Home

Denso BHT-100B Scanner User Manual

1. Status Indicators TIP The displayed battery level shows the terminal voltage of the battery not how _ much power is left The battery voltage level varies depending upon the operation of the BHT so the displayed level also may vary 28 Chapter 2 Getting Started the BHT and System Mode 2 3 5 Battery Replacement Notes E When is battery replacement needed If the Charge the battery or Replace the batteries appears on the LCD replace the rechargeable battery cartridge with a fully charged one or replace the dry cells with new ones respectively If you leave the BHT without replacing the rechargeable battery cartridge or dry cells the integrated calendar clock or data will no longer be backed up so that the calendar clock will stop or the message Contact your administrator Note the error number XXXX will appear on the LCD NOTE Be sure to turn the BHT off before battery replacement Replace the battery cartridge quickly Load a charged battery cartridge or new dry cells within 3 minutes after the removal to avoid data loss After battery replacement turn the BHT on and check its operation E If you will use the BHT more than one time per month Keep the battery cartridge loaded in the BHT E If you will not be using the BHT for more than one month Remove the battery cartridge from the BHT and then store the BHT To do so be sure to follow the procedure
2. SET SYSTEM L EXEC PROGRAM 40 SF and 1 keys Program Execution Allows you to select a desired user program to be executed immediately Refer to Subsection 2 5 3 1 Downloading Transfers user program files or data files from the host computer to the memory integrated in the BHT Downloading between the BHTs is also possible Refer to Subsection 2 5 3 2 Uploading Transfers user program files and data files stored in the memory of the BHT to the host computer Refer to Subsection 2 5 3 3 System Environment Settings Sets a variety of environmental condi tions an execution program message version English or J apanese calendar clock special bar code scanning parameters interface port communica tions parameters functions of the shift key magic keys and FUNC keys and resume function Shown at left is the BHT 100Q screen The BHT 100B screen displays 4 BARCODE instead of 4 QRCODE Refer to Subsection 2 5 3 4 5 and ENT keys C key 6 and ENT keys TEST L 7 ORCODE 2 MEMORY 3 BEEPER 4 AGING 5 COM 6 DISPLAY 7 KEY amp VIBRATION FILE SYSTEM INFO SYS ver ROM SIZE RAM SIZE SYS MESSAGE Japanese FONT JIS2C169 jrsici25 XXXX MB xMB Chapter 2 Getting Started the BHT and System Mode 41 Testing Used for the code reading test memory test beeper test aging test co
3. E Vertical Parity A vertical parity bit is a redundancy bit which is added to every character to be transmitted in order to check that data has been transmitted accurately The parity bit should be set to 1 or 0 depending upon the parity parameter setting to make the number of set bits in the character even or odd The receiver counts the number of set bits in the transmitted character code to make sure that it has the selected number even or odd of set bits The vertical parity bit is positioned immediately following the MSB Most signifi cant bit as shown below LSB MSB bO bl b2 b3 b4 b5 b6 For 7 bit data N Vertical parity bit LSB MSB bO b1 b2 b3 i b4 b5 i bs o7 For 8 bit data Vertical parity bit 114 Chapter 3 Communications Operations of the BHT 100Q 100B 3 3 2 Communications Parameters In System Mode and user programs written in BHT BASIC you may set the communi cations parameters listed below Communications Port Optical interface Direct connect interface Transmission Speed 2400 9600 19200 38400 300 600 1200 2400 4800 9600 57600 or 115200 bps 19200 38400 57600 or 115200 bps Character Length 8 bits 7 or 8 bits Vertical Parity None Odd even or none Stop Bit Length 1 bit 1 or 2 bits In System Mode Refer to Chapter 2 Subsection 2 5 3 4 5 Setting the communications environ ments In BHT BASIC To se
4. ee Serial eA Le T number Data text LeTIR E X D E X C lt Operands gt gt Operand 4 ID ID is a 2 digit hexadecimal and designated in 0000h through FFFFh in 2 bytes 0000h is assigned to the host computer Any of 0001h through FFFFh is assigned to the BHT as follows e The system sets an ID when the BHT is initialized e You may set an arbitrary ID in System Mode or by using the OUT statement in BHT BASIC 183 Appendix C A Typical Basic Operation What follows is a typical basic operation which helps you instruct the hands on user in practical bar code reading operation Application type Inventory Operation Power ON Read the 2D code or bar code on stock A gt Key in the quantity Read the 2D code or bar code on stock B gt Key in the quantity Repeat the above operation 6 Ready for data entry Record 00100 scrolls up so that record 00101 becomes ready for next data entry 2 Ready for data entry Filel 00 08 20 3 Bar code entry A Bring the bar code reading window to the bar code to be scanned and press the trigger switch Quantity entry Enter the quantity by ressing the numerical eys then press the ENT key A 0031323120786 B 20 1 Power ON Press the PW key to turn on the power 184 Appendices Appendix D Quality Assurance Standards D 1 Applicable Stand
5. E Using the stylus The BHT has a touch screen LCD that enables you to use touch keys and draw images on the touch screen with the stylus if you have defined those touch keys and graphics pad box in user programs respectively Before using the touch screen adjust it referring to Subsection 2 3 3 NOTE Press the touch screen only with the stylus that comes with the BHT Using the tip ofa pen or any pointed object will result in a damaged or broken LCD Strong pressure or impact applied to the LCD may also break the LCD 1 3 Setting the Backlight Pressing the right hand trigger switch M4 key while holding down the SF Shift key activates or deactivates the backlight function Backlight OFF The backlight function is OFF when you turn lt A the BHT power on Press the right hand trigger switch while holding down SF Right hand 1 trigger switch M4 Backlight ON Press the right If no key is hand trigger switch while d for at pressed for a holding down SF least 3 seconds Press any key except for the simultaneous depres sion of the right hand trigger switch and SF Backlight OFF The backlight function is kept ON Press the right hand trigger switch while holding down SF NOTE In user programs you can select the key to be used for activating or deactivating the backlight function instead of the in
6. A CAUTION e Never cover or wrap up the CU or AC adapter in a cloth or blanket Doing so could cause the unit to heat up inside deforming its hous ing resulting in a fire Always use the CU and AC adapter in a well ventilated area Do not place the CU anyplace where it may be subjected to oily smoke or steam e g near a cooking range or humidifier Doing so could result in a fire or electrical shock Keep the power cord away from any heating equipment Failure to do so could melt the sheathing resulting in a fire or electrical shock Do not insert or drop foreign materials such as metals or anything inflammable through the openings or vents into the CU Doing so could result in a fire or electrical shock E DENSO WAVE INCORPORATED does not assume any product liability arising out of orin connection with the application or use of any product circuit or application described herein Intellectual Property Precaution DENSO WAVE INCORPORATED DENSO WAVE takes reasonable precautions to ensure its products do not infringe upon any patent of other intellectual property rights of other s but DENSO WAVE cannot be responsible for any patent or other intellectual property right infringement s or violation s which arise from i the use of DENSO WAVE s product s in connection or in combination with other component s product s data processing system s or equipment or software not supplied from DENSO WAVE ii
7. Cable Connection between BHT and Host Computer BHT Connector I F Modem FG SD SD RD RD RS cs DR SG SG CD ER Cable Connection between BHT and Modem BHT Connector I F Printer FG SD RD busy RD busy SG SG Cable Connection between BHT and Printer Chapter 3 Communications Operations of the BHT 100Q 100B 3 3 Basic Communications Specifica tions and Parameters 3 3 1 Basic Communications Specifications Listed below are the communications specifications when the BHT exchanges data with a host computer through the CU 7000 optical interface or direct connect inter face cable Optical Interface Direct connect Interface Synchronization Start stop Transmission Speed 2400 9600 19200 38400 300 600 1200 2400 4800 9600 57600 or 115200 bps 19200 38400 57600 or 115200 bps Transmission Code J IS 8 bit codes JIS 7 or 8 bit codes Transmission Bit Order LSB Least significant bit first Vertical Parity None Even odd or none E Synchronization For accurate data transaction it is very important to synchronize the transmission between the sender and receiver To do this it is required to previously define the bit order and position the character length and the beginning and end of the character to be transmitted The start stop synchronization is an asynchronous system which synchronizes each character as a unit that is
8. Completed Selecting 1 DOWNLOAD on the SYSTEM MES SAGE transfer menu calls up the screen shown at left With this screen displayed the BHT waits for the system message file to be downloaded While the downloading operation is in progress the screen shown at left is displayed indicating the file name and the number of received records the total number of records To abort the downloading operation press the C key The screen will switch back to the SYSTEM MESSAGE transfer menu Upon completion of downloading the BHT dis plays the screen shown at left and beeps once Press the C key to return to the SYSTEM MES SAGE transfer menu NOTE When the BHT downloads the system mes sage file it creates a temporary file named SYSMSG FN3 in the user area If the user area is insufficient for creating the tem porary file therefore an error will result The created temporary file will be automati cally deleted after completion of downloading 103 If an error occurs during downloading If some error occurs during downloading the BHT beeps three times and shows one of the following screens with the prompt Retry To retry the download press the 1 and ENT keys to abort it press the 2 and ENT keys To return to the SYSTEM MESSAGE transfer menu press the C key DOWNLOAD Out of memory Retry MSZT 2 No DOWNLOAD File mismatch Retry MSZT 2 No DOWNLOAD Too many files
9. Retry MSZA 2 no E Problem The memory is insufficient for storing the system message file to be downloaded E Solution Press the 2 key to return to the SYSTEM MENU then delete unnecessary files in the memory Re fer to Subsection 2 5 3 7 E Problem You attempted to download a file other than the system message file E Solution Check whether the file you attempted to download is a system message file E Problem The current download will exceed the maximum of 80 files in the memory E Solution Press the 2 key to return to the SYSTEM MENU then delete unnecessary files in the memory Re fer to Subsection 2 5 3 7 104 DOWNLOAD SYSMSG FN3 Communication error Retr a MEE 2 No Chapter 2 Getting Started the BHT and System Mode E Problem Downloading has failed E Solution To retry downloading press the 1 key Pressing the 2 key returns to the SYSTEM MENU Check the interface port communications param eters and communications protocol type in the SET SYSTEM menu or perform the communica tions test in the TEST menu Refer to Subsection 2 5 3 4 5 and 5 5 13 2 Uploading the system message file ee Watting UPLOAD SYSMSG FN3 gt Loading Q BOOO G0000 Selecting 2 UPLOAD on the SYSTEM MESSAGE transfer menu calls up the screen shown at left With this screen displayed the BHT waits for the system message file to be uploaded While
10. System Program malfunction E Problem During execution of System Program the System Program has attempted to write onto the write pro tected area of the memory Xxxxxxxx Error address NOTE If this error occurs the BHT beeps five times _ for 0 1 second per beep E Solution Unload and reload the battery cartridge then turn on the power E Problem During execution of System Program the System Program has received an invalid command code Xxxxxxxx Error address NOTE If this error occurs the BHT beeps five times for 0 1 second per beep E Solution Unload and reload the battery cartridge then turn on the power 131 No execution program selected Contact your administrator No resume info has been retained Program restarts automatically Your settings in System Mode have been lost Will reset to defaults Execution program not selected E Problem No user program has been selected as an execu tion program to be run when the power is turned on NOTE If this error occurs the BHT beeps five times for 0 1 second per beep and then turns itself off E Solution Run System Mode and select an execution pro gram in the SET SYSTEM menu For the selecting procedure refer to Chapter 2 Subsection 2 5 3 4 1 Resume data lost E Problem No resume data has been retained since the BHT was not normally turned off and then left with no battery cart
11. xiii Chapter 1 Quick Guide Chapter 2 Getting Started the BHT and System Mode Chapter 3 Communications Operations of the BHT Chapter 4 Error Messages Chapter 5 Handling the CU 7000 Option Appendices Chapter 1 Quick Guide This chapter describes the basic operating method of the BHT and the related notes 1 1 Reading 2D Codes and Bar Codes ce BHT 100Q siesevectecdecaseccsdcccansvashitchacesens faniedtvcdecscseltsslbveatecatededdededduecducesesecapetbiorbtvederenens 2 aia P Ea OO E EE isso Sane edt teas daa ce head ose dt AAD eel 4 1 2 Setting and Using the Hand Strap and StylUS oo eect eee eeeeeeeeeeeeeeteeeeeeeneeees 6 13 SMEG the Backlight sisisi sirina ididiin i eii ei 8 L4 Usmo he KOy 07 8 Renee een ee RR ae a N aa 9 UGB Te aL Aao DAE EEEE a E A A A 10 1 1 Reading 2D Codes and Bar Codes BHT 100Q Turn the BHT power on bring the reading window to the target code and press the trigger switch The BHT 100Q turns three marker LEDs on to indicate the scanning range and the illumination LED to scan the code Keep the BHT stationary in a position where the target code lies between the right and left markers and the center marker comes to the center of the target code Hold the reading window 4 to 14 cm 1 6 to 5 5 inches away from codes to be scanned When the BHT has read the code successfully the indicator LED will illuminate in green and the markers will go off 4to 14cm
12. 1 DOWNLOAD TIP Without the host computer you may directly copy the BHT system parameter file between two BHTs one BHT runs UPLOAD and the other DOWNLOAD For the preparation to be made beforehand refer to NOTE on page 47 If you select the 2 UPLOAD the system will set up the BHT system parameter file based on the current settings and upload it to the host computer After that the created file will be deleted If you select the 1 DOWNLOAD the BHT will receive the BHT system parameter file from the host computer and apply the stored values After that the received file will be deleted For uploading downloading the BHT will use the communications parameters com munications protocol and interface port specified in Subsection 2 5 3 4 5 Setting the communications environments SYSTEM PARAMETER transfer menu SYSTEM PARAMETER Pressing the 3 key while holding down the SF key on the SYSTEM MENU calls up the screen shown i at left 2 UPLOAD 1 DOWNLOAD Downloads the BHT system pa rameter file to the user area of the BHT N UPLOAD Uploads the BHT system pa rameter file stored in the BHT Select a desired item by using the numerical keys or M1 and M2 keys then press the ENT key Press the C key to return to the SYSTEM MENU 95 8 1 Downloading the BHT system parameter file DOWNLOAD Waiting 1 DOWNLOAD __BHT SYS Loading YYYYYZZZZZZ 4
13. COL TYPE screen calls up the screen shown at left Enter the ID number of the BHT by using the nu merical keys and then press the ENT key If you do not need to modify the current setting press the ENT key only mc An ID number should be five digit decimal NOTE character string The entry range is from 00001 to 65535 If the entry value is less than five digits the ENT key will be deacti vated If you make a wrong entry press the BS key to delete it and then enter the correct data To return to the SET COM menu press the C key 70 Chapter 2 Getting Started the BHT and System Mode 4 6 Defining the functions of the shift key magic keys and function keys SET KEY poe Sinelsam KEY 2 M1 KEY B iM2 KEY 4 M3 KEY S M4 KEY G FUNC KEY Selecting the 6 KEY on the SET SYSTEM menu calls up the screen shown at left Highlighted is the current setting 1 SHIFT KEY Switches to the shift key defini tion screen 2 M1 KEY Switches to the M1 key definition screen 3 M2 KEY Switches to the M2 key definition screen 4 M3 KEY Switches to the M3 key left hand trigger switch definition screen 5 M4 KEY Switches to the M4 key right hand trigger switch definition screen 6 FUNC KEY Switches to the function key ON OFF screen Select a desired screen by using the numerical keys or M1 and M2 keys and then press the ENT key To return to t
14. DOWNLOAD __BHT SYS Completed Selecting 1 DOWNLOAD on the SYSTEM PARAM ETER transfer menu calls up the screen shown at left With this screen displayed the BHT waits for the BHT system parameter file to be downloaded While the downloading operation is in progress the screen shown at left is displayed indicating the file name and the number of received records the total number of records To abort the downloading operation press the C key The screen will switch back to the SYSTEM PARAMETER transfer menu Upon completion of downloading the BHT dis plays the screen shown at left and beeps once Press the C key to return to the SYSTEM PARAM ETER transfer menu 96 Chapter 2 Getting Started the BHT and System Mode If an error occurs during downloading If some error occurs during downloading the BHT beeps three times and shows one of the following screens with the prompt Retry To retry the download press the Land ENT keys to abort it press the 2 and ENT keys To return to the SYSTEM PARAMETER transfer menu press the C key DOWNLOAD Out of memory Retr MSZT 2 No DOWNLOAD File mismatch Retry PREZ 2 No DOWNLOAD Too many files Re ia Satie E Problem The memory is insufficient for storing the BHT system parameter file to be downloaded E Solution Press the 2 key to return to the SYSTEM MENU then delete unnecessary files in the memory
15. ROM SIZE RAM SIZE SYS MESSAGE Japanese x jrs2c125 3jrsici2 gt u H v B la B o U XXXX xx Selecting the 6 VERSION on the SYSTEM MENU calls up the screen shown at left displaying the system program version memory sizes system message version and J IS font types and their ver sions Press the C key to return to the SYSTEM MENU The following font types are displayed J 1S2 16 JIS Level 2 font 16 dot JIS1 16 JIS Level 1 font 16 dot J IS2 12 JIS Level 2 font 12 dot JIS1 12 JIS Level 1 font 12 dot 92 Chapter 2 Getting Started the BHT and System Mode 7 Deleting Files You may delete a program file or data file stored in the memory File deletion menu DELETE FILE Pressing the 0 key while holding down the SF key on the SYSTEM MENU calls up the screen shown KKM KKK MK KKK ERE E E S E st at left XXXXXXXX XXX XXXXXXXX XXX XXXXXXXX XXX Use the M1 and M2 keys to move the cursor to the XXXXXXXX XXX XXXXKXXKXX XXX file to be deleted then press the ENT key XXXXXXXX XXX XXXXXXXX XXX XO XXX Press the C key to return to the SYSTEM MENU XXXXXXXX XXX XXXXXXXX XXX XXXXXXXX XXX XXXXXXXX XXX XXXXXXXX XXX XXXXXXXX XXX DELETE FILE If no file is resident in the memory the message shown at left appears Be ake ake ake ke oie gt e te ske ote oe te k gt k oe NO FILE EXISTS AA ne Press the C key to return to the SYSTEM MENU Deletion
16. The names of the JIS font files are FNT16J1 FN3 JIS Level 1 font 16 dot FNT16J2 FN3 JIS Level 2 font 16 dot FNT12J1 FN3 JIS Level 1 font 12 dot FNT12J2 FN3 JIS Level 2 font 12 dot E User Programs You can develop application programs to meet individual job requirements by using the BHT BASIC Compiler To download those user programs to the BHT use Ir Transfer Utility C Ir Transfer Utility E Transfer Utility 16 Chapter 2 Getting Started the BHT and System Mode 2 2 Components and Functions Indicator LED IIluminates in green when the BHT has successfully read a code Touch screen LCD liquid crystal display Shows the characters and graphic patterns You may directly touch the display with the stylus for data entry Trigger switch M4 key Press this switch to start code reading Hand strap Be sure to put your NNSS hand through this strap to prevent you from dropping the BHT accidentally Trigger switch J M3 key Press this switch to start code reading Optical interface port Used to exchange data programs with the host computer via its integrated IR Connector cover port or via the optical communication Inside this cover is the direct connect interface unit CU 7000 port Reading window Stylus Rechargeable battery cartridge or dry battery cartridge Main power source of the BHT Release button Press this button to remove the battery cartridge 17 The
17. BHT system parameter file or system message file cannot be set up E Solution Press the C key to return to the SYSTEM MENU and delete unnecessary files Refer to Chapter 2 Subsection 2 5 3 7 E Problem Uploading has failed E Solution To retry uploading press the 1 key Pressing the 2 key returns to the SYSTEM MENU Check the interface port communications param eters and communications protocol type in the SET SYSTEM menu or perform the communica tions test in the TEST menu Refer to Chapter 2 Subsection 2 5 3 4 5 and 5 5 It is also necessary to check the communications parameters setup of the host computer E Problem Uploading the BHT system parameter file has failed E Solution To retry uploading press the 1 key Pressing the 2 key returns to the SYSTEM MENU Check the interface port communications param eters and communications protocol type in the SET SYSTEM menu or perform the communica tions test in the TEST menu Refer to Chapter 2 Subsection 2 5 3 4 5 and 5 5 It is also necessary to check the communications parameters setup of the host computer 138 This chapter describes the handling procedure of the CU 7000 the interfacing with the host computer and the charging of the rechargeable battery cartridge 5 1 FUNGLIONS GFINE CU 7000 vma a a 140 52 VGOMpPONents and PUNMCHGNS 5 sasisnsiscsssssacs ionni err ainera eeann anaa ioiei MARETE RE REDES 140 5 3 Applying Pow
18. Getting Started the BHT and System Mode 2 Communications protocol option screen SET PROTOCOL lt CONNECTOR gt ON OFF 2 H PARITY ON OFF 3B LINKUP TIME None 60 9 120 4 FIELD SPACE Data Selecting 2 PROTOCOL on the SET CONNECTOR screen calls up the screen shown at left Highlighted is the current setting 1 SERIAL No 2 H PARITY 3 LINKUP TIME 4 FIELD SPACE Selects whether or not the system will add serial num bers to data blocks Selects whether or not the system will add a horizontal parity Selects the timeout length in seconds to be applied when a link is to be established Selects whether space codes in the tail of a data field will be ignored or handled as data Select a desired item by using the numerical keys or M1 and M2 keys Then select a desired setting by using the SF M1 and SF M2 keys To return to the SET CONNECTOR screen press the C key NOTE If the BHT Ir protocol has been selected the serial number and horizontal parity settings will be ignored 67 4 5 3 Setting the interface port SET COM PORT 1 BASTC Optical Connector 2 SYSTEM MODE Optical Connector 1 BASIC SYSTEM MODE Selecting the 3 COM PORT on the SET COM menu calls up the screen shown at left Highlighted is the current setting Selects the optical or direct connect i
19. TRANSMIT SPEED 19200 38400 57600 115200 SYSTEM MESSAGE 1 DOWNLOAD 2 UPLOAD 42 and Lkeys Deleting files Deletes a program file or data file stored in the memory Refer to Subsection 2 5 3 7 Downloading uploading the BHT system parameter file Downloads or uploads the system parameter file Refer to Subsection 2 5 3 8 Setting the remote wakeup parameters Sets the remote wakeup parameters Refer to Subsection 2 5 3 9 Downloading uploading the system message file Downloads or uploads the system message file Refer to Subsection 2 5 3 10 2 5 2 Operating in System Mode Chapter 2 Getting Started the BHT and System Mode Some functions in System Mode require several screens to be shifted as shown in the example below 1 Calling up the desired set screen First select a desired item on the current screen by using the numerical key or the M1 and M2 keys so as to highlight the desired item Press the ENT key to establish the selected item and proceed to the subsequent screen To return to the preceding screen press the C key Press the 4key or use M1 and M2 keys to select 4 SET SYSTEM Press the 5 key or use M1 and M2 keys to select 5 COM Press the 3 key or use M1 and M2 keys to select 3 COM PORT BHT 100Q SYSTEM MENU L EXEC PROGRAM 2 DOWNLOAD 3 UPLOAD 4 SET SYSTEM S TEST 6 VERSION ji ENT key SE
20. is designed to recover from those errors as frequently as possible What follows is the BHT protocol for phases 1 through 3 Phase 1 Establishment of Data Link E Normal phase 1 The sending station transmits an ENQ to the receiving station Upon receipt of an ACK from the receiving station the sending station shifts to phase 2 Sending station ENQ Receiving station ACK To phase 2 E Phase 1 with iterated ENQ transmission due to no response or invalid response If the sending station receives no response or any invalid response from the receiving station in response to an ENQ sent it iterates sending of an ENQ at three second intervals up to 10 times If the sending station receives an ACK before sending an ENQ ten times it shifts to phase 2 Sending Receiving station ENQ station 3 seconds ees ENQ 3 seconds e B ma pe To phase 2 TIP You may modify the number of ENQ iterations for the sending station The default is 10 times at three second intervals For details refer to the SET PROTOCOL screen in System Mode pp 65 and 67 and the XFILE statement given in BHT BASIC Programmer s Manual BHT 100 series 164 Appendices E Abnormal termination of phase 1 Abort of phase 1 If the sending station receives no ACK from the receiving station after sending an ENQ 10 times in succession it sends an EOT to the receiving station afte
21. the use of DENSO WAVE s products in a manner for which the same were not intended nor designed or iii any modification of DENSO WAVE s products by other s than DENSO WAVE Licensed under one or more of the following U S patents 4 570 057 4 766 300 4 894 523 5 021 642 5 038 024 5 081 343 5 095 197 5 144 119 5 144 121 5 182 441 5 187 355 5 187 356 5 218 191 5 233 172 5 258 606 5 288 985 E Proper Care of the BHT and CU Clean the housings battery cartridge terminals and CU 7001 charge terminals with a dry soft cloth Before cleaning be sure to turn the BHT power off and unplug the AC adapter of the CU e Never use benzene alcohol or other or ganic solvents The housing may be marred or the paint may come off Take care of me with a dry soft cloth e Never rub or strike the liquid crystal dis play LCD with anything hard The LCD surface will be easily scratched or bro ken LD 4 NO WAY 2 AKA LAE Thinner Benzine e When cleaning the keypad do not scrub the surface too hard and do not pull on the keys Doing so may break the keys or cause the keypad to dislocate e Ifthe BHT or CU becomes smudged moisten a soft cloth with neutral detergent and wring it out thoroughly Wipe the BHT or CU with the cloth and then go over it again with a dry cloth Dust or dirt accumulating on the clear plate of the reading window will affect reading performance If you use the BH
22. 1 Interface Connector and Pin Assignment vw L111 2 Interface Cable Connection ccccccccccecessesesssssessssseesseraeesesseeeessnneeeseees 112 3 3 Basic Communications Specifications and Parameters seessserssnresr 113 3 3 1 Basic Communications Specifications sssssessrseisiseinriersrernniernrennns 113 3 3 2 Communications Parameters esssssssessesirsisirsisrisisistnttnisintnttnisintnnnnernnn nennt 115 3 4 Communications Protocols 3A 1 BHTEPrOtoCO linn aeaee e a e a ii PE MOVER APE E TAE A A 2 Control Characters 3 Basic Format of Transmission Messages cecceeceeceeeeeeeeteteeeeteeteteaeeaes 119 E 9 Ea r A a e A3 ON A AAAA AE E AAAS AAAA 120 3 4 2 BHT IP Protocol saci cies sciise ececcededececdederceverv ered abenan edidi inir dubusbiebalh aaae 122 EIV Oveni oA Aaaa aT O aaas 122 2 Control Characters riiin vae 123 3 Basic Format of Transmission Messages sessssesssrerserresi 125 AI TAFONA pio aa rana eei eaa A we teeaseendovasoieveds a AARNE 126 Chapter 3 Communications Operations of the BHT 100Q 100B 3 1 Infrared Communication The BHT has an integrated infrared IR communications device which enables wire less transfer of programs and data between the BHT and the host computer and between the BHTs instead of the conventional wire transfer The IR communications device features the following e Wireless communications e Small and lightweight design e High transmission speed e
23. 1 6 to 5 5 Indicator LED IIluminates in green when the BHT has successfully read the code Touch screen LCD Shows the scanned image of a code lying inside the scanner s view if the view finder is set to ON Markers Trigger switch M3 key Trigger switch M4 key PW key e The markers show the left to right scanning range When the scanning distance is 8 5 to 9 5 cm 3 3 to 3 7 inches they indicate almost the center of the up down scanner s view If the distance is out of the range those markers will deviate from the center If the BHT fails to read due to specular effects or other factors change the scanning angle of the reading win dow or the distance from codes as shown at right and try it again Specular effects occur when the reflec tion of the light from the code becomes excessively strong This can easily happen when the reflecting surface is polished or covered with vinyl The code reading procedure may differ depending upon the application used so follow the application s manual Chapter 1 Quick Guide Before reading 2D codes or bar codes clean those labels if stained Avoid using the BHT in direct sunlight The BHT might fail to read correctly To read 2D codes or bar codes on curved surfaces apply the BHT to the target code so that the code comes to the center of the scanning range indicated by the markers Depending upon the code size or cell pitch the proper scanning distanc
24. 200 dots wide by 16 dots high Screen mode Font size Letter type Dots W xH Chars x Lines Single byte Standard size ANK Regular size 12 x 12 16 x 25 ANK mode 12 dot Double width 24x12 8x25 Double height 12 x 24 16 x 12 Quadruple size 24 x 24 8x12 Two byte Standard size Full width Regular size 16 x 16 12x19 Kanji mode 16 dot Double width 32x16 6x19 Double height 16 x 32 12x9 Quadruple size 32 x 32 6x9 Half width Regular size 8x 16 25x19 Double width 16 x 16 12 x 19 Double height 8 x 32 25x9 Quadruple size 16 x 32 12x9 Small size Full width Regular size 12 x 12 16 x 25 12 dot Double width 24x12 8x25 Double height 12 x 24 16 x 12 Quadruple size 24 x 24 8x12 Half width Regular size 6x12 33x 25 Double width 12 x 12 16 x 25 Double height 6x 24 33x 12 Quadruple size 12 x 24 16x12 Calendar Clock Reading Confirmation ANK Alphanumerics and Katakana Year month day hour minute and second e Year Two digits with auto correction on February 29 for year 1901 to 2099 Indicator LED Red amp green beeper and vibrator 150 Appendices 2 Readable Codes The values given below are based on the scanning reference position shown in the next item 3 Skew angle 360 1 QR Codes Model 1 and Model 2 and MicroQR Code size Cell pitch 21 x 21 cells to 85 x 85 cells 0 25 mm 9 8 mils 21 x 21 cells to 61 x 61 cells 0 33 mm 13 0 mils 105 x 105 cells 1 11 x 11 cells to 17
25. 2D code model and error correction level to the tail of 2D code data when it reads a 2D code NOTE This setting takes effect not only in the reading test in System Mode but also in any other operations Do not disturb this setting unless necessary Option data format e QR code a Data read gt lt Option data n 1 n 2 n 3 n 4 n 5 n 6 n 7 1 2 1 Error 3 ns n Q Model Version correc Mask ee eee level Example If a code read is QR code Model 2 Version 5 Error correction level M and mask number 6 then the option data below will follow Data read Q2VO05M6 59 PDF417 lene Data read Option data 4 1 2 gt n 1 n Example If a code read is PDF417 Error correction level 4 12 rows and 2 digits then the option data below will follow Data read Y1041202 n 1 n 2 n 3 n 4 n 5 n 6 n 7 n 8 Error aoe correction No of rows No of digits level yn paserved e MaxiCode k Data read j _ n 1 n 2 1 2 gt n 1 n x Mode Example If a code read is MaxiCode and Mode 4 then the option data below will follow Data read X4 e Data Matrix je Data read gt Option data y n 1 n 2 n 3 n 4 n 5 n 6 n 7 n 8 n 9 n 10 n 11 Ze Reserved Error correction level No of cells height No of c
26. 7000 on which the BHT is put and a host computer The DCE is one piece of equipment connected to the intermediate point between the DTE and the communications line It terminates communications lines and exchanges information between those lines without any change in contents such as modem 147 Appendix A Specifications A 1 BHT 100Q ARDS SPRGOUCES DECIR SOONG siaina e EEA ai ERRARE 149 BAE E ea A O a 1 o T DOREN A ENEO ERLEEN A PEER EEEIEI EAEEREN 151 3 Scanning Performance sfcsccseccvscuscuee reo ies ddidercecsceaeuseuseea esteitd 153 4 Interface Specifications iisssisssscissssraiesessasesdunsasaacnsazaacaasnvrynysparaasastenannass 155 A 2 BHT 100B 1 Product Specifications 2 Bar Code Specifications 3 Interface Specifications A 3 CU 7000 n a 1 Product Specifications 2 Charging Requirements CU 7001 cceeeeeeeeeeeeesteteesteeenetneeseeeneeaes 161 3 Interface Specifications 162 Appendix B Communications Protocol Details 0 0 0 cceceeceeeeeeeeeeeeteeeteeeesteeeneeneteeeaes 163 B 1 BHT protocol 1 Transmission Control Sequences 2 Aborting Data Transmission 0 0 cecccceeeeeceeeeeeteesneeteeneeseeseeeseeieeneeenes 3 BCC for Horizontal Parity CHECKING 0 ce eeeeeeeeeeeeeeeeeeeetneeeetnetteeeeeaes 172 B 2 BHT IF protocol iiciei sce eeeeccerereens 173 1 Transmission Control SEQUENCES 0 eect eect eteeeteeteeeeeseeteesnetieteeeaes 173 2 Abortin
27. ACK before receiving a NAK 10 times in succes sion it continues the subsequent message transmission Sending i Receiving station Data text m station p B N NAK N PEE e D ata text m 1 ee If the sending station receives a NAK 10 times in succession or it fails to send a same transmission block it shifts to phase 3 to terminate the message transmis sion abnormally Even if phase 3 terminates normally the transmission results in an abnormal end Sending Receiving station Data text m 1 station oe me B a wa Data aa m 10 Occurrence of an error To phase 3 167 E Phase 2 with EOT If the sending station receives an EOT anytime during phase 2 it shifts to phase 3 to terminate the message transmission abnormally Even if phase 3 terminates normally the transmission results in an abnormal end Sending 1 Receiving station i station 1 tee Occurrence of an error To phase 3 E Phase 2 with iterated ENQ transmission due to no response or invalid response If the sending station receives no response or any invalid response from the receiving station in response to a transmission block sent it iterates sending of an ENQ at three second intervals up to nine times If the sending station receives an ACK before sending an ENQ nine times it continues the subsequent message transmissio
28. BHT and any target stations within the effective infrared radiation range usually 10 to 80 cm 3 94 to 31 50 e Shield the IrDA interface from direct sunlight ambient intense lighting inverter driven fluorescent lighting in particular and other potential sources of infrared radiation Sources to watch out for include remote control units for television sets and the like Host computer BHT For a host computer having no IrDA interface port use the optical communications unit CU 7000 option connected to the host via an RS 232C interface cable Put the BHT in the CU 7000 as shown below 10 Chapter 2 Getting Started the BHT and System Mode This chapter summarizes the BHT system configuration and describes the operation including preparation and System Mode which is required for the efficient use of application programs 2 1 BHT System COM FUSED eee eienaar erna AAAA aeiiae eneee enient 12 2 2 Components and FUNCHOMS vesiceccisciisis ceceecedeceececcecceeeccesshtwecnesdasenseendeadcecedlonsceveeseteed 17 2 3 PRP ABU scoansasranvatenss issaacavarexivigoosaracanatnnih datas tsassans vriveis T 19 2 3 1 Setting up 1 Loading the Battery Cartridge ccececseseteeeeeteeeeeteeeeeeeeeaes 19 2 3 2 Setting up 2 Setting the Calendar ClOCK c cecececceeeeeeeeceeeeteetieeeeeseeeneeneeaees 23 2 3 3 Adjusting the LCD Contrast Beeper Volume and Touch Screen and Switching the Beeper amp Vibrator oo cece ce eee
29. BHT without recharge or battery replacement after the Level 1 message appears the BHT displays the following Level 2 message beeps five times and then turns itself off Depending upon the battery level the beeper may not sound five times When driven by the When driven by the dry battery cartridge rechargeable battery cartridge Charge the Replace the battery batteries If the BHT is driven by the rechargeable battery cartridge recharge or replace it if it is driven by the dry battery cartridge replace the dry cells 21 NOTE When replacing dry cells always replace both of them with new alkaline manga nese batteries LR6 e You may charge the rechargeable battery cartridge with the optional CU 7001 communication unit or optional C 700 C 750 charger For the charging proce dure using the CU 7001 refer to Chapter 5 For that using the C 700 C 750 refer to the C 700 User s Manual C 750 User s Manual e If the Charge the battery or Replace the batteries message appears after the BHT undergoes any shock or impact turn the power off and on and then check the battery output level The battery may not have run out A WARNING Only use the dedicated charger CU 7001 C 700 or C 750 for charging the rechargeable battery cartridge Using a different type of charger could cause battery rupture or leakage of battery fluid and result in a fire bodily injury or serious damage to property AN
30. CAUTION Never charge a wet or damp rechargeable bat tery cartridge Doing so could cause the batteries to break gen erate heat rupture or burn 22 Chapter 2 Getting Started the BHT and System Mode 2 3 2 Setting up 2 Setting the Calendar Clock Turn the BHT on by pressing the PW key The following message will appear Set the current date and time Q 0 O01 01 80 00 P rd In the following cases the above message will appear In such instances it is necessary to set the date and time The indication 00 01 01 00 00 will differ depending upon the calendar clock state e The BHT is first turned on from the time of purchase e The BHT is turned on after the memory backup power source is com pletely discharged SET DATE TIME Use the numerical keys to enter the year only the last two digits month day hour and minute in this order If the data is in one digit add a 0 zero preceding the data 07 17 801 98 00 0 704 19 16 00_ NOTE For the year be sure to enter the last two digits of the year For the hour enter it in the 24 hour format If any of the year month day hour and minute is not entered the ENT key will be deactivated If you make a wrong entry press the BS key to delete it and then enter the correct data Example To set 2000 April 19 at 4 00 p m Press 0 0 O 4 1 9 1 6 0 and 0 Then press the ENT key to register the new setting If
31. CU 7000 Option Describes the handling procedure of the CU 7000 the interfacing with the host compu ter and the charging of the rechargeable battery cartridge Appendix A Specifications Appendix B Communications Protocol Details Appendix C A Typical Basic Operation Appendix D Quality Assurance Standards E Technical Terms Used in This Manual Source Program and Object Program User Program Generally a source program is translated into an object program by acompiler This manual calls an object program a user program BHT BASIC This manual expresses BHT BASIC3 0 and BHT BASIC3 5 as BHT BASIC E Related Publications BHT BASIC Programmer s Manual BHT 100 series Transfer Utility Guide Ir Transfer Utility C Guide Ir Transfer Utility E Guide E Screen Indication The lettering in the screens in this manual is a little different from that in the actual screens File names used are only for description purpose so they will not appear if you have not set files having those names SAFETY PRECAUTIONS Be sure to observe all these safety precautions Please READ through this manual carefully It will enable you to use the BHT and CU correctly Always keep this manual nearby for speedy reference Strict observance of these warning and caution indications are a MUST for preventing accidents which could result in bodily injury and substantial property damage Make sure you fully understand all definitions of these term
32. E Problem A System Program error has occurred NOTE If this error occurs the BHT beeps five times for 0 1 second per beep and then turns itself off E Solution Contact your nearest dealer Low battery indication Level 1 E Problem When the power is turned on or off or during ex ecution of program System Mode or application the battery output level has dropped below a specified lower level limit NOTE If low battery is detected the BHT displays this message for approx 2 seconds and beeps three times for 0 1 second per beep After that it will resume previous regular operation E Solution The battery recharge or replacement time will come soon If the BHT is loaded with the rechargeable battery cartridge replace or charge it For the charging procedure refer to Chapter 5 Section 5 5 If the BHT is loaded with the dry battery cartridge replace the dry cells 129 When the rechargeable battery cartridge is loaded Charge the battery When the dry battery cartridge is loaded Replace the batteries Set the current date and time O 01 701 88 00 te Se 7 Low battery indication Level 2 E Problem When the power is turned on or off or during ex ecution of program System Mode or application the battery output level has lowered NOTE If lower battery is detected the BHT beeps five times for 0 1 second per beep and then turns itself of
33. INITIALIZE plays the screen shown at left for a second and turns itself off automatically Completed NOTE Do not turn the BHT off until the above initialization completion screen appears A too early powering off will interrupt initialization requiring you to initialize the BHT again e If the message Contact your administrator Note the error number 2XXX appears although the initialization has completed initialize the BHT again e If you initialize the BHT after downloading user programs and data all of those programs and data stored in the target memory area will be lost Download them again if necessary e Initialization will reset the LCD contrast level refer to Subsection 2 3 3 com munications conditions and other settings to the factory defaults so modify them if necessary After initialization be sure to set the calendar clock refer to Subsection 2 3 2 38 Chapter 2 Getting Started the BHT and System Mode 2 5 Operating in System Mode System Mode is an operating software exclusively designed for the effective use of the BHT which includes various functions as shown on the following pages 2 5 1 Starting System Mode To start up System Mode turn the BHT power on while holding down the SF and 1 keys This operation calls up the SYSTEM MENU on the LCD as shown below SYSTEM MENU 1 EXEC PROGRAM DOWNLOAD The function selected is highlighted white on black with the cursor
34. M2 keys and then select a desired setting by using the SF M1 and SF M2 keys To increase the decode level press the SF HM2 keys to decrease it press the SF M1 keys To increase the number of digits to be read for ITF and Codabar press the SF HM2 keys to decrease it press the SF M1 keys Press the ENT key To return to the SET SYSTEM menu press the C key Black and white inverted label reading function INVERT This function makes it possible to read white bars on a black background NOTE When this function is activated the BHT 100Q cannot read codes other than QR codes 58 Chapter 2 Getting Started the BHT and System Mode Marker You may select the marker ON OFF mode from the following 0 Driven by the trigger switch 1 Fixed to ON 2 Fixed to OFF NOTE If you select 1 Fixed to ON the markers will keep ON so that power consump tionis higher than that in other modes and the battery working time becomes short Do not disturb this setting unless necessary View Finder If the View Finder is set to ON the LCD shows the scanned image of a code lying inside the scanner s view when you scan the code Upon completion of scanning the view finder display goes off NOTE Setting the View Finder to ON decreases the scanning speed TIP You may set the view finder also by using the OUT statement in BHT BASIC Option Data If the Option Data is set to ON the BHT 100Q will add option data containing
35. OTT 75 6 Systemi Information cscs esti aeactedce versuri a Un cacceneen eee 92 Pda MOST OE IG FES ieee ened acre AOE E E ET 93 8 Downloading Uploading the BHT System Parameter File aese 95 9 Setting the Remote Wakeup cccececceeeeeeeeeeenecseeeeesnetsetseeneesneeneeaees 101 10 Downloading Uploading the System Message File 00 eects 102 11 2 1 BHT System Configuration The BHT barcode data collection system requires the following hardware as well as the BHT Bar Code Handy Terminal which reads 2D codes or bar codes and accepts key entry as illustrated below e Host computer Allows you to edit manage and download pro grams and data as well as downloading sys tem programs For host computers having no IrDA interface ports the optional CU 7000 optical communications unit and RS 232C interface cable are available e CU 7000 option e RS 232C interface cable option Exchanges programs and data with the BHT via the IrDA interface and with the host computer via the RS 232C interface Connects the CU 7000 and the host computer Direct cable connection between the BHT and host computer is also possible Optional software includes the BHT BASIC Extension Library BHT BASIC Compiler Ir Transfer Utility C Ir Transfer Utility E and Transfer Utility System Configuration BHT Optical Communications Ol option RS 232C Interface RS 232C BHT BASIC Compiler Interface Optica
36. PD3 SAMPLE 8 amp PD3 SAMPLEOOSO PD3 SAMPLE10 PD3 SAMPLE11 PD3 SAMPLE12 PD3 SAMPLE13 PD3 SAMPLE14 PD3 SAMPLE15 PD3 SAMPLE16 PD3 SAMPLE17 PD3 SAMPLE18 PD3 SAMPLE19 PD3 SAMPLE20 PD3 SIZE bbbbb FREE yyyyy TEST FILE SAMPLEO1 PD3 QG O 0O4096G bytes OK SIZE bbbbb FREE yyyyy TEST FILE SAMPLEO1 PD3 Q O04096G bytes NG SIZE bbbbb FREE yyyyy Chapter 2 Getting Started the BHT and System Mode Selecting 8 FILE on the TEST menu calls up the screen shown at left If any of the files stored in the memory is defec tive an asterisk or plus sign will be prefixed to the defective file name s For details about the and refer to Subsection 2 3 6 3 Selecting a file on this screen will show the file size and the test result To select a file use the M1 and M2 keys to move the cursor to the desired file If there are more than 20 files the screen will scroll Highlighted is the currently selected file Press the C key to return to the TEST menu The file name file size and test result OK or NG appear as shown at left Press the C key to return to the file selection screen NOTE If a defective file is found delete it or overwrite it with the same name file Even defective the file can be uploaded on the UPLOAD menu It is therefore recommended that important files be uploaded before deleted 91 6 System Information SYSTEM INFO SYS Ver x
37. Re fer to Subsection 2 5 3 7 E Problem You attempted to download a file other than the BHT system parameter file E Solution Check whether the file you attempted to download is a BHT system parameter file E Problem The current download will exceed the maximum of 80 files in the memory E Solution Press the 2 key to return to the SYSTEM MENU then delete unnecessary files in the memory Re fer to Subsection 2 5 3 7 97 DOWNLOAD BAT sS S Communication error Retry MEZA 2 No E Problem Downloading has failed E Solution To retry downloading press the 1 key Pressing the 2 key returns to the SYSTEM MENU Check the interface port communications param eters and communications protocol type in the SET SYSTEM menu or perform the communica tions test in the TEST menu Refer to Subsection 2 5 3 4 5 and 5 5 It is also necessary to check the communications parameters setup of the host computer 8 2 Uploading the BHT system parameter file UPLOAD Waiting V UPLOAD BHT SYS Loading Q BOOO O0000 Selecting 2 UPLOAD on the SYSTEM PARAM ETER transfer menu calls up the screen shown at left With this screen displayed the BHT waits for the BHT system parameter file to be uploaded While the uploading operation is in progress the screen shown at left is displayed indicating the file name and the number of sent records the total nu
38. Setting the communications parameters for the direct connect interface SET CONNECTOR 1 PARAMETER 2 PROTOCOL Selecting 2 CONNECTOR on the SET COM menu calls up the screen shown at left 1 PARAMETER Switches to the commu nications parameters set ting screen 2 PROTOCOL Switches to the commu nications protocol option screen Select a desired screen by using the numerical keys or M1 and M2 keys and then press the ENT key To return to the SET COM menu press the C key 1 Communications parameters setting screen SET PARAMETER lt CONNECTOR gt 1 TRANSMIT SPEED 300 600 1200 2400 483800 9600 19200 38400 57600 115200 2 PARITY BIT Odd Even 3 DATA BIT 7bits 4 STOP BIT 2bits Selecting 1 PARAMETER on the SET CONNEC TOR screen calls up the screen shown at left Highlighted is the current setting 1 TRANSMIT SPEED Sets the transmission speed 2 PARITY BIT Sets the vertical parity none odd or even 3 DATA BIT Sets the character length 4 STOP BIT Sets the stop bit length Select a desired item by using the numerical keys or M1 and M2 keys Then select a desired setting by using the SF M1 and SF HM2 keys To return to the SET CONNECTOR screen press the C key NOTE If the BHT Ir protocol has been selected the parity bit character length and stop bit length settings will be ignored 66 Chapter 2
39. Subsection 2 5 3 7 and 2 E Problem Downloading has failed E Solution To retry downloading press the 1 key Pressing the 2 key returns to the SYSTEM MENU Check the interface port communications param eters and communications protocol type in the SET SYSTEM menu or perform the communica tions test in the TEST menu Refer to Subsection 2 5 3 4 5 and 5 5 It is also necessary to check the communications parameters setup of the host computer E Problem You attempted to download an invalid program file E Solution Check whether the program file you attempted to download is available to your BHT model If itis not available download the appropriate program 50 3 Uploading UPLOAD L ONE FILE 2 ALL FILES B HT lt gt HT COPY Chapter 2 Getting Started the BHT and System Mode Selecting 3 UPLOAD on the SYSTEM MENU calls up the screen shown at left 1 ONE FILE Uploads a user program file or data file stored in the memory 2 ALL FILES Uploads all user program files object programs and all data files stored in the memory 3 HT lt gt HT COPY Uploads all of the files sys tem parameters and calen dar clock data stored in the BHT to another BHT This function enables copy ing between the BHTs At the receiving BHT select 2 DOWNLOAD and 2 HT lt gt HT COPY in System Mode For the preparation to be made preceding the start
40. To select a desired item in System Mode press the corresponding numerical key and then press the ENT key The keys below are so designed that the function of each key is consistent in every screen Numerical keys Pressing a numerical key corresponding with a desired menu number selects the desired item displayed on the screen ENT key Pressing this key registers the selected item and executes the corresponding function Miand M2 keys Pressing the M1 or M2 key moves the cursor up or down respectively to select a desired item SF M1 and SF M2 Pressing the M1 or M2 key with the SF key held down keys moves the cursor to the left or right respectively to select a desired setting The C key is inoperative on the SYSTEM MENU On other screens pressing the C key returns to the immediately preceding screen The power on default is EXEC PROGRAM which is highlighted Once any other item is selected the selected item will become highlighted with the cursor when you turn back to the SYSTEM MENU 39 E Structure of System Mode SYSTEM MENU L EXEC PROGRAM DOWNLOAD Land ENT keys 2 and ENT keys Cke y 3 and ENT keys 4 and ENT keys SYSTEM MENU lt Press the PW key while holding down the EXECUTE PROGRAM ISAMPLEQ1_ PD3 SAMPLE 2 PD3 SAMPLE22 PD3 DOWNLOAD aT 2 HT lt gt HT COPY UPLOAD LONE FILE 2 ALL FILES 3 HT lt gt HT COPY
41. add a 0 zero preceding the data NOTE For the year be sure to enter the last two digits of the year For the hour enter it in the 24 hour format If any of the year month day hour and minute is not entered the ENT key will be deactivated If you make a wrong entry press the BS key to delete it and then enter the correct data To return to the SET SYSTEM menu press the C key Example To set 2000 April 19 at 4 00 p m Press 0 0 0 4 1 9 1 6 0 and 0 Press the ENT key to register the above setting 57 4 4 Setting the special scanning parameters BHT 100Q SET QRCODE a INVERT ON 2 DECODE LEVEL x 3 MARKER x 4 VIEW FINDER on Oa S OPTION DATA ON Oia MINIMUM DIGITS G ITF xx 7 CODABAR xx Selecting 4 QRCODE on the SET SYSTEM menu calls up the screen shown at left Highlighted is the current setting 1 INVERT Activates or deactivates the black and white inverted la bel reading function 2 DECODE LEVEL Not applicable 3 MARKER Sets the marker ON OFF mode 4 VIEW FINDER Turns the view finder on or off 5 OPTION DATA Selects whether or not op tion data will be added to the tail of 2D code data read 6 ITF Sets the minimum number of digits to be read for ITF 7 CODABAR Sets the minimum number of digits to be read for Codabar Select a desired item by using the numerical keys or M1 and
42. confirmation screen Selecting a file to be deleted and then pressing the ENT key calls up the confirmation screen shown at left DELETE FILE XXXXXXXX XXX 1 Yes Deletes the selected file Delete 2 No 2 No Cancels deletion and returns to the pre vious file deletion menu Select a desired item by using the numerical keys then press the ENT key 93 DELETE FILE XXXXXXXX XXX Working y Deletion completion screen DELETE FILE Completed When deletion is in progress the screen shown at left is displayed Upon completion of deletion the screen shown at left appears Press the C key to return to the file deletion menu 94 Chapter 2 Getting Started the BHT and System Mode 8 Downloading Uploading the BHT System Parameter File The BHT system parameter file named __BHT SYS stores system environment settings specified in the SET SYSTEM menu in Subsection 2 5 3 4 and other settings such as the LCD contrast and beeper volume The SYSTEM PARAMETER transfer menu allows you to upload or download the BHT system parameter file to from the host computer This helps you make the same settings for the BHTs as those made in a single BHT First make settings in a particular BHT and upload the BHT system parameter file to the host computer by using this menu 2 UPLOAD Next let other BHTs download the file from the host computer by using this menu
43. functions of the keys may be set by user programs Shown below is a set of sample functions Status Indicators Battery voltage level Shows the current battery voltage level Displays when the voltage level is high Displays when the voltage level is low Keypad shift state Displays when the keypad is shifted Alphabet and touch screen input states Displays when the alphabet input function is activated Displays when the touch screen is ready to accept entry M1 M2 Magic keys Up and down arrow keys are assigned to the M1 and M2 keys by default respectively If the SF key is held down left and right arrow keys are assigned to the M1 and M2 keys respectively These keys may be used as an SF key ENT key or backlight function on off key depending upon definition in Sys tem Mode or in user programs They may be also assigned string data in user programs ENT Enter key Finalizes the inputted data or opera tions and starts the corresponding processing Numerical keys Used for numerical input BS Backspace key Moves back one charact r C Clear key PW Power key lear Clears the last inputted data or Turns the BHT Ob ofi returns to the original screen SF Shift key Used in combination with numerical keys for special input procedures Function keys F1 through F8 may be assigned to FUNC
44. in the memory Re fer to Subsection 2 5 3 7 E Problem Uploading has failed E Solution To retry uploading press the 1 key Pressing the 2 key returns to the SYSTEM MENU Check the interface port communications param eters and communications protocol type in the SET SYSTEM menu or perform the communica tions test in the TEST menu Refer to Subsection 2 5 3 4 5 and 5 5 It is also necessary to check the communications parameters setup of the host computer 100 Chapter 2 Getting Started the BHT and System Mode 9 Setting the Remote Wakeup SET REMOTE WAKE UP a REMOTE WAKE UP ON 2 TRANSMIT SPEED EKA 19200 38400 5S7600 115200 Pressing the 4 key while holding down the SF key on the SYSTEM MENU calls up the screen shown at left 1 REMOTE WAKEUP Activates or deactivates the remote wakeup func tion N TRANSMIT SPEED Sets the transmission speed for the remote wakeup Select a desired item by using the numerical keys or M1 and M2 keys Then select a desired setting by using the SF M1 and SF M2 keys To return to the SYSTEM MENU press the C key 101 10 Downloading Uploading the System Message File The system message file named _SYSMSG FN2 stores system messages e g Shutdown in progress Do not remove the battery and Charge the battery The SYSTEM MESSAGE transfer menu allows you to upload or download the system message file to from th
45. it externally adds start and stop bits to the leading and trailing bit positions of the character to be transmitted respectively A clock starts counting on receiving the start bit and it falls into a non communication state on receiving the stop bit The number of the stop bits is selectable 1 or 2 bits E Transmission Speed Maximum number of bits to be transmitted per second Expressed in bps bits per second E Optical Interface Communications Range The optical interface s maximum effective range is 80 cm 31 5 in with the IR beam within a 10 angle of divergence E Switching Time between Sending and Receiving on Optical Interface The optical interface should satisfy the following requirements in switching be tween sending and receiving 1 Within 10 ms from completion of sending the optical interface should become ready to receive 2 After 10 ms or more from completion of receiving the optical interface should start sending 113 E Transmission Code and Bit Order All characters should be coded to 7 or 8 bit code for data transmission The standard data exchange code of the BHT is J IS 7 or 8 bit code The transmission bit order is LSB Least significant bit first What follows is an example for transmitting character A 41h 01000001b coded to J IS 8 level code with an even parity and a single bit each for start and stop bits LSB MSB 1 0 i 0 0 0 0 1 0 0 Start bit Stop bit Parity bit
46. left Press the C key to return to the TEST DISPLAY menu 89 5 7 Key entry beeper and vibrator test TEST KEY amp BEEPER Selecting 7 KEY amp VIBRATION on the TEST menu amp VIBRATION calls up the screen shown at left and makes the BHT ready for entry from the keypad Pressing individual keys displays the identifier let ters in the positions pre assigned to those keys on the LCD as well as sounding the beeper or running the vibrator As long as the individual key is held down the BHT continues beeping or vibrating Pressing the same key again erases the displayed letter The table below shows the relationship between the keys the identifier letters to be displayed on the LCD and the frequencies Hz of the beeper Key Letter Beeper Hz Key Letter Beeper Hz M3 F Note 1 1 698 M1 D 293 2 2 783 M2 E 329 3 3 880 M4 G Note 0 0 987 7 7 391 F 1046 8 8 440 ENT 1174 9 9 493 BS A 1318 4 4 523 C B 1396 5 5 587 SF C 1567 6 6 659 Note Only when the M3 left hand trigger switch or M4 key right hand trigger switch is pressed the vibrator works TEST KEY amp BEEPER After all keys are pressed and displayed on the LCD this test automatically ends and the screen returns to the TEST menu FDEG 7894561230 To stop this test turn the power off ABC 90 5 8 File test TEST FILE SAMPLEO2 PD3 SAMPLEO3 PD3 SAMPLEO4 PD3 SAMPLE S PD3 SAMPLEOG PD3 SAMPLE 7
47. port communications param eters and communications protocol type in the SET SYSTEM menu or perform the communica tions test in the TEST menu Refer to Chapter 2 Subsection 2 5 3 4 5 and 5 5 It is also necessary to check the communications parameters setup of the host computer 136 DOWNLOAD FILE KKK KKK MK KKK File error Retry GEESE 2 No UPLOAD FILE XXXXXXXX XXX File error Upload 2 No Out of memory Chapter 4 Error Messages E Problem You attempted to download an invalid program file E Solution Check whether the program file you attempted to download is available to your BHT model If it is not available download the appropriate program During uploading of a program file data file BHT system parameter file or sys tem message file E Problem The file you attempted to upload is damaged E Solution To upload the damaged file as is press the 1 key E Problem The memory is insufficient for setting up the BHT system parameter file or system message file to be uploaded E Solution Press the C key to return to the SYSTEM MENU and delete unnecessary files Refer to Chapter 2 Subsection 2 5 3 7 137 Too many files UPLOAD FILE MK KKK KKK KKK Communication error Retry 2 No UPLOAD __BHT SYS Communication error Retry MSZE 2 No E Problem The memory has already contained 80 files so the
48. the SYSTEM MENU screen then download user programs Refer to Chapter 2 Subsection 2 5 3 2 UPLOAD FILE E Problem You attempted to select ONE FILE or ALL FILES for uploading in the UPLOAD menu but no data files had been stored in the memory E Solution Press the C key to return to the SYSTEM MENU screen 134 DELETE FILE DOWNLOAD FILE XXXXXXXX XXX Out of memory Retry MSZT 2 No DOWNLOAD FILE XXXXXXXX XXX File mismatch Retry MSZT 2 No Chapter 4 Error Messages E Problem You have deleted all of the files stored in the memory in the DELETE FILE menu E Solution Press the C key to return to the SYSTEM MENU screen During downloading of a program file data file BHT system parameter file or system message file E Problem The memory is insufficient for storing files to be downloaded E Solution Press the 2 key to return to the SYSTEM MENU then delete unnecessary files in the memory or decrease the size of the file to be downloaded Refer to Chapter 2 Subsection 2 5 3 7 2 8 and 10 E Problem In the DOWNLOAD menu you attempted to download the BHT system parameter file or sys tem message file In the SYSTEM PARAMETER transfer menu you attempted to download a file other than the BHT system parameter file Or in the SYSTEM MESSAGE transfer menu you at tempted to download a file other than the system message file E
49. the eyes The light emitted through the reading window is harmful to the eyes Do not poke at the eyes with the stylus that comes with the BHT Handling the CU If smoke abnormal odors or noises come from the CU immediately unplug the AC adapter from the wall socket and contact your nearest dealer Failure to do so could cause fire or electrical shock If foreign material or water gets into the CU immediately unplug the AC adapter from the wall socket and contact your nearest dealer Failure to do so could cause fire or electrical shock If you drop the CU so as to damage its housing immediately unplug the AC adapter from the wall socket and contact your nearest dealer Failure to do so could cause fire or electrical shock Never use the CU for charging anything other than the specified rechargeable battery cartridges Doing so could cause heat battery rupture or fire Never bring any metals into contact with the output terminals Doing so could produce a large current through the CU resulting in heat or fire as well as damage to the CU Use the dedicated AC adapter only Failure to do so could result in fire Never use the CU on the line voltage other than the specified level Doing so could cause the CU to break or burn If the power cord of the AC adapter is damaged e g exposed or broken lead wires stop using it and contact your nearest dealer A A A Q Q Failure to do
50. the numerical keys or M1 and M2 keys and then select a desired setting by using the SF M1 and SF M2 keys To increase the decode level press the SF HM2 keys to decrease it press the SF M1 keys To increase the number of digits to be read for ITF STF and Codabar press the SF HM2 keys to de crease it press the SF M1 keys Press the ENT key To return to the SET SYSTEM menu press the C key Black and white inverted label reading function INVERT This function makes it possible to read white bars on a black background NOTE Activating this function might increase the frequency of bar code reading errors This function can usually be set to OFF DECODE LEVEL You may set the decode level Decreasing the level value increases the bar code reading efficiency but the BHT might misread low quality bar codes split or stained To the contrary increasing the level value decreases the bar code reading efficiency but it will diminish the possibility of misreading The setting range of the level value is from 1 to 9 and the default is 4 61 Marker You may select the marker ON OFF mode from the following 0 Driven by the trigger switch 1 Fixed to ON 2 Fixed to OFF NOTE If you select 1 Fixed to ON the markers will keep ON so that power consump tion is higher than that in other modes and the battery working time becomes short Do not disturb this setting unless necessary Minimum number of digits to b
51. the uploading operation is in progress the screen shown at left is displayed indicating the file name and the number of sent records the total number of records To abort the uploading operation press the C key The screen will switch back to the SYSTEM MES SAGE transfer menu 105 UPLOAD Upon completion of uploading the BHT displays the screen shown at left and beeps once SYSMSG FN3 Completed Press the C key to return to the SYSTEM MES SAGE transfer menu NOTE When the BHT uploads the system message file it creates a temporary file named _SYSMSG FN3 in the user area If the user area is insufficient for creating the tem porary file therefore an error will result The created temporary file will be automati cally deleted after completion of uploading If an error occurs during uploading If some error occurs during uploading one of the following screens will appear and the beeper beeps three times To retry the uploading operation press the 1 and ENT keys to abort it press the 2 and ENT keys Press the C key to return to the SYSTEM MESSAGE transfer menu UPLOAD E Problem _SYSMSG FN3 The file you attempted to upload is broken File error a Solution Upload 2 No To upload the broken file as is press the 1 key 106 Out of memory UPLOAD Too many filtes UPLOAD SYSMSG FN3 Communication errori Retry MEZA 2 No Chapter 2 Ge
52. to send 6 DR Data set ready 7 SG Signal ground 8 CD Carrier detect 20 ER Data terminal equipment ready NOIE Shown below is a diagram of the internal connection in the CU 7000 Host computer modem or i other devices CU 7000 l i Signal Pin No i Name l Optical Interface FG C1 Not used l SD 2 RS 232C Optical l G Interface Ll Communications eres oe ircui Interface RD G Circuitry Circuitry l A l i wa l i cs C5 l ad l i ER 20 o CB l i SG TD l i 162 Appendices Appendix B Communications Protocol Details B 1 BHT protocol 1 Transmission Control Sequences Shown below is a typical message transmission sequence supported by the BHT protocol This sequence example does not include transmission errors or negative responses Sending Receiving Station Station Establishment of h EN Data Link A Q gt Phase 1 lt ACK S EJB pO Heading text T C gt H XIC i lt ACK E B T Serial number Data text 1 T C gt X XC lt ACK Data Transmission Phase 2 i i E B i T Serial number Data text n 1 TCI gt i X XC lt ACK E B T Serial number Data text n io gt X XC i ACK W lt C Release of Data A Link EOT gt Phase 3 i Y lt ACK 163 Data transmission may accidentally involve various types of errors The BHT protocol
53. vibrator You may choose any of three ways beeping only vibrating only or beeping amp vibrat ing as a confirmation of completion of code reading 1 Use the 2 key or M1 or M2 key to select the BEEPER VIBRATION line that will be highlighted in any one of the following three states SF M2 SF M2 wwe VIBRATION BEEPERMVIBRATION BEEPER M R YARON SF M1 SF M1 2 Highlight the desired way s by using the M1 or M2 key while holding down the SF key Adjusting the beeper volume You can adjust the beeper volume to four levels from OFF to MAX 1 Use the 3 key or M1 or M2 key to select the BEEPER VOLUME line 2 To turn down the volume press the M1 key with the SF key held down to turn it up press the M2 key with the SF key held down Adjusting the beeper volume to be sounded when you press the touch screen You can adjust the volume of the beeper to be sounded when you press the touch screen to three levels from OFF to MAX 1 Use the 4 key or M1 or M2 key to select the VOLUME line 2 To turn down the volume press the M1 key with the SF key held down to turn it up press the M2 key with the SF key held down 25 Adjusting the touch screen At the first use of the touch screen or if the touch areas seem to deviate from the nor mal positions when in use adjust the touch screen according to the steps given below CALIBRATION Use the 5 key or M1 or M2 key to selec
54. 0 Appendices E Phase 3 with iterated transmission of DLE EOT and IDs due to no re sponse or invalid response If the sending station receives no response or any invalid response from the receiving station in response to the sent sequence of DLE EOT and IDs it iterates sending of the sequence at 0 5 second intervals up to 60 times If the sending station receives a sequence of DLE ACK and IDs before sending the sequence of DLE EOT and IDs 60 times it terminates the message transmission normally and releases the data link Sending DLE EOT and IDs 1 Receiving station station 0 5 second _ DLE EOT and IDs 2 DLE ACK and IDs Normal termination E Abnormal termination of phase 3 If the sending station receives no sequence of DLE ACK and IDs from the receiving station within 0 5 second from the 60th sequence of DLE EOT and IDs it aborts the message transmission abnormally and releases the data link Sending DLE EOT and IDs 1 Receiving station eee ree stanon 0 5 second DLE EOT and IDs rear pone DLE EOT and IDs 60 0 5 second Abnormal termination 181 E Phase 3 with timeout at the receiving station If the receiving station receives no subsequent text or normal sequence of DLE EOT and IDs within 30 seconds after sending a sequence of DLE ACK and IDs it sends a sequence of DLE EOT and IDs and aborts the transmission abnormally Sending Recei
55. 66 67 69 70 110 116 122 124 125 126 143 173 174 183 BHT protocol 14 63 69 116 118 119 120 143 163 164 172 black and white inverted label reading 54 58 61 188 C C 700 C 750 v 22 calendar clock 16 20 23 29 30 33 38 40 47 51 54 57 130 133 150 157 character length 63 66 113 115 Codabar NW 7 54 58 60 61 62 77 78 152 154 158 Code 128 77 78 152 158 Code 39 77 78 152 158 159 Code 93 78 158 communications LED 140 communications parameter 40 50 53 54 63 64 65 66 95 98 100 102 105 107 115 136 138 143 communications protocol ii 50 53 63 64 65 66 67 69 95 98 100 102 105 107 108 110 116 136 138 143 163 17 47 186 187 control character 116 117 118 119 122 123 124 125 CRC 122 125 183 CU 7001 v x 22 140 144 145 161 CU 7002 140 161 connector cover D Data Matrix DCE 147 60 77 151 154 58 61 16 34 42 43 93 142 decode level deleting files DIP switch direct connect 13 14 17 47 63 64 66 68 81 83 111 112 113 115 122 155 160 download 12 13 15 16 34 38 40 42 45 46 47 48 49 50 51 68 69 95 96 97 98 102 103 104 105 133 134 135 136 137 143 171 177 182 driver iv 15 dry battery cartridge viii 17 19 20 21 31 129 130 149 156 Dsub 25P 142 DTE 147 E EAN 13 77 78 152 158 159 EAN 8 77 78 152 154 15
56. 8 Error in System Mode settings 132 execution program 33 40 54 55 132 133 134 12 15 extension library extension program F field space space codes in the tail of a data fie 63 65 67 filetest 41 91 flash memory 123 133 149 156 177 FUNC 18 40 71 73 G graphics pad box 7 85 89 H hand strap 1 6 7 17 horizontal parity 63 65 67 116 172 HT lt gt HT COPY 47 49 51 52 53 189 Index I indicator LED 2 4 17 41 75 76 78 85 86 144 145 150 157 10 109 infrared communication 16 35 56 interface cable 10 12 13 47 111 112 113 142 147 186 interface port 10 12 13 17 40 47 50 53 54 63 64 68 81 82 83 95 98 100 102 105 107 111 115 136 138 140 142 143 146 162 Interleaved 20f5 ITF 77 78 152 158 ii 108 109 110 Ir Transfer Utility C iii 12 13 14 16 48 49 52 69 143 Ir Transfer Utility E iii 12 13 14 16 48 49 52 69 143 10 12 13 IrDA compliant 10 13 109 110 ITF 54 58 60 61 62 77 78 152 156 158 159 initializing IR communication IrDA interface J J IS Level 1 J IS Level 2 15 16 92 K key entry beeper and vibrator test 75 90 41 keypad shift state 18 L 24 25 38 56 95 LCD contrast LCD indicator LED and touch screen tests 75 85 LED indicators 140 144 149 156 21 129 130 lithium ion battery low b
57. DE Upon completion of bar code reading the BHT Ais 100B beeps turns on the indicator LED in green 4999999999999 and displays the read data together with the bar code type and the number of data digits To return to the TEST menu press the C key Data Listed below is a table showing the relationship between the bar code types and the identifier letters to be displayed on the LCD Bar code Type ID Letters EAN 13 UPC A A EAN 8 B UPC E C Standard 2of5 STF H Interleaved 2of5 ITF l Codabar NW 7 N Code 39 M Code 93 L Code 128 EAN 128 W The minimum number of digits to be read depends on the scanning parameter setting Refer to 4 4 78 5 2 Memory test TEST MEMORY Testing XXXXX YYYYY TEST MEMORY r Test NG x XXXXX YYYYY Address zzzzzzzz write aaaaaaaa Read bbbbbbbb TEST MEMORY w Test OK YYYYYZYYYYY Chapter 2 Getting Started the BHT and System Mode Selecting 2 M EM ORY on the TEST menu calls up the screen shown at left and then starts writing and reading onto from all areas of the RAM as well as checking the address XXXXX Tested RAM capacity in kilobytes YYYYY Total RAM capacity in kilobytes If any error is detected the BHT beeps three times shows the message as shown at left and termi nates the test Where zzzzzzzz Address where an error has occurred aaaaaaaa Data to write bbbbbbbb Data read out from t
58. DENSO BHT 100Q 100B User s Manual Copyright DENSO 2001 All rights reserved No part of this publication may be reproduced in any form or by any means without permission in writing from the publisher Specifications are subject to change without prior notice All products and company names mentioned in this manual are trademarks or regis tered trademarks of their respective holders Preface Please READ through these operating instructions carefully It will enable you to operate your BHT 100Q 100B correctly After you have finished reading the instructions keep this manual handy for speedy reference How this book is organized This manual is made up of five chapters and appendices Chapter 1 Quick Guide Describes the basic operating method of the BHT and the related notes Chapter 2 Getting Started the BHT and System Mode Summarizes the BHT system configuration and describes the operation including preparation and System Mode which is required for the efficient use of application programs Chapter 3 Communications Operations of BHT Describes the communications operations of the BHT the IR communication RS 232C interface specifications basic communications specifications and the communi cations protocols for data transfer with the host computer or other devices Chapter 4 Error Messages Lists the error messages which will appear on the LCD if some error occurs in the BHT Chapter 5 Handling the
59. ET PARAMETER lt OPTICAL gt 1 TRANSMIT SPEED 2400 2968 19200 38400 57600 115200 Selecting 1 PARAMETER on the SET OPTICAL screen calls up the screen shown at left Highlighted is the current setting Select the desired transmission speed by using the numerical keys or SF M1 and SF M2 keys and then press the ENT key To return to the SET OPTICAL screen press the C key 2 Communications protocol option screen SET PROTOCOL lt OPTICAL gt GN OFF 2 H PARITY GN OFF 3 LINKUP TIME None 62 90 120 4 FIELD SPACE Data Selecting 2 PROTOCOL on the SET OPTICAL screen calls up the screen shown at left Highlighted is the current setting 1 SERIAL No Selects whether or not the system will add serial num bers to data blocks 2 H PARITY Selects whether or not the system will add a horizontal parity 3 LINKUP TIME Selects the timeout length in seconds to be applied when a link is to be established 4 FIELD SPACE Selects whether space codes in the tail of a data field will be ignored or handled as data Select a desired item by using the numerical keys or M1 and M2 keys Then select a desired setting by using the SF HM1 and SF M2 keys To return to the SET OPTICAL screen press the C key NOTE If the BHT Ir protocol has been selected the serial number and horizontal parity settings will be ignored 65 4 5 2
60. Freedom from the codes regulations and licenses which differ from country to country unlike radio devices The BHT may communicate with other IrDA compliant equipment just by aligning their IR ports with each other The effective IR range and IR port angle may differ depending upon the target equipment so observe the instructions given in manuals furnished with such equipment NOTE If IR transfer fails bring the BHT closer to the target station or change the IR port __angle and try again 109 The BHT s IR communications device is IrDA compliant IrDA stands for Infrared Data Association which has defined hardware IrDA Serial Infrared Physical Layer Link and communications protocols for IR communications The BHT s physical layer complies with the IrDA1 0 with a maximum transfer distance of 0 8 m and maximum transmission rate of 115 2 kbits per second The BHT adopts the exclusive BHT Ir protocol which allows you to develop user programs for IR communications in BHT BASIC as can be done with conventional wire communications User programs i BHT BASIC i BHT Ir protocol i Physical layer IrDA 1 0 110 Chapter 3 Communications Operations of the BHT 100Q 100B 3 2 RS 232C Interface Specifications 1 Interface Connector and Pin Assignment The BHT has a direct connect interface port which is connectable to the 3 pole mini stereo plug 2 5 mm or 0 1 and supports a su
61. LE OS PD3 SAMPLE OG PD3 SAMPLEO 7 PD3 SAMPLE 8 PD3 SAMPLE 9S PD3 SAMPLE10 PD3 SAMPLE11 PD3 SAMPLE12 PD3 SAMPLE13 PD3 SAMPLE14 PD3 SAMPLE15 PD3 SAMPLE16 PD3 SAMPLE17 PD3 SAMPLE18 PD3 SAMPLE19 PD3 SAMPLE20 PD3 SAMPLE21 PD3 SAMPLE22 PD3 SAMPLE23 PD3 SAMPLE24 PD3 SAMPLE2S PD3 ISAMPLE26 PD3 EXECUTE PROGRAM De SHE HE ake SHE He Se ie ate ee ate oe te ote NO FILE EXISTS ee k gt k In the example shown at left 26 programs are downloaded If no program file is downloaded the message shown at left will appear To return to the SYSTEM MENU press the C key 46 Chapter 2 Getting Started the BHT and System Mode 2 Downloading NOTE If you download a file having the same name as one already used in the user area of the target memory in the BHT the newly downloaded file replaces the old one DOWNLOAD Selecting 2 DOWNLOAD on the SYSTEM MENU calls up the screen shown at left 2 HT lt gt HT COPY 1 FILE Downloads a user program file or data file to the user area of the BHT HT lt gt HT COPY Downloads all of the files system parameters and cal endar clock data stored in the connected BHT N This function enables copy ing between the BHTs For the preparation to be made preceding the start of this function refer to NOTE below Select a desired item by using the numerical keys or M1 and M2 keys and the selected item be comes highlighted
62. SIC refer to the BHT BASIC Programmer s Manual BHT 100 series Vertical parity gt gt b7 i t Character Horizontal parity byte For 8 bit data BCO bO Shown below is a data text block indicating the bits to be added for horizontal parity checking S EIB T aA r Data text T C X xX C lt To be added for gt horizontal parity checking 172 Appendices B 2 BHT Ir protocol 1 Transmission Control Sequences Shown below is a typical message transmission sequence supported by the BHT Ir protocol This sequence example does not include transmission errors or negative responses Sending Station Receiving Station Establishment DLE ENQ and IDm gt of Data Link lt DLE ACK and IDs Phase 1 V i D S D EJC i L O Heading text L T R gt E H D E x c lt DLE ACK and IDs 1D S11 serial D E C KT p number Data text 1 a i gt i lt DLE ACK and IDs Data Transmis sion Phase 2 i D S Serial D EJC i LeT Le TJR ETE number Data text n 1 Bea _ gt lt DLE ACK and IDs D sji De Balie fe ke eT Serial Data text n L T R gt E x pDp number E x c y lt DLE ACK and IDs A Release of Data DLE EOT and IDs gt LiniRhase
63. Solution Check the file you attempted to download and then download the file in the appropriate menu DOWNLOAD menu SYSTEM PARAMETER trans fer menu or SYSTEM MESSAGE transfer menu 135 DOWNLOAD FILE KKK KKK KK KKK Too many files Retry MZT 2 No DOWNLOAD FILE XXXXXXXX XXX Communication error Retry MEZA gt No DOWNLOAD __BHT SYS Communication errort t Retry MEZA 2 No E Problem The current download will exceed the maximum of 80 files in the memory E Solution Press the 2 key to return to the SYSTEM MENU then delete unnecessary files in the memory or decrease the number of files to be downloaded if you attempted to download more than one file in the DOWNLOAD menu Refer to Chapter 2 Subsection 2 5 3 7 2 8 and 10 E Problem Downloading has failed E Solution To retry downloading press the 1 key Pressing the 2 key returns to the SYSTEM MENU Check the interface port communications param eters and communications protocol type in the SET SYSTEM menu or perform the communica tions test in the TEST menu Refer to Chapter 2 Subsection 2 5 3 4 5 and 5 5 It is also necessary to check the communications parameters setup of the host computer E Problem Downloading the BHT system parameter file has failed E Solution To retry downloading press the 1 key Pressing the 2 key returns to the SYSTEM MENU Check the interface
64. T SYSTEM 1 EXEC PROGRAM 2 DISPLAY 3 DATE TIME 4 QRCODE Is COM 6 KEY 7 RESUME C key ENT key SET COM 1 OPTICAL 2 CONNECTOR 5 COM PORT 4 PROTOCOL TYPE C key li ENT key SET COM PORT 1 BASTC BHT 100B SYSTEM MENU L EXEC PROGRAM 2 DOWNLOAD 3 UPLOAD 4 SET SYSTEM S TEST 6 VERSION li ENT key SET SYSTEM 1 EXEC PROGRAM 2 DISPLAY 3 DATE TIME 4 BARCODE IS COM 6 KEY 7 RESUME C key il ENT key SET COM 1 OPTICAL 2 CONNECTOR 3 COM_PORT 4 PROTOCOL TYPE C key ENT key C key 43 SET COM PORT i BASIC onnector onnector C key 2 Selecting a desired setting First select a desired item on the current screen by using the numerical key or the M1 and M2 keys so as to highlight the desired item Next while holding down the SF key use the M1 and M2 keys to select a desired setting and then press the ENT key The screen returns to the previous selection screen onnector onnector onnector 2 SYSTEM MODE aL SET COM 1 OPTICAL 2 CONNECTOR 3 COM PORTI 4 PROTOCOL TYPE 44 Press 2 key or use M1 and M2 keys to select the desired set item Use the SF M1 and SF M2 keys to select the desired setting ENT key Chapter 2 Getting Started the BHT and System Mode 2 5 3 Detailed Description of the Functions in S
65. T in dusty areas therefore periodically check the clear plate of the reading window and clean it if dusty e To clean the plate first blow the dust away with an air brush Then wipe the plate with a cotton swab or the similar soft one gently e If sand or hard particles have accumulated never rub the plate doing so will scratch or damage it Blow the particles away with an air brush or a soft brush FCC Regulations This Device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation NOTE This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Opera tion of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense FCC WARNING Changes or modifications not expressly approved by the party re sponsible for
66. T so that the laser light comes to almost the center of the bar code height IIluminates in green when the BHT has successfully read the code e The BHT can read bar codes at a maximum distance of 40 cm 15 7 from the reading window For details about the scanning conditions refer to Appendix A e The bar code reading procedure may differ depending upon the application used so follow the application s manual Chapter 1 Quick Guide Before reading bar codes clean those labels if stained Avoid using the BHT in direct sunlight The BHT might fail to read correctly To read bar codes on curved surfaces apply the BHT to the target bar code so that the code comes to the center of the scanning range indicated by the laser beam When you pull the bar code reading window away from bar codes the actual scanning range will become narrower than the range covered by the laser beam Do not use the BHT in the vicinity of personal or amateur radio equipment The BHT may malfunction The light intensity of the laser light or illumination LED will vary depending upon the scanning conditions and variation of their elements 1 2 Setting and Using the Hand Strap and Stylus E Setting the hand strap E Using the hand strap Put your hand through the hand strap and hold the BHT as shown below This will prevent you from dropping the BHT accidentally Hand strap Chapter 1 Quick Guide E Setting the stylus Hand strap
67. Then press the ENT key To return to the SYSTEM MENU press the C key NOTE Carrying out 2 HT lt gt HT COPY will not copy the JIS1 and JIS2 font files Those font files may be downloaded by 1 FILE NOTE Preparation for Copying between the BHTs Before downloading to the BHT from another BHT make the following prepa ration e At each BHT set the interface port The default is an optical interface Optical Interface setting procedure Starting on the SYSTEM MENU select 4 SET SYSTEM 5 COM and 3 COM PORT On the SET COM PORT screen select the optical interface Optical or direct connect interface Connector of 2 SYSTEM MODE e When using the direct connect interface pull out the connector cover on each BHT to expose the direct connect interface port Connect the BHTs via those ports with the direct connect interface cable having 3 pole mini stereo plugs For the details about the cable refer to Chapter 3 Section 3 2 On the uploading BHT run System Mode and select 3 UPLOAD and 3 HT lt gt HT COPY 47 Download screens DOWNLOAD FILE Waiting DOWNLOAD FILE KKK KKK KK KKK Loading YYYYYZZZZZZ DOWNLOAD FILE XXXXXXXX XXX Now Checking YYYYYZZZZZZ With this screen displayed the BHT waits for a file to be downloaded If you select 2 HT lt gt HT on the DOWNLOAD menu the HT lt gt HT will appear in the center of the 2nd line If you sel
68. X and DLE ETX are text control characters as described in 2 Control Characters 2 An ID denotes the ID number of the receiver station expressed by two bytes A serial number is expressed by a five digit decimal number starting from 00001 to 32767 and identifies data texts For the CRC 16 refer to Appendix B B 2 BHT Ir protocol 3 TIP You can use the control characters for expressing IDs serial numbers or text data 125 4 Text Format Text should be formatted according to the standard of the BHT Ir protocol before transmission Shown below are two types of the standard text formats for program files and data files E Program Text Format 1 Heading text Byte position 123 4 5 6 7 8 9 10 11 12 13 14 15 16 17 Program file name Number of data texts contained 12 bytes 5 bytes Example of contents P ROG 1 P EF 003 52 l l The program file name should If the program file nameis The number of data texts be a maximum of 12 characters less than 12 characters in should be 0 to 32767 If it in length and it consists of FILE length the lower blank is less than 5 digits the NAME and EXTENSION The bytes will be filled with upper blank bytes will be FILE NAME should be 1 to 8 space characters filled with zeros 0 characters The EXTENSION should be PD3 EX3 and FN3 may be available for future functional expansion 2 Data text 128 or 130 Byte positi
69. a y lt DLE ACK and IDs IDm ID of sending station IDs ID of receiving station 173 Data transmission may accidentally involve various types of errors The BHT Ir proto col is designed to recover from those errors as frequently as possible What follows is the BHT Ir protocol for phases 1 through 3 Phase 1 Establishment of Data Link E Normal phase 1 The sending station transmits a sequence of DLE ENQ and IDm sending station s ID to the receiving station Upon receipt of a sequence of DLE ACK and IDs receiving station s ID from the receiving station the sending station shifts to phase 2 DLE ENQ and IDm TE Sending station Receiving station DLE ACK and IDs To phase 2 E Phase 1 with iterated transmission of DLE ENQ and IDm due to no re sponse or invalid response If the sending station receives no response or any invalid response from the receiving station in response to the sent sequence of DLE ENQ and IDm it iterates sending of the sequence at 0 5 second intervals up to 60 times If the sending station receives a sequence of DLE ACK and IDs before sending the sequence of DLE ENQ and IDm 60 times it shifts to phase 2 Sandin Receiving station a aa i 0 5 second DLE ENQ and IDm 0 5 second eae ore aa ee DLE ACK and IDs To phase 2 oT TIP You may modify the number of iterations of a sequence of DLE ENQ and IDm
70. above errors occurs the BHT beeps five times for 0 1 second per beep and then turns itself off E Solution Turn on the power again If error 1 above occurs frequently contact your nearest dealer If error 2 occurs frequently initialize the BHT System the whole user area including the font file area If error 3 occurs frequently delete the execution program file that causes this error or download the original execution program file to overwrite the current one 133 4 2 Errors in System Mode If some error occurs during operation in System Mode one of the following error messages will appear on the LCD When selecting a program file or data file EXECUTE PROGRAM _ Problem You attempted to execute a user program in the BH ake ake ak k k fe ke ate ae ke ate ote ie ote oe NO FILE EXISTS EXECUTE PROGRAM menu but no user program Be ake ie ak k oe k ie ote ake oe k k oe oe oe files had been stored in the memory E Solution Press the C key to return to the SYSTEM MENU screen then download user programs Refer to Chapter 2 Subsection 2 5 3 2 SET EXEC PROGRAM E Problem In the SET SYSTEM menu you attempted to select NO FILE EXISTS a user program file as an execution program to be ake ake ake ake ake ake ale gt k gt e OR ER OK run when the power is applied but no user pro gram files had been stored in the memory E Solution Press the C key to return to
71. ards Standards Conditions Remarks Noise Standards VCCI A Class B FCC Part 15 A Class A EMC Directive A Class B EN55024 1998 IEC 61000 4 2 1995 IEC 61000 4 3 1995 IEC 61000 4 4 1995 IEC 61000 4 5 1995 IEC 61000 4 6 1996 IEC 61000 4 8 1993 IEC 61000 4 11 1995 EN55022 1995 EMC Framework B Class B AS NZD 3548 Conditions A Meets this standard Approvement pending B Meets this standard C Does not meet this standard D Unknown 185 D 2 Interface Cables With the interface cables described in this section DENSO WAVE has run the quality assurance test conforming to the EMC Directive for the BHT 100Q 100B series and CU 7001 Any connectors other than those specified here are not acceptable They may cause the BHT or CU to fail to work according to the specifications For BHT 100 rom 1000 mmt Si as iad wwii ee Cable 1 Wind the cable on a ferrite core twice and then secure the core with a heat shrinkable tube Connector P161 Teisin Electric Co Ltd D sub connector DLI F T N series EMI durable J apan Aviation Electronics Industry Ltd Connector cover 17 E series hood cable clamp DDK Ltd shielded Cable Super flex VVC 7 0 18 mm x3C Bando Densen Co Ltd Ferrite core ZCAT2035 0930A TDK Corporation Heat shrinkable tube Note A square Q in the above specifications denotes a numeral that will vary according to t
72. are error codes which have the following meanings X the sent data 2 A timeout has occurred during X 1 The received data is different from standby for data reception 1 2400 bps 2 9600 bps 3 115200 bps Press the C key to return to the MASTER SLAVE selection menu The master BHT will automatically return to the MASTER SLAVE selection menu after 10 seconds from the occurrence of an error 82 Chapter 2 Getting Started the BHT and System Mode TEST COM Upon normal completion of the test the tested lt OPTICAL gt slave BHT beeps once and shows the screen at left e Test OK Press the C key to return to the TEST COM menu The master BHT will automatically return to the MASTER SLAVE selection menu Testing the direct connect interface port ERS Or Selecting the 2 CONNECTOR on the TEST COM a menu displays the screen shown at left and then starts testing the direct connect interface port Testing TEST COM If any error occurs the BHT beeps three times and lt CONNECTOR gt shows the screen at left ie ese NE In parentheses are error codes which have the cxx gt following meanings X X 1 The received data is different from the sent data 2 A timeout has occurred during standby for data reception 1 300 bps 2 115200 bps 83 TEST COM Upon normal completion of the test the BHT beeps lt CONNECTOR gt once and shows the screen at left TE TERT O
73. ations LED green Lights when the BHT is communicating with the host computer POWER Power LED green Lights when the power is Og applied to the CU 7000 Optical interface port _f Ay Used to exchange data optically with the BHT BHT charge terminals Not provided on CU 7002 Do not stain these terminals failure to protect the terminals may result in decreased charging efficiency CU 7000 RS 232C interface port Used to exchange data with the host computer Power inlet connector Plug the AC adapter into this connector 140 Chapter 5 Handling the CU 7000 Option 5 3 Applying Power to the CU 7000 Apply power to the CU 7000 by connecting it to the wall socket via the dedicated AC adapter Connect the outlet plug of the AC adapter to the power inlet connector of the CU 7000 then plug the other end of the AC adapter into the wall socket AC adapter N WARNING N CAUTION If smoke abnormal odors or noises come from the CU immediately unplug the AC adapter from the wall socket and contact your nearest dealer Failure to do so could cause fire or electrical shock If foreign material or water gets into the CU immediately unplug the AC adapter from the wall socket and contact your nearest dealer Failure to do so could cause fire or electrical shock If you drop the CU so as to damage its housing immedi ately unplug the AC adapter from the wall socket and con tact your neares
74. attery indication M M1 M2 M3 M4 18 71 72 18 71 72 2 4 17 71 72 2 4 17 71 72 v 40 54 71 72 149 156 2 3 54 58 59 61 62 117 60 77 151 154 41 92 41 79 36 40 41 54 56 92 152 magic key marker MaxiCode memory size memory test message version multi line code N Nonlock 71 NW 7 77 78 152 158 O Onetime 71 12 162 10 12 optical communications optical communications unit 140 optical interface 17 47 63 64 81 82 113 115 140 143 155 160 162 option data 54 58 59 60 77 P PDF417 60 77 151 154 140 144 40 45 129 power LED program execution 190 protection sheet of the DIP switch 142 protocol 63 64 65 66 67 69 70 118 124 143 164 165 172 174 175 Q QR code 58 59 77 149 151 153 R radio communication xi RAM 75 79 149 156 rechargeable battery cartridge ii v vi vii viii 17 19 20 21 22 29 129 130 139 140 144 release button 17 19 remote wakeup 42 101 resume data 132 resume function 33 40 54 74 132 RS 232C ii 10 12 13 108 111 140 142 146 147 155 160 162 S Scandisk 32 33 34 serial number 63 65 67 119 125 163 172 173 183 space codes in the tail of a data field 65 67 2 4 splitQRcode 77 Standard 2of5 STF 78 158 status indicator 18 20 28 STF 54 61 62 78 158 stop bitlength 66 115 Structured App
75. bars 5 max 1 2 magnification 3 Interface Specifications Optical Interface Synchronization Start stop Input signals RD Output signals SD Transmission speed 115 200 bps max Direct connect Interface Synchronization Start stop Transmission speed 115 200 bps max Signal level Conforms to the RS 232C interface Pin assignment As shown below SD RD GND Signal Input Output Pin No Signal Functions BHT External device 1 SG GND Ground for signals 2 SD Send data gt 3 RD Receive data 160 A 3 CU 7000 1 Product Specifications Power Source Europe U S Australia Power Consumption Dimensions W x L x H Weight Operating Ambient Temperature Operating Humidity Appendices 230 VAC 16 VA 120 VAC 13 VA 10 to 18 VDC 450 mA on 12 VDC 8 VA max 112 x 148 x 84 mm 4 41 x 5 83 x 3 31 inches CU 7001 Approx 230 g Approx 8 11 oz CU 7002 Approx 200 g Approx 7 06 oz OT to 40 C 32F to 104F 20 to 80 with no dew condensation 2 Charging Requirements CU 7001 Charge current Charge time Approx 600 mA Approx 4 hours 161 3 Interface Specifications X O 0000000000 25 J RS 232C Interface Port Dsub 25S on the CU 7000 Signal Input Output Pin No Signal Functions cu 7ooo External 1 FG Frame ground 2 SD Send data gt 3 RD Receive data 4 RS Request to send 5 cs Ready
76. bset of the RS 232C interface as shown below Using a direct connect interface cable having the mini stereo plugs makes it possible to connect the BHT to a host computer or another BHT directly without any routing through the CU 7000 on E e SD RD SG 3 pole Mini Stereo Plug 2 5 mm or 0 1 The poles of the plug are assigned as listed below Signal Name Function Signal Input Output BHT External device SD Send data gt RD Receive data SG Signal ground The input output voltage threshold for the logical valued signal is listed below Logical Value Input Voltage Threshold Output Voltage Threshold RD SD 0 3V min 5V min 1 3V max 5V max NOTE e The direct connect interface port is not designed to stand frequent connecting zs disconnecting Do not plug and unplug basically more than one time a day otherwise the service life of the plug will shorten To connect the BHT to a host computer having no IR port or another BHT frequently use the CU 7000 e Allow the specified signals only to enter the direct connect interface port Entry of other signals will result in a failure or malfunction of the BHT 111 2 Interface Cable Connection Connect the BHT directly to a host computer a modem or a printer with a direct connect interface cable as illustrated below BHT Connector I F Host Computer SD RD SG FG SD RD RS CS DR SG CD ER
77. chargers Never dispose of batteries into a fire When disposing of battery cartridges cover their terminal pins with vinyl tape to prevent short circuit Batteries should be recycled properly Do not throw them in the trash 30 Chapter 2 Getting Started the BHT and System Mode 2 3 6 BHT Turning off Notes 1 Shutdown in progress message When the BHT is turned off by pressing the PW key or by the auto power off feature it displays the following message and starts preparation for shutdown Shutdown in progress Do not remove the battery When the above message is displayed do not remove the battery cartridge If you do so and leave the BHT without a battery cartridge loaded for one hour or more then the error message Contact your administrator Note the error number 2XXX may appear when turning the BHT on at the next time 2 Ifthe BHT is turned off abnormally If the BHT is turned off abnormally and is left without a battery cartridge loaded or with a discharged battery cartridge loaded then unsaved data may be lost Normally turned off refers to turned off with the PW key or by the auto power off feature If the above problem has arisen the following message will appear when you load a fully charged battery cartridge or a dry battery cartridge having new dry cells and turn the BHT on Your terminal was not shut down properly the Last time it was used Unsaved data wa
78. compliance could void the user s authority to operate the equipment Labeling Ay AVOID EXPOSURE LASER LIGHT IS EMITTED FROM THIS APERTURE g CAUTION LASER LIGHT DO NOT STARE INTO BEAM mW MAXIMUM OUTPUT 65 nm LASER CLASS II LASER PRODUCT THIS DEVICE COMPLIES WITH 21 CFR CHAPTER 1 SUBCHAPTER J THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS 1 THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND 2 THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION Only for the BHT 100B xi Content Overviews Preface citet a a a a a ae aara ae eee eh peeves i How this book is organized 2 cccceececcceeeeeeeeeeeeeeeeeeneeeeeeeeaeaaeeeeeeesaaaeeeeeeeseaeaeeeeeeeeeaees ii SAFETY PRECAUTIONS a a nieces i aa aaaea a ae aara eens Ri iv Chapter T Quick Guide aria a a aa eaa a a e eOe E A Ena Eaa earren ase eedah i 1 1 1 Reading 2D Codes and Bar Codes sssssssssisissrsisruristirinsintusintnntintutnntnninnnnnnnnn nnn nna 2 BHT 1000 AEAEE A A eats 2 BH T LOOB pnia aiana aS e A a Aa RE A e T a A a a 4 1 2 Setting and Using the Hand Strap and Stylus ssssssssssresisrrsrsrisirisririsernnsrnrnrnns 6 1 3 Setting the Backlight sssesssssrsresessssasersrasrstarenennsnsrarantntentreratntaeronannntanenonnnnanann nenne 8 T4 Usmgthe Keypad itseni a aE Ai a EA RO EE ERER 9 1 5 Transferring Da
79. consists of FILE length the lower blank is less than 5 digits the NAME and EXTENSION The bytes will be filled with upper blank bytes will be FILE NAME should be 1 to 8 space characters filled with zeros 0 characters The EXTENSION should be PD3 FN3 and EX3 may be available for future functional expansion 128 or 130 128 bytes if extension is PD3 Program data 130 bytes if it is FN3 or EX3 Example of L i i l li 0 0 0 0 0 0 contents Object file compiled from a source If a program data field program file having one of the is less than the extensions PD3 FN3 and EX3 maximum digits in length the lower blank bytes will be filled with zeros 0 120 Chapter 3 Communications Operations of the BHT 100Q 100B E Data Text Format 1 Heading text Number of fields 2 bytes Length of data field 1 Length of 2 bytes data field n 2 bytes aia 123456 ee ror T T T T T T T T T T T T T T T T T Data file name 12 bytes Number of data texts contained 5 bytes i l Example of M A S T E R D A T 0 0 5 9 2 0 6 1 0 contents The data file name should be a maximum of 12 characters in length and it consists of FILE NAME and EXTENSION The FILE NAME should be 1 to 8 characters The EXTENSION should be other than PD3 FN3 and EX3 and it may be omitted together with a period The number of data te
80. data fields is 250 50 x 5 bytes and the number of the character count bytes is 5 Accordingly the total is 255 so you can transfer the file 121 3 4 2 BHT Ir Protocol 1 Overview The BHT Ir protocol is the communications procedure for the serial infrared link which is used to transmit files between the BHT and a host or between the BHTs It adopts the response method using ACK NAK codes The BHT Ir protocol can be used also for communications through the direct connect interface The BHT Ir protocol is composed of a defined set of the control character sequences including the following three phases Phase 1 Establishment of data link The sending station confirms that the receiving station is ready to receive data Phase 2 Data transmission The sending station transmits data to the target receiving station Phase 3 Release of data link The sending station confirms whether or not all of the transmitted data has been correctly received by the receiving station If yes the sending station terminates the data transmission and releases the data link For details about the transmission control sequences and CRC refer to Appendix B B 2 BHT Ir protocol 122 Chapter 3 Communications Operations of the BHT 100Q 100B 2 Control Characters The control characters are classified into two groups transmission control characters and text control characters 1 Transmission control characters The transmission contro
81. digits with auto correction on February 29 for year 1901 to 2099 Reading Confirmation Indicator LED Red amp green beeper and vibrator 157 2 Bar Code Specifications 1 Available Bar Code Types Bar code type Bar dimensions Readable magnification Universal product codes EAN 13 EAN 8 UPC A UPC E EAN 13 with supplemental codes EAN 8 with supplemental codes UPC A with supplemental codes UPC E with supplemental codes 2 digit add on 5 digit add on Interleaved 2of5 ITF Standard 2of5 STF Codabar NW 7 Code 39 Code 93 Code 128 EAN 128 0 26 mm min 10 24 mils min 0 8 min 0 125 mm min 4 92 mils min PCS value 0 75 Reflection intensity difference between white and black bars 0 4 0 15 mm min 5 91 mils min PCS value 0 45 0 15 mm min 5 91 mils min PCS value 0 45 2 Optical Properties Required White bars Reflection intensity Black bars PCS value Reflection intensity 45 min 25 Max 0 45 min 158 3 Bar Code Label Size Appendices Recommended width 10 mm min 0 39 inch min Length Depth of field Distance from bar codes to the reading window Length of labels including margins 400 mm 15 75 inches 380 mm max 14 96 inches max Minimum narrow bar width 1 0 mm min 4 Length 4 Thickness of Bars and Depth of Field Minimum narrow bar width Depth of field 0 125
82. e the memory contents will no longer be backed up so that the message Contact your adminis trator Note the error number XXXX or Set the current date and time may appear on the LCD If you will not be using the BHT for a long time follow the instructions given in Subsection 2 3 5 Battery Replacement Notes e Avoid storing the rechargeable battery cartridge in a hot place The battery capacity may be decreased e Do not touch the charge terminals of the rechargeable battery cartridge or stain those terminals Doing so could result in a charging failure E Battery Voltage Level on the Status Indicator Line The battery voltage level is always displayed on the status indicator line For details refer to Subsection 2 3 4 Battery Voltage Display 20 Chapter 2 Getting Started the BHT and System Mode E Low Battery Indication Low battery indication Level 1 If the battery output voltage drops below a specified lower level limit while the BHT is in operation the BHT displays the following Level 1 message for approx 2 seconds and beeps three times After that it will resume previous regular operation Battery voltage has Lowered The battery recharge or replacement time will come soon If the BHT is driven by the rechargeable battery cartridge recharge or replace it if it is driven by the dry battery cartridge replace the dry cells Low battery indication Level 2 If you continue to use the
83. e batteries to rupture or the battery fluid to leak resulting in a fire or bodily injury Avoid dropping the battery cartridge or letting it undergo any shock or impact Doing so could cause the batteries to break generate heat rupture or burn Never charge the rechargeable battery cartridge where any inflammable gases may be emitted doing so could cause fire A CAUTION Do not use batteries or power sources other than the specified ones doing so could gener ate heat or cause malfunction 19 NOTE Never charge the dry battery cartridge e The BHT has an integrated backup power source which backs up the memory and calendar clock in the BHT when no battery cartridge is loaded or the voltage level of the battery cartridge drops below the specified level The backup power source is automatically charged by the battery cartridge When you first load the battery cartridge after purchase or you load it after leaving the BHT unused for a long time do not remove the battery cartridge for 10 minutes or more after that loading This is for charging the memory backup source integrated in the BHT e Be sure to turn the BHT off before battery replacement Replace the battery cartridge quickly Load a charged battery cartridge within 3 minutes from the removal of the cartridge to avoid data loss After battery replacement turn the BHT on and check its operation e Ifyou leave the BHT with no battery cartridge loaded for a long tim
84. e code scanning may be specified in user programs only For details refer to the BHT BASIC Programmer s Manual BHT 100 series 6 Optical Properties Required White cells white bars Reflection intensity 45 min Black cells black bars Reflection intensity 25 max PCS value 0 45 min 152 Appendices 3 Scanning Performance E Scanning reference position As illustrated at left align the reading window with the center of the label code to be BHT 100Q scanned E Scanning distance and area Scanning distance 0 20 40 60 80 100 120 140 160 180 200 l ll ll ll ll li ll i j 1 1 Scanning reference ee position 90 mm or 3 54 as gt ae a Ss 9 G no ain NS Ta laa on N m m x x xx Px x x x x x xX x Scanning area ON otfnwo t Ox aon Width x height Reading Me SNe Smf Sef as window 0 25 mm 9 8 mils a _0 33 mm 13 0 mils Oona 13 7 tails Cell pitch of QR codes supported within this range Y 0 15 mm 5 9 mils 0 25 mm 9 8 mils 0 33 mm 13 0 mils Module size of bar codes supported within this range QR codes Cell pitch Scanning distance 0 25 mm 9 8 mils 30 to 110 mm 1 2 to 4 3 inches 0 33 mm 13 0 mils 30 to 140 mm 1 2 to 5 5 inches 1 0 50 mm 19 7 mils 30 to 200 mm 1 2 to 7 9 inches PCS value 0 9 min Reflection intensity 85 min for white 1 Under these conditions QR code Model 2 Ver 5 37 x 37 cells Err
85. e conditions Codarbar 10 digit Narrow bar Narrow space 0 25 mm 9 8 mils 7 Under these conditions EAN 8 Module size 0 33 mm 13 0 mils The BHT 100Q may fail to read codes due to specular reflection depending upon the position of the light source scanning angle of the reading window and other condi tions 154 Appendices 4 Interface Specifications Optical Interface Synchronization Start stop Input signals RD Output signals SD Transmission speed 115 200 bps max Direct connect Interface Synchronization Start stop Transmission speed 115 200 bps max Signal level Conforms to the RS 232C interface Pin assignment As shown below SD RD GND Signal Input Output Pin No Signal Functions BHT External device 1 SG GND Ground for signals 2 SD Send data gt 3 RD Receive data 155 A 2 BHT 100B 1 Product Specifications Power Source Main power Dimensions W x L x H Weight Operating Ambient Temperature Operating Humidity Ambient Illuminance Controller Keypad e Rechargeable lithium ion battery cartridge 3 6 VDC or e Dry battery cartridge two alkaline manga nese batteries LR6s 67 x 198 x 29 mm 2 6 x 7 8 x 1 1 inches Approx 280 g Approx 9 9 oz including battery cartridge 5 C to 50 C 23 F to 122 20 to 80 with no dew condensation 500 to 3000 2x Depth of field 30 mm PCS value 0 9 min Reflection intensity 85 min for w
86. e ed EOT 3 seconds C pel wwe Normal termination E Abnormal termination of phase 3 If the sending station receives no ACK from the receiving station within three seconds from the 10th EOT it terminates the message transmission abnormally and releases the data link Sending station 3 seconds Receiving tea station San ee oe 3 seconds 3 seconds or more EOT 10 termination 170 Appendices 2 Aborting Data Transmission Pressing the C key aborts data transmission If the C key is pressed during downloading the BHT transmits an EOT and aborts the file transmission If it is pressed during uploading the BHT transmits the current transmission block followed by EOT and then aborts the file transmission 171 3 BCC for Horizontal Parity Checking To check whether data has been transmitted accurately the BHT supports horizontal parity checking for every transmission block In horizontal parity checking a horizontal parity byte so called BCC Block Check Character is suffixed to an ETX of every transmission block In the BHT protocol every parity bit of BCC is set so that all set bits at the same bit level including a parity bit in the characters contained in the transmission block have an even number by binary addition excluding SOH STX and functions SOH and STX For details about SOH and STX which are protocol functions unique to BHT BA
87. e from 2D codes or bar codes will differ Do not use the BHT in the vicinity of radio equipment The BHT may malfunction At the scanning time the marker LEDs and illumination LED will come on The illumination LED may not come on where it is bright enough for the BHT to scan The light intensity of those LEDs will vary depending upon the scanning conditions and variation of their elements BHT 100B Turn the BHT power on bring the bar code reading window to the bar code to be scanned and press the trigger switch The BHT 100B emits a laser light to indicate the scanning range and turns on the illumination LED to scan the bar code When the BHT has read the bar code successfully the indicator LED will illuminate in green Bar code scanning range covered by the laser light Max 40 cm 15 7 Indicator LED ee Touch screen LCD Trigger switch M3 key Trigger switch M4 key PW key e If the BHT fails to read due to specular effects or other factors change the scanning angle of the reading win dow or the distance from codes as shown at right and try it again Specular effects occur when the reflec tion of the light from the bar code becomes exces sively strong This can easily happen when the re flecting surface is polished or covered with vinyl The laser light indicates the scanning range as a guide The indicated scanning range will deviate a little bit from the actual one Keep the BH
88. e host computer If you select the 2 UPLOAD the system will set up the system message file based on the current settings and upload it to the host computer After that the created file will be deleted If you select the 1 DOWNLOAD the BHT will receive the system message file from the host computer and apply the stored messages After that the received file will be deleted For uploading downloading the BHT will use the communications parameters com munications protocol and interface port specified in Subsection 2 5 3 4 5 Setting the communications environments TIP Usually you do not need to use this SYSTEM MASSAGE transfer menu since system messages have been set at the time of delivery from the factory SYSTEM MESSAGE transfer menu SYSTEM MESSAGE Pressing the 6 key while holding down the SF key on the SYSTEM MENU calls up the screen shown at left 1 DOWNLOAD 2 UPLOAD 1 DOWNLOAD Downloads the system mes sage file to the user area of the BHT N UPLOAD Uploads the system message file stored in the BHT Select a desired item by using the numerical keys or M1 and M2 keys then press the ENT key Press the C key to return to the SYSTEM MENU 102 Chapter 2 Getting Started the BHT and System Mode 10 1 Downloading the system message file DOWNLOAD Waiting 1 DOWNLOAD SYSMSG FN3 Loading YYYYYZZZZZZ DOWNLOAD SYSMSG FN3
89. e read for ITF STF or Codabar You may set the minimum number of digits to be read for ITF STF and Codabar Setting a small number of digits increases the frequency of digit missing reading or misreading depending upon how to scan bar codes or the quality of bar codes On the other hand setting a large number will diminish the possibility of those errors The setting range is from 2 to 20 for ITF from 1 to 20 for STF and from 3 to 20 for Codabar The default is 4 for ITF and Codabar and 2 for STF 62 Chapter 2 Getting Started the BHT and System Mode 4 5 Setting the communications environments After the BHT is initialized the interface port and communications parameters are set as listed in the default table below Do not access them unless necessary Interface port Optical Optical interface port Communications protocol BHT protocol Communications parameters Defaults for the optical interface port TRANSMIT SPEED 9600 bps PROTOCOL SERIAL No ON Adds serial numbers Protocol options to data blocks H PARITY ON Adds a horizontal parity LINKUP TIME 30 seconds FIELD SPACE Ignore Listed below are the default communications parameters for the direct connect inter face Communications parameters for Defaults the direct connect interface port TRANSMIT SPEED 19200 bps PARITY BIT None Vertical parity DATA BIT 8 bits Character length STOP BIT 1 bit PROTOCOL SERIAL No ON Adds s
90. e stored in the memory the message shown at left will appear Pressing the C key returns to the UPLOAD menu If you select 1 ONE FILE and choose a file to be uploaded or if you select the 2 ALL FILES or 3 HT lt SHT COPY on the UPLOAD menu then the screen shown at left will appear If you select 2 ALL FILES or 3 HT lt gt HT COPY the ALL or HT lt gt HT will appear in the center of the 2nd line respectively Showing this screen the BHT waits for a file s to be uploaded Upon start of optional Ir Transfer Utility C lr Trans fer Utility E Transfer Utility or equivalent program upon receipt of an ACK code from the host com puter the BHT displays the file name and the number of sent records the total number of records on the screen as shown at left To abort the uploading operation press the C key The screen will switch back to the UPLOAD menu Refer to the Ir Transfer Utility C Guide Ir Trans fer Utility E Guide Transfer Utility Guide 52 Chapter 2 Getting Started the BHT and System Mode UPLOAD FILE Upon completion of uploading the number of sent records becomes equal to the total number of MRK KKK MM KKK tine Sen ses Reich ei records and the beeper beeps once Press the C key to return to the UPLOAD menu If you have selected 2 ALL FILES or 3 HT lt SHT COPY on the UPLOAD menu a sequence of the above screens will be repeated by the number of files to be uploaded If an
91. e to the last transmission block data text n the sending station shifts to phase 3 If a transmission message contains no data text the sending station transmits the heading text only Sending station To phase 3 Heading text DLE ACK and IDs Data text 1 DLE ACK and IDs I I I I Data text n 1 DLE ACK and IDs Data text n DLE ACK and IDs Receiving station 176 Appendices E Phase 2 with suspension of data reception for erasure of the flash memory If the receiving BHT requires the flash memory to be erased for receiving downloaded files it sends a sequence of WACK and IDs to the sending station to suspend the data transmission Upon receipt of the sequence of WACK and IDs the sending station stops the data transmission until any response comes from the receiving station for one minute If no response comes within one minute the sending station sends a sequence of DLE EOT and IDs and then aborts the current transmission Sending Heading text Receiving station station WACK and ID Start of erasure DLE ACK and IDs lt End of erasure Data text 1 177 E Phase 2 with a sequence of DLE NAK and IDs If the sending station receives a sequence of DLE NAK and IDs from the receiving station in response to a transmission block containing text data m it sends that transmission block again immediately as shown below If the sending
92. ect 1 FILE nothing will ap pear on the 2nd line The screen at left shows that 1 FILE has been se lected Upon start of optional Ir Transfer Utility C Ir Trans fer Utility E Transfer Utility or equivalent program upon receipt of an ENQ code from the host com puter the BHT displays the file name and the number of received records the total number of records on the screen as shown at left To abort the downloading operation press the C key The screen will switch back to the DOWNLOAD menu Refer to the Ir Transfer Utility C Guide Ir Trans fer Utility E Guide Transfer Utility Guide 48 DOWNLOAD FILE XXXXXXXX XXX Completed Chapter 2 Getting Started the BHT and System Mode Upon completion of downloading the number of received records becomes equal to the total number of records and the beeper beeps once Press the C key to return to the DOWNLOAD menu If the host computer downloads another new file if the BHT receives an ENQ code when this screen is displayed the BHT starts receiving it Refer to the Ir Transfer Utility C Guide Ir Trans fer Utility E Guide Transfer Utility Guide If you have selected 2 HT lt gt HT COPY on the DOWNLOAD menu a sequence of the above screens will be repeated by the number of files to be downloaded If an error occurs during downloading If some error occurs during downloading the BHT beeps three times and shows one of the following sc
93. ed selected F1 F2 F3 F4 F1 F2 F3 F4 TIP Even if enabled in the above setting these function keys will not work in System Mode e If the screen scrolls no function keys will move 73 4 7 Setting the resume function SET RESUME Selecting 7 RESUME on the SET SYSTEM menu calls up the screen shown at left 1 ON 2 0OFF Highlighted is the current setting 1 ON Activates the resume function which resumes the current BHT status when the BHT power was turned off when the BHT is switched on 2 OFF Deactivates the resume function Select a desired item by using the numerical keys or M1 and M2 keys and then press the ENT key To return to the SET SYSTEM menu press the C key 74 5 Testing BHT 100Q TEST 2 MEMORY 3 BEEPER AGING 7 COM 7 DISPLAY KEY amp VIBRATION o VN Ow sh FILE BHT 100B TEST a BARCODE MEMORY BEEPER AGING 7 DISPLAY 7 KEY amp VIBRATION z 3 4 5 COM 6 T 8 FILE Chapter 2 Getting Started the BHT and System Mode Selecting 5 TEST on the SYSTEM MENU calls up the screen shown at left 1 QRCODE BARCODE BHT 100B BEEPER AGING COM jor A W IN LCD BHT 100Q MEMORY Selects the 2D code amp bar code reading test Selects the bar code readin
94. ed as normal data in the transmission texts 117 2 Text control characters The text control characters are used to format transmission texts In the BHT protocol they include the following headers and a terminator Symbol Value Meaning Function SOH olh Start Of Heading Indicates the start of heading text Phase 2 STX 02h Start of Text Indicates the start of data text Phase 2 ETX 03h End of Text Indicates the end of data text Phase 2 You may designate values of headers and a terminator with the protocol functions in BHT BASIC If you designate none of them in a user program the BHT may apply those as listed above Refer to the BHT BASIC Programmer s Manual BHT 100 series 118 Chapter 3 Communications Operations of the BHT 100Q 100B 3 Basic Format of Transmission Messages Basically the BHT transmits data as units of a file First it transmits a heading text which includes the attribute information of a file e g file name and the number of data texts to be transmitted Following the heading text it transmits the data text in the file A heading text and data text comprise a text In actual text transmission the text is divided into several blocks then a header and terminator are added to each block If the serial number management or error checking by BCC Block Check Character is required the serial number or BCC is also added to each block respectively This procedure forms a transmission bl
95. eeeceeeeeeeeteeeeteeeenesneeneetnetietiees 24 2 3 4 Battery Voltage Display cecceceeeeceeeeeeeceneeeeeseeeeseessaeeeeseeeesieteesetneesaeeaes 28 2 3 5 Battery Replacement Notes a 29 2 3 6 BHT Turning off Notes eese ae os 1 Shutdown in progress message naL 2 Ifthe BHT is turned off abnormally sssssssssssrssisssisrrsrsrsrisrrsrsrnrienisrsren 31 3 sABOut S BRKLST SY SS isecetsisicescceesevesss sesssicscvececececevcaaieist vorvivreetitiasesctedes 34 4 If invalid files are found oo ccc ccccsseccesssseseccsrecseeseeesseeeeeessueseuseeeeeseaeess 34 2 4 Initiali ng the BHT SySteM oee ee sass ses eunrerners ta ceased cuaenieies ievavsanduvcemerenmaciicranteneeneats 35 2 5 Operating in System Mode ccicccccescccceccsceceeeeeesscccecdeussevseesnvescvbareverneeveraccedeedoceeeseeede 39 Dede Stating System Mode sarerea aaaeeeaa aan PERAE AET Enea Aaaah E iiA 39 2 5 2 Operating in System Mode ssssssssssssssisisrsrsssitisisrinrutisrnstutannsinnnntanntunnnnnnnn nent 43 1 Calling up the desired set screen ssssssssiersssirierisrsinisirsrerinierinrernn 43 2 Selecting a desired setting esssssssesssrsrrsseisrssrsrurirnsrnrunnnnnsinnunnnnsnsnnnna 44 2 5 3 Detailed Description of the Functions in System Mode sesser 45 1 Program Execution 2 Downloadi Ginna ann nanna aa a de A B oloto NI aTe EEEE A A EE EA 4 System Environment Setting essssssssesssisrisisinrierisrsinnisrisrnrnnn neissen na 54 EEA OS ae EA T
96. ells width 1 2 gt m n Example If a code read is Data M atrix Error correction level ECC200 10 cells wide by 10 cells high then the option data below will follow Data read Z0200010010 Minimum number of digits to be read for ITF or Codabar You may set the minimum number of digits to be read for ITF and Codabar Setting a small number of digits increases the frequency of digit missing reading or misreading depending upon how to scan bar codes or the quality of bar codes On the other hand setting a large number will diminish the possibility of those errors The setting range is from 2 to 20 for ITF and from 3 to 20 for Codabar The default is 4 for ITF and Codabar 60 Chapter 2 Getting Started the BHT and System Mode BHT 100B SET BARCODE Selecting 4 BARCODE on the SET SYSTEM menu as calls up the screen shown at left a DECOBE LEVEI 3 Highlighted is the current setting 3 MARKER x 2 SENTU exes 1 INVERT Activates or deactivates the fos ee Le black and white inverted la egies oe bel reading function DER AEE 2 DECODE LEVEL Sets the decode level 3 MARKER Sets the marker ON OFF mode 4 ITF Sets the minimum number of digits to be read for ITF 5 STF Sets the minimum number of digits to be read for STF 6 CODABAR Sets the minimum number of digits to be read for Codabar Select a desired item by using
97. end 77 vi viii 1 6 7 17 26 85 89 specular effect stylus supplemental code 158 synchronization 113 155 160 system area 15 133 41 92 system message file 42 49 102 103 104 105 106 107 135 137 138 System Mode ii xv 11 15 16 18 34 39 40 42 43 45 47 51 59 68 69 73 81 85 115 129 130 132 134 143 164 165 174 175 183 42 49 95 96 system down error system information system parameter file 97 98 99 100 135 136 137 138 System Program malfunction 131 system program version 41 92 T 65 67 82 83 165 175 182 2 4 24 25 26 27 85 timeout touch screen 89 150 Transfer Utility iii 12 13 14 16 48 49 52 69 121 143 transmission speed 14 65 66 101 109 113 115 142 155 160 117 123 trigger switch 2 4 8 17 24 59 62 71 72 77 90 184 transparency U UPC A 77 78 152 158 UPC E 77 78 152 158 upload 16 34 40 42 47 51 52 53 68 69 91 95 98 99 100 102 104 105 106 107 134 137 138 143 171 182 user area 102 103 106 133 15 16 35 36 37 45 47 95 Index Vv vertical parity 63 66 113 114 115 172 view finder 2 54 58 59 W wireless 109 191 BHT 100Q 100B User s Manual First Edition February 2001 Second Edition October 2001 DENSO WAVE INCORPORATED The purpose of this manual is to provide accurate information in the hand
98. er to the CU 7000 sssssssssssssisrsssssisrsrnsintanisrnnnnnnnnsrnnnnnnnnnnnnnnnnn nnna 141 5 4 Communicating with the Host COMPUtEr s s ssssssssssssssisisisinnriersrnrnnnneiernsinnninrnna 142 5 4 1 Setting the Transmission Speed of the CU 7000 sesser 142 5 4 2 Interface Cable CONNECHION wo cececeteeeneseeeerscesieeeseserseseteensasensaesnnees 142 5 4 3 Interfacing with the Host Computer wie 143 5 5 Charging the Rechargeable Battery Cartridge using the CU 7001 144 5 6 RS 232C Interface Specifications 0 eee ceeeeeeeteeee tere eeeeneteeeseeenesneeenetneeseeeea 146 1 Interface Connector and Pin ASSIQGNMENE eeeeeeeeeeeeeeeteeeteeeetteeeneeaee 146 2 Interface Cable CONNECtION ceccccccesseceecsssesescsseeceeseeeeseeeresensteeessreneeeseaes 147 Chapter 5 Handling the CU 7000 Option 139 5 1 Functions of the CU 7000 The optical communications unit CU 7000 is available in two models CU 7001 and CU 7002 The CU 7001 has both of functions 1 and 2 given below the CU 7002 has only function 1 1 Data exchange function The CU 7001 CU 7002 exchanges data and programs between the BHT and the host computer It interfaces with the BHT via the optical interface and with the host computer via the RS 232C interface 2 Battery cartridge charging function The CU 7001 charges the rechargeable battery cartridge loaded in the BHT 5 2 Components and Functions LED indicators DATA Communic
99. erial numbers Protocol options to data blocks H PARITY ON Adds a horizontal parity LINKUP TIME 30 seconds FIELD SPACE Ignore 63 SET COM Selecting the 5 COM on the SET SYSTEM menu calls up the screen shown at left 2 CONNECTOR ISCON PORT 1 OPTICAL Switches to the communi 4 PROTOCOL TYPE cations parameters setting screen for the optical inter face 2 CONNECTOR Switches to the communi cations parameters setting screen for the direct con nect interface 3 COM PORT Switches to the interface port setting screen 4 PROTOCOL TYPE Switches to the communi cations protocol type set ting screen Select a desired screen by using the numerical keys or M1 and M2 keys and then press the ENT key To return to the SET SYSTEM menu press the C key 4 5 1 Setting the communications parameters for the optical interface e OP nECAL Selecting 1 0PTICAL on the SET COM menu calls up the screen shown at left 2 PROTOCOL 1 PARAMETER Switches to the commu nications parameters set ting screen 2 PROTOCOL Switches to the commu nications protocol option screen Select a desired screen by using the numerical keys or M1 and M2 keys and then press the ENT key To return to the SET COM menu press the C key 64 Chapter 2 Getting Started the BHT and System Mode 1 Communications parameters setting screen S
100. error occurs during uploading If some error occurs during uploading one of the following screens will appear and the beeper beeps three times To retry the uploading operation press the Land ENT keys to abort it press the 2 and ENT keys UPLOAD FILE E Problem POET OE The file you attempted to upload is damaged File error Upload E Solution 2 No To upload the damaged file as is press the 1 key UPLOAD FILE E Problem XXXXXXXX XXX Uploading has failed Communication error t Retry MSZA 2 No E Solution To retry uploading press the 1 key Pressing the 2 key returns to the SYSTEM MENU Check the interface port communications param eters and communications protocol type in the SET SYSTEM menu or perform the communica tions test in the TEST menu Refer to Subsection 2 5 3 4 5 and 5 5 It is also necessary to check the communications parameters setup of the host computer 53 4 System Environment Setting BHT 100Q SET SYSTEM 1 EXEC PROGRAM 2 DISPLAY 3 DATEYTIME QRCODE 4 5 G 7 BHT 100B Selecting 4 SET SYSTEM on the SYSTEM MENU calls up the screen shown at left 1 EXEC PROGRAM 2 DISPLAY SET SYSTEM a4 EXEC PROGRAM 3 DATE TIME 4 QRCODE BHT 100Q BARCODE BHT 100B 5 COM 6 KEY 7 RESUME Sets an execution program to be run when the power i
101. f Depending upon the battery level the beeper may not sound five times E Solution If the BHT is loaded with the rechargeable battery cartridge replace or charge it For the charging procedure refer to Chapter 5 Section 5 5 If the BHT is loaded with the dry battery cartridge replace the dry cells Calendar clock stopped E Problem The calendar clock integrated in the BHT has stopped because The battery cartridge had been removed for a long time The rechargeable battery cartridge had not been recharged for a long time or The dry cells in the dry battery cartridge had not been replaced NOTE The indication of 00 01 01 00 00 will vary depending upon the calendar clock state E Solution Set the calender clock refer to Chapter 2 Subsec tion 2 3 2 130 Your terminal was not shut down properly the Last time it was used Unsaved data was Lost CSF 2 9 Reload the battery to restart Reload the battery to restart tskid XXXXXXXX ercd XXXXXXXX addr IXXXXXXXX o2 Chapter 4 Error Messages Abnormally turned off last E Problem After turned off abnormally the BHT had been left with no battery cartridge loaded or with a dis charged battery cartridge loaded so unsaved data was lost Normally turned off refers to turned off with the PW key or by the auto power off feature E Solution Refer to Subsection 2 3 6 BHT Turning off Notes
102. forthe sending station The default is 60 times at 0 5 second intervals For details refer to the SET PROTOCOL screen in System Mode pp 65 and 67 and the XFILE statement given in BHT BASIC Programmer s Manual BHT 100 series 174 Appendices E Abnormal termination of phase 1 Abort of phase 1 If the sending station receives no sequence of DLE ACK and IDs from the receiving station after sending a sequence of DLE ENQ and IDm 60 times in succession it sends a sequence of DLE EOT and IDm to the receiving station after 0 5 second from the 60th sequence of DLE ENQ and IDm then aborts the message transmis sion abnormally Sending Receiving station station DLE ENQ and Dm 1 0 5 second DLE ENQ and IDm 2 0 5 second ier ore i i 1 i DLE ENQ and IDm 60 0 5 second Pel Abnormal termination TIP The receiving station s default timeout is 30 seconds You may modify the timeout length on the SET PROTOCOL screen in System Mode pp 65 and 67 or by using the XFILE statement refer to the BHT BASIC Programmer s Manual BHT 100 series 175 Phase 2 Data Transmission E Normal phase 2 The sending station first sends a transmission block containing the heading text Each time the sending station receives a sequence of DLE ACK and IDs from the receiving station it sends a transmission block containing the data texts as shown below Upon receipt of a sequence of DLE ACK and IDs in respons
103. g Data Transmission sccscccccisciscestvenvedestiitiin heeseesatineeneveivnnste ite 182 3 CRC 4 Appendix C A Typical Basic Operation ssssssssssssresisissisissrsintuirsrnrnnnnnisinnnnnnnnnnnnnnn annaa Appendix D Quality Assurance Standards D 1 Applicable Standards D2 Mterface Cables aee e a a ATE e Appendices 148 Appendix A Specifications A 1 BHT 100Q Appendices 1 Product Specifications Power Source Main power Dimensions W x L x H Weight Operating Ambient Temperature Operating Humidity Ambient IIluminance Controller Keypad e Rechargeable lithium ion battery cartridge 3 6 VDC or Dry battery cartridge two alkaline manga nese batteries LR6s 67 x 198 x 29 mm 2 6 x 7 8 x 1 1 inches Approx 280 g Approx 9 9 oz including battery cartridge 5 C to 50 C 23 F to 122 20 to 80 with no dew condensation 20 to 10000 2x Depth of field 90 mm QR code Ver 5 37 x 37 cells Error correction level M Cell pitch 0 5 mm PCS value 0 9 min Reflection intensity 85 min for white 500 to 3000 2x Under the conditions except the above CPU 32 bit RISC RAM 1MB Flash memory 8MB Trigger switches M3 M4 2 Magic keys M1 M2 2 Numerical keys and others 16 149 Display Type Touch screen dot matrix FSTN liquid crystal display LCD with backlight Formation Character display 200 dots wide by 304 dots high Status display
104. g test Selects the RAM read write test Selects the beeper scale test Selects the aging test Selects the communications test Selects the LCD indicator LED and touch screen tests 7 KEY amp VIBRATION 8 FILE Selects the key entry beeper and vibrator tests Selects the file checksum test Select a desired setting by using the numerical keys or M1 and M2 keys and then press the ENT key The selected test will start Highlighted is the currently selected item To return to the SYSTEM MENU press the C key NOTE If an error occurs in any of the above tests contact your nearest dealer 75 5 1 2D code and bar code reading test BHT 100Q TEST QRCODE y Sample 1 Number of digits of the code Code type TEST Qerc oE Q 8001 0066 1234567890123456 7890123456789012 3456789012345678 9012345678901234 56 Data read Sample 2 Code type TEST QRCODE Q xxxx OL 1234567890ABCDEF GHIJKLMNOPQRSTUV WXYZ1234567890AB CDEFGHIJIKLMNOPQR STUVWXYZ12345678 SO ABCDEFGHIIKLMN OPQRSTUVWXY2Z1234 56789 ABCDEFGHII KLMNOPQRSTUVWXYZ 1234567 890ABCDEF GHIJIKLMNOPQRSTUV WXYZ1234567890AB CDEFGHIJKLMNOPQR STUVWXYZ12345678 S ABCDEFGHIJIKLMN OPQRSTUVWXY2Z1234 56789 ABCDEFGHIJI KLMNOPQRSTUVWXYZ 1234567890ABCDEF GHIJIKLMNOPQRSTUV WXYZ1234567890AB CDEFGHTJIKLMNOPQR Selecting 1 QRCODE on the TEST menu calls up the screen shown at left Actually read bar code
105. ge or dry bat tery cartridge and contact your nearest dealer Failure to do so could cause smoke or fire For those machines using the dry battery cartridge do not mistake the plus and minus marks when loading dry cells into the cartridge Failure to do so could cause battery rupture or leakage of battery fluid resulting in bodily injury fire or property damage For those machines using the dry battery cartridge do not use any thing other than the specified type of batteries nor use new and old batteries together Doing so could cause battery rupture or leakage of battery fluid resulting in bodily injury fire or property damage Do not use batteries or power sources other than the specified ones doing so could generate heat or cause malfunction In environments where static electricity can build into significant charges e g if you wipe off the resin plate with a dry cloth do not operate the BHT Doing so will result in malfunction or machine failure Touch the LCD only with the stylus that comes with the BHT Using the tip of a pen or any pointed object will result in a damaged or broken LCD Handling the CU e If you will not be using the CU for a long time be sure to unplug the AC adapter from the wall socket for safety Failure to do so could result in a fire e When caring for the CU unplug the AC adapter from the wall socket for safety Failure to do so could result in an electrical shock viii
106. given below 1 When removing the battery cartridge Press the PW key for more than 3 seconds to turn the power off The following message will appear on the LCD and the BHT will start backing up data After completion of the backup operation so that the message disappears remove the battery cartridge The backup operation may take several tens of seconds depending upon the volume of data to be backed up Now saving data Do not remove batteries until saving process complete Shows the current Shows the total volume backup state in of data to be backed up progress 29 2 When turning the BHT on after storage with no battery cartridge loaded Even after removal of the battery cartridge the calendar clock will work with the backup power source for a while If the calendar clock backup has stopped loading the battery cartridge and turning the BHT on will display the following message prompting you to set the current date and time Set the calendar clock according to the procedure given in Subsection 2 3 2 The indication 00 01 01 00 00 will vary depending upon the calendar clock state Set the current date and time O O1 01 88 00 a 7 The rechargeable battery cartridge can be recharged hundreds of times but it will eventually wear out If the run time is noticeably shorter than normal replace the battery cartridge with a new one Use only DENSO WAVE authorized battery cartridges and
107. he RAM To return to the TEST menu press the C key Upon normal completion of the RAM test the BHT beeps once shows the message as shown at left and returns to the TEST menu 79 5 3 5 4 Beeper scale test TEST BEEPER Aging test TEST AGING DATE TIME 7 37 1 15 30 00 Selecting 3 BEEPER on the TEST menu calls up the screen shown at left and makes the beeper sound at three octaves listed below Upon completion of this test the BHT automati cally returns to the TEST menu To stop this test while in progress turn the power off and on Scale Frequency Hz do 523 1046 2093 4186 re 587 1174 2349 mi 659 1318 2637 fa 698 1396 2793 sol 783 1567 3135 la 880 1760 3520 ti 987 1975 3951 a Selecting 4 AGING on the TEST menu proceeds to the aging test while showing the current date and time on the LCD This test is intended for personnel which check the BHT in the factory NOTE Once this test is selected the automatic powering off function becomes disabled Be sure to turn the power off or press the C key to return to the TEST menu 80 Chapter 2 Getting Started the BHT and System Mode 5 5 Communications test In System Mode you may test the optical interface port and direct connect interface port E Preparation for the optical interface test Arrange two BHTs one as a master station and the other as a slave s
108. he SET SYSTEM menu press the C key Defining the function of the shift key SET SHIFT KEY 1 Nonlock 2 0netime Selecting the 1 SHIFT KEY on the SET KEY menu calls up the screen shown at left Highlighted is the current setting 1 Nonlock Shifts the keypad only when the SF key is held down 2 Onetime Shifts only one key pressed im mediately after the SF key is pressed The following keys will not be shifted Select a desired setting by using the numerical keys or M1 and M2 keys and then press the ENT key The screen returns to the SET KEY menu 71 Defining the function of M1 M2 M3 left hand trigger switch or M4 right hand trigger switch key SET M3 KEY Selecting the 2 M1 KEY 3 M2 KEY 4 M3 KEY Inana or 5 M4 KEY on the SET KEY menu calls up the screen as shown at left This example appears OSH rE Kev when the 4 M3 KEY is selected 4 Enter Key Highlighted is the current setting 5 Backlight Key The M1 M2 M3 or M4 key can function as listed below 1 None The key entry will be ig nored 2 Trigger Switch As the trigger switch 3 Shift Key As the SF key 4 Enter Key As the ENT key 5 Backlight Key As the backlight function on off key Select a desired setting by using the numerical keys or M1 and M2 keys and then press the ENT key The screen returns to the SET KEY menu The M3 and M4 key
109. he number of connector pins 186 For CU Cable 2 Appendices D sub connector D sub connector to be connected to CU Connector cover Connector cover Shielded cable 000 Q Ferrite core withstanding EMI DL F T N series EM l durable DB 25SF T N S1 17 E series hood cable clamp shielded 17 E 250 10 RISC 5F J apan Aviation Electronics Industry Ltd J apan Aviation Electronics Industry Ltd DDK Ltd DDK Ltd Kitagawa Industries Co Ltd Note A square L in the above specifications denotes a numeral that will vary according to the number of connector pins A circle O in the above specifications denotes a numeral that will vary accord ing to the hood appearance and the type of connector screws 187 Index Symbols BRKLST SYS 34 2D code and bar code reading test 76 3 pole mini stereo plug 13 47 81 111 A abnormally turned off last 131 AC adapter vi viii ix x 140 141 142 143 144 41 75 80 31 131 aging test auto power off B backlight function on off key 18 72 battery level battery output level battery output voltage battery voltage level 18 20 21 22 28 129 130 BCC 119 172 beeper scale test 75 80 beeper volume 24 25 56 95 BHT turning off notes 31 131 BHT BASIC Compiler 12 13 16 BHT BASIC Extension Library 12 BHT BASIC Interpreter 15 BHT Ir protocol 14 65
110. hich can divide data in a QR code into a maximum of 16 blocks and encode each of them into a split QR code When reading split QR codes the BHT 100Q beeps in a different way from usual That is when the BHT 100Q reads the first split code it beeps twice and enters the split code scanning mode After that each time it reads the subsequent split code it beeps once If the BHT 100Q reads the last split code it beeps three times and completes the sequence of split code scanning The scanned data will not be displayed on the LCD until a sequence of split code scanning is completed If you scan any non split code midway in a sequence of split code scanning the BHT 100Q displays the scanned non split code cancels the split code scanning mode and discards those split codes being scanned The same occurs also if you release the trigger switch or the split code scanning interval exceeds approx 5 seconds The scanning order of split codes is arbitrary The same split code will never be double scanned If the OPTION DATA is set to ON on the SET QRCODE screen in the SET SYSTEM menu see 4 4 Setting the special scanning parameters then the option data will follow QR code data read 77 BHT 100B TEST BARCODE Selecting 1 BARCODE on the TEST menu calls up the screen shown at left Actually read bar codes with the BHT 100B and check the read data displayed on the LCD 1 Bar code type Number of digits of the bar code TEST BARCO
111. hite and 5 max for black Narrow bar width 0 125 mm min 20 to 10000 2x Depth of field 250 mm ITF 1 0 magnifica tion PCS value 0 9 min Reflection intensity 85 min for white and 5 max for black CPU 32 bit RISC RAM 512KB Flash memory 4MB Trigger switches M3 M4 2 Magic keys M1 M2 2 Numerical keys and others 16 156 Appendices Display Type Touch screen dot matrix FSTN liquid crystal display LCD with backlight Formation Character display 200 dots wide by 304 dots high Status display 200 dots wide by 16 dots high Screen mode Font size Dots W x H Chars x Lines Single byte Standard size ANK Normal size 12x 12 16 x 25 ANK mode 12 dot Double width 24x12 8x25 Double height 12 x 24 16 x 12 Quadruple size 24 x 24 8x12 Two byte Standard size Full width Normal size 16x 16 12x19 Kanji mode 16 dot Double width 32x 16 6x19 Double height 16 x 32 12x9 Quadruple size 32 x 32 6x9 Half width Normal size 8x16 25x19 Double width 16 x 16 12x19 Double height 8 x 32 25x9 Quadruple size 16 x 32 12x9 Small size Full width Normal size 12x 12 16 x 25 12 dot Double width 24x12 8x25 Double height 12 x 24 16 x 12 Quadruple size 24 x 24 8x12 Half width Normal size 6x12 33x 25 Double width 12 x 12 16 x 25 Double height 6x 24 33x12 Quadruple size 12 x 24 16x12 ANK Alphanumerics and Katakana Calendar Clock Year month day hour minute and second e Year Two
112. host computer Refer to Subsection 2 5 3 3 Uploading Contents of the BRKLST SYS file Records 1 File name 2 Error factor Broken since the BHT has not been turned off normally Broken due to any other causes 3 Broken records e g 01000 01200 Data in records numbered 1000 to 1200 is lost Example SAMPLE1 DAT 01000 01050 If more than one sequence of records is broken in SAMPLE1 DAT 01200 01250 a same file they will be written into the SAMPLE1 DAT 01600 01650 subsequent records in the BRKLST SYS SAMPLE2 DAT 00250 00275 SAMPLE3 DAT 00100 00150 t t t 1 2 3 4 If invalid files are found Even invalid files may be uploaded so upload them to the host computer according to your needs After uploading Delete those invalid files Refer to Subsection 2 5 3 7 Deleting Files or Download valid files having the same names as invalid files Refer to Subsection 2 5 3 2 Downloading 34 Chapter 2 Getting Started the BHT and System Mode 2 4 Initializing the BHT System Initializing the system will lose program files and data files stored in the user area and the system settings will revert to the factory defaults TIP You may delete font files by selecting the whole user area to be initialized You need to initialize the system when 1 you want to delete all of the program files and data files 2 the following message appears Contact your adm
113. i Press the C key to return to the TEST COM menu 84 Chapter 2 Getting Started the BHT and System Mode 5 6 LCD indicator LED and touch screen tests In System Mode you may test the LCD indicator LED and touch screen TEST DISPLAY pie Tere p 2 TOUCH SCREEN1 3 TOUCH SCREENZ LCD amp indicator LED test BS key f ENT key BS key f A ENT key Selecting 6 LCD on the TEST menu calls up the screen shown at left on the LCD 1 LCD Tests the LCD and indicator LED 2 TOUCH SCREENI Tests touch keys 3 TOUCH SCREEN2 Tests the graphics pad box by drawing an image with the stylus Select a desired item by using the numerical keys or M1 and M2 keys then press the ENT key Selecting 1 LCD on the TEST DISPLAY menu calls up the test pattern shown at left on the LCD and turns on the indicator LED in green Each time the ENT key is pressed the screen shifts to the next test pattern To return to the previous screen press the BS key To stop this test while in progress press the C key As shown at left everything disappear and the indicator LED lights in red 85 The checker pattern shown at left appears and the a ana indicator LED goes off E Pa a a n n a n a annn watatatatatartatatararst Se ee BSkey ff ENTkey The checker pattern is reversed BS key tt ENT key An outl
114. if it has been charged for the specified hours replace the battery cartridge with a new one Generally it is necessary to replace the battery cartridge after it has undergone approx 300 cycles of charging and discharging operation 1 Plug the AC adapter of the CU 7001 into the wall socket The POWER LED on the CU 7001 lights in green 2 Place the BHT loaded with a battery cartridge onto the CU 7001 The BHT turns on the indicator LED in red and starts charging The charging time is approx 4 hours Upon completion of charging the indicator LED turns green BHT CU 7001 3 Take the BHT off the CU 7001 TIP The charging time is approx 4 hours if the Charge the battery message is displayed on the BHT The battery cartridge not discharged so much will be fully recharged in shorter time 144 Chapter 5 Handling the CU 7000 Option E Charging Operation and LED Indication Operator s Action CU 7001 Status Indicator LED on the BHT Place the BHT on the CU 7001 4 After approx 4 hours y Remove the BHT On standby 4 Normal charging Charging completed 4 On standby O O O O OFF ON in red ON in green OFF 145 5 6 RS 232C Interface Specifications 1 Interface Connector and Pin Assignment The CU 7000 has an RS 232C interface port Dsub 25S RS 232C interface port Dsub 25S on the CU 7000 Pin No Signal Functions Signal In
115. ine with a width of one dot appears BS key f ENT key 86 Chapter 2 Getting Started the BHT and System Mode The fine checker pattern appears BS key tt i ENT key The fine checker pattern is reversed BS key f ENT key Forty right angled triangles appear BS key tt i ENT key 87 BS key f ENT key B p ABCDEFGH Riatatet 01234567 RERPRERT 24x12 BS key f ENT key um wee Of Oth ox Sik wi mi ns aN ak ae qh Cth o oka ENE ENE uN aN zak capex ibs ip oom eo OMS OFK uN aN Press the ENT key and the BHT beeps once and returns to the TEST DISPLAY menu BS key f ENT key 88 Touch screen test 1 TOUCH SCREEN Touch screen test 2 TOUCH SCREEN2 Chapter 2 Getting Started the BHT and System Mode Selecting 2 TOUCH SCREEN1 on the TEST DIS PLAY menu calls up the screen shown at left Press individual touch keys 1 on the LCD When each of them is pressed the beeper will sound and the key will become highlighted W Pressing the highlighted key again will cancel highlighting 1 Pressing all five touch keys highlighting all or C key will return to the TEST DISPLAY menu Selecting 3 TOUCH SCREEN2 on the TEST DIS PLAY menu calls up the screen shown at left You may draw an image with the stylus in the box graphics pad box shown at
116. ing station confirms whether or not all of the transmitted data has been correctly received by the receiving station If yes the sending station terminates the data transmission and releases the data link For details about the transmission control sequences and horizontal parity checking refer to Appendix B B 1 BHT protocol 116 Chapter 3 Communications Operations of the BHT 100Q 100B 2 Control Characters The control characters are classified into two groups transmission control characters and text control characters 1 Transmission control characters The transmission control characters listed below are used to compose transmission control sequences in phases 1 through 3 Symbol Value Meaning Function EOT 04h End Of Transmission Releases a data link Phase 3 Requests abort of transmission Phase 2 ENQ 05h Enquiry Requests establishment of a data link Phase 1 Prompts the receiver to respond to the sent text Phase 2 ACK 06h Acknowledge Acknowledgment response to ENQ Phase 1 Acknowledgment response to text Phase 2 Acknowledgment response to EOT Phase 3 NAK 15h Negative Acknowledge Negative acknowledgment response to ENQ Phase 1 Negative acknowledgment response to text Phase 2 E Transparency The BHT uses the non transparent mode which handles the control characters and codes e g STX ETX and SOH as starting or ending markers and does not allow them to be transmitt
117. inistrator Note the error number c2XxXx gt D On the following pages is an initialization procedure 35 1 Selecting the memory area to be initialized INITIALIZE a USER AREA EXCEPT FONTS Area selection screen INITIALIZE 1 USER AREA EXCEPT FONTS 2 WHOLE USER AREA Press the PW key while holding down the SF M1 and Okeys together The screen shown at left will appear To initialize the user area except for the font file area press the ENT key The screen switches to the SELECT MESSAGE display given in step 2 To initialize the whole user area including the font file area press the 2 key while holding down the SF key The 2 WHOLE USER AREA item will appear 1 USER AREA EXCEPT FONTS Initializes the user area except for the font file area 2 WHOLE USER AREA Initializes the whole user area including the font file area TIP If the message Contact your administrator Note the error number 2X XX appears on the LCD you need to select 2 WHOLE USER AREA to initialize the whole user area Select an area to be initialized by using the nu merical keys then press the ENT key The screen switches to the SELECT MESSAGE display given in step 2 2 Selecting the English or J apanese message version SELECT MESSAGE 1 Japanese 2 English Preceding the execution of initialization the mes sage version selection screen will appear as sho
118. itial setting combination of SF and the right hand trigger switch as well as modifying the ON duration of the backlight before the automatic turning off Chapter 1 Quick Guide 1 4 Using the Keypad E Entering Numerical Data To enter numerical data e g the quantity of goods use the ten numerical keys and the ENT key For example to enter the number 120 press the 1 2 and 0 keys and then press the ENT key If you key in any wrong value press the C or BS key and then enter the correct one E Selecting Tasks If the LCD shows the selection items xxx prefixed by numerals e g 1 xxx 2 xxx use the numerical keys to select a desired item and press the ENT key to execute If a YES NO screen e g 1 YES 2 NO appears press the 1 key for YES response and 2 key for NO response E Entering Alphabetic Characters The BHT supports the alphabet entry function which allows you to enter alphabetic characters space and symbols from the keypad during execution of a user program For the alphabet entry procedure refer to the BHT BASIC Programmer s Manual BHT 100 series 1 5 Transferring Data E Using infrared link Using infrared rays the BHT may transfer data directly to the host computer equipped with an IrDA interface port and other IrDA compliant devices NOTE e Make sure that there is no obstruction in the light path between the BHT and any target stations In infrared communication you need to keep the
119. keys defined on the touch screen For details refer to Subsection 2 5 3 4 6 18 Chapter 2 Getting Started the BHT and System Mode 2 3 Preparation 2 3 1 Setting up 1 Loading the Battery Cartridge Before the first use of the BHT be sure to load the battery cartridge as shown below The battery cartridge is not loaded in the BHT when shipped from the factory 1 Charge the rechargeable battery cartridge Refer to Section 5 5 To use the dry battery cartridge in the BHT set two dry cells into the cartridge Refer to the Dry Battery Cartridge User s Manual that comes with the dry battery cartridge NOTE Use the dry battery cartridge as a spare of the rechargeable battery cartridge The run time of the dry battery cartridge loaded with new dry cells is shorter than that of the fully charged rechargeable battery cartridge 2 Turn the BHT upside down 3 As shown below slide the battery cartridge into the BHT until it clicks into place To remove it press the release button after making sure that the BHT power is off Release button A WARNING e Never disassemble or heat the battery cartridge nor put it into fire or water doing so could cause battery rupture or leakage of battery fluid resulting in a fire or bodily injury Do not carry or store the battery cartridge to gether with metallic ball point pens necklaces coins hairpins etc Doing so could short circuit the terminal pins causing th
120. l Communications E Host Computer option option Ir Transfer Utility C option Ir Transfer Utility E option Transfer Utility option Chapter 2 Getting Started the BHT and System Mode E Host Computer Models PC AT PS 2 Optional application programs and OSes OS us bos Win3 1 Win95 Wings WinnT3 5 4 0 Win2000 Applications Professional BHT BASIC Compiler Fae cae Windows BHT BASIC3 5 Ir Transfer Utility C en Win95 NT based Ir Transfer Utility E er a ee a Transfer Utility hee ae e Win95 NT based This application does not activate any built in port E CU 7000 and RS 232C Interface Cable option The CU 7000 is an IrDA compliant communications unit which is required when your host computer is not equipped with an IrDA interface port The CU 7000 exchanges data and programs with the BHT optically and with the host computer via the RS 232C interface cable You may directly connect two BHTs with each other by using a commercially available metal cable having 3 pole mini stereo plugs as a direct connect interface cable You also connect the BHT directly with the host computer or with the modem by using the direct connect interface cable compatible with the target equipment NOTE The direct connect interface port of the BHT is not designed to stand frequent connecting disconnecting You are therefore recommended to
121. l characters listed below are used to compose transmission control sequences in phases 1 through 3 Symbol Value Meaning Function DLE EOT 1004h End Of Transmission Releases a data link Phase 3 Requests abort of transmission Phase 2 DLE ENQ 1005h Enquiry Requests establishment of a data link Phase 1 Prompts the receiver to respond to the sent text Phase 2 DLE ACK 1006h Acknowledge Acknowledgment response to DLE ENQ Phase 1 Acknowledgment response to text Phase 2 Acknowledgment response to DLE EOT Phase 3 DLE NAK 1015h Negative Acknowledge Negative acknowledgment response to DLE ENQ Phase 1 Negative acknowledgment response to text Phase 2 WACK 103Bh Waitfor Acknowledge Requests suspension of data recep tion during erasure of the flash memory E Transparency The BHT uses the transparent mode which allows the control characters and codes e g STX ETX SOH and DLE to be transmitted as normal data in the transmis sion texts To transmit a DLE as normal data type DLE DLE per DLE 123 2 Text control characters The text control characters are used to format transmission texts In the BHT Ir protocol they include the following headers and a terminator Symbol Value Meaning Function DLE SOH 1001h Start Of Heading Indicates the start of heading text Phase 2 DLE STX 1002h Start of Text Indicates the start of data text Phase 2 DLE ETX 1003h End of Text Indica
122. ling and operating of the BHT 100Q 100B Please feel free to send your comments regarding any errors or omissions you may have found or any suggestions you may have for generally improving the manual In no event will DENSO WAVE be liable for any direct or indirect damages resulting from the application of the information in this manual
123. mber of records To abort the uploading operation press the C key The screen will switch back to the SYSTEM PA RAMETER transfer menu 98 Chapter 2 Getting Started the BHT and System Mode UPLOAD Upon completion of uploading the BHT displays the screen shown at left and beeps once BHT SYS t Completed Press the C key to return to the SYSTEM PARAM ETER transfer menu If an error occurs during uploading If some error occurs during uploading one of the following screens will appear and the beeper beeps three times To retry the uploading operation press the 1 and ENT keys to abort it press the 2 and ENT keys Press the C key to return to the SYSTEM PARAMETER transfer menu UPLOAD E Problem __BHT SYS The file you attempted to upload is broken File error E Solution Upload A ee To upload the broken file as is press the 1 key E Problem The memory is insufficient for setting up the BHT system parameter file to be uploaded E Solution Press the C key to return to the SYSTEM MENU then delete unnecessary files in the memory Re fer to Subsection 2 5 3 7 Out of memory 99 Too many files UPLOAD _ _BHT SYS Communication errortlt Retry MEZA 2 No E Problem The memory has already contained 80 files so the BHT system parameter file cannot be set up E Solution Press the C key to return to the SYSTEM MENU then delete unnecessary files
124. mm _ 4 92 mils 0 to 30mm 0 to 1 18 inches 0 15mm 5 91 mils Oto 70mm 0 to 2 76 inches 2 0 33mm 12 99 mils Oto 150 mm 0 to 5 91 inches 1 0 mm 39 37 mils 140 to 350 mm 5 51 to 13 78 inches 1 2mm 47 24 mils 160 to 400 mm 6 30 to 15 75 inches gt 1Under the following conditions Ambient illuminance 500 2x Fluorescent lamp Code 39 19 digit Narrow bar Wide bar 1 2 2 Reflection intensity of white bars 85 min Reflection intensity of black bars 5 max 2Under the following conditions Ambient illuminance 500 2x Fluorescent lamp Code 39 6 digit Narrow bar Wide bar 1 2 2 Reflection intensity of white bars 85 min Reflection intensity of black bars 5 max 3 Under the following conditions Ambient illuminance 500 2x Fluorescent lamp EAN 13 1 0 magnification Reflection intensity of white bars 85 min Reflection intensity of black bars 5 max 4Under the following conditions Ambient illuminance 500 2x Fluorescent lamp ITF conforming to the UPC Shipping Con tainer Code Reflection intensity of white bars 85 min Reflection intensity of black bars 5 max 1 0 magnification 5 Under the following conditions Ambient illuminance 500 2x Fluorescent lamp ITF conforming to the UPC Shipping Con tainer Code Narrow bar Wide bar 1 2 2 Reflection intensity of white bars 85 min Reflection intensity of black
125. mmuni cations test LCD indication test indicator LED test touch screen test key entry test vibrator test and file test Shown at left is the BHT 100Q screen The BHT 100B screen displays 1 BARCODE instead of 1 QRCODE Refer to Subsection 2 5 3 5 System Information Shows the system program version memory size system message version and J IS font type and version Refer to Subsection 2 5 3 6 In addition to the functions given on the previous pages System Mode has these four functions Deleting files Downloading uploading the BHT system parameter file Set ting the remote wakeup parameters and Downloading uploading the system message file To call up these functions press the 0 3 4or 6 key respectively while holding down the SF key when the SYSTEM MENU is displayed SYSTEM MENU EXEC PROGRAM DOWNLOAD Owith SF held down 3 with SF held down 4with SF held down 6 with SF held down SYSTEM MENU lt Press the PW key while holding down the SF DELETE FILE EEEEEEETPEETI XXXXXXXX XXX XXXXXXXX XXX XXXXXKXX XXX XXXXXKKX XXX XXXXXKXK XXX XXXXX KKK XXX XXXXXXXX XXX XXXXXXXX XXX XXXXXXXX XXX XXXXXXXX XXX XXXXXXXX XXX XXXXXXXX XXX XXXXXXXX XXX XXXXXXXX XXX XXXXXXXK XXX XXXXXXXX XXX XXXXXXXX XXX XXXXXXXX XXX SYSTEM PARAMETER 1 DOWNLOAD 2 UPLOAD SET REMOTE WAKE UP L REMOTE WAKE UP ON Oma 2
126. mmunications protocol interface port communications parameters and protocol options Regarding the communications protocol When using Ir Transfer Utility C Ir Transfer Utility E on the host computer select the BHT Ir protocol when using Transfer Utility select the BHT protocol Regarding the interface port Select the optical interface port On the host computer initiate a communications program e g Ir Transfer Utility C lr Transfer Utility E Transfer Utility or equivalent To transfer data stored in the BHT to the host computer select 3 UPLOAD on the SYSTEM MENU in System Mode To transfer data from the host computer to the BHT select 2 DOWNLOAD For details refer to Chapter 2 Section 2 5 The BHT and the host computer will start communications with each other via the CU 7000 The DATA LED will come on upon start of communications After completion of communications the LED will go off Unplug the AC adapter of the CU 7000 from the wall socket 143 5 5 Charging the Rechargeable Bat tery Cartridge using the CU 7001 You may charge a rechargeable battery cartridge loaded in the BHT NOTE Service Life of Rechargeable Battery Cartridge Lithium ion batteries used in the rechargeable battery cartridge will gradually deteriorate during the repeated cycles of charging and discharging due to its properties even under normal use When the battery service period becomes shortened due to its deterioration even
127. n Sending Receiving station station Data text m 3 seconds Ce 3 seconds ee eel a ACK Data text m 168 Appendices E Abnormal termination of phase 2 Abort of phase 2 If the sending station receives no ACK from the receiving station after sending an ENQ nine times in succession it sends an EOT to the receiving station after 3 seconds from the 9th ENQ to terminate this transmission sequence abnormally Sending station 3 seconds ENQ 1 3 seconds pe en 3 seconds peaks Abnormal termination Receiving station Phase 3 Release of Data Link E Normal phase 3 The sending station transmits an EOT to the receiving station Upon receipt of an ACK from the receiving station the sending station terminates the message trans mission normally and releases the data link Sending station EOT ACK Normal termination 169 Receiving station E Phase 3 with iterated EOT transmission due to no response or invalid response If the sending station receives no response or any invalid response from the receiving station in response to an EOT sent it iterates sending of an EOT at three second intervals up to ten times If the sending station receives an ACK before sending an EOT ten times it termi nates the message transmission normally and releases the data link Sending Receiving station EOT station 3 seconds p
128. nications Operations of the BHT 100Q 100B ccs000 108 3 1 Infrared COMMUNICATION 2 0 eee ee eee ete cent eee tete tee eter teat teed tee eneeeaee tae taee tastes tae eaeeaeee 109 3 2 RS 232C Interface Specifications eee cece ee ee ee eee etter teeter teres teste eases enaeeeee 111 3 3 Basic Communications Specifications ANd Parameters ou ceessscsseestecseeseeesaes 113 3 3 1 Basic Communications SPECIFICATIONS 0 eee cte tte tte ete tee eeeete teeter eeeteeetaes 113 3 3 2 Communications Parameters 0 cece cece eee teee tee tete terete teat teeteeeteeeteetneetaeetaee 115 xii 34 Communications Protocols tah vic hin a A Ee A ENT ues E tats 116 oo M R E lE eleonora eed ae 116 342 BHTIr Protocol sa a e ea eed en aa A a a a a a ie 122 Chapter 4 Error Messages cccsssccceseeeeeseeeeseeeeeseneeeenaaeeseeeeesnaeesesaeeeessaeeessaneessaaes 128 4l SYStOMY Errors ns a exten ceed A E EN A a dies 129 4 2 Errors in System MOC eeceeceee eee eeee crete eeeeae ease ee eeeseeseneseesteesneesneeteeseeeteeeae 134 Chapter5 Handling the CU 7000 Option cc ccessseeceseeeeeseeeeeeeeeeeeseeeeesseeeesaees 139 5 1 Functions of the CU 7000 winch a a 140 5 2 Components and FUNCTIONS oo eeceee ee teeee eee eeee cee ttnn eeee tees tees teetaee tastes Ennan Ennan nanna 140 5 3 Applying Power to the CU 7000 0 0 ecceecsee ee seeeceeeteeeeeeteeeeeeteeseesaeeaeeaeenaeeieenaeeas 141 5 4 Communicating with the Hos
129. nterface port to be used for user programs written in BHT BASIC OPEN COM Selects the optical or direct connect interface port to be used for downloading or uploading files in System Mode Select a desired item by using the numerical keys or M1 and M2 keys and then select a desired setting by using the SF M1 and SF M2 keys To return to the SET COM menu press the C key 68 Chapter 2 Getting Started the BHT and System Mode 4 5 4 Setting the communications protocol type PROTOCOL TYPE Selecting the 4 PROTOCOL TYPE on the SET COM menu calls up the screen shown at left 2 BHT IrProtocol Highlighted is the current setting 1 BHT Protocol Selects the BHT protocol for downloading or uploading files in System Mode or for the execution of XFILE state ment in BHT BASIC This protocol should be se lected for file transmission with Transfer Utility 2 BHT Ir Protocol Selects the BHT Ir protocol for downloading or uploading files in System Mode or for the execution of XFILE state ment in BHT BASIC This protocol should be se lected for file transmission with Ir Transfer Utility C Ir Transfer Utility E Select a desired item by using the numerical keys or M1 and M2 keys and then press the ENT key To return to the SET COM menu press the C key 69 SET ID e001 gt gt _ SET ID 01 gt gt 65535_ Selecting the 2 BHT Ir Protocol on the PROTO
130. ock A set of transmission blocks makes up one transmission message Shown below is an example of a transmission message formed with the BHT protocol Text Heading text Data text 1 Data text 2 Data text n S E B O Heading text T C Transmission block H XIC eee S Serial E B noe T number Data text 1 T C Transmission block x 5 bytes x lc S E B Serial ARS 3 mber Data text n Transmission block In the above figure SOH STX and ETX are text control characters as described in 2 Control Characters 2 A serial number is expressed by a five digit decimal number starting from 00001 to 32767 and identifies transmitted data texts For the BCC refer to Appendix B B 1 BHT protocol 3 119 4 Text Format Text should be formatted according to the standard of the BHT protocol before trans mission Shown below are two types of the standard text formats for program files and data files E Program Text Format 1 Heading text Byte position Example of contents 2 Data text Byte position 123 45 67 8 91011 12 13 14 15 16 17 Number of data Program file name texts contained 12 bytes 5 bytes P ROG1 PD 3 1 1 0 03 5 2 l l The program file name should If the program file nameis The number of data texts be a maximum of 12 characters less than 12 characters in should be 0 to 32767 If it in length and it
131. of this function refer to NOTE given on page 47 Select a desired item by using the numerical keys or M1 and M2 keys and the selected item be comes highlighted Then press the ENT key To return to the SYSTEM MENU press the C key NOTE Carrying out 3 HT lt gt HT COPY will not copy the JIS1 and JIS2 font files Those font files may be uploaded by 1 ONE FILE or 2 ALL FILES UPLOAD FILE ISAMPLEQ 1__ PD3 SAMPLE 2 PD3 SAMPLE 3 PD3 SAMPLE 4 PD3 SAMPLE 5 PD3 SAMPLE 6 PD3 SAMPLEO7 PD3 SAMPLE 8 PD3 SAMPLE 9S PD3 SAMPLE1 PD3 SAMPLE11 PD3 SAMPLE12 PD3 SAMPLE13 PD3 SAMPLE14 PD3 SAMPLE15 PD3 SAMPLE16 PD3 SAMPLE17 PD3 SAMPLE18 PD3 SAMPLE19 PD3 SAMPLE20 PD3 If you select 1 ONE FILE on the UPLOAD menu the file selection screen as shown at left will ap pear listing all of the program files and data files stored in the memory Select a file s you want to upload and press the ENT key If you select 2 ALL FILES or 3 HT lt gt HT COPY on the UPLOAD menu the ALL or HT lt gt HT will appear in the center of the 2nd line respectively 51 UPLOAD FILE Die He ake gt k ak oe He k ie ae oe ae oe oe oe DiC gt k ak ak k k k k k ote ie aie ke ae ote Upload screens UPLOAD FILE Waiting UPLOAD FILE KKK KK KKK KKK Loading YYYYYYZZ2Z222Z If you select 1 ONE FILE or 2 ALL FILES on the UPLOAD menu when no files ar
132. on ie s2r a ee ig po a ie eee ae ee Ng Vv T T T T T T T T T T T T T T T T T T T T T T 128 bytes if extension is PD3 Program data 130 bytes if it is EX3 or FN3 Example of i iz 0 0 0 0 0 0 contents I Object file compiled from a source program file having one of the extensions PD3 EX3 and FN3 126 If a program data field is less than the maximum digits in length the lower blank bytes will be filled with zeros 0 Chapter 3 Communications Operations of the BHT 100Q 100B E Data Text Format 1 Heading text Byte Number of fields 2 byt 2 bytes Length of data field 1 Length of 3 bytes data field n contents 3 bytes position 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 T T T T T T T T T T T T T T T t T a T 4 Data file name Number of data a texts contained 12 bytes 5 bytes Example of M AS eb Ry Dy Ah 0 Or by 942 050 2 5 4 Il J l The number of data Every data field texts should be 0 to should be 1 to 254 32767 If itis less than 5 digits in length If itis digits the upper blank less than 3 digits the The data file name should be a bytes will be filled with upper blank bytes will maximum of 12 characters in length zeros 0 be filled with zeros 0 and it consists of FILE NAME and EXTENSION The FILE NAME should be 1 to 8 characters The EXTENSION should be other than PD3 EX3 and FN3 and it may be omit
133. or correction level M Black and white label 2 Under these conditions QR code Model 2 Ver 3 29 x 29 cells Error correction level M Black and white label 153 PDF417 Module size Scanning distance 0 17 mm 6 7 mils 40 to 100 mm 1 6 to 3 9 inches 3 0 25 mm 9 8 mils 40 to 170 mm 1 6 to 6 7 inches 3 0 33 mm 13 0 mils 40 to 200 mm 1 6 to 7 9 inches 3 PCS value 0 9 min Reflection intensity 85 min for white 3 Under these conditions 1 column 11 row Row height 3 modules Error correction level 1 MaxiCode Cell pitch Scanning distance 0 88 mm 34 6 mils 45 to 230 mm 1 8 to 9 1 inches PCS value 0 9 min Reflection intensity 85 min for white Data Matrix Cell pitch Scanning distance 0 25 mm 9 8 mils 30 to 110 mm 1 2 to 4 3 inches 0 33 mm 13 0 mils 30 to 140 mm 1 2 to 5 5 inches 0 55 mm 21 7 mils 30 to 200 mm 1 2 to 7 9 inches PCS value 0 9 min Reflection intensity 85 min for white 4 Under these conditions 36 x 36 cells Error correction level ECC200 Black and white label Bar codes Module size Scanning distance 0 15 mm 5 9 mils 40 to 90 mm 1 6 to 3 5 inches gt 0 25 mm 9 8 mils 40 to 170 mm 1 6 to 6 7 inches 0 33 mm 13 0 mils 40 to 200 mm 1 6 to 7 9 inches 7 PCS value 0 9 min Reflection intensity 85 min for white 5 Under these conditions Codabar 10 digit Narrow bar Narrow space 0 15 mm 5 9 mils 6 Under thes
134. protection sheet of the DIP switch from the CU 7000 3 Set the selectors of the DIP switch as shown below For 115 200 bps For 57 600 bps ON 123 ON 123 OFF OFF OFF OFF For 38 400 bps For 19 200 bps on 123 on 123 OFF SFF OFF SFF DIP switch when the protection sheet is removed For 9 600 bps ON 12 3 Bottom View OFF OFF 4 Reinstall the protection sheet NOTE Do not set the DIP switch to any configurations other than one of the five shown above 5 4 2 Interface Cable Connection 1 Unplug the AC adapter of the CU 7000 from the wall socket 2 Make sure that the host computer is turned off 3 Connect the 25 pin plug Dsub 25P of the interface cable to the RS 232C interface port of the CU 7000 RS 232C interface cable 4 Connect the other end of the interface cable to the RS 232C port of the host computer 142 Chapter 5 Handling the CU 7000 Option 5 4 3 Interfacing with the Host Computer This section describes how to start communication with the host computer in System Mode The same may apply when you use a user program 1 2 3 4 7 Turn the host computer on Plug the AC adapter of the CU 7000 into the wall socket Make sure that the BHT is turned off then set it on the CU 7000 Turn the BHT power on and run System Mode Set the communications environ ments co
135. put Output CU 7000 External device 1 FG Frame ground 2 SD Send data gt 3 RD Receive data 4 RS Request to send 5 cS Ready to send 6 DR Data set ready 7 SG Signal ground 8 CD Carrier detect 20 ER Data terminal equipment ready The input output voltage threshold for the logical valued signal is listed below Logical Value Input Voltage Threshold Output Voltage Threshold 0 3V min 5V min 1 3V max 5V max 146 Chapter 5 Handling the CU 7000 Option 2 Interface Cable Connection As illustrated below connect the CU 7000 on which the BHT is put to a host computer with a cross mode cable To connect it to a modem use a straight mode cable CU 7000 Host Computer DTE DTE FG SD RD RS CS 6 1 Ea ER MOON DOR WP Cable Connection between CU 7000 and Host Computer CU 7000 Modem DTE DCE FG SD RD RS cs DR SG CD 0 ER MPMOON Doak WP Cable Connection between CU 7000 and Modem DTE and DCE In the RS 232C interface specifications the DTEs Data Terminal Equipment shall be generally connected with each other by a cross mode cable the DTE and DCE Data Circuit terminating Equipment shall be connected with each other by a straight mode cable The DTE is one piece of equipment connected at both ends of a communications line as a sender or receiver of data such as CU
136. r three seconds from the 10th ENQ to terminate the message transmission abnormally Sending Receiving station station ENQ 1 3 seconds o ENQ 2 3 seconds o ENQ 3 ENQ 10 3 seconds iin EOT Abnormal termination TIP The receiving station s default timeout is 30 seconds You may modify the timeout length on the SET PROTOCOL screen in System Mode pp 65 and 67 or by using the XFILE statement refer to the BHT BASIC Programmer s Manual BHT 100 series 165 Phase 2 Data Transmission E Normal phase 2 The sending station first sends a transmission block containing the heading text Each time the sending station receives an ACK from the receiving station it sends a transmission block containing the data texts as shown below Upon receipt of an ACK in response to the last transmission block data text n the sending station shifts to phase 3 If a transmission message contains no data text the sending station transmits the heading text only Sending station Receiving station Heading text ACK Data text 1 ACK Data text n 1 ACK Data text n ACK To phase 3 166 Appendices E Phase 2 with NAK If the sending station receives a NAK from the receiving station in response to a transmission block containing text data m it sends that transmission block again immediately as shown below If the sending station receives an
137. reens with the prompt Retry To retry the download press the Land ENT keys to abort it press the 2 and ENT keys DOWNLOAD FILE KKK KK KKK KKK Out of memory Retry 2 No DOWNLOAD FILE KKK KKK KK KKK File mismatch Retry MEZE 2 No E Problem The memory is insufficient for storing files to be downloaded E Solution Press the 2 key to return to the SYSTEM MENU then delete unnecessary files in the memory or decrease the size of the file to be downloaded Refer to Subsection 2 5 3 7 and 2 E Problem You attempted to download the BHT system pa rameter file or system message file E Solution Check the file you attempted to download Press the 2 key to return to the SYSTEM MENU and then download the file in the appropriate menu SYS TEM PARAMETER transfer menu or SYSTEM MES SAGE transfer menu Refer to Subsection 2 5 3 8 and 10 49 DOWNLOAD FILE KR KKM KKM KKK Too many files Retry MSZA 2 No DOWNLOAD FILE XXXXXXXX XXX Communication errortt Retry MEZ 2 No DOWNLOAD FILE XXXXXXXX XXX File error Retry MSZA 2 no E Problem The current download will exceed the maximum of 80 files in the memory E Solution Press the 2 key to return to the SYSTEM MENU Delete unnecessary files in memory or decrease the number of files to be downloaded if you at tempted to download more than one file Refer to
138. ridge loaded or with a discharged bat tery cartridge loaded even if the resume function had been set to ON NOTE The BHT displays this error message for 3 seconds and automatically runs the execution program from the point of start up Error in System Mode settings E Problem Your settings made in System Mode contain an er ror NOTE e If this error occurs the System Mode ae settings revert to the factory defaults e The BHT displays this error message for three seconds and then displays the No execution program selected message E Solution Make your settings in System Mode again 132 Reload the battery to restart A7VOAIINXK AHOD N aQ0 a t e i i S P P R Contact your administrator Note the error number Chapter 4 Error Messages System down error E Problem An error has occurred during execution of System Program NOTE If this error occurs the BHT beeps five times for 0 1 second per beep E Solution Unload and reload the battery cartridge then turn on the power If this error occurs frequently make a note of the message and codes on the LCD and contact your nearest dealer System administrator to be called E Problem Any of the following errors has occurred 1 Hardware error Calendar clock error 1010 Flash memory error 1020 2 Memory storage error 2XXX 3 Execution program error 3010 XXXX Error code TIP If any of the
139. s Lost 31 1 Press the 2 key while holding down the SF key The screen will switch to the following Do you want to run Scandisk 1 Yes 2 No 1 YES Run Scandisk and start the System 2 NO Turn the BHT off 2 Choose either one with the numerical keys and press the ENT key When Scandisk is in progress the following message is displayed Scandisk is checking your drive for errors 32 Chapter 2 Getting Started the BHT and System Mode If Scandisk finds an invalid file s the following screen will appear As long as an invalid file exits that screen displays every time the BHT System is started up Scandisk found invalid files Refer to the file S S BRKLST SYS for more information 3 Press the ENT key to start up the BHT System E Scandisk when the resume function is enabled If Scandisk runs when the resume function is enabled the screen given below may appear The screen may also appear when the calendar clock built in the BHT stops even without running Scandisk The BHT displays the screen for three seconds and then automatically runs the execu tion program from the beginning No resume info has been retained Program restarts automatically 33 3 About BRKLST SYS If Scandisk finds an invalid file s it will automatically create the BRKLST SYS file To check the contents of the file upload the file in System Mode to the
140. s and related symbols given below before you proceed to the text itself A WARNING Alerts you to those conditions which could cause seri ous bodily injury or death if the instructions are not followed correctly Alerts you to those conditions which could cause minor A CAUTION bodily injury or substantial property damage if the in structions are not followed correctly Meaning of Symbols A triangle ZA with a picture inside alerts you to a warning of danger Here you see the warning for electrical shock A diagonal line through a circle alerts you to something you should not do it may or may not have a picture inside Here you see a screwdriver inside the circle meaning that you should not disassemble A black circle with a picture inside alerts you to something you MUST do This example shows that you MUST unplug the power cord AP A WARNING Handling the battery cartridge e Never disassemble or heat the battery cartridge nor put it into fire or water doing so could cause battery rupture or leakage of battery fluid resulting in a fire or bodily injury Do not carry or store the battery car tridge together with metallic ball point pens necklaces coins hairpins etc Doing so could short circuit the termi nal pins causing the batteries to rup ture or the battery fluid to leak result ing in a fire or bodily injury Avoid dropping the battery cartridge or letting it undergo any shock or impac
141. s are assigned the trigger switch function by default You can make them function as the SF key ENT key or backlight function on off key If you define the M4 key as the backlight function on off key pressing the M4 key activates or deactivates the backlight function In user programs a string data can also be assigned to these magic keys NOTE The backlight function on off key can be assigned only to any one of M1 through M 4keys The key defined more recently will act as the backlight function on off key and one defined earlier will be ignored That is if you define the M1 and M2 keys as the backlight function on off key in this order the M2 key will work as the backlight function on off key and the M1 key s entry will be ignored 72 Chapter 2 Getting Started the BHT and System Mode Enabling disabling the function keys SET FUNC KEY Selecting the 6 FUNC KEY on the SET KEY menu calls up the screen shown at left 2 F1 F4 ON Highlighted is the current setting 3 F1 F8 ON 1 ALL OFF Disables all function keys 2 F1 F4 ON Enables four function keys F1 through F4 w F1 F8 ON Enables all of the eight function keys F1 through F8 Select a desired setting by using the numerical keys or M1 and M2 keys and then press the ENT key The screen returns to the SET KEY menu Display positions of function keys When 2 F1 F4 ON is When 3 F1 F8 ON is select
142. s turned on Sets the message version English or J apanese Sets the calendar clock date and time Sets the special code scan ning parameters the black and white inverted label reading marker view finder option data and the minimum number of dig its to be read for bar codes ITF and Codabar Sets the special bar code scanning parameters the black and white inverted label reading and the de coding level and the mini mum number of digits to be read for bar codes ITF STF and Codabar Sets the communications environments interface port and communications parameters Defines the functions of the shift key magic keys and function keys Sets the resume function Select a desired item by using the numerical keys or M1 and M2 keys and the selected item be comes highlighted Then press the ENT key Press the C key to return to the SYSTEM MENU 54 Chapter 2 Getting Started the BHT and System Mode 4 1 Setting an execution program SET EXEC PROGRAM SAMPLE 2 PD3 SAMPLE 3 PD3 SAMPLEO4 PD3 SAMPLES PD3 SET EXEC PROGRAM DC HE ak ke IE ke fe ate oe te fe ate ote ie oe oe NO FPELE _EXrsTs 3k ak ak ake ke gt fe k e 3k k k c e Fe Selecting 1 EXEC PROGRAM on the SET SYS TEM menu calls up the screen shown at left Highlighted is the current setting Use the M1 and M2 keys to move the cursor to a desired execution program
143. s with the BHT 100Q and check the read data displayed on the LCD Upon completion of 2D code amp bar code reading the BHT 100Q beeps turns on the indicator LED in green and displays the read data together with the code type and the number of data digits If the read data is a 2D code containing the small number of digits or a bar code it will display as shown in Sample 1 If the read data is a 2D code containing the large number of digits all data may not display on a single screen You may scroll the screen line by line or page by page by using the M1 and M2 keys or SF M1 and SF HM2 keys respectively xxxx Shows that this page starts with this digit of the read data Shows the total number of digits of the read code 76 Chapter 2 Getting Started the BHT and System Mode Listed below is a table showing the relationship between the 2D code bar code types and the identifier letters to be displayed on the LCD Code 39 sample Code Type ID Letters TES ORCODE m 999270007 QR Code 3 PDF417 h MaxiCode X Data Matrix Z EAN 13 UPC A A EAN 8 B UPC E C Interleaved 2of5 ITF l Codabar NW 7 N Code 39 M Code 128 K EAN 128 Ww The minimum number of digits to be read depends on the scanning parameter setting Refer to 4 4 To return to the TEST menu press the C key TIP e The QR Code system supports a split QR code feature Structured Append w
144. so could result in a fire or electrical shock vi CAUTION Basic handling tips e Never put the BHT in places where there are excessively high temperatures such as inside closed up automobiles or in places exposed to direct sunlight Doing so could affect the housing or parts resulting in a fire e Avoid using the BHT in extremely hu mid or dusty areas or where there are drastic temperature changes Moisture or dust will get into the BHT resulting in malfunction fire or electri cal shock ANZ nn r rei f nomen li VAN e Never disassemble or modify the BHT doing so could result in an accident such as break or fire _ Never disassemble Handling the rechargeable battery cartridge Never charge a wet or damp rechargeable battery cartridge Doing so could cause the batteries to break generate heat rupture or burn Handling the BHT If smoke abnormal odors or noises come from the BHT immediately turn off the power pull out the battery cartridge and contact your AN nearest dealer Keep me Failure to do so could cause smoke or fire away from e If foreign material or water gets into the BHT immediately turn off the power pull out the battery cartridge and con tact your nearest dealer Failure to do so could cause smoke or fire vii CAUTION e If you drop the BHT so as to damage its hous ing immediately turn off the power pull out the rechargeable battery cartrid
145. station receives a sequence of DLE ACK and IDs before receiving the sequence of DLE NAK and IDs 10 times in succession it continues the subsequent message transmission Sending Receiving station Data text m station DLE NAK and IDs oe DLE NAK and IDs Data text m DLE ACK and IDs eae If the sending station receives a sequence of DLE NAK and IDs 10 times in succes sion or it fails to send a same transmission block it shifts to phase 3 to terminate the message transmission abnormally Even if phase 3 terminates normally the transmission results in an abnormal end Sending Receiving station pad station DLE NAK and IDs Data text m 2 aa Data text m 10 ecm Occurrence of an error To phase 3 178 Appendices E Phase 2 with a sequence of DLE EOT and IDs If the sending station receives a sequence of DLE EOT and IDs anytime during phase 2 it shifts to phase 3 to terminate the message transmission abnormally Even if phase 3 terminates normally the transmission results in an abnormal end Sending Receiving station station Occurrence of an error To phase 3 E Phase 2 with iterated transmission of DLE ENQ and IDs due to no response or invalid response If the sending station receives no response or any invalid response from the receiving station in response to a transmission block sent it i
146. t Doing so could cause the batteries to break generate heat rupture or burn Ch l Only use the dedicated charger CU with the 7001 C 700 or C 750 for charging the dedicated rechargeable battery cartridge Using a different type of charger could cause battery rupture or leakage of bat tery fluid and result in a fire bodily in jury or serious damage to property Undedicated Never charge the rechargeable battery cartridge where any inflam mable gases may be emitted doing so could cause fire Handling the BHT e The BHT 100B uses a laser light for indicating the scanning range The intensity of the laser light might be too low to inflict bodily injury However do not look into the laser beam The BHT 100B complies with Laser Safety Standard Class II of 21 CFR Chapter 1 Subchapter J The BHT 100B does not mount beam attenuator and laser radiation emission indicator required by this standard Instead the software controlled trigger switches see Section 2 2 Components and Func tions function as them because the laser light is not enabled without the trigger switches pressed A AVOID EXPOSURE LASER LIGHT IS EMITTED FROM THIS APERTURE A CAUTION LASER _LIGHT DO NOT STARE INTO BEAM mW MAXIMUM OUTPUT 65 nm LASER CLASS II LASER PRODUCT THIS DEVICE COMPLIES WITH 21 CFR CHAPTER 1 SUBCHAPTER J A WARNING e Do not look into the light source through the reading window or point the light source towards
147. t sis iiecseninin nin i ad adaini da vieeseteieberbeaveeaneeieees 10 Chapter2 Getting Started the BHT and System Mode ccccsccccccsesssssseeeeeeseees 11 2 1 BHT Systemi Configuration esc nea teoa aeai ted Gey et aeea aa iaa 12 2 2 Components ANd FUNCTIONS ssssssssssrssisiissstreriristitinsintinnutinnnnnnsnntnnnnnnnnnn nannan nnn nenna 17 23 Preparations a A e a A A 19 2 3 1 Setting up 1 Loading the Battery Cartridge essssssesrssisrrersrrsririssirrsrirrsrres 19 2 3 2 Setting up 2 Setting the Calendar ClOCK sssssssssssssrssesrirsrrernrisririnsinrnsrnriseres 23 2 3 3 Adjusting the LCD Contrast Beeper Volume and Touch Screen and Switching the Beeper amp Vibrator s ssssssssiesssrsisririsiietnsisrininsinnrnrnrinsrnn 24 2 3 4 Battery Voltage Display sssssssssssrssrsresrsrurenererernstanenennnnnratenerennnranantnenntnenanenenne 28 2 3 5 Battery Replacement Notes sssssssssisrssissirissintnsintinrntaskntnntnnnnnnnnnnnnnnnnnan anann nna 29 23 0 BHT Tumming off NOES rnunana a dade hae 31 2 4 Initializing the BHT SySteMirniicgiopna a 35 2 5 Operating in System Mode 2 0 ceceeeceeeee eee ee teens eens tee sete eeeeteetneeteeeteeeteeeaeetaeeeeeaeeaee 39 2 5 1 Starting System M0de w csies cutie advair nda ties 39 2 5 2 Operating in System Mode ec ceseesceceneeeeceeeseeceeseeetaesneeseeeeeeseeesaeeeaetaeeeaeeaas 43 2 5 3 Detailed Description of the Functions in System Mode ceceeeeseeeeeeeeetees 45 Chapter3 Commu
148. t COMPUEED oo eee eee eee teeter eee tetas eases enaeeaeeee 142 5 4 1 Setting the Transmission Speed of the CU 7000 0 cee eeceeeeeteeeeeteeeteeeeees 142 5 4 2 Interface Cable Connection ececceecceeeteeeeeeteeetaeeeaeeaaecaeeaaecaeeaetaesnaeeneseesnestaes 142 5 4 3 Interfacing with the Host COMpUter ce ee cece ce eeee eee eteeeteeteeetaeteeetaeeeaeeaaee 143 5 5 Charging the Rechargeable Battery Cartridge using the CU 7001 nesses 144 5 6 RS 232C Interface Specifications 0 eee cece eee eee eee teee eater tetas sees eaeeeenaeeeee 146 Appendices isch aha ae re eee et 148 Appendix A Specifications isisisi ssdpindas inina kiad annsa ii nna siaaa Aaaa anda andina n aa Saha dadika an iian 149 A OBHT I00Q aire aa a AE EAEE A E AAEE E AE TEE A AE A E RRE 149 A2 BHTLO0B innie iaa a iaaii iae aa A Ea 156 IEE E7 E E E T 161 Appendix B Communications Protocol Details sssssssssssrserssrrserserrerrntrrernnrnrrrnetnnn nenn 163 Bil BHT protocole noren het seth ee ee a 163 B2 I BH TEI Protocol riie an aa aA aie da adidas maids 173 Appendix C A Typical Basic Operation oo cece cee eeeenee eects eeaeeeeeeaeeeseeteeseneteeeneetaes 184 Appendix D Quality Assurance Standards 0 cecececseeecesee crete cceeeeeseeeeseeseeseeeteeeneetaes 185 D 1 Applicable Standards 0 ec eecceceecceeseeese cesses enaeeeseaeeeseeseseeeseeeseeeneetaeeeaetaaes 185 D2 Interface Cables ree a a ARAE EE EREA a a eee 186 deki a a a ee en a a a eet 188
149. t dealer Failure to do so could cause fire or electrical shock Use the dedicated AC adapter only Failure to do so could result in a fire Never use the CU on the line voltage other than the speci fied level Doing so could cause the CU to break or burn If the power cord of the AC adapter is damaged e g exposed or broken lead wires stop using it and contact your nearest dealer Failure to do so could result in a fire or electrical shock If you are not using the CU for a long time be sure to unplug the AC adapter from the wall socket for safety Failure to do so could result in a fire When caring for the CU unplug the AC adapter from the wall socket for safety Failure to do so could result in an electrical shock Never cover or wrap up the CU or AC adapter in a cloth or blanket Doing so could cause the unit to heat up inside deforming its housing resulting in a fire Always use the CU and AC adapter in a well ventilated area Keep the power cord away from any heating equipment Failure to do so could melt the sheathing resulting in a fire or electrical shock 141 OA A SOOO AP A Ab 5 4 Communicating with the Host Computer 5 4 1 Setting the Transmission Speed of the CU 7000 Set the transmission speed of the CU 7000 to the same value as that of the BHT and the host computer by using the DIP switch provided on the bottom of the CU 7000 1 Turn the CU 7000 upside down 2 Remove the
150. t the CALI BRATION line then press the ENT key The screen shown at left will appear Touch the center of the with the stylus The screen will switch to the following one To cancel adjustment and return to the main adjust ment screen press the C key 1 CALIBRATION Touch the center of the newly displayed h To cancel adjustment and return to the main adjust ment screen press the C key V CALIBRATION Touch the center of the newly displayed 4 To cancel adjustment and return to the main adjust ment screen press the C key 26 Chapter 2 Getting Started the BHT and System Mode CALIBRATION Touch the center of the 4th The adjustment will complete and the display will return to the main adjustment screen CALIBRATION If the adjustment is not completed normally the screen shown at left will appear where you may choose retry or not If you select 1 Yes and press the ENT key the dis play will return to the top screen of the touch screen adjustment sequence CALIBRATION NG Retry 2 No If you select 2 No and press the ENT or press the C key the display will return to the main adjust ment screen 27 2 3 4 Battery Voltage Display The battery voltage level is always displayed on the status indicator line bottom line Battery voltage level Shows the current battery voltage level Displays when the voltage level is high Displays when the voltage level is low
151. t the transmission speed character length vertical parity and stop bit length To set the transmission speed only for the optical interface use the OPEN COM statement in BHT BASIC OPEN COM Opens the interface port selected in System Mode OPEN COM1 Opens the optical interface port for data transmission irrespective of the setting in System Mode OPEN COM2 na Opens the direct connect interface port for data trans mission irrespective of the setting in System Mode Note that it is impossible to open both the optical interface port and the direct connect interface port concurrently Through the interface port opened by the OPEN COM statement the XFILI statement transmits a designated file GI 115 3 4 Communications Protocols The BHT supports both the BHT protocol and the BHT Ir protocol for file transmission 3 4 1 BHT protocol 1 Overview The BHT protocol is the communications procedure used to transmit files between the BHT and a host or between the BHTs It adopts the response method using ACK NAK codes The BHT protocol is composed of a defined set of the control character sequences including the following three phases Phase 1 Establishment of data link The sending station confirms that the receiving station is ready to receive data Phase 2 Data transmission The sending station transmits data to the target receiving station Phase 3 Release of data link The send
152. tation to be tested with their IR ports facing each other as illustrated below In this test the slave BHT transmits data to the master BHT and receives the data sent back from the master BHT Slave BHT to be tested Data 0 8 m or less Master BHT E Preparation for the direct connect interface test Arrange the 3 pole mini stereo plug as illustrated below and connect it to the direct connect interface port on the BHT a RD TEST COM Selecting the 5 COM on the TEST menu calls up the screen shown at left a OPTICAL 2 CONNECTOR 1 OPTICAL Switches to the MASTER SLAVE selection screen for the optical interface test N CONNECTOR Tests the direct connect inter face port Select a desired item by using the numerical keys or M1 and M2 keys then press the ENT key 81 Testing the optical interface port TEST COM lt OPTICAL gt 4 SLAVE 2 MASTER TEST COM lt OPTICAL gt Testing TEST COM lt OPTICAL gt se Test NG CxxdD Selecting the 1 0PTICAL on the TEST COM menu calls up the screen shown at left At the slave BHT to be tested select the 1 SLAVE and at the master BHT select the 2 MASTER Then press the ENT key on each BHT During the test the screen shown at left is dis played If any error occurs the tested slave BHT beeps three times and shows the screen at left In parentheses
153. ted together with a period 2 Data text The number of fields should be 1 to 16 If itis less than 2 digits the upper blank byte will be filled with zero 0 If the data file name is less than 12 characters in length the lower blank bytes will be filled with space characters Data field 1 Data field 2 Data field n Example of T 1 0 0 9 1 S_ 1 2 3 i Jj 9 2021413 2 5 contents Every data field should be 1 to 254 digits in length If a data field is less than the maximum digits in length the lower blank bytes will be filled with space characters NOTE The total length of all data fields plus the number of the character count bytes the number of the fields should be 255 bytes or less When you transfer five 50 digit 50 byte fields for example the total length of all data fields is 250 50 x 5 bytes and the number of the character count bytes is 5 Accordingly the total is 255 so you can transfer the file 127 This chapter lists the error messages which will appear on the LCD if some error occurs in the BHT 100Q 100B 4 1 System Errors nesses 4 2 Errors in System Mode Chapter 4 Error Messages 128 Chapter 4 Error Messages 4 1 System Errors If some error occurs when the power is turned on or during program execution one of the following error messages will appear on the LCD Battery voltage has Lowered System Program error
154. terates sending of a sequence of DLE ENQ and IDs at 0 5 second intervals up to 59 times If the sending station receives a sequence of DLE ACK and IDs before sending the sequence of DLE ENQ and IDs 59 times it continues the subsequent message transmission Sending i Receiving station station Data text m 0 5 second el DLE ENQ and IDs 0 5 second 2S DLE ENQ and IDs Data text m pe 179 E Abnormal termination of phase 2 Abort of phase 2 If the sending station receives no sequence of DLE ACK and IDs from the receiving station after sending a sequence of DLE ENQ and IDs 59 times in succession it sends a sequence of DLE EOT and IDs to the receiving station after 0 5 second from the 59th sequence of DLE ENQ and IDs and then aborts this transmission abnor mally Sending Receiving station station 0 5 second DLE ENQ and IDs 1 0 5 second DLE ENQ and IDs 2 I I I DLE ENQ and IDs 59 0 5 second DLE EOT and IDs Abnormal termination Phase 3 Release of Data Link E Normal phase 3 The sending station transmits a sequence of DLE EOT and IDs to the receiving station Upon receipt of a sequence of DLE ACK and IDs from the receiving station the sending station terminates the message transmission normally and releases the data link Sending Receiving station DLE EOT and IDs station DLE ACK and IDs Normal termination 18
155. tes the end of data text Phase 2 In the BHT Ir protocol you cannot change the values of the headers and terminator with the protocol functions in BHT BASIC 124 Chapter 3 Communications Operations of the BHT 100Q 100B 3 Basic Format of Transmission Messages Basically the BHT transmits data as units of a file First it transmits a heading text which includes the attribute information of a file e g file name and the number of data texts to be transmitted Following the heading text it transmits the data text in the file A heading text and data text comprise a text In actual text transmission the text is divided into several blocks then a header terminator serial number receiver station s ID and CRC 16 Cyclic Redundancy Check are added to each block This procedure forms a transmission block A set of transmission blocks makes up one transmission message Shown below is an example of a transmission message formed with the BHT Ir protocol Text Beseing Data text 1 Data text 2 Data text n S l Ee Transmission L O Heading text Le T R block H D E XJC 2 bytes S Serial D E C nt Oe Transmission Transmission L T number Data text 1 L T R block Message X D 5 bytes E X C S l Serial D EJC oe Data text n Transmission Le T number L T R plock E XID XIc In the above figure DLE SOH DLE ST
156. the above screen does not appear follow the calendar clock setting procedure given in Subsection 2 5 3 4 3 to set the calendar clock 23 2 3 3 Adjusting the LCD Contrast Beeper Volume and Touch Screen and Switching the Beeper amp Vibrator While holding down the M1 key or right hand trigger switch M4 press the PW key The main adjustment screen appears which differs depending upon the current state as shown below After adjustment press the ENT key or no keys for five seconds The new settings will be registered and the main adjustment screen will disappear When the beeper is selected 1 default xD 2 BEEPER 3 BEEPER VOLUME TOUCH SCREEN 4 VOLUME 5 CALIBRATION ENT When the vibrator is selected 1 Li VIBRATION TOUCH SCREEN 4 VOLUME 5 CALIBRATION ENT When both the beeper and 1 vibrator are selected LCD CONTRAST 2 BEEPER VIBRATION 3 BEEPER VOLUME TOUCH SCREEN 4 VOLUME 5 CALIBRATION ENT The current selection is highlighted 24 Chapter 2 Getting Started the BHT and System Mode Adjusting the LCD contrast You can adjust the LCD brightness to eight contrast levels 1 Use the 1 key or M1 or M2 key to select the LCD CONTRAST line 2 To decrease the contrast press the M1 key with the SF key held down to increase it press the M2 key with the SF key held down Switching the beeper amp
157. to be run when the power is applied and then press the ENT key To return to the SET SYSTEM menu press the C key If no program files are stored in the memories the screen shown at left will appear To return to the SET SYSTEM menu press the C key 55 4 2 Setting the message version SET DISPLAY ee ee English Japanese Selecting 2 DISPLAY on the SET SYSTEM menu calls up the screen shown at left Highlighted is the current setting 1 MESSAGE Switches the message version to English or J apanese for system error messages and indications on the screen for the LCD con trast beeper volume and touch screen adjustment and the beeper amp vibrator switching The de fault is the message version that you selected in the initializing se quence Select a desired setting by using the M1 and M2 keys with the SF key held down Press the ENT key To return to the SET SYSTEM menu press the C key 56 Chapter 2 Getting Started the BHT and System Mode 4 3 Setting the calendar clock SET DATE TIME Q O 01 01 88 00 x a SET DATEYTIME O0 01 01 88 00 o0 04 19 16 00_ SET DATE TIME 0 04 19 16 00 ZF fF Selecting 3 DATE TIME on the SET SYSTEM menu calls up the screen shown at left Use the numerical keys to enter the year only the last two digits month day hour and minute in this order and then press the ENT key If the data is in one digit
158. tting Started the BHT and System Mode E Problem The memory is insufficient for setting up the sys tem message file E Solution Press the C key to return to the SYSTEM MENU then delete unnecessary files in the memory Re fer to Subsection 2 5 3 7 E Problem The memory has already contained 80 files so the BHT system message file cannot be set up E Solution Press the C key to return to the SYSTEM MENU then delete unnecessary files in the memory Re fer to Subsection 2 5 3 7 E Problem Uploading has failed E Solution To retry uploading press the 1 key Pressing the 2 key returns to the SYSTEM MENU Check the interface port communications param eters and communications protocol type in the SET SYSTEM menu or perform the communica tions test in the TEST menu Refer to Subsection 2 5 3 4 5 and 5 5 It is also necessary to check the communications parameters setup of the host computer 107 Chapter 3 Communications Operations of the BHT 100Q 100B This chapter describes the communications operations of the BHT 100Q 100B the IR communication RS 232C interface specifications the basic communications specifica tions and the communications protocols for data transfer with the host computer or other devices 3 1 Infrared Communication i iiien urena aiaiai eee adaa 109 3 2 RS 232C Interface Specifications 0 0 ce eceeeeecseeseeeeeeneeeeeseeeeseetsaesneeneeeneenetneetaes 111
159. up by the BHT BASIC Interpreter or System Mode BHT BASIC Interpreter The interpreter interprets and executes instructions in user programs written in BHT BASIC 15 System Mode System Mode is a system program exclusively designed for the effective use of user programs in the BHT It sets up the execution environments for those programs e g it prepares downloading uploading conditions sets the calendar clock and tests the BHT components including the LCD beeper and keypad Shown below is the System Mode menu SYSTEM MENU SYSTEM MENU L EXEC PROGRAM 2 DOWNLOAD 3 UPLOAD 4 SET SYSTEM S TEST G VERSION E JIS Level 1 and Level 2 Font Files These files contain font data required for displaying Kanji characters on the LCD The BHT can display the Kanji characters not only in the conventional standard size font 16 dots wide by 16 dots high but also in the small size font 12 dots wide by 12 dots high in application programs It can also display the double width double height and quadruple size double width amp height Kanji characters of those 16 dot and 12 dot fonts in application programs TIP If you do not need to display Kanji characters you may delete these JIS font files After deletion the memory area which was occupied by these files can be used as a user area For the deleting procedure refer to Section 2 4 Initializing the BHT System or Subsection 2 5 3 7 Deleting Files
160. use the CU 7000 where you expect to do a lot of connecting and disconnecting of the BHT to from a host compu ter E BHT BASIC Compiler option This Compiler compiles a source program written in BHT BASIC by an editor of the host computer running the MS DOS into the object program user program which can be used in the BHT The compiled and linked program file is named XXX PD3 XXX File name you can Set arbitrarily under the MS DOS rules You should download it to the BHT by using Ir Transfer Utility C lr Transfer Utility E Transfer Utility 13 E Ir Transfer Utility C option Running on the host computer this utility transfers files between the BHT and the host computer For its file transfer control procedure the utility uses the BHT Ir protocol For the details about the BHT Ir protocol refer to Chapter 3 Subsection 3 4 2 To transfer files under any of the following conditions use Ir Transfer Utility C At transmission speeds of 115200 or 57600 bps This may be impossible de pending upon the host computer type When the BHT is placed on the CU 7000 Via the direct connect interface of the BHT E Ir Transfer Utility E option Running on the host computer this utility transfers files between the BHT and the host computer For its file transfer control procedure the utility uses the BHT Ir protocol For the details about the BHT Ir protocol refer to Chapter 3 Subsection 3 4 2 To transfer files under an
161. ving station Data text n station 30 seconds DLE EOT and IDs Abnormal termination 2 Aborting Data Transmission Pressing the C key aborts data transmission If the C key is pressed during downloading the BHT transmits a sequence of DLE EOT and IDs and aborts the file transmission If it is pressed during uploading the BHT transmits the current transmission block followed by a sequence of DLE EOT and IDs and then aborts the file transmission 182 Appendices 3 CRC To check whether data has been transmitted accurately the BHT Ir protocol supports CRC Cyclic Redundancy Check which employs the CRC 16 generating system In CRC a CRC character is suffixed to a sequence of DLE ETX of every transmission block Operands for CRC 16 The CRC generates CRC 16 from all bytes of a transmission block excluding DLE SOH or DLE STX characters which are at the head of a transmission block DLE character of DLE ETX and DLE character of DLE DLE in the text CRC operation The CRC system generates CRC 16 as follows It multiplies the polynomial formed by aligning all of the bits starting from the LSB of the first byte to the MSB of the last byte in a transmission block in descending order by X16 Next divide the polynomial by the generative polynomial X16 X15 X2 1 The remainder is the value of CRC 16 Shown below is a data text transmission block and operands for CRC 16 generation
162. wn at left 1 J apanese Switches the message version to J apanese 2 English Switches the message version to English Select a desired item by using the numerical keys then press the ENT key 36 Chapter 2 Getting Started the BHT and System Mode 3 Confirming the memory area selected for initialization INITIALIZE INITIALIZE OK 1 Yes 2 Nol Warning Initializing the whole user area witli Lose the Font files 4 During initialization INITIALIZE Initializing Progress in initialization Selecting the USER AREA EXCEPT FONTS in step 1 above will call up the confirmation screen shown at left 1 Yes Starts initialization 2 No Cancels initialization and turns the power off Select a desired item by using the numerical keys then press the ENT key Pressing the C key will switch the screen back to the area selection screen Selecting the WHOLE USER AREA in step 1 above will call up the screen shown at left 1 Yes Starts initialization 2 No Cancels initialization and turns the power off Select a desired item by using the numerical keys then press the ENT key Pressing the C key will switch the screen back to the area selection screen During initialization the screen shown at left is displayed 37 5 Completion of initialization Upon completion of the initialization the BHT dis
163. x 17 cells 2 0 25 mm 9 8 mils 1 Applies to Model 2 2 Applies to MicroQR 2 PDF417 Number of columns and number of rows Module size 1 to 5 columns 3 to 30 rows 3 0 17 mm 6 7 mils 3 Excluding start stop codes and left and right indicators 3 MaxiCode Module size Module pitch 30 29 x 33 modules 0 88 mm 34 6 mils 4 Data Matrix Code size Cell pitch Max 80 x 80 cells 0 25 mm Max 52 x 52 cells 0 33 mm 4 Bar Codes Bar code type Bar dimensions Readable range Universal product codes EAN 13 EAN 8 UPC A UPC E Interleaved 2of5 ITF Codabar NW 7 Code 39 Code 128 EAN 128 0 26 to 0 33 mm 10 24 to 12 99 mils 0 26 to 0 46 mm 10 24 to 18 11 mils 0 26 to 0 33 mm 10 24 to 12 99 mils 0 26 to 0 56 mm 10 24 to 22 05 mils 0 15 mm min 5 91 mils 0 8 to 1 0 magnifications 0 8 to 1 4 magnifications 0 8 to 1 0 magnification 0 8 to 1 7 magnifications 2 to 34 digits 3 to 23 digits 1 to 17 digits 1 to 21 digits Only even numbered digits All of the above values are under the following conditions Ambient illuminance 500 to 3000 2x Light source Xenon lamp 5 Multi line Code Scanning The BHT 100Q supports multi line code scanning that can scan up to 3 lines of codes out of universal product codes Interleaved 2of5 ITF Codabar NW 7 Code 39 and Code 128 EAN 128 at a time in the specified order The multi lin
164. xts should be 0 to 32767 If itis less than 5 digits the upper blank bytes will be filled with zeros 0 If the data file name is less than 12 characters in length the lower blank bytes will be filled with space characters Every data field should be 1 to 254 digits in length If itis less than 2 digits the upper blank byte will be filled with zero 0 If a data field is 100 to 199 digits in length 0 to 19 will be given if it is 200 to 254 digits PO to U4 will be given 10X 20X P 11X A 21X Q 12X B 24X T 18X H 25X U 19X l The number of fields should be 1 to 16 Ifitis less than 2 digits the upper blank byte will be filled with zero 0 NOTE To transfer a data file containing a data field s of 100 digits or more use the Windows based Transfer Utility The MS DOS based Transfer Utility does not support transmission of data fields exceeding 99 digits 2 Data text Data field 1 Data field 2 Data field n Example of T 1 0 0 9 1 S 1 2 3 contents i 1990 0 4 4 1305 EA If a data field is less than the maximum digits in length the lower blank bytes will be filled with space characters NOTE The total length of all data fields plus the number of the character count bytes the number of the fields should be 255 bytes or less When you transfer five 50 digit 50 byte fields for example the total length of all
165. y of the following conditions use Ir Transfer Utility E Via an external IR transceiver Via an IR port integrated in a computer E Transfer Utility option Running on the host computer this utility transfers files between the BHT and the host computer For its file transfer control procedure the utility uses the BHT protocol For the details about the BHT protocol refer to Chapter 3 Subsection 3 4 1 To transfer files under any of the following conditions use Transfer Utility When the BHT is placed on the CU 7000 Via the direct connect interface of the BHT 14 Chapter 2 Getting Started the BHT and System Mode Software Structure System Programs and J IS Level 1 amp Level 2 fonts are resident in the system area and user area respectively To use extension programs and user programs you should download the program files into the user area To use data files e g goods master files required for execution of user programs you should download those data files before execution of user programs Those files will be stored in the user area J IS Level 1 System amp Level 2 User programs Programs font files Program Data files files System Area User Area Host Computer E System Programs The system programs include the following three sets of programs Drivers Drivers is a set of programs that directly controls the BHT hardware It may be called
166. ystem Mode 1 Program Execution Selecting 1 EXEC PROGRAM on the SYSTEM MENU calls up the screen shown at left EXECUTE PROGRAM SAMPLE 2 PD3 SAMPLE 3 PD3 SAMPLE O4 PD3 SAMPLE O S PD3 SAMPLE G PD3 SAMPLEO 7 PD3 SAMPLE 8 PD3 SAMPLE 9S PD3 SAMPLE10 PD3 SAMPLE11 PD3 SAMPLE12 PD3 SAMPLE13 PD3 SAMPLE14 PD3 SAMPLE15 PD3 SAMPLE16 PD3 SAMPLE17 PD3 SAMPLE18 PD3 SAMPLE19 PD3 SAMPLE20 PD3 SAMPLE21 PD3 SAMPLE22 PD3 If more than one program has been downloaded to the user area of the target memory use the M1 and M2 keys to move the cursor to a target program and then press the ENT key To return to the SYSTEM MENU press the C key EXECUTE PROGRAM If more than 22 programs have been downloaded SAMPLEO1 PD3 you may need to scroll the screen with the M2 key SAMPLE 2 PD3 SAMPLE O3 PD3 SAMPLEO4 PD3 SAMPLE S PD3 SAMPLEOG PD3 SAMPLE 7 PD3 SAMPLE 8 PD3 SAMPLEOSO PD3 SAMPLE10 PD3 SAMPLE11 PD3 SAMPLE12 PD3 SAMPLE13 PD3 SAMPLE14 PD3 SAMPLE15 PD3 SAMPLE16 PD3 SAMPLE17 PD3 SAMPLE18 PD3 SAMPLE19 PD3 SAMPLE20 PD3 SAMPLE21 PD3 SAMPLE22 PD3 EXECUTE PROGRAM SAMPLE 2 PD3 SAMPLE Q3 PD3 SAMPLEO4 PD3 SAMPLEOS PD3 SAMPLEOG PD3 SAMPLE 7 PD3 SAMPLE 8 amp PD3 SAMPLEOS9S PD3 SAMPLE10 PD3 SAMPLE11 PD3 SAMPLE12 PD3 SAMPLE13 PD3 SAMPLE14 PD3 SAMPLE15 PD3 SAMPLE16 PD3 SAMPLE17 PD3 SAMPLE18 PD3 SAMPLE19 PD3 SAMPLE20 PD3 SAMPLE21 PD3 SAMPLE22 PD3 SAMPLE23 PD3 45 1 EXECUTE PROGRAM SAMP

Denso BHT-100B Scanner User Manual

Contents

Download Pdf Manuals

Related Search

Related Contents