AOC V27M Computer Monitor User Manual
Contents
1. HDMI HD Multimedia Interface ee a RE HDMI 15 Source Interface PC Signal and PC Audio Input Connect the PC to the PC input connector on the back of the monitor with a VGA cable Also connect the audio cable between PC Audio Input of the monitor and the PC audio connector Earphone Jack Earphones can be connected to the Earphone jack D SUB vO e a 16 Using the Menu 1 2 3 Press the Menu button to display the menu Select the menu option to be adjusted using the Up or Down key Enter the submenu by pressing the VOL Up key Enable or adjust the function selected by pressing the VOL Up and Down key The selected option will be highlighted Press the Menu button again to exit the menu Source Menu Press Source button to enter the Source menu including PC HDMI Video S video Component HDMI i fy V S Video YPbPr d Move mala Enter 17 Using the Menu Video Settings Brightness Contrast Color Temp Warm DCR Pict ho ure Mode User Reset Brightness Contrast Color Saturation Sharpness Color Temperature DNR Image Mode DCR Reset 18 Enter This adjusts the brightness of the screen backlight The adjustment range is between 0 and 100 This adjusts the screen contrast The adjustment range is between 0 and 100 This adjusts the screen color intensity The adjustment range is between 0 and 100 This control is not available in P2. 20 Coc e ee ee ea cee ee eee ee et 26 China RoHS Regulation Marking Heouremente 2 Important safety notes Read these notes before operating the device a EE 10 11 12 13 14 15 Read these notes Follow these notes Heed all warnings Operate as per instructions Do not use this apparatus near water for example near the bathtub kitchen sink washbasin washing machine in a humid basement or near the swimming pool If the unit is accidentally splashed please disconnect the power plug immediately and contact the authorized distributor Only use a dry cloth for cleaning Always unplug the monitor power cable before cleaning Do not allow any hard object to touch the screen as this may cause permanent damage Do not obstruct the vents and install the device in accordance with the manufacturer s instructions Do not install the device near heat sources such as electric heaters radiators ovens or any other heat source including amplifiers Always use a polarized plug or a plug with a ground connection Polarized plugs have one wide and one narrow flat pin Grounded plugs have two flat pins and one round grounding pin The wider flat pin and round grounding pin are designed for safety If the provided plug does not fit your outlet socket consult an electrician for a replacement of the obsolete socket Protect the power cord from being trodden upon or pinched particularly near the plug and the po
3. BB minated Cr diphenyl ethers PBDE ss RY e CRR Display CRR Display LCD Display Lamp e Plasma Plasma Display Circuit Board Assembly Power Adapter Power Adapter The circuit board assembly includes the printed circuit board and its components such as resistors capacitors integrated circuits connectors etc O Indicates that the toxic and hazardous substances contained in all of the homogeneous material for this part is below the Limit Requirements Standard for the Toxic and Hazardous Substances in Electronic Information Products X Indicates that this toxic and hazardous substance contained in at least one of the homogeneous materials used for this part is above the Limit Requirements Standard for the Toxic and Hazardous Substances in Electronic Information Products however the part marked with X complies with the EU RoHS Regulations exempted This mark indicates the period 10 Years that the toxic and hazardous substances or elements contained in this electronic information product will not 10 J leak or change under normal operating conditions No serious damage to persons property or environment will occur when this product is used 27
4. C and Component modes This adjusts the sharpness of the picture The adjustment range is between 0 and 100 This option provides four color temperature settings Normal Warm Cold and User Setting This control is not available in PC mode This option provides four settings Soft Standard Vivid and User Setting Enable disable Dynamic Contrast Ratio Restore the video settings to factory mode Using the Menu Audio Settings applicable to all modes ae ape Fa e is ees etna eee i i ts GIE EE Soun d Mode Standard GEES Treble Reset Enter Sound Quality Switches between the five audio modes Bass This is used to adjust the bass strength Treble This is used to adjust the treble strength Equalizer The sound adjustment range is 0 to 60 During adjustment from 30 to 0 the sound from the right channel will gradually decrease until it disappears During adjustment from 30 to 60 the sound from the left channel will gradually decrease until it disappears Reset Restore the audio settings to factory mode 19 Using the Menu Function settings Language English Sleep Time OTI OSD Position 4 IOSD Transp Power Saver Power On Recall Reset Enter Menu Language This sets the language used for the OSD There are 24 Aspect Ratio Sleep Timer OSD Position available languages including English and Simplified Chinese 4 3 16 9 Movie This control is not available in PC mode Panor
5. V2 m ZC Multimedia Function Display Operating Instructions Thank you for choosing an AOC LCD Monitor It is recommended that you read the contents of this manual carefully before installing and turning on the monitor Please keep this manual for future reference Note Our products are under continuous development and are subject to change without notice The monitor may not be an exact match to the illustrations in this manual But the monitor is the standard Operating Instructions Content Important Safely NOLES E 5 Read these notes before operating the device 5 Connection and preparation of Uemontor eee 7 leg EE T Installation of the base 8 Disassembly of the base 8 Stand the monitor on a stable surface cccceceeeeee es 9 Installing the monitor on the wall 10 POWER COMMECUOM DEE 10 Turning the LCD Monitor On or Om 11 Control Panel and Interface 12 no 9 Sl OFS Te ae en Ma oe enn en rT een ne 12 SOUNCC LCT ie 13 Video SVideo leie EEN 14 Auxiliary Component Input 15 IVI lui EE 15 PC Signal and PC Audio Input 16 Al MONE WACK EE 16 USNO ING MENU seais en EEE Ea aR 17 Source Men E EE 17 Video Settings ccc ceccceccceeceeeeeeeeeeeseeseeeeeeeseeseeeaeeeaes 18 Audio Settings applicable to all modesl 19 FUNCION SOUNO S E 20 Product SDCCIIIGANOMS E 22 SUDPOMEd RESOUNON WEE 23 Troubleshooting c cece cece eee eeceeceeeseeceeeeeeseeeeeeseeeeeeaeeseeeeeeees
6. ama This control is not available in PC mode This sets the interval before your monitor will automatically enter standby mode This changes the OSD menu display position with 9 options available OSD Transparency This adjusts the transparency of the OSD menu The Display Time Power Saving adjustment range is between 0 and 100 This adjusts the display time in seconds of the OSD menu The adjustment range is between 0 and 60 Enable disable Power Saving Power On Recall Enable disable Power On Recall Reset 20 Restores function settings to the factory default Tips Do not use any hard object to wipe the screen as this may cause permanent damage Unplug the monitor before cleaning the screen Clean the screen and casing with a clean soft cloth to remove dust Do not use liquid cleaning agents or aerosols Do not allow liquids to enter the LCD display as this may cause damage to its internal parts Mobile phones Keep all mobile phones away from the monitor The radio signals from the phone may cause image deformation and distort the sound The monitor may behave abnormally or it may even be damaged Waste disposal instructions We attach great importance to environmental protection This monitor contains recoverable and reusable materials There are professional companies that dismantle discarded electronic equipment to recover recyclable material This minimizes waste and also the amount of material tha
7. e Source Interface A device with multiple sources can be connected to your monitor The figure below shows how to connect Tip If you want to wall mount your monitor all cables must be connected to the monitor connectors first Whenever an external device is connected to your monitor please make sure the monitor is turned off When connecting an external device connect the cable to the connector with the same color PC Signal and Component Input PC Audio Input HDMI e 4 Fo Pr p ue OOOOO oe goe 000 4 SERVICE SS viceo _ Earphone Jack Video S Video Input 13 Source Interface Video S Video Input Connect the Video or S Video cable to the DVD player CD player Video Recorder or Camcorder etc Audio Input Connect the audio sources e g computer DVD player CD player Video Recorder or Camcorder to the Audio Input connector Tip Audio is shared between S Video and Video Ss bei 8 pt E S VIDEO J SVIDEO q 14 Source Interface Auxiliary Component Input Connect the auxiliary source audio and video e g computer DVD player CD player Video Recorder or Camcorder to the Component Input connector Y Pb Pr Component Video Input L R Y Ph Pr N fam N a a gt L RI NT J ed A HDMI Input Connect the HDMI source e g computer DVD player CD player Video Recorder or Camcorder to the HDMI Input connector HDMI
8. e abnormal or has changed significantly E The monitor has been dropped or its casing has been damaged Dimensions stability All monitors must conform to recommended international standards in terms of casing design dimensions and stability Do not push the monitor on the front of the casing or at the top it may overturn and be damaged Do not put electronic devices or toys on the casing these may fall and be damaged or cause personal injury Foreign articles and liquid Do not allow foreign articles or liquid to enter the casing through the ventilation slots Connection and preparation of the monitor Parts list AOC V27m Bracket Base Screws f Cleaning cloth Warranty Card Warranty card VGA cable W Operating Instructions CD ROM HDMI cable Audio cable Screws Quick Installation Guide Connection and preparation of the monitor Installation of the base Take the monitor and the base out of the carton and assemble them as shown in the figure below 1 Place the monitor face down on a soft cloth or pad on the table Tighten the screws in the base to secure the base and bracket 2 Inset the base into the hole on the bottom of the monitor Disassembly of the base Inset a screw driver into the base mounting hole press it downwards and pull out the base Connection and preparation of the monitor Stand the monitor on a stable surface 1 Choose a position for the
9. e to 60HZz 25 Glossary Audio video input These connectors RCA type plug are located on the back of the monitor It is specially designed to be used with a video recorder or other accessories to receive higher image resolution and sound S Video input Connects directly to high resolution video sources such as a Super VHS recorder disc player etc and provides better image resolution and definition Component signal input Allows the monitor to connect directly to high resolution video sources such as the component signal input of a DVD player and digital television It provides better image resolution and definition Menu This is the function control list displayed on the monitor and used for adjustments Sleep timer The monitor can be set to turn off after a fixed amount of time using this feature 26 China RoHS Regulation Marking Requirements According to China s Management Methods for Controlling Pollution by Electronic Information Products or commonly referred to as China RoHS the following lists the names and content of the toxic or hazardous substances or elements that may be contained in this product Products applicable to this table Display LCD or CRT flat panel TV LCD and Plasma and monitor Toxic and Hazardous Substances or Elements Toxic and Hazardous Substances or Elements Lead Mercury Cadmium Hexavalent Polybro minated Polybro Part Name Pb Hg Cd Chromium biphenyls P
10. int where it exits the apparatus Only use accessories specified by the manufacturer Use only with a cart stand tripod bracket or table specified by the manufacturer or supplied with the apparatus When a cart is used use caution when moving the cart apparatus combination to avoid the device being tipped Over es bh Apm 83125A lt a Use the correct power source as indicated on the label Consult the distributor or the local power company if you are not sure about the power provided to your home Unplug the monitor during thunderstorms or if it will not be used for a long time 16 17 18 19 20 All servicing must be carried out by professional service personnel Servicing is required if the device does not work normally or has been damaged in some way For example if the power cord has been damaged if liquid has been spilled on it it has been exposed to rain or moisture or it has been dropped The product may contain lead or mercury Environmental factors should be taken into account when you dispose these materials For disposal or recycling information contact the local authority or Electronic Industries Alliance www eiae org Damage requiring servicing Consult a professional service technician under any of the following circumstances A The power cord or plug has been damaged B Foreign objects or liquid have entered the monitor C The monitor has been rained on D Operation seems to b
11. monitor that has good ventilation and make sure the ventilation holes on the cover are clear of obstruction 2 Ensure the LCD monitor has 15cm of clearance on all sides to provide proper ventilation 3 Do not place the LCD monitor near a radiator or other powered devices 4 Do not use open flames such as candles near the monitor to prevent accidents 5 Keep the monitor away from high temperatures direct sunlight rain or moisture 6 To prevent the monitor from tipping over secure it to the table as shown below Connection and preparation of the monitor Installing the monitor on the wall The monitor conforms to the wall mounted VESA standard Please refer to the instructions for product specifications and details To ensure your own safety and that of the monitor use only the specified wall mounting bracket Please note that wall mounting must be done by a professional technician When the monitor is mounted on a wall it must be possible to access the connectors at the back At least 6cm of clearance will be needed between the monitor and the wall to ensure that there is enough space to insert the connection cables It is important that air should flow freely through the ventilation slots wherever the monitor is installed Do not install the monitor in a confined space Power connection Insert one end of the power cord into the Power Input socket on the back and plug the other end into a 220V po
12. s and solutions to your problems Symptoms Items to be inspected and measures to be taken Check whether the power cord of the monitor is plugged into the outlet Unplug the monitor from the mains wait for 60 seconds plug it into the outlet again and turn it on There is no need to take any action because the LCD panel A static colored spot is manufactured using high technology to display the refined appears on your TV picture details Sometimes an inactive pixel can be screen displayed as a static red blue green or black spot on the screen This will not affect monitor performance Adjust the contrast and brightness settings Normal image but no Turn up the volume sound Check that a proper source is selected Normal sound but Adjust the contrast saturation and brightness settings poor color When an external device such as S VHS video recorder or Poor image quality camcorder is connected G image quality may be poor Turn off other external devices for the time being Horizontai dotted ling This may be caused by electronic interference such as a hair dryer or nearby fluorescent tube Turn off the device Check that the VGA connection is secure VGA mode does not Check that a proper signal source is selected work Check if you have selected the correct resolution for the PC Check the video card settings of the PC In VGA mode black bars appear on the top and bottom of the VGA display Set the PC refresh rat
13. t needs final disposal The lamp tubes of this product contain mercury Please dispose of this product in accordance with local laws and regulations 21 Product Specifications Panel Size Diagonal 686mm 27 Native Resolution 1920 x 1080 Viewing Angle Horizontal 170 Vertical 160 Typ Available Voltage Range Power Consumption Load Power Consumption Idle lt 1W Dimension W x H x D 680 x 546 x 262 Wall mount Accessories Not included 100 x 100mm Wall mount Dimension M4 x 4 pcs screws Environmental Requirements Operating Temperature UC 35 C Humidity 20 80 Storage Temperature 20 C 50 C Humidity 10 90 22 Supported Resolution Default PC Mode Standard H Frequency kHz V Frequency kHz VGA 23 Supported Resolution Standard WSXGA WSXGA HD 24 H Frequency kHz V Frequency kHz 1680X1050 60Hz CVT16 10 65 290 59 954 1680X1050 60Hz RB CVT16 10 64 674 59 883 1920x1080 60Hz 67 500 60 000 480P 60Hz for SDTV Digital 31 469 59 94 only 5 6P 50Hz for SDTV Digital 31 250 50 000 only o for HDTV Digital 45 000 60 000 720P 50Hz for HDTV Digital 37 500 50 000 only 1080i 60Hz for HDTV Digital 33 750 60 000 only 1080i 50Hz for HDTV Digital 28 125 50 000 only 1080P 60Hz for HDTV Digital 67 500 60 000 only os for HDTV Digital 56 250 50 000 Troubleshooting Before calling our Customer Service check this troubleshooting list to understand the symptom
14. wer socket The monitor consumes a small amount of power in standby mode But it should be unplugged from the power socket if it is not to be used for some time 10 Turning the LCD Monitor On or Off 1 To turn on Connect the AC power to the monitor Press the power button on the control panel and the indicator light will turn blue After a few seconds the monitor will be operating normally e Press the power button on the control panel to turn the monitor off 2 To turn off 3 Indicator status 1 In normal operating mode the monitor indicator light will be blue 2 In standby mode the light will be orange 3 In power off mode the monitor indicator light will flash blue three times and then go off 11 Control Panel and Interface Side panel Signal Source Menu A V Volume 12 Volume Volume Menu el zZ W Source SOURCE Press button to enter the interface of signal source selections and press again to select the source needed when menu is unavailable on display Once menu occur this key is used for confirmation purpose and select to confirm target you needed Press to enter or exit the menu When the menu appears on the screen use these two buttons to select the desired option With the menu displayed on the screen press these two buttons to select the desired option When no OSD menu is displayed on the screen the controls will adjust sound volum
Download Pdf Manuals
Related Search