Home

Electrolux 5995447108 Cooktop User Manual

image

Contents

1. Plug the three prong plug from the appliance into the properly grounded and polarized wall receptacle 18 Operation VERIFYING THE OPERATION A WARNING e If the cooktop fails to operate properly ensure that the electrical power supply and gas supply are tumed on and that all installation steos have been carefully followed Call a qualified service technician if the cooktop still does not operate properly The cooktop and shut off valve must be disconnected from the gas supply piping during any pressure testing exceeding 1 2 pound per square inch 3 5 kPA The cooktop must be isolated from the gas supply piping by closing the shut off valve during any pressure testing at or below 1 2 pound per square inch 3 5 kPA Before beginning the test procedure ensure that the gas supply is turned off at the shut off valve all cooktop control valves are in the OFF position and all burner rings burner caps and grates are properly positioned on the cooktop Rotate one knob at a time counterclockwise to the LITE HI position Verify that all ignitors spark continuously then return the knob to the OFF position Repeat for all knobs See Figure 8 Figure 8 Burner Control Valve Operation 19 Turn on the main gas supply to the cooktop by opening the gas shut off valve Test each burner separately by pressing and turning one control knob at a time counterclockwise to the LITE HI position All ignitor
2. service provided does not meet the product specifications do not proceed with the installation Call the seling dealer the gas supplier or a licensed electrical or plumbing contractor e The grounding plug must not under any circumstances be cut or removed e This appliance must be installed by a licensed plumber or gas fitter when installed within the Commonwealth of Massachusetts Gas Supply Requirements Check your local building codes for the proper method of installation In the absence of local codes this appliance should be installed in accordance with the National Fuel Gas Code ANSI Z223 1 NFPA 54 Be certain that the appliance being installed is correct for the gas service being provided Refer to the data plate located on the bottom of the cooktop chassis 12 Making the Gas Electric Connection LIQUIFIED PETROLEUM PROPANE GAS CONVERSIO This appliance can be used with Natural Gas and Propane Gas It is shipped from the factory for use with natural gas A kit for converting to LP gas is supplied with your cooktop The kit is marked FOR LP PROPANE GAS CONVERSION Follow the installation instructions which are inside the envelope The conversion must be performed by a qualified service technician in accordance with the kit instructions and all local codes and requirements Failure to follow instructions could result in serious injury or property damage The qualified agency performing this work assumes responsibili
3. 477 EN Installation Instructions Slide In Gas Cooktop Electrolux E36GC76EPS E48GC76EPS 5995447108 2 Safety IMPORTANT SAFETY INSTRUCTIONS Safety Precautions Do not attempt to install or operate your unit until you have read the safety precautions in this manual Safety items throughout this manual are labeled with a Warning or Caution based on the risk type Definitions Z This is the safety alert symbol It is used to alert you to potential personal injury hazards Obey all safety messages that follow this symbol to avoid possible injury or death A WARNING WARNING indicates a potentially hazardous situation which if not avoided could result in death or serious injury A CAUTION CAUTION indicates a potentially hazardous situation which if not avoided may result in minor or moderate injury CAUTION CAUTION used without the safety alert symbol indicates a potentially hazardous situation which if not avoided may result in property damage IMPORTANT Indicates installation operation or maintenance information which is important but not hazard related SAFETY PRECAUTIONS A WARNING Read all instructions before using the appliance Improper installation adjustment alteration service or maintenance can cause personal injury or property damage Refer to these instructions and the accompanying Use amp Care Manual For assistance or additional information consult a qualified in
4. This guide will help you anticipate all installation connections QUESTIONS For toll free telephone support in the U S and Canada 1 877 4ELECTROLUX 1 877 435 3287 For online support and Internet product information www electroluxusa com 2005 Electrolux Home Products Inc Post Office Box 212378 Augusta Georgia 30917 USA All rights reserved Printed in the USA 6 Finding Information TABLE OF CONTENTS SATAY E 2 Definitions esses 2 Irrportart Safety Iretrudions 2 Safety Precaulions sesssesssssssssssssesesssessesseessessees 3 Finding Information s 5 Please ReadAnd Save This Guide m QUES 2 5 Table OFCONteNS 6 Preparing for Installation 7 Verifying Package lt 7 Cabinet Courterop Preparation 7 Making the Gas Electric Connection Il Reruirerrerts sese Il LP Gas Conversion 12 InStal 14 Installing the Cooktop sss 14 Cornectingthe Gas essen 14 Gas andElechic Requirements Table 15 Installingthe Burner Corrponerts 16 Meking the Electrical Connedion 17 Operation un 18 Preparing for Installation 7 VERIFY PACKAGE CONTENTS m A m L m L m E m Literature Pack G
5. electrical supply may be easily disconnected in the event that service becomes necessary Also provide extra slack in the cable to allow the cooktop to be removed for servicing IMPORTANT e f the electrical supply circuit does not have a grounding type receptacle it is the responsibility of the customer to have the existing receptacle changed by an electrician to a properly grounded receptacle The power supply must be properly polarized Reverse polarity will result in continuous sparking of the electrodes even after flame ignition If the power supply is not properly polarized it is the responsibility of the customer to have the polarity corrected e f there is any doubt as to whether the wall receptacle is properly grounded or polarized have it checked by a qualified electrician prior to installing the cooktop Do not plug the cooktop into Ground Fault Circuit Interrupter GFCI receptacles The cooktop spark ignition module can cause a GFCI to trip NOTE It is the owner s responsibility to ensure that the electrical connection for this appliance is performed by a qualified technician The electrical installation including minimum supply wire size and grounding must be in accordance with National Electric Code ANSI NFPA 70 1993 or the latest revision and local codes and ordinances 14 Installation INSTALLING THE COOKTOP Place and center the cooktop within the cutout Secure the cooktop to the countertop utilizing t
6. he two 2 1 4 20 bolts provided Do not overtighten the screws IMPORTANT Do not use a hardening compound or caulking to permanently seal the cooktop into place as the unit must be readily removable for service If such a hardening compound is used removal of the unit will be at the customers expense CONNECTING THE GAS A WARNING The maximum gas supply pressure to the regulator must not exceed 1 2 pound per square inch Verify that the proper gas supply has been provided Do not apply excessive pressure when tightening connections and fittings Do not use plurrber s putty or Teflon tape on gas corrpression connections It can defeat the proper sealing of these fittings Use plurrber s putty or Teflon tape only on pipe thread fittings Tum all cooktop control valves to the OFF position then tum on the gas supply Check all supply lines and connections for leaks using a soap and water solution Do not use a flarre to check for leaks After verifying that there are no gas leaks turn off the gas supply to the cooktop by tuming the gas shut off valve to the off position Leak testing of the appliance shall be conducted according to the manufacturer s instructions e For LP gas installations the LP gas tank must have its own high pressure regulator This is in addition to the pressure regulator supplied with the cooktop Attach the gas pressure regulator included with the cooktop to cooktop pipe nipple inlet Insta
7. heir shipping packages Place each burner ring onto its corresponding burner base being certain that the four alignment tabs slide into the matching notches in the base Set each porcelain burner cap on top of its corresponding burner ring Place each grate onto the cooktop being certain that the rubber feet are positioned in the locating dimples Figure 7 Burner Cap Burner Ring Top Frame eS ZZ Burn er Head Fixed Installation 17 MAKING THE ELECTRICAL CONNECTION A WARNING e Ensure that the power supply is disconnected before proceeding Verify that the power supply matches the ratings found on the appliance data plate before proceeding The complete appliance must be properly grounded at all times when electrical power is applied e Do not ground the appliance with the neutral white house supply wire A Separate ground wire must be utilized e f aluminum house supply wring is utilized splice the appliance copper wires to the aluminum house wiring using special connectors designed and agency certified for joining copper and aluminum e Follow the connector manufacturer s recommended procedure carefully Improper connection can result in a fire hazard Do not atterpt to use this appliance in the event of a power failure Do not use an extension cord with this appliance Do not install a fuse in the neutral or ground circuit Do not ground this appliance to a gas supply pipe or hot water pipe
8. hould not be heated on this cooktop 4 Safety A WARNING Based on safety considerations the top bumer flame should be adjusted so it does not extend beyond the edge of the cooking utensil e information in this manual is not followed exactly a fire or explosion may result causing property damage personal injury or death What to do if you smell gas Dont try to light any appliance Do not touch any electrical switch do not use any phone in your building nmrrediately call the gas supplier from a neighbor s phone Follow the gas supplier s instructions f you cannot reach your gas supplier call thefire department e For your Safety Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance e Installation of this appliance must be performed by a qualified installer service agency or the gas supplier Contact the nearest Electrolux Authorized Servicer call 1 877 435 3287 or contact us on the intemet at www electroluxusa com Finding Information 5 READ AND SAVE THESE INSTRUCTIONS NOTE Installer Leave instructions with owner Owner Read your cooktop Use amp Care Manual It contains important safety information for operating this appliance It also has many suggestions for getting the best results from your cooktop Read all instructions before installing the cooktop For your safety please read and observe all safety instructions
9. ions are provided Figure 1 E36GC76EPS 36 914mm Minimum Dimensions apply to both FT E48GC76EPS 48 1218mm Minimum gt models unless otherwise stated see Figure 1 Locate the electrical supply box within reach of the included 48 inch long flexible cord so the connection is accessible e when the cooktop is in place combustible side 1 1 2 38mm wall both sides Typical Countertop Cooktop opening E E36GC76EPS 36 914mm 7 3 4 E48GC76EPS 48 1219mm 197mm 36 914mm Utilities Location pes 28 1 4 717mm 10 254mm E36GC76EPS 152 24 610mm c E48GC76EPS 30 762mm 18 457mm 30 762mm 10 254mm Minimum I Min to 5 8 16mm Overhang both sides Preparing for Installation 9 Provide an opening in the countertop as shown see Figures 2 3 4 5 Nor combustbls and 6 Position the cutout so that 7 minimum clearances are met TEN locations _ Drill two 1 2 13mm holes through support shelf for cooktop mounting bolts E36GC76EPS 16 5 8 422mm E48GC76EPS Fr Figure 2 10 Preparing for Installation If 2 7 clearance c v 30 min for unprotected cabinet 18 in 10 min to nearest combustible wall either side of unit Making the Gas Electric Connection 11 REQUIREMENTS WARNING e f the gas or electric
10. ll a gas shut off valve not included with the cooktop in the main gas supply line in an accessible location near the cooktop Complete connection of the gas supply to the cooktop by installing 1 2 inch flexible gas line not included with the cooktop between the pressure regulator and the shut off valve IMPORTANT To prevent damage to the gas pressure regulator install the regulator only after the cooktop is mounted in its permanent position Ensure that the arrow on the regulator points in the direction of the gas flow towards the cooktop Installation 15 GAS AND ELECTRIC REQUIREMENTS TABL The required voltage frequency and amperage ratings are listed on the product data plate outside on the cooktop bottom The gas and electric requirements are also shown in the table below Model No Electrical Total Gas type Manifold Minimum gas circuit connected pressure supply required load pressure 4 Water Column 5 Water Column E36GC76EPS 120VAC 0 7 Amps Liquid Propane 10 Water Column 11 Water Column 60Hz 15A 0 084 Kw Natural 4 Water Column 5 Water Column E48GC76EPS Liquid Propane 10 Water Column 11 Water Column 16 Installation INSTALLING THE BURNER COMPONENTS A WARNING Never atterrpt to operate the cooktop with any of the bumer rings bumer caps or bumer grate components removed Burner Components Remove the brass burner rings porcelain burner caps and porcelain grates from t
11. riddle Bolts Washers Simmer Plate Burner Grate Pack Wok Stand Burner Set Stainless Steel Cleaner Gas Pressure Regulator LP Conversion Kit Burner Cap Pack ABINET COUNTERTOP PREPARATIO The installation of this built in appliance must be completed by a qualified appliance technician or contractor Proper installation is the owner s responsibility Carefully check the location where the cooktop is to be installed The cooktop should be placed for convenient access but away from drafts that may be caused by open doors and windows or by HVAC duct outlets Make certain that gas and electrical power can be provided in the selected locations Plan the installation so that all minimum clearances are met or exceeded Dimensions shown provide minimum clearances unless otherwise noted A WARNING To reduce the risk of personal injury caused by reaching over a hot appliance cabinet storage space located directly above the cooktop should be avoided e Keep appliance area clear and free from combustible materials gasoline and other flammable vapors and liquids Failure to provide proper clearances may result in a fire hazard Do nct store combustible materials or items adversely affected by heat immediately above or below the cooktop The back edge of the cooktop must remain a minimum of 2 1 2 64mm from any combustible backsplash material This will require special cabinet and countertop dimensions Installations
12. s will spark simultaneously It will take approximately four seconds for ignition to occur at which time all igniters will stop sparking If ignition does not occur within four seconds turn off the knob wait for at least five 5 minutes to allow any gas to dissipate then repeat this ignition test The control knob can then be rotated counterclockwise from HI to LOW to adjust the flame height progressively Repeat the ignition test for all burners When installed properly the flame will be steady and quiet It will also have a sharp blue inner cone that will vary in length proportional to the burner size Flame adjustment will not be necessary Read and understand the accompanying Use amp Care Manual prior to cooking with this appliance The Use amp Care Manual contains additional important safety service and warranty information Electrolux www electroluxusa com 1 877 4Electrolux www electroluxca com
13. staller service agency manufacturer dealer or the gas supplier For your safety Do not obstruct the flow of combustion and ventilation air to the unit Keep appliance area clear and free from combustible material gasoline and other flammable vapors and liquids Do not use or attempt to use this appliance in the event of a power failure This unit is designed as a cooking appliance Never use it for warrring or heating a room This appliance must be installed with the gas pressure regulator supplied with it Disconnect the electrical supply before installing or servicing the appliance This appliance must be grounded Connect only to a properly grounded electrical supply Refer to Electrical Requirements Install or locate this appliance only in accordance with these installation instructions Use this appliance only for its intended use as described in this manual Do not use corrosive cherricals or vapors in this appliance This type of appliance is not designed for industrial or laboratory use As with any appliance close supervision is necessary when used by children Do not operate this appliance if it has a darraged electrical cord plug conduit or Wires if it is not working properly or if it has been damaged or dropped This appliance should be installed and serviced only by qualified service personnel Sorre products such as whole eggs and sealed containers such as closed glass jars may explode and s
14. ty for the conversion A WARNING Severe shock or damage to the cooktop may occur if the cooktop is not installed by a qualified installer or electrician CAUTION Any additions changes or conversions required in order for this appliance to satisfactorily meet the application needs must be made by a qualified service technician in accordance with the manufacturer s instructions and all codes and requirements of the authority having jurisdiction Failure to follow the instructions could result in serious injury or property damage The qualified agency perforrring this work assumes responsibility for the conversion Making the Gas Electric Connection 13 Electrical Supply Reguirements The correct voltage freguency and amperage must be supplied to the appliance from an isolated grounded circuit which is protected by a properly sized circuit breaker or time delay fuse The cooktop must be connected to the power supply with copper wire only The use of aluminum wire may result in unsatisfactory connections Flexible armored or nonmetallic sheathed copper cable with a grounding wire should be used to supply electrical power to the junction box or receptacle The cooktop s factory equipped three prong grounding plug must be inserted into a mating grounding type receptacle in accordance with National Electric Code and applicable state municipal and local codes Be certain to locate the junction box or electrical outlet so the
15. with less than 2 1 2 fromthe rear of the cooktop to a corrbustible backsplash must use Electrolux Backsplash models ACCBGO096S11 for E36GC76EPS or ACCBG0948S1 for E48GC76EPS 8 Preparing for Installation IMEORTANT When installing the cooktop into a laminated Formica etc or synthetic Corian etc countertop radius the comers of the cutout to prevent cracking of the countertop e Follow the countertop manufacturer s instructions regarding the minimum comer radius use of heat reflective tape reinforcement of comers etc f cabinet storage space is to be provided directly above the cooktop the risk of personal injury may be reduced by installing a ventilating hood that projects horizontally a minimum of 5 inches beyond the face of the cabinets Both models are designed to allow installation in standard 24 inch deep base cabinets with 25 inch overall depth countertops Deeper cabinets and countertops may be used to provide required clearances to combustible rear wall materials or for design purposes The specified cabinet dimensions must be provided The cabinet and or countertop must completely enclose the recessed portion of the countertop All contact surfaces between the appliance and the countertop must be solid and level Plan the installation so that the electrical connection gas shut off valve and pressure regulator are accessible from the front of the cabinet and so that all of the minimum required dimens

Download Pdf Manuals

image

Related Search

Related Contents

  Online User`s Guide for Linux    X 502  AVTECH DR083 digital video recorder  manuale posa slim4 fra  HDMI Wireless Extender Installation Guide  Philips Satinelle Epilator HP6502/00  RCA M1 User's Manual  Méthodologie transdisciplinaire de gestion de corpus pour  

Copyright © All rights reserved.
Failed to retrieve file