Bissell 1690C Vacuum Cleaner User Manual
Contents
1. dry Vacuum thoroughly to pick up loose debris and pet hair Use a vacuum with a brush attachment and a crevice tool to clean in fabric folds and tufts Machine Preparation Set up the machine following instructions in The Basics sec tion on pages 6 9 Using the Measuring Cup provided pour BISSELL Advanced Deep Cleaning Formula into the Tank in Tank 4 18 05 9 20 04 AM E Maintenance Storage Power Cord Power switch OFF Quick Release e Unplug power cord from the outlet and coil around Power Cord Quick Release Remove rinse tools in clean running water let Flex Hose dry and replace in tool caddy Storage Pracket Coil flex hose through storage brackets o Remove Tank in Tank dispose of dirty water See The Basics section on page 6 Rinse out the Tank in Tank and reseat the tank unto the machine all exterior surfaces with a soft cloth 8 Store cleaner upright in a protected dry area When carpet is dry vacuum again to remove hair fuzz that A CAUTI 0 N the POWERSTEAMER may have loosened PowerSteamer uses water and Pump Belt and Brush Belt Replacement must not be stored where there is a Tun the machine off and unplug from wall outlet danger of freezing Freezing will Step on the release pedal and recline the handle down onto damage internal floor components and Remove the Tank in Tank Set them aside void the warranty Remo2. 6 Replacement Parts Not all parts included with every model Item PartNo Part Name 1 214 4025 Handle Assembly with Screw 215 9155 Tough Stain Brush 3 015 9043 Tank Assembly Complete 4 015 4439 Tank Lid Assembly 5 015 9041 Tank Bottom 6 213 0213 Baffle with Red Float 7 210 4052 Window Gasket 8 215 0628 Replacement Pump Belt with instructions 9 015 0621 Replacement Brush Belt with instructions 10 015 3500 Lint Screen 11 213 3010 Measuring Cup 12 214 9131 Bare Floor Tool 13 0710 48 oz BISSELL Fiber Cleansing Formula with Scotchgard Protector 14 0400 22 oz BISSELL Tough Stain PreCleaner 15 0484 32 oz BISSELL Hard Floor Solutions M ug310 5907 1692 1694 205 indd 15 4 18 05 9 20 07 7 About Your Warranty This warranty gives you specific legal rights and you may also have other rights which may vary from state to state If you need additional instruction regarding this warranty or have questions regarding what it may cover please contact BISSELL Consumer Services by E mail telephone or regular mail as described below Limited One Year Warranty Subject to the EXCEPTIONS AND EXCLUSIONS identified below upon receipt of the product BISSELL Homecare Inc will repair or replace with new or remanufactured components or products at BISSELL s option free of charge from the date of purchase by the original purchaser for one year any defective or malfunctioning part See information be
3. Bissell PowerSteamer 1692 1693 1694 PowerSteamer Series 8805 8806 PowerSteamer Series sicoar 3 POWERSteamer 4 5 Assembly Instructions 5 11 Beenie TOOLS S 11 REGE Troubleshooting Consumer Services p leaning lt 4 5 bra N power 16 ug310 5907 1692 1694 205 indd 1 4 18 05 9 19 48 AM gt Thanks For Buying A BISSELL PowerSteamer Deep Cleaner We re glad you purchased a BISSELL PowerSteamer Deep Cleaner Everything we know about floor care went into the design and construction of this complete high tech home cleaning system Your PowerSteamer is well made and we back it with a limited one year warranty We also stand behind it with a knowledgeable dedicated Consumer Services department so should you ever have a problem you ll receive fast considerate assistance My great grandfather invented the floor sweeper in 1876 Today BISSELL is a global leader in the design manufacture and service of high quality homecare products like your PowerSteamer vna e 7 Y Mark J Bissell President and Chief Executive Officer ug310 5907 1692 1694 205 indd 2 4 18 05 9 19 51 IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance basic precautions should be observed including the following Read all instructions before using your POWERSTEAMER A WARNING To r
4. EITHER ORAL OR WRITTEN ANY IMPLIED WARRANTIES WHICH MAY ARISE BY OPERATION OF LAW INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND BISSE FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED TO THE ONE YEAR DURATION FROM THE DATE OF PURCHASE AS DESCRIBED ABOVE Some states do not allow limitations on how long an implied warranty lasts 92005 BISSELL Homecare Inc Grand Rapids Michigan so the above limitation may not apply to you AI rights reserved 2 Part Number 310 5907 NOTE Please keep your original sales receipt It provides proof of Rew3 05 date of purchase in the event of a warranty claim Visit our website at www bissell com Scotchgard is a trademark of 3M ug310 5907_1692 1694_205 indd 16 4 18 05 9 20 10 AM
5. Re install the brush into the base of the unit Place the black brush arm onto the Brush and slide black brush arm into original position Qo Re install the Red Retainer Plate and Phillips head screw Using your finger gently spin the replacement pump belt on the silver motor shaft If assembled correctly the replacement Pump Belt should rotate freely around the silver motor shaft and drive pulley without obstruction The brush should also rotate freely when the silver motor shaft is turned Turn the machine right side up and replace the Tank in Tank and belt access door Assembly is now complete If you have any questions or are having trouble installing your replacement pump belt please call BISSELL Consumer Services at 1 800 237 7691 4 18 05 9 20 05 AM Troubleshooting Reduced Spray Or No Spray Possible Causes Bladder may be empty The Lint Screen may be clogged Tank in Tank may not be seated properly Pump may have lost prime Q The Pump Belt may be broken DirtLifter PowerBrush Does Not Turn Possible Causes AN WARNING To reduce the risk of fire electric shock or injury unplug appliance from outlet before servicing Remedies Turn power OFF refill tank with hot tap water Q Clean out Lint screen page 7 Q Turn power OFF remove tank and reseat tank Turn power OFF after 1 minute turn ON and depress Spray trigger Q po
6. Trigger Floor Nozzle Window Power Switch Measuring Flex Hose Cup Tank in Tank Easy Rollin Wheels Release ug310 5907 1692 1694 205 indd 4 DirtLifter PowerBrush select models only 4 18 05 9 19 52 AM Secure the handle by placing 1 Phillips head 69 screw ug310 5907 1692 1694 205 indd 5 How To Use This Guide This User s Guide is designed to help you get maximum satisfaction from your PowerSteamer Deep Cleaner Enclosed you ll find assembly instructions for cleaning tasks safety precautions cleaning tips maintenance and troubleshooting information Please read this guide thoroughly before assembling and using your cleaner Pay particular attention to the assembly diagram assembly instructions and part names Locate and organize all parts before assembly Familiarize yourself with all parts and features and how they operate Following the Guide will enhance your ability to get top performance from your cleaner for many years If you have any questions or comments please call BISSELL Consumer Services at 1 800 237 7691 How To Assemble i Your PowerSteamer assembles in two quick steps The only tool you will need to assemble your cleaner is a Phillips head 52 screwdriver Your PowerSteamer is packaged as two primary components the Lower Body and the Handle Assembly To assemble e Slide the Handle Assembly with attached Quic
7. ctive cleaning for linoleum vinyl and tile floors Caution Do not use on hardwood floors o Use only BISSELL Hard Floor Solutions 2cuum or sweep thoroughly to pick up loose debris and pet hair 5 Remove easily moved furniture from the room chairs tables etc Handle Release Plan your cleaning route to leave exit path Plan activities to allow about 30 minutes for the floor to dry completely Attach The Bare Floor Tool o Step on the handle release to lay the machine handle down Remove the Tank in Tank from the machine base Lift the machine base to expose the underside of the nozzle Attach Bare Floor Tool to nozzle with long tab to the right side ReadyTools side of the nozzle Bare Floor First attach left side short tab catching tab over nozzle edge Cleaning Tool Q Gently bend long tab right side outward to easily snap over me edge of clear nozzle on right jap ep aN ug310 5907 1692 1694 205 indd 9 4 18 05 9 19 57 AM Set the ReadyTools dial to Tools or PreTreat ug310 5907 1692 1694 205 indd 10 Machine Preparation Set up machine following the instructions in The Basics on pages 6 9 Be sure to thoroughly rinse out any remaining Fiber Cleansing Formula from the Tank in Tank bottle to prevent slippery linoleum vinyl and tile floors Use BISSELL Hard Floor Solutions in the Tank in Tank o Check ReadyTools dial it should be set
8. e Floor Nozzle Window are inserted through the mating slots in the main housing Reinstall if necessary Tank in Tank Lid is not properly installed Reinstall lid refer to The Basics section page 6 Tank in Tank is not properly seated Tank in Tank must be firmly seated to function Remove and reseat Tank in Tank Q Poor tool position Q Readjust angle apply more Handheld attachments only downward pressure Q Tank in Tank has picked up the maximum Q Empty tank and refill refer to dirty water The Basics section page 6 Thank you for selecting a BISSELL product If you should happen to need assistance during assembly or operations call 1 800 237 7691 Please do not return this product to the store BISSELL Consumer Services For information about repairs or replacement parts or questions about your warranty call BISSELL Consumer Services 1 800 237 7691 Monday Friday 8 a m 10 p m ET Saturday 9 a m 8 p m ET Or write BISSELL HOMECARE INC PO Box 3606 Grand Rapids MI 49501 ATTN Consumer Services Or visit the BISSELL website www bissell com When contacting BISSELL have model number of unit available Please record your Model Number Please record your Purchase Date NOTE Please keep your original sales receipt It provides proof of date of purchase in the 14 event of a warranty claim See About Your Warranty on page 16 for details 4 18 05 9 20 0
9. educe the risk of fire electric shock or injury W Do not immerse i Use only on surfaces moistened by cleaning process Always connect to a properly grounded outlet See Grounding Instructions I Unplug from outlet when not in use and before conducting maintenance or troubleshooting Do not leave machine when it is plugged in Do not service machine when it is plugged in Do not use with damaged cord or plug E If appliance is not working as it should has been dropped damaged left outdoors or dropped into water have it repaired at an authorized Service Center Use indoors only Do not pull or carry by cord use cord as a handle close door on cord pull cord around sharp corners or edges run appliance over cord or expose cord to heated surfaces Wi Do not carry the appliance while in use Do not unplug by pulling on cord unplug by grasping plug not the cord Do not handle plug or appliance with wet hands I Do not put any object into appliance openings use with blocked opening or restrict air flow Wi Do not expose hair loose clothing fingers or body parts to openings or moving parts Do not pick up hot or burning objects E Do not pick up flammable or combustible materials lighter fluid gasoline kerosene etc or use in the presence of explosive liquids or vapor Do not use appliance in an enclosed space filled with vapors given off by oil base paint paint thinner some moth proofing substance
10. in Tank Before using the machine simply To reduce the risk of fill the Measuring Cup to the fill line with BISSELL fire electric shock Advanced Deep Cleaning Formula Pour the formula or injury unplug into the Tank in Tank as shown on page 7 For from outlet before convenience the Measuring Cup stores on the back servicing of the unit i To Fill The Tank in Tank This easy to use system is designed with a bladder inside to hold clean water As you clean the bladder will empty Dirty water collects in the tank outside the bladder NOTE Make sure to add formula to the tank before filling it with water e Depress the Handle Release pedal to tilt back the handle Rotate Handle Lift the Tank in Tank handle The handle locks the lid in to Unlatch place Carry the Tank in Tank like a bucket to fill at the sink Set the Tank down and rotate the handle forward to e gt 57 unlatch the Lid Lift off and set the Lid aside P ug310 5907 1692 1694 205 indd 6 4 18 05 9 19 55 ug310 5907 1692 1694 205 indd 7 To Fill The Tank in Tank Continued Using the Measuring Cup pour BISSELL Deep Cleaning Formula into the mouth of the bladder Qo Fill to the bottom of the neck with hot tap water Do not boil or microwave water NOTE Fill slowly to reduce sudsing Replace the Tank Lid matching the Lid and Tank edges Rotate the handle to carrying position Replace Tank in machine base seating f
11. irmly in place Rotate handle back down to latched position NOTE Remove the Tank in Tank following steps 1 through 3 on page 6 Pour out dirty water After each use remove and rinse the Lint Screen located on the Tank Lid Remove Tank Lid follow step 3 on page 6 Remove Lint Screen Rinse under faucet to remove any debris nsert Lint Screen back in Tank Lid The screen will click into place Replace Tank Lid Refill with cleaning solution and clean tap water follow steps 4 5 above NOTE When a cleaning job is complete rinse out the Tank in Tank by running clean water between the bladder and the tank Return the Tank in Tank to the machine follow step 6 above 15 Refer to the Maintenance Storage section on the next page for final cleanup M A special red float device in the tank will cause the cleaner to stop remov ing solution from the carpet The motor sound will rise in pitch to let you know the dirty water tank is full 4 18 05 9 19 56 ReadyTools Dial This provides floor or upholstery cleaning with the turn of a dial For carpet floor cleaning make sure the dial is set to FLOOR CLEANING For upholstery or fabric cleaning select your cleaning tool attach it to the Flex Hose switch to Tools Settings and the PowerSteamer is ready to clean upholstery fabrics and more Set the switch to FLOOR CLEANING when cleaning carpets or set it to TOOLS PRETREAT when usi
12. k Release Cord Wrap down into the Lower Body until it will go no further supplied through the screw opening in the Lower Body and into the rear of the Handle Assembly Tighten with screwdriver until secure Phillips Head Screw Assembly is now complete What Comes With Your PowerSteamer CN Tough Stain Brush 1607 Fiber Cleansing Tough Stain Formula with PreCleaner Scotchgard protector Keep plenty of BISSELL Advanced Deep Cleaning Formulas on hand so you can clean whenever it fits your schedule Always use BISSELL deep cleaning formulas Non BISSELL cleaning solutions may harm your cleaner and void the warranty 4 18 05 9 19 52 AM The Power Switch controls power to the machine Power Switch DirtLifter PowerBrush on select models The powered brush roll at the Floor Nozzle is designed to enhance cleaning performance The bristle pattern lifts out the deep down dirt while gently grooming carpet fibers The floating suspension self adjusts to Deep cleaning carpeting all carpet heights and protects your carpet if you leave and upholstery regularly the Power Switch ON When the machine handle is in can reduce dust and the fully upright position CarpetSaver automatically allergens in your home raises the brush off the carpet y Measuring Cup Your PowerSteamer is equipped with a Measuring Cup A for adding the proper amount of cleaning formula to WARN ING the Tank
13. low on If your BISSELL product should require service This warranty applies to product used for personal and not commercial or rental service This warranty does not apply to fans or routine maintenance components such as filters belts or brushes Damage or malfunction caused by negligence abuse neglect unauthorized repair or any other use not in accordance with the User s Guide is not covered If your BISSELL product should require service Contact BISSELL Consumer Services to locate a BISSELL Authorized Service Center in your area If you need information about repairs or replacement parts or if you have questions about your warranty contact BISSELL Consumer Services Website or E mail www bissell com Use the Customer Services tab Or Call BISSELL Consumer Services 1 800 237 7691 Monday Friday 8 am 10 pm ET Saturday 9 am 8 pm ET Or write BISSELL Homecare Inc PO Box 3606 Grand Rapids MI 49501 ATTN Consumer Services BISSELL HOMECARE INC IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY NATURE ASSOCIATED WITH THE USE OF THIS PRODUCT BISSELL S LIABILITY WILL NOT EXCEED THE PURCHASE PRICE OF THE PRODUCT Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you EXCEPTIONS AND EXCLUSIONS FROM THE TERMS OF THE LIMITED WARRANTY THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY OTHER WARRANTIES
14. ng the Flex Hose attachments How To Clean Carpet ug310 5907 1692 1694 205 indd 8 Q Plan activities to give carpet time to dry Remove easily moved furniture from the room chairs lamps coffee tables etc o Vacuum thoroughly to pick up loose debris and pet hair before using the PowerSteamer Plan your cleaning route to leave an exit path It is best to begin cleaning in the corner farthest from your exit NOTE You may notice hair and debris deposits on carpet that were loosened by brushing action especially with newer carpets that have never been deep cleaned before This debris should be picked up by hand and thrown away Debris that deposits in the brush belt area should be cleaned out to keep Belts running free Pretreating Improves cleaning effectiveness for heavily soiled carpet in high traffic areas such as entryways and hallways Set the ReadyTools dial to TOOLS PRETREAT Plug the PowerSteamer into a proper outlet and turn ON the Power switch While pressing the trigger slowly make several passes over the area to be cleaned Caution Do not overwet Turn the machine Power switch OFF and let BISSELL Advanced Deep Cleaning Formula dissolve the tough soil for 1 2 minutes Reset the ReadyTools Dial to FLOOR CLEANING before continuing Normal Cleaning Plug the PowerSteamer into a proper outlet and turn ON the Power switch e While pressing the Spray Release Trigger make one
15. on Floor Cleaning e Plug into a proper outlet and turn Power Switch ON Bare Floor Cleaning Technique Slowly move the machine nozzle with Bare Floor Tool forward and back over soiled surface one time while pressing the trigger Caution Do not over wet LN WARNING To reduce the risk o Repeat the motion without pressing the trigger using the Bare Floor Tool to squeegee and suction up the dirty water of fire electric shock or injury e Repeat steps 1 and 2 backing along the exit path unplug from outlet Allow about 30 minutes for the floor to dry completely before servicing Q When the cleaning job is complete refer to the Maintenance Storage section on page 11 Q To remove Bare Floor Tool gently bend long tab right side outward and pull tool down away from nozzle Rinse thoroughly dry and store How To Clean Upholstery and Small Areas Important Check Upholstery Tags Check manufacturer s tag before cleaning W or WS on the tag means you can use your PowerSteamer If the tag is coded with X or 5 with a diagonal strike through or says Dry Clean Only do not proceed Do not use on velvet or silk If manufacturer s tag is missing or not coded check with your furniture dealer Check for colorfastness in an inconspicuous place If possible check upholstery stuffing Colored stuffing may bleed through fabric when wet lanufacturers Tag Plan activities to give upholstery time to
16. pliance has an equipment grounding conductor and a grounding plug It must only be plugged into an outlet that is properly installed and grounded in accordance with all local codes and ordinances Grounded Outlets VAN WARN NG Improper connection of the equipment grounding conductor can result in a risk of electrical shock Check with a qualified electrician or service person if you aren t sure if the outlet is properly grounded DO NOT MODIFY THE PLUG If it will not fit the outlet have a proper outlet installed by a qualified electrician This appliance is designed for use on a nominal 120 volt circuit and has a grounding attachment plug that looks like the plug in the drawing above Make certain that the appliance is connected to an outlet having the same configuration as the plug No plug adapter should be used with this appliance 4 18 05 9 19 51 AM Product View A WARNING To reduce the risk of fire use only BISSELL Advanced Deep Cleaning Formulas in your PowerSteamer Use of cleaning formulas that contain lemon or pine oil may damage this Quick Release Cord Wrap appliance and void warranty Chemical spot cleaners or solvent based soil removers should not be used These products may react with the Power Cord Strain Reliever Handle Handle Assembly Lower Body plastic materials used in your Lower Cord PowerSteamer causing cracking Wrap or pitting Spray
17. s flammable dust or other explosive or toxic vapors Wi Do not pick up toxic material chlorine bleach ammonia drain cleaner gasoline etc Do not modify the 3 prong grounded plug Do not allow to be used as a toy Do not use for any purpose other than described in this User s Guide Do not operate the appliance unless the belt door is securely assembled in the location provided Use only manufacturer s recommended attachments Use only cleaning products formulated by BISSELL for use in this appliance to prevent internal component damage See the Cleaning fluid Section of this manual E Keep openings free of dust lint hair etc E Keep appliance on a level surface Turn off all controls before unplugging ug310 5907 1692 1694 205 indd 3 Wi Be extra careful when cleaning stairs Wi Close attention is necessary when used by or near children WARNING The Power Cord on this product contains lead a chemical known to the State of California to cause birth defects or other reproductive harm WASH HANDS AFTER HANDLING SAVE THESE INSTRUCTIONS THIS MODEL IS FOR HOUSEHOLD USE ONLY Commercial use of this unit voids the manufacturer s warranty GROUNDING INSTRUCTIONS This appliance must be connected to a grounded wiring system If it should malfunction or break down grounding provides a safe path of least resistance for electrical current reducing the risk of electrical shock The cord for this ap
18. slow Ti 2 forward and back wet pass Let the BISSELL Advanced Deep ID Cleaning Formula DirtLifter PowerBrush do the work for you Caution Do not overwet Thorough Release the trigger and make one slow forward and back pass vacuuming before over the same area to remove any residual dirty water deep cleaning will prevent early clogging of the lint trap o Repeat cleaning passes without pressing the trigger until you can t see any more water being suctioned up When cleaning job is complete refer to the Maintenance Storage section on page 11 4 18 05 9 19 56 Cleaning Fluid Section Keep plenty of genuine BISSELL Fiber Cleansing Formula on hand so you can clean and protect whenever it fits your schedule Always use genuine BISSELL deep cleaning formulas AN WARNING To Reduce the Risk of Fire and Electric Shock due to internal componet damage use only BISSELL cleaning fluids intended for use with the deep cleaner ffe sing 48 oz BISSELL 48 oz BISSHL 48 oz BISSELL 48 oz BISSELL Fiber Cleansing Multi Allergen Pet Odor and Natural Orange Formula with Removal Soil Removal Extract Formula scotchgard Formulawith Formulawith with Scotchgard Protector scotchgard scotchgard Protector item 0710 Protector Protector item 0740 item 0720 item 0730 Cleaning Bare Floors The Bare Floor Tool available with select models only provides effe
19. ve Belt Access Door located near the ReadyTools Dial Insert a flat head screwdriver into the slot nearest to the handle and gently prying the access door off o Turn the machine onto its side so the belt access area is facing upward On the bottom of the machine near the belt access area is a Red Retainer Plate that holds the black brush arm and brush in place Using a Phillips head screwdriver remove the screw that holds the Red Retainer Plate in place Set Red Retainer Plate and Phillips head screw aside NOTE For 1693 Model series remove stationary brush skip step 6 and 7 Remove the black brush arm that holds the brush in place Set the black brush arm aside o o Remove the toothed Brush Belt from the Brush then from the Red Pump Pulley Set the toothed Brush Belt and Brush aside Locate and remove the broken Pump Belt LN WARNING To reduce the risk of fire electric shock or injury unplug from outlet before servicing ug310 5907 1692 1694 205 indd 11 4 18 05 9 20 04 9310 5907 1692 1694 205 indd 12 Install The Replacement Pump Belt Q vin the unit still on its side loop one end of the replacement Pump Belt around the Red Pump Pulley and then the other end around the silver motor shaft Do not twist the replacement pump belt Re install the toothed Brush Belt first onto the Red Pump Pulley and then onto the toothed end of the Brush
20. wer OFF and unplug from the outlet To check if a Pump Belt has broken you will need a flat head Sy screwdriver Insert the blade end into the lower slot of the Belt Access door to release the lower snap If necessary insert the blade end into the upper slot to release the upper snap Examine the belt for breakage You should be able to see the Pump Belt looped around the motor shaft If it is broken or missing please refer to the part numbers and descriptions on page 15 before calling Consumer Services Complete installation instructions will accompany the replacement belt Remedies The Brush Belt or Pump Belt may be broken power OFF and unplug ug310 5907 1692 1694 205 indd 13 from the outlet To check if a Brush Belt has broken you will need a flat head S screwdriver Insert the blade end into the lower slot of the Belt Access door to release the lower snap If necessary insert the blade end into the upper slot to release the upper snap Examine the belt for breakage If broken refer to pages 11 12 4 18 05 9 20 06 ug310 5907 1692 1694 205 indd 14 Troubleshooting Continued PowerSteamer is not picking up solution and water Possible Causes Remedies ReadyTools Dial may be at the Set ReadyTools Dial to either FLOOR wrong setting for cleaning job CLEANING or TOOLS PRETREAT Nozzle Window may not be properly attached Make sure the two tabs on the back of th
Download Pdf Manuals
Related Search