Compaq 900 Computer Monitor User Manual
Contents
1. Pin Assignment Male Mini D 15 Connector Signal 15 Pin Mini D Sub Red Video 1 Green Video 2 Blue Video 3 Horizontal Sync 13 Vertical Sync 14 Ground 4 5 6 7 8 10 11 No Connection 9 SDA DDC 12 SCL DDC 15 14 English appendix Agency Regulatory Notices Federal Communications Commission Notice This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency en ergy and if not installed and used in accordance with the instruc tions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be deter mined by turning the equipment off and on the user is encour aged to try to correct the interference by one or more of the following measures E Reorient or relocate the receiving antenna E Increase the separation between the equipment and the receiver E Connect the equipment into an outlet on a circuit different from that to which the receiver is con nected E Consult the dealer or an experienced radio or televi sion technician for help M2. 2 Push the tilt swivel base firmly toward the front of the monitor until the latches click into the locked position Removing the Tilt Swivel Base 1 Squeeze and hold the latches 2 Pull the tilt swivel base to the rear of the monitor and lift to remove the base English 5 oe INTRODUCTION Feature Highlights Maximum Compatibility e Automatically scans all horizontal frequencies between 30 kHz and 95 kHz and all vertical frequencies between 50 Hz and 160 Hz e Supports multiple operating platforms such as PC compatible or Macintosh computers with optional adapter e Multiple graphic standards with high refresh rates 640 x 480 85 Hz 800 x 600 85 Hz 1024 x 768 85 Hz 1280 x 1024 85 Hz 1600 x 1200 75 Hz e Supports wide range of graphics standards including VGA Super VGA 8514 A XGA Mac II 13 640 x 480 Mac 16 832 x 624 Mac 21 1152 x 870 as well as all VESA standards Latest Screen Technology e Horizontal dot pitch of 0 22 mm High Contrast 19 CRT 48 2 cm for maximum clarity and detailed pictures e Special antireflection antiglare and antistatic coating of the screen face provides better focus contrast and color performance e Flat and square screen reduces image distortion and glare e Full feature digital control and multilingual OSD system allows easy adjustment of geometry and color Furthermore the monitor provides even advanced adjustments lik
3. VESA D PM S Standard H sync V sync Video State o ff On Blank Standby On Of Blank Suspend Of Of Blank Of NUTEK VESA state IED indicator Pow erConsum ption Nom aloperation On Green lt 130W Pow arang Suspend Amber lt 15W Position Al Bower ated Off Amber lt 8W Position A2 According to TCO guidelines the optimum TCO readings are measured when brightness and contrast are adjusted to their center position English 11 800 TROUBLESHOOTING Troubleshooting Before calling the Compaq authorized service center please check that the items below are properly connected or set In case of using a nonstandard signal please check the pin assignments and the signal timing of your adapter with the specifications in the section Pin Assignment Table 1 Screen is blank e Check to see if the monitor is turned on e Check to see if the signal cable and power cable are both connected properly e The monitor may be in an energy saving sleep mode or you may have a screen blanking utility installed Press any key on the keyboard or type your password e Check to see if the horizontal vertical frequency is out of range e Adjust the Brightness and Contrast controls in the OSD 2 No Signal Input is displayed on the screen e Check to see if the video card is seated correctly in its slot e Check to see if the computer is turned on e Check to see if the signal cable is connected to the video card
4. CONTROLS AND ADJUSTMENTS Controls and Adjustments Once you have installed the monitor for your system please read the instructions in this section which give you some guidelines on how to use the monitor more efficiently It leads you through the various functions of the user controls and explains how to adjust the monitor to your personal preference Front User Controls 0 0000 MENU CONTROL EXIT 1 MENU KEY Displays and selects the Status Position Size Geometry Moire Color and Language functions 2 CONTROL KEYS eAdjusts the parameter of the selected function eAdjusts the contrast or brightness level of the screen 3 EXIT DEGAUSS SWITCH Exits OSD window or manually degausses the monitor 4 POWER LED INDICATOR As long as the monitor is powered this indicator is lit In normal operation it lights green While in power saving mode the indicator will turn to amber 5 POWER SWITCH Turns the monitor On and Off Power Save Note This monitor is equipped with automatic power saving circuitry design that will work with any computer following the VESA DPMS detection format and it meets ENERGY STAR low power state definition When the monitor is first powered on the power save function remains inactive the power save function is triggered when the input signal is cut off by the computer or there is a loss of signal input 8 English CONTROLS AND ADJU
5. a English 17
6. in the computer 3 Display image is not centered or is too small or too large e Adjust the Position and Size controls in the OSD 4 Scrolling or unstable image e Check to see if the signal cable is attached to the computer e Check the pin assignments and signal timings of the monitor and video card 5 Picture is fuzzy e Adjust the Brightness and Contrast controls in the OSD e Push the Degauss button once CAUTION Do not press the Degauss button more than once every 20 minutes when not switching between modes Do not hold the button down continuously 6 Picture bounces or wave patterns are present on the screen e Relocate electrical devices that may be causing electrical interference e See the FCC information in the front of this manual 7 Display edges are curved inward or outward e Adjust the Pincushion control 8 Colors are blotchy e Press the Degauss button once 9 No Plug amp Play functionality Check to see if the host system is Plug amp Play compatible e Check to see if the VGA card is DDC1 DDC2B compatible e Check to see if Microsoft Windows 95 is installed and the software key for DDC function is enabled e Check to see if the manufacturer s original detachable signal cable is being used 12 English Specifications Color Picture Tube Horizontal Dot Pitch Input Signal Scan Frequency Display Area Max Resolution Display Colors Video Bandwidth Misconvergence Plug amp Play Power Supply Po
7. COMPAQ 7 User s Guide Compaq S900 Color Monitor 4 1 d 7 ka pr h Notice The information in this guide is subject to change without notice COMPAQ COMPUTER CORPORATION SHALL NOT BE LIABLE FOR TECHNICAL OR EDITORIAL ERRORS OR OMISSIONS CONTAINED HEREIN NOR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE FURNISHING PERFORMANCE OR USE OF THIS MATERIAL This guide contains information protected by copyright No part of this guide may be photocopied or reproduced in any form without prior written consent from Compaq Computer Corporation 1998 Compaq Computer Corporation All rights reserved Printed in Taiwan Compaq and Deskpro are registered in the U S Patent and Trademark Office Microsoft MS DOS Windows Windows NT and other names of Microsoft products referenced herein are trademarks or registered trademarks of Microsoft Corporation ENERGY STAR is a U S registered mark Product names mentioned herein may be trademarks and or registered trademarks of their respective companies The software described in this guide is furnished under a license agreement or nondisclosure agreement The software may be used or copied only in accordance with the terms of the agreement User s Guide Compaq S900 Color Monitor Second Edition September 1998 Part Number 360564 002 Compaq Computer Corporation ENGLISH TABLE OF CONTENTS SAFETY INSTRUCTIONS occ cecessceceseccccesssosesarsceseestsscccccence
8. STMENTS 1 Press the MENU key to open the On Screen menu function Seven adjustment functions will appear on the On Screen menu Press the MENU key to scroll selections from top down sequence Press A or w to activate the preferred adjustments 0000 er MENU CONTROL EXT A STATUS To display existing timing data of resolution and frequency 2 To recall the factory settings of position size and geometry e Press the key to select Recall e Press the key to execute or press the key to cancel the instruction 1 Press the or key to reposition the display to the right or left 2 Press the A key to move the entire picture upwards and y to move it downwards 1 Press the or key to enlarge or reduce the horizontal O width a0 Aa y 2 Press the A key to enlarge the vertical size or wW to reduce it 1 Press the wW or A key to select Sidepin Balance Keystone Parallel or Rotate 2 Press the or key to adjust the picture according to your preferences 1 Press the w or a key to select the H Moire or V Moire 2 Press the key to proceed 3 Press the or key for preferred picture English 9 CONTROLS AND ADJUSTMENTS F COLOR 1 By pressing the w key you can select modes 1 2 3 or 4 The settings of modes 1 2 and 3 are fixed Only mode 4 can be adjusted by the user 2 To adjust the settings of m
9. ccarsesteereeecsaratensczerseste 2 INTRODUCTION siesiccsccecsesecesesctsncscscaetcesescacececsescncececestttesusastnasstaczertess cecececsetcestcte 4 Package Contents ccicicccciesciedeiecsdtcescdecetcisesietsteseravsesesciesecaatevtenssniatsis 5 Installing or Removing the Tilt Swivel Base u mm nanana nanaawawaawawan 5 Feature MIG MMIQUNS siciccccccesacescesceatsceddeecestieceserececeasrescra ivicceaesenessereieesi lt de 6 Maximum Compatibility aa 6 Latest Screen Technology cccececececseseeceseeseeeeeieeeeeseeeeeeseeaees 6 Ergonomics Information ccceccccceeeeseeeeeeeeeeeeeeeeeeaeeeeetesaeeeeeees 6 Instant Power Saving Solution sseseeeeeeeieeeeieierrirrererrsrerenenren 6 Recommended Use of the Monitor ssssusssussusunsnunsnnunnnnunnnunnununnunnnnnnnnas 7 Master Power Reset Switch sssususunsusunsununsununnununununnununnununnnnnnnnnnnnnnnna 7 CONTROLS AND ADJUSTMENTS nnssasssssnnunsnnnnnnunnnnunnnnunnnnunnnnannnunnnnunnnnnnnnnnnnnnan 8 Front User Gon OS ccsiececscciecesssscensesescscesesssetex KAKANAN GAAN 8 1 Menu Ka 9 2 Contrast Brightness uu mn nananana nwnwawaununananaunanananannannananananaananana 10 Energy Declaration a aanib a NA NANBARAR ANA 11 TROUBLESHOOTING kama RAITENADIINEN NAA 12 TECHNICAL INFORMATION csssscsscsesseesesseeeseeseseeeeeeeeesseseneeeeeneteneeseeeees 13 NT PLUG AA 13 Compatibility daku NANANA ANSNAAA Ka 14 Pin Assignment si
10. e trapezoid parallelogram side pin pin balance moire and rotation that allow the user to fine tune the screen image Ergonomics Information e Electric and magnetic field emissions are kept low to meet the Swedish MPR Il standard or TCO 95 e Front user controls allow easy access and comfort to adjust the screen image to your personal preferences e Horizontal and vertical full scan capabilities allow you to use the entire screen area in most resolutions e A tilt swivel base for horizontal and vertical adjustments always provides the optimum viewing angle Instant Power Saving Solution e The monitor is compatible with VESA DPMS Display Power Management Signaling standard which provides four power saving modes by detecting horizontal and vertical sync signals e The monitor consumes 65 W to 130 W depending on the screen contents in normal operation when a power saving mode is activated it consumes less than 15 W in Standby mode less than 15 W in the Suspend mode and less than 8 W in the Off mode 6 English oe INTRODUCTION Recommended Use of the Monitor When setting up and using the monitor pay special attention to the following for optimum performance Do not use your monitor against a bright background or where sunlight or other light sources will shine directly on the screen The monitor should be placed just below eye level 10 15 for optimum viewing Set the monitor s brightness to match the ambient room l
11. essen anneanne saas eaaa aa na Eaa S 14 Appendix Agency Regulatory Notices ssssussusunsnnunsnnnsununnnnunnnnunnnnunnnnnnnnunnnnnnnnnnnn 15 English 1 SAFETY INSTRUCTIONS 1 Carefully read all of the instructions below and keep the manual for later use 2 Please install the swivel base onto this product before using it 3 The voltage ratings and the rated frequency are on the overlay centered at rear side of this product Do not connect with any source of other voltage or frequency and please follow all warnings and instructions marked on the product 4 Unplug this product from the wall outlet before cleaning and use a damp cloth to clean it Do not use liquid cleaners or aerosol cleaners 5 Do not expose this product to rain or moisture 6 Do not place this product on an unstable cart stand or table The product may fall causing serious damage to the product 7 Do not block or cover ventilating openings with cloth or other material Neither should this product be placed near or over a radiator or a heat register nor should the product be placed in a built in installation unless proper ventilation is provided 8 This product is equipped with a 3 wire grounding type plug This plug will only fit into a grounding type power outlet This is a safety feature If you are unable to insert the plug into the outlet contact your electrician to replace your obsolete outlet Do not defeat the safety purpose of the ground
12. id color graphics with a maximum resolution up to 1600 x 1200 pixels Furthermore it supports VESA 85Hz modes to provide a flicker free display The full function digital control and On Screen Display OSD system provide easy adjustment of image geometry and color settings for different display modes with the precision of a fixed frequency monitor The design of the monitor is also ergonomically concerned In addition to the friendly controls and user comfort features the emission level of the electric and magnetic fields is kept low to meet the Swedish MPR Il standards or TCO 95 optional The monitor is also equipped with energy saving functions It is compatible with the VESA power saving standards The lowest power consumption is less than 8 Watts 4 English INTRODUCTION Package Contents The following lists all of the items included in the monitor package box Please save the original box and packing materials for future transportation or shipment of the monitor Front View Rear View User s Manual TO USERS Many i COMPAQ S909 MONTOR Power Cord O Installing or Removing the Tilt Swivel Base 1 Turn off the system and all attached peripherals 2 Carefully set the monitor upside down Installing the Tilt Swivel Base 1 Align the base with the slots on the bottom of the monitor and insert the tilt swivel base into the slots
13. ight For optimum focus the contrast control should not be set to the maximum level unless the input signal level is extremely low Also the brightness control should be set to a point where the overall background area just begins to disappear Allow adequate ventilation around the monitor so that the heat from the monitor can properly dissipate Neither the monitor itself nor any other heavy objects should rest on the power cord Damage to the power cord can cause fire or electrical shock Keep the monitor away from high capacity transformers electrical motors or other strong magnetic fields Your monitor should not be used in damp dusty or dirty areas Handle your monitor with care when transporting it Master Power Reset Switch The black Master Power Reset switch on the left side of the back of the monitor is installed for technician use when the monitor is being serviced Be sure this switch is turned on after you first install the monitor Always leave this Power Reset switch in the ON position Do not use this switch to power on and power off the monitor Use the power switch on the front panel to power on and power off the monitor CAUTION AN Do not scratch or bump the surface of the CRT with a pen a screwdriver etc Clean the CRT surface with a lint free nonabrasive soft cloth and do not use a solution or glass cleaner that contains abra sives alcohol or an alkaline solution such as ammonia English 7
14. ing type plug Choose a Tandem Blade attachment plug configuration power cord for 230V AC input Due to the safety requirements of different areas please select a suitable power cord according to the following rules in addition to the electric rating A Northern America area Please select a UL listed and CSA certified power cord B Germany Please select a VDE certified power cord C Nordic countries Please select a power cord certified by SEMKO NEMKO DEMKO or FIMKO D The other areas Please select a power cord suitable to the local power system and power outlet 2 English oe SAFETY INSTRUCTIONS Usually a suitable power cord is provided by the manufacturer when this product is sold However this product is sometimes resold or transported to another area with a different power system and safety requirements please pay attention to the selection of a suitable power cord The plug on the power cord is intended to serve as the disconnect device therefore the socket outlet should be installed near the equipment and should be easily accessible 9 Do not allow anything to rest on the power cord Do not locate this product where people can walk on the cord 10 Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a risk of fire or electric shock Never spill liquid of any kind on the product 11 Do not attempt to se
15. ode 4 press the A key to select of R G B gain contrast and the key to increase or to decrease its density G LANGUAGE Press the w or A key to select between English German French Spanish or Italian language for the OSD menu H CONTRAST BRIGHTNESS When the OSD menu is switched off proceed as follows to adjust the contrast or brightness a Press the 4 or y key to increase or decrease the brightness level b Press or key to increase or decrease the contrast level of the screen All adjustments except the color adjustment will be automatically saved The menu block will disappear after 20 seconds without any data changing or press the exit key directly 10 English CONTROLS AND ADJUSTMENTS Energy Declaration This monitor is equipped with a function for saving energy which supports the VESA Display Power Management Signaling DPMS standard This means that the monitor must be connected to a computer which also supports the VESA DPMS standard to fulfill the requirements of the NUTEK specification 803299 94 The time settings for switching to a power saving mode are adjusted from the system unit by software From the first indication of inactivity to power saving position A2 the total time must not be set to more than 70 minutes 1 VESA Power Management Proposal 2 Power Consumption 120 230 Vac
16. odifications The FCC requires the user to be notified that any changes or modifica tions made to this device that are not expressly approved by Compaq Computer Corporation may void the user s authority to operate the equipment Cables Connections to this device must be made with shielded cables with metallic RFI EMI connector hoods to maintain compliance with FCC Rules and Regulations English 15 Declaration of Conformity for products marked with the FCC logo United States only This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation For questions regarding your product contact Compaq Computer Corporation P O Box 692000 Mail Stop 530113 Houston Texas 77269 2000 Or call 1 800 652 6672 1 800 OK COMPAQ For questions regarding this FCC declaration contact Compaq Computer Corporation P O Box 692000 Mail Stop 510101 Houston Texas 77269 2000 Or call 281 514 3333 To identify this product refer to the Part Series or Model number found on the product Canadian Notice This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations Avis Canadien Cet appareil num rique de la classe B respecte toutes les exigences du R glement su
17. r le mat riel brouilleur du Canada German Ergonomics Notice Compaq Computers when tested with the Compaq PE1131 Series monitors were evaluated and found compliant to the requirements of ZH 1 618 German Safety Regulations for Display Work Places in the Office Sector 16 English 00 EPA Enercy Star Compliance Monitors that are marked with the ENERGY STAR Logo meet the re quirements of the EPA ENERGY STAR program As an ENERGY STAR Partner Compaq Computer Corporation has determined that this product meets the ENERGY STAR guidelines for energy efficiency Specific details on using the Energy Saving features can be found in the energy saver or power management section of the computer manual European Notice Products with the CE Marking comply with both the EMC Directive 89 336 EEC and the Low Voltage Directive 73 23 EEC issued by the Commission of the European Community Compliance with these directives implies conformity to the following European norms E EN55022 CISPR 22 Radio Frequency Interference E EN50082 1 IEC801 2 IEC801 3 IEC801 4 Elec tromagnetic Immunity E EN60950 IEC950 Product Safety Japanese Notice TORET NURSES A EH ime VCC ok EOS 2 TABIHAN CT LOREN Abe CET Z E ME ELCRETFDN TOEEDIDARF beda VY SITE LC Jnak RIAMSSIAMOITIL LAV ET KAHA SEC EO CIE LUO VS LT FAW Fi RE PA Pan
18. rvice this product yourself as opening or removing covers may expose you to dangerous voltage points or other risk Refer all servicing to your Compaq authorized service personnel 12 Unplug this product from the wall outlet and refer servicing to Compaq authorized service personnel under the following conditions A When the power cord or plug is damaged or frayed B If liquid has been spilled into the product C If the product has been exposed to rain or water D If the product does not operate normally when operating instructions are followed adjust only those controls that are covered by the operating instructions since improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to normal operation E If the product has been dropped or the cabinet has been damaged F If the product exhibits a distinct change in performance indicating a need for service English 3 INTRODUCTION Introduction The monitor is a multiple frequency high resolution color monitor for PC compatible or Macintosh family and workstation systems The monitor is equipped with microprocessor based intelligence and multiple frequency scanning capability allowing it to provide maximum compatibility for various system platforms The monitor uses the latest screen technology including a 0 22 mm horizontal dot pitch High Contrast CRT to display crisp text and viv
19. wer Consumption Dimensions Weight Environment Consideration TECHNICAL INFORMATION 48 2 cm 19 18 viewable screen size diagonal measurement 90 degree deflection High Contrast CRT antiglare antireflection antistatic medium short persistence phosphor dark bulb 0 22 mm High Contrast Video 0 7 Vp p 75 ohm analog positive Sync Separate Sync TTL Level Horizontal Sync positive negative Vertical Sync positive negative Composite Sync TTL Level positive negative Horizontal 30 to 95 kHz automatically Vertical 50 to 160 Hz automatically Horizontal 350 mm adjustable Vertical 260 mm adjustable 1600 x 1200 pixel noninterlaced Analog input unlimited colors 150 MHz Center 0 3 mm Corner 0 4 mm maximum DDC 1 DDC 2B 100 120 VAC 200 240 VAC 50 60 Hz automatically 130W max 18 1 W x 18 2 H x 18 5 D inches 460 W x 461 H x 469 D mm 57 lbs 26 kgs G W 48 4 Ibs 22kgs N W Operating Temperature 0 C to 40 C Humidity 20 to 80 Storage Temperature 20 C to 60 C Humidity 10 to 90 Note Specifications are subject to change without notice English 13 TECHNICAL INFORMATION Compatibility This color monitor supports multiple operating platforms such as PC compatible and Macintosh family computers This section provides you with detailed information on pin assignment of the D Sub connector and the preset timing chart of the prevailing video standards
Download Pdf Manuals
Related Search