Cateye CC-RD100 Car Stereo System User Manual
Contents
1. No contact magnetic sensor 0100 mm 3999 mm Default figure A 2096 mm B 2096 mm Controller Display Sensor Wheel circumference range Working temperature 0 C 40 C 32 F 104 F Dimension Weight 1 53 64 x 1 7 32 x 19 32 46 5 x 31 x 15 mm 0 63 oz 18 g The factory loaded battery life might be shorter than the above mentioned specification The specifications and design are subject to change without notice2. 999 km mile e SET 0 00 23 59 WU ow etes eem Y T m Clock or 1 00 12 59 To Menu START 2096 clock setti DATA RESET RESET 2 9 MODE a MENS Cip t sg 0 2 Pi T T s gt Av c3 Xt A gs abe Ha 2 1 me 4 i To Wn S 1160 0290 4160 0291 1160 0280 1169 9691 1169 6180 1169 9760 1169 9690 Parts Kit Rear long cord Bracket band Wheel Magnet Lithium Battery CR1620 Magnet for Composite Wheel Hi Power Wheel Magnet G9 All Clear SET UP Ell CC RD100 STR CAUTION Do not concentrate on the computer while riding Be sure to ride safely Tighten the dial on the bracket band by hand only Overtightening can damage the screw threads When cutting off the protruding part of the bracket band rounding the edges to prevent injury When using the computer installed on the bracket press the MODE button around the three dots below the screen Pressing hard on other areas can result in malfunction or damage Install the magnet sensor and bracket securely Check these periodically Avoid having the computer in hot direct sunlight for extended periods Do not disassemble the computer When unclipping the computer from the bracket always hold one hand under the computer so as not to drop it Dropping the computer may damage it Never place the computer on a metal surface If you do the cont
3. ENU button to return to the menu loop Odometer Input HOLD the MODE button The digit will flash Press the MODE button to increase the value HOLD the MODE button to shift to the next digit on the left Repeat until the correct odometer is correct Press the MENU button to set and return to the menu loop Kph Mph Hold the MODE button Press the MODE button to switch between kph and mph When the desired speed scale is flashing press the MENU button to set and return to the menu loop Exit the menu loop by pressing the MENU button again For further information see the SETTING MENU CHART Maintenance To clean the computer or accessories use diluted neutral detergent on a soft cloth and then wipe it off with a dry cloth Troubleshooting The MODE button does not work when the computer is mounted on its bracket Check that there is no dirt between the bracket and the computer Wash off the bracket with water to get rid of any dirt and to ensure that the computer slides in and out smoothly Speed and distance are not displayed Touch a metal item against two contact points of the computer several times to create a short circuit while observing the display If a numeric value appears this signifies that the computer is functioning normally Is the clearance between the sensor and magnet too great Does the magnet pass through the sensor line Adjust the positions of the magnet and sensor Is there any foreign matter which would p
4. If trouble occurs during normal use the part of the Computer will be re 29 Kuwazu Higashi Sumiyashizku S 0 5 1705 14th St 115 Boulder 80302 paired or replaced free of charge The service must be performed by CatEye Osaka 546 0041 Japan TRADA Co Ltd To return the product pack it carefully and remember to enclose Attn CATEYE Customer Service Section Phone 303 443 4595 the warranty certificate with instruction for repair Please write or type your Toll Free 800 5CATEYE name and address clearly on the warranty certificate Insurance handling Fax 303 473 0006 E Ore MEDIE and transportation charges to our service shall be borne by person desiring E mail service cateye com Owner s Manual service URL http www cateye com CATEYE LIMITED WARRANTY 2 Year Computer only CAT EYE Service amp Research Address for USA Accessories Attachments and Battery Consumption excluded CATEYE Service and Research Center 0 5 Pat Nos 5236759 6957926 Pat Design Pat Pending Copyright 2006 CATEYE Co Ltd CCRD1W 060228 2 Component name Bracket band Bracket Sensor Max 5 mm Magnet i ot Sensor rubber band x2 Sensor hook Sensor rubber pad x3 Nylon ties x5 You can also use ties to secure the Bracket rubber pad sensor CC RD100 STRADA ee SET UP BEFORE USE __OPERATION FLOW _ SETTING MENU n
5. act points will conduct electricity discharging the battery When cleaning the computer and accessories do not use thinners benzene or alcohol When tightening down the battery cover after replacing the battery make sure that the rubber packing is properly seated to ensure that a waterproof seal is maintained Dispose of used batteries according to local regulations Do not put batteries into mouth If swallowed consult a doctor immediately Correct installation of sensor and magnet Please set the computer up before mounting the bracket sensor on the bike A Attach the magnet so that it passes through the sensor line of the sensor Be sure that the clearance between sensor surface at sensor line and the magnet does not exceed 5 mm Part names MODE button When using the computer installed on the bracket press the three dots just below the screen When using the computer alone press the MODE button on the back directly Current Speed Pace arrow Indicates whether the current speed is faster or slower than the average speed A Faster V Slower Speed unit km h mph Mode symbol Indicates the data currently displayed on the bottom row Elapsed Time Dst Dst 2 Trip Distance Average Speed Mx Maximum Speed Total Distance Clock Wheel size icon GD Battery case cover Contact Before Installation We recommend sliding the computer onto t
6. een press the MENU button with the Measuring screen displayed The settings can be checked and changed on this screen if necessary With the menu screen displayed press and hold the MODE button to change the setting for the display menu If the menu screen is not touched for a minute the Measuring screen reappears The new settings are applied only when the SET button Finishi is pressed Press the MENU button to change any settings after initial set up Press the MODE button to switch between functions displayed in the following order A or B Wheel Size HOLD the MODE button and A or B begins to flash Press the MODE button to switch between the two Pres the MENU button to set and return to the menu loop Tire Circumference Hold the MODE button Find your tire size off the front tire and match to the circumference chart part 3 of SET UP CHART Press the MODE button to increase the value of the flashing digit HOLD the MODE button to shift to the next digit on the left Repeat until tire circumference is correct Press the MENU button to set and return to the menu loop Clock Setting HOLD the MODE button and 24H will flash Press the MODE button to switch between 24H and 12H HOLD the MODE button to set and the Hours will flash Increase the values by pressing the MODE button When the Hour is correct HOLD the MODE button and minutes will begin to flash Increase the value by pressing the MODE button When the time is correct press the M
7. he bracket to Set Up BEFORE mounting the bracket sensor wire to the bike The mode button on the back of the computer can be difficult to press if not mounted Initial Computer Set up Carry out the SET UP procedure corresponding to the bicycle on which the computer is being installed Press the AC button to carry out the settings in to set up the following order Speed unit Tire size Clock Finally press the MENU button to register the setting Select Speed Scale Press the MODE button to switch between kph kilometers and mph miles When the desired speed scale is flashing press the MENU button to set Tire Circumference Find the size of your front tire and match to the tire circumference chart part 3 of SET UP CHART Press the MODE button to increase the value of the flashing digit HOLD the MODE button to shift to the next digit on the left Repeat until finished and then press the MENU button to set the tire circumference Clock Setting HOLD the MODE button for two seconds and 24h will flash Press the MODE button to switch between 12H and 24H HOLD the MODE button for two seconds set and hours begin to flash Increase the value by pressing the MODE button HOLD down the MODE button for two seconds to set and minutes will flash Increase the value for minutes by pressing the MODE button When time is correct press and release the MENU button Initial set up is now complete Starting Stopping measurement This computer is set to aut
8. n Menu Finishi or CB Wheel size icon Current Speed SETTINGS SET QD B 0 0 4 0 200 0 km h Gal 0 0 3 0 125 0 mph st E F000 fq a To Menu SET km h J L t1998 2 RESET 1 0 00 00 9 59 59 Elapsed Time Dst LE ut size SET b MENU To Menu 302088 1s ta Clock Setting GUTE GJETT Gi Tire size L mm 12x1 75 26 x 7 8 27 x 1 1 4 14x 1 50 26 1 59 27 x 1 3 8 Trip Distance 0 00 999 99 km mile aS ae Dst 2 0 00 999 99 EA mam m J I Trip Distance 2 1000 0 9999 9 km mile 18 x 1 50 26 1 3 8 650 x 38B 18 1 75 26 x 1 1 2 100 x 18C 20x 1 75 26 x 1 40 700 x 19 20x 1 3 8 E 26 x 1 50 E 700 x 20 Av Lag 0 0 200 0 km h 22 x 1 3 8 559 286x175 622 700x236 a 22 x 1 172 559 26x1 95 622 700 x 256 24 1 559 26 2 00 622 700 x 8C 130 Average Speed 0 0 125 0 mph 24 x 3 4 Tubular 28 x 2 10 700 x 30C 24 x 1 1 8 559 262125 622 700x 326 REID 25x235 700 Tubular Luz 24x175 559 26x300 622 700x350 Mx 0 4 0 200 0 km h 242 125 27 1 1 8 522 700 x 40 Maximum Speed t 0 3 0 125 0 mph Tire size SET E 2 To Menu 24 x 2 00 27x1 700 x 38C 24h 12h 1023 1 12 Odo 0 0 9999 9 Total Distance 10000 99
9. omatic time mode automatically carries out measurements when the bicycle is in use When the bicycle moves forward the computer will display speed user starts exercising measure ment starts accordingly when the user stops measurement stops While the bicycle is in motion the speed unit icon flashes Switching Computer function Press the MODE button to switch the computer function according to the OPERATION FLOW CHART Measurement of DST 2 Trip Distance 2 starts stops according to the Trip Distance Note however that DST 2 measurement must be reset individually Resetting data 0 reset measurement data display any data other than DST 2 and then press and hold the MODE button f the MODE button is pressed and held with DST 2 displayed DST 2 only is reset The total distance is not reset in either case Power saving function f the computer has not received any signal for an hour power saving mode will activate and only the clock will be displayed Alternatively if the sensor detects a signal or the MODE button is pressed the main display reappears Dual Wheel Size wo wheel sizes and be registered on the computer This is useful when the computer is shared between two bicycles or when different wheel sizes are used on the same bicycle but at different times Use the menu screen to toggle between A and B For further information see the SETTING MENU Changing the computer settings To bring up the menu scr
10. revent a clean contact on the contact points of the computer and or bracket Clean the contact points Check that no wire cable is worn or broken Even with a normal appearance it may be that a wire cable could be damaged broken internally Replace the bracket sensor set No display Is battery in the computer run down Replace battery and press the All Clear button on the back it Then reinitialize the computer according to SET UP procedures 1 to 4 Incorrect data appears Note the total distance if possible Then reinitialize the computer according Press the All Clear button to SET UP procedures 1 to 4 Then enter the total distance previously noted in the SETTING MENU CC RD100 STRADA Replacing the Battery If the display appears faded replace the battery Before removing the old battery note the current total distance Install a new lithium battery CR1620 with the side facing upward Press the All Clear button on the back and follow set up procedures Then reinitialize the computer according to SET UP procedures 1 to 4 Then enter the total distance previously noted via Odo Input in the SETTING MENU Specification Battery Battery Life Lithium Battery CR1620 X 1 Approx 1 year Using the battery for one hour a day the battery life will vary with the conditions of use 4 bit 1 chip microcomputer Crystal controlled oscillator Liquid crystal display
Download Pdf Manuals
Related Search