DeLonghi ESAM6600 Coffeemaker User Manual
Contents
1. JeLonghi Fiducia Italiana 5 de C V Pestalozzi 814 Col Narvarte Del Benito Juarez C P 03100 tels 5543 1447 lada sin costo 01 800 711 8805 www delonghi com 5732148500 12 06 FULLY AUTOMATIC COFFEE CENTER ESAM6600 IMPORTANT INSTRUCTIONS SAVE THESE INSTRUCTIONS MACHINE CAFE AUTOMATIQUE ESAM6600 i MODE D EMPLOI IMPORTANT CONSERVEZ LES PRESENTES INSTRUCTIONS CAFETERA SUPERAUTOMATICA ESAM6600 INSTRUCIONES IMPORTANTES REPASE Y GUARDE E STAS INSTRUCCIONES LEA ESTE INSTRUCTIVO ANTES DE UTILIZAR EL APARATO MACCHINA PER CAFF SUPERAUTOMATICA ESAM6600 ISTRUZIONI IMPORTANTI CONSERVARE LE ISTRUZIONI Register this product on line and receive a free trial issue of Cook s Illustrated Visit http registration delonghi csservice com Visit www delonghi com fora list of service centers near you U S and Canada only Enregistrez ce produit en ligne et recevez un num ro gratuit de Cook s Illustrated Visitez http registration delonghi csservice com Visitez www delonghi com pour y voir une liste des centres de r paration proches de chez vous U et Canada seulement Registre este producto en l nea y reciba un ejemplar gratis de Cook s Illustrated Visite http registration delonghi csservice com Visite www delonghi com para ver la lista de centros de servicios cercanos a usted S lo Estados Unidos y Canada Registra questo prodotto on line per ricevere un2. Wrong type of coffee is being used The coffee is ground too finely SOLUTION Heat the cups by rinsing them in hot water or leaving them for at least 20 minutes on the cup warmer tray on the lid see section 6 note 3 Heat the infuser by pressing the D button before making the coffee fig 12 see section 6 note 3 Turn the grinding adjustment knob one click toward the number 1 see section 8 Use a type of coffee for espresso coffee makers Turn the grinding regulator one click toward the number 7 see section 8 The coffee runs out too quickly The coffee is ground too coarsely Turn the grinding regulator one click toward the number 1 see section 8 The coffee does come out of one of the spouts not The spout holes are blocked Scrape off the dry coffee residues with a needle fig 29 When coffee beans are being used and the W buttons are pressed the appliance does not deliver coffee but only water The ground coffee may be blocked the funnel Remove the ground coffee inside the funnel using a knife see section 9 note 5 Then clean the infuser and the inside of the appliance see description in section 16 2 When the button is pressed the appliance does not turn on The appliance is not plugged in Check that the power cable is plugged into the outlet The infuser cannot be removed for cleaning The appliance is on
3. De Longhi addresses The above warranty is in lieu of all other express warranties and representations All implied warranties are lim ited to the applicable warranty period set forth above This limitation does not apply if you enter into an extended warranty with De Longhi Some states do not allow limitations on how long an implied warranty lasts so the above exclusions may not apply to you De Longhi does not authorize any other person or com pany to assume for it any liability in connection with the sale or use of its appliance How does state law apply This warranty gives you specific legal rights and you may also have other rights which vary from state to state
4. To change these quantities proceed as follows Fill the container with milk up to the maximum level indicated on the container Press the button corresponding to the preparation you want to change LATTE CAPPUCCINO ITALIAN MACCHIATO for at least 8 seconds until the appliance emits a BEEP and displays FILA FOR PROGRANQUANTITS Then release the button The appliance starts delivering milk Once the required quantity of milk has been delivered press the button selected previously again Milk delivery stops and the quantity is memorized The appliance emits a After a few seconds the appliance delivers coffee into the cup and displays COFFEEFOR PROGRAMQUANTITO Once the required quantity of coffee has been delivered press the button selected previously again Coffee delivery stops and the quantity is memorized A double BEEP confirms that the new values have been memorized The appliance is now re programmed with the new settings and displays READY 16 CLEANING AND MAINTENANCE Before performing any cleaning operations leave the appliance to cool down and unplug from the outlet Never immerse the coffee maker in water It is an electrical appliance Do not use solvents abrasive cleaning products or alcohol to clean the appliance A soft damp cloth will suf fice No component may be washed in the dishwasher 16 1 Cleaning the coffee maker Clean the grounds container as described in section 6 note 7 when
5. When the message DESCALE flashes on the display you should perform the descale cycle Proceed as follows Make sure the appliance is ready Press the P button then press the lt button corresponding to the gt symbol flashing on the display then press the button repeatedly until the appliance displays gt DESCALENO Press the 2 button corresponding to the SET symbol flashing on the display and the appliance dis plays GESCALE YES Press the OK button to start the descale program Empty the water tank and pour in the contents of one bottle 4 2 fl oz of DURGOL descaler plus 34 oz of water NOTE Make sure splashes of descaler do not fall onto surfaces sensitive to acid such as marble lime stone and granite For subsequent descaling operations use the same type and brand of descaling solution as supplied avail able from authorized technical service centers Attach the water spout to the nozzle Place a container with a minimum capacity of 34oz under the hot water spout Fig 3 Press the OK button Descaler runs off from the hot water spout into the container below The appliance displays APPLIANCE IN DESCALE The descale program automatically performs a series of run offs and pauses to remove lime scale deposits from inside the coffee maker After about 30 minutes the appliance displays RINSING FILL TANK The appliance must now be rinsed through to eliminate residues of descaling sol
6. a short coffee less than 2 07 use the hot rinse through water to preheat the cups If more than 2 3 minutes have passed since you last made coffee before making coffee again you must pre heat the infuser by pressing the button lt fig 12 Run off the water into the underlying drip tray or alternatively use this water to fill and then empty the cup to be used for the coffee so as to preheat it Unless preheated do not use cups that are too thick as they will absorb too much heat Use cups that have been preheated by rinsing them with hot water or by leaving them for at least 20 min utes on the cup warmer tray on top of the appliance with the appliance on NOTE 4 While the appliance is making the coffee delivery can be stopped at any time by pressing the cof fee button previously selected fig 10 Collection SCLUSIVO NOTE 5 As soon as delivery is complete to increase the quantity of coffee simply press and hold the coffee button previously selected fig 10 until the desired quantity is reached this operation must be performed within 3 seconds from when coffee delivery from the spouts ceases NOTE 6 When the appliance displays FILL TANK and emits a double BEEP the water tank must be refilled or the appliance will not make coffee It is normal for there to be a little water left in the tank when the message is displayed NOTE 7 The appliance counts the number of coffees made Ev
7. as follows Remove the milk spout 1 and intake tube 2 Remove the froth regulator 3 by pulling it outwards see figure Wash all the components thoroughly with hot soapy water Make sure there is no milk residue inside the two holes in the lid of the milk con tainer indicated by the arrows in the figure or in the groove 4 of the froth regulator Replace the froth regulator intake tube and milk spout back in the milk container lid 17 CHANGING AND SETTING THE MENU PARAMETERS After pressing the T button when the appliance is ready you can use the internal menu to modify the fol lowing parameters and functions Clock Auto start time Auto start ON OFF Descaling process Coffee temperature Length of time the appliance remains on Water hardness Resetting factory default values Washing procedure ON OFF Note the last line of the display is the guide to the function buttons 17 1 Setting the clock To set the clock proceed as follows Press the P button then press the button corresponding to the symbol flashing on the display repeatedly until the menu arrow is on gt chock 00 00 Press the button corresponding to the SET symbol flashing on the display to set the time on the clock If you hold the button down the time is changed rapidly Press the OK button to confirm the value Press the P button corresponding to the ESC symbol flash
8. contact your electrician to replace your obsolete outlet Do not defeat the safety purpose of the polarized plug SCLUSIVO Collection L 7 1 DESCRIPTION SEE PAGE 3 SEHNRENOZETrAK TTanmonp gt Grinding coarseness regulator Control panel Coffee bean container Some ofthe buttons on the panel have a dual function This is Bean container lid indicated in parentheses in the description Central lid for ground coffee 1 Appliance ON OFF button Compartment for measuring scoop 2 Display Cup warmer tray 3 One short coffee button Ground coffee funnel 4 Two short coffees button Milk container lid with milk frother regulator 5 One long coffee button Milk spout 6 Two long coffees button Milk intake tube 7 Button for one Italian macchiato or frothed Nozzle milk if pressed twice consecutively Water tank removable 8 Button for one cappuccino or frothed milk if Milk container pressed twice consecutively Power cable 9 Button for one latte or steamed milk if pressed Cup tray twice consecutively Measuring scoop for pre ground coffee 10 Button to select coffee strength or preparation Drip tray removable with pre ground coffee OK button to confirm Hot water spout changes to menu settings Service door 11 Hot water button SET button to change menu Coffee grounds container removable settings Coffee spout adjustable in height 12 Rinse button gt button to change menu set Mobile drawer tings W Infuser 13 P b
9. the infuser by sliding it onto the supports and pin at the bottom then push the PUSH symbol fully in until it clicks into place SCLUSIVO Collection 5 EB Push the PUSH symbol fully in until it clicks into place After having heard the click check that the red buttons have snapped out Support Pin Bottom pipe on the infuser The pin must be inserted into the bottom pipe on the infuser Check that the two red buttons have snapped out otherwise the door cannot be closed The two red buttons have not snapped out The two red buttons have o snapped out CORRECTLY gt EE CORRECT INCORRECT Replace the drip tray complete with the grounds container Close the service door NOTE 1 If the infuser is not inserted correctly until it clicks into place and the two red buttons have not snapped out the service door cannot be closed NOTE 2 If it is hard to insert the infuser before inserting it squeeze it to the right size by pressing it forcefully from the top and bottom simultaneously as shown in figure NOTE 3 If it is still hard to insert the infuser leave it out of the appliance close the service door unplug from the outlet then plug in again Wait for all the lights to go off after the diagnostics then open the door and replace the infuser EN Collection SCLUSIVO L 7 16 3 Cleaning the milk container Proceed
10. ING THE QUANTITY OF HOT WATER The appliance is factory preset to automatically deliver 8 5 oz of hot water To change this quantity proceed as follows Make sure the water spout is attached fig 4 Position a container under the spout fig 3 Press the 8 button fig 17 for at least 8 seconds until you hear a BEEP then release The appliance dis plays HOTWATER PROGRAM QUANTITY and hot water is delivered from the water spout When the hot water in the cup reaches the required level press the 8 button to memorize the new amount The appliance emits a double beep You should not run off hot water for more than two minutes at a time 12 PREPARING CAPPUCCINOS FROTHED MILK AND COFFEE Select the required coffee strength to make the cappuccino by pressing the OK 0 4 button fig 1 Remove the frothed milk lid from the milk container Fill the container with about 3 5 oz of milk for each cappuccino to be prepared fig 18 Never exceed the MAX level corresponding to about 25 oz marked on the container It is best to use fat free or low fat milk at refrigerator temperature about 41 F 5 C Make sure the milk intake tube is correctly inserted in the rubber washer on the bottom of the milk con tainer lid fig 19 then reposition the lid in the milk container and turn it counter clockwise as far as it will go Move the pointer on the milk container to position 2 fig 20 Remove the hot wate
11. ROUND COFFEE INSTEAD OF BEANS 12 10 PRODUCING HOT WATER eee des 13 11 CHANGING THE QUANTITY OF HOT WATER enn 13 12 PREPARING CAPPUCCINO FROTHED MILK AND COFFEE 13 13 PREPARING LATTE OR ITALIAN MACCHIATO Hehe 14 14 PREPARING FROTHED OR STEAMED MILK WITHOUT COFFEE 14 15 CHANGING THE QUANTITY OF COFFEE AND MILK FOR LATTE CAPPUCCINO ITALIAN MACCHIATO rr 15 T6 CLEANINGAND MAINTENANCE cotorra ERRARE RERENEU REM KEY ESSERE RE 15 16 1 CLEANING THE COFFEE MAKER eco repro EE eher EIER nee 15 16 2 CLEANING THE INFUSER vu e PIE en 15 16 3 CLEANING THE MILK CONTAINER u eee een en rex eR 17 17 CHANGING AND SETTING THE MENU PARAMETERS 17 17 17 2 SETTING AUTO START TIME ana rs 17 17 3 DESCALING su ee essen 18 17 4 CHANGING THE COFFEE TEMPERATURE xe PR ST RI RR e tori 19 17 5 CHANGING THE LENGTH OF TIME THE APPLIANCE REMAINS ON 19 17 6 SETTING WATER HARDNESS u sa pus et CREE Y RS 19 17 7 RESETTING FACTORY DEFAULT SETTINGS Rr nn 19 17 8 BEERON ORF 20 18 CHANGING THE LANGUAGE eu na ernennen 20 19 TROUBLESHOOTING u ns a
12. The infuser can only be removed if the appliance is off Turn the appliance off and remove the infuser see section 16 2 IMPORTANT The infuser can only be removed if the appliance is off Attempting to remove the infuser with the appliance on may cause damage Ground coffee is being used not beans and the appliance does not deliv er the coffee Too much ground coffee has been added The 06 2 button has not been pressed and the appliance has used both the ground coffee added and the coffee ground by the mill Ground coffee has been added when the appliance is off Remove the infuser and thoroughly clean the inside of the appliance as described in section 16 2 Repeat the operation using a maximum of 1 measuring scoop of ground coffee Thoroughly clean the inside of the appliance as described in section 16 2 Repeat the operation first pressing the 00 44 button as described in section 9 Remove the infuser and thoroughly clean the inside of the appliance as described in section 16 2 Repeat the opera tion but switch the appliance on first Collection SCLUSIVO L 7 The holes in the spouts are clogged Scrape the holes with needle see section 16 1 fig 29 The coffee does with dry coffee come out of the spouts The mobile drawer inside the service Thoroughly clean the mobile drawer particularly near the but from around the door is
13. Turn the grinding regulator fig 11 one click toward the number 7 see section 8 Insert the hot water spout press the button and run off water from the spout for a few seconds GROUNDS CONTAINER The grounds container is full or missing Empty the grounds container and clean as described in section 6 note 7 then replace INSERT GROUNDS CONTAINER After cleaning the grounds container has not been replaced Open the service door and insert the grounds container ADD PRE GROUND COFFEE With the function selected the pre ground coffee has not been poured into the funnel Add the ground coffee as described in section 9 FILL GEANS CONTAINER The coffee beans have run out If the coffee grinder is very noisy this means a small stone in the coffee beans has blocked the mill Fill bean container Contact an authorized De Longhi serv ice center DESCALE This indicates the presence of lime scale in the appliance The descaling procedure described in section 17 3 needs to be performed as soon as possible PRESS Y Y After cleaning the infuser has probably been left out of the coffee maker Leave the service door closed and the infuser out of the appliance press the pointed buttons then follow the instructions displayed CLOSE DOOR The service door is open If the service door cannot be closed check that the infuser is inser
14. a copia omaggio della rivista Visita http registration delonghi csservice com Visita www delonghi com per una lista dei centri di servizio a te piu vicini Solo Stati Uniti e Canada ELECTRONIC CHARACTERISTICS CARACT RISTIQUES LECTRIQUES CARACTERISTICAS ELECTRICAS CARATTERISTICHE ELETTRICHE 120V 60HZ 1100W Collection Collection Colleci n Collezione A B CDE F CAPPUCCIN CONTAINE POSITION PLEASE WAIT 12 11 10 Collection SCLUSIVO Coffee has been used to factory test the appliance and it is therefore completely normal for there to be traces of coffee in the mill This appliance is however guaranteed to be new INDEX IMPORTANT SAFEGUARDS score ae 7 Y DESCRIPTION page 5 8 C 8 en 9 4 USING FOR THE FIRST TIME unseren a 9 5 TURNING ON AND PREHEATING area 10 6 PREPARING COFFEE USING COFFEE BEANS AND USEFUL TIPS 10 7 CHANGING THE QUANTITY OF COFFEE IN THE CUP 0 cece eee ence en 12 8 REGULATING THE COF FEEMILL scsi een na een 12 9 PREPARING ESPRESSO COFFEE USING G
15. ange the quantity of coffee or frothed milk delivered automatically into the cup follow the instructions in section 15 13 PREPARING LATTE OR ITALIAN Prepare the appliance as described to make cappuccino Before attaching the milk container to the nozzle move the pointer to position 1 FIG 26 if you want to make a LATTE LATTE button or position 2 fig 20 if you want to make ITALIAN MACCHIATO ITALIAN MACCHIATO button Press the LATTE button fig 27 The button lights up and the appliance displays LATTE MLA CONTAINER POINTER IN POSITION T or Press the ITALIAN MACCHIATO button 28 The button lights up and the appliance displays ITALIAN MACCHIATO CONTAINER POINTER IN POSITION 2 Make sure the pointer on the container lid is positioned on the same number indicated on the display After a few seconds the steamed or frothed milk is delivered from the milk spout into the cup below Delivery stops automatically 14 PREPARING FROTHED OR STEAMED MILK WITHOUT COFFEE To prepare only frothed milk without coffee or only steamed milk without coffee move the pointer on the lid to the desired position 1 2 then press the CAPPUCCINO LATTE or ITALIAN MACCHIATO buttons twice within 2 seconds EN Collection SCLUSIVO 15 CHANGING THE QUANTITY OF COFFEE AND MILK FOR LATTE CAPPUCCINO ITALIAN MACCHIATO The appliance is factory preset to automatically deliver standard quantities of coffee or milk
16. ast This warranty runs for two years 2 from the purchase date found on your receipt and applies only to the orig inal purchaser for use What is not covered by the warranty The warranty does not cover defects or damage of the appliance which result from repairs or alterations to the appliance outside our factory or authorized service centers nor shall it apply to any appliance which has been subject to abuse misuse negligence or accidents Also consequential and incidental damage resulting from the use of this product or arising out of any breach of contract or breach of this warranty are not recoverable under this warranty Some states do not allow the exclusion or limitation of incidental or consequential dam age so the above limitation may not apply to you How do you get service If repairs become necessary see contact information below U S Residents Please contact our toll free hotline at 1 866 Latte Best or log onto our website at www delonghi com For all accessories spare parts or replacement parts please contact our parts division at 1 866 528 8323 Residents of Canada Please contact our toll free hotline at 1 866 Latte Best or 1 866 528 8323 Hours of Operation Monday Friday 8 30am 8pm Saturday amp Sunday 9 00am 5 30pm or log onto our website at www delonghi com Residents of Mexico Please refer to the Limited Warranty statement for Mexico see page 6 Please refer to the back page of the manual for
17. blocked and cannot swing hinges to ensure they are free to swing smoothly service door The milk does not run The intake tube is not inserted or is Insert the intake tube in the rubber washer in the milk con inserted incorrectly tainer lid fig 19 of the milk spout d 9 The milk container lid is dirty Clean the milk lid as described in section 16 3 The milk is not well frothed The milk is not cold enough or is not We recommend using fat free or low fat milk at refrigerator The milk contains bub jow fat fat free temperature about 41 F 5 C If you are still not getting the bles or squirts out of the required results try changing the brand of milk milk spout CLUSIVO Collection E T XI gt Collection SCLUSIVO This warranty applies to Super Automatic Espresso Machines with the De Longhi brand name LIMITED WARRANTY What does the warranty cover We warrant each appliance to be free from defects in material and workmanship Our obligation under this warranty is limited to repair at our factory or authorized service center of any defective parts or part thereof other than parts damaged in transit The repaired or new model will be returned at the company expense This warranty shall apply only if the appliance is used in accordance with the factory directions which accom pany it and on an alternating current AC circuit How long does the coverage l
18. e ae a aria 21 20 PROBLEMS BE RESOLVED BEFORE CALLING THE SERVICE CENTER 22 LIMITED WARRANTY es AAN 24 IMPORTANT SAFEGUARDS When using electrical appliances basic safety precautions should always be followed including the following Read all instructions carefully Make sure the voltage of your electrical system corresponds to the voltage shown on the bottom of the machine Do not touch hot surfaces Use handles or knobs To protect against fire electrical shock and personal injury do not immerse cord plug or appliance in water or other liquid Keep the appliance out of the reach of children and do not leave appliance unattended while in operation Unplug from the outlet when not in use and before cleaning Do not operate with a damaged cord or plug or after the appliance malfunctions or has been damaged in any manner Return the appliance to the nearest authorized service facil ity for examination repair or adjustment The use of accessory attachments not recommended by the manufacturer may result in fire electrical shock or personal injury Do not use outdoors Make sure the power cord does not hang over the edge of the table or counter top to avoid getting accidentally caught or entangled Do not place the appliance or its electrical parts on or near electric stoves cooking surfaces or gas burners Plug cord into the wall outlet To disconnect turn any control to off then remove plug from
19. ery 14 single coffees or 7 doubles the appli ance displays EMPTY GROUNDS CONTAINER and emits a double indicating that the grounds container is full and must be emptied and cleaned Until the grounds container has been cleaned the appliance continues to display the message and cannot make coffee To clean open the service door at the front by pulling the handle fig 13 remove the drip tray fig 14 empty and clean Empty the grounds container and clean thoroughly making sure all residue deposited on the bottom is removed IMPORTANT When removing the drip tray the grounds container MUST be emptied even if it is not completely full If this is not done when making your next coffee the grounds in the container may exceed the maximum level and block the appliance NOTE 8 While the appliance is delivering coffee never remove the water tank If it is removed it will not be possible to make the coffee and the appliance will display GROUNG TOG FINE ADJUST ALL ANG INSERT WATER SPOUT AND PRESS DK To turn the appliance on again you must insert the hot water spout fig 4 press the OK button and run off water from the spout for a few seconds When using the appliance for the first time 4 5 cups of coffee need to be made before the appliance starts to give satisfying results If the appliance malfunctions do not contact the service center right away The problem can almost always be resolved by following the i
20. ever it requires emptying The water tank should also be cleaned regularly The drip tray is fitted with a level indicator red showing the level of water it contains When the indicator starts to become visible a few millimeters under the drip tray the drip tray must emp tied and cleaned Check that the holes in the coffee spout are not blocked To unblock them scrape the dry coffee residues away with a needle fig 29 Clean the nozzle after every use with a sponge as shown in fig 30 16 2 Cleaning the infuser The infuser must be cleaned regularly to avoid the build up of coffee encrustations which could cause mal function Proceed as follows Turn the appliance off by pressing the button fig 6 do not unplug and wait for the display to go off Open the service door fig 13 Remove the drip tray and the grounds container fig 14 and clean the two red release buttons on the infuser and pull it out fig 31 IMPORTANT THE INFUSER CAN ONLY BE REMOVED WHEN THE APPLIANCE IS OFF ATTEMPTING TO REMOVE THE INFUSER WITH THE APPLIANCE ON MAY CAUSE SERIOUS DAMAGE Wash the infuser under running water without using detergents Never wash the infuser in the dishwash er Clean the inside of the appliance thoroughly To remove coffee encrustations from the inside of the appli ance scrape with a plastic or wooden fork then vacuum up the residues with a vacuum cleaner fig 32 Replace
21. fee To make 2 coffees press the two short coffees button V Sor the two long coffees button WP WP To change the quantity of coffee delivered automatically into the cup follow the instructions in sec tion 7 The appliance now grinds the beans and starts brewing the coffee into the cup Once the desired quanti ty has been reached the appliance automatically stops delivering the coffee and ejects the grounds into the coffee grounds container 4 After a few seconds the ready message is displayed again and you can make another coffee 5 To turn the appliance off press the I button Before going off the appliance performs an automatic rinse cycle a little hot water runs out from the spouts and is collected in the drip tray beneath Take care to avoid scalds NOTE 1 f the coffee is delivered a drop at a time or not at all turn the grinding coarseness regulator fig 11 one click toward the number 7 see section 8 Turn one click at a time until the coffee is delivered adequately NOTE 2 f the coffee is delivered too fast and is not creamy enough turn the grinding coarseness regulator fig 11 one click toward the number 1 see section 8 Avoid turning the grinding coarseness regulator excessive ly otherwise when you select 2 cups the coffee may run out in drips Mill should only be adjusted while run ning to prevent jamming NOTE 3 Tips to make hotter coffee When you turn the appliance on if you want to make
22. ic bags polystyrene etc must not be left within reach of children as they may rep resent a hazard Place the appliance on work surface far away from water taps basins and sources of heat After positioning the appliance on the work top leave a space of at least 2 in 5 cm between the sur faces of the appliance and the side and rear walls and at least 8 in 20 cm above the coffee maker Never install the appliance in environments where the temperature may reach freezing or below freezing temperatures the appliance could be damaged if the water freezes Make sure the mains voltage corresponds to the voltage indicated on the appliance rating plate Connect the appliance to a grounded socket with a minimum current rating of 10amps The manufacturer is not liable for possible accidents caused by failure to do so If the power socket does not match the plug on the appliance have the socket replaced with a suitable type by a qualified professional The power cable on this appliance must not be replaced by the user as this operation requires the use of special tools If the cable is damaged or requires replacing contact an authorized service center only to avoid all risks You should personalize water hardness as soon as possible following the instructions in section 17 6 Coffee has been used to factory test the appliance and it is therefore completely normal for there to be traces of coffee in the mill This appliance is h
23. ing on the display to exit programming mode or to change other parameters Note to display the time with the appliance off press any button The time will be displayed for five minutes 17 2 Setting auto start time This function programs the time the appliance will come on automatically and be ready for use Make sure the clock on the appliance is set as described above Press the P button then press the button corresponding to the gt gt symbol flashing on the display repeatedly until the menu arrow is on gt STARTTIMEDD 00 Pressthe 9 button corresponding to the SET symbol flashing on the display to set the auto start time If you hold the button down the time is changed rapidly Press the OK button to confirm the value Press the SET button again and the appliance displays gt AUTO STARTNO Press the 48 button corresponding to the SET symbol flashing on the display to modify the function the appliance displays RUTB STRRT YES SCLUSIVO Collection Press the OK button to activate auto start Press the P button corresponding to the ESC symbol flashing on the display to exit programming mode or to change other parameters NOTE When auto start time is set the symbol 1 appears alongside the time the display 17 3 Descaling Over time the continuous heating up of the water used to make the coffee leads to lime scale building up in the inner circuits of the appliance
24. it 1 click 1 line toward the number 7 speeds up coffee delivery without drips Turning it 1 click toward the number 1 slows down delivery giving a creamier appearance to the coffee These adjustments will only be evident after at least 2 cups of coffee have been brewed The grinding coarseness regulator must only be turned when the coffee mill is running eo A Turn one click toward the number 1 to obtain finer ground coffee 3 slower delivery and a creamier appearance Turn one click toward the number 7 for coarser ground coffee and lt faster delivery not a drop at a time OD 7 N 9 PREPARING ESPRESSO COFFEE WITH GROUND COFFEE INSTEAD OF BEANS Coffee has been used to factory test the appliance and it is therefore completely normal for there to be traces of coffee in the mill This appliance is however guaranteed to be new Select the ground coffee function by pressing the 0m 2 OK button fig 1 repeatedly until READY PRE GROUND COFFEE flashes on the display This disables the coffee mill function Lift the central lid place one level measure of ground coffee in the funnel see fig 15 and proceed as described in section 6 NOTE You can make just one coffee at a time by pressing the V or W button Once the coffee has been delivered go back to making coffee using beans deactivate the ground cof fee function by pressing the 04 2 OK button and the coffee mill is enabled for operati
25. n to confirm the temperature selected Press the P button corresponding to the ESC symbol flashing on the display to exit programming mode or gt to change other parameters 17 5 Changing the length of time the appliance remains on The appliance is factory preset to go off automatically one hour after the last coffee has been made The number of hours the appliance remains on max 3 can be increased as follows Press the P button then press the 4 button corresponding to the gt symbol flashing on the display repeatedly until the menu arrow is on gt OFFAFTERTHOUR the 8 button corresponding to the SET symbol flashing on the display to change the number of hours the appliance remains on Press the OK button to confirm the value Press the P button corresponding to the ESC symbol flashing on the display to exit programming mode or gt to change other parameters 17 6 Setting water hardness The descale message is displayed after the appliance has been operated for a factory set period of time calcu lated on the basis of the maximum quantity of lime scale which may be contained in the water used If necessary this period of operation can be extended making descaling less frequent by programming the appliance based on the actual lime content in the water used Proceed as follows Remove the Total Hardness Test strip enclosed on page 2 from its packaging then dip it fully in the water f
26. ng mode or to change other parameters The appliance is now reset to the factory default settings and the READY message is displayed 17 8 Beep ON OFF activates and deactivates the beep Press the P button then press the 4 button corresponding to the 7 symbol flashing on the display repeatedly until the menu arrow is on gt BEEPON Press the A button corresponding to the SET symbol flashing on the display and the appliance will dis play BEEPOFF Press the OK button to turn the beep off Press the P button corresponding to the ESC symbol flashing on the display to exit programming mode or to change other parameters The appliance is now set not to emit any beeps and displays the message READY 18 CHANGING THE LANGUAGE To change the language press the OK button for at least 5 seconds until the appliance displays the installation message in various languages Select the required language and press OK for 3 seconds as described in sec tion 4 1 EN gt Collection SCLUSIVO 19 TROUBLESHOOTING MESSAGE FILL TANK MEANING The water tank is empty or is positioned incorrectly The tank is dirty or encrusted with lime scale WHAT TO DO Fill the water tank as described in sec tion 4 and insert it fully Rinse or descale the tank GROUND TOO FINE ADJUST LL AND INSERT WATER SPOUT AND PRESS The coffee runs off too slowly The appliance cannot make coffee
27. nstructions indicated in sections 19 and 20 If this is not the case or for further explanations contact customer service by calling the number listed in the warranty or visit www delonghi com for a list of service centers near you U S and Canada only 7 CHANGING THE QUANTITY OF COFFEE IN THE CUP The appliance is factory preset to automatically deliver the following quantities of coffee short coffee when the Sbutton is pressed long coffee when the W button is pressed two short coffees when the V V button is pressed two long coffees when the WF WEbutton is pressed To change these quantities proceed as follows Press the button qz or w or Z or W W corresponding to the quantity you want to change for at least 8 seconds then release until the message PROGRAM QUANTITY is displayed and coffee is delivered When the coffee in the cup reaches the required level press the same button again to memorize the new amount The appliance emits a double beep to confirm The appliance is now re programmed with the new settings and displays READY 8 REGULATING THE COFFEE MILL The coffee grinder is preset in the factory to prepare coffee correctly and should not require regulating initial ly However after making the first coffees if you find that coffee delivery is either too fast or too slow in drips the grinding coarseness regulator can be adjusted fig 11 Turning
28. on again NOTE 1 Never add the ground coffee when the appliance is off to avoid IL being dispersed inside the appli ance NOTE 2 Never add more than one level measured scoop otherwise either the appli ance will not make the coffee and the ground coffee will be lost inside the appliance dirtying it or the coffee will run off in drips and the message LESS COFFEE will be dis played NOTE 3 When measuring the quantity of coffee to be added use the measuring scoop supplied only gt Collection SCLUSIVO NOTE 4 Use ground coffee for espresso coffee makers only Do not use coffee beans freeze dried coffee or other materials that could damage the appliance NOTE 5 If you add more than one measure of ground coffee and the funnel blocks use a knife to push the cof fee down fig 16 then remove and clean the infuser and appliance as described in section 16 2 Cleaning the infuser 10 PRODUCING HOT WATER Always make sure the appliance is ready Make sure the water spout is attached to the nozzle fig 4 Position a container under the spout fig 3 Press the 9 button fig 17 The appliance displays HOT WATER and hot water is delivered from the water spout into the container below you should not run off hot water for more than two minutes at a time To stop the flow press the button Once the set quantity of hot water has been reached delivery stops automatically 11 CHANG
29. or a few seconds and remove After about a minute 1 2 3 or 4 red squares develop Press the P button then press the 28 button corresponding to the flashing gt symbol on the display repeatedly until the menu arrow is on gt WATER HARDNESS Y Press the A button corresponding to the SET symbol flashing on the display repeatedly until the num ber coincides with the number of red squares on the test strip for example if there are 3 red squares on the test strip press the button until WATER HARDNESS 3 is displayed Press the OK button to confirm the value The coffee maker is now programmed to provide the descaling warning when necessary based on the actual hardness of the water Press the P button corresponding to the ESC symbol flashing on the display to exit programming mode or to change other parameters 17 7 Resetting factory default settings Ifyou change the original values the factory default values can be reset as follows Press the P button then press the 5 button corresponding to the symbol flashing on the display repeatedly until the menu arrow is on gt RESET TODEFAULT NG Press the 3 button corresponding to the SET symbol flashing on the display and the appliance dis plays RESET DEFAULT YES SCLUSIVO Collection Press the OK button to reset the factory default values Press the P button corresponding to the ESC symbol flashing on the display to exit programmi
30. owever guaranteed to be new To learn how to operate the appliance correctly when you use it for the first time follow the step by step instructions given in the following sections 4 USING FOR THE FIRST TIME 1 The first time you use the appliance select the language To set English plug the appliance into the outlet and wait for the appliance to display PRESS TO INSTRLL ENGLISH Press the OK button fig 1 for at least three seconds until you hear a BEEP and the display shows ENGLISHINSTALLED The appliance then displays the setting message in English If you select the wrong language by mistake follow the instructions in section 18 to choose the right one 2 After 5 seconds the appliance displays FILL To fill remove the water tank fig 2 rinse and fill with fresh water Never exceed the MAX line Put the water tank back and push as far as it will go 3 Place a cup under the hot water spout fig 3 If the water spout is not in place INSERT WATER SPOUT is dis played Attach it as shown in figure 4 making sure the arrow on the spout is lined up with the arrow on the control panel of the appliance fig 4 The appliance now displays PRESS 0 4 Press the OK button fig 1 A little water will run from the spout running water stops automatically 5 The appliance now displays TURNING OFF PLERSE WAIT and it goes off 6 Fill the container with coffee beans fig 5 being ca
31. r spout fig 21 and attach the milk container to the nozzle You will hear a fig 22 Position the milk tube as shown fig 23 and then place a sufficiently large cup under the coffee and milk spouts Press the CAPPUCCINO button fig 24 The button lights up and the appliance displays CAPPUCCINO CONTAINER POINTER IN POSITION 2 Make sure the pointer on the container lid is positioned on the same number indicated on the display After a few seconds the frothed milk is delivered from the milk spout into the cup below Milk delivery stops automatically then the coffee is delivered SCLUSIVO Collection 5 EN wu NOTE 1 While preparing the cappuccino milk or coffee delivery can be interrupted pressing the CAP PUCCINO button NOTE 2 If you run out of milk while delivering frothed milk remove the container and refill it Then put it back in place and press the CAPPUCCINO button to request a cappuccino again NOTE 3 To ensure the milk frother is absolutely clean and hygienic after making cappuccinos clean the chan nels inside the milk container lid Place a cup under the milk spout Press the CLEAN button on the milk container lid and hold down for at least 8 seconds fig 25 The appli ance displays CLEANING After cleaning is complete remove the milk container and place in the refrigerator You should not leave the milk outside the refrigerator for more than 15 minutes NOTE 4 To ch
32. reful not to exceed the MAX line IMPORTANT To prevent malfunction never fill with ground coffee freeze dried coffee caramelized beans or anything else which could damage the appliance L 7 5 TURNING AND 1 Press the button fig 6 The appliance displays HERTINGUP PLEASE WAIT to indicate preheating is underway 2 Once preheating is completed the appliance displays RINSING PLEASE WAIT and performs an automatic rinse cycle a little hot water runs from the spouts and is collected in the drip tray below Tip If you want a short coffee less than 2 oz to make it hotter fill the cup with this hot rinsing water first Leave it for a few seconds then empty it to preheat the cup 3 The appliance now displays the ready message READY REGULAR TASTE 6 PREPARING COFFEE USING COFFEE BEANS AND USEFUL TIPS 1 The appliance is preset to make coffee with a regular taste You can also choose coffee with a mild extra mild strong or extra strong taste To choose the required taste press the 0 2 OK button fig 1 The selected coffee taste will be displayed 2 Place 1 cup under the spouts to make 1 short coffee fig 7 or 2 cups for 2 short coffees fig 8 For a creami er coffee lower the spouts to bring them as close to the cups as possible fig 9 3 Press one of the coffee buttons fig 10 the S button to make a short coffee or the W button for a long cof
33. ted cor rectly section 16 2 note 1 INSERT WATER SPOUT The button has been pressed and the hot water spout has not been insert ed Insert the hot water spout fig 4 INSERTINFUSER ASSEMBLY After cleaning the infuser has probably been left out of the coffee maker Insert the infuser see section 16 2 LESS COFFEE The ground coffee funnel is clogged Too many coffee beans or too much ground coffee has been added Empty the funnel with the help of a knife as described in section 9 note 5 fig 16 Select a milder taste or reduce the quan tity of ground coffee then press or wo WE Wo deliver the coffee again GENERIC ALARM The inside of the appliance is very dirty Clean the inside of the appliance thor oughly as described in section 16 2 If the message is still displayed after clean ing contact a service center SCHUSVO Collection E 20 PROBLEMS RESOLVED BEFORE CALLING THE SERVICE CENTER Ifthe appliance is not working the causes of the malfunction can be identified and resolved by referring to sec tion 19 If on the other hand a general alarm is on run the following checks before calling the service center PROBLEM The coffee is not hot The coffee is not creamy enough The coffee runs out too slowly CAUSE The cups have not been preheated The infuser is too cold The coffee is ground too coarsely
34. ution from inside the appli ance Proceed as follows Empty the water tank rinse and fill with clean water Reposition the tank Empty the full container and then put it back under the hot water spout Press the OK button Hot water will run off from the spout into the container below and the appliance dis plays RINSING When the water tank is empty the appliance displays the message RINSING COMPLETE PRESS OK Press the OK button and refill the water tank with clean water The descale program is now terminated and the appliance is ready to make coffee again Collection SCLUSIVO NOTE If the descaling cycle is interrupted before completion the appliance continues to display the descale message and the program must be started again from the beginning Empty the water tank rinse fill with clean water and run off a cup of hot water IMPORTANT FAILURE TO DESCALE THE APPLIANCE REGULARLY INVALIDATES THE WARRANTY 17 4 Changing coffee temperature To change the temperature of the coffee proceed as follows Press the P button then press the lt button corresponding to the gt symbol flashing on the display repeatedly until the menu arrow is on gt HIGH TEMPERATURE Press the 8 button corresponding to the SET symbol flashing on the display until the appliance dis plays the required coffee temperature Note To obtain hotter coffee see also section 6 note 3 page 10 Press the OK butto
35. utton to enter the appliance menu ESC but X Control panel ton to exit menu 2 SAFETY WARNINGS READ THESE INSTRUCTIONS CAREFULLY AND KEEP FOR FUTURE CONSULTATION This appliance is designed to make espresso coffee and hot drinks Use with care to avoid scalds from the water or steam jets or through incorrect use This appliance is intended for domestic use only Any other use is considered improper and thus danger ous The manufacturer is not liable for damages caused by improper incorrect or unreasonable use of the appli ance When using the appliance do not touch the hot surfaces Use handles or knobs Do not touch the appliance with damp hands or feet Do nat allow children or infirmed persons to use the appliance unsupervised Never allow children to play with the appliance In the event of failure or malfunction unplug the appliance from the outlet and do not tamper with it in any way If it requires repair contact an authorized service center only and ask for original spare parts to be used Failure to respect the above could reduce the safety of the appliance If the power cable is damaged it must be replaced by the manufacturer or by the authorized service cen ter to avoid all risks EN Collection SCLUSIVO 3 INSTALLATION After removing the packaging make sure the product is complete and undamaged If in doubt do not use the appliance and contact a qualified professional Packing elements plast
36. wall outlet Do not use the appliance for other than the intended use This appliance is to be utilized for domestic use only The manufacturer declines all responsibility for any damage caused by improper incorrect or irresponsible use WARNING To reduce the risk of fire or electric shock do not remove the cover No user serviceable parts inside Repair should be done by authorized service personnel only SAVE THESE INSTRUCTIONS THIS APPLIANCE IS FOR HOUSEHOLD USE ONLY SHORT CORD INSTRUCTIONS A short power cord is provided to reduce risks resulting from becoming entangled in or tripping over a longer cord Longer detachable power supply cords or extension cords are available and may be used if care is exercised in their use If an extension cord is used the marked electrical rating should be at least as great as the electrical rating of the appliance If the appliance is provided with 3 wire grounding type cord the extension should be a GROUNDING TYPE 3 WIRE CORD The longer cord should be arranged so that it will not drape over the counter top or table top where it can be pulled on by children or tripped over Your product is equipped with a polarized alternating current line plug a plug having one blade wider than the other This plug will fit into the power outlet only one way This is a safety feature If you are unable to insert the plug fully into the outlet try reversing the plug If the plug should still fail to fit
Download Pdf Manuals
Related Search