Cables to Go AVS815 Network Card User Manual
Contents
1. Control elements TX Power Power 0 9 100 CH CH RTN TV CATV TV VIDEO SCAN CH TXA TXD SET VOL FUNC MTS MUTE RECALL for switching the 2 4 GHz wireless transmitter on and off for switching the AVS 850 on and off direct TV channel selection for paging up and down through the cable TV channels for switching back to the channel last selected for switching between TV channels and cable TV channels for switching between cable TV and video input automatic search tuning for TV and cable TV transmitters to start the automatic search tuning press SCAN twice Add or delete cable TV channels To delete a channel select the one you want to delete such as no 30 and press CH 30 CANCEL will appear in the screen Next time you page through the channel no 30 will no longer appear To add a channel again select it directly e g select no 30 by pressing 3 0 Press CH 30 ADD will appear in the display Next time you page through the channel no 30 will be there for setting the 2 4 GHz transmission channel This setting must be the same as the channel in the AVS 840 Power Transmitter TXA Channel 1 TXB Channel 2 TXC Channel 3 TXD Channel 4 for setting the code see Point 6 2 no function for setting the code see Point 6 2 no function no function shows the current mode in the TV channel and wireless channel e g TXA in the television screen 7 B2. red remote control of another piece of video equipment these infra red signals will be passed on via the RX 579 infra red module to the relevant appliance such as a satellite receiver the audio and video signals of which are being transmitted In order to allow this equipment e g the satellite receiver to be controlled via the remote control to select programmes the infra red transmitter on the infra red module must be glued onto the infra red receiver of the equipment that is being remote controlled When it is being glued on attention must be paid to ensuring that the infra red eye of the unit is not completely covered over so as to ensure that direct control with the original remote control unit is still possible The extension module possesses two infra red diodes for controlling two different units e g a satellite received and a video recorder Establish the position of the infra red receiver with the aid of the operating instructions for the unit that is to be controlled if it is not possible to locate it exactly a little trial and error will be necessary You will thus have the possibility of controlling the unit the signals of which are to be transmitted with the standard remote c 23 4 The AVS 850 Power Transmitter AVS 850 Power Transmitter RX 579 infra red module Items included gt Aerial Co axial adapter branch plug Co axial cable Cinch Scart Plug in mains adapter connecting c
3. 0 Power Receiver and press the POWER button Now press POWER and SET simultaneously You have about 30 seconds time for Points 7 and 8 The display on the television screen will now be RF ID ABC ABC represents the code you have now selected Test the connection by pressing POWER you will only see a glittering pattern on the television set Connect the AVS 850 Power Transmitter to the cable TV socket again see Point 7 1 33 8 Operating possibilities Fine tuning the TV AVS 815 Power Transmitter Parallel operation of a number of AVS 815 Power Transmitters The AVS 850 power transmitter is able to transmit AV signals The various different channel settings 1 to 4 enable up to four over a distance of up to 300 metres line of sight Any wall or Power Transmitters to operate in the immediate vicinity of one concrete ceiling will represent a slight obstacle and will thus another reduce the transmission range of the system lt i m RC 815 remote control unit AVS 840 Power Receiver Se eeeerercccccecscccccccsscscccce oj Channel 1 an it 6 RC 815 remote control unit AVS 840 Power Receiver coscocococococosocososoooocooooooo Channel 2 TXC m NEE REES remote gono unt AVS 840 Power Receiver DOC EEE sie Channel 3 em in 123456 AVS 850 Power Transmitter RC 815 remote control unit AVS 840 Power Receiver eccooocococoooococococoo
4. AA CABLE SENDER POWER sender TV AVS815 Thank you very much You have acquired an electronic system of a very high technical standard With the TV AVS 815 Power Transmitter you can transmit colour images with stereo sound through walls and ceilings The greatest possible care is necessary for bringing it into operations and that means studying every point in these operating instructions Please read these operating instructions even if a third party has already installed the system because they contain important information and the basic principles of operation We would not expect any problems to arise with the system but if any should occur please inform the dealer from whom you acquired this device Please keep this instructions ready to hand whenever you may need to consult them 20 Contents Page 1 Safety instructions 22 2 General description 22 3 Transmissions 23 4 The AVS 850 Power Transmitter 24 5 The AVS 840 Power Transmitter 26 6 The RC 815 infra red remote control for the cable tuner 28 7 Bringing into operation 29 7 1 Connecting the AVS 850 29 7 2 Connecting the AVS 840 30 7 3 Adjusting the cable tuner in the AVS 850 32 7 4 Changing the coding of the RC 815 remote control unit 32 8 Operating possibilities 34 9 Rectifying a malfunction 36 10 Technical data 37 21 22 1 Safety instructions IMPORTANT If the system is handled incorrectly there is a risk of injury from electric s
5. able Control elements 24 Items included 1 Power Sender AVS 850 Power Transmitter 1 12 V plug in mains adapter 1 RX 579 infra red module 1 Cinch Scart connecting cable 1 co axial branch plug 1 co axial cable 1 co axial infra red remote control unit for cable tuner 1 aerial adapter Control elements 1 433 MHz aerial Receives the 433 MHz signals of the original remote control unit sent by radio from the AVS 840 Power Transmitter and passes them on to the integrated cable tuner The infra red remote control signals are also passed on via the enclosed infra red module to the connected item such as a video recorder The aerial must be placed upwards when the unit is in operation 2 Socket for RX 579 extension module For connecting the RX 579 extension module which remote controls the transmitter The infra red diode on the extension module must be glued over the infra red eye of the item being controlled Please note Point 3 here 3 Channel switch The channels can either be selected one behind the other 1 2 3 4 1 2 etc or the other way round or set by means of the enclosed infra red remote control unit using the keys TXA TXD see Point 5 4 TV channel selection switch The TV channels can be selected with this switch 5 Mode switch It is possible to switch from TV to cable TV and video input 6 On Off switch This is for switching the video transmitter on and off When the vi
6. deo transmitter is on LED 7 will light up 7 LED display This lights up when the transmitter is in operation 8 Connecting socket for the mains adapter This is for connecting the mains adapter 9 A V cinchinput sockets 1 video 2 audio input sockets for feeding in the transmission signals With adapter cables 2 are included with the system it is possible to connect almost any item of equipment Note for audio transmissions it is usual to use a cinch cinch cable These are readily available in the trade see picture 10 AV cinch output sockets 1 video 2 audio output sockets These transmit the cable channel that has been set or the signal from the video input This depends on the setting of the mode button 5 and the remote control unit see Point 5 11 Aerial input socket for cable television For connection to the cable television socket For connecting use the enclosed adapter and the co axial cable 12 2 4 GHz transmission aerial Transmits the cable or AV signal to the selected channel 25 5 AVS 840 Power Receiver AVS 840 Power Receiver Items included Plug in mains adapter Cinch scart connecting cable Control elements Rear side 26 Items included 1 Power AVS 840 Power Receiver 1 9 V plug in mains adapter 1 Cinch scart connecting cable Control elements 1 A V Cinch output sockets 1 video 2 audio output sockets These take the receiv
7. e goes into audio right and the white one into audio left 3 Set one of the channels 1 to 4 at the channel switch Note If the AVS 850 Power Transmitter and the AVS 840 Power Receiver are to work together they have to be set both at the same wireless channel 4 Insert the mains adapter into a 230 V mains socket and the 9V plug into the socket provided Never use any other mains adapter than this one 5 Switch the Power Receiver on with the On I switch the LED at the front lights up Place the AVS 840 Power Receiver in a favourable position e g on top of the television set NOTE To control the cable tuner in the AVS 850 or the video recorder to which the AVS 850 Power Transmitter is connected point the RC 815 cable tuner remote control unit or use the original remote control unit of the video recorder at the infra red eye of the AVS 840 on the front side Connecting the Power Receiver to a television set with a video recorder If you would like to feed the AV signal into a video recorder connect the AVS 840 Power Receiver to the AV or scart input sockets on the video recorder You can then record the programme that is being received and or watch television at the same time Antenne 31 7 Starting up 7 3 Settings on the cable tuner The settings on the cable tuner are made with the RC 815 infra red remote control unit from the place where the AVS 840 Power Receiver is set u
8. ed signal and feed it into the receiving unit via the appropriate adapter cable With adapter cables 2 cinch scart cables are included with the system it is possible to connect almost any item of equipment Note for audio transmissions it is usual to use a cinch cinch cable These are readily available in the trade see picture 2 Connecting socket for 9 V mains adapter For connecting the 9 V mains adapter 3 On Off switch For switching the video receiver on and off 4 Channel and switch settings The AVS 840 Power Receiver can be operated in one of two ways 1 Permanent reception of a given wireless channel cable TV or video 2 Switching between the pre set wireless channels at pre determined intervals This function is necessary when for instance the Power Receiver is to be used with a number of different wireless monitor cameras with the AVS 850 Power Transmitter 4 1 Channel switch rear side 4 channel switches switches 1 to 4 for setting the wireless reception channel All AVS 840 Power Receiver In this example Channel 2 is activated 4 2 Setting the switch over time Switches 5 and 6 can be used to set the switch over time between the pre set channels Timetable E CH rh 5 6 Time ON ON 8 seconds E i AAP ON OFF 4seconds al er er OFF ON 2 seconds OFF OFF 1 seconds AVS 840 Power Receiver 4 3 Use as receiver without channel switching The same c
9. hannel must be set on the transmitter and the receiver This facility means that up to four systems can be operated independently of one another Alan 5 AVS 840 Power Receiver Example the AVS 840 Power Transmitter is sending the signal via Channel 2 to the AVS 850 Power Receiver 4 4 Use as receiver with channel switching Switches 1 to 4 enable the channels to be set to each of which the system will switch in turn Switches 5 and 6 enable the switch over time to be set p CH T Example the AVS 840 Power Transmitter H is switching at 4 second intervals Ol Q MM 123456 between Channels 1 and 2 4 AVS 840 Power Receiver 5 Aerial for the control channel Transmits the 433 MHz control signals of the original remote control unit 6 Infra red eye This is the point towards which the unit connected to the remote control unit of the AVS 850 Power Transmitter must be pointed 27 6 The infra red remote control unit for the cable tuner General You need the RC 815 remote control unit in order to be able to control the cable tuner integrated into the AVS 850 Power Transmitter The basic code 0000 is set on the remote control unit when it is delivered This code can be changed e g if two parties in one building want to use the AVS 815 Power Transmitter in parallel see more about this under Point 6 4 amp r m as wa T i mn ch a bill 28
10. hock The following instructions must be followed in order to avoid any risk of injury or damage and the operating instructions must also be adhered to It is never allowed to open the plug in mains adapter Only a properly qualified technician is allowed to check and inspect the system The system is only ever to be operated in dry indoor rooms Avoid high atmospheric humidity and extreme ambient temperatures Should any fault occur in the power supply the system should be taken out of operation at once Never replace defective parts with anything other than original spare parts If there is any danger of a thunderstorm it is a good precaution to separate the system from the mains network in order to protect it from lightning The same applies if the system is to be out of action for any length of time Power must be supplied at the correct rating at all times This applies in particular to the operating voltage in the system and the mains adapter If there is ever any malfunction the dealer from whom the system was acquired must be asked to send it back to the manufacturer for inspection 2 General description Correct and proper use The TV AVS 815 Power Transmitter is designed for use in dry indoor rooms The power supply is provided by the mains adapter enclosed with the Transmitter Please only ever use this mains adapter It is not allowed to alter or modify any part of the system The unit is registered as a device that d
11. led RC 815 infra red remote control does not control the AVS 850 Wrong code set Reset the code as described in Point 7 4 36 10 Technical data Power Transmitter TV Set AVS 815 Power Transmitter AVS 850 Operating voltage Transmitter Channel 1 TXA Channel 2 TXB Channel 3 TXC Channel 4 TXD Transmitter output Range Receiver Cable tuner channels VHF low VHF high UHF AV connections Modulation Video input signal Audio input signal Video input impedance Audio input impedance Dimensions W x H x D Weight Mains adapter 12 V DC 4 Channel 2 414 GHz 2 432 GHz 2 450 GHz 2 468 GHz 10 mW up to 300 metres line of sight 433 92 MHz S6 140 25 MHz to e2 48 25 MHz 31 383 25 MHz to s7 147 25 MHz CH 69 855 25 MHz to 32 391 25 MHz 3 cinch sockets 2 audio 1 video FM 1 Vpp type 1 Vpp type 75 Ohm 600 Ohm 195 x 47 x 150 mm 470g AVS 840 Power Receiver Operating voltage Receiver Channel 1 Channel 2 Channel 3 Channel 4 AV connections Video output signal Audio output signal Remote control channel Dimensions W x H x D Weight Mains adapter 9 V DC 4 Channel 2 414 GHz 2 432 GHz 2 450 GHz 2 468 GHz 3 cinch sockets 2 audio 1 video 1 Vpp type 1 Vpp type 433 92 MHz 1 mW transmission output 170 x 40 x 130 mm 270g Right reserved to make modifications 37
12. oes not cause or suffer radio frequency interference it is CE approved and it conforms with the Low Voltage Directory The safety and installation instructions must be observed There shall be no guarantee cover against damage resulting from any failure to observe these operating instructions and no legal liability for any resultant consequential damage General functions With the TV AVS 815 Power Transmitter you can transmit cable television signals and signals from other video equipment such as VCR SAT receivers and video cameras by radio The audio and video signals are transmitted in the 2 4 GHz range by the AVS 815 Power Transmitter to the AVS 840 Power Receiver The maximum line of sight range is 300 metres The cable tuner integrated into the AVS 850 Power Transmitter is controlled by the Power Receiver with the enclosed RC 815 infra red remote control If you point the remote control unit in the direction of the infra red window on the AVS 840 receiver the infra red signals from this remote control unit will be converted into radio signals which will in turn be transmitted in the 433 MHz range to the AVS 850 Power Transmitter Inside the AVS 850 the radio signals are converted back into infra red signals and passed on to the integral cable tuner 3 Transmissions Cabel TV 1st television set 850 Transmitter N yon x ER AVS 840 Receiver 2nd television set SAT TV If you use the infra
13. oococooooo Channel 4 AVS 840 Power Receiver 34 Extension possibilities with the TV AVS 815 Power Transmitter An AVS 815 Power Transmitter TV Set can be extended with a number of AVS 840 Power Receivers Example 1 Power Transmitter to 3 Power Receivers TXA Ss RC 815 remote control unit 4 Y x F cH T mee aes E l s a Men WETTEN 123456 123456 123456 AVS 840 Power Receiver AVS 840 Power Receiver AVS 840 Power Receiver 35 9 Rectifying a malfunction Problem Remedy Poor transmission quality Reflections of the signal can sometimes affect the transmission quality Move the Power Transmitter or Receiver away just a few inches and this should solve the problem Change the channel settings 1 to 4 on the Power Transmitter and the Power Receiver No transmission Is the same transmission channel 1 to 4 set on the Power Transmitter and on the Power Receiver Is the transmission distance too great Reduce the distance between the Power Transmitter and the Power Receiver The range is up to 300 metres line of sight but walls and ceilings reduce it Have you used the right scart cable Remote control channel If you operate wireless headphones or a similar wireless transmitter on the same frequency as the AVS 815 this can severely reduce its range Is the RX cable inserted into the AVS 850 and glued over the infra red eye of the unit that is being control
14. p 7 4 Changing the coding of the RC 815 remote control unit Note it is only necessary to change the code of the RC 815 remote control unit if another TV AVS 815 Power Transmitter is being operated Note the TV AVS 815 Power Transmitter has two separate television programme memories one for TV channels and the other for cable TV channels You have to do a separate search tuning scan for each level Switch on the television set to which the AVS 840 is connected and select the video input AV in your immediate neighbourhood within about 300 metres The basic setting for the code is 000 To operate the TV AVS 815 Power Transmitter you need the RC 815 infra red remote control unit included with the system To avoid switching your neighbour s Power Transmitter TV on and off you can set a code 2 Switch on the AVS 850 Power Transmitter and the AVS 840 Power on the RC 815 remote control unit and at the Receiver AVS 850 Power Transmitter 3 The television set will display RF ID OOO 4 Press the Power button to switch on the AVS 850 Power Transmitter Please proceed as follows 5 Select the TV CATV button with the level TV 1 Connect the AVS 840 Power Receiver to 6 Press the SCAN button and the TV will display PROGRAMME the television set to which the cable signal PRESS SCAN AGAIN so press SCAN again within 2 seconds is to be sent see Point 6 2 7 The automatic search tuning scan for ter
15. restrial TV transmitters will 2 Take the AVS 850 Power Transmitter run for the TV level it takes about 1 minute place it next to the AVS 840 Power 8 Select the level CATV with the TV CATV button Receiver and connect only the mains 9 Press the SCAN button and the TV will display PROGRAMME adapter PRESS SCAN AGAIN so press SCAN again within 2 seconds 3 Take the RC 815 remote control unit and 10 The automatic search tuning scan for the CATV level cable TV will press the buttons FUNC and SET run simultaneously for about 2 seconds The 11 Finished with the channel section button CH you can now page red LED will flicker when you let go of through all the channels that have been found them 12 To delete channels or to put them back press the CH button 4 Use the number keys 0 to 9 to enter a see description of RC 815 Point 5 three digit code number Any number is 13 The TV CATV button can be used to select either TV or cable TV available between 000 and 255 RC Blount Yad remote control unit Press the SET button Switch on the television set connected to the AVS 840 Power Receiver and select the AV input You will see the lettering RF ID XXX XXX represents the code currently set on the RC 815 remote control unit Disconnect the mains adapter of the AVS 850 from the wall socket for a moment and then insert it again Point the RC 815 remote control unit at the AVS 84
16. ringing into operation 7 1 Connecting the AVS 850 Power Transmitter Scart cable accessory Radio TV Co axial cable Co axial cable AV out VCR SAT Insert the cable branch plug A into the TV cable socket Insert the adapter B into the aerial socket of the AVS 850 Connect the cable branch plug A and the aerial input B of the AVS 850 with the enclosed co axial cable C using the adapter B Connect the cable branch plug A and the aerial input D of the TV set with the existing co axial cable E not included with this system Connect the video output F of the video recorder or SAT receiver with the video input G of the AVS 850 using the cinch scart cable labelled out Connect the video output H of the AVS 850 with the video input I of the television set cable not included with this system Note Points 5 and 6 are not necessary if the signal from the video recorder is not to be transmitted Note If you use a cinch cable for the connection accessory note when connecting the unit that the colour of the plug has to match the colour of the socket on the unit If they are different please note the following the yellow plug carries the video signal and must be inserted into the video socket the red one goes into audio right and the white one into audio left Insert the mains adapter plug in
17. to a 230 V mains socket and the unit plug into the socket provided Never use any other mains adapter than this one Switch the AVS 850 on with the POWER switch an LED lights up Place the AVS 850 video transmitter in a favourable position such as on top of the television set 9 Insert the RX 579 infra red module into the IR Extender socket provided and glue the infra red diode onto the eye of the unit it is to control see Point 3 29 7 Starting up 7 2 Connecting the AVS 850 Power Receiver The AVS 840 receives the AV signal from the AVS 850 Power Transmitter The output signal is available from the AV sockets on the rear side of the unit Antenne Connecting 1 30 Insert the cinch plug of the connecting cable into the AV socket of the Power Receiver Make sure the colour on the plug is the same as the one on the socket Now connect the plug at the other end of the cable to the unit that is to receive the signals Make sure that the enclosed scart plug is inserted the right way round Use the cable labelled In Do not exert force when inserting the plug NOTE If you use a cinch cable for the connection accessory note when connecting the unit that the colour of the plug has to match the colour of the socket on the unit If they are different please note the following the yellow plug carries the video signal and must be inserted into the video socket the red on
Download Pdf Manuals
Related Search