AOC A17UX231 Flat Panel Television User Manual
Contents
1. 18 Regulatory Notices 18 PRODUCT SPECIFICATION 19 BEFORE CALLING SERVICE 21 Glossary 22 Thank you very much for choosing the LCD TV We recommend that you take a few minutes to read carefully through this manual before installing and switching on the TV Please keep this manual in a safe place for your future reference FOR YOUR SAFETY Before operating the TV please read this manual thoroughly This manual should be retained for future reference IMPORTANT SAFETY INSTRUCTIONS Read before operating equipment AOLO Ol Sa 10 11 12 13 14 15 Read these instructions Keep these instructions Heed all warnings Follow all instructions Do not use this apparatus near water Clean only with a dry cloth Do not block any of the ventilation openings Install in accordance with the manufacturers instructions Do not install near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and third grounding prong The wide blade or third prong is provided for your safety When the provided plug does not fit into y2. Ghost or double This may be caused by obstruction to the image antenna due to high rise buildings or hills Using a highly directional antenna may inprove the picture No power Check that the TV s AC power cord is plugged into the mains socket Unplug the TV wait for 60 seconds Then re insert plug into the mains socket and turn on the TV again No picture Check antenna connections at the rear of the TV to see if it is properly connected to the TV possible broadcast station trouble Try another channel Adjust the contrast and brightness settings Check the V Chip control Some V Chip modes could block the screen Good picture but no Increase the VOLUME sound Check that the TV is not muted press the button on the remote control Good sound but poor Adjust the contrast color and brightness color settings Adjust TV Mode AIR or CATV HRC IRC check that is ok or not Poor picture Sometimes poor picture quality occurs when having activated an S VHS camera or camcorder connected and having connected another peripheral at the same time In this case switch off one of the other peripherals Snowy picture and Check the antenna connection noise Horizontal dotted line This may be caused by electrical interference e g hairdryer nearby neon lights etc Turn off the equipment Television not Check whether the batteries are working responding to remote Replace if necessary
3. broadcast standard A monaural soundtrack included within the recorded or video signal usually containing a second language translation for the displayed program Sleep Timer Function with which you can set a time period after which the TV should turn itself off 24
4. control Clean the remote control sensor lens on the TV You can still use the buttons at the front of your TV Select the TV mode to be sure your remote 22 control is in the TV mode 23 GLOSSARY Audio Video Inputs Located on the rear and the front of the receiver these connectors RCA phono type plug are used for the input of audio and video signals Designed for use with VCRs or other accessories in order to receive higher picture resolution and offer sound connection options S Video Input Allows direct connection of high resolution video sources such as a Super VHS videocassette recorder Laser Disc player etc Provides improved picture resolution sharpness and Clarity component Input Allows direct connector of high resolution vedio sources such as DVD player digital TV etc provides improved picture resolution sharpness and Clarity Audio output Provide sound output it can be connected external speaker and enhance the sound quality Menu An on screen listing of feature controls shown on the TV screen that are made available for user adjustments Multichannel Television sound MTS The broadcast standard that allows for stereo sound to be transmitted with the TV picture RF Radio Frequency or modulated signal design used as the carrier for television broadcasts Second Audio Program SAP Another or additional audio channel provided for in the Multichannel Television Sound MTS
5. AOC A17UX231 EYES VALUE User s Manual LCD TV 41T17TV673 5A6275 USER S MANUAL TABLE OF CONTENTS INSTALLATION n n nnnonnnnnnnennnnnnnnnnnnnnnnnnnnnnnnnmnnnnn 1 For Your Safety 1 IMPORTANT SAFETY INSTRUCTIONS 3 PREPARATION n a n nnna nn nnn nn nnnnnnnnmnnnnnnnnnnnnnnnnnnanannnannnnn 4 OPERATING INSTRUCTIONS 6 Use of the remote control 6 To use the I CIS 7 Main Menu 7 CONNECT PERIPHERAL EQUIPMENT 14 Front Panel Control Knobs 14 Preparation 15 Video recorder 16 Camera camcorder Video Game set 16 DVD player 17 Digital Set TOP DOxX 17 Headphone 17 TIPS
6. ault functions are the same except those in menus set by the user which can reset all settings to default value in all menus SOUND Setup 1 Volume is adjusted from 0 to 100 2 Bass and Treble are adjusted from 0 to 100 You can adjust picture Volume Bass and Treble to the levels you prefer 3 The adjustment range of balance is from O to 100 0 to 50 is used to adjust the volume of right speaker from low to loud 50 to 100 is used to adjust the volume of left speaker from loud to low 4 The Mute is ON or OFF and if the Mute is ON there are no sound output OSD Setup L English Set OSD language Adjust the horizontal position of the OSD Adjust the vertical position of the OSD Adjust the OSD time out OSD Background Adjustment Show the resolution H V frequency and input port of current input timing Do not execute reset return to main menu Note This item is available only in PC mode QOnkwns gt 10 TV Setup _ Kw AIR CATV for different TV input solution RF and cable Auto searching is used for searching all TV program channels After finishing search and exiting the machine will save the program automatically you can also press menu to break the searching but only the searched programs are saved when the machine exits searching Add Erase is for add or delete the current channel for memorizes Current Program is display the current channel number Sl
7. can select warm or cool 14 CONNECT PERIPHERAL EQUIPMENT FRONT PANEL CONTROL KNOBS Power Key Press to turn on or off the TV MENU Key Press to show the OSD menu and exit OSD menu at the TV Down Up Key Press to perform select function and channel Key Press to confirm your function selection and adjustment Source Key Press to select your input source There is a wide range of video and audio equipment that can be connected to your TV The following connection diagrams show you how to connect them 15 PREPARATION Remove the back plate at the back of the TV as shown on the illustration opposite Lay the LCD TV with the screen down on a table as it will be easier to connect your peripheral equipment Please take precaution not to damage the screen Lr mh saaaa0000 ci y 0000886000 S RF TV port Earphone output port Right channel input port Left channel input port AV video port PC signal port 12V power input port S VIDEO video port INN ONOaAABRWDND 16 VIDEO RECORDER How to connect 1 Connect the supplied antenna cable to the RF IN port of your VCR 2 Connect another RF cable from the output RF of your VCR to the input of your TV Better quality when playing from your VCR can be obtained if you also connect the Video Audio LEFT AND right only for stereo equipment cables to the VIDEO AUDIO L and R inputs AV If your VCR
8. colors 16 2 million Lamp Type Life 50000 hr LCD Panel Color Temperature Cool Warm TV Standard NTSC M TV Function Sound systems MTS SAP Colour systems DPF function Supported by memory Optional card Not supported Wireless earphone Optional FM transmission frequency Not supported RCA x 1 AV S VIDEO Audio L R x 1 Share S Video x 1 20 Signal Input PnP compatibility DDC 2B Analog FH 31 5KHz to 80KHz FV 56Hz to75Hz Recommended Analog 1280 x 1024 60Hz Input Audio AV Share Speaker built in Two 2 watt speakers Input frequency Audio Output L R Headphone Mini jack for stereo 3 5 English French Spanish Portuguese Table Stand Included Wall Mount VESA 100 x 100 mm Power Supply AC100V 240V 50 60Hz Power Consumption lt 50W Panel Tilt Forwards Backwards 5 15 operating 0 C 40 C storage Environment 25 C 60 C operating 10 85 Dimension W xH x D withstand 368 4 x 378 9 x 196 6 mm Weight net Kg w o Accessories _ 4 2 Kg Remote Controller Batteries AAAx2 AC Power Cord adapter User s Manual Signal Cable Audio Cable 21 Before Calling Service Please make these simple checks before calling service These tips may save you time and money since charges for receiver installation and adjustments of customer controls are not covered under your warranty
9. eep Timer It is for set a time period after which the TV should switch itself to standby The counter runs from Disabled 30 gt 60 gt 90 gt 120 minutes The setting will be removed when using reset CLOSED CAPTION It s allows you to read the dialogue of television programs on the TV screen Designed to help the earing impaired this feature uses on screen text boxes to show dialogue and conversations wile the TV program is in progress Captions will appear on the screen only during captioned broadcasts Remark the captions do not always use correct spelling and grammar Not all TV programs and product commercials are made for broadcast with Closed Caption information included Refer to your area s TV program listings for the TV channels and times of closed Caption shows The captioned programs are usually noted in the TV listings with serviceMarks such as CO Caption Mode CC1 CC4 Dialogue and descriptions for the action on the captioned TV program shows on screen 11 Text Mode TT1 TT4 Often used for channel guide schedules bulletin board information for Closed Caption programs news weather information or stock marker reports Not all Closed Caption modes are necessarily being use by a TV channel during the transmission of a Closed Caption program V CHIP Setup Select V Chip on OSD then enter 4 digits of pin number Initial pin number is 0000 If you enter an incorrect pin number Erro
10. er grounding of the mats and supporting structure grounding of the lead in wire to an antenna discharge unit size of grounding connectors location of antenna discharge unit connection to grounding electrodes and requirements for the grounding electrode See Figure below ANTENNA GROUND CLAMP GROUND CLAMPS GROUNDING CONDUCTORS POWER SERVICE GROUNDING ELECTRODE SYSTEM EXAMPLE OF ANTENNA GROUNDING AS PER NATIONAL ELECTRICAL CODE Note to the CATV system installer This reminder is provided to call the CATV system installer s attention to Article 820 40 of the NEC that provides guidelines for proper grounding and in particular specifies that the cable ground shall be connected to the grounding system of the building as close to the point of cable entry as practical 22 Objects and Liquid Entry Care should be taken so that objects do not fall and liquids are not spilled into the enclosure through openings PREPARATION Please make sure to connect the power plug to the wall outlet socket after connecting the TV to the adapter 1 Place the TV on a solid surface Acad a es KS Ensure that the TV is placed in a position to allow free flow of air Do not cover the ventilation openings on the back cover To prevent any unsafe situations no naked flame sources such as lighted candles should be placed on or in the vicinity Avoid heat direct sunlight and exposure to rain or water The equipme
11. has an S VHS video jack For improved picture quality connect a S Video cable with the S VIDEO input on the TV instead of connecting the VCR to the VIDEO port S Video does not provide audio audio cables must still be connected to provide sound Watching VCR If you use connection select the TV channel search If you use connection select AV If you use connection Select s video Insert videotape in the VCR and press the PLAY button EOR ee 17 DVD PLAYER Connect the video output port of DVD player to the video input port of TV Connect the left and right channels of DVD to the left and right channels of audio input of TV If your DVD player is equipped with S VHS video port For better quality picture please connect the S port to the S input port of TV Connecting the audio output ports through audio cable is a must since S port is not attached with audio How to play If you use connection please select video AV input If you use connection please select S VIDEO input CAMERA CAMCORDER VIDEO GAME SET DIGITAL CAMERA How to connect 1 Connect your digital camera camcorder videogame set to VIDEO port AUDIO R AUDIO L for mono equipment 2 S VHS quality with an S VHS camcorder is obtained by connecting the How to use 1 Select AV or S VIDEO 2 Turn on the external AV equipment HEADPHONE 1 Insert the plug into the headphone port when insert headphone will bloc
12. he appliance should be serviced by qualified service personnel when A The power supply cord or the plug has been damaged or B Objects have fallen or liquid has been spilled into the appliance or C The appliance has been exposed to rain or D The appliance does not appear to operate normally or exhibits a marked change in performance or E The appliance has been dropped or the enclosure damaged Tilt Stability All televisions must comply with recommended international global safety standards for tilt and stability properties of its cabinets design Do not compromise these design standards by applying excessive pull force to the front or top of the cabinet which could ultimately overturn the product Also do not endanger yourself or children by placing electronic equipment toys on the top of the cabinet Such items could unsuspectingly fall from the top of the set and cause product damage and or personal injury Wall or Ceiling Mounting The appliance should be mounted to a wall or ceiling only as recommended by the manufacturer Power Lines An outdoor antenna should be located away from power lines Outdoor Antenna Grounding If an outside antenna is connected to the receiver be sure the antenna system is grounded so as to provide some protection against voltage surges and built up static charges Section 810 of the National Electric Cord ANSI NFPA No 70 1984 provides information with respect to prop
13. k speaker audio output 2 Press the 4 key on the remote control to switch off the sound from the headphone and the internal loudspeakers of the TV 3 Press the cursor lift right to adjust the volume 18 Care of the screen Do not rub or strike the screen with anything hard as this may scratch mar or damage the screen permanently Unplug the screen before cleaning the screen Dust the TV by wiping the screen and the cabinet with a soft clean cloth If the screen requires additional cleaning use a clean damp cloth Do not use liquid cleaners or aerosol cleaners Mobile telephone warning To avoid disturbances in picture and sound malfunctioning of your TV or even damage to the TV keep away your mobile telephone from the TV End of life directives We are paying a lot of attention to produce environmentally friendly in green focal areas Your new receiver contains materials which can be recycled and reused At the end of its life specialized companies can dismantle the discarded receiver to concentrate the reusable materials and to minimize the amount of materials to be disposed of Please ensure you dispose of your old receiver according to local regulations 19 Product Specification Feature 17 screen XGA 1280 x 1024 Resolution Specification Screen Size 17 screen Aspect Ratio 4 3 Resolution 1280 x1024 XGA Display Area Opening 437 99 mmx270 336mm x Pixel Pitch 0 264mm x 0 264mm Display
14. nt shall not be exposed to dripping or splashing E 2 Insert the aerial plug firmly into the aerial socket at the back of the TV 3 Remote control Remove the cover of the battery compartment Insert the 2 batteries supplied Type AAA 1 5V hd D XN 4 Power Insert the power cord in the wall socket having an AC power supply 5 Turn the TV on Press the power button at the topside of the TV to turn it on If the TV is turned off the front light will also turn off OPERATING INSTRUCTIONS USE OF THE REMOTE CONTROL POWER Press to turn on off the TV The TV is never completely powered off unless it is physically unplugged 0 9 100 Digit buttons To select a TV channel CH Press A or v Aor to brows through the TV channels which are not erased To view a blocked channel use the digital buttons to access the channel and enter your access code VOL Press or to adjust the volume PC select your input source to PC SLEEP With this key you can set a time period after which the TV should switch itself to standby Press the key repeatedly to select the number of minutes The counter runs from 30 60 90 120 minutes PIP Not Supported POP Not Supported MENU Press repeatedly to display OSD menu V CHIP Press this button to setup parental control SWAP Not Supported SIZE Not Supported 7 MUTE Temporarily interrupt the sound or restore it DISPLAY P
15. our outlet consult an electrician for replacement of the obsolete outlet Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus Only use attachments accessories specified by the manufacturer Use only with a cart stand tripod bracket or table specified by the manufacturer or sold with the apparatus When a cart is used use caution when moving the cart apparatus combination to avoid injury from tip over lt A The TV should be operated only from the type of power source indicated on the label If you are not sure of the type of power supplied to your home consult your dealer or local power company Unplug this apparatus during lightning storms or when unused for long periods of time Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as power supply cord or plug is damaged liquid has been spilled or objects have fallen into apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped 16 17 18 19 20 21 This product may contain lead or mercury Disposal of these materials may be regulated due to environmental considerations For disposal or recycling information please contact your local authorities or the Electronic Industries Alliance www eiae org Damage Requiring Service T
16. r message will be displayed It is the parental control function V chip It is used to block program viewing based on the ratings by the broadcaster The default setting is to allow all programs to be viewed Viewing can be blocked by the type of program and by the categories chosen be blocked It is also possible to block all program viewing for a time period A There are two item could be defined One is TV Guidelines another one is Movie Guidelines B Setting up TV Guidelines Use Up Down arrow buttons to move around the matrix and press Right arrow button to change the value form U to B or B to U U Unblock B Block 12 ee ti i i ni C Setting up Movie Guidelines Use Up Down arrow buttons to move around the matrix and press Right arrow button to change the value from U to B or B to U 13 D CHANGE PIN Personal Identification Number is for change password to control the Vchip setup it s included three steps ENTER PIN to enable this function then ENTER NEW PIN to change a new one After that COMFIRM NEW PIN Picture Setup 1 Contrast Brightness and Saturation are adjusted from 0 to 100 2 Hue is adjusted from 0 to 100 3 Sharpness is adjusted from 0 to100 Hue is only adjusted in NTSC telecast system You can adjust contrast brightness saturation hue blacklevel and sharpness to the levels you prefer 4 Color Tone is for AV S VIDEO and TV color you
17. ress this button to Display Channel number on the right top corner MTS SAP Press this key to activate Multichannel Television Sound Stereo or Mono PRE CH To display the previously selected TV channel TV VIDEO Select your input source press repeatedly to select TV AV S VIDEO CAPTION Press this button to turn Closed Caption on Be sure you have selected Caption On in the Setup menu TO USE THE MENUS 1 Press the MENU button to display each menu 2 Use the cursor up down to select a menu item 3 Use the cursor left right to enter a submenu or enable disable the function 4 Press the MENU button to exit the menu MAIN MENU Press the MENU button into the main OSD On Screen Display Adjust item include PC SETUP gt SOUND SETUP gt OSD SETUP gt TV SETUP and PICTURE SETUP PC Setup 1 Contrast Brightness Phase Clock H Position V Position and Color are the functions for 2 Auto Adjustment is the function auto sizing for VGA input 3 Color temperature you may select or adjust color temperature warm and cold as you need When color temperature is set to user defined press the menu button you can set your favorite color by adjusting the red green or blue one The Reset To Default is user defined and is only used to reset the red green blue back to the default value 4 Reset To Default is used to reset all settings to default value Note All the Reset To Def
Download Pdf Manuals
Related Search