Avaya 4606 IP Phone User Manual
Contents
1. m Mute Each of the above features is described in detail in this section Conference The Conference feature allows you to conference up to the maximum number of parties set by your System Administrator Adding another party to a call 1 Dial the first party then press C amp D The current call is placed on hold and you hear a dial tone 2 Dial the number of the next party and wait for an answer 3 Press O again to add the new party to the call 4 Repeat Steps 1 3 for each party you want to conference in to the call Issue 1 July 2001 4 1 Adding a held call to the current call 1 Press O The current line and the held line lights flutter 2 Press the line button of the held call 3 Press CD again All parties are now connected Dropping the last person added to the conference call Press the Line Feature button your System Administrator has designated as the Drop button The last party connected to the conference call is dropped from the call Hold The Hold feature puts a call on hold until you return to it Placing a call on hold Press The green light next to the held line blinks Returning to the held call Press the line button of the held call The call is restored 4 2 Issue 1 July 2001 Mute Mute During an active call the Mute feature prevents the party with whom you are speaking from hearing you This feature is most commonly used in conjunction wit2. 8 To end programming hang up by pressing or lifting and replacing the handset Programming or re programming a single Abbreviated Dialing button on a Line Feature button using an AD Access Code 5 14 Use this procedure only if your System Administrator has programmed an Abbreviated Dialing Access Code Write down the outside numbers extensions and or feature access codes you want to program Each AD button holds one complete phone number or feature access code Issue 1 Pick up the handset Dial the Abbreviated Dialing Access Code if your System Administrator has programmed one The phone goes off hook and the Speaker indicator lights Press the Line Feature button you want to program for Abbreviated Dialing gt NOTE There is a 10 second time limit between your going off hook and entering the first digit of an AD button and then a 10 second time limit between each digit If you hear an intercept tone while you are programming the button you have exceeded the time limit and must begin again Dial the outside number extension or feature Access Code you want to store An automatic dialing number or code can be from 1 16 digits 24 digits are allowed if the number is associated with an AD list see your System Administrator for information When programming an outside number be sure to include the trunk code for example a 9 if applicable Press the key to save the number A confirmation t
3. Pickup and Directed Call Pickup 5 7 Answering a call placed to someone in your pickup group when your phone is idle 5 7 Picking up a call for someone in your office using Directed Call Pickup 5 7 Consult 5 7 a Directory 5 8 Using the Directory feature 5 8 Calling the person whose name is displayed 5 8 a Drop a Person from a Conference Call 5 8 a Exclusion 5 9 a Group Paging 5 9 a Hands Free Answer on Intercom 5 9 a Headset On Off 5 9 Inspect 5 9 Using the Inspect feature 5 9 m Internal Auto Answer Hands Free Answer 5 10 Answering internal calls automatically 5 10 Canceling Internal Auto Answer 5 10 a Leave Word Calling 5 10 Leaving a message after dialing an extension in response to a busy or coverage tone no answer or Hold status 5 11 Leaving a message without ringing an extension 5 11 Canceling a Leave Word Calling message 5 11 a Pause During Abbreviated Dialing 5 11 Priority Calling 5 12 Placing a priority call 5 12 Changing a regular call into a priority call when you hear a call waiting ringback tone 5 12 Issue 1 July 2001 vii Contents a Program Abbreviated Dialing 5 13 Programming or re programming a single Abbreviated Dialing button ona Line Feature button using the Program feature 5 13 Programming or re programming a single Abbreviated Dialing button ona Line Feature button using an AD Access Code 5 14 a Release 5 15 a Ringer Off 5 15 Turning the ringer off 5 15 Turning the ringer back on 5 15 a Sen
4. not correct the problem 1 Unplug the phone and plug it back in The phone connection is re established 2 If power cycling does not correct the problem your System Administrator can perform a more severe power cycle routine by unplugging both the phone and the Ethernet cables Ay WARNING Because the type of power cycle mentioned in Step 2 involves reprogramming certain values it should only be performed by your Telephone System Administrator Issue 1 July 2001 9 5 9 6 Issue 1 July 2001
5. 4 1 Adding another party to a call 4 1 Adding a held call to the current call 4 2 Dropping the last person added to the conference call 4 2 Hold 4 2 Placing a call on hold 4 2 Returning to the held call 4 2 a Mute 4 3 Preventing the other person on the line from hearing you 4 3 a Redial 4 3 Redialing the last number called 4 3 a Speakerphone 4 3 Placing a call without lifting the handset or using the Speakerphone with any feature 4 4 Changing from the speakerphone to the handset 4 4 Turning the speaker on during a call 4 4 Turning the speaker off during a call 4 4 Ending a call while the speaker is active 4 4 Transfer 4 5 Sending a call to another telephone 4 5 SSE ay 5 IP Telephone Features 5 1 m Introduction 5 1 a Accessing IP Telephone Features 5 1 Feature List 5 2 a Abbreviated Dialing AD 5 3 Placing an Abbreviated Dialing call 5 3 Account 5 3 Automatic Callback 5 4 Automatically placing another call to an extension that was busy or did not answer or in response to a returned call waiting ringback tone 5 4 Canceling Automatic Callback 5 4 vi Issue 1 July 2001 Contents a Automatic Intercom 5 4 a Button View 5 5 Viewing the feature programmed ona Line Feature button 5 5 a Call Display 5 9 a Call Forwarding 5 5 Temporarily sending your calls to another phone 5 5 Canceling Call Forwarding 5 6 a Call Park 5 6 Parking a call at your extension 5 6 Retrieving a parked call from another extension 5 6 a Call
6. 6 Issue 1 July 2001 a IP Telephone Features Introduction This chapter contains procedures for using DEFINITY phone features Depending on how your 4606 IP Telephone was set up by your System Administrator you can access some or all of the features discussed in this chapter using Line Feature buttons or Feature Access Codes We cover feature access methods in the next section Following that section a Feature List provides a reference to the procedures for activating and using features which are then listed in alphabetical order Check with your System Administrator for the configuration of your phone system Accessing IP Telephone Features Your 4606 IP Telephone provides two ways to access IP Telephone features 1 Your System Administrator may have programmed some of your telephone s Line Feature buttons to automatically access a feature when pressed In some cases features activated via Line Feature buttons have a steady green indicator light to signify active status When the feature is deactivated turned off the indicator light goes off gt NOTE Note that because the DEFINITY 4606 IP Telephone has just six line feature buttons button activated features may be limited 2 If you don t have a button administered on your phone for a specific feature you may be able to access a feature by entering a two or three digit Feature Access code using the number pad Note that the procedures in this ch
7. Line Feature buttons have been set up for your phone system contact your System Administrator Be sure that the Line Feature button labels are filled in before starting to use your telephone and that you update them promptly for new customized features Issue 1 July 2001 2 1 IP Telephone Features Available on Programmable Line Feature Buttons Regardless of whether a specific feature is available on a Line Feature button or via an Access Code you can find procedures for all 4606 IP Telephone features in Chapter 5 P Telephone Features 2 2 Issue 1 July 2001 a Using the Display Screen Introduction The DEFINITY 4606 IP Telephone has a 2 line by 16 character display screen area located at the top third of the phone What you see on the display is controlled by the current status of the phone or by selections you make using Line Feature buttons Access Codes or dedicated feature buttons like Redial or Transfer The 4606 IP Telephone s display m Indicates the date and time of day on the top line when the phone is idle Displays call information on both lines such as the extension being dialed or the name and extension of someone calling you a Shows feature related instructions or messages when using certain phone features About the Display Screen The two display lines provide general information time of day feature information instructions and or call information Upper Display Lin
8. ace of the telephone Explains how to program certain Line Feature buttons for additional functionality Describes the display screen area at the top of the phone Describes dedicated Feature buttons such as Conference Hold Redial and Transfer Explains the telephone features accessed using Line Feature buttons or Feature Access Codes Covers how to access messages left on your phone Explains how to test your phone and personalize its ringing pattern Interpreting ringer tones and indicator lights are also covered in this chapter Describes the headsets and handsets that are compatible with your IP Telephone Provides basic Troubleshooting actions if you encounter errors or experience problems Conventions Used Conventions Used This guide uses the following textual symbolic and typographic conventions to help you interpret information Symbolic Conventions gt NOTE This symbol precedes additional information about a topic Typographic Conventions This guide uses the following typographic conventions italics Italic type enclosed within quotation marks indicates a document or section in this document containing additional information about a topic italics Italic type indicates the result of an action you take or a system response in step by step procedures Enter In step by step procedures words shown in bold represent a single telephone button that should be pressed These incl
9. aged party cannot speak to you unless the Answering a Whisper Page call procedure is followed 5 18 Issue 1 July 2001 Whisper Page Answer Whisper Page Answer The Whisper Page Answer feature lets you speak with a person who pages you while you are on a call gt NOTE If you have a headset other than those recommended see Chapter 8 or a base unit adaptor other than the M12LU Modular Base Unit plugged into your 4624 telephone the Whisper Page announcement may be overheard by the other person on the call Answering a Whisper Page call 1 When you hear the Whisper Page beep while on a call press the button your System Administrator has designated for Whisper Page Answer Your current call is placed on hold to allow you to speak with the person who paged you The party on hold cannot hear your conversation 2 When you finish speaking with the person who paged you remove the original call from Hold and resume your conversation Whisper Page Off The Whisper Page Off feature prevents callers from using Whisper Page Activate to page your telephone Blocking Whisper Page on your phone your phone must be programmed for Whisper Page off Press the button your System Administrator has designated as the Whisper Page Off button Other parties can no longer page your phone using the Whisper Page Activate procedure Issue 1 July 2001 5 19 5 20 Issue 1 July 2001 Retrieving Voice Messages Message Retriev
10. al Your message indicator lights when a caller has left you a message Because voice mail systems are administered differently among customers check your office procedures for message retrieval For example some telephone users may be authorized to retrieve messages for other telephones not equipped with a display To retrieve a message by dialing the voice mail system Dial your voice mail system directly using the dial pad or if one was programmed by your System Administrator press the Line Feature button for voice mail Some systems also use softkeys for message retrieval Follow your standard voice mail retrieval procedures Contact your System Administrator if you have questions Issue 1 July 2001 6 1 6 2 Issue 1 July 2001 IP Telephone Management Features Introduction This chapter explains how to interpret both the different ringer tones you hear and the telephone s indicator lights Also covered are testing your telephone to be sure it is operating properly and personalizing your phone s ringing pattern Interpreting Ringer Tones As you become more familiar with your IP Telephone you will recognize the various tones you hear in response to an incoming call or while using the handset The chart below provides an overview of the tones you hear check with your System Administrator to verify if the descriptions are accurate for your system Ringing Tones accompany an incoming call Feedback Tones as
11. apter often provide information about using access codes for applicable features Your System Administrator assigns access codes Issue 1 July 2001 5 1 Whether your DEFINITY IP telephone system uses access codes and or feature buttons be sure to check with your System Administrator to find out your phone system s specific configuration Feature List 5 2 The following DEFINITY Features are described in alphabetic order in this chapter Table 5 1 DEFINITY Features Abbreviated Dialing Account Code Entry Automatic Callback Automatic Intercom Button View Call Display Call Forwarding all calls Call Park Call Pickup Directed Call Pickup Consult Directory Drop Conference Call party Exclusion Group Paging Hands Free Answer Headset On Off Inspect Internal Auto Answer Leave Word Calling Pause Priority Calling Program Abbreviated Dialing Release Ringer Off Self Administration Send All Calls Timer View Stored Number Whisper Page Answer Off For information about additional features that your System Administrator may have programmed on your phone see Chapter 4 Managing Phone Features of the Enterprise Communication Server Administrator s Guide Release 8 4 or later Issue 1 July 2001 Abbreviated Dialing AD Abbreviated Dialing AD The Abbreviated Dialing AD feature lets you access stored numbers for quick and easy dialing The numbers stored can be a complet
12. ass A digital device pur suant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications Opera tion of this equipment in a residential area is likely to cause harm ful interference in which case the user will be required to correct the interference at his own expense Part 15 Class B Statement This equipment has been tested and found to comply with the limits for a Class B digital device pursu ant to Part 15 of the FCC Rules These limits are designed to pro vide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equip ment does cause harmful interference to radio or television recep tion which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient the receiving television or radio antenna where thi
13. button by your System Administrator 1 Press the Line Feature button your System Administrator has programmed for the Directory 2 Use the dial pad to key in the name of the person whose number you want to look up Use this format last name comma use the key first name or initial For example to look up the Tom Smith s name press the following number keys 76484 8 The top display line shows your entry The bottom line displays the results of the directory search If no match is found the message No Match Try Again displays 3 To scroll through the Directory press the button your System Administrator has programmed to represent Next 4 To search for a new directory name repeat the procedure from Step 1 Calling the person whose name is displayed 1 Pick up the handset or leave it on hook to use the speakerphone if you have a Call Disp button 2 With the person s name and extension displayed press the Call Disp Line Feature button or If you do not have a Call Disp button dial the extension using the dial pad Drop a Person from a Conference Call See Conference in Chapter 4 Call Handling Features 5 8 Issue 1 July 2001 Exclusion Exclusion The Exclusion feature allows multi appearance users to prevent other multi appearance users having the same extension from bridging on to an existing call Group Paging The Group Page feature allows users make announcements to gro
14. communication DEFINITY 4606 IP Telephone Release 1 User s Guide 555 233 775 Issue 1 Comcode 700206444 July 2001 Copyright 2001 Avaya Inc All Rights Reserved Notice Every effort was made to ensure that the information in this book was complete and accurate at the time of printing However information is subject to change Avaya Web Page The World Wide Web home page for Avaya is http www avaya com Preventing Toll Fraud Toll fraud is the unauthorized use of your telecommunications system by an unauthorized party for example a person who is not a corporate employee agent subcontractor or working on your company s behalf Be aware that there may be a risk of toll fraud associated with your system and that if toll fraud occurs it can result in substantial additional charges for your telecommunica tions services Avaya Fraud Intervention If you suspect you are being victimized by toll fraud and you need technical support or assistance call the appropriate Avaya National Customer Care Center telephone number Users of the MERLIN PARTNER and System 25 products should call 1 800 628 2888 Users of the System 75 System 85 DEFINITY Generic 1 2 and 3 and DEFINITY ECS products should call 1 800 643 2353 Providing Telecommunications Security Telecommunications security of voice data and or video commu nications is the prevention of any type of intrusion to that is either unauthor
15. d All Calls 5 16 Sending all calls except priority calls immediately to a coverage extension 5 16 Canceling send all calls 5 16 Stored Number View 5 17 Viewing either the last number dialed or a number stored on an AD button 5 17 Timer 5 17 Viewing elapsed time hours minutes seconds 5 17 a Whisper Page Activate 5 18 Making an important announcement such as an incoming call to an extension with a call in progress 5 18 a Whisper Page Answer 5 19 Answering a Whisper Page call 5 19 a Whisper Page Off 5 19 Blocking Whisper Page on your phone your phone must be programmed for Whisper Page off 5 19 ee 6 Retrieving Voice Messages 6 1 Message Retrieval 6 1 To retrieve a message by dialing the voice mail system 6 1 viii Issue 1 July 2001 Contents 7 IP Telephone Management Features 7 1 m Introduction 7 1 a Interpreting Ringer Tones 7 1 a Personalizing Your Telephone s Ringing Pattern 7 3 Selecting a personalized ringing pattern 7 3 a Interpreting Indicator Lights 7 3 Testing Your Phone 7 4 Testing the telephone s lights and display 7 4 8 Using a Headset or Specialized Handset 8 1 a Introduction 8 1 a P Telephone Compatible Headsets 8 1 Operating a Headset 8 2 a IP Telephone Compatible Specialized Handsets 8 2 es 9 Troubleshooting 9 1 a Introduction 9 1 Basic Troubleshooting 9 1 a Resetting and Power Cycling the IP Telephone 9 4 Resetting your phone 9 4 Power cycling the phone 9 5 Issue 1 Ju
16. display screen shows the volume leval Changing from the speakerphone to the handset Pick up the handset and talk The Speaker Mute indicator above goes off Turning the speaker on during a call Press C The Speaker Mute indicator above lights Both the speaker and handset are now operational Turning the speaker off during a call Lift the handset at any time The speaker and the corresponding indicator light turn off voice control reverts to the handset Ending a call while the speaker is active Press C The speaker and the corresponding indicator light turn off and the call terminates 4 4 Issue 1 July 2001 Transfer Transfer The Transfer feature lets you transfer a call from your telephone to another extension or outside number Sending a call to another telephone 1 With the call active or with only one held call and no active calls press D The call is placed on hold and its associated indicator light blinks you hear a dial tone and the next available line activates 2 Dial the number to which you want to transfer the call 3 Remain on the line and announce the call if the line is busy or if no one answers return to the held call by pressing the line button on which it is being held Press D again The call is sent to the extension or number you dialed A two second display message indicates the transfer is complete Hang up your handset Issue 1 July 2001 4 5 4
17. e The Time and Date appear on the upper display line when the phone is idle Time and date are set at the switch so if there is an error contact your Telephone System Administrator When plugging in your 4606 IP Telephone for the first time or after a power outage it may take several minutes for the time and date to appear on the display screen Issue 1 July 2001 3 1 Lower Display Line Line Feature Button Information Line Feature button information identifies the line being used Each of the six Line Feature buttons is given an alphabetic designation of a through c left column and d through f right column When the display shows as it represents call information for the first Line Feature button the next button down would show as b and so on Line Feature buttons are also called call appearance buttons Call Information Call information such as the extension being dialed or the name and extension of the person you are calling displays When someone on another extension calls you the display shows the caller s name Outside calls show either the telephone number the words OUTSIDE CALL or a trunk identifier 3 2 Issue 1 July 2001 a Call Handling Features Introduction Call handling features are those you would use while a call is in progress or while making a call They are those features which have a dedicated phone button such as Conference Hold Redial Speaker Transfer
18. e While the phone is ringing pressing the Line Feature button your System Administrator has designated as the Go to Cover button Changing a regular call into a priority call when you hear a call waiting ringback tone 5 12 Issue 1 If you use an access code for priority calling you cannot use an access code after dialing an extension to change a regular call into a priority call If you have a Line Feature button programmed for priority calling stay on the line when you hear the ringback tone indicating the phone is in use and follow the steps above for placing a priority call If you still receive a call waiting ringback tone hang up and place the priority call again in a few minutes July 2001 Program Abbreviated Dialing Program Abbreviated Dialing To be programmable for abbreviated dialing a Line Feature button must be administered for the Abbreviated Dialing feature Note that two separate procedures follow for programming Abbreviated Dialing numbers one for programming Line Feature buttons for abbreviated dialing using the Program feature and one for programming Line Feature buttons for abbreviated dialing using an AD Access Code Programming or re programming a single Abbreviated Dialing button on a Line Feature button using the Program feature Use this procedure only if your System Administrator has programmed a Line Feature button for the Prog Program feature gt NOTE If you make a mistake wh
19. e or partial telephone number a trunk code to access an outside line an extension or a feature Access Code You can also set up a Personal Abbreviated Dialing list to allow you to access frequently dialed numbers using short access codes To be programmable for abbreviated dialing a Line Feature button must be administered for the Abbreviated Dialing feature check with your System Administrator to see if AD is available on your phone then see the Program Abbreviated Dialing feature later in this chapter Also if your telephone s speaker has been disabled lift the handset or use the headset to go off hook before using AD Placing an Abbreviated Dialing call Press the Line Feature button programmed to dial the number or extension you want to call Your call is dialed automatically Account The Account feature allows users to enter Call Detail Recording CDR account codes CDR account codes allow your phone system to associate and track calls according to a particular project or account number Issue 1 July 2001 5 3 Automatic Callback The Automatic Callback feature sends your phone a priority ring indicating the previously busy or unanswered extension you dialed is now available Note that if you initiate call forwarding after activating Automatic Callback returned calls callbacks are not forwarded and ring at your phone Automatically placing another call to an extension that was busy or did not answe
20. erage extension Your Telephone System Administrator must provide a coverage path before you can use this feature If your System Administrator has programmed one of the Line Feature buttons to represent Send All Calls with the phone on hook press that button to initiate coverage or With the phone on hook dial the Send All Calls Access Code You may hear a ring ping half ring tone as each call is forwarded Canceling send all calls 5 16 Issue 1 If your System Administrator has programmed one of the Line Feature buttons to represent Send All Calls with the phone on hook press that button again to cancel coverage or With the phone off hook dial the Send All Calls Cancel Access Code A confirmation tone indicates coverage cancellation July 2001 Stored Number View Stored Number View The Stored Number feature lets you display The numbers stored in Abbreviated Dialing AD locations The number you last dialed Viewing either the last number dialed or a number stored on an AD button 1 Timer If one has been programmed by your System Administrator press the View Line Feature button To view the last number dialed press or To view the number stored on an Abbreviated Dialing button press the applicable AD Line Feature button The associated telephone number displays To return to call handling mode press Exit or to see another feature number repeat this procedure fr
21. h the Speakerphone but can be used to hold an off line conversation at any time during a call Preventing the other person on the line from hearing you 1 Press Ck The other party cannot hear you The indicator light above blinks when Mute is active 2 To reinstate two way conversation press Ck again Redial The Redial or Last Number Dialed feature automatically initiates dialing of the most recent extension or outside number dialed Redialing the last number called Press Ci The last number dialed is automatically redialed Speakerphone A two way built in Speakerphone lets you place and answer calls without lifting the handset Your telephone may be set for the two way Speakerphone or for the one way listen only Speaker Check with your System Administrator to see for which feature your telephone is set gt NOTE It is also possible to disable the Speakerphone feature If your Speakerphone does not operate as indicated contact your System Administrator to be sure your telephone s Speakerphone is enabled Issue 1 July 2001 4 3 Placing a call without lifting the handset or using the Speakerphone with any feature 1 Press C The Speaker Mute indicator above lights and voice control is handled by the speaker 2 Place or answer the call or access the selected feature 3 Adjust the speaker volume if needed by pressing until you reach the desired volume level As you press the
22. ile programming you CANNOT move back a space to erase it Instead press the key or go on hook to erase the entry and start over 1 Write down the outside numbers extensions and or Feature Access codes you want to program Each AD button holds one complete phone number an inside extension or a Feature Access code 2 To enter programming mode press the Line Feature button to which your System Administrator has assigned the Program Abbreviated Dialing feature The phone goes off hook the Speaker indicator lights and the message Press button to program displays 3 Press the pre administered Line Feature button you want to program for Abbreviated Dialing The message Enter number displays 4 Enter the outside number extension or Feature Access Code you want to store An automatic dialing number or code can be from 1 16 digits 24 digits are allowed if the number is associated with an AD list see your System Administrator for information When programming an outside number be sure to include the trunk code for example a 9 if applicable 5 Press the button to save the number or code A three beep confirmation tone indicates the AD number has been stored and the message Number saved displays for one second 6 Record the number code or other identification on the label next to the AD button 7 Repeat Steps 1 through 6 to program additional AD numbers on Line Feature buttons Issue 1 July 2001 5 13
23. ized or malicious access to or use of your com pany s telecommunications equipment by some party Your company s telecommunications equipment includes both this Avaya product and any other voice data video equipment that could be accessed via this Avaya product i e networked equip ment An outside party is anyone who is not a corporate employee agent subcontractor or working on your company s behalf Whereas a malicious party is anyone including someone who may be otherwise authorized who accesses your telecommunica tions equipment with either malicious or mischievous intent Such intrusions may be either to through synchronous time mul tiplexed and or circuit based or asynchronous character mes sage or packet based equipment or interfaces for reasons of e Utilization of capabilities special to the accessed equipment Theft such as of intellectual property financial assets or toll facility access Eavesdropping privacy invasions to humans e Mischief troubling but apparently innocuous tampering e Harm such as harmful tampering data loss or alteration regardless of motive or intent Be aware that there may be a risk of unauthorized intrusions asso ciated with your system and or its networked equipment Also realize that if such an intrusion should occur it could result in a variety of losses to your company including but not limited to human data privacy intellectual p
24. ll Forward Cancel Access Code with the phone off hook The Line indicator light goes off and you hear a confirmation tone your calls will now ring at your phone Call Park The Call Park feature lets you place a call on hold at your telephone for retrieval at any extension Parking a call at your extension If your System Administrator has programmed one of the Line Feature buttons to represent Call Park press that button to initiate Call Park The call is parked at your extension Retrieving a parked call from another extension 1 With the handset off hook dial the Answer Back Access Code 2 Dial the extension where you parked the call usually your own extension If an intercept tone sounds the parked call has been disconnected or retrieved by someone else 5 6 Issue 1 July 2001 Call Pickup and Directed Call Pickup Call Pickup and Directed Call Pickup The Call Pickup feature lets you answer a call at your telephone for another extension in your call pickup group Directed call pickup if available lets you pick up a call for a specific extension even if that extension is not part of your pickup group Because these features may operate differently among customers check your office procedures on picking up calls before performing the procedures below Answering a call placed to someone in your pickup group when your phone is idle If your System Administrator has programmed one of the Line Feature buttons
25. ly 2001 ix Contents x Issue 1 July 2001 a About This Document Purpose The DEFINITY 4606 IP Telephone User s Guide describes the 4606 IP Telephone s operation and functionality Intended Audience This document is intended for telephone users who have a 4606 IP Telephone at their desks It is not intended to be a technical reference guide for System Administrators or phone technicians Issue Date This document was issued for the first time in July 2001 IP Telephone user documentation has been available online at the Avaya support site http support avaya com since October 2000 How to Use This Document This Guide is organized to help you find topics in a logical manner Read it from start to finish to get a thorough understanding of how to use your 4606 IP Telephone or review the Table of Contents to locate information specific to a task or function you want to perform Issue 1 July 2001 xi About This Document Document Organization xii This guide contains the following chapters Chapter 1 4606 IP Telephone Description Chapter 2 Using Programmable Buttons Chapter 3 Using the Display Screen Chapter 4 Call Handling Features Chapter 5 IP Telephone Features Chapter 6 Message Retrieval Chapter 7 IP Telephone Management Features Chapter 8 Using a Headset or Specialized Handset Chapter 9 Troubleshooting Issue 1 July 2001 Describes each element on the f
26. ne to be sure it is properly connected Perform the Test procedure with the telephone idle press and hold D the line feature indicators should light and the display should show all shaded blocks Release D to end the test If the above suggested solutions do not resolve the problem reset or power cycle the phone Most messages involve server phone interaction If you cannot resolve the problem based on the message received contact your Telephone System Administrator for resolution Make sure both the handset and line cords into the phone are securely connected Note that there may be a slight operational delay if you unplug and reconnect the phone If you have a 4612 or 4624 IP Telephone check to be sure the phone is powered press Menu then Exit if nothing appears on the display check your power source If you have a 4612 or 4624 IP Telephone check to be sure your phone is communicating with the switch press Menu then any of the softkey features e g Timer If the selected feature activates the switch IP phone connection is working Reset or power cycle the phone See your Telephone System Administrator if the above steps do not produce the desired result Basic Troubleshooting Echo noise or static when using a headset handset operation works properly Phone does not ring Speakerphone does not operate A feature does not work as indicated in the User Guide All other IP Phone problem
27. nistrator has programmed one of the Line Feature buttons to represent Leave Word Calling press that button to initiate leave word calling The Speaker indicator light activates Dial the extension The Message Indicator light at the extension called goes on Hang up Canceling a Leave Word Calling message You cannot cancel a LWC message left for an AUDIX subscriber 1 If your System Administrator has programmed one of the Line Feature buttons to represent Cancel Leave Word Calling press that button The phone can be either on or off hook Dial the extension at which you left the message You hear a confirmation tone Hang up Pause During Abbreviated Dialing The Pause feature allows a pause to be programmed into an Abbreviated Dialing entry when setting up an abbreviated dialing number or list Issue 1 July 2001 5 11 Priority Calling The Priority Calling feature lets you place an internal call with a distinctive ring usually a 3 burst ring to indicate your call needs immediate attention Placing a priority call q If your System Administrator has programmed one of the Line Feature buttons to represent Priority Calling press that button or Dial the Priority Calling Access Code Dial the extension and wait for the person to answer The extension called receives three ring tones and the message Priority displays If your call is not answered you can redirect it to a person on coverag
28. om Step 2 The Timer display feature lets you measure elapsed time Viewing elapsed time hours minutes seconds 1 Press the Line Feature button your System Administrator has programmed for the Timer feature The elapsed time displays To stop the Timer and clear the display press the button your System Administrator has programmed for the Timer feature again The time elapsed since initiating the Timer displays for about three seconds then disappears Issue 1 July 2001 5 17 Whisper Page Activate The Whisper Page feature lets you make an announcement to a person at another extension who is currently on a call only the person being paged hears the announcement gt NOTE If you have a headset other than those recommended see Chapter 8 or a base unit adaptor other than the M12LU Modular Base Unit plugged into your 4624 telephone the Whisper Page announcement may be overheard by the other person on the call Making an important announcement such as an incoming call to an extension with a call in progress 1 If your System Administrator has programmed one of the Line Feature buttons to represent Whisper Page Activate press that button or Dial the Whisper Page Activate Access Code You hear a dial tone 2 Dial the number of the person you want to page Both parties on the other call hear a beep You can now speak to the party you paged without the other person on the call hearing you The p
29. one indicates the AD number has been stored Record the number code or other identification on the label next to the AD button Repeat Steps 4 through 6 to program additional AD buttons To end programming hang up by pressing or lifting the handset July 2001 Release Release The Release feature allows an agent on an ACD Automated Call Dialing call to be released from that call This feature is used in conjunction with other ACD features Ringer Off The Ringer Off feature stops your phone from ringing Use this feature when you don t want to be disturbed When your ringer is set to off the Line indicator lights and the display alerts you to incoming calls Your phone also gives one short ring burst to indicate an incoming call Turning the ringer off If your System Administrator has programmed one of the Line Feature buttons to represent ringer off press that button or Dial the Ringer Off Access Code Turning the ringer back on If your System Administrator has programmed one of the Line Feature buttons to represent Ringer Off press that button again to turn the ringer back on or Dial the Ringer Off Access Code again Issue 1 July 2001 5 15 Send All Calls The Send All Calls feature lets you temporarily send your calls to the extension of a person designated by the System Administrator to answer them when you cannot Sending all calls except priority calls immediately to a cov
30. r or in response to a returned call waiting ringback tone T 3 During a call attempt press the button your System Administrator has designated for Automatic Callback Three tones indicate Automatic Callback is active Hang up You hear a priority ring when both your phone and the number you called are available The display shows the message Callback When you hear the priority ring lift the handset Your call proceeds as originally dialed gt NOTE Automatic Callback cancels automatically after 30 minutes Canceling Automatic Callback With the handset on hook press the button your System Administrator has designated for Automatic Callback again One tone indicates automatic callback is canceled this feature automatically cancels after 30 minutes Automatic Intercom 5 4 The Automatic Intercom feature places a call to a specific phone associated with this button The recipient of the call receives a unique alerting ring and the indicator light associated with the intercom button flashes Issue 1 July 2001 Button View Button View The Button View feature lets you display the name of the feature that has been programmed on any of your telephone s Line Feature call appearance buttons Viewing the feature programmed on a Line Feature button Press the button your System Administrator has programmed to represent Button View Press the Line Feature button for which you want
31. r Noise Canceling Encore Ultra VT Encore Ultra Noise Canceling Encore Ultra Il Encore Ultra Il Noise Canceling Mirage Ultra Mirage Ultra Noise Canceling Starset Supra Starter Starter Special VT Starter Special Noise Canceling Supra Starter Noise Canceling Supra Ultra Supra Ultra Noise Canceling Supra Ultra II Twin Top Supra Ultra Il Noise Canceling Tristar Ultra Tristar Ultra Noise Canceling Issue 1 July 2001 8 1 Operating a Headset Headset operation must be administered by your System Administrator and requires either an M12LU Modular Base Unit PEC 3124 022 or a 3124 HIC Attenuation headset adapter Cord PEC 3124 HIC For the latest list of compatible headsets and adapters or for ordering information access Products and Services at www avayadirect com IP Telephone Compatible Specialized Handsets The IP Phone s handset interface labeled HAC on the underside of the phone is compatible with the following handsets ABIC the handset provided with your phone AB5C a AB6C a AB8C Specialized handsets are available for noisy environments hearing impaired users and other special purposes These handsets are labeled either as K type or AJ type handsets For the latest list of special purpose handsets and ordering information access Products and Services at www avayadirect com 8 2 Issue 1 July 2001 a Troubleshooting Introduction The DEFINITY 4600 Series IP Telephones a
32. re relatively trouble free The Basic Troubleshooting chart provides the most common problems an end user might encounter The remaining pages in this chapter provide procedures for resetting or power cycling your phone when Basic Troubleshooting does not resolve the problem For all other IP Telephone questions or problems contact your Telephone System Administrator Basic Troubleshooting Problem Symptom Suggested Solution Phone does not activate after Unless your System Administrator has connecting it the first time already initialized your telephone you may experience a delay of several minutes before it becomes operational Upon plug in your telephone immediately begins downloading its operational software its IP address and any special features programmed by your System Administrator from the server to which it is connected Report any delay of more than 8 10 minutes to your System Administrator Phone does not activate after Allow afew minutes for re initialization a power interruption after unplugging powering down the phone server problems or other power interruption causes Issue 1 July 2001 9 1 9 2 Issue 1 Characters do not appear on the Display screen Display shows an error informational message No dial tone July 2001 See Phone does not activate after connecting it the first time above Check the power source to be sure your telephone is receiving power Check all lines into the pho
33. received e A reorder tone is received Industry Canada IC Interference Information This digital apparatus does not exceed the Class A limits for radio noise emissions set out in the radio interference regula tions of Industry Canada Le Pr sent Appareil Nom rique n met pas de bruits radio lectriques d passant les limites applicables aux appar eils num riques de la class A pr scrites dans le reglement sur le brouillage radio lectrique dict par le Industrie Canada Trademarks All trademarks identified by and SM are registered trademarks trademarks or service marks respectively of Avaya Inc All other trademarks are the properties of their respective owners Ordering Information Call Avaya Publications Center US Voice 1 800 457 1235 US Fax 1 800 457 1764 non US Voice 1 207 866 6701 non US Fax 1 207 626 7269 Write Globalware Solutions 200 Ward Hill Avenue Haverhill MA 01835 USA You can be placed on a standing order list for this and other documents you may need For more information on standing orders or to be put on a list to receive future issues of this document contact the Avaya Publications Center Obtaining Products To learn more about Avaya products and to order products contact Avaya Direct the direct market organization of Avaya Business Communications Systems Access their web site at www avayadirect com Or call the following numbers customers 1 800 451 2100 account execu
34. roperty material assets finan cial resources labor costs and or legal costs Your Responsibility for Your Company s Telecommunications Security The final responsibility for securing both this system and its net worked equipment rests with you an Avaya customer s system administrator your telecommunications peers and your managers Base the fulfillment of your responsibility on acquired knowledge and resources from a variety of sources including but not limited to e Installation documents e System administration documents e Security documents e Hardware software based security tools Shared information between you and your peers e Telecommunications security experts To prevent intrusions to your telecommunications equipment you and your peers should carefully program and configure your e Avaya provided telecommunications systems and their interfaces e Avaya provided software applications as well as their underlying hardware software platforms and interfaces e Any other equipment networked to your Avaya products Avaya does not warrant that this product or any of its networked equipment is either immune from or will prevent either unautho rized or malicious intrusions Avaya will not be responsible for any charges losses or damages that result from such intrusions Federal Communications Commission Statement Part 15 Class A Statement This equipment has been tested and found to comply with the limits for a Cl
35. s Check the headset connection If the connection is secure verify that you are using an approved headset base unit and or adapter as described in the list of approved Avaya Communication compatible Headsets in Chapter 8 of this guide If you have a 4612 or 4624 IP Telephone use the Menu to access the RngOf Ringer Off feature if a carat downward triangle appears above that feature your phone is set to not ring To correct press the softkey below RngOf when the carat does not display your ringer is active If Ringer Off is programmed on a Line Feature button that button s indicator light will appear as steady green reactivate the ringer by pressing that Line Feature button again Set your ringer volume to a higher level using the Up Down Volume keys From another phone place a call to your extension to test the above suggested solutions Ask your System Administrator if your Speakerphone has been disabled Verify the procedure and retry For certain features you must lift the handset first or place the phone off hook See your Telephone System Administrator if the above action does not produce the desired result your telephone system may have been specially programmed for certain features applicable only to your installation Contact your Telephone System Administrator Issue 1 July 2001 9 3 Resetting and Power Cycling the IP Telephone Reset your IP Telephone when other Trouble
36. s may be done safely To the extent possible relocate the receiver with respect to the telephone equipment e Where the telephone equipment requires ac power plug the telephone into a different ac outlet so that the telephone equipment and receiver are on different branch circuits Part 15 Personal Computer Statement This equipment has been certified to comply with the limits for a Class B computing device pursuant to Subpart J of Part 15 of FCC Rules Only peripherals computing input output devices terminals printers etc certified to comply with the Class B limits may be attached to this computer Operation with non certified peripherals is likely to result in interference to radio and television reception Part 68 Network Registration Number This equipment is registered with the FCC in accordance with Part 68 of the FCC Rules Part 68 Answer Supervision Signaling Allowing this equipment to be operated in a manner that does not provide proper answer supervision signaling is in violation of Part 68 Rules This equipment returns answer supervision signals to the public switched network when e Answered by the called station e Answered by the attendant Routed to a recorded announcement that can be administered by the CPE user This equipment returns answer supervision signals on all DID calls forwarded back to the public switched telephone network Permissible exceptions are e A call is unanswered e A busy tone is
37. shooting suggestions do not correct the problem Use a Power Cycle with the approval of your System Administrator only when a reset does not resolve the problem Resetting your phone This basic reset procedure should resolve most problems 1 Press 2 Using the dial pad press the following keys in sequence 73738 The display shows the message Reset values no yes 3 Choose one of the following If you want to Reset the phone without resetting any assigned values Reset the phone and any previously assigned programmed values Use this option only if your phone has programmed static values Then Press asterisk A confirmation tone sounds and the display prompts Restart phone no yes Press the pound key The display shows the message Resetting values while your IP Telephone resets its programmed values such as the IP address to its default values and re establishes the connection to the server The display then prompts Restart phone no yes 4 Press to restart the phone or to terminate the restart and restore the phone to its previous state gt NOTE Any reset restart of your phone may take a few minutes Issue 1 July 2001 Resetting and Power Cycling the IP Telephone Power cycling the phone Use the power cycle with your System Administrator s approval only if the basic or programmed reset procedure cannot be performed or does
38. shown on the next page are those which you hear through the handset receiver or the speaker Ringing Incoming Tones Meaning 1 Ring Call from another extension 2 Rings Call from outside or the System Administrator 3 Rings Priority call from another extension or from an Automatic Callback call you placed Half Ring ring ping A call is being redirected from your phone to another because Send All Calls or Call Forwarding All Calls is active Issue 1 July 2001 7 1 Feedback Handset Tones Call Waiting Ringback Tone _ Confirmation Coverage Intercept Time out Recall Dial Reorder Ringback 7 2 Issue 1 July 2001 Meaning Low pitched rapid tone repeated 60 times per minute signifying the number dialed is in use A ringback tone with lower pitched signal at the end indicates the extension called is busy and the called party has been given a call waiting tone If you hear this tone you may want to activate Automatic Callback Three short tone bursts indicates a feature activation or cancellation has been accepted One short tone burst indicates your call will be sent to another extension to be answered by a covering user Continuous tone indicating dialing can begin Alternating high and low tone indicating either a dialing error denial of a requested service or failure
39. swer press that button to initiate this feature or Dial the Internal Auto Answer Access Code A three tone warble sounds when your phone goes off hook on each internal call The Speaker indicator lights 2 Use the Speakerphone to proceed with the call Canceling Internal Auto Answer If your System Administrator has programmed one of the Line Feature buttons to represent Internal Auto Answer Hands Free Answer press that button to cancel internal auto answer or Dial the Internal Auto Answer Access Code again Control reverts to the handset Leave Word Calling 5 10 The Leave Word Calling LWC feature lets you leave a standard message for a person at another extension LWC allows the called party to retrieve a short standard message your name extension date and time called and number of times you called from your message service AUDIX other voice mail system or a covering user Issue 1 July 2001 Pause During Abbreviated Dialing Leaving a message after dialing an extension in response to a busy or coverage tone no answer or Hold status 1 If your System Administrator has programmed one of the Line Feature buttons to represent Leave Word Calling press that button to initiate leave word calling The Speaker indicator light activates Hang up The Message Indicator light at the extension called goes on Leaving a message without ringing an extension 1 3 If your System Admi
40. ther person from hearing you The LED above the Spkr button flashes when the microphone is muted 10 Volume Control Adjust the speaker handset or ringer volume depending on which item is in use 11 Numeric Dialing Pad Standard 12 button pad for dialing phone numbers 12 Hold Red button used to place a call on hold 1 2 Issue 1 July 2001 Using Programmable Buttons Introduction Your 4606 IP Telephone has six Line Feature buttons some of which are dedicated to incoming and outgoing calls The remaining Line Feature buttons can be programmed by your Telephone System Administrator to provide additional phone functionality Programmable Line Feature Buttons Line buttons available for incoming outgoing calls are usually the first few buttons on the left most button column The Line Feature buttons following your incoming outgoing lines may be reserved for features not available using dedicated buttons like Conference Ck Mute and Speaker Features such as Voice Mail retrieval Directory search Inspect phone features and Program may also be assigned to this group of buttons These features may alternately be available through Feature Access Codes Two suggested features for 4606 IP Telephone users to add are Drop which allows a party to be dropped from a conference call and Normal which clears the display when using certain features like the Directory For information regarding how the
41. time when the Timer feature is active 2 O Conference Set up conference calls with more than one other person With the phone on hook also used to select a personal ringing pattern 3 D Transfer Transfer a call to another phone With the phone on hook also used to test lights and the display screen 4 Redial Redial the last number dialed from the phone 5 Line Feature buttons Several of the six buttons are Line buttons dedicated to incoming and outgoing calls those line buttons are labeled with an extension number The Line Feature buttons not dedicated to incoming or outgoing calls provide access to system features like sending all calls to another phone or speed dialing For your specific configuration see your System Administrator One red and one green light appear next to each button Steady red indicates the line is available Steady green indicates the line or feature is in use other green light indications winking fluttering and flashing are feature specific 6 Mute Speaker Light Lights steadily when the Speakerphone is active Flashes when the handset headset or Speakerphone microphone is muted 7 Speaker Access the built in two way full duplex Speakerphone feature The LED above this button lights when the speakerphone is active 8 Voice Message Light When lit indicates you have a message waiting 9 Mute Turn off the active microphone handset or speaker to prevent the o
42. tives 1 888 778 1880 voice or 1 888 778 1881 fax Warranty Avaya provides a limited warranty on this product Refer to the Limited Use Software License Agreement card pro vided with your package European Union Declaration of Conformity The CE mark affixed to the equipment means that it con forms to the above directives Avaya Business Communica tions Systems declares that equipment specified in this document conforms to the referenced European Union EU Directives and Harmonized Standards listed below EMC Directive 89 336 EEC Low Voltage Directive73 23 EEC Acknowledgment This document was prepared by Avaya University Avaya Denver CO Contents a About This Document xi Purpose xi m Intended Audience xi a Issue Date xi a Howto Use This Document xi Document Organization xii Conventions Used xiii Symbolic Conventions xiii Typographic Conventions xiii a Related Documentation Training xiii es 1 4606 IP Telephone Description 1 1 a Introduction 1 1 The 4606 IP Phone 1 1 ay 2 Using Programmable Buttons 2 1 a Introduction 2 1 a Programmable Line Feature Buttons 2 1 a IP Telephone Features Available on Programmable Line Feature Buttons 2 2 ee 3 Using the Display Screen 3 1 a Introduction 3 1 About the Display Screen 3 1 Upper Display Line 3 1 Lower Display Line Fa Issue 1 July 2001 v Contents 4 Call Handling Features 4 1 m Introduction 4 1 Conference
43. to dial within a preset interval usually 10 seconds after lifting the handset or dialing the previous digit Three shorts tone bursts followed by a steady dial tone to indicate a feature request has been accepted and dialing can start Fast busy tone repeated every half second to indicate all phone trunk lines are busy Low pitched tone repeated 15 times a minute to indicate the number dialed is ringing Personalizing Your Telephone s Ringing Pattern Personalizing Your Telephone s Ringing Pattern The Select Ring feature lets you choose your own personalized ringing pattern from among eight different patterns Selecting a personalized ringing pattern With the phone on hook press CO The current ringing pattern sounds and repeats every three seconds Continue to press and then release O to cycle through each of the eight ring patterns To save a ringing pattern as it plays do not continue to press C You hear the selected ringing pattern two more times after which it is automatically saved A confirmation tone two rising tones sounds and your new ringing pattern is set gt NOTE Going off hook receiving a call or losing power during ring pattern selection interrupts the process and you must start over from Step 1 Interpreting Indicator Lights As you become more familiar with your IP Telephone you will recognize the lights associated with a Line Feature button The chart below provides an o
44. to represent Call Pickup press the Call Pickup Feature button or Dial the Call Pickup Access Code The extension called stops ringing and you are connected to the call for pickup Picking up a call for someone in your office using Directed Call Pickup 1 If your System Administrator has programmed one of the Line Feature buttons to represent Directed Call Pickup press that button or Dial the Directed Call Pickup Access Code 2 Dial the extension for which you want to pick up a call The extension called stops ringing and you are connected to the call for pickup Consult The Consult feature allows a covering user after answering a coverage call to call the principal the party called for private consultation Activating the Consult feature places the caller on hold and establishes a private connection between the principal and the covering user The covering user may then add the caller to the conversation transfer the call to the principal or return to the caller Issue 1 July 2001 5 7 Directory The Directory feature allows you to search a stored list of telephone numbers by keying in the name of the person whose number you want using the dial pad Initially your directory will be set up by your System Administrator to include only those phones that are part of your telephone system Using the Directory feature To fully use the Directory both the Directory and Next should be programmed on a Line Feature
45. to see its assigned function The Line Feature button assignment or telephone number displays To see another feature number repeat this procedure from Step 2 Call Display The Call Display feature initiates a call to the phone extension or number shown on the display screen The number displayed could be from a Leave Word Calling LWC message or a number you retrieved using the directory feature Call Forwarding The Call Forwarding feature lets you redirect all calls to your phone to another extension or an outside number Because this feature may operate differently among customers check your office procedures for call forwarding before performing the procedures below Call forwarding must be disabled to resume call pickup at your phone Temporarily sending your calls to another phone T If your System Administrator has programmed one of the Line Feature buttons to represent Call Forwarding press that button to initiate call forwarding or Dial the Call Forward Access Code with the phone off hook 2 Dial the extension or number to which calls should be sent 3 Hang up When Call Forwarding has been activated the Line indicator light is on and you may hear a brief ring ping tone as each call is forwarded Issue 1 July 2001 5 5 Canceling Call Forwarding 1 If your System Administrator has programmed one of the Line Feature buttons to represent Call Forwarding Cancel press that button or Dial the Ca
46. ude Menu Exit and Related Documentation Training An online interactive IP Telephone User s Guide can be found at www http support avaya com For information related to installing an IP Telephone see the 4600 Series IP Telephone Installation Guide Document Number 555 233 128 Comcode 700197858 For information related to maintaining an IP Telephone System on a Local Area Network see the 4600 Series IP Telephone LAN Administrator s Guide Document Number 555 233 507 Comcode 700197841 Issue 1 July 2001 xiii About This Document xiv Issue 1 July 2001 a 4606 IP Telephone Description Introduction This chapter introduces you to the layout of the 4606 IP Telephone It provides a description for each functional button and other phone characteristics The 4606 IP Phone The 4606 IP telephone is a multi line phone with 6 Line Feature buttons 6 dedicated feature buttons a 2 line by 16 character display area and a full duplex two way speakerphone Issue 1 July 2001 1 1 Match the numbered callouts on the 4606 illustration to the descriptions below 1 Display The display screen has two lines of 16 characters each During phone usage the top line shows the name phone number you are calling or the name phone number of the person calling you while idle it displays the current date and time The second line also displays volume control when a volume arrow is pressed and elapsed
47. ups of phone stations by automatically turning on their speakerphones Hands Free Answer on Intercom See Internal Auto Answer in this chapter Headset On Off The Headset On Off feature allows headset usage to be activated or deactivated using a Line Feature button When this feature is active the green indicator light corresponding to the button administered signifies the headset is off hook when the indicator is not lit it signifies on hook headset status Inspect The Inspect feature provides call related information for an incoming or held call when you are active on another call Using the Inspect feature 1 Press the Line Feature button your System Administrator has programmed to represent this feature 2 Press the Line Feature button of the incoming or held call The display shows the name and or number of the person calling on hold and you remain connected to the active call 3 To answer the incoming or held call put the current call on hold or hang up 4 Press the Line Feature button of the incoming or held call Issue 1 July 2001 5 9 Internal Auto Answer Hands Free Answer The Internal Auto Answer or Hands Free Answer on Intercom feature lets your Speakerphone equipped telephone automatically go off hook to answer internal calls Answering internal calls automatically If your System Administrator has programmed one of the Line Feature buttons to represent Internal Auto An
48. verview of the indicator lights you see check with your System Administrator to verify if the descriptions are accurate for your system Light Meaning Steady Red The line is available Steady Green Indicates the line is in use or the feature programmed for that button is on active Blinking Green Indicates a call is on hold on this line Flashing Green An incoming call is arriving on this line Fluttering Green This line s call was put on hold pending a conference or a transfer Issue 1 July 2001 7 3 Testing Your Phone The Test feature lets you verify that your telephone s lights and display are operating properly Testing the telephone s lights and display With the phone idle press and hold D The Line Feature indicators light and the display lines each show 16 shaded blocks representing the 16 characters available on each line To end the test release GO The lights and display return to normal operation If any indicator light or the display does not respond during the test contact your Telephone System Administrator 7 4 Issue 1 July 2001 a Using a Headset or Specialized Handset Introduction This chapter describes the headsets and specialized handsets that are compatible with your IP telephone How to operate a headset is also covered IP Telephone Compatible Headsets Use any of the following headsets with the 4600 Series IP Telephones Earset Starter Earset Starte
Download Pdf Manuals
Related Search