Home
Beko LG-BKE 7800 D Air Conditioner User Manual
Contents
1. OWNER S MANUAL AND INSTALLATION GUIDE MS1500 XD MARINE HIGH POWER AM FM STEREO RADIO WITH www asaelectranics com COMPACT DISC PLAYER CDC SHUTTLE CONTROLS Visit us at www asaelectronics com to see our full line of mobile audio and video products AND WIRED REMOTE CAPABILITY MADE IN CHINA INSTALLATION Preparation Please read entire manual before installation Before You Start 1 Disconnect negative battery terminal consult a qualified technician for instructions 2 Avoid installing the unit where it would be subject to high temperatures such as from direct sunlight or where it would be subject to dust dirt or excessive vibration Getting Started 1 Remove 2 transit screws located on top of the unit 2 Insert the supplied keys into the slots as shown and slide the unit out of the mounting sleeve 3 Install mounting sleeve into dash opening bending tabs to secure 4 Some vehicles may require an installation kit and or wiring harness adapter sold separately 5 Ensure that the 51500 is installed horizontally 6 Attach speaker and power wires to the mating harness pigtails supplied with the MS1500 7 Carefully double check the wiring then plug the pigtails into the radio harness and the harness into the rear of the radio Plug the antenna into the antenna connector 8 Test for correct operation then slide the MS1500 fully into the mounting sleeve HEX NUT PLAIN WASHER SPRING WASHER TAPP
2. e Tl m m gt 0 m os CD PLAYER TROUBLESHOOTING WIRED REMOTE CONTROL REMMS1500 OPTION Mounting Remote Probl Possible Cause Corrective Action roblem The REMMS1500 comes with an aluminum mounting bracket that has 4 four notches cut Does not operate No power to yellow or red wire Inline fuse Check connection with test light check vehicle into it so the bracket can be broken away for different mounting depths blown fuse with test light Replace fuse No power to unit Inline fuse blown Replace fuse Speakers not operating Speaker harness not connected Connect speaker harness check speaker wires Not all speakers Incorrect splices or connections Speaker wires Check all splices and connections check splices operate shorting to chassis ground or to each other and insulate all bare wires Blows fuses Power wire shorting to ground Speaker wires Make sure wire is not pinched Install fuse of shorting to ground Incorrect too small a fuse correct rating CD skips too much Receiver mount is not solid or backstrap is not Check mounting and backstrap and tighten if secure ineeded Reload or press the Eject button check the ERROR 1 The disc is not loading or ejecting properly condition of the disk try another disk ERROR 2 An error in the laser reading the disc Ejec Make sure it is clean undamaged and loaded the disc correctly reload and check or try another disc Re
3. and regular play will resume The shuffle function will also be canceled by activating the scan or repeat functions CD CHANGER OPERATION FOR OPTIONAL ACC56M CHANGER TRACK UP DOWN 9 1 The Track Select function is used to quickly access the beginning of a particular track Press Track Up or Track Down to locate the desired track as shown by the track number indication on the LCD panel TRACK SEARCH High speed audible search to any section of the disc can be made by the search functions Press and hold the button to advance quickly in the forward direction or press and hold the button to advance rapidly in the backward direction During search operation the rotation disc symbol will turn faster and the appropriate symbol or will flash on the LCD panel When the Track Up is held and end of the last track is reached or the Track Down is held and the unit reaches the beginning of the first track on the disc the unit will enter the Pause mode until the button is released DISC UP DOWN BUTTON Press the DISC select button to select the desired disc for play as shown on the LCD panel The unit will automatically load the selected disc and begin play To advance to a higher number disc press the Preset 6 Disc Up button To return to a lower number press the Preset 5 Disc Down TRACK DISC SCAN SCN When the Preset 2 Scan button is pressed the indication SCN will appear on the LCD panel and the first 10 seconds of each trac
4. to Seek tuning mode AUTO will appear momentarily on the display Band Press BAND to change during radio play to switch between three FM bands and one AM band F1 F2 F8 or AM will appear in the display momentarily to indicate which band is currently selected Frequency Spacing U S frequency spacing is the default and a switch on the bottom of the chassis allows a change to European spacing Slide the switch to the desired setting using a small screwdriver blade then press RESET to activate the change 000 000000009000000000000000000000 Store and Recall a Station Up to 24 stations six on each band can be stored as presets This radio contains special circuitry which does not require a voltage source connected to the radio to maintain memories 1 To store a station select the desired band and station 2 Press and hold the desired preset button one through six for more than two seconds When stored the unit will beep and the preset number will appear in the display The station is now stored and can be re called at any time by momentarly pressing the corresponding preset button 3 Repeat for the remaining five presets on the current band and for all presets on the other bands Automatically Store Stations 1111 O Select six strong stations and store them in the current band using the Automatic Store AS feature To enable this feature press and hold AS PS for more than two seco
5. 9677 40Wx4 ue 11 16 VDC negative ground Speaker output impedance 4 ohms E E E E 10 amp fast blow ATO DIMENSIONS aeania USOS 7 x 6 47 64 x 2 W 178 x D 171 x H 50 mm The Mobile EXactonics AUDIOVOX SPECIALIZED APPLICATIONS 90 DAY 12 MONTH LIMITED WARRANTY AUDIOVOX SPECIALIZED APPLICATION LLG The Company wamamis to tha original retad purchaser of this product that should this product or any part thereof under normal and conditions be proven defective In material or workmanship within 90 day freen the dale of original purchase such delectis will be repaired replaced the Company s option without charge for parte and repair labor AMer Phe initia B days parod and a period of 12 months form the cate of original the Company will supply na charge a replacement for any dofective panja but will charge fer the labor repair the prodati obtain repas or replacement within the terms of this Warranty ASA must be called and Return Authorization will ba giren bo reference tha product when returned Tha product is 10 be delivered with pron of warranty coverage e g Dated ba of sale specification of defectis transportation prepaid and with the Authesization Number written on the eulaide of the package The product 11251 returnad to ASA for unless spacifiad etherwips
6. ASA This Warranty does not cover the elimination el pxlacrealhy generated state ar ta the correction of antenna problems 1o costs Incurred far remeval or reimstallatian e tha product or io damage in tapes speskers ar electrical ma Thia Warranty does not apply to amy product or part thereof which in the op nion of tne Company gas been damaged Through alteration improper mishandling misuse neglect ar accidet THE EXTENT OF THE COMPANY S LIABILITY UNDER THIS WARRANTY I LIMITED TO THE REPAIR OF REPLACEMENT PROVIDED ABOVE AND IN NO EVENT SHALL THE COMPANY S LIABILITY EXCEED THE PURCHASE PRICE PAID BY PURCHASE FOR THE PRODUCT This Warranty is in feu of all other express warrantias or ligbilitias ANY IMPLIED WARRANTIES INCLUDING IMPLIED WARRANTY OF MERCHANTABILITY SHALL BE LIMITED TO THE DURATION OF THIS WARRANTY ANY ACTION OR ANY BREACH OF ANY WARRANTY HEREUNDER INCLUDING ANY IMPLIED WARRANTY Of MERCHANTABILITY MUST BE BROUGHT WITHIN PEREOD OF 30 DAYS FROM DATE OF ORIGINAL PURCHASE IN NO CASE SHALL THE COMPANY FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES OR BREACH OF THES ANY OTHER WARRANTY EXPRESS OR IMPLIED WHATSOEVER NO person of representative is authorized to assume for ta Company liability other than expressad heroin connection with the sale of this product Some states do not allow limitations on hew long an warranty lasts or t
7. Equalizer Selector EQ Press EQ to apply sound effects to the unit s audio output signal When activated the EQ function will access one of the following modes CLASSICS POP M or ROCK M FLAT indicates no equalizer enhancements of the program thereby removing the preset sound effects DSP OFF inhibits selection of equalizer mode enhancement Reset Button The reset button is located on the front of the radio between MUTE and AS PS Reset should only be activated under the following circumstances 1 Upon initial installation after all wiring is completed 2 Upon malfunction of any switches on the unit Use a pencil or other non metallic object to press the reset button which will clear the system and restore normal operation Adjust Sound Press SEL to to step through the menu of audio functions The first option is volume VOL followed by bass BAS treble TRB balance BAL fader FAD and back to volume VOL VOL BASS 0 1 BAL 1 FAD Bass 1 Press SEL twice until BAS appears in the display 2 Press the volume buttons up or down to adjust Bass from 10 to 10 BAS 00 represents flat response The bass level will be shown on the display for five seconds or until another function is activated Treble 1 Press SEL three times until TRB appears in the display 2 Press the volume buttons up or down to adjust Treble from 10 to 10 TRB 00 represents flat response The treble l
8. ING SCREW MOUNTING SLEEVE 2 a gt 2 lt Ce 0 t BASIC OPERATION Power PWHR Press PWR or any other button except EJECT to turn the unit on Inserting a CD will turn the unit on automatically Press PWR to turn the unit off LCD Panel The Liquid Crystal Display LCD panel displays the frequency and all activated functions Note LCD panels may take longer to illuminate when subjected to cold temperatures for an extended period of time In addition the visibility of the numbers on the LCD may decrease slightly The LCD display will return to normal when temperature increases to a normal range Mode MODE Press MODE Radio CD Play CD Changer Aux to select a different mode of operation as indicated on the display panel During CD player operation pressing MODE will change to radio mode without ejecting the disc The CDP indication will remain in the display to show that a disc is still loaded in the unit Press MODE again to return to other mode Note The MS1500 is equipped with auxiliary audio input cables enabling you to connect a pre amp level external audio source directly to the head unit This allows you to listen to an auxiliary audio source on the vehicle speakers Loudness LOUD When listening to music at low volume levels this feature will boost the bass and treble ranges 1 Press and hold BAND LOUD for more than two second
9. ISC SHUFFLE SHF When the Preset 4 Shuffle button is pressed the indication SHF will appear on the LCD panel and the tracks on the disc will be played in a random shuffled order The Track Skip 5 function will also select tracks in the shuffled order instead of the normal progression The Track gt 0 m 2 Q D m gt lt Ce I Q Shuffle mode can be cancelled by pressing the Preset 4 Shuffle button again or by activating the Scan or Repeat functions When the Preset 4 Shuffle button is pressed and held longer than 2 seconds the SHF and DISC indications will appear on the LCD panel and the discs in the magazine will be played in a random shuffled order as well as the tracks on each disc When all the tracks on the selected disc have been played the next disc will be selected in shuffled order and its tracks will be played in shuffled order The Disc Shuffle mode can be cancelled by pressing the Preset 4 Shuffle button again or by activating the Scan or Repeat functions INSTALLATION OF THE OPTIONAL ACC56M CD CHANGER DATA CABLE 15 FEET Contact your marine dealer or ASA Electronics www asaelectronics com to obtain the ACC56M CD Changer 2 9 P
10. evel will be shown on the display for five seconds or until another function is activated Balance 1 Press SEL four times until BAL appears in the display 2 Press volume buttons up right or down left to adjust Balance between the right and leftspeakers from BAL 10R to BAL 101 BALL R represents an equal balance level between the right and left speakers The balance position will be shown on the display for five seconds or until another function isactivated Fader 1 Press SEL five times until FAD appears in the display 2 Press volume buttons up front or down rear to adjust Fader between the front and rear speakers from FAD 10F to FAD 10R FAD F R represents an equal balance between the front and rear speakers Ud gt gt 2 lt lt RADIO OPERATION Seek Tuning Press the up or down tuning button momentarily to seek the next strong station in the current band Manual Tuning 1 Press the up or down tuning buttons for more than two seconds to select manual tuning mode MANUAL will appear momentarily on the display 2 Press the up or down tuning buttons momentarily to move radio frequency up or down one step at a time 3 Press and hold the up or down tuning buttons to quickly advance to a certain frequency Release when the desired frequency is reached If manual tuning is not adjusted for five seconds the unit will return
11. he exclusion of incidanzal or consequential damages the above imilazions or axclusions may noi apply to yo This Warranty gives you legal rights and may have ether which vary from sabe to atate AUDIOVOX SPECIALIZED APPLICATIONS LLE ww xsaelectrnnips ncc P N PIAWARR
12. k on the disc will be played in order When a desired track is reached press the Preset 2 Scan button again and play of that track will continue SCN will disappear from the display Scan mode will be cancelled by activating any other function Repeat Shuffle Disc Up Down Track Up Down or Track Search When the Preset 2 Scan button is pressed and held for longer than 2 seconds the SCN and DISC indications will appear on the LCD panel and the first 10 seconds of the first track of each disc in the magazine will be played When a desired disc is reached press the Preset 2 Scan button again and play of that disc will continue SCN and DISC will disappear from the display Disc Scan mode will also be cancelled by activating any other function Repeat Shuffle Disc Up Down Track Up Down or Track Search TRACK DISC REPEAT RPT When the Preset 3 Repeat button is pressed the indication RPT will appear on the LCD panel and play of the selected track will be continuously repeated until the Repeat mode is cancelled by pressing the Preset 3 Repeat button again or by activating the Scan or Shuffle functions When the Preset 3 Repeat button is pressed and held longer than 2 seconds the RPT and DISC indications will appear on the LCD panel and play of the selected disc will be continually repeated until the Disc Repeat mode is cancelled by pressing the Preset 3 Repeat button again or by activating the Scan or Shuffle functions TRACK D
13. l reappear in the display Track Select 9 Track select features are used to quickly access the beginning of a particular track Press the up or down tuning button to move forward up tuning bottom or backward down tuning button on the disc to locate the desired track Track numbers will appear in the display as they are accessed Fast Forward and Fast Reverse Press and hold the up or down tuning buttons to fast forward or fast reverse a track During either function the elapsed time will appear on the display Release the button to resume CD play Pause Press PAUSE to freeze disc play S PAUSE will appear in the display for five seconds Press PAUSE again to resume disc play Scan During disc play press SCN to play the first 10 seconds to each track on the disc When the desired track is reached press SCN again to end the scan function and play the selected track The scan function will also be canceled by activating the repeat or shuffle functions Repeat RPT Press RPT during disc play to continuously repeat the selected track S RPT will appear in the display for five seconds Press RPT again to stop repeating and regular play will resume The repeat function will also be canceled by activating the scan or shuffle functions Shuffle Press SHF during disc play to play all tracks on a CD in random shuffled order S SHF will in the display for five seconds Press SHF again to stop random play
14. mote Operation The REMMS1500 operation is the same as functions on the front panel of the MS1500 Visit www asaelectronics com for technical assistance head unit See Pages 3 8 for detailed operation descriptions E J b u 9 9 y m 5 9 5 te Lu gt lt m Volume Down Volume Up Power Tune Track Up Tune track Down Mode Band 9 e Q v SPECIFICATIONS CD CD CHANGER gt 86dB Frequency NSO OMS ER UIN MM M MPH DUE 20Hz 20kHz Channel separation gt 65dB DA 68 11 14 1 Bit CH FM Tuner uei 87 5MHz 107 9MHz FM MT 12dBf quieting sensitivity stereo nene ni eiu Fa 16dBf Stereo Separation D 1KAZ 40dB 31 16 16124110 011 30Hz 13kHz 11116 ou E 530kHz 1710kHz Drs crudis M 30uV g ze ae aeq 80Hz 2kHz 3dB General Total system pOWer amd P 160 Watts Peak gioi OUlDU L 58
15. nds The radio will automatically scan the band in use and enter strong stations into the preset memory positions for that band The new stations replace stations already stored in that band Preset Scan 9 Press AS PS momentarily to scan the six preset stations in the current band The unit will stop at each station for 10 seconds before continuing to the next station The frequency will flash on the display during preset scan Press AS PS momentarily again to stop scanning and listen to the current station 2 p gt D m 2 2 lt tc Lui tc Q CD PLAYER OPERATION Insert CD With the label surface facing up gently insert the disc into the slot until the soft loading mechanism engages and disc play begins S CDP will appear in the display momentarily and the CD icon will become animated CDP will appear in the display momentarily with the track number and elapsed time Note The unit is designed for play of standard 5 12 cm compact discs only Do not attempt to use 3 8 cm CD singles in this unit either with or without an adaptor as damage to the player and or the disc may occur Such damage will not be covered by the warranty on this product Eject CD Press the eject button to stop CD play and eject the disc The unit will change to radio operation If the disc is not removed from the unit within 15 seconds the disc will be reloaded and SCDP wil
16. s to activate The unit will beep when this feature is activated and LOUD ON will appear in the display for five seconds LOUD will appear at the top of the display while this feature is activated 2 Press and hold BAND LOUD for more than two seconds to deactivate The unit will beep when this feature is activated and LOUD OFF will appear in the display for five seconds LOUD will no longer appear at the top of the display Volume The volume buttons up and down arrows increase and decrease the volume level of the unit To increase volume one level press the up arrow The volume will increase and the level VOL 00 to VOL 100 will appear in the display for five seconds or until another function is activated To increase the volume rapidly press and hold the up arrow until the desired volume level is reached To decrease volume one level press the down arrow The volume will decrease and the level VOL 00 to VOL 100 will appear in the display for five seconds or until another function is activated To decrease the volume rapidly press and hold the down arrow until the desired volume level is reached Mute Press MUTE to silence the audio volume from the system MUTE will flash in the display for five seconds To restore sound press MUTE again or activate any other function of the unit When the mute feature is deactivated the audio volume will return to the level setting in use before the mute feature was activated
Download Pdf Manuals
Related Search
Related Contents
Rejilla de seguridad luminosa comprobable TGS Kroy K2500 Thermal Label Printer ÄKTApurifier 10 to ÄKTApurifier 100 Upgrade kit American DJ Rolling Star User's Manual BENDIX 03-A-05E User's Manual Catálogo de Sistemas y Accesorios de Amarre para Vehículos y Adobe Captivate CS 5.5, Win, DVD, ENG View in new window Copyright © All rights reserved.
Failed to retrieve file