Dialogic DM/IP481-2T1-PCI-100BT Network Card User Manual
Contents
1. ideas described in this document in marketing collateral produced by or on web pages maintained by Dialogic may infringe one or more patents or other intellectual property rights owned by third parties Dialogic does not provide any intellectual property licenses with the sale of Dialogic products other than a license to use such product in accordance with intellectual property owned or validly licensed by Dialogic and no such licenses are provided except pursuant to a signed agreement with Dialogic More detailed information about such intellectual property is available from Dialogic s legal department at 9800 Cavendish Blvd 5 Floor Montreal Quebec Canada H4M 2V9 Dialogic encourages all users of its products to procure all necessary intellectual property licenses required to implement any concepts or applications and does not condone or encourage any intellectual property infringement and disclaims any responsibility related thereto These intellectual property licenses may differ from country to country and it is the responsibility of those who develop the concepts or applications to be aware of and comply with different national license requirements Dialogic Diva Eicon Eicon Networks Eiconcard Dialogic Pro and SIPcontrol among others are either registered trademarks or trademarks of Dialogic Dialogic s trademarks may be used publicly only with permission from Dialogic Such permission may only be granted by Dialogic s legal de2. Dialogic DM IP Boards Quick Install Card for PCI 100 Base T E DMP481 271 PC 1008T DMIP6OL 2E1 PC 1008T Part number 64 003 1 02 Copyright 2001 2007 Dialogic Corporation All Rights Reserved Dialegic Before You Begin Protecting the Board from Damage A Caution All computer boards are sensitive to electrostatic discharge ESD Handle all static sensitive boards and components at a static safe work area and observe anti static precautions at all times If you are not familiar with ESD safety precautions visit http www dialogic com support hwinstall to learn more Unpacking the Board Unpack the Dialogic DM IP Board board according to the following steps 1 Prepare a static safeguarded work area 2 Carefully remove the board from the shipping carton and anti static packaging Handle the board by the edges and avoid touching the board s components 3 Lay the board on the static dissipative work surface Note Place boards in static shielding bags when carrying boards from station to station CAUTION Do not remove the board from the anti static packaging until you are ready to install it Observe proper anti static precautions at all times Configuring the Hardware Board Identification The DM3 device driver part of the system software assigns board instance numbers in ascending order beginning with 0 as it detects each board in your system A board instance number is the boa
3. Dialogic products please refer to the following website to locate the appropriate supplier http www dialogic com purchase htm All contents of this document are furnished for informational use only and are subject to change without notice and do not represent a commitment on the part of Dialogic Corporation or its subsidiaries Dialogic Reasonable effort is made to ensure the accuracy of the information contained in the document However Dialogic does not warrant the accuracy of this information and cannot accept responsibility for errors inaccuracies or omissions that may be contained in this document INFORMATION IN THIS DOCUMENT IS PROVIDED IN CONNECTION WITH DIALOGIC PRODUCTS NO LICENSE EXPRESS OR IMPLIED BY ESTOPPEL OR OTHERWISE TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT EXCEPT AS PROVIDED IN A SIGNED AGREEMENT BETWEEN YOU AND DIALOGIC DIALOGIC ASSUMES NO LIABILITY WHATSOEVER AND DIALOGIC DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO SALE AND OR USE OF DIALOGIC PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE MERCHANTABILITY OR INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHT OF A THIRD PARTY Dialogic products are not intended for use in medical life saving life sustaining critical control or safety systems or in nuclear facility applications It is possible that the use or implementation of any one of the concepts applications or
4. The system software does not recognize or use the setting number of the rotary switch SW1 to determine the board ID number However you must set SW1 to a unique number for each DM3 board in your system so that the power on self test for the board s can complete successfully Use a non magnetic screwdriver to turn SW1 to one of the 15 board ID settings 1 9 and A F See the DCM On Line Help for more details on board identification Installing the Hardware NOTE If you are running in a Windows NT environment install the software install the board s and then run the Dialogic Configuration Manager DCM to configure the system 1 With your computer on the static safe work area switch off the power and disconnect all power cords from the electrical outlets Remove the cover select an empty expansion bus slot and remove the slot s retaining screw and access cover plate Use the slot s board guides as you insert the board edge connector into the slot Press firmly until the board is securely seated in the slot If you are not installing your board in an ISA form factor PCI slot remove the ISA edge retainer Replace and tighten the retaining screw to secure the board Select a new slot and repeat steps 3 and 4 for each board you are installing Use the CT Bus cable to connect the board you are installing to other boards in the system NOTE Your system may include both CT Bus boards and SCbus boards
5. To connect both board types you must install a CT Bus SCbus Adapter on one of the CT Bus boards in a system See the CT Bus SCbus Adapter Quick Install Card for installation details for the Adapter and the bus cables 7 Replace the computer cover when finished and reconnect the power cords CAUTION If your BIOS is set up to use Plug and Play functionality and there are non DM3 ISA cards in the system a conflict can be created because the DM3 card could use the same IRQs that are assigned to an ISA card This could cause the machine to stop responding You can remove the conflict by determining which IRQs are used by the non DM3 ISA cards in the system and reserving them in the BIOS for ISA use only Connecting to the RJ 48C Jack RCV_RING RCV_TIP Chassis Ground XMIT_RING XMIT_TIP Chassis Ground Chassis Ground Chassis Ground Pin 1 RJ 48C Cable Connector RJ 48C Jack After Installing the Hardware After installing the hardware run the Dialogic Configuration Manager DCM as described in the installation instructions included with the Dialogic System Software to configure your system For technical specifications and product information go to http www dialogic com products htm Warranty and Return Information Warranty Period For specific warranty information for this board refer to the Warranty section of the Products page located at this URL http www dialogic com w
6. arranties Contacting Technical Support Dialogic provides technical support for its products through a network of value added distributors who are trained to answer technical questions on installing and ee configuring Dialogic products If you are unsure how to contact your support channel please call Dialogic in the United States at 973 967 6600 9am 5pm EST and we will assist in obtaining the appropriate support channel Outside the United States please refer to http www dialogic com support contact to obtain local contact information Dialogic also provides direct support via Dialogic Pro Services agreements For more details of direct support from Dialogic please refer to http www dialogic com support DialogicPro Returning a Product To return a board for warranty repair or any other returns please refer to the following http www dialogic com support hwfaults To return a board for warranty repair please refer to the following http www dialogic com support hwfaults For all other returns contact your vendor or Dialogic Customer Support for more information see http www dialogic com support contact Sales Assistance If you have a sales question please contact your local Sales Representative or the Regional Sales Office for your area Address telephone and fax numbers are available at the Dialogic website located at http www dialogic com contact htm To purchase
7. partment at 9800 Cavendish Blvd 5th Floor Montreal Quebec Canada H4M 2V9 Any authorized use of Dialogic s trademarks will be subject to full respect of the trademark guidelines published by Dialogic from time to time and any use of Dialogic s trademarks requires proper acknowledgement The names of actual companies and products mentioned herein are the trademarks of their respective owners
8. rd identification number used by the system software to recognize the board Refer to the Dialogic Configuration Manager Physical Description Channels 4 3 2 1 Red Yellow Green Loopback 1 Ethernet Interface Connector 2 Good Link LED RJ 48C jacks Connectors 4 to external digital telephone network interface ww General Network Interface Alarm LED Power LED Reset LED SW1 Rotary switch to set board identification UNIX systems only Savy oe 8 Alarm LEDs Indicate network alarms for each trunk Red Alarm to indicate loss of signal Yellow Alarm to indicate loss of frame synchronization at far end of external network Green Indicates signal present powered up and receiving signal from external sources Loopback Indicates loopback mode is activated 9 CT MVIP Bus Termination Jumpers Bus signal is terminated when the corresponding jumper is installed JP2A CT Bus termination jumper JP2B MVIP Bus termination jumper 10 P3 CT Bus connector 11 ISA Edge Retainer 12 Signal Processing Daughterboard Note Signal must be terminated only on boards at each end of the CT Bus cable DCM utility to retrieve the board instance ID number s assigned to the board s in your system NOTE If you add a board to the system the existing board instance ID numbers may change depending upon the PCI bus and slot number where the new board is installed
Download Pdf Manuals
Related Search