Dell PP22L Laptop User Manual
Contents
1. Tighten all fluid connections before each use Check the hoses tubes and couplings daily Replace parts immediately if worn damaged or loose Permanently coupled hoses cannot be repaired FIRE AND EXPLOSION HAZARD Improper grounding poor air ventilation open flames or sparks can cause a hazardous condition and result in fire or explosion and serious injury e Ground the equipment personnel in or close to the spray area the object being sprayed and all other electrically conductive objects in the spray area See Grounding on page 5 If there is any static sparking while using the equipment stop spraying immediately Identify and correct the problem Provide fresh air ventilation to avoid the buildup of flammable vapors from the solvent or the fluid being sprayed Do not smoke in the spray area Extinguish all open flames or pilot lights in the spray area Do not turn on or off any light switch in the spray area Electrically disconnect all equipment in the spray area Keep the spray area free of debris including solvent rags and gasoline Do not operate a gasoline engine in the spray area 2 308 845 RA INSTRUCTIONS CO K A WARNING EQUIPMENT MISUSE HAZARD Equipment misuse can cause the equipment to rupture malfunction or start unexpectedly and result in a serious injury This equipment is for professional use only Read all the instruction manuals tags and labels before operating the equip2. 30 31 Part No 239 542 239 561 222 300 224 200 240 421 240 425 100 333 114 369 193 251 193 252 238 909 188 171 113 521 114 456 236 449 236 450 Description GUN Delta Spray air spray Model 240 349 See instruction manual 308 742 GUN Delta Spray HVLP Model 240 350 See instruction manual 308 741 GUN PRO 3500sc electrostatic Model 240 352 See instruction manual 307 912 GUN PRO 4500sc electrostatic Model 240 353 See instruction manual 308 131 HOSE ASSY air spray HVLP 25 ft 7 6 m Delta packages HOSE ASSY PRO gun 25 ft 7 6 m PRO packages SCREW cap hex head FITTING tube quick connect LABEL product Delta packages LABEL product PRO packages GROUND WIRE amp CLAMP ASSY TUBE suction ELBOW street ELBOW street REGULATOR fluid pressure 0 30 psi 0 207 kPa 0 2 bar Model 240 350 See instruction manual 308 325 REGULATOR fluid pressure 0 100 psi 0 0 6 MPa 0 7 bar All Models except 240 350 See instruction manual 308 325 A Extra Warning labels are available for free Qty Parts Drawing Wall Mount Packages with Fluid Pressure Regulators Model No 240 349 Delta Spray air spray package Model No 240 350 Delta Spray HVLP package Model No 240 351 no hoses 31 or gun 30 Model No 240 352 PRO 3500sc electrostatic package Model No 240 353 PRO 4500sc electrostatic package Grounding Detail z 26 8088A 308 845 11
3. STRAINER line _ po a Pp These parts cannot be ordered separately A Extra Warning labels are available for free Parts Drawing Wall Mount Packages with Surge Tanks Model No 240 361 Delta Spray air spray package Model No 240 362 Delta Spray HVLP package Model No 240 363 no hoses 31 or gun 30 Grounding Detail 308 845 13 Accessory Fluid Filter Kit Fluid Filter Kit 240 440 Ref No PartNo Description Qty 101 114 361 FILTER fluid 1 102 113 322 CONNECTOR male 1 103 054 188 TUBE PTFE 3 8 O D 8 in 104 113 534 ELBOW male x female 2 105 111 917 NIPPLE Nylon 1 The Fluid Filter Kit listed above can be installed to filter fluid drawn by the suction tube after it comes out of the pump Install the Fluid Filter Kit as follows see Fig 3 1 Apply thread sealant specified in Fig 3 to all male threads in this kit 2 Remove the elbow 40 from the pump outlet and remove the tube 16 See the Parts drawing on page 11 3 Thread one the elbows 104 into the pump outlet Assemble the nipple 105 and the other elbow 104 5 Thread the nipple 105 with the elbow 104 attached to it into the elbow 104 that you threaded into the pump outlet 6 Thread the fluid filter 101 onto the male threads of the elbow 104 7 Thread the male connector 102 into the fluid filter 101 8 Turn the fluid filter male connector assembly towards the elbow 39
4. This makes connecting the tube 103 in step 9 easier 9 Cutthe PTFE tube 103 to the proper length and install it to run from the male connector 102 to the elbow 39 14 308 845 To avoid sharp bends in the tube you may have to cut it to a shorter length Apply Graco Thread Sealer or Loctite 567 or equiv alent to male threads For initial installation make sure the dome is firmly hand tightened onto the filter body Do not use a tool During subsequent service hand tighten more firmly to prevent drips 103 102 101A 104 Fig 3 oA Technical Data Maximum fluid working pressure 100 psi 0 7 MPa 7 bar Maximum incoming air pressure 100 psi 0 7 MPa 7 bar Maximum operating temperature 120 F 49 C Gun See separate gun instruction manual Pump See separate pump instruction manual Fluid pressure regulator See separate fluid pressure regulator instruction manual Air pressure regulators See separate air pressure regulator instruction manual Wetted parts fluid hoses for Delta guns nylon stainless steel sis Wetted parts fluid hoses for PRO guns nylon nickel chrome plate ss Wetted parts other fluid hoses andtubing nylon PTFE S Wetted parts fluid fittings Ss nylon acetal 304 316 stainlesssteel Weight without hoses or gun packages with fluid pressure regulator Approx 29 Ib 13 kg packages with surge tank Approx 27 12 kg Sound data Sound power
5. and respirator e Ifthe pump diaphragm fails hazardous fluid may be exhausted along with the air 308 845 3 Setup This equipment is compatible with most water based materials See the wetted parts in the Technical Data section and your fluid and solvent manufacturer s compatibility information Do not use acid catalyzed materials they are incom patible with the acetal used in this pump A WARNING e TOXIC FLUID HAZARD gt Hazardous fluid or toxic fumes can cause serious injury or death if splashed in the eyes or on the skin inhaled or swallowed e Read TOXIC FLUID HAZARD on page 3 e Use fluids and solvents that are compatible with the equipment wetted parts Refer to the Tech nical Data section of all equipment manuals Read the fluid and solvent manufacturer s warnings General Information e Always use Genuine Graco Parts and Accessories available from your Graco distributor See the Product Data Sheet for this package Form No 305 898 If you supply your own accessories be sure they are adequately sized and pressure rated for your system e Reference numbers and letters in parentheses refer to the callouts in the figures and the parts lists on pages 10 and 12 4 308 845 Preparing the Operator Anybody who operates this system should be trained in the safe efficient operation of all system components At a minimum all operators should thoroughly read the safety setup and ope
6. INSTRUCTIONS PARTS LIST gt 308 845 Rev C This manual contains important GRACO qe warnin nd information arnings and informatio First choice when READ AND KEEP FOR REFERENCE quality counts INSTRUCTIONS ACETAL HUSKY 307 WALL MOUNT PUMP DRUM SUCTION PRO Delta Spray Packages Metal fluid fittings and hose couplings are stainless steel l This manual contains 100 psi 0 7 MPa 7 bar Maximum Fluid Working Pressure nae not included 100 psi 0 7 MPa 7 bar Maximum Air Inlet Pressure throughout the contents Please see the second Packages with Fluid Pressure Regulators gt page of this book page 1A Model No 240 349 Sy for a description of the with hoses and Delta Spray air spray gun revisions and additions Model No 240 350 with hoses and Delta Spray HVLP gun Model No 240 351 no hoses or gun Model No 240 352 with hoses and PRO 3500sc electrostatic gun Model No 240 353 with hoses and PRO 4500sc electrostatic gun Packages with Surge Tanks Model No 240 361 with hoses and Delta Spray air spray gun Model No 240 362 with hoses and Delta Spray HVLP gun Model No 240 363 no hoses or gun CES This gun and hose for PRO 3500sc This gun and hose for Delta Spray Air Spray Electrostatic package package or Delta Spray HVLP package GRACO INC P O BOX 1441 MINNEAPOLIS MN 55440 1441 Graco Inc is registered to I S EN ISO 9001 Instruction Manual Pa
7. Model No 240 362 Delta Spray HVLP package Parts List Wall Mount Packages with Surge Tanks Model No 240 361 Delta Spray air spray package Model No 240 363 no hoses 31 or gun 30 Ref No Part No 1 240 210 3 106 285 5 104 123 6 102 025 7 188 089 8 D31 331 9 054 139 10 111 864 11 188 181 12 111 276 13 111 863 15 054 175 16 054 188 17 188 285 19 112 899 20 112 903 21 114 370 24 104 119 12 308 845 Description SHIELD ASSY front Qty Contains 1a to 1h shown in Fig 2 on page 9 BOLT U WASHER spring lock NUT hex NIPPLE PUMP Husky 307 See instruction manual 308 553 TUBE flexible CONNECTOR male PLUG bung airtight SCREW thumb CONNECTION union HOSE Nylon TUBE PTFE BRACKET wall WASHER lock NUT hex FITTING tube quick connect SCREW cap hex head BAD 1 75 in Ref No Part No 25 192 996 26 104 029 27 054 139 294A 189 220 30 239 542 239 561 31 240 421 32 100 333 33 114 369 34 193 253 37 238 909 38 188 171 40 114 456 50 111 911 Description Qty SHIELD back 1 LUG grounding 1 TUBE Nylon 11 5 in LABEL warning 1 GUN Delta Spray air spray Model 240 361 See instruction manual 308 742 1 GUN Delta Spray HVLP Model 240 362 See instruction manual 308 741 HOSE ASSY air spray HVLP 25 ft 7 6 m SCREW cap hex head FITTING tube quick connect LABEL product GROUND WIRE amp CLAMP ASSY TUBE suction ELBOW street
8. OSION Screw the bung plug R into the drum bung opening HAZARD on page 2 Adjust the suction tube L so the end of the tube is Kea about 1 2 in 13 mm off the bottom of the drum and e Pump One end of the ground wire is already secure the suction tube using the thumbscrew on the connected to the pump grounding strip Connect bung plug the clamp end of the ground wire to a true earth ground Hose Connections e Air compressor Follow the manufacturer s recommendations This package is shipped with the hoses connected Before you disconnect any hoses make a note of the e i Object being sprayed Follow the local code proper connections e Fluid supply container Follow the local code Flush Pump Before First Use e All solvent pails used when flushing Follow the The pump was tested in water If the test solution local code Use only metal pails which are could contaminate the fluid you are pumping flush the conductive Do not place the pail on a pump thoroughly with a compatible solvent See non conductive surface such as paper or Flushing the System on page 8 cardboard which interrupts the grounding continuity e Systems with PRO 3500sc and PRO 4500sc electrostatic gun Make sure you read all of the grounding instructions and warnings in your gun instruction manual 308 845 5 Operation Using the Gun See the gun instruction manual for gun operation care flushing cleaning and technical data Read the entir
9. antability and fitness for a particular purpose in connection with accessories equipment materials or components sold but not manufactured by Graco These items sold but not manufactured by Graco such as electric motors switches hose etc are subject to the warranty if any of their manufacturer Graco will provide purchaser with reasonable assistance in making any claim for breach of these warranties In no event will Graco be liable for indirect incidental special or consequential damages resulting from Graco supplying equipment hereunder or the furnishing performance or use of any products or other goods sold hereto whether due to a breach of contract breach of warranty the negligence of Graco or otherwise FOR GRACO CANADA CUSTOMERS The parties acknowledge that they have required that the present document as well as all documents notices and legal proceedings entered into given or instituted pursuant hereto or relating directly or indirectly hereto be drawn up in English Les parties reconnaissent avoir convenu que la r daction du pr sente document sera en Anglais ainsi que tous documents avis et proc dures judiciaires ex cut s donn s ou intent s a la suite de ou en rapport directement ou indirectement avec les procedures concern es Graco Phone Number TO PLACE AN ORDER contact your Graco distributor or call this number to identify the distributor closest to you 1 800 367 4023 Toll Free All written and vi
10. e gun manual before operating the sprayer Pressure Relief Procedure See Fig 1 A WARNING The system remains pressurized until pressure is manually relieved To reduce the risk of serious injury from pressurized fluid accidental spray from the gun or splashing of any fluid follow this proce dure whenever you e Stop spraying e Are instructed to relieve pressure e Check or service any system equipment e Install clean or change spray nozzles 1 Turn off the air supply to the pump 2 Be sure the pump air regulator is open by turning the knob E clockwise several turns 3 Open the bleed type master air valve K to relieve pump air pressure 4 Trigger the gun B to relieve fluid pressure in the hoses Adjusting Pump and Gun Air Regulators See Fig 1 NOTE The pump air regulator knob E and gun air regulator knob F have a locking feature To unlock the knobs pull out on them You will feel them click out To lock them at the desired setting push them back into the locked position Always adjust the pump air regulator E and gun air regulator F slowly to prevent surging during startup Turn the knobs clockwise to increase pressure and counterclockwise to decrease air pressure 1 Slowly adjust the pump air regulator E to set air pressure to approximately 60 psi 413 kPa 4 bar 2 If your system has a fluid pressure regulator turn the fluid pressure regulator handle G to adjust the fluid press
11. level at 70 psi 0 48 MPa 4 8 bar and 115 cpm Sound pressure level at 70 psi 0 48 MPa 4 8 bar and 115 com Sound power level was measured per ISO Standard 3744 Dimensions Wall Mounting Hole Layout 9 0 in 229 mm p kat wall view of de 5 0 in mounting bracket 0 in 127 mm 188 285 203 mm p 6 7 in 170 mm Four 0 438 in 11 mm dia holes to mount bracket to wall 0654 308 845 15 Graco Standard Warranty Graco warrants all equipment manufactured by Graco and bearing its name to be free from defects in material and workmanship on the date of sale by an authorized Graco distributor to the original purchaser for use With the exception of any special extended or limited warranty published by Graco Graco will for a period of twelve months from the date of sale repair or replace any part of the equipment determined by Graco to be defective This warranty applies only when the equipment is installed operated and maintained in accordance with Graco s written recommendations This warranty does not cover and Graco shall not be liable for general wear and tear or any malfunction damage or wear caused by faulty installation misapplication abrasion corrosion inadequate or improper maintenance negligence accident tampering or substitution of non Graco component parts Nor shall Graco be liable for malfunction damage or wear caused by the incompatibility of Graco equipment
12. ment Use the equipment only for its intended purpose If you are uncertain about usage call your Graco distributor Do not alter or modify this equipment Use only genuine Graco parts and accessories Check the equipment daily Repair or replace worn or damaged parts immediately Do not exceed the maximum working pressure of the lowest rated system component This pack age has a 100 psi 0 7 MPa 7 bar maximum working pressure Use fluids that are compatible with the equipment wetted parts See the Technical Data section of all the equipment manuals Read the fluid manufacturer s warnings Route the hoses away from traffic areas sharp edges moving parts and hot surfaces Do not expose Graco hoses to temperatures above 180 F 82 C or below 40 F 40 C Do not use the hoses to pull equipment Do not move pressurized equipment Wear hearing protection when operating this equipment Comply with all applicable local state and national fire electrical and other safety regulations TOXIC FLUID HAZARD Hazardous fluids or toxic fumes can cause a serious injury or death if splashed in the eyes or on the skin swallowed or inhaled e Know the specific hazards of the fluid you are using Read the fluid manufacturer s warnings e Store hazardous fluid in an approved container Dispose of the hazardous fluid according to all local state and national guidelines e Wear appropriate protective clothing gloves eyewear
13. ration sections of this manual Preparing the Site e Use acompressor capable of delivering 40 cfm 1 12 m8 and a minimum of 80 psi 552 kPa 5 4 bar for efficient operation e Clear obstacles and debris that could cause an unsafe operating environment e Runa 1 2 in I D air line from your compressed air supply to the pump location Be sure the air is dry and filtered e When the bleed type master air valve K is closed and the pump air regulator is opened it relieves all air pressure to the system components e Ventilate the spray booth A WARNING To prevent hazardous concentrations of toxic and or flammable vapors spray only in a properly ventilated spray booth Never operate the spray gun unless ventilation fans are operating Check and follow all of the national state and local codes regarding air exhaust velocity requirements Setup Assembling the Wall Mount Unit Grounding See Fig 1 Install the wall bracket G 5 ft 1 5 m above the floor A WARNING For proper hole dimensions use the Wall Mounting Hole Layout on page 15 Be sure the wall is strong To reduce the risk of static sparking the entire enough to support the weight of the pump and hoses system must be grounded Check your local any accessories the fluid and stress caused by pump electrical code for detailed grounding instructions operation for your area and type of equipment Ground all of this equipment Also read FIRE AND EXPL
14. re periodic cleaning First relieve the pressure Unscrew the surge tank cover from its base and remove the filter screen Clean the screen with a compatible solvent and reinstall it in the surge tank Make sure you reinstall the cover with a firm hand torque to ensure a good seal A WARNING To reduce the risk of serious injury whenever you are instructed to relieve pressure always follow the Pressure Relief Procedure on page 6 NOTE The pump requires approximately 15 to 20 psi 103 to 138 kPa 1 to 1 4 bar to function This is the lowest fluid pressure available If lower fluid flow is required a smaller fluid tip may be required on the spray device Operation Priming the System See Fig 1 1 Close the gun air regulator F 5 2 If your system has a fluid pressure regulator G close it Slowly open the gun air regulator F and pull the gun trigger just enough to open only the air valve in the gun With the gun air triggered set the gun air pressure to 60 psi 413 kPa 4 bar 6 Hold the gun against and aimed into a grounded 2 Open ihe Diced ype manara valas metal waste pail and fully trigger the gun If your 4 Slowly set the pump air regulator E pressure to sie has a fluid pressure regulator G slowly 20 to 30 psi 140 to 210 kPa 1 4 to 2 1 bar The opent pump cycles quickly then it slows down when it is The gun emits air until the fluid arrives When fluid primed Set the pump air pre
15. rts List Changes This page contains a summary of changes or additions that do not appear in the contents of the manual Improve pressure control instructions Graco Ref 6557 Change 30psi HVLP fluid regulator and gauge to a 60psi gauge and regulator Obsolete suction tube Graco Ref 6557 308845 1A Notes 308845 1B Table of Contents Symbols WarningS 6 0c cece eee eee eee 2 Warning Symbol SClUP eros Perch Garces Ma ee VE se 4 ce N OE A WARNING Parts List and Parts Drawing 240 349 to 240 353 10 This symbol alerts you to the possibility of serious 240 361 and 240 363 12 injury or death if you do not follow the instructions Fluid Filter Kit 240 440 00 14 Technical Data s cancevewad Asters 15 Caution Symbol DIMENSIONS r ieren e a eE i eee 15 Wall Mounting Hole Layout 15 A CAUTION Graco Standard Warranty 16 A CAUTION Graco Phone Number 085 16 This symbol alerts you to the possibility of damage to or destruction of equipment if you do not follow the corresponding instructions A WARNING PRESSURIZED FLUID HAZARD Spray from the gun hose leaks or ruptured components can splash fluid in the eyes or on the skin and cause serious injury Do not stop or deflect fluid leaks with your hand glove or rag Follow the Pressure Relief Procedure on page 6 before cleaning checking or servicing the equipment
16. sconnect the pump air hose from the pump air regulator 2 Disconnect the gun air hose from the gun air regulator 3 Loosen but do not remove the two front pump foot screws 24 4 Loosen but do not remove the two top shield screws 32 5 If your system has a fluid pressure regulator 50 make sure the T handle is horizontal 6 Pull the front shield assembly free of the system 1c p 7 i S gun air ih regulator O pump air S ce regulator Front Shield Assembly Orderable Parts Ref No PartNo Description Qty la 192 995 SHIELD front 1 1b 111 804 REGULATOR air See instruction manual 308 167 2 1c 160 430 GAUGE pressure 2 1d 114 362 VALVE ball 1 le 159 840 ADAPTER 2 1f 188 077 NIPPLE 1 1g 114 369 FITTING tube 1 th 114 370 FITTING tube 1 Fig 2 8263A Back Shield 25 1 Disconnect the gun fluid hose from the fluid pressure regulator nipple 28 or surge tank nipple 7 2 Disconnect the hose 16 that runs from the fluid pressure regulator or surge tank 50 to the elbow 40 on the pump outlet 3 Loosen but do not remove the two top shield screws 32 4 Loosen but do not remove the two back pump foot screws 24 5 Pull the back shield free of the system The fluid pressure regulator or surge tank 50 stays mounted to the back shield Gauge Lense Covers Clear stick on peel off lense covers are available for the gauges These covers protect the gauge len
17. ses from spray When they get too dirty to read the gauges they can be peeled off discarded and replaced Order as follows 240 441 for 2 5 inch gauges package of 25 sheets 12 lense covers to a sheet 240 442 for 2 inch gauges package of 25 sheets 12 lense covers to a sheet 308 845 9 Model No 240 349 Model No 240 350 Model No 240 351 Model No 240 352 Model No 240 353 Ref No Part No 1 240 210 2 110 789 3 100 014 5 104 123 6 102 025 7 192 994 8 D31 331 9 054 139 10 111 864 11 188 181 12 111 276 13 111 863 15 054 175 16 054 188 17 188 285 19 112 899 20 112 903 21 114 370 24 104 119 25 192 996 26 104 029 27 054 139 28 189 436 294 189 220 10 308 845 Parts List Wall Mount Packages with Fluid Pressure Regulators Delta Spray air spray package Delta Spray HVLP package no hoses 31 or gun 30 Description SHIELD ASSY front Contains 1a to 1h shown in Fig 2 on page 9 WASHER flat SCREW WASHER spring lock NUT hex HANDLE shield PUMP Husky 307 See instruction manual 308 553 TUBE flexible 75 CONNECTOR male PLUG bung airtight SCREW thumb CONNECTION union HOSE Nylon 10 TUBE PTFE BRACKET wall WASHER lock NUT hex FITTING tube quick connect SCREW cap hex head SHIELD back LUG grounding TUBE Nylon NIPPLE LABEL warning PRO 3500sc electrostatic package PRO 4500sc electrostatic package Qty A ANN gt 1 in Ref No
18. ssure to 40 psi 280 flows freely release the gun trigger kPa 2 8 bar Delta Spray KEY regulated Air Spray package or eet 307 pump regulated HVLP package shown C Gun fluid hose D Gun air hose E Pump air regulator F Gun air regulator B G Fluid pressure regulator H Pump ground wire K Bleed type master air valve L Suction tube M Front shield assembly aT N Back shield P AN P Lifting hande G Q Wall bracket R Bung plug L 8120A Fig 1 308 845 7 Operation When to Shut Down the System Shut down the system at the end of the work shift and before checking adjusting cleaning or repairing the system Always relieve the pressure A WARNING To reduce the risk of serious injury whenever you are instructed to relieve pressure always follow the Pressure Relief Procedure on page 6 Flushing the System Flush the system at the following times e Before the first time use e When changing colors e Before fluid can dry or settle out in a dormant system e Before storing the system Flush the system as follows See Fig 1 1 Relieve the pressure A WARNING To reduce the risk of serious injury whenever you are instructed to relieve pressure always follow the Pressure Relief Procedure on page 6 2 Remove the gun air cap before flushing and clean it separately 3 Place the suction tube into a grounded metal pail of compatible sol
19. sual data contained in this document reflects the latest product information available at the time of publication Graco reserves the right to make changes at any time without notice Sales Offices Minneapolis Detroit Foreign Offices Belgium Korea Hong Kong Japan GRACO INC P O BOX 1441 MINNEAPOLIS MN 55440 1441 http www graco com 1998 Graco Inc 308845 Rev C January 2000 PRINTED IN U S A 16 308845
20. ure to 40 to 60 psi 276 to 413 kPa 2 8 to 4 bar 6 308 845 3 Slowly open the gun air regulator F and pull the gun trigger just enough to open only the air valve in the gun With the gun air triggered set the gun air pressure to 60 psi 413 kPa 4 bar NOTE Gun air pressure higher than 60 psi 413 kPa 4 bar will cause excessive overspray and lowered efficiency 4 If your system has a fluid pressure regulator G fully trigger the gun and fine tune the fluid pressure to obtain the desired atomization Systems with Fluid Pressure Regulator See Fig 1 With the fluid pressure regulator G you can control fluid pressure from the pump to the gun For an accurate setting adjust the fluid regulator only when the gun is triggered and fluid is flowing through the regulator Be sure the jam nut under the T handle G does not interfere with your adjustments Tighten the jam nut to lock in the setting if desired 1 To open the fluid regulator which allows fluid to flow turn the T hand clockwise 2 Toclose the fluid regulator which restricts or shuts off the fluid flow turn the T handle counterclockwise Systems with Surge Tank See Parts Drawing on page 13 In systems with a surge tank 30 the fluid pressure is the same as the air pressure applied to the pump pump has 1 1 ratio of fluid to air Adjust the fluid pressure as required with the pump air regulator E The surge tank filter screen may requi
21. vent 8 308 845 4 Make sure the air regulators E and F are closed NOTE The gun air regulator F always stays closed during flushing 5 Open the bleed type master air valve K 6 Slowly open the pump air regulator E until the pump starts 7 Hold the gun against a grounded metal waste pail and fully trigger the gun If your system has a fluid pressure regulator G slowly open it until the fluid flows smoothly 8 When solvent appears release the gun trigger 9 Fora first time flush trigger the gun and flush with solvent for 30 seconds For flushing after spraying fluid trigger the gun and flush with solvent until the system is thoroughly cleaned 10 Repeat the procedure with clean solvent if needed 11 Lift the fluid intake tube from the fluid supply and trigger the gun and run the pump until air comes from the gun 12 Relieve the pressure The system is now ready to be stored or primed with another fluid See Priming the System on page 7 Maintenance See the separate component instruction manuals for individual component maintenance procedures Access to some system components requires that you remove the shields The following steps are for shield removal Shield replacement is the reverse of these steps so make sure you take notes on the proper hose connections Depending on your system see the Parts Drawings on pages 11 and 13 for number call outs Front Shield Assembly 1 1 Di
22. with structures accessories equipment or materials not supplied by Graco or the improper design manufacture installation operation or maintenance of structures accessories equipment or materials not supplied by Graco This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of the claimed defect If the claimed defect is verified Graco will repair or replace free of charge any defective parts The equipment will be returned to the original purchaser transportation prepaid If inspection of the equipment does not disclose any defect in material or workmanship repairs will be made at a reasonable charge which charges may include the costs of parts labor and transportation THIS WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ANY OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE Graco s sole obligation and buyer s sole remedy for any breach of warranty shall be as set forth above The buyer agrees that no other remedy including but not limited to incidental or consequential damages for lost profits lost sales injury to person or property or any other incidental or consequential loss shall be available Any action for breach of warranty must be brought within two 2 years of the date of sale Graco makes no warranty and disclaims all implied warranties of merch
Download Pdf Manuals
Related Search