Daewoo DWF-5510 Washer User Manual
Contents
1. Connector S Hose gt Connector For the opposite end connect it to water inlet as the above procedure Leak Test Turn on the water completely to check for any leakage If any leakage turn off the water try again as the above procedures For the special tap call a qualified plumber for the installation 6 DRAIN HOSE SETTING Before operating your washer install drain hose properly First connect the drain hose to the drain outlet at the rear side of your washer and then fasten it tightly with the hose clamp Next the other end of drain hose set as the below Pump Model Connect the drain hose to the drain outlet at the rear side of the washing machine and fasten it tightly with the clamp supplied Attach the hose guide included in the accessory kit to guide the drain hose over the tub or standpipe s PULL HOSE THROUGH Hook the drain hose to the edge of the tub paying attention that there are no bends or constractions along the drain hose J Or connect the drain hose to a standpie of a diameter greater than that of the drain hose and at a height of min 70cm Attach the hose guide included in the accessory kit to guide the drain hose over the tub or standpipe ventilated NOTES 1 Let the highest point of the drain hose be more than 1m above the floor If not so the water in the washer could be drained du2. a container under the filter to collect water FILTER CONTAINER Turn the cap counter clockwise LJ Pull out the filter assembly off the case of the main body Clean the drain filter removing the foreign stuffs Put in the filter along the guiding prominence of the case Please note the left position of the filter adjusting the groove to the Turn the cap clockwise tightly SPECIAL GUIDES FOR REMOVING STAINS Stained heavily soiled or greasy items may need to be prewashed or soaked for best results Soaking helps remove protein type stains like blood milk or grass Prewashing helps loosen soil before washing Stain removal rules e Use warm water for soaking or prewashing stained laundry Hot water can set stains e Most stains are easier to remove when they are fresh Old or set stains may not coconut e Before treating any stain find out what kind of stain it is how old the stain is what kind of fabric it is and if the fabric is colorfast Check the care label e Washing and drying can set some stains e Start with cold or warm water hot water can set some stain e When bleach is recommended use a bleach that is safe for the fabric e Put the stained area face down on a paper towel or white cloth Apply the stain remover to the back of the stain This forces the stain off fabric instead of through it Stain removal
3. guide STAIN TO REMOVE Rinse immediately in COLD water Blood If stain remains soak in cold water with an enzyme prewash Use ice in plastic bag to harden the gum Chewing gum Scrape off what you can and then sponge with white spirits Cocoa Chocolate Sponge with COLD water and soak in an enzyme prewash If stains persist rub in a little detergent and rinse in cold water Blot up quickly and rinse out in COLD water Coffee Rub in a little detergent and wash in the maximum temperature allowed for the fabric type Cream Milk Rinse in COLD water and wash normally Ice cream If stain is still apparent sponge with white spirits Rub affected area with white vinegar and then rinse under running COLD water Deodorant Sponge with white spirits Treat stiffened areas with enzyme prewash Egg Soak in a COLD enzyme prewash rinse and wash normal Fabric Softener Rub affected area with bar soap and wash normally Treat as soon as pressible by sponging with COLD water Fruit stains Rub a little detergent on the stain and wash normally Grass Sponge with white sprites Rub in an enzyme prewash and wash as normal Grease and oil Lay the affected area face down on an absorbent cloth and work from the back Sponge with white spirits or dry cleaning fluid Wash normally Iron or rust Apply lemon juice and salt and place in the sun Wash normally Lipstick Sponge with white methylated spirits
4. supply cord e Unplug the power supply cord Non use or vacation care Operate your washer only when you are at home If will be on vacation or not using your washer for an extended period of time you should e Unplug the power supply cord or turn off eletrical power to the washer e Turn off the water supply to the washer This helps avoid accidental flooding due to a water pressure surge while you are away 15 Cleaning the Lint Filter Pull the Filter frame up ward Turn the lint filter inside out wash to the lint off with water Filter Frame Lint Filfer Return the filter as it was and insert the filter frame into the slot Cleaning the water inlet filter e Clean the filter when water leaks from the water inlet Pull the power Turn off the water plug out before supply to the out cleaning it washer and sperate the inlet hose a Pull the inlet filter T Remove the dirt from the inlet filter with a brush P Cleaning the drain filter e In case U shape drain hose this filters equipped at the cack side of washer e This drain filter is to screen the foreign stuffs such as threads coins pins buttons etc e If the drain filter is not cleaned at proper time every 10 times of use Drain problem could be caused see page Put down the remained water in the hose And put
5. DAEWOO INSTRUCTION MANUAL TABLE OF CONTENTS m SAFETY INSTRUCTIONS amp SPECIFICATIONS PE e eee 2 a PARTS DESCRIPTIONS T r eee 3 DIRECTONSFORSAEFEWUSET 4 cn 9 il gS Fe E T T 4 eWaten COnnmeclonicc cts cccccaeceeiernesnn 6 DramiHOSe Seting cee 7 BOW TC OPERATE eer 8 PreparationmionNashin o cre creer estes eee 8 e Descriptions of Control Panel 00 9 e General Procedures for Operation 10 e Guides for Basic Washing Programs 11 e Guides for Other Useful Programs 18 m PERIODIC MAINTENANCE n se 14 m SPECIAL GUIDES FOR REMOVING STAINS 16 m TROUBLE SHOOTING GUIDEG ly X PLEASE READ CAREFULLY THIS INSTRUCTION MANUAL BEFORE USING YOUR WASHER AND SAVE THIS FOR FUTURE REFERENCE Model DWF 5510 SAFETY INSTRUCTIONS amp SPECIFICATIONS SAFETY INSTRUCTIONS x Your safety is important to us gt Read all instructions before using your washer t Do not wash items cleaned washed soaked in or spotted with wax paint gasoline oil or other flammable fluids The fumes can create a fire hazard or explosion t Flammable fluids dry cleaning solvents kerosene gasoline etc should not be used or stored in or near your washer Do not add flammable fluids to your wash water These substances give off vapors that can create a fire hazard or explosion t Do not allow children to operate play with or crawl on or inside your washer Supervise child
6. and wash normally Wash in WARM water and detergent Mildew Moisten area with lemon juice dry in the sun and wash normally If stain persists and the fabric allows use a bleach Mud Brush off any dry mud Rinse in cold water If stain persists rub in a little detergent and wash normally Paint oil based Scrape off any fresh paint and sponge with a non flammable dry cleaning fluid and wash normally Paint water based Scorch marks Treat while still wet rinse in WARM water and wash normally Dampen a cloth with hydrogen peroxide lay it over the affected area and press with a fairly hot iron 17 TROUBLE SHOOTING GUIDES Most problems are easily solved if you understand the cause Check the following list for problem befor calling for service Before calling for service check these PROBLEM CHECK POINT e The washer will not e Is there a power failure operate at all e Is the power cord correctly connected to an electric outlet e Is the electric fuse broken e Did you turn on the power e Did you press Start Hold button e Is there correct amount of water in the tub e Water is not supplied e Did you connect the inlet hose and open the water tap I water supply is not finished within 30 e Is the inlet hose or the water tap frozen minutes the lamp EEJ willightup andthe ls the water supply shut off buzzer will sound to indicate a problem e Does foreign matter block up the inlet h
7. ener on the load e The dispenser is for liquid fabric softener use only Softener inlet Symbol 4 Close the washer lid door 5 Press the power button 6 Select the course The full automatic course has four settings FUZZY LIGHT HEAVY SUIT See page 9 7 Press the START HOLD button 11 GUIDES FOR BASIC WASHING PROGRAMS Fuzzy Course e This course is a washing method for the general clothes except the extraordinary clothes such as blanket wool etc Put in the clothes Press the power switch Press the Start Hold button and close the lid Light Course e This course is effective for the washing of light clothes or lightly stained clothes e Regulate the water level according to the wash load Press the power Press the course Select the water Press the switch selection button level proper to the Start Hold button for LIGHT wash load and close the lid O Fuzzy LIGHT Cae mip O HEAVY OLow O wooL Heavy Course e This selection is effective for blue jean climbing clothes ruck sack sports wear Press the power Press the course Select the water Press the switch selection button level proper to the Start Hold button for HEAVY wash load and close the lid O Fuzzy O HIGH O LIGHT mip HEAVY OLow O WOOL SUIT 12 Wool Course Option e This selection is effective fo
8. g with Display for remaining time 3 Signal Buzzer for the Operation of Control Button Coin Filter Only in Pump Model identified with P added to Model No e g DWF 5510NP x The above specifications and features are subject to change without prior notice 2 PARTS DESCRIPTIONS DETERGENT CASE Symbol FABRIC SOFTNER INLET Symbol See page 10 LIQUID BLEACH INLET Symbol See page 10 CONTROL PANEL 88 display and some buttons may be excluded WASH TUB PULSATOR BASE Height is optional WATER CONNECTOR ce Blue Color Cold Pink Color Hot DOOR DRAIN HOSE LINT FILTER PLUG GROUND WIRE This will not be provided in case of 3 wire power cord ADJUSTABLE LEG Optional The drawings in this book may vary from your washer model They are designed to show the different features of all models covered by this book Your model may not include all features ACCESSORIES Dryten option Hose Adapter Under Cover option Hose Clamp NU Drain In case of screw shaped inlet hoses water tap adapters will not be provided Inlet Hose option Non Pump Model Pump Model co DIRECTIONS FOR SAFE USE HOW TO INSTALL Location Place your washer on a level and solid floor considering the length of inlet hose drain hose and power supply cord If washer is not level it should be corrected by the adjustable leg p
9. he procedure selection button But wool suit course can not reservation Press reservation button until the digital monitor displays the finishing time you want Press Start Hold to start 14 PERIODIC MAINTENANCE Proper care of your washer can extend its life This section explains how to care for your washer properly and safely Cleaning your washer Exterior Interior Wipe up detergent bleach and other spills Clean interior with 250ml of chlorine bleach with a soft damp cloth or sponge as they mixed with 500ml of detergent occur occasionally wipe the outside of the Run washer through a complete cycle washer to keep it looking like new Repeat process if necessary Do not put sharp or metal object in your washer they can damage the finish Check all pockets for pins clips money bolts nuts etc Do not lay these objects on your washer after emptying pockets Winter storage or moving care Install and store your washer where it will not freeze Because some water may stay in the hoses freezing can damage your washer If storing or moving your washer during freezing weather winterize it To winterize washer To use washer again e Shut off water faucet e Flush water pipes and hoses e Disconnect and drain water inlet hoses e Recombination water inlet hoses e Run washer on a drain and spin setting e Turn on water faucet see page 13 for 1 minute e Recombination power
10. m button until the indicaing lamps make the combinations you want If only spin lamp is turned on that means you will operate your washer for spin only If rinse and spin lamp are turned on that means you will operate your washer for rinse and spin If add lamp is turned on with other process lamps that means the time of the corresponding process will increase by 1 2 minutes that is if add is on with wash rinse and spin the time of each process will increase by 1 2 minutes Wash add 2 min Rinse add 1 min Spin add 1 min step 3 Press water level selector as your decision step 4 Press Start Hold to start Selecting Water level Pressing the Power Switch Selecting Course Wash amp Rinse amp Spin Only Spin OADD O WASH O RINSE O SPIN Add amp Wash Add amp Rinse amp Spin Add amp Spin Add amp Wash amp Rinse amp Spin Only Wash Rinse amp Spin OADD wasH RINSE SPIN OADD O WASH O RINSE sPiIN ADD wasH O RINSE O SPIN ADD O WASH RINSE sPiN ADD O WASH O RINSE sPiN ADD wasH RINSE sPiN OADD wasH O RINSE O SPIN OADD O WASH RINSE sPiIN Pressing the Start Hold Switch End of Washing It is Informed by buzzer For the reservation of finishing time Set your program as the above procedure remaining last step Press the course selection button Press t
11. nect the Ground Wire to Such a Thing e Never connect it to a gas pipe because of danger e Never connect it to a telephone wire or a lightning of a explosion rod because of os very dangerous at a thunderbolt Gas Pipe Telephone Wire WATER CONNECTION Be careful not to confuse hot water inlet pink color and cold water inlet blue color if your washer is provided with dual water inlets Also if you have only one water tap connect the inlet hose with cold water inlet blue color For normal tap Pull down the collar of the inlet hose to separate it from the hose adapter Loosen the four screws properly in fitting into water tap Fit the hose adapter into the water tap and tighten the four screws evenly while pushing up the adapter so that the rubber packing can stick to the water tap tightly SS lt TAPE Remove the tape and screw connector B into connector A tightly Connector A Connector B Connect the inlet hose to the hose adapter pulling down the collar of hose end Connect the opposite end of the hose to water inlet of your washer tightly e Please check the rubber packing is inside the hose end In case that your washer is not provided with collar compartment procedure and is not necessary For Thread Fitting Type Connect the inlet hose to the thread of water tap or water pipe by tightening aa
12. nly be replaced by a repair shop appointed by manufacturer because special purpose tools are required 18
13. ose filter e The washer will not drain Is the drain hose frozen or blocked up by dirt If the drain is not finished within selected Is the drain hose kinked or deformed time lamp FEF willight up and the buzzer _ S the end of the drain hose immersed in water will sound to indicate a problem e Is there excessive dirt inside the pump housing e The washer will not spin Is the clothe in the tub collected on one side e Is the washing machine installed on an uneven floor or is the If the clothes is collected on one side during vibration serious spin and the tub becomes unbalanced the e Is the lid open spin operation will be interrupted and then ree F this unbalanced condition will be corrected The lamp Bd will light up in this case by following operation WATER SUPPLY gt RINSE DRAIN However if the unbalanced condition is unchanged despite repeating the above operation the lamp B will ight up and the buzzer will sound to indicate a problem e These cases are not malfunctions e The sound wing heard during water supply is the operating sound made by the water inlet valve e The sound sha heard in stopping the tub is the sound that comes from the autobalancer of the tub e The sound wung heard during wash or spin is the operating sound made by the air bubble generator NOTE Please check the point before calling for a service If the supply cord is damaged it must o
14. r wool clothes 1 2kg s limitation for 1 time wash e Do not put leather clothes or chamois clothes into the washing tub for washing It may cause shrinkage or deformation to the clothes e Please use the neutral detergents only e The water temperature is fixed to COLD e The water level LOW is not select Press the course selection button for WOOL Press the power switch O Fuzzy O LIGHT O HEAVY WooL Select the water level proper to the wash load O HIGH mib OLow Press the Start Hold button and close the lid Suit Course Option e This selection is effective for High quality sweater wool etc 1kg s limitation for 1 time wash Press the power switch Press the course selection button e Put in the wash market with for SUIT Dry Cleaning O Fuzzy e Use detergent that is Only for Dry Cleaning OLIGHT e The water temperature is fixed to COLD O HEAVY e The water level LOW is not select suiT Select the water Press the Put the clothes into Press the level proper to the Start Hold button the tub after the Start Hold button wash load and close the lid buzzer sounds and close the lid O HIGH mib OLow GUIDES FOR OTHER USEFUL PROGRAMS For the partial process or the combinations or for adding time of each process step 1 Press power switch step 2 Press progra
15. ren closely when your washer is used near them t Do not reach into the wash tub unless START HOLD button is pressed and all motion stops while spinning t Do not use chlorine bleach and ammonia or acids such as vinegar or rust remover in the same wash Hazardous fumes can form ts Unplug power supply cord before attempting to service your washer t Do not pour water on the control panel t Remove foreign objects such as coin pin knife other metallic materials etc inside your wash load They may damage any fabric t Do not overload your washer to avoid poor cleaning wrinkling and or any abnormal operation SPECIFICATIONS MODEL NO DWF 5510 Power Source Please refer to the rating label at the back of your washer Power Consumption 250W Width X Depth mm 532 X 542 Height mm 855 Net Weight Kg 32 Maximum Mass of Textile 5 5kg Material of Internal Tub Recyclable Poly Propylene Water Consumption Approx 135 Liters Cycle Washing Capacity Please refer to the rating label at the back of your washer Washing Program 4 Programs Water Level High 55 Liters Medium 45 Liters Low 31 Liters Direction of Inlet Valve Backward Operating Water Pressure 0 3Kgf cm 8Kgf cm 2 94N cm 78 4N cm Pulsator Provided with 6 Spouting Holes for Powerful Upward Water Stream 1 Air Bubble Generator Optional Features 2 Reserved Washin
16. ring operation 2 Be sure that the height of the drain hose must be less than 1 4m above the floor If not so the wart in the washer could not drain 3 The hose guide MUST be fitted to the drain hose The drain hose should not extend more than 55mm from the end of the hose guide This is to prevent SYPHONING If necessary the drain hose can be trimmed to length Non Pump Model In case that it goes over a door sill Don t let the height of the drain hose exceed 20cm from the ground In case of extending the drain hose Don t let the total length exceed 3m 3 Be careful that the end of the drain hose is not immersed in water 3m HOW TO OPERATE PREQARATION FOR WASHING To obtain the best washing results you must operate your washer properly This section give you this important information Preparing clothes for washing e Close zippers snaps and hooks to avoid snagging other items Remove pins buckles and other hard objects to avoid scratching the washer interior Empty pockets and turn them inside out e Turn down cuffs and turn synthetic knits out to avoid pilling e Tie strings and sashes so they will not tangle e Treat spoats and stains see Special Guides for Removing stains on page Sorting washed together Separate heavily soiled items from lightly soiled ones even if they would normally be Separate dark colors f
17. rom light colors colorfast items from non colorfast item Loading Drop items into washer loosely Items should move easily through wash water for best cleaning and wrinkle free results Load washer properly and select correct load size setting Overloading and selecting a setting too small for the wash load can cause poor cleaning increase wrinkling create excessive lint wear out items faster because of pilling e Mix large and small items in each load Load evenly to maintain washer balance An off balance load can make the washer vibrate during spin e Reduce wash time when using a small load size setting Loads with only a few small items need less wash time e Use a large load size setting to reduce wrinkling with permanent press clothes and some synthetic knits These items should have more room to move in the water than heavy items towels jeans DESCRIPTIONS OF CONTROL PANEL DWF 5510 Power Switch e Press this button to turn the power ON or OFF Water Level Selector e This button is used to select the water level you want Reservation Button e If you want to reserve the finishing time of washing use this button As this button is pressed digit in display increases by 1 hour at one press e If current time is 8 00 am and you expect washing will be completed around 5 00 pm press this nine times in order to display 9 Course Selector e This button i
18. rovided optionally in the front right side under the base and or a thin block or brick Do not place or store your washer below 0 C 32 F to avoid NOTES any damage from freezing The opening muse not be obstructed by carpeting when Do not place your washer where it may be splashed during the washing machine is installed on a carpeted floor bathing Installation of the Under Base Cover Option eer After installing the washing machine assemble DWF 5510 the under base cover Before installing your washer remove the Push the under base cover into the end pad from the bottom of the cabinet which decrease the noise made by this Then separate under cover from rear side washer of cabinet by unscrewing and insert it into the base Power Supply Before plugging the plug into wall receptacle check the voltage rating is in the range of rating marked on the label at the back side of your washer Grounding e If your water tap or water pipe e If both your water tap and e In case of using 3 core cord is not made of metal connect water pipe are made of metal there is no need for the ground wire to a copper connect the ground wire to the grounding plate or a metal rod and bury base of the water tap it in the earth 4 20Cm e It is of no use connecting the ground wire to the water pipe made of plastic Never Con
19. s used to select the washing course according to the type of wash loads Either Wool or Suit course is adopted to your Washing Machine Program Button e With this button you can create new programs by combinations of process Temperature Selector Optional e If your washer is connected to two water taps for cold water and hot water you can select them Without operation cold water would be selected automatically 0000 0 Start Hold e With this button you can make your washer proceed your program or stop temporarily And you can also release the temporary stop by pressing this 10 GENERAL PROCEDURES FOR OPERATION 1 Add measured detergent to the washer Follow manufacturer s directions for safe use 2 OPTIONAL STEP If desired add measured liquid chlorine bleach to the bleach inlet use only liquid chlorine in the bleach inlet Follow manufacturer s direction for safe use NOTE S e Do not let bleach splash drip or run down into washer rf basket 6 Undiluted bleach will damage any fabric it to touches e Do not use this dispenser to add powdered chlorine or Bleach inlet color safe bleach to your wash load The dispenser is for Symbol liquid chlorine bleach use only 3 OPTIONAL STEP If desired add measured liquid fabric softener to the softener inlet e Pour liquid fabric softener into the dispenser using the amount recommended on the package Avoid dripping or spilling any fabric soft
Download Pdf Manuals
Related Search