Behringer PMP5000 Musical Instrument User Manual
Contents
1. 20 dB PMP1000 The stereo channels 5 6 and 7 8 feature an additional XLR connector for microphones whose gain can be set from 0 to 40 dB Each stereo channel has two line level inputs 1 4 jacks for the left and right channels If only the jack marked L is used the channel is mono The signal will then be reproduced on both sides PMP1000 This does not apply to the mono stereo combination channels 5 6 and 7 8 2 CONTROL ELEMENTS 5 13 PMP1000 Channels 13 14 and 15 16 are routed to the main mix without additional tone or volume adjustment For example using the channels 13 14 and 15 16 you can connect a submixer and utilize the PMP1000 s power amplifier PMP3000 The stereo channels 9 10 and 11 12 are equipped with additional RCA connectors PMP5000 The stereo channels 13 14 and 15 16 are equipped with additional RCA connectors PMP3000 PMP5000 Please note that you need to set the A B selector to A 1 4 or B RCA when you connect a signal to the input PMP3000 PMP5000 Each of the two stereo channels has two monitor controls MON 1 2 and a LEVEL control 25 Like the other channels they also feature a PFL switch Instead of a fader this channel has a rotary LEVEL control The phantom power supply provides the voltage necessary for the operation of condenser microphones Use the PHANTOM switch to activate the supply for the XLR connectors of the input channels The 48 V LED will illuminate when2. Enable one or both processors with the FX1 2 IN buttons PMP3000 PMP5000 The FX 1 2 TO MON 1 control allows you to set the intensity of the multi effects processors in the monitor mix No effect is sent to the monitor mix when this control is set fully counter clockwise PMP1000 The FX TO MON control performs the same function as on the PMP3000 and PMP5000 The FX 1 2 TO MON 2 control allows you to determine the effect intensity of the multi effects processor in the monitor 2 mix No effect is sent to the monitor 2 mix with this control turned fully counter clockwise The FX 1 2 TO MAIN control allows you to determine the effect intensity of the multi effects processor in the main mix No effect is sent to the main mix with this control turned fully counter clockwise PMP1000 The FX TO MAIN control performs the same function as on the PMP3000 and PMP5000 gt A gt oy gt a amp EUROPOWER PMP1000 PMP3000 PMP5000 EXI 2 4 Main and monitor section The SURROUND control determines the effect intensity This is a built in effect which widens the stereo panorama thus making the sound more lively and transparent Press the XPQ TO MAIN switch to activate this effect Pressing the AFL switch after fader listening activates the solo function If AFL is on for the corresponding channel in the main section you will only hear the signal from this channel Its volume can be adjusted with the fader Switching AFL o
3. IMPORTANT NOTES CONCERNING INSTALLATION The sound quality may diminish within the range of powerful broadcasting stations and high frequency sources Increase the distance between the transmitter and the device and use shielded cables for all connections 1 1 3 Online registration Please do remember to register your new BEHRINGER equipment right after your purchase by visiting www behringer com alternatively www behringer de and kindly read the terms and conditions of our warranty carefully Should your BEHRINGER product malfunction our goal is to have it repaired as quickly as possible To arrange for warranty service please contact the retailer from whom the equipment was purchased Should your BEHRINGER dealer not be located in your vicinity you may directly contact one of our subsidiaries Corresponding contact information is included in the original equipment packaging Global Contact Information European Contact Information Should your country not be listed please contact the distributor nearest you A list of distributors can be found in the support area of our website www behringer com Registering your purchase and equipment with us helps us process your repair claims quicker and more efficiently Thank you for your cooperation 1 2 The manual This manual is designed to give you both an overview of all control elements and to provide details about how to use them To provide you with a clear structure we have grou
4. TEMP heen se sareas 4 1 1 3 Online registration n se eneee nenene reee 4 12 TE Mantal san 4 2 CONTROL ELEMENTS rennnennnnsevnnnnnennnsvennnnnennnnnennnn 5 2 1 Mono and stereo Channels cccccccececeeceeeeeeeeseeaeeaneees 5 21 1 Eee 5 22 Equalizer and FBQ sucinscsissasvoenencinccssnarcneveosnananareiersauwasonn 6 JERN SECON rer ri 2 4 Main and monitor section cseceseeeeeeeeeeeeesssseeeeeeees P 2 4 1 Cedar 8 2 9 Rear Dave EE 8 3 DIGITAL EFFECTS PROCESSOR mmnnnnnnnnnnnnnnnnnnnnnnnnner 8 4 INSTALLATION Haa 9 21 Mains COMET arret 9 4 2 Audio CONNectiOnS 1arereagreukenelereadaietiadee 9 4 3 Loudspeaker connections ccccccceeceeeeeeeeeeeeeeeaeeaneens 10 5 WIRING EXAMPLES ciivsssscscssceisesescsctssawcenasvnvsveanesasanws 11 6 SPECIFICATIONS susen 14 7 WARRANTY sis ccucencsienccteneticicivencensicivenenecncivsnewietedeenes 16 FCC FEDERAL COMMUNICATIONS COMMISSION COMPLIANCE INFORMATION evvvnnnnnnnnnnnnnnnnnnnnnnennnn 17 CAUTION I We would like to point out that high volume levels may damage your hearing and or your headphones Please move down all faders in the MAIN section before turning on the device Always make sure that the appropriate volume is set 1 INTRODUCTION Congratulations With the PMP1000 PMP3000 PMP5000 you have acquired a state of the art power mixer that sets new standards Right from the very start it has been our goal to design a revolutionary unit that can be
5. normal output power In BRIDGE mode always connect only one loudspeaker with an impedance of at least 8 Q to the OUTPUT B jack Please note that OUTPUT A must NEVER be used in BRIDGE mode In all other operating modes the minimum impedance of the speaker must not fall below 4 Q EUROPOWER PMP1000 PMP3000 PMP5000 I Please note that the power delivered to the speaker connected to OUTPUT B in BRIDGE AMP MODE is considerably higher than the power provided to the speakers wired to the parallel speaker outputs Please read the information given on the rear panel of the power mixer Information on how to properly connect your speaker with regard to polarity can be found on the rear of the unit PIN assignment see also and 72 PMP5000 Use the BEHRINGER SPEAKER PROCESSING switch to activate a filter that allows you to adapt the mixer to the characteristics of your loudspeakers If the speakers have a limited frequency response in the bass range this function allows you to filter this range at the output signal of the mixer and thus adapt it optimally to the frequency response of the speakers PMP1000 PMP5000 If STANDBY is pressed all input channels are muted During pauses you can prevent the microphones from picking up noise or interference which would then be reproduced by the P A system or possibly damage the speaker diaphragms The benefit is that all faders can be left untouched while you play back music from C
6. phantom power is on In most cases dynamic microphones can still be used as long as they are connected in a balanced configuration If in doubt please contact the manufacturer of your microphone With phantom power switched on you must never connect microphones to the console or to a stage wall box Also be sure to mute the monitor P A speakers before you turn on the phantom power supply After switching on please allow the system to stabilize for about one minute before you adjust the input gain Caution Never use unbalanced XLR connectors pins 1 and 3 interconnected on the MIC input jacks if you are going to use the phantom power supply The AMP MODE switch determines the mode of operation of the PMP amplifier stage PMP1000 MAIN In the MAIN position the mixer works as a stereo amplifier MON In this mode the monitor signal is present at OUTPUT A and the main signal at OUTPUT B both are mono BRIDGE bridged mono mode In BRIDGE AMP MODE the output power of OUTPUT A is added to that of OUTPUT B i e OUTPUT B delivers twice its normal output power PMP3000 PMP5000 MAIN L MAIN R In position MAIN MIX the mixer works as a stereo amplifier MON 1 MONO In this mode the monitor 1 signal is present at OUTPUT A and the main signal at OUTPUT B both are mono BRIDGE bridged mono mode In BRIDGE AMP MODE the output power of OUTPUT A is added to that of OUTPUT B i e OUTPUT B delivers twice its
7. project can be proud of what we ve achieved It is our philosophy to share our joy with you because you are the most important member of the BEHRINGER team With your highly competent suggestions for new products you ve greatly contributed to shaping our company and making it successful In return we guarantee you uncompromising quality as well as excellent technical and audio properties at an extremely favorable price All of this will enable you to fully unfold your creativity without being hampered by budget constraints We are often asked how we can make it to produce such high grade devices at such unbelievably low prices The answer is quite simple it s you our customers Many satisfied customers means large sales volumes enabling us to get better conditions of purchase for components etc Isn t it only fair to pass this benefit back to you Because we know that your success is our success too would like to thank all people whose help on Project PMP has made it all possible Everybody has made very personal contributions starting from the designers of the unit to the many staff members in our company and finally to you the user of BEHRINGER products My friends it s been worth the trouble Thank you very much Uli Behringer TABLE OF CONTENTS 1 INTRODUCTION ssscsiicstvcccnvsiaccsssavescsdetresesvetesnnsescesctecis 4 1 1 Before you get started rrnnnnnnnonvonnnonvnonnnnnvnnnvnnennevnvenne 4 Ne 4
8. the buyer or his authorized dealer must call BEHRINGER see enclosed list during normal business hours BEFORE returning the product All inquiries must be accompanied by a description of the problem BEHRINGER will then issue a return authorization number 2 Subsequently the product must be returned in its original shipping carton together with the return authorization number to the address indicated by BEHRINGER 3 Shipments without freight prepaid will not be accepted 5 WARRANTY REGULATIONS 1 Warranty services will be furnished only if the product is accompanied by a copy of the original retail dealer s invoice Any product deemed eligible for repair or replacement under the terms of this warranty will be repaired or replaced EUROPOWER PMP1000 PMP3000 PMP5000 2 If the product needs to be modified or adapted in order to comply with applicable technical or safety standards on a national or local level in any country which is not the country for which the product was originally developed and manufactured this modification adaptation shall not be considered a defect in materials or workmanship The warranty does not cover any such modification adaptation irrespective of whether it was carried out properly or not Under the terms of this warranty BEHRINGER shall not be held responsible for any cost resulting from such a modification adaptation 3 Free inspections and maintenance repair work are expressly excluded from t
9. with the manufacturer s instructions 8 Do not install near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat 9 Do not defeat the safety purpose of the polarized or grounding type plug polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade or the third prong are provided for your safety If the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet 10 Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus 11 The apparatus shall be connected to a MAINS socket outlet with a protective earthing connection 12 Where the MAINS plug or an appliance coupler is used as the disconnect device the disconnect device shall remain readily operable 13 Only use attachments accessories specified by the manufacturer 14 Use only with the cart stand tripod bracket or table specified by the manufacturer or sold with the apparatus When a cart is used use caution when moving the cart apparatus combination to avoid injury from tip over ATT 15 Unplug this apparatus during lightning storms or when unused for long periods of time 16 Refer all servicing to qualified service personnel Servicing is required when the a
10. 1 4 jacks to RCA connectors and vice versa Position A 1 4 jacks position B RCA connectors The HIGH control in the EQ section governs the high frequency range of the respective channel Use the MID control to boost or cut the midrange frequencies PMP5000 The PMP5000 has an additional semi parametric filter for the midrange frequencies in the mono channels tunable from 100 Hz to 8 kHz Adjust the boost cut with the MID control and the frequency with the FREQ control The stereo channels contain a stereo EQ section The cut off frequencies of the high and low bands are 12 kHz and 80 Hz respectively while the center frequencies of the high mid and low mid bands are 3 kHz and 400 Hz respectively The LOW control allows you to boost cut the low frequency range With the MON ITOR control you can adjust the volume of each channel in the monitor mix The PMP3000 and PMP5000 feature a second MON control MON 2 for the volume of the second monitor bus The FX control determines the signal level sent from each channel to the built in effects processor this signal is also present at the FX SEND jack see 64 The PMP5000 has two FX controls FX 7 and FX 2 so that you can use two effects simultaneously Accordingly the PMP5000 also has two effect aux buses which have one output jack in common see and 64 Please note that the effects processor signal will be inaudible as long as the FX TO MON MAIN
11. D via the CD TAPE inputs see 55 There is also no need to move the faders and lose your mix 2 2 Equalizer and FBQ Your power mixer features a graphic 7 band equalizer which allows you to fine tune the sound depending on the room acoustics In the center position the frequency response is not effected To boost or cut a certain frequency range simply move the corresponding fader upward or downward respectively Please note that the equalizer behaviour depends on the position of the AMP MODE switch see 27 VI SV equalizer before Frequencies causing feedback are shown by brightly lit fader LEDs All other LEDs will be darker Now cut the frequency range in question until feedback disappears the LED gets darker or goes out This function is available for both the main and monitor mix PMP1000 The switch FBQ FEEDBACK DETECTION performs the same function as on the PMP3000 and PMP5000 Use the MAIN MON 1 switch to select whether the equalizer processes the main or the monitor mix When not pressed the stereo equalizer processes only the main mix When the switch is pressed the EQ processes only the monitor mix PMP1000 The MAIN MIX MONITOR switch performs the same function as on the PMP3000 and PMP5000 Press the FBQ IN switch to activate the Feedback Detection system the FBQ will be active only if you have switched on the Press the EQ N switch to activate the equalizer The fader LEDs illuminate when the E
12. Fig 4 1 4 TS connector Balanced 1 4 TRS connector sleeve tip strain relief clamp ground shield hot ve sleeve i ring ring cold ve abo For connection of balanced and unbalanced plugs ring and sleeve have to be bridged at the stereo plug Fig 4 2 14 TRS connector 4 INSTALLATION Balanced XLR connectors input output 1 ground shield 2 hot ve 3 cold ve D For unbalanced use pin 1 and pin 3 have to be bridged Fig 4 3 XLR connectors 1 4 TS footswitch connector sleeve strain relief clamp pole 1 ground sleeve tip u The footswitch connects both poles momentarily Fig 4 4 14 mono plug for footswitch Power amp insert send return 1 4 TRS connector sleeve tip strain relief clamp ground shield return in sleeve ring ring send out tip pairs Connect the insert send with the input and the insert return with the output of the effects device Fig 4 5 Stereo 1 TRS connector for power amp ISR connection EUROPOWER PMP1000 PMP3000 PMP5000 4 3 Loudspeaker connections Your power mixer is equipped with high quality loudspeaker OUTPUT B OUTPUT A connectors compatible to Neutrik Speakon which ensure safe and trouble free operation The Speakon connector was especially developed for high power loudspeakers Once it is plugged in it safely locks into position and cannot be accidentally disengaged It prevents the occurrence of e
13. Q is on Use this LED display to control the output level of the main signal The upper L M LED illuminates when the internal amp protection circuit responds to levels that are too high PMP1000 The POWER LED is illuminated when you switch the unit on The LIM LEDs and the LED display do NOT light up when an external signal is fed in via the PWR AMP INSERT jacks 61 2 CONTROL ELEMENTS 2 3 Effects section List of all multi effects processor presets The LED level meter on the effects module should always show a sufficiently high level Make sure that the Clip LED illuminates with signal peaks only If it is constantly illu minated the effects processor is overloading which can lead to unpleasant distortion The FX SEND fader PMP 1000 or FX FX 1 2 fader PMP3000 PMP5000 controls the level sent to the effects module and to the FX SEND output jacks The effects display always reads the currently selected preset PMP3000 PMP5000 Press the FX1 2 IN switch to activate the effects processor PMP1000 PMP3000 Turn the PROGRAM control to select an effects algorithm preset number starts flashing Press this control to activate the effect selected PMP5000 FX 1 2 PUSH PMP1000 The effects processor is operative all the time Adjust the effect intensity for the MAIN or MON signals with controls or respectively PMP5000 The PMP5000 has two separate effects processors which can be used independently of one another
14. RINGER by any express or implied undertaking or representation No part of this manual may be reproduced or transmitted in any form or by any means electronic or mechanical including photocopying and recording of any kind for any purpose without the express written permission of BEHRINGER International GmbH BEHRINGER is a registered trademark ALL RIGHTS RESERVED 2006 BEHRINGER International GmbH Hanns Martin Schleyer Str 36 38 47877 Willich M nchheide II Germany Tel 49 2154 9206 0 Fax 49 2154 9206 4903 16 7 WARRANTY FEDERAL COMMUNICATIONS COMMISSION COMPLIANCE INFORMATION BEHRINGER EUROPOWER PMP1000 3000 5000 Responsible party name BEHRINGER USA Inc Address 18912 North Creek Parkway Suite 200 Bothell WA 98011 USA Phone Fax No Phone 1 425 672 0816 Fax 1 425 673 7647 hereby declares that the product EUROPOWER PMP1000 3000 5000 complies with the FCC rules as mentioned in the following paragraph This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will no
15. User Manual Version 1 0 November 2006 Cisis eoo 1051051040 0 10 10 0010 4 Ege 1Q21O 10 O p ssid tt 7 a e oe oo o eo ow on ox a K BEHRINGER www behringer com JUST LISTEN EUROPOWER PMP1000 PMP3000 PMP5000 EUROPOWER PMP1000 PMP3000 PMP5000 IMPORTANT SAFETY INSTRUCTIONS CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN ATTENTION RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR CAUTION To reduce the risk of electric shock do not remove the top cover or the rear section No user serviceable parts inside refer servicing to qualified personnel WARNING To reduce the risk of fire or electric shock do not expose this appliance to rain and moisture The apparatus shall not be exposed to dripping or splashing and no objects filled with liquids such as vases shall be placed on the apparatus This symbol wherever it appears alerts you to the presence of uninsulated dangerous voltage inside the enclosure voltage that may be sufficient to constitute a risk of shock This symbol wherever it appears alerts you to important operating and maintenance instructions in the accompanying literature Please read the manual 1 Read these instructions 2 Keep these instructions 3 Heed all warnings 4 Follow all instructions 5 Do not use this apparatus near water 6 Clean only with dry cloth 7 Do not block any ventilation openings Install in accordance
16. a DISPLAY EE Type dual 7 segment LED AMPLIFIER 2 dual 7 segment LED RMS Q 1 THD sine wave both channels driven RMS Q 1 THD sine wave bridged mode Mains voltage 100 240 V 50 60 Hz 230 V 50 Hz 500 W 1000 W U O m J no Cc U U m lt Ti E T 6 3 A H 250 V Standard IEC receptacle 120 V 60 Hz 1000 W T 10A H250V Standard IEC receptacle 100 240 V 50 60 Hz 100 V 50 60 Hz 1000 W T 10A H250V Standard IEC receptacle 220 V 50 Hz 1000 W T 6 3 A H 250 V Standard IEC receptacle 4 7 8 x 15 3 8 x 16 3 4 4 7 8 x 18 3 4 x 18 1 8 4 7 8 x 23 1 2 x 19 1 2 Dimensions H x W x D 122 x 390 x 425 mm 122 x 476 x 460 mm 122 x 596 x 496 mm Weight 15 435 Ib 23 815 Ib 28 665 Ib 10 8 kg 13 3 kg BEHRINGER is constantly striving to maintain the highest professional standards As a result of these efforts modifications may be made from time to time to existing products without prior notice Specifications and appearance may differ from those listed or illustrated 6 SPECIFICATIONS 15 7 WARRANTY 1 OTHER WARRANTY RIGHTS AND NATIONAL LAW 1 This warranty does not exclude or limit the buyer s statutory rights provided by national law in particular any such rights against the seller that arise from a legally effective purchase contract 2 The warranty regulations mentioned herein are applicable unless they constitute an infringement of national wa
17. al damage which may have occurred during transit I If the unit is damaged please do NOT return it to BEHRINGER but notify your dealer and the shipping company immediately Otherwise claims for damage or replacement may not be granted I We recommend that you use a flight case so as to give your power mixer optimum protection during use or transport I Always use the original packing carton to prevent damage during storage or transport Make sure that children cannot play unsupervised with the device or its packaging I Please ensure proper disposal of all packing materials EUROPOWER PMP1000 PMP3000 PMP5000 1 1 2 Initial operation Be sure that there is enough air space around the unit for cooling and to avoid overheating please do not place the EUROPOWER near radiators etc I Blown fuses must be replaced by fuses of the same type and rating Please refer to the SPECIFICATIONS for details The mains connection is made using the enclosed power cord and a standard IEC receptacle It meets all of the international safety certification requirements I Please make sure that all units have a proper ground connection For your own safety never remove or disable the ground conductor from the unit or on the AC power cord To avoid damage on the device do not earth the loudspeaker outputs connect the loudspeaker outputs to each other connect the loudspeaker outputs to those of other amplifiers
18. al voltage Blown fuses should only be replaced by fuses of the same type and rating Please also read the information given in the SPECIFICATIONS Use the POWER switch to put your PMP into operation The POWER switch should always be in the Off position before connecting your unit to the mains Please note The POWER switch does not fully disconnect the unit from the mains Unplug the power cord completely when the unit is not used for prolonged periods of time SERIAL NUMBER This is where you find the cooling fan of the unit The PMP5000 has two cooling fans OUTPUT A LEFT provides either the left stereo main signal or the monitor signal in mono depending on the operating mode selected see 27 NEVER use this output in bridged mono mode OUTPUT B RIGHT BRIDGE provides either the right stereo main signal the main mix signal mono or the bridged mono signal depending on the operating mode selected In BRIDGE mode always connect only one loudspeaker with an impedance of at least 8 Q to the OUTPUT B jack NEVER use OUTPUT A in BRIDGE mode In all other operating modes the impedance of the connected loudspeaker must not fall below 4 Q 3 DIGITAL EFFECTS PROCESSOR 24 BIT MULTI EFFECTS PROCESSOR This built in effects module produces high grade standard effects such as reverb chorus flanger delay and various combination effects The integrated effects module has the advantage of requiring no wiring Th
19. also 59 which is the same signal as at MAIN 1 but with extra output jacks and separate volume control PMP3000 PMP5000 With the CD TAPE IN control you can adjust the volume of the line signal present at the CD TAPE INPUT 55 Use the PFL switch to monitor the signal PMP1000 With the CD TAPE RET fader you can adjust the line signal applied to the CD TAPE INPUT 55 Use the CD TAPE MUTE switch to mute the channel 2 CONTROL ELEMENTS 7 2 4 1 Connectors Use the CD TAPE INPUT jacks RCA to connect an external stereo signal such as a CD player tape deck or other line level sources wear The VOICE CANCELLER filters vocal specific Malena frequencies from the CD TAPE INPUT signal This function can be used for karaoke i e you can remove the vocals from a song and then sing along with the music yourself The CD TAPE OUTPUT provides the line level stereo signal e g for a DAT recorder If the CD TAPE OUT signal is connected to a recording machine whose output signal is returned to the CD TAPE IN feedback can occur when you activate the record function on the recording machine So disconnect the CD TAPE IN from the recording machine before you start recording or set the CD TAPE input signal to zero PMP1000 The MAIN OUT jacks allow you to send the main line level signal to an external amplifier when for example you want to use the mixer and effects section The PMP3000 and PMP5000 have two separately controllable l
20. ame time just wire the connector s ring and tip together The FOOTSWITCH jack is for a standard footswitch You can activate an effect bypass thereby muting the effects processor Use a dual foot switch for the PMP5000 so that you can enable disable FX1 and FX2 independently of each other In this case the tip of the 1 4 plug controls FX1 and the ring FX2 PMP3000 PMP5000 The MONO OUT is for connecting a subwoofer The PMP5000 has the additional possibility of setting the low frequency range for the subwoofer Use the SUB FILTER control to adjust the frequency EUROPOWER PMP1000 PMP3000 PMP5000 The FX SEND connector can be used to route the FX SEND signal from the input channel for example to the input of an external effects device Since the PMP5000 has two FX controls per input signal see 12 both FX SEND 1 2 are present at one jack Please note The SEND signal is in parallel with the FX SEND jacks and with the effects processor so that both can be controlled together by one control For the FX signals use a 1 4 stereo plug connected as follows FX1 tip FX2 ring The PHONS CTRL connector allows you to connect a pair of stereo headphones or an active monitor speaker 2 5 Rear panel The mains connection is via a standard IEC receptacle An appropriate power cord is supplied with the unit FUSE HOLDER Before connecting the unit to the mains ensure that the voltage setting matches your loc
21. controls 40 41 are set fully counter clockwise The PAN ORAMA control determines the position of the channel signal in the stereo main mix The BAL ANCE control for the stereo channels corresponds to the PAN control for the mono channels It determines the relative volume of the left and right input signals before they are routed to the stereo main output PMP3000 PMP5000 When you press the PFL button Pre Fader Listening the left LED shows the pre fader input gain of the channel Adjust the optimum input gain 0 dB with the TRIM control 1 When PFL is on the corres ponding LED illuminates If the LEVEL SET LED is illuminated constantly the signal is within the optimum operating level range However if the CLIP LED indicates that the input gain is too high you should reduce the level slightly with the TRIM control The CLIP LED should never be illuminated all the time only with signal peaks The MUTE switch mutes the channel in the main mix The pre fader signals monitor buses remain operative When MUTE is pressed the corresponding control LED illuminates The channel fader controls the channel signal level in the main mix 2 1 1 Input section Each mono input channel is equipped with a balanced microphone input XLR connector which provides 48 V phantom power for condenser microphones at the touch of a button see rear panel PMP1000 The two stereo channels 5 6 and 7 8 have an additional balanced XLR
22. his warranty in particular if caused by improper handling of the product by the user This also applies to defects caused by normal wear and tear in particular of faders crossfaders potentiometers keys buttons tubes guitar strings illuminants and similar parts 4 Damages defects caused by the following conditions are not covered by this warranty A improper handling neglect or failure to operate the unit in compliance with the instructions given in BEHRINGER user or service manuals A connection or operation of the unit in any way that does not comply with the technical or safety regulations applicable in the country where the product is used A damages defects caused by force majeure or any other condition that is beyond the control of BEHRINGER 5 Any repair or opening of the unit carried out by unauthorized personnel user included will void the warranty 6 If an inspection of the product by BEHRINGER shows that the defect in question is not covered by the warranty the inspection costs are payable by the customer 7 Products which do not meet the terms of this warranty will be repaired exclusively at the buyer s expense BEHRINGER will inform the buyer of any such circumstance If the buyer fails to submit a written repair order within 6 weeks after notification BEHRINGER will return the unit C O D with a separate invoice for freight and packing Such costs will also be invoiced separately when the buyer has sent
23. in a written repair order 6 WARRANTY TRANSFERABILITY This warranty is extended exclusively to the original buyer customer of retail dealer and is not transferable to anyone who may subsequently purchase this product No other person retail dealer etc shall be entitled to give any warranty promise on behalf of BEHRINGER 7 CLAIM FOR DAMAGES Failure of BEHRINGER to provide proper warranty service shall not entitle the buyer to claim consequential damages In no event shall the liability of BEHRINGER exceed the invoiced value of the product Customers in the European Union please contact BEHRINGER Germany Support for further details Technical specifications and appearance subject to change without notice The information contained herein is correct at the time of printing The names of companies institutions or publications pictured or mentioned and their respective logos are registered trademarks of their respective owners Their use neither constitutes a claim of the trademarks by BEHRINGER nor affiliation of the trademark owners with BEHRINGER BEHRINGER accepts no liability for any loss which may be suffered by any person who relies either wholly or in part upon any description photograph or statement contained herein Colours and specification may vary slightly from product Products are sold through our authorised dealers only Distributors and dealers are not agents of BEHRINGER and have absolutely no authority to bind BEH
24. ine level MAIN outputs MAIN 1 2 Connect your monitor power amps or active monitor speakers to the MON 1 2 SEND to monitor the signal mix created with the MON controls or to route it to the musicians on stage The PMP Series comes with a POWER AMP INSERT connection that is provided for various applications This connection enables you to use the power amplifier of the device to amplify the output signal of another preamp For example it is possible to connect a larger mixer or preamp output line signal of an instrument amplifier In this case you only need an unbalanced mono jack cable Furthermore it is possible to use the POWER AMP INSERT as a conventional insert to add a compressor or graphic equalizer to the signal path for instance Here a balanced stereo jack cable is required and the assignment of tip and ring needs to be observed according to Figure 4 5 see Chapter 4 2 Audio Connections In this case the ring is the so called Send which is connected to the input of the additional device and the tip is referred to as Return which is connected to the output of the additional device Lastly it is possible to tap the output signal of the device s mixer section from the POWER AMP INSERT in order to use a second external power amp A balanced stereo jack cable is required with the ring not the tip connected to the input of the external power amp If you want to use the internal and external power amps at the s
25. is way the danger of creating ground loops or uneven signal levels is eliminated at the outset completely simplifying the handling These effect presets are designed to be added to dry signals 13 Turn down the FX controls in those channel strips whose signals you don t wish to process 3 DIGITAL EFFECTS PROCESSOR EUROPOWER PMP1000 PMP3000 PMP5000 4 INSTALLATION 4 1 Mains connection The mains connection is made using the enclosed power cord and a standard IEC receptacle It meets all of the international safety certification requirements Blown fuses must be replaced by fuses of the same type and rating I Please make sure that all units have a proper ground connection For your own safety never remove or disable the ground conductor from the unit or of the AC power cord 4 2 Audio connections The inputs and outputs of your BEHRINGER EUROPOWER are unbalanced 1 4 mono jacks except for the mono channel line inputs which are balanced 1 4 stereo jacks Of course all inputs and outputs work with both balanced and unbalanced connectors The tape in and outputs are on RCA connectors 13 Please ensure that only qualified personnel install and operate the PMP During installation and operation the user must have sufficient electrical contact to earth Electrostatic charges might affect the operation of the unit Unbalanced 1 4 TS connector sleeve ground shield strain relief clamp sleeve tip EES
26. lectrical shock and ensures the correct polarity Each of the loudspeaker jacks carries only the assigned single signal see the information given on the rear panel of the power mixer Speaker connector compatible with Neutrik Speakon connector BRIDGE Fig 4 7 Speakon pin assignment Fig 4 6 Professional speaker connector with polarity allocation Please be sure to only use commercial Speakon cables type NL4FC for connecting your loudspeakers to the power mixer Please check the pin assignment of your loudspeakers and cables dependent on the PMP speaker output you choose man x x wonror x mono x oureurs x x E o MANR x x PP mono x x Jf mono x x P BRIDGE x J xl Tab 4 1 Polarity configuration of speaker connectors 10 4 INSTALLATION EUROPOWER PMP1000 PMP3000 PMP5000 5 WIRING EXAMPLES Loudspeaker connection monitor mix PMP1000 PMP3000 PMP5000 part view 2 x BEHRINGER EUROLIVE Stack B1500 amp B1020 both passive Loudspeaker connection monitor mix front panel part view FX FOOTSW MON SEND Footswitch Link output 2 x BEHRINGER B300 active Fig 5 1 Stereo operation For stereo operation the POWER AMP switch must be set to its upper position MAIN or MAIN L MAIN R Outputs A and B provide the stereo main signal for passive speakers The preamp monitor output is c
27. microphone input with 48 V phantom power Be sure to switch off your audio system before you activate the phantom power supply to protect your monitor speakers from switch on thumps Each mono input features one LINE IN connector 1 4 jack which can be used with either balanced or unbalanced signals Please remember to use either the microphone or the line input on a specific channel Never use both at the same time When you connect a mono line signal to a stereo channel always use the left input The mono signal will then be reproduced by both sides equally PMP1000 This does not apply to the mono stereo combination channels 5 6 and 7 8 INSERT I O Insert points or simply inserts are used to process a signal with dynamic processors or equalizers They are pre fader pre EQ and pre MON FX SEND Unlike reverb and other effects which are usually added to the dry signal dynamic processors usually process the entire signal So aux send buses are not the best solution Dynamic processors need to be inserted directly into the signal path Once processed the signal then returns to the mixing console at the same point where it left Signal interruption takes place only if a plug is inserted into the corresponding jack 1 4 stereo plug tip signal output ring input All mono input channels are equipped with inserts The stereo channels have a TRIM control for gain adjustment with the input sensitivity ranging from 20 to
28. n has no effect on the main or monitor mix as long as you don t move the fader In this way you can monitor one or several selected signals via the PHONES CTRL jack 65 When AFL is on the corresponding control LED illuminates The PMP1000 does not have an AFL function PMP1000 FX SEND fader PMP3000 FX fader PMP5000 FX 1 2 fader This is the master send fader for the signal routed to the effects processor and to the FX SEND output see also and 12 PMP1000 MON SEND fader PMP3000 PMP5000 MON 1 2 fader These faders are used to set the monitor output volume see also 9 and 10 PMP1000 The main mix allows you to control the volume from the Main 1 output with both faders PMP3000 PMP5000 The MAIN 1 fader controls the volume of the EUROPOWER The main signal is also provided at the MAIN 1 output see also 53 PMP3000 PMP5000 The MONO fader controls the mono mix signal see also 63 PMP5000 The SUB FILTER filters out frequencies above the selected setting so that only low frequencies are sent to an active subwoofer via the MONO OUT 63 Set this switch to On to activate the filter PMP5000 The SUB FREQ control determines the cut off frequency for the subwoofer output This value can be adjusted from 30 to 200 Hz The PHONS CTRL R control adjusts the headphone or control room volume see also 65 PMP3000 PMP5000 The MAIN 2 control determines the volume at the MAIN 2 output see
29. onnected to two parallel active speakers which are used as on stage monitors Use the footswitch to enable disable the effects processor Subwoofer Monitor mix OUTPUT B OUTPUT A MONITOR LEFT PMP1000 PMP3000 l PMP5000 7 Rear panel EUROPOWER EP1500 EUROLIVE EUROLIVE B1520 B1520 EUROLIVE B1500X subwoofer 2 x BEHRINGER B300 active Fig 5 2 Bridged mono operation This illustration shows the power mixer with a sub woofer connected to OUTPUT B For a bridged mono operation to OUTPUT B the AMP MODE selector switch must be set to its lower position BRIDGE A separate stereo power amp BEHRINGER EUROPOWER EP1500 connected to the preamp main outputs delivers the stereo main signal Two active monitor speakers for on stage operation are connected to the preamp monitor output 5 WIRING EXAMPLES 11 EUROPOWER PMP1000 PMP3000 PMP5000 Loudspeaker connection for F O H and monitor mix mono MIN LOADS OUTPUT 0 SPEAKER 4 8 BRIDGE 8 16 J OUTPUT B OUTPUT A RIGHT BRIDGE LEFT B BRIDGE POS 1 1 B POS 2 NEG 2 jJ PMP1000 PMP3000 PMP5000 Rear panel excerpt 2 x BEHRINGER EUROLIVE F1520 passive 2 x BEHRINGER EUROLIVE B1520 passive Fig 5 3 Dual mono operation For a dual mono operation the AMP MODE switch must be set to its center position MON1 MONO for PMP3000 PMP5000 or MON for PMP1000 The two l
30. oudspeaker outputs provide the main and the monitor signals separately from each another Each of these signals is then sent to two speakers wired in parallel Keyboard Electric guitar Mono channel 5 10 BG lt wT Ms aft Send in Se 1 1x8 la Fig 5 4 Standard set up example The illustration shows just one channel configuration possible comprising mono and stereo sources and additionally the tape input output for recording the mix signal or feeding in a playback signal 12 5 WIRING EXAMPLES EUROPOWER PMP1000 PMP3000 PMP5000 BEHRINGER BEHRINGER EUROLIVE B1220 EUROLIVE B1220 PMP1000 PMP3000 BEHRINGER PMP5000 BEHRINGER EUROLIVE B1800x Rear panel EUROLIVE B1800X TETE z OUTPUT A LEFT A B POS 1 Be NEG 1 gt Output B Output A BEHRINGER Relive Vocals voice Drums percussion EUROPOWER EP1500 subwoofer ff BEHRINGER BEHRINGER B 2 L MAIN 1 OUT XM1800S oa zm ma O U _ WM output EUROPOWER yer Peta o en e lin OOJ Or je MON O N oN Ay I l N A ce N A G N apel 1006 Swi _ D Ved D s 7 e AO 1020 OJI C MULTI O U T J Gp J US Y R OP ar LINE IN UNE IN LINE IN UNE IN LINE IN LNE N Jat val pe o HR vil om ia vil om uf us Er an ee ay fa INSERT INSERT AA INSERT g INSERT
31. ped the control elements according to their function They can easily be found on the enclosed numbered illustrations If you need more detailed information on specific topics please visit our web site at www behringer com 4 1 INTRODUCTION EUROPOWER PMP1000 PMP3000 PMP5000 2 CONTROL ELEMENTS A detailed description of all functions of your power mixer can be found in the following chapters Please also refer to the enclosed sheet with the numbered illustrations to get a good overview of the control layout le O N 2 1 Mono and stereo channels Use the TRIM control to adjust the input gain Be sure to set this control fully counter clockwise before you connect or disconnect a signal source to an input TRIM controls both the microphone and the LINE input The black scale shows the microphone gain 10 to 60 dB on channels with XENYX MIC PREAMPS and 0 to 40 dB on conventional microphone inputs PMP1000 only channels 5 6 and 7 8 The LINE scale indicates the sensitivity of the LINE input ranging from 10 to 40 dBu PMP1000 The mono stereo combination channels 5 6 and 7 8 have a sensitivity of 20 to 20 dBu The LEVEL SET LED illuminates when an optimum operating level has been adjusted The mono channels are equipped with a high slope LOW CUT filter eliminating unwanted low frequency signals like rumble noise PMP3000 PMP5000 stereo channels Press the A B button to switch from
32. pparatus has been damaged in any way such as power supply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped 17 CAUTION These service instructions are for use by qualified service personnel only To reduce the risk of electric shock do not perform any servicing other than that contained in the operation instructions unless you are qualified to do so EUROPOWER PMP1000 PMP3000 PMP5000 FOREWORD Dear Customer Welcome to the team of EUROPOWER users and thank you very much for expressing your confi dence in BEHRINGER products by purchasing this power mixer It is one of my most pleasant tasks to write this letter to you because it is the culmination of many months of hard work delivered by our engineering team to reach a very ambitious goal to present you three outstanding power mixers that give you maximum flexibility and performance with a unique sound character and broad range of striking functions The task to design the new PMP series certainly meant a great deal of responsibility which we assumed by focusing on you the discerning user and musician It also meant a lot of work and night shifts to accomplish this goal But it was fun too Developing a product usually brings a lot of people together and what a great feeling it is when everybody who participated in such a
33. rranty law 2 ONLINE REGISTRATION Please do remember to register your new BEHRINGER equipment right after your purchase by visiting www behringer com alternatively www behringer de and kindly read the terms and conditions of our warranty carefully Registering your purchase and equipment with us helps us process your repair claims quicker and more efficiently Thank you for your cooperation 3 WARRANTY 1 BEHRINGER BEHRINGER International GmbH including all BEHRINGER subsidiaries listed on the enclosed page except BEHRINGER Japan warrants the mechanical and electronic components of this product to be free of defects in material and workmanship for a period of one 1 year from the original date of purchase in accordance with the warranty regulations described below If the product shows any defects within the specified warranty period that are not excluded from this warranty as described under 5 BEHRINGER shall at its discretion either replace or repair the product using suitable new or reconditioned parts In the case that other parts are used which constitute an improvement BEHRINGER may at its discretion charge the customer for the additional cost of these parts 2 If the warranty claim proves to be justified the product will be returned to the user freight prepaid 3 Warranty claims other than those indicated above are expressly excluded 4 RETURN AUTHORIZATION NUMBER 1 To obtain warranty service
34. t occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures A Reorient or relocate the receiving antenna A Increase the separation between the equipment and receiver A Connect the equipment into an outlet on a circuit different from that to which the receiver is connected A Consult the dealer or an experienced radio TV technician for help This device complies with Part 15 of the FCC rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Important information Changes or modifications to the equipment not expressly approved by BEHRINGER USA can void the user s authority to use the equipment EUROPOWER PMP1000 PMP3000 PMP5000 17
35. used for a wide variety of applications Indeed this overwhelming power mixer gives you plenty of functionality and a broad range of connection and expansion options Your PMP features our revolutionary COOLAUDIO amplifier technology which reduces the weight and size of the unit considerably and ensures extremely high output power Further advantages are the integrated Voice Canceller that removes vocal passages from playbacks the FBQ function which detects feedback frequencies and the Speaker Processing function for loudspeaker alignment all with a resolution of 24 bits and 40 kHz Plus our tried and tested XENYX Mic Preamps give you crystal clear audio free of noise and distortion when using microphones BEHRINGER is a company with its roots in professional recording studio technology For many years we have been successful in developing products for studio and live use These include microphones and 19 units of all types compressors enhancers noise gates tube processors headphone amplifiers digital effects DI boxes etc monitor and P A speakers and professional live and recording mixers Our entire technical know how has gone into your PMP power mixer 1 1 Before you get started 1 1 1 Shipment Your PMP was carefully packed at the factory and the packaging is designed to protect the unit from rough handling Nevertheless we recommend that you carefully examine the packaging and its contents for any signs of physic
36. vo vo 1 0 vo 10 vo vo 10 A Sak N an Jah G eae re oh a T aye INSERT oe OUT Keyboard BEHRINGER ooo Hun G Headphone amplifier BEHRINGER POWERPLAY PRO XL HA4700 MON 1 2 OUT O Ol BEHRINGER EUROPOWER EP1500 BEHRINGER HPS3000 BEHRINGER BASS V AMP Passive monitors BEHRINGER IEM EUROLIVE F1520 In Ear Monitoring DAT Recorder Electric bass Fig 5 5 Expanded set up This application is an expanded set up based on the standard set up as shown in fig 5 4 and provides additional connection options Again this is just an example which can be expanded in various ways 5 WIRING EXAMPLES 13 EUROPOWER PMP1000 PMP3000 PMP5000 6 SPECIFICATIONS PMP1000 PMP5000 MICROPHONEINPUTS OC OOSOSOSOSOSOSOSC SCSOSOSCSCSCN NNN Meen omz 0k O OOOO MONO LINE INPUTS S S STEREO LINE INPUTS J EQUALIZER NN _ Low CD TAPE INPUT O O O O OOO O RCA PRE AMP OUTPUTS O SS S MAN o STEREO OUTPUTS OOOO SSS Te pp imTrscomestors unbalaneed i mpedanee roxis0Q unbalaneed Max outputlevel 4 RCA RCA MAIN MIX SYSTEM DATA OOO S Noise LOUDSPEAKER OUTPUTS OY Load mpedanee OOO O O OO O O O SS 14 6 SPECIFICATIONS EUROPOWER PMP1000 PMP3000 PMP5000 Dr mn Signal run time uneina tne O
Download Pdf Manuals
Related Search