Directed Electronics HVM702A Car Video System User Manual
Contents
1. Mark 1 1 2 from the inside of the headrest housing and cut the material away 5 Optional Step Glue the material to the inside of the headrest housing Take care not to use exces sive glue so that the headrest bezel is not glued to the headrest housing NOTE Glue is not required if the material of the headrest covering is of sufficient thickness to be tensioned by the headrest bezel 6 Insert the headrest bezel into the headrest housing and secure the assembly using the provid ed hardware NOTE Ensure that the UP arrow on the headrest bezel is pointing up 11 Headrest Installation 00906090090099090009099099909090090099909900000999909000909099090000099099990000909909909090999909990099999 5 pin adapter 12 8 pin main DIN cable 1 Unplug the DIN cable from the monitor 2 Connect the LCD screen s 8 pin DIN plug into the 8 pin DIN plug of the headrest NOTE When assembling the cable match the arrows at each end of the connector NOTE Feed and orient the connector assembly behind the shroud mount in the lower right hand corner You may have to feed some of the DIN cable up into the headrest to accomplish this positioning 3 Position the monitor over the mounting shroud and apply even pressure to each corner of the mon itor until the internal clips lock the monitor in place NOTE Do not press on the LCD screen as this will dam age the screen 4 Tape the end of the DIN plug2. CH and the other to B CH A CH is 2 3MHz left and 2 8MHz right B CH is 3 2MHz left and 3 8MHz right Ensure that the headphones being used are of different receive frequencies or are capable of 2 channel reception NOTE In the Mode selection use the A V buttons to select the desired setting and press SEL to set the selected video mode DISP 10 FULL A 4 3 picture is enlarged in the horizontal direction only enabling viewing of a 4 31 the picture 4 3 Standard picture mode WIDE A 4 3 picture is enlarged in the same pro portion both vertically and horizontally This setting is ideal for cinema sized pictures wide screen PAL NT PAL NT video format PAL or NTSC UP DN UP DN picture is inverted LET RIT LET RIT picture is mirrored imaged left right swapped 2004 Directed Electronics Inc ceccocococooosoocoooooooo 2004 Directed Electronics Inc RR TS RS SS SR SS SS ese see 1 Remove the cover from the headrest 2 Using the headrest housing as a template posi tion the housing over the backside of the headrest and mark the foam with a felt tip pen Cut the marked portion of foam and pull out the cut por tion 3 Insert the headrest housing into the headrest and secure the the headrest Usually wire ties attached to the headrest posts is sufficient NOTE Ensure that the UP arrow on the headrest housing is pointing up 4 Replace the cover over the headrest
3. be repaired or replaced with a new or comparable reconditioned part s at Directed s election To obtain warra ty service the Product must be returned to a Directed authorized dealer along with proof of purchase and proof of installation by an Authorized Directed Dealer This warranty is non transferable and does not apply to any Product that has been modified or used in a manner contrary to its intended purpose and does not cover damage to the Product caused by installation or removal of the Product This war ED is VOID if the product has been damaged by accident or unreasonable use negligence acts of God neglect improper service or other causes not arising Qut of defect in materials or construction This warranty does not cover the elimination of externally generated static or noise or the correction of antenna problems or weak television reception damage to tapes video games software camcorders discs speakers accessories or vehicle electrical systems cosmetic damage or dam age due to negligence misuse abuse failure to follow operating instructions acci dental spills or customer applied cleaners damage due to environmental causes such as floods airborne fallout chemicals salt hail windstorms lightning or extreme temperatures damage due to accidents road hazards fire theft loss or vandalism damage due to improper connection to equipment of another manufac turer modification of existing equipment use of a faulty tap
4. set to low If in A V mode check audio connec tions Remote control does not work Avoid using the product under strong amp direct sunlight Replace the battery in the remote control Intermittent audio Power supply voltage is too low TV picture appear to shakes while driving Bad reception Check antenna and try reception in a better area No audio from headphone Ensure the Power is switched on at the headphone Replace the batteries in the headphone Check to ensure the frequency of the headphone is the same as set up in the monitor Check the volume level setting on the headphone 2004 Directed Electronics Inc Power 12VDC 9 16VDC Power consumption 750mA Maximum 12VDC Power consumption stand by 50mA Video type PAL NTSC Video input level IR frequency left right 1Vp p 75 ohm composite A ch 2 3 MHz 2 8MHz B ch 3 2 MHz 3 8MHz IR range 1m 30 1m 15 Headphone stereo output 0 5 watts 16 ohms channel Actual screen size 155 W X 880 H mm Dimensions Weight 189 4 W X 126 5 H X 35 D mm 536 3 grams Remote control battery lithium battery CR2025 3V NOTE Specifications are subject to change without notice 2004 Directed Electronics Inc 17 18 2004 Directed Electronics Inc 9 2004 Directed Electronics Inc The company b
5. to prevent dam age to the pins Then feed this cable from the hol low post of the headrest down through the seat back and connect it to the cable from the DVD play er NOTE Ensure the cable does not entangle or interfere with the seat positioning adjusting mechanism 2004 Directed Electronics Inc 5 To remove the monitor from the mounting shroud for service or repair insert and slide a plas tic card at the edge of the monitor This vvill remove the clip engagement of the monitor Slightly lift this side of the monitor out then repeat this pro cedure on the other side of the monitor IR Wireless stereo headphone optional Video i YELLOW Audio L WHITE GND 2004 Directed Electronics Inc 13 Refer to diagram on the next page for the discussion that follows CONNECTING A MONITOR TO MULTIPLE SOURCES When the monitor s power is turned on the input source will appear in the upper right hand corner AV1 AV2 etc Press the SOURCE button on the remote to switch between the available sources for that monitor NOTE If PARKING is displayed on the screen it means that this monitor s will not display video until the parking brake is set vehicle parked NOTE You cannot change sources on video output 3 using the source selector Only the remote will switch 3 output between the 3 video inputs For operating convienence when the system is connected to several other devices whic
6. Automate Matas VIDEO INSTALLATION GUIDE 7 Widescreen TFT LCD Color Monitor Owners Installation Manual MODEL HVM702A 2004 Directed Electronics Inc N81702A 12 04 NON TRANSFERABLE LIMITED CONSUMER VVARRANTY Directed Electronics Inc Directed promises to the original purchaser that the automotive video monitor and or source unit s the Product excluding acces sories purchased and installed from a Directed authorized dealer within ninety Lo days after purchase of the new vehicle in which the Product is installed will be free from defects in materials or workmanship under normal use and conditions for a period of three 3 years from date of purchase or the first 36 000 miles as reg istered on the new vehicle s odometer reading at time of delivery of the Product for warranty service whichever occurs first Product purchased or installed more than ninety 90 days after the new vehicle is purchased are warranted for a period of one 1 year from date of purchase of the Product Directed promises to the original purchaser that all video accessories will be free from defects in materials and workmanship under normal use and condition for a period of ninety 90 days after the date of purchase A sales receipt and or war ranty registration card is required to provide proof of date of purchase of the Product or accessories Should the Product prove to be defective during the applicable warranty period the Product will
7. ING stickers on the unit Do not use any chemical solvent cleaning agent or corrosive detergent to clean away dirt on the surface of the screen Doing so may cause irreversible dam age to the surface of the LCD screen To clean off dirt or fingerprints it is rec ommended that a soft damp lens cleaning cloth be used Using spare parts from another manufacturer may cause permanent damage to the unit Avoid installing the monitor screen in a position that is exposed to direct sun light and hot air vents Install the unit in a dry location avoid condensation Ensure that all wiring is properly connected before operating the unit Should the LCD panel break avoid contact with the broken glass or fluid leaking out from the enclosure If you come into contact flush and clean the affected areas with plenty of water Seek medical attention immediately When operating the monitor avoid touching or pressing on the LCD screen Excessive force will damage the LCD screen When installing this unit in a vehicle ensure that the installation and use of this unit is in compliance with local vehicle rules and regulations Before replacing a blown fuse turn the unit off and disconnect all power Ensure the replacement fuse is of the same rating 5A of the fuse being replaced If during operation the unit overheats or malfunctions turn off the power and contact your dealer Do NOT disassemble the unit there are no user servicea b
8. e SEL button now selects a menu item to be adjusted MENU ADJUSTMENTS 1 Press the MENU button on the remote to display the following four groups VIDEO AUDIO MODE DISP Bright Volume Full PAL NT Color Bass 4 3 UP DN Tint Mute Wide LET RIT Dimmer H P Reset 2 Use the A V buttons on the remote to highlight the VIDEO AUDIO MODE or DISP groups 3 Press the SEL button to select the desired group Use the A V buttons to select the desired setting to change 4 Use the buttons to change the setting 4 If no entry or action is taken within approximately 8 seconds the Menu will disappear and any changes are saved Pressing the MENU button will also exit the adjustments screen VIDEO BRIGHT ness 0 15 COLOR 0 15 TINT 0 15 DIMMER ON OFF In the ON position the LCD screen is dimmed which offers better veiwing at night or in dimly lighted envirorments RESET YES NO This resets the unit back to the factory default settings for the above adjustments 2004 Directed Electronics Inc 9 AUDIO MODE VOLUME 0 15 BASS ON OFF MUTE ON OFF H P A CH B CH This setting allows the use of 2 headphones on different frequencies If two video units are installed and for example each unit is playing a different video using two headphones set at the same frequency may result in interference of the audio signal between the two headphones One of the video units should be set to A
9. e cartridge or clean ing of the VCR head or Product which has been opened or tampered with for any reason or which has been damaged due to alteration or service performed by any one other than Directed Electronics Inc ALL WARRANTIES INCLUDING BUT NOT LIMITED TO EXPRESS WARRANTY IMPLIED WARRANTY WARRANTY OF MERCHANTABILITY FITNESS FOR PARTICULAR PURPOSE AND WARRANTY OF NON INFRINGEMENT OF INTELLECTUAL PROPERTY ARE EXPRESS LY EXCLUDED TO THE MAXIMUM EXTENT ALLOWED BY LAW AND DIRECTED NEITHER ASSUMES NOR AUTHORIZES ANY PERSON TO ASSUME FOR IT ANY LIABILITY IN CON NECTION WITH THE SALE OF THE PRODUCT DIRECTED HAS ABSOLUTELY NO LIABIL ITY FOR ANY AND ALL ACTS OF THIRD PARTIES INCLUDING ITS LICENSED DEALERS OR INSTALLERS IN NO EVENT WILL DIRECTED ELECTRONICS INC BE LIABLE FOR ANY INCIDENTAL SPECIAL OR CONSEQUENTIAL DAMAGES nd DING LOSS OF PROFITS BY PURCHASING THIS PRODUCT THE CONSUMER AGREES AND CONSENTS THAT ALL DISPUTES BETWEEN THE CONSUMER AND DIRECTED SHALL BE RESOLVED IN ACCOR DANCE WITH CALIFORNIA LAWS IN SAN DIEGO COUNTY CALIFORNIA Some states do not allow limitation on how long an implied warranty lasts In such states the limitations or exclusions of this Limited Warranty may not apply Some states do not allow the exclusion or limitation of incidental or consequential dam ages In such states the exclusion or limitation of this Limited Warranty may not apply to you This Limited Warranty aves you specific legal rights a
10. ehind this system is Directed Electronics Inc Since its inception Directed has had one purpose to provide consumers vvith the finest vehicle security car stereo products rear seat entertainment and accessories available The recipient of more than 20 patents in the field of advanced electronic technology Directed is ISO 9001 registered Quality Directed Electronics products are sold and serviced throughout North America and around the world Call 800 274 0200 for more information about our products and services DEI is an ISO 9001 registered company Directed is committed to delivering world class quality products and services that excite and delight our customers D sat ELECTRONICS INC Directed Electronics Inc Vista CA 92081 www directed com 2004 Directed Electronics Inc All rights reserved N81702A 12 04
11. h have their own remotes you can use those remotes through the HVM702a to operate the other devices This is done by connecting the Remote Eye IR interface cable from the other devices to the R emote Sensor Input at the VS102 video selector 14 2004 Directed Electronics Inc AN Source AN Source AN Source VCR DVD Player Navigation O n q mum Remote Eye AN Remote Eye AN Remote Eye i AN AL TT jut No Color Description 1INC zinc 3 NC 4 BLACK System GND 5 RED ACC 6 BLUE EmerBrake input 7 NC ER nn A 8 sen B 12v constant s uet wm amet Power Cable I sweourmvseiccron VS102 3 Monitor 3 Monitor D Monitor WHITE Audio umm e Tu ML DE WHITE Audio L ET i YELLOW Vidi ea YELLOW Video e mr mv Video Mini Plug to RCA Optional 2004 Directed Electronics Inc 3 RCA to 3 RCA Optional 15 Use the following chart to assist in troubleshooting the system 16 PROBLEM SOLUTION Power will not turn on No picture or sound Check connections to the power supply and other devices Check connections of external device Have picture but no sound Check if the volume is
12. irected Electronics please visit Automate at www automatecarsecurity com Features 000000000000000000000000000000000000000000000000000000000000000000000000000000000000 e High definition low reflection TFT LCD screen 1440 W X 234 H 16 9 wide screen ratio full 4 3 or wide selectable All functions can be operated from the remote control power volume source select etc Picture noise eliminated by implementation of Blue screen OSD On Screen Display of all functions Brightness color and tint controls provided Invert image control Up Down Left Right One touch dimmer control Low power consumption 750 mA at 12VDC Input voltage tolerance 9VDC 16VDC External A V input 2 ch IR wireless transmitter Front headphone stereo output PAL NTSC manual select 2004 Directed Electronics Inc 5 What is Included m 7 TFT LCD Color Monitor mM Mounting hardware package mM Headrest housing E EV sponge M Headrest bezel E DIN to RCA cable for A V input mM Remote Control Unit battery System Description MONITOR REMOTE CONTROL 19 si 8 C Oy i7 10080 O Ol 16 10115 1218 COR 14 13 1 2 3 4 5 6 MONITOR Headphone jack Volume up down buttons Wireless headphone IR transmitter Menu changes the viewing aspect ratio Full 4 3 or Wide Power On Off button Remote control IR sensor receiver 7 DIN jac
13. k for external audio video input Ou amp rn E REMOTE CONTROL 8 Power On Off button 9 SEL MUTE button selects item on menu and serves as the mute On Off but ton 6 2004 Directed Electronics Inc 10 Volume control if the OSD is active these allow scrolling through menu options 11 Menu On Off press the menu button to go back to the previous selection 12 Scan used in conjunction with a TV tuner 13 A M used in conjunction with a TV tuner 14 TX not used 15 DIM dims the LCD screen 16 Up down button for menu 17 MODE changes the viewing aspect ratio Full 4 3 or Wide 18 SOURCE used in conjunction with a TV tuner 19 Remote IR LED IR LED used to transmit commands to the monitor Remote Control 1 A W use these buttons to adjust the selected setting on the MENU screen 2 SOURCE press this button to select the video source AV1 AV2 3 MENU press this button to display the MENU screen Continue to press this button additional times to scroll through the MENU selections 4 POWER press this button to turn power on or off to the unit 2004 Directed Electronics Inc 7 eccccccccccoc ooecceeecctesscess s000000000909090000000909099990000909909909090990990990900099099 1 Follow the instructions given in the illustration below to open the battery holder 2 Remove the old battery and replace it with a CR2025 or equivalent The posi tive side of the battery must be faci
14. le parts in the unit Ensure that no foreign objects are in the unit when the LCD screen is closed The battery CR2025 in the remote control has a useful lifetime of approxi mately 6 months To ensure proper and reliable operation replace the battery in a timely manner When the unit is used in conjunction with a radio TV tuner reception quality will vary depending on the geographic location and weather conditions The rated operating temperature range of the unit is 32 92 F Cool or warm the vehicle to within this temperature range prior to unit operation The picture viewing quality of this LCD is dependent on the installed location Adjust the brightness control and or the angle of the screen to achieve the optimum visual quality 2004 Directed Electronics Inc Introduction Congratulations on your purchase of the world s finest video entertainment system At Directed we are committed to bringing you the most technologically advanced products available We are pleased that you chose a Automate Video product Through years of critical testing and hand craftsmanship we have created a wide range of video entertainment products for your viewing pleasure This system incorporates the use of on screen display menu controls that allows you to configure the system to suit your own personal preferences For your listening flex ibility audio can be heard by optional infrared wireless headphones To view other great products from D
15. nd you may have other rights which vary from state to state 920 0002 Directed Video 3 year Warranty Rev 11 04 Directed Video 3 year Automate RSE warranty 11 17 04 doc 2 2004 Directed Electronics Inc Table of Contents Non Transferable Limited Consumer Warranty 2 Important Notes 1e e EES ex e ERU ea 4 Introduction sn ants cote ore evt SS E e ree as oO 5 Features ss cepe doses aste Ge cn omae o E pala cuo 5 Whats Included sario enr eR RPM ERES sopes 6 System Description 6 Remote Control o dte ies ahs vii idea ii 7 Battery Replacement 8 Operation sgradito DOS PG DT qu E Dao e de o 8 origi MER 8 c 8 Menu Adjustments ss 9 Headrest Housing Bezel Installation 11 Headrest Installation 12 Typical Wiring Diagram 13 Multiple A V Input Selector 14 Connecting a monitor to multiple sources 14 Troubleshooting Bit A Le LL ME EE 16 Specilicationls a c Swe na 17 Notes es oie eo A d uin Rar ag Genta einen gine co a 19 2004 Directed Electronics Inc 3 BR WDM E 10 11 12 13 14 15 16 17 18 Before operating your LCD Monitor system please read these instructions carefully Retain this manual for future reference Do not remove any WARN
16. ng upward in the clip 3 Push the battery holder into the body of the remote control until the battery holder is locked 4 Properly dispose of the old battery BACK SIDE YO O 1 Insert the tip of the pen into the slot of battery case amp pull down towards a arrow mark 2 Place the battery facing up Product No CR2025 3V 3 Push battery case into remote control eccdoccc000000009090900090090990009090999909900099090909000000999909900009090909909009990990900099999 POWER ON OFF 1 Press any button on the LCD screen or press the POWER button on the remote control to turn the monitor on 2 To turn power off to the LCD screen press and hold the power button PWR on the LCD screen for 2 seconds or press the POWER button on the remote con trol NOTE When using this monitor with a multiple A V input selector AV102 with power on momentarity press the power button on the LCD screen to select AV1 or AV2 signal source MUTE Press the power on off button on the monitor to mute the audio press again to restore the audio NOTE The power on off button on the monitor does not mute the audio when there is an A V input selector VS102 in which case the button selects the A V input 8 2004 Directed Electronics Inc Press the SEL button on the remote control to the mute the audio press again to restore audio NOTE If the MENU button on the remote has been pressed prior to pressing the SEL button th
Download Pdf Manuals
Related Search