disconnected and anew IP address willbe assigned Apply f Undo Jumbo Mode The device supports Jumbo frame for obtaining a more efficient network You may choose 4000 or 7000 as the size of a packet To select J umbo modes choose a mode from the drop list and click SET to execute Jumbo Frame Disable 35 The System page allows users to i 2 3 4 Configuring Administrator name and password Synchronize system time Add delete and configure a user Add delete and configure a group To open the System page click the System o
31. ith FCC CE Class B certification Front Panel Power Button Power Button LED To activate the device press this Power button for 2 seconds after connecting the device to an appropriate power outlet with the provided power cord To power off press the button for two seconds until Power LED starts to blink LEDs Definition Power LAN HDD eSATA USB USB II HDD FULL Backup Steady Blue Blinking Blue Off Steady Green Blinking Green Steady Amber Blinking Amber Blinking Amber Off Blinking Amber Off Steady Green Off Steady Green Off Steady Red Off Steady Amber Off Power on System starting closing Power off Valid Connection at 1000 Mbps Data transmitting at 1000 Mbps Valid Connection at 10 100 Mbps Data transmitting at 10 100 Mbps Data transmitting on HDD No HDD acting Data transmitting or receiving on eSATA port Invalid connection on eSATA port Valid connection on USB port Invalid connection on USBI port Valid connection on USB II port Invalid connection on USBI port HDD has run out of space Space available on HDD Data copying from USB to internal HD Data copying finished Backup Button Press this button to copy those files from USB port to the internal HD A new folder will be created automatically in the share folder This new folder is named according to the time you press this button Note 1 Only USBI port support this quick backup
32. ktop Note For instructions using the software please refer to chapter Using EZIP Backup to backup your files in Appendix Making Connection with the Device Connecting the device with PNMD 1 Double click the Dw shortcut on your desktop The PNMD begins scanning NAS in your LAN Please click Next to proceed after the Welcome window pops up Note This window pops up only when there is no device detected It guides users to attach cables for the device If the PNMD detects this product successfully the window is not going to appear Please skip to step 4 to continue RSP ALNI Welcome e Pri vide lhe best perf FINANCO and gualily Thank you for using Network HD This Program will assist you with setting up your Network HD s network configuration and create shortcuts for management and accessing on your PC s desktop Please click Next to proceed Version v2 2 2006 06 20 2 Connect the power adapter and press the power button to power on the device Click Next 18 Please plug the power cord into an appropriate power outlet Connect the connector side of the power cord to the device s power connector terminal AC IN Push the Start button on the panel The power status LED will be on and keep blinking during booting and stop blinking after booting process Then you can click Next to proceed Previous Version v2 2 2006 06 20 3 Connect the LAN port to your switch or IP sharing router The
33. n the configuration categories list Administrator Administrator Setting This page provides Administrator Name and password configuration which are used for getting access to the Graphic User Interface To modify the Administrator Name and password 1 Define a Administrator Name 4 16 characters in the Administrator Name box 2 Fill in the original password 4 16 characters in the Old Password box 3 Define a new password 4 16 characters in the New Password box 4 Fill in the newly defined password 4 16 characters in the Confirm Password box 5 Click Apply to execute Note 1 The default Administrator Name and password are admin admin 2 The Superuser ID is also the administrator ID while you access folders in this device via samba or ftp The ID can access all folders in this device 3 The Administrator Name and password are both case sensitive and alohanumeric 4 To enforce the security it is recommended to change the Administrator Name and password periodically Superuser Password Setting Administrator Superuser Setting admin Superuser ID Old Password ere New Password Ea Confirm Password pe Please provide superuser name and password from 4 to 16 Hote characters Periodically change the superuser name and password to ensure security 36 Time System Time Setting The Time page provides time synchronizing function You can synchronize the time by applying the time o
34. n your computer to the device or by connecting to a time server To configure the device time 1 Select the time zone that corresponds to your region from the Time Zone drop list 2 Select if applying Daylight Saving on system time by marking the checkbox or not 3 To apply the time on your computer to the device select Local Time and click Time Sync button 4 To synchronize the time from a time server select Time Server fill in a time server address in the Time Server box and click Time Sync to execute 5 Click Save to apply your configuration or click Back to abort Note the synchronized time will be applied by next reboot To reboot the device please see Restart the System system Time Setting Time System Time Setting Time Zone Taiwan Local Time Sun Jul 28 14 02 05 wx 2002 me syne Time Server O de pool ntp org Clicking Time syne will restart the network daemon such as SAMBA and FTP 37 User User Configuration The User page allows users to Add users Delete users Modify user properties User Configuration Hote Click Add to add anew userwho is allowed to access the Gigabit SOHO MAS Click Delete to remove the user you have selected from the list Click on the user icon to change the username password and description To Configure a User 1 Move the cursor onto the icon of the user that you are going to configure
35. not up to date Please check with your local distributors for the latest information No part of this document can be copied or reproduced in any form without written consent from the company Trademarks All trade names and trademarks are the properties of their respective companies Copyright 2007 All Rights Reserved TABLE OF CONTENTS Os A re UNPACKING INFORMATION ccccccccccccccccccucccuuucceueeeneas 5 INTRODUCTION TO THE GIGABIT SATA NAS witH USB 6 Key FEJ SS raran EAE I NTT names 6 DESIR eae E A TEE E O EE A 7 POWER Butto mssan cloned en a a a a TE NE bene 7 LEDS Defi O A A E AA a a Aan 7 BackUp BUON reece a aa a a 8 ESATA CONNSCEOR ict ws eee ee eet i cio hoot dees 8 Rear Panel EEEE EEEE EEEE EEan 9 Reset to Default Button cccc ccc ccueuccuuncucucvecucucuununneucuasunuanes 9 EAN POT ean nr gene E cen ne er 9 USB POG seori dee toctove ee eect ah coe an ee ees ati nee cine ee cite A 9 Power Adapter SOCKEE asa vunedcaeiiawreiichce EAE ates 9 HARDWARE INSTALLATION ccccccccccccccuccccccuccccccuccas 10 Install a Hard Disk Drive for the Device 0 10 Connect this device to your LAN eee 11 Connect this device to your USB devices 12 Connect Your eSATA device to this product 12 Power ON the device aeara 13 SOFTWARE INSTALLATION ccecccscccsccesccecucecaceeaeers 14 Installing the PNMD cccccccccccceeeeeeeeeeeeeeeeteeetenenneees 14 Ins
36. o save your configuration Note The Port 80 is configured as the default Administrator WEB Server Port Web Server Configuration The device embeds a WEB server that allows users to construct a Website To activate the WEB server 1 Click Yes to enable 2 Specify a port number from 1 65535 3 Specify a WEB Folder where you place your HTML files Note 1 The WEB server supports HTML format only 2 As default the Port 80 can t be setup as the Web Server Port for 80 has been configured as the Administration port 3 Wealso provide a Website template for you to build up a Website and enjoy the WEB server properties easily To use the template insert the included CD copy the data in the folder WEB Template Paste those data in the folder that you configured as the WEB Folder WEB Server Administration WEB Administration Port 20 WEB Server Enable WEB Server C Yes No WEB Server Port 2080 WEB Folder hare r 1 Fot number must pe between 1 and 65535 Hote 2 WEB folder is the location of all your HTML files WEB serer will start from index html if it exists 51 The Detail page shows the information of the connected USB devices USB Class The USB device type Manufacturer The manufacturer of the connected USB device Device Name Name of the connected USB device USB 2 0 1 1 The USB standard supported by the connected USB device USB Setup Detail USB Class Manufactur
37. oad to execute 3 The system restarts automatically to reload your previous configuration Contig Upload or Unlead 5 Download pl DW entie hackup oontig tga TOWSE Downlcad Code Page The Code Page helps this device to recognize correct file name while users access the device via FTP server To apply another code page select a proper code page from the drop list and click Apply to execute Note As default the code page is configured to be corresponding to your region Changing the code page is not recommended unless you got unrecognizable characters on file name or folder name Code Page 850 BO 8859 15 Euro Apply Firmware Upgrade To upgrade the firmware click the Browse button to locate the firmware Click the Update button to perform firmware upgrade Note To get new firmware of the device please contact your distributor for more information Firmware Upgrade Update Browse 48 Restart the System This column allows users to restart the system To perform system restarting click the Restart button System Restart Restart Reset to Factory Default To restore the factory default configuration for the device click the Set to Default button to execute Note 1 All the user defined configurations will be erased and replaced as factory default setting 2 We recommend users to backup the configuration status before restoring factory default To get mo
38. owing components 1 Configuration categories Located on the left side of each page Lists the configuration categories on this device To get access to each category click on the button that you are going to configure 2 Configuration items Located on the right side of each page Shows the items that can be configured You can click on the tabs that listed above to access to each sub categories Note For detail information about configuring each item please refer to the management instruction for each configuration category Management items list The following table lists the information and items that you can configure with the GUI For detail instruction please refer to the following chapter Category Status Disk Network System Option Sub category Status Folder Disk Host IP address Administrator Time User Group FTP Information Shows the status information of this device including Host name IP address HD used percentage system up time firmware version current Samba users and FTP users firmware extension loaded and eSATA connecting status To add a new folder delete a folder change folder access authentication and set up folder properties To format the connected SATA interface hard disk in EXT3 Format To change the device s host name Work group name and description To configure the network settings for the device including IP address Subnet Mask Gateway DNS server
39. r for this software and click Next to start installation You may click Browse to change the location FHMD Installshueld Wizard Choose Destination Location Select folder where setup will install files Setup will install PHMD in the following folder To install to this folder click Next To install to a different folder click Browse and select another tolder Destination Folder C Program Files WAS Utility PMD Browse InstallShield Cancel InstallShield Wizard Complete Setup has finished installing PHM on your computer 15 6 After successful installation the EA shortcut shows on your windows desktop Note For instructions using the software please refer to chapter Making Connection with the Device Installing the EZIP Backup This EZI P Backup helps users to backup files on your computer to NAS Please follow the instructions below to install the software 1 Insert the CD Rom that came with this product to your CD Rom drive The main menu pops up automatically Click the Install EZI P Backup button to start installation Install Menu Install PNMID Exit Note If the auto run program is not activated please click on My Computer gt your CD Rom Drive then click the InstallMenu icon to start the main menu 2 Click Next on the welcome window EAIP Backup Installshield Wizard E X Welcome to the
40. r your confirmation Caution All files within the hard disk will be erased while HD Format is executed Note The Hard Disk will be formatted as EXT3 format HD Format Note lt Supports only EsTa and may take several minutes Please wait and ensure a safe operating environment Note Wren the AD formatis completed it will return to the Home page 32 3 After confirmation for HD formatting the system starts formatting the hard disk It may take several minutes according to the storage size of your hard disk Please wait and DO NOT execute other configuration for this device while formatting Format HO This may take a few minutes Please wait and ensure a safe environment upon performing HO formating Do not close this WTF ow 33 Network The Network page allows users to 1 Configure general device information 2 Configure the network setting for the device To open the Network page click the Network on the configuration categories list Host Host Name Setting Host Name 1 15 characters Define the user defined device name Workgroup 1 15 characters Defines the workgroup name for the device which is going to be shown on Network Neighborhood Description 1 48 characters Define a note for the device Host Name Setting Host Host Name Setting Host Hame fe Work Group Weorkroup Description 1 Host Mame amp york group are limited to 15 characters Hote Discript
41. re information for backup your configuration see Backup the Device Configuration Status Reset to Factory Set to Default Default Sleep mode This device supports Sleep Mode which stops the device temporarily while there are no operating on the device for a certain period of time To enable Sleep Mode click on the drop list to specify a time and click Apply to execute SLEEP MODE 15 mimes Apply System Shut Down To turn off the device click on the shutdown button and wait the device to turn off automatically 49 System Shutdown Shutdown Load Firmware extensions To enable the Unicode and UPNP function for the device you have to install the ntx_libra tgz file to the device before any configuration To install the file 1 Insert the included CD and click the Browse button Note The Install Menu may auto run Click EXIT to close it 2 Right click on your CD Rom drive Select the Firmware Extensions folder Select the ntx_libra tgz file and click Open to browse the file 3 Click Apply to perform installation It takes a few seconds to perform installing please wait upon installation Load firmware Apply E Browse extensions 50 Web Server Web Server Administration WEB The Administration port is the port for accessing the Web based management interface To modify the Administration Port enter a port number from 1 to 65535 then click Apply t
42. rm restoring 59 Trouble Shooting 1 How to shut down the device properly Ans To shut down the System properly press the Power button on the front panel for two seconds until Power LED blinks then go off 2 The PNMD can t configure My Network setting Ans O Make sure that your RJ 45 cable is connected with the device and your PC Switch O Check if the LINK ACT LED illuminates O Check the power of the device your PC and Switch Make sure that it s on O Check your PC s IP address make sure that it has a static IP or connects with a router with DHCP server For instruction about the IP setting Please refer to the IP Protocol Setup Chapter o Reboot the system with Web based UI or press the Reset Default Button to restore the factory default setting and reboot 3 The device can t find my SATA interface HD Ans O The HD is unformatted Please format it with our HD Format tool O The partition format of HD is not EXT3 ex NTFS Please format it with the provided Format tool O The HD maybe broken Please change another HD and try again 4 1 use Device as a Web FTP server but the users that outside the LAN can t access it Ans Oo For WAN users to get access to the FTP or WEB server you should link the device to a router with appropriate configuration Please make sure that 1 The NAT functionality is enabled in your router 2 Inthe port mapping session the Internal Host IP should be
43. rom connecting with the device 1 Select Denied From the IP Access Check drop list 2 Fill the IP address 192 168 1 3 in the IP Address 1 box 3 Click Apply to execute your configuration IP Filter Setting IP Filter Setting IP Access Check Denied IP Address 1 el IP Address 2 IP Address 3 IP Address 4 IP Address 5 IP Address 6 IP Address IP Address g IP Address 9 IP Address 10 ae be 44 Security MAC MAC Filter Setting The Security MAC function provides access management by MAC address filtering There are three modes for the MAC filter 1 Disable Disable the MAC Filer function All MAC addresses are allowed to access the device 2 Allowed Setup the MAC addresses that are allowed to access the device Only the configured MAC addresses have the right to access the device 3 Denied Setup the MAC addresses that are denied to access the device The MAC addresses that are configured are not allowed to access the device Tip For example to prevent the MAC address DO E0 7D CD C5 5E from connecting to the device 1 Select Denied From the MAC Access Check drop list 2 Fill the MAC address DO E0 7D CD C5 5E in the MAC Address 1 box 3 Click Apply to execute your configuration iter Seting Securty MAC MAC Filter Setting MAC Access Check Denied MAC Address 1 DOROD CDCsE MAC Address 2 MAC Address 3 MAC Address 4 MA
44. t The Web server provides an easy way to Share files by web site It also equips 2 USB ports for your USB storage devices and USB printer With connection to USB storage the device shares your files in a more flexible way The set up procedures and operation are simple and user friendly The embedded Linux device works highly stable and is affordable for continuous operation Key Features Supports CIFS SMB for Microsoft Supports user name amp password for 50 Network which allow remote users to sets retrieve files easily using My Neighborhood WEB based User Interface UI for Supports access management for 100 easy configuration folders Support one 3 5 SATA HDD up to 750G Built in Samba server Provides PNMD for user friendly setup Supports static IP amp DHCP client network environment Embeds FTP server for FTP clients to Supports Unicode for transfer files conveniently Supports USB memory stick pen drive USB Hard Disk Equips one backup button for copying files conveniently Embeds Web server for Web site construction Support firmware update over the Graphic User Interface GUI Supports 32 concurrently connected users Provides Password security for management amp HD Access multiple language characters Support eSATA interface connection Support AV server Compatible with Windows 95 98 98SE ME XP 2000 NT4 0 Linux MAC OS Supports group access management Complies w
45. talling the EZIP Backup n 16 MAKING CONNECTION WITH THE DEVICE ccccceeeees 18 Connecting the device with PNMD ccee ee 18 To access to folders In the device nn 22 MANAGEMENT GUIDE 23 STARTING THE GRAPHIC USER INTERFACE GUD 23 USING THE GRAPHIC USER INTERFACE GUD 24 U derstandino tne GUD ertene a A A mannii aca AA a 24 Management ITeMSNSE nts wiienerieeinhiiduade teens E mnintaiets 24 SND Sees erases nares A a 26 COMS ionien raae eae eater ened bende ent ay pacha eee eet ee eed pena ones 26 Orat ON sciare r e EA rE 26 DISK a EE E EAE ETEA items 27 Folder Folder Configuration ssssssrsrrsserrerrrrrrrrrrrrs 27 To Configure Folder PropertieS cccccecseeeeeeseeeeeeeaeees 27 TO AGG a New Folde nisiasatarsvicarecwne ri eina raa 31 TO Delete a Folden ecccivusrsoadadurdenade ieta EA ADES 32 Disk HD Configuration rrrriririririrrrrrrrrrn 32 NETWORK csiacenicniceacandauacxatubosuananeesneeadcentudwtancctataeinss 34 Host Host Name Setting rrn 34 IP Address IP address Setting nccc 34 To Enable DHCP CENt riseire pinar REEN 34 To Configure the IP Addresses for the DeVICE 08 8 34 UNTO MOGE si00ce 1p an bwadeyscewencnedad is wend Sateen a 35 SVEN escent erase teentearisennn an O E 36 Administrator Administrator Setting 36 Time System Time Setting 37 User User Configuration 38 TO Configure d USET wiidtinerestisrieieeiaiaiatactoiseied
46. the folder name description and user authority To Configure Folder Properties Click on the folder that you are going to configure 27 The folder configuration page shows up This page allows users to e Change Folder Name Folder Description e Add or remove authorized users or groups for this folder e Change folder accessing authority level for users and groups Folder settings amp permissions Folder name Share al Folder description Share to All Please set user s limit tor this folder Authentication free access Wo access for all users C Read only access for all users Readtyrite access for all users C Current access permission for all users Group Permissions setting No access F Group applied C Read only Read and write User Permissions setting Wo access C Read only Read and write To change the folder name folder description 1 Click on Change Folder Name or Change Description icon The Folder Name Folder Description Setting page shows up Folder name Share Folder description Share to All 28 2 Fill in the new name or new description for the folder and click Apply Note e Folder Name 0 15 characters The name for the folder e Description 0 48 characters A note for the folder e Both folder name and description are alphanumeric e Blank character is not allowed for folder name and description Folder name Old folder name ohar
47. x gt Please type your user name and password a site 10 10 7 152 Realm Network Harddisk User Name admin Password aperi Save this password in pour password list Cancel Note To get instructions using the GUI please see Using the Graphic User Interface GUI 21 To access to folders in the device Double click the EA shortcut on your desktop to start the PNMD The PNMD window pops up Select your NAS and click the _Open Share button Double click on the folder that you are going to access An authentication window pops up Fill in your username and password to access to this folder Note 1 We provide one default username password as admin admin 2 As default the Share folder is created automatically and it can be read write by all users 3 You can change the authorities of the three predefined users for getting accessed to each folder To change their authorities please see To Configure Folder Properties 4 To add or configure a account please see To Configure a User Users that would like to use another set of username password after getting accessed to any folder please log off your operation system and log on again P Network HD 192 168 1 1 TE Fie Edit view Favorites Tools Help J gt wi pa Search Kes Folders E Address W 192 168 1 1 Network Tasks G Share E web af Add a network place Su view network connections ie
Download Pdf Manuals
Related Search