Bissell 80E7 Carpet Cleaner User Manual
Contents
1. 1 Power cord not firmly plugged in Vacuum cleaner won t pick up dirt Possible causes 1 Incorrect height adjustment 2 Hose not attached to suction opening 3 Twist n Snap hose not securely attached 4 Crack or hole in hose 5 Broken or worn drive belt 6 Rotating floor brush bristles worn 7 Rotating floor brush jammed 8 Clog in vacuum 9 Dirt container full 10 Dirt container not installed properly 11 Filters are dirty 12 Primary separator missing or installed incorrectly Tools won t pick up dirt Possible causes 1 Crack or hole in hose Vacuum hose wand or tools clogged Dirt container full Dirt container or upper tank not installed properly Filters are dirty 6 Primary separator missing or installed incorrectly Vacuum cleaner difficult to push Possible causes 1 Incorrect height adjustment 2 Rotating floor brush not rotating Visible dirt escaping from cleaner Possible causes 1 Dirt container full 2 Filters missing or installed incorrectly Bissell www bissell com A WARNING To reduce the risk of electric shock turn power OFF and dis connect plug from electrical outlet before performing maintenance or troubleshooting Remedies 1 Check electrical plug Remedies 1 Adjust powerfoot to correct height setting 2 Grasp Quick Release handle and firmly push hose wand onto the suction opening 3 Make sure Twist n Snap hose is snapped into locked position2. Check hose and replace if needed Replace drive belt see page 11 Replace brush Remove brush and clean debris from brush ends Follow instructions for clearing clogs on page 12 Empty dirt container 10 Position correctly and lock in place 11 Check and clean inner and outer circular filters and pre motor filter replace post motor filter 12 Check for a clog in the tube in the center of the dirt container clear and properly install primary separator Remedies Check hose and replace if needed Follow instructions for clearing clogs on page 12 Empty dirt container Position correctly and lock in place Check and clean inner and outer circular filters and pre motor filter replace post motor filter 6 Check for a clog in the tube in the center of the dirt container clear and properly install primary separator Remedies 1 Adjust powerfoot to correct height setting 2 Check drive belt and brush Remedies 1 Empty dirt container 2 Check inner and outer circular filter and post motor filter for correct installation 13 Troubleshooting Visible dirt escaping from cleaner continued Possible causes Remedies 3 Dirt container installed incorrectly 3 Position correctly and lock into place 4 Filter cup installed incorrectly 4 Remove dirt container and make sure filter cup is fully attached Other maintenance or service not included in the manual should be performed by an authorized service representative Thank you
3. EER Maintenance and care Clearing clog ES Low suction poor pickup or no suction may be due to a clog in the vacuum cleaner If you notice a change in the sound of the vacuum motor or a reduction in the spinning action in the dirt container check for clogs 1 Unplug cleaner from electrical outlet Primary Separator 2 Empty dirt container 3 Check upper tank and primary separa tor for build up or clogs Check to make sure primary separator is installed cor rectly To unlock the primary separator grasp the rim and turn toward the left Pull straight down to remove If the pri mary separator is missing or not locked into place check and clear the tube in the center of the dirt container and prop erly install primary separator 4 Remove the Twist n Snap hose from the vacuum by turning to the left Check the suction inlet hose and hose wand for clogs Remove any clogs from the hose using a long narrow object such as a broomstick 5 Check the foot hose for clogs If need ed remove the screw attaching the hose wand base to the vacuum Straighten the foot hose and unclog with alone narrow object such as a broomstick 6 If the clog persists follow the instructions for checking the rotating floor brush on poge 11 and inspect the air passageway or obstructions Air Passageway A 12 Bissell www bissell com A Troubleshooting Vacuum cleaner won t turn on Possible causes
4. be supervised to ensure that rey do not play with the appliance Mi Remove plug from electrical outlet before cleaning or maintaining the appliance E If the supply cord is damaged it must be replaced by the manufacturer or its service agent in order to avoid a hazard E Do not pick up toxic material chlorine bleach ammonia drain cleaner petrol etc E Do not allow to be used as a toy E Do not use for any purpose other than described in this User s Guide E Use only manufacturer s recommended attachments E Do not use with any opening blocked keep free of dust lint hair and anything that may reduce air flow E Keep appliance on a level surface E Turn off all controls before unplugging E Be extra careful when cleaning stairs E This appliance is provided with double insulation Use only identical replacement parts E Do not use without the dirt container and filters in place E Pay close attention when working around children E Unplug before attaching TurboBrush tool E Do not pick up hard or sharp objects such as glass nails screws coins etc SAVE THESE INSTRUCTIONS FOR FUTURE USE This model is for household use only IMPORTANT FOR OPERATION ON A 220 240 VOLT A C 50 60 Hz POWER SUPPLY ONLY If your appliance is fitted with a nonrewireable BS 1363 plug it must not be used unless a 13 amp ASTA approved to BS 1362 fuse is fitted in the carrier contained in the plug Spares may be ob
5. for selecting a BISSELL product Please do not return this product to the store Replacement parts Item Part No Part Name 1 32074 Style 7 9 10 12 14 Drive Belt 2 Pack 2 203 1056 Crevice Tool 3 203 1059 Combination Dusting Brush Upholstery Tool 4 203 1068 Extension Wand 5 203 1216 Twist n Snap Vacuum Hose Select Models Only 6 203 5624 Brush Roll 7 32064 Style 9 10 12 Inner amp Outer Circular Filter Set 8 32065 Style 9 10 12 Inner Circular Filter only 9 3205 Style 12 HEPA Media Filter 203 1215 Pre Motor Filter 203 1429 TurboBrush O 6 7 8 9 7 Ww cin S as S N E TE The Filter Media not the vacuum as a whole complies with the High Efficiency Particulate Air HEPA filter specification EN 1822 1 2009 1 Bissell www bissell com Warranty This warranty gives you specific legal rights and you may also have other rights which may vary from country to country If you hs additional instruction regarding this warranty or have questions regarding what it may cover please contact BISSELL Consumer Services by telephone or ails post as described below or contact your local in country distributor Limited One Year Warranty Subject to the EXCEPTIONS AND EXCLUSIONS identified below BISSELL Homecare Inc will replace with new or remanufactured components at BISSELL s option free of charge from the date of purchase by the original purchaser for one y
6. BISSEll Experts In Home Cleaning CLEANView amp CLEANVIieW POWER CYCLONIC pee cyclonic USER S GUIDE 80E7 and 28F4 SERIES 220 240V 2 Thank You 3 Safety Instructions 4 Product View Ei Al Biss E FICLEANVIEW CYCLONIE fais 5 Assembly 6 7 Operations 8 12 Maintenance and Care 13 14 Troubleshooting 14 Replacement Parts 15 Warranty 16 Consumer Services Thanks for buying a BISSELL Cleanview Cyclonic We re glad you purchased a BISSELL Cleanview cyclonic vacuum Everything we know about floor care went into the design and construction of this complete high tech home cleaning system Your BISSELL Cleanview cyclonic vacuum is well made and we back it with a limited one year warranty We also stand behind it with a knowl edgeable dedicated Consumer Services department so should you ever have a problem you ll receive fast considerate assistance My great grandfather invented the floor sweeper in 1876 Today BISSELL is a global leader in the design manufacture and service of high quality homecare products like your BISSELL Cleanview cyclonic vacuum Thanks again from all of us at BISSELL ord 4 Kb Mark J Bissell Chairman President amp CEO 2 Bissell www bissell com IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance basic precautions should be observed including the following READ ALL INSTRUCTIONS BEFORE USING YOUR UPRIGHT VACUUM A WARN
7. ING To reduce the risk of fire electric shock or injury E Do not use outdoors or on wet surfaces E Do not leave machine when it is plugged in E Do not use with damaged cord or plug E If appliance is not working as it should has een dropped damaged left outdoors or dropped into water return it to a service agent E Do not pull or carry by cord use cord as a handle close door on cord pull cord around sharp corners or edges run appliance over cord or expose Bes to heated surfaces E Do not unplug by pulling on cord Unplug by grasping plug E Do not handle plug or appliance with wet hands E Do not expose hair loose clothing fingers or body parts to openings or moving parts E Do not pick up hot or burning objects such as cigarettes matches or hot ashes E Do not a up flammable or combustible materials lighter fluid petrol kerosene etc or use in the presence of explosive liquids or vapour E Do not use appliance in an enclosed space filled with vapours given off by oil base paint paint thinner some moth seal A substances flammable dust or other explosive or toxic vapours E Not intended for use by persons including children with reduced physical sensory or mental capabilities or ak of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety Bissell www bissell com E Young children should
8. Stand the vacuum upi on and place the handle on the top of the vacuum body 3 Insert the screws into the existing holes on each side Tighten securely with a screwdriver Attach vacuum hose and tools 1 Attach the Twist n Snap hose by lining up the tabs on the base with the corresponding notches on the back of the vacuum 2 Turn the Twist n Snap hose to the right to lock the hose into place 3 Grasping the Quick Reach handle slide the end of the hose wand into the hose cme base Snap the hose into the hose clip NOTE The powerfoot will not operate effectively unless the hose wand is firmly attached 4 Slide the extension wand and the crevice tool together into the storage clip on the side of the vacuum E i Baa i a i Te aa 5 Snap the combination tool into the storage clip on the back of the vacuum 6 Select models only The TurboBrush tool bracket slides into the front of the handle Attach the bracket by aligning the pegs with the holes on the handle and pulling down until it locks into place 7 Select models only Place the TurboBrush fool in the bracket by aligning the bottom of the bracket with the opening of the brush roll and snap the TurboBrush tool into place Bissell www bissell com faa Operations Handle position Press the handle release pedal with your foot to place your BISSELL Cleanview cycloni
9. The post motor filter is a white pleated HEPA media fier A WARNING be replaced when it becomes dirty To reduce the risk of injury from moving parts turn the 5 Replace the door by inserting the tabs on sie switc ie an ical the left side and snapping the right side into m Pug Tom SIEGNIEg place nee Maintaining the TurboBrush tool Select models only The TurboBrush tool should be checked regularly for clogs or debris wrapping around the brush roll 1 Remove TurboBrush tool from hose or front of vacuum 2 Twist collar so opening is at the top and lift top cover to remove 3 Remove brush from belt and clean debris 4 Replace brush inside belt and place ends into slots on sides 5 Reposition top cover making sure to line up the inside tab at the front with the opening on the cover Twist collar until opening is at the bottom to lock into place The Filter Media not the vacuum as a whole complies with the High Efficiency Particulate Air HEPA filter specification EN 1822 1 2009 Bissell www bissell com Maintenance and care Check rotating floor brush and drive belt You should check your vacuum cleaner s rotating floor brush and drive belt regu larly for wear or damage You shoul also clean the brush and brush ends of string hair and carpet fibers These can wrap around the brush and hamper its ability to wali clean your carpet Also remove any debris that has accu mul
10. ated under the brush cover 1 Unplug cleaner from electrical outlet 2 Place handle in low position and turn vacuum cleaner over so bottom side is up 3 Remove the two screws from the brush slay shown with a Phillips head screwdriver Lift the brush cover off Motor 4 Grasp rotating floor brush at both ends Pulley and lift 5 Clean strings hair and other debris from rotating floor brush paying par ticular attention to brush ends 6 Clean strings hair and other debris from motor pulley and drive belt areas 7 Check drive belt carefully for wear cuts or stressed areas Replace if worn or damaged 8 Check air passageway for obstructions Remove debris from this area Replace drive belt 1 Unplug cleaner from electrical outlet 2 With rotating floor brush removed from vac uum cleaner Steps 1 4 of Check rotating floor brush and drive belt grasp old drive belt and remove from motor pulley Discard old drive belt 3 Place new drive belt over motor pulley and stretch other end over rotating floor brush in the space between the bristles 4 Place ends of rotating floor brush down into slots on sides as shown 5 Turn rotating floor brush by hand several times in direction of motor pulley If prop erly installed drive belt will center itself on rotating brush 6 Reposition brush cover and replace two screws Make sure end of brush cover is snapped into place a Bissell www bissell com
11. c bagless vacuum into one of three cleaning positions 1 Upright For storage and above floor cleaning with special tools 2 Normal Cleaning Press handle release pedal once Use for most household floor cleaning tasks 3 Low Cleaning With the vacuum in normal cleaning position handle release pedal again Use tor reaching under low furniture such as tables chairs AN CAUTION and beds Before using your vacuum make sure P that the dirt container is in locked Powerfoot height adjustment position and that all filters inner circular ee a te a _ t d The powerfoot rotating floor brush on Sai aiaa a ee peace soe your BISSELL Cleanview cyclonic bagless your vacuum without these filters vacuum can be adjusted to clean several floor surfaces NOTE For optimal cleaning ATTE NTION performance adjust to the lowest Some Berber carpets have a tendency to practical setting If your cleaner is fuzz with wear Repeated strokes in the difficult to Puen adjust 19 the next same area may aggravate this condition higher setting Consider setting your cleaner on a higher than normal setting for this type of carpet lip 1 Place handle in upright position 2 Turn height adjustment knob to desired setting Lowest Setting For bare floors Medium Settings For short and medium pile carpets e e e under low furni Highest Setting For plush pile carpets e 3 Place the
12. d detergent may be used if desired Rinse well then air dry thoroughly before putting them back together and replacing in filter cup 5 The filter cup may be washed in warm water with a mild detergent Make sure it l completely dry before reassembling with ilters 6 The upper tank and primary separator may be wiped clean with a damp cloth Reach underneath the upper tank and turn the rim of the primary separator to unlock Pull straight down to remove Cleaning the pre motor filter 1 Unplug the cleaner from electrical outlet WARNING 2 The pre motor filter protects the motor from debris It is located underneath the Do not operate cleaner wit dirt container and filter cup in the center damp or wet filters or without of the round part of the Lock n Seal a els pe lever 3 Remove the small round premotor filter and any debris on top of it Rinse well under warm water then air dry thoroughly before replacing Pre Motor Filter Bissell www bissell com Maintenance and care Replacing the HEPA media post motor filter The post motor filter is a H13 HEPA media filter which assists in the filtration process to return clean air to the room 1 Unplug the vacuum from electrical outlet HEPA Media ae i yi 2 Remove the filter door located on the Post Motor Ait front of the vacuum Filter 3 Remove the post motor filter 4 Replace the post motor filter with a new filter NOTE
13. ear any defective or malfunctioning part do to manufacturers defect This warranty applies to product used for personal and not commercial or rental service This warranty does not apply to fans or routine maintenance components such as filters belts or brushes Damage or malfunction caused by negligence abuse or use not in accordance with the User s Guide is not covered For UK inquiries For spare parts and accessories Monday Thursday 9 am 5 pm Monday Friday 9am 5 30 pm Friday 9am 4 pm Exserve Ltd BISSELL Homecare Overseas Inc 550 Peterborough Cound oor Cambridgeshire PE2 6WH 996 Berwick Avenue Telephone 01733 362415 Slough Berkshire SL 4QT United Kingdom Telephone 0844 888 6644 BISSELL HOMECARE INC IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY NATURE ASSOCIATED WITH THE USE OF THIS PRODUCT BISSELL S LIABILITY WILL NOT EXCEED THE PURCHASE PRICE OF THE PRODUCT EXCEPTIONS AND EXCLUSIONS FROM THE TERMS OF THE LIMITED WARRANTY THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY OTHER WARRANTIES EITHER ORAL OR WRITTEN ANY IMPLIED WARRANTIES WHICH MAY ARISE BY OPERATION OF LAW INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED TO THE ONE YEAR DURATION FROM THE DATE OF PURCHASE AS DESCRIBED ABOVE 15 Bissell www bissell com BISSELL consumer services If your BISSELL product should require service Call BISSELL Consumer Servic
14. es at the numbers below and we will give you the location of a BISSELL Authorized Service Center in your area For all other countries contact your local in country distributor for questions service or repair If you have questions about your warranty or need replacement parts please contact the numbers below For UK inquiries For spare parts and accessories Monday Thursday 9 am 5 pm Monday Friday 9am 5 30 pm Friday 9 am 4 pm Exserve Ltd BISSELL Homecare Overseas Inc 550 Peterborough Ground Foor Cambridgeshire PE2 6WH 326 Berwick Avenue Telephone 01733 362415 Slough Berkshire SL 4QT United Kingdom Telephone 0844 888 6644 Or visit the BISSELL website www bissell com When contacting BISSELL have model number of cleaner available Please record your Model Number Please record your Purchase Date NOTE Please keep your original sales receipt It provides proof of purchase date in the event of a warranty claim See Warranty on page 15 for details Bissell Experts In Home Cleaning 2011 BISSELL Homecare Inc Grand Rapids Michigan All rights reserved Printed in China Part Number 110 4353 Rev 3 11 Visit our website at www bissell com 16 Bissell www bissell com
15. handle into the normal cleaning first for objects position and the powerfoot will adjust to that might harm the setting chosen the unit or block the vacuum hose lip Your vacuum features a Quick Release cord wrap To remove the power cord Ho and eas ily rotate the upper cord wrap towards the floor Carrying and slip power Handle cord from upper and lower cord wraps NOTE You may also adjust the setting while in the normal cleaning position Transporting cleaner 1 To move your cleaner from room to room put the handle in the upright position tilt the cleaner back on its rear wheels and pus forward 2 The cleaner can also be moved by using the carrying handle on the back www bissell com pas Operations NOTICE Special tools Your BISSELL Cleanview cyclonic bagless vacuum is not only a powerful carpet and rug vacuum cleaner it s also a ver satile above floor vacuum cleaner when you select one of the special tools 1 Raise handle to upright position 2 Grasp the Quick Reach handle and lift hose wand to separate from suction intake opening The floor brush will continue to rotate while you use your vacuum for above floor cleaning To prevent carpet damage do not lean on the vacuum or let the power foot tilt forward lip Hair string and small objects can Heal the vacuum hose or tools Check them occasionally for obstructions 3 Attach tools by fir
16. ide of the container 1 Unplug cleaner from electrical outlet Unlock Position Lock Position Y 2 Slide the Lock n Seal lever to the Unlock position 3 Grasp handle and pull dirt container straight out to remove from vacuum 4 Empty dirt into garbage container 5 Put dirt container back in the vacuum and slide the lever to the Lock position Note The dirt container may be washed in warm water with a mild detergent Remove the filter cup from the bottom before washing Make sure it is completely dry before reassembling with the filter cup The Filter Media not the vacuum as a whole complies with the High Efficiency Particulate Air HEPA filter specification EN 1822 1 2009 Bissell www bissell com Maintenance and care Cleaning the inner amp outer circular filters 1 Unplug cleaner from electrical outlet 2 Remove the dirt container as described N OT i z z in the previous section Grasp the filter This product is intended for household use cup located at the bottom of the dirt only and not for commercial or industria container and twist counterclockwise to use Vacuuming of dust from products like unlock and remove plaster concrete or ashes will damage the motor and void the warranty 3 Grasp the circular filters and pull straight up to remove 4 Separate the outer foam and inner pleated circular filters Wash each indi vidually by hand in warm water Mil
17. mly pushing onto vacuum hose or extension wand ranon Dusting Brush Upholstery Tool Two types of cleaning tools are included in one attachment rotate for desired tool W Use brush side to dust furniture blinds books lamps shelves and baseboards WE Use upholstery side for curtains draper ies cushions and fabrics s Crevice Tool Use in tight narrow spaces Extension Wand Use with desired attach ment for a longer reach TurboBrush tool Select models only AN O Use rotating brush action for small areas such CAUTI N The rotating floor brush continues to rotate while tools are in use To reduce the risk of injury from mov ing parts always move the cleaner as stairs and upholstery NOTE Press gently when using the TurboBrush tool to gain maximum cleaning Too much pressure will ahh na hardl i with the carrying handle at the cause the brush to stop rotating back of the cleaner Always place d the vacuum cleaner on the floor Power cor with the handle in upright inom when mas fools Never place your fingers under the cleaner when it is When you are done using your BISSELL Cleanview pape Bagless vacuum return it to the upright position and running Never place powerloot on h dl furniture or uneven surfaces Do not store the power cord place vacuum cleaner close enough 1 Turn power switch OFF oi fo pull them into rotating rush 2 Unplug power cord by grasping the plu NOT the c
18. ord and disconnect from outlet 7 NOTICE Loop power cord around cord wraps on i hil mi i sde ol vanuum oledner 7 le vacuuming certain carpets and low umidity conditions may Seka small 4 Clip molded plug to power cord to secure static joan a The discharges are entirely harmless and are not associated in any way with the main power supply Bissell www bissell com Maintenance and care To maintain maximum cleaning performance from your BISSELL Cleanview cyclonic bagless vacuum AN WA R N f N G alii these simple maintenance To reduce the risk of electric shock turn 1 Empty the dirt container when the dirt silts switch OFF and disconnect plug om electrical outlet before performing reaches the Full line on the side maintenance or troubleshooting checks 2 Check the inner and outer circular filters and the pre motor filter at least once a month and clean or replace as Ti needed Pp For maximum cleanin 3 Replace the HEPA media postmotor performance check 9 tilter every three to six months and clean or replace Note More frequent filter cleaning all filters as suggested or replacing may be necessary if you are vacuuming new carpef ine dust or have allergy concerns Follow the instructions on the fol lowing pages to perform these simple maintenance steps Emptying dirt container ee The dirt container needs to be emptied when the dirt reaches the Full line on the s
19. tained from your BISSELL supplier If for any reason the plug is cut off it must be disposed of as it is an electric shock hazard should it be inserted into a mains socket 3 Product view Cord Clip Hose Clip Deluxe Stretch Hose Handle TurboBrush Tool select models only Crevice Tool Carrying Handle xtension Twist n Wand uel ee Ralease ad il Quick Cord Wrap Reach Combination Handle ee Primary Dustin Lissa Wand WA Separator Brush E Upholstery Oo ranpe te Upper Tank Tool ES Hose Wand Base Power Cord Power Switch a ane Dirt Circular T a j Filters Pedal Filter Cup Pre Motor Lock n Filter Seal Lever Foot Hose Height HEPA Media PostMotor Filter CAUTION Do not plug in your vacuum cleaner until you are familiar with all instructions and operating procedures Furniture Protection Guard The Filter Media not the vacuum as a whole complies with the High Efficiency Particulate Air HEPA filter specification EN 1822 1 2009 Powerfoot Bissell www bissell com Assem bly The only tool you ll need to assemble your vacuum cleaner is a screwdriver AN WARN i NG Attach handle to vacuum Plastic film can be dangerous To avoid danger of suffocation keep 1 Locate the vacuum handle and remove away fron babiesand children the screw packet taped to the base of the handle 2
Download Pdf Manuals
Related Search