Audiovox LCM1502TV TV DVD Combo User Manual
Contents
1. LCM1502TV Owner s Manual Audiovox Specialized Applications LLC www asaelectronics com US PATENT D467 234 Important Notice It is unlawful in most jurisdictions for a person to drive a motor vehicle which is equipped with a television viewer or screen that is located in the motor vehicle at any point forward of the back of the driver s seat or that is visible directly or indirectly to the driver while operating the vehicle In the interest of safety the LCM1502TV should never be installed where it will be visible directly or indirectly by the operator of the motor vehicle Please note that the state of Rhode Island forbids the Installation of such a device in a motor vehicle Television Reception This entertainment system is designed primarily for viewing pre recorded movies or playing video games Television reception in a moving vehicle will be limited and in some areas will not be possible due to weak and variable signal strength Television viewing in a stationary vehicle will result in an improvement but may still be marginal due to strength The quality of the picture will not be consistent with home TV reception Reception may be affected by the weather and distance from the TV station A weak signal may cause the picture to roll be snowy or cause some color loss Congratulations on your purchase of the Flexvision LCM1502TV drop down TV Video Monitor The LCM1502TV has been designed to give you a2. SET PICTURE AUTO PROGRAM ANTENNA INPUT V CHIP PROTECT SET PASSWORD OFF 4 Press either CHANNEL up or down to select the function Make sure the highlight bar is SET PICTURE and then press ENTER CHANNEL SELECT VIDEO CLOSED CAPTION CONTRAST BRIGHTNESS V MENL AUTO PROGRAM SHARPNESS TINT ANTENNA INPUT V CHIP PROTECT RESET SET PASSWORD 4 6 Select the item to adjust For example To adjust brightness press CHANNEL up or down buttons to select BRIGHTNESS and press ENTER CHANNEL PICTURE v 4 COLOR CONTRAST ty SHARPNESS RESET 6 Adjust the level Press VOLUME VOLUME 50 BRIGHTNESS H 12 7 To adjust other items repeat all above Notes The menu or display disappears from the screen if you do not press or within a few seconds Whenever a menu or display disappears from the screen the and buttons on the front of the TV become the volume adjustment buttons If you want to adjust the picture only You can use the remote control simply press the PICTURE SELECT Description of adjustment items ltem Adjustment Press VOLUME Down Press VOLUME Up CONTRAST Decrease picture contrast Increase picture contrast for vivid for soft color color BRIGHTNESS Darken the picture Brighten the picture SHARPNESS Decrease picture sharpness Increase picture sharpness TINT Decrease Tint Increase Tint COLOR
3. Use the MENU button to return to the menu on the next level up x7 SETTING THE V CHIP An age limitation can be set to forbid children to see and hear violent scenes or pictures for adults etc The TV VCR responds to TV RATING and MOVIE RATING To use the V CHIP function you must register a password 1 Press MENU This main menu appears MENU MAIN MENU SELECT VIDEO CLOSED CAPTION SET PICTURE AUTO PROGRAM ANTENNA INPUT V CHIP PROTECT SET PASSWORD 2 Press either CHANNEL up or down buttons to select the function Make sure the highlight bar is SET PASSWORD and then press ENTER CHANNEL Zia OLD PASSWORD SELECT VIDEO MAIN MENU SELECT VIDEO CLOSED CAPTION SET PICTURE AUTO PROGRAM ANTENNA INPUT V CHIP PROTECT SET PASSWORD CLOSED CAPTION SET PICTURE AUTO PROGRAM ANTENNA INPUT V CHIP PROTECT OLD PASSWORD 18 3 Enter the OLD password 4 digits using the Direct channel selection buttons 0 9 4 Enter the NEW password 4 digits using the Direct channel selection buttons 0 9 NOTES The initial PASSWORD is 1111 If you forget the password you cannot set the V CHIP To avoid forgetting the password write it down and Keep in a Safe place TO SET THE V CHIP 1 Press MENU The main menu appears ME MAIN MENU SELECT VIDEO CLOSED CAPTION SET PICTURE AUTO PROGRAM ANTENNA INPUT V CHIP PROTECT SET PASSWORD 19 2 Press
4. Verify connections at both ends of source component harness IR sensor inoperative Verify that the batteries in the remote are fresh Verify that the remote eye is not obstructed Verify that the infrared transmitter is affixed over the sensor eye of the component to be controlled Specifications LCD Brightness Operation Temperature Storage Temperature Video Display System Audio Output Current Draw Weight Overall Dimensions 28 450 nits min 20 C 65 C 40 C 80 C NTSC 0 6W Variable 3 2A 6 kgs 15 5 x14 5 x2 5 H x W x D AAUDIOVOX PECIALIZED AAPPLICATIONS L L C www asaelectronics com 10 2002
5. STOP Button Press this button to stop the video tape REPLAY Button Press this button will rewind the video tape and immediately begin playback when the video tape is fully rewind ADJUSTING THE PICTURE When watching TV programs the quality of the picture can be adjusted to suit your taste 1 Press MENU The main menu appears MENU SELECT VIDEO CLOSED CAPTION SET PICTURE AUTO PROGRAM ANTENNA INPUT V CHIP PROTECT SET PASSWORD 2 Press SELECT VIDEO The video source appears Press this button to access the AUDIO VIDEO input jacks _ MAIN MENU SELECT VIDEO CLOSED CAPTION SET PICTURE ENTER AUTO PROGRAM ANTENNA INPUT V CHIP PROTECT SET PASSWORD 10 3 Select CLOSED CAPTION and then press ENTER Closed captioning lets you display the audio portion of a program as text on the TV screen This is useful to the hearing impaired or anyone who wants to watch a program without the sound There are two types of closed captioning available C1 Caption 1 and C2 Caption 2 C1 display the full translation of the primary language in your area C2 may be used as a source for secondary languages simplified English or other translations transmitted in your area Closed captioning is not available on all channels or at all times Only specific programs are encoded with closed captioning information CHANNEL CAPTION ty CAPTION 1 CLOSED CAPTION CAPTION 2
6. 10 12345 6 789 10 POWER VOLUME Up and Down TV AV SENSOR EYE THREE POSITION DOME LIGHT SWITCH SCREEN RELEASE MENU CHANNEL Up and Down ENTER 0 DOME LIGHT a moi FRONT PANEL FEATURES See Figure 1 1 Power Button Bright red when system is ON dim when system is OFF 2 Volume Up Down Controls volume to external Speakers if connected Also used to adjust the picture control setting when contrast bright sharpness color or tint is displayed on the screen 3 TV AV Any video equipment connected to the AUDIO VIDEO inputs can be used with the TV by pressing this button Each time the button is pressed the Audio Video source will change in the following sequence TV AV1 AV2 and AUX 4 Sensor Eye Allows the remote control to operate the LCM1502TV s OSD system On Screen Display volume to Wired Headphone Jacks and optional external speakers and for control of Video Media Player connected through a source component harness Three Position Dome Light Switch e Auto Automatically switched on the dome lights in conjunction with the vehicles interior illumination e Off The Dome lights will not turn on in this position e On Turns on the Dome lights Screen release Slides in the direction of the arrow to release the drop down screen NOTE For safety hand hold the screen before you slides the screen release to drop down screen Menu But
7. 8 press 0 8 To select channels above 100 press the 1 button then the number buttons for the last two digits of the channel For example to select channel 115 press 1 1 5 CHANNEL Up and Down Use these buttons to select pre programmed channels or two select channels up or down also used to select desired function on the menu VOLUME Up and Down Use these buttons to raise or lower the volume level of the Wired Headphones or External Speakers if installed They are also used to make adjustments in the picture select mode NOTE These buttons will not affect the volume of wireless headphones or a wired RF modulator When using these devices the volume must be adjusted with the headphone volume control or with your radio s volume control MENU Button Press the MENU button The MENU display appears Use the Channel up and down buttons to select desired function then press ENTER button to end the choice 6 TV VIDEO Button Press this button to access the AUDIO VIDEO input jacks on the front and rear of the TV As the button is pressed the on screen display will cycle as follows i AV1 9 2 AUX 7 MUTE Button Press this button to turn the TV sound off Press again to restore sound to the previously set level MUTE may also be released by pressing the VOLUME 8 ERASE ADD Button When tuned to a channel press this button to store or erase the channel from memory The stored channel numbers are displa
8. Decrease color intensity Increase color intensity To restore the factory settings Select the item of picture while the main menu is displayed Then select the item of RESET All the picture functions CONTRAST BRIGHTNESS SHARPNESS TINT COLOR will go back to the factory settings 13 8 Press either CHANNEL up or down to select the function Make sure the highlight bar is AUTO PROGRAM and then press ENTER CHANNEL SELECT VIDEO CLOSED CAPTION SET PICTURE AUTO PROGRAM ANTENNA INPUT VCHIP PROTECT SET PASSWORD ERASE CHANNEL AUTO PROGRAM A 9 Press either CHANNEL up or down select the function Make sure the highlight bar is ANTENNA INPUT and then press ENTER CHANNEL CLOSED CAPTION SELECT VIDEO t SET PICTURE AUTO PROGRAM ANTENNA INPUT PATER VCHIP PROTECT SET PASSWORD 14 CABLE TV CATV OPERATION In addition to normal broadcast reception of VHF and UHF channels if you are a cable TV subscriber your new TV is capable of receiving many unscrambled cable channels without the use of a converter box When set to broadcast TV it receives channels 2 69 When set to one of the CATV mode STD it receives channels 1 125 see chart on the following CABLE TV TUNING PROCEDURE 1 Connect the CATV cable directly to the TV antenna terminal Your local cable system operator s converter box should not be required unless certain premium channels are scrambled 2 Select the ap
9. CHIP function is activated only on programs and tapes that the rating signal 3942 7 MOVIE RATINGS CHART MOVIE B LOCKING G ALL ages MP PG Parental guidance MP PG 13 Parental guidance less than 13 years old MP R Under 17 years old Parental guidance suggested MP NC 17 17 years old and above MP X Adult only MP N R Movie has not been rated or ratings do not apply Press VOLUME or to select the contained rating Block or Show 22 OPERATION OVERHEAD DOME LIGHTS A three position slide switch controls the Dome Lights on the LCM1502TV Sliding the switch to the ON position will turn the Dome Lights ON The OFF position will prevent the Dome Lights from turning ON at all times and the auto position will allow the Dome Lights to turn ON and OFF with the vehicle s interior lighting Do not leave the vehicle unattended with the Dome Lights switch in the ON position as this could result in a discharged battery Dome Lig Ht Dome Light Switch 23 REMOTE INFRARED SENSOR REPEATER The LCM1502TV incorporates a Infrared Sensor which relays the signals from the Remote Control to allow the LCM1502TV to be controlled simply by pointing it s Remote Control at the remote sensor This provides control of auxiliary equipment such as an Flexvision VCP or DVD Player The Remote Infrared Sensor can relay signals from most manufacturers Remote Control to its respective component connected to the Vide
10. E TERMINAL DOME LIGHT SEE OWNER MANUAL DOME LIGHT SEE OWNER MANUAL 412V POWER 18 2 PIN CONNECTOR PIN 1 WIFE INSERTION VIEW Negative Dome Light Switching Positive Dome Light Switching White Entry switch Negative White Entry Switch Positive Black Constant 12VDC Dome circuit Black Chassis Ground Red Chassis Ground Red Constant 12VDC Dome Circuit 27 Troubleshootin PROBLEM SOLUTION Poor TV Reception Poor radio reception FM modulator installed No power to LCD Power but no video or sound Perform auto programming of the tuner Verify antenna condition NOTE Due to the nature of TV signals vehicle motion direction the vehicle is facing distance from the transmitter nearby surroundings and weather may adversely affect TV reception These conditions may result in the following picture roll snowy picture or momentary loss of color Please refer to page 2 for more information on TV reception Check the condition of the vehicle s radio antenna Verify that the antenna is fully raised If a wired RF modulator has been installed verify that it s switch is turned to the off position Verify 12VDC on red wire at power harness going to the video pod Verify ground connection
11. eadphones for more information 25 WIRED FM MODULATOR P N FMT100 Your video system may be equipped with an optional RF modulator that allows you to listen to the LCM1502TV s audio signal by tuning your vehicle s radio to the selected frequency 88 7 or 89 1 check with your installer and tuning on the remote mounted RF modulator switch In most cases this toggle switch will be located underneath the drivers side of the dash check with your installer for the exact location Whenever the RF Modulator is ON broadcast radio reception will be poor Turning the remote mounted toggle switch OFF will allow for normal radio reception TYPICAL SYSTEM CONNECTIONS DD ami a Z gu 26 18 PIN MAIN HARNESS DETAIL PIN NO FUNCTION AWG TERMINATION LINE AUDIO GROUND RED WHITE RCA CONNECTOR AUDIO GROUND SHIELD 5 PIN CONNECTOR PIN 2 POWER GROUND S PIN CONNECTOR PIN 5 LINE AUDIO OUT RED RCACONNECTOR VIDEO OUT YELLOW RCA CONNECTOR SPEAKER OUT GROUND MALE SPADE TERMINAL LINE AUDIO L OUT 2 WHITE RCA CONNECTOR DOME LIGHT SEE OWNER MANUAL POWER GROUND 18 2 PIN CONNECTOR PIN 2 AUDIO R OUT 2 5 PIN CONNECTOR PIN 3 AUDIO L OUT 24 5 PIN CONNECTOR PIN 1 12V POWER 2 5 PIN CONNECTOR PIN 4 VIDEO GROUND 18 YELLOW RCA CONNECTOR SPEAKER OUT LEFT 18 MALE SPADE TERMINAL SPEAKER OUT RIGHT 18 MALE SPAD
12. either CHANNEL up or down buttons to select the function Make sure the highlight bar is V CHIP PROTECT and then press ENTER MAIN MENU SELECT VIDEO CLOSED PASSWORD SET PICTURE AUTO PROGRAM V CHIP ANTENNA INPUT TV CHANNEL BLOCKING V CHIP PROTECT MOVIE BLOCKING SET PASSWORD 3 Enter the password 4 digits using the Direct channel Selection buttons 0 9 appears in stead of the number Note The initial password is 1111 4 In the V CHIP PROTECT menu Press either CHANNEL up or down buttons to select the function 5 Press either VOLUME or VOLUME to select the desired setting 6 TV RATINGS CHART TV CHANNEL BLOCKING TVY None TV Y ALL children TV Y7 None TV Y7 7 years old and above TVG None TV G General Audience TV PG None TV PG Parental guidance TV 14 None TV 14 14 years old and above TV 17 years old and above 20 TVY None All TVY7 All FV TVG None All TVPG None Al D L S V DL DS DV LS LV SV DLS DLV IDSV LSV IDLSV TV 14 None All D L S DS LS LV SV DLSDLV IDSV LSV DLSV TV MANone All L S V 1 LV SV LSV When you select TV Y7 TV PG TV 14 or TV MA press either CHANNEL up or down buttons to select the contained rating V FV VIOLENCE S SITUATIONS L LANGUAGE D DIALOG Press VOLUME or to select contained rating NOTE The V
13. nd your family many years of video entertainment in the mobile environment Please read the directions that follow to familiarize yourself with the product and to ensure that you obtain the best results from your equipment NOTE Installation options vary See the individual Owner s Manuals for each component in your system to obtain a full understanding of each components operation SAFETY PRECAUTION For safety reasons when changing Video Media it is recommended that the vehicle is not in motion and that you do not allow children to unfasten seat belts to change Video Media or make adjustments to the system System adjustments can be accomplished using the Remote Control while seat belts remain fastened Enjoy your Flexvision entertainment system but remember safety of all passengers remains the number one priority FEATURES 15 TFT Thin Film Transistor Active Matrix LCD Liquid Crystal Display Monitor OSD On Screen Display For Control Of Picture Quality And Functions Full Function Remote Control 3 AN inputs with TV Tuner as a fourth source IR repeater for control of Flexvision DVD VCP through a source component harness Direct single cable connection to Flexvision DVD VCP products Variable Audio output for wired headphone external speaker connections Back Lit Controls For Low Light Operation 49MHz RF Transmitter Dual Dome Lights A V outputs for connection to a second monitor FRONT PANEL FEATURE Figure 1
14. o 1 and 2 inputs In this case you must use the Remote Control supplied with the other manufacturers component Remote Infrared Sensor VIDEO OUTPUT The LCM1502TV provides a video output for an optional Video monitor s This output will provide a video signal that duplicates the signal displayed by the LCM1502TV to an additional Monitor or Video display Please see your installer for more information AUXILIARY A V STEREO INPUTS JACK The LCM1502TV is equipped with an auxiliary A V input connector The inputs are provided to facilitate the connection of Audio Video equipment such as a camcorder or video game system To play a source with these inputs an RCA patch cord is required to connect the Audio Video signals to their respective jacks Mono audio sources will require the use of an RCA Y cable P N 0892165 to connect to both right and left inputs 24 AUXIN L WHT AUXIN R RED AUXIN V YLW T OPTIONAL ACCESSORIES WIRELESS HEADPHONES The LCM1502TV includes a 49MHz RFTransmitter for use with Flexvision Wireless Headphones P N WHPRF01 Turning the Headphone switch ON will activate the internal RF Receiver the volume can then be adjusted using the controls on each headset Use the adjustment knob on the headset to fine tune the Headphones to the proper frequency Any number of wireless headphones can be used Consult the documentation accompanying the Flexvision Wireless H
15. propriate CATV setting with the TV CATV button on the remote control 15 3 You can now select CATV programs by using the CHANNEL up and down buttons or the number buttons on the remote control The chart below lists the total channel and cable count Channels Off Air Cable Low VHF Channel 01 1 VHF Channels 2 13 12 12 UHF Channels 14 69 56 Low Midband 5 A 1 Channels 95 99 5 Midband Channels 14 22 or A 1 Superband Channels 23 36 or J W 14 Ultraband 37 94 and 100 125 or w 29 w 48 84 Total 68 125 16 PARENTAL CONTROL SETTINGS This item helps parents set the standard for the programs their children are going to watch Mo oc e With the TV on press the MENU button until special menu will appear Use the Channel up and down buttons to select the V Chip Control item Use the VOL Up buttons to enter into V Chip Control Settings After using the number buttons 0 9 to enter your password the V Chip Control menu will be displayed If this is the first time you are using your V Chip Control menu your default password is 1111 Select the V Chip Control feature Use the VOL Up buttons to toggle on or off Use the Channel Up and down buttons to select the V Chip Control settings you wish to adjust Descriptions of the V Chip Control settings are on the next page Use the VOL Up buttons to adjust the V Chip Control setting selected
16. ton Gives you access to the OSD Main Menu Channel Up Down Changes the TV channel ENTER Button Use this button to end the choice on the menu 10 Dome Lights Provide additional illumination REMOTE CONTROL OPERATION o BATTERY INSTALLATION Before attempting to operate the Remote Control install the batteries as described below 1 Turn the Remote Control face down Press down on the ridged area of the battery cover and slide it off 2 Install Two AAA batteries as shown Make sure that proper polarity or is observed 3 Slide the cover back until it clicks into position The Remote Control will operate the LCM1502TV Flexvision Televisions and Video Media Players It is not a universal remote control and will not control equipment from other manufacturers If a universal Remote Control is used with the LCM1502TV choose the remote control encoding scheme Flexvision Televisions when programming the remote ORS ooo REMOTE CONTROL OPERATION 1 TV Controls 1 TV POWER Press this button to turn on the set Press the button again to turn the set off Direct Access 0 9 1 Number Buttons Use these buttons to select a channel The channel number chosen will be displayed on the screen for about four seconds To select channels 0 99 press two number buttons For example to select channel
17. y in GREEN on the screen and the no stored channel numbers are in RED 9 AUTO PROGRAM Button Select the regular channel broadcast TV or CABLE TV for AUTO PROGRAM All the channel numbers for TV or CABLE TV will be scanned The broadcasting signals will be detected and automatically stored 10 ENTER Button Use this button to end the choice on the menu 11 PICTURE SELECT Button Each time this button is pressed the on screen picture adjustment display cycles through adjustment screens as follows BRIGHTNESS CONTRAST COLOR SHARPNESS HELL 2 VCR Controls 12 13 14 15 16 17 VCP POWER Button This button is used to turn the unit on and off REW REWIND Button If this button is pushed while the tape is stopped the tape will rewind If this button is pushed while the tape is playing the VCP will go into rewind search mode For more information on search feature of the VCP consult VCP owner s manual PLAY Button Press this button to activate play mode while a tape is loaded into the VCP This button may also be used to dis engage search and pause modes For more information consult the VCP owner s manual F FWD FAST FORWARD Button If this button is pushed while the tape is stopped tape will fast forward If this button is pushed while the tape is playing the VCP will go into fast forward search mode For more information on search feature of the VCP consult the VCP owner s manual
Download Pdf Manuals
Related Search