American Standard T050.541 Thermostat User Manual
Contents
1. Standard Installation Instructions LATHERM TO50 541 3 4 CLASSIC THERMOSTAT TRIM KIT with SEPARATE VOLUME CONTROL Thank you for selecting American Standard the benchmark of fine quality for over 100 years To ensure that your installation proceeds smoothly please read these instructions carefully before you begin ASSE 1016 M968419 REV 1 1 ROUGHING IN DIMENSIONS Recommended Tools gt Flat Blade Screwdriver Phillips Screwdriver CARE INSTRUCTIONS m Remove as much surface dirt and film using clear m To keep your new faucet looking new please follow water and soft cotton cloth as described above these simple Care instructions Use any of the following to remove tough surface film and build up Mild liquid detergents Clear ammonia free liquid glass cleaners DO NOT Non acidic non abrasive gentle liquid or fully dissolved powder cleansers mixed according to manufacturers directions Non abrasive liquid polishers DO wm Simply rinse the faucet clean with clear water gg Dry the faucet with a soft cotton cloth gg Do not use any abrasive cleaners cloths or paper towels W Do not use any cleaning agents containing acids polish abrasives or harsh cleaners or soaps m Once clean rinse faucet again with clear water to thoroughly remove cleaner or polish and blot dry with Regular and routine2. MODEL NUMBER 953950 0070A CHECK STOP COLD BLUE CARTRIDGE A918572 0070A CARTRIDGE SCREW 994053 0070A SS SS 09 923348 0070A Y HANDLE ADAPTER 953963 0070A 953960 0070A HANDLE EXTENSION THERMOSTAT CARTRIDGE 953951 0070A 5 ae 53957 0070 CALIBRATION UNIT 963434 YYYOA DEEP ROUGH KIT SOLD SEPARATELY HOT LINE FOR HELP For toll free information and answers to your questions call 1 800 442 1902 Weekdays 8 00 a m to 8 00 p m EST IN CANADA 1 800 387 0369 TORONTO 1 905 306 1093 Weekdays 8 00 a m to 7 00 p m EST Product names listed herein are trademarks of American Standard Inc American Standard Inc 2003 M968255Rev 1 1 Amirieam Standard Installation Instructions CERATHERM 3 4 CENTRAL THERMOSTAT WITH VOLUME CONTROL Thank you for selecting American Standard the benchmark of fine quality for over 100 years To ensure that your installation proceeds smoothly please Certified to comply with ANSI A112 18 1M ASSE 1016 read these instructions carefully before you begin ROUGHING IN DIMENSIONS CONNECTIONS ARE 3 4 NPT 3 4 NPT JO 3 15 16 VUT is 3 4 NPT INLET 1 5 8 2 1 2 THERMOSTATIC BATH THERMOSTATIC SHOWER INSTALLATION THERMOSTATIC SHOWER INSTALLATION USING A SHOWER INSTALLATION USING A DIVERTER
3. 6 HL PUN rue Il t 4 1 2 NPT INLET 1 2 NPT 1 2 NPT INLET TUB 5 7 8 1 5 8 2 1 2 4 THERMOSTATIC BATH THERMOSTATIC SHOWER INSTALLATION THERMOSTATIC SHOWER INSTALLATION USING A SHOWER INSTALLATION USING A DIVERTER VALVE FIXED DIVERTER VALVE FIXED SHOWER HEAD ADJUSTABLE USING A TWIN ELL DIVERTER SHOWER HEAD AND ADJUSTABLE HAND HAND HELD SHOWER ON OFF VALVE AND TWO SPOUT AND FIXED SHOWER HELD SHOWER BODY SPRAYS DIVERTER VALVE eZ unn 9 a a DIVERTER VALVE 80 86 18 OPTIONAL TOP OF TUB RIM BOTTOM OF TUB Sf TUB PORT MUST NC TUB PORT MUST BE PLUGGED BE PLUGGED IMPORTANT WHEN NOT USING A NOTE MINIMUM FLOWING PHESSURE REGUIRED FOR DIVERTER SPOUT A SEPARATE THIS SYSTEM OPERATING WITH ONE SHOWER HEAD DIVERTER VALVE MUST BE USED AND 2 BODY SPRAYS IS 40 PSI ON OFF VALVE e 9 MUST BE PLUGGED m DO NOT SOLDER DIRECTLY TO THE VALVE BODY THIS WILL DAMAGE ROUGHING IN THE VALVE WARNING THE TEMPERATURE CONTROL ELEMENT AND CHECK STOP VALVES Prepare water supplies per ROUGHING IN DIMENSIONS Make sure the finished wall is between the minimum and maximum rough dimension Install VALVE at indicated height and depth Make sure the TOP marking on the PLASTER GUARD is up Conn
4. 9 REV 1 1 CERATHERM 3 4 CLASSIC THERMOSTAT TRIM KIT with SEPARATE VOLUME CONTROL MODEL NUMBER TO50 541 M907093 YYYOA VOLUME CAP M962365 YYYOA ESCUTCHEON M909625 YYYOA FRONT COVER PLATE NW r 918049 0070A HANDLE ADAPTER A908593 YYYOA VOLUME CONTROL HANDLE 9 f 918428 0070A VOLUME HANDLE SCREW A954049 YYYOA n VOLUME HANDLE TEMPERATURE CAP A954043 YYYOA 918434 YYYOA TEMPERATURE HANDLE CAP ESCUTCHEON SCREWS SS 918416 0070A TEMPERATURE M961112 YYYOA HANDLE SCREW TEMPERATURE CONTROL HANDLE Replace the YYY with appropriate finish code CHROME 002 For toll free RUN a ae aec questions call POLISHED BRASS 099 1 800 442 1902 SATIN 295 Weekdays 8 00 a m to 8 00 p m EST IN CANADA 1 800 387 0369 TORONTO 1 905 306 1093 Weekdays 8 00 a m to 7 00 p m EST Product names listed herein are trademarks of American Standard Inc American Standard Inc 2003 M968419 REV 1 1 American Standard Installation Instructions CERATHERM ane CENTRAL THERMOSTAT WITH VOLUME CONTROL Thank you for selecting American Standard the benchmark of fine quality for over 100 years To ensure that your installation proceeds smoothly please Pepa come were S Werle E ASSE 1016 read these instructions carefully before you begin M968255Rev 1 1 ROUGHING IN DIMENSIONS CONNECTIONS ARE 1 2 NPT 1 2 NPT foe a 6 1 4 3 15 1
5. T SOLD SEPARATELY HOT LINE FOR HELP For toll free information and answers to your questions call 1 800 442 1902 Weekdays 8 00 a m to 8 00 p m EST IN CANADA 1 800 387 0369 TORONTO 1 905 306 1093 Weekdays 8 00 a m to 7 00 p m EST Product names listed herein are trademarks of American Standard Inc American Standard Inc 2003 M968480
6. T and reinstall KNOB MOUNT with arrow B pointing upwards The maximum mixed water temperature is set at 109 F at the factory This setting can be changed if desired TEMPERATURE LIMIT STOP Remove the TEMPERATURE LIMIT STOP H shaped Black Plastic part Reinstall it at the desired notch as indicated in the diagram to limit the maximum mixed water Y Y temperature to 104 F or 112 F SECURING a For 100 F adjustment turn the water supply on Turn KNOB MOUNT until the spout RING temperature is 100 F Check that arrow marking A on the KNOB MOUNT still points upward after adjusting the thermostat to 100 F If not pull out the RED LOCKING DEVICE RED LOCKING Remove KNOB MOUNT by pulling it towards you while standing directly in front of the valve E Reinstall the KNOB MOUNT so that the arrow marking A points upwards E Reinstall RED LOCKING DEVICE TRANSPOSED SUPPLY PIPING OR BACK TO BACK INSTALLATION Should the hot and cold water supply pipes have been transposed making CHECK STOP adjustment impossible proceed as follows j BLUE TO RED m Shut off water supply m Remove handle and rim E Remove check stops and re install them transposed B important note RED CHECK STOP is now on the right of the mixer body and the BLUE CHECK STOP is now on the left Turn the water supply back on and perform the temperature adjustment in step 2 esc rra M968255Rev 1 1 CERATHERM CENTRAL THERMOSTAT WITH VOLUME CONTROL
7. TOP is now on the left W Turn the water supply back on and perform the temperature adjustment in step 2 E Assemble HANDLES TRIM E M968419 REV 1 1 4 TEMPERATURE ADJUSTMENT Pull out INDEX BUTTON 1 and remove LEVER HANDLE SCREW 2 Pull off LEVER HANDLE ASSEMBLY 3 m Check that arrow marking B points to the 3 o clock position If not push the BLACK CLAMP on the SECURING RING to the right pull off KNOB MOUNT 4 and reinstall KNOB MOUNT 4 with arrow B 3 o clock position See Figure 1 SET HOT LIMIT STOP m The maximum mixed water temperature is set at 109 F at the factory This setting can be changed if desired m Remove the TEMPERATURE LIMIT STOP H shaped Black Plastic part Reinstall it at the desired notch as indicated in the diagram to limit the maximum mixed water temperature to 104 F or 112 F For 100 F adjustment turn the water supply on Turn KNOB MOUNT 4 until the spout temperature is 100 F Check that arrow A on the KNOB MOUNT 4 still points 3 o clock position after adjusting the thermostat to 100 F If not pull out the RED LOCKING DEVICE Remove KNOB MOUNT 4 by pulling it towards you while standing directly in front of the valve m Heinstall the KNOB MOUNT 4 with arrow A 3 o clock position m Reinstall RED LOCKING DEVICE E See step for LEVER HANDLE 3 installation Figure 1 ARROWS AT 3 O CLOCK POSITION AY KNOB MOUNT TEMPERATURE LIMIT STOP RED LOCKING DEVICE M96841
8. VALVE FIXED DIVERTER VALVE FIXED SHOWER HEAD ADJUSTABLE HAND HELD SHOWER ON OFF VALVE AND TWO BODY SPRAYS D D DIVERTER R VALVE 9 DIVERTER umutu 80 86 7 ON OFF TUB PORT i VALVE 18 OPTIONAL MUST BE PLUGGED e 9 TOP OF TUB RM 3 4 BOTTOM OF TUB TUB PORT MUST w S TUB PORT MUST BE PLUGGED BE PLUGGED IMPORTANT WHEN NOT USING A NOTE MINIMUM FLOWING PRESSURE REGUIRED FOR DIVERTER SPOUT A SEPARATE THIS SYSTEM OPERATING WITH ONE SHOWER HEAD DIVERTER VALVE MUST BE USED AND 2 BODY SPRAYS IS 40 PSI DO NOT SOLDER DIRECTLY TO THE VALVE BODY THIS WILL DAMAGE ROUGHING IN THE VALVE WARNING THE TEMPERATURE CONTROL ELEMENT AND CHECK STOP VALVES Prepare water supplies per ROUGHING IN DIMENSIONS Make sure the finished wall is between the minimum and maximum rough dimension Install VALVE at indicated height and depth Make sure the TOP marking on the PLASTER GUARD is up Connect the hot and cold water supplies Assemble all connecting pipes Flush lines to remove any dirt Connections are 3 4 NPT Assemble the connection pipe to one of the MIXED OUTLETS of the VALVE Cap the other MIXED OUTLET Tub port is fitted with a plug at the factory IMPORTANT INSTALL ANY REQUIRED SHUT OFF OR DIVERTER VALVES INTO THE PIPING SYSTEM PORT If the CHECK STOPS 4 5 were removed during installation ensure
9. cleaning will reduce the need for heavy cleaning and polishing If heavy cleaning is required the following procedures recommended Failure to follow these care instructions may damage the Faucet s finish TRIM INSTALLATION Remove PLASTER GUARD 1 Remove HANDLE SCREW and ADAPTER 7 from rough valve Push CAPS 2 amp 3 as shown onto CONTROL VALVES 4 Push ESCUTCHEON 5 onto CAPS 2 amp 3 and attach with BOmm SCREWS 6 to valve Push COVER PLATE 7 onto CAPS 2 amp 3 and snap into holes in ESCUTCHEON 5 to secure INSTALL HANDLES Install HANDLE ADAPTER 1 onto VOLUME CONTROL SPLINE 2 Align CROSS HANDLE 3 and push onto HANDLE ADAPTER 1 Install HANDLE SCREW 4 in CROSS HANDLE 3 and tighten with flat blade screwdriver Insert index button 5 Align the two splines in LEVER HANDLE 6 with the knob mount arrow Figure 1 and push LEVER HANDLE onto KNOB MOUNT 7 Install HANDLE SCREW 8 in LEVER HANDLE 6 and tighten with phillips screwdriver Insert index button 9 Figure 1 TRANSPOSED SUPPLY PIPING OR BACK TO BACK INSTALLATION Should the hot and cold water supply pipes have been transposed making adjustment impossible proceed as follows B Shut off water supply m Remove handle and rim Reverse steps 1 and 2 m Remove check stops and re install them transposed Important note RED CHECK STOP is now on the right of the mixer body and the BLUE CHECK S
10. ect the hot and cold water supplies Assemble all connecting pipes Flush lines to remove any dirt Connections are 1 2 NPT Assemble the connection pipe to one of the MIXED OUTLETS of the VALVE Cap the other MIXED OUTLET Tub port is fitted with a plug at the factory IMPORTANT INSTALL ANY REQUIRED SHUT OFF OR DIVERTER VALVES INTO THE PIPING SYSTEM PORT If the CHECK STOPS 4 5 were removed during installation ensure the hot and cold CHECK STOPS 4 5 are not reversed The hot CHECK STOP 4 has a red top and the cold CHECK STOP 5 has a blue top Nea CHECK STOP CHECK STOPS 4 5 are supplied in the open position COLD BLUE Closing using 5 32 4 mm hex wrench to pressure test and to check for leaks To flush lines remove the CHECK STOPS 4 5 and run water If desired the TEMPERATURE CONTROL UNIT can be removed Reinstall CHECK STOPS 4 5 and CONTROL UNIT 6 if it was removed Remove PLASTER GUARD 2 if still installed Turn on water supplies and check for leaks Reassemble PLASTER GUARD 2 and FINISH WALL CHECK STOP Beware of Freezing No water should remain HOT RED in the MIXING VALVE if freezing is a possibility Remove the CHECK STOPS 4 5 to completely drain the MIXER UNIT 1 TEMPERATURE ADJUSTMENT Unscrew PLASTER GUARD SCREWS and remove PLASTER GUARD Check that arrow marking B points vertically upwards If not push the BLACK CLAMP on the SECURING RING to the right pull off KNOB MOUN
11. r 100 F adjustment turn the water supply on Turn KNOB MOUNT until the spout RING temperature is 100 F Check that arrow marking A on the KNOB MOUNT still points upward after adjusting the thermostat to 100 F If not pull out the RED LOCKING DEVICE RED LOCKING Remove KNOB MOUNT by pulling it towards you while standing directly in front of the valve DEVICE WB Reinstall the KNOB MOUNT so that the arrow marking A points upwards E Reinstall RED LOCKING DEVICE TRANSPOSED SUPPLY PIPING OR BACK TO BACK INSTALLATION Should the hot and cold water supply pipes have been transposed making adjustment impossible proceed as follows Z CHECK STOP B Shut off water supply m Remove handle and rim E Remove check stops and re install them transposed Important note RED CHECK STOP is now on the right of the mixer body and the BL CHECK STOP is now on the left Turn the water supply back on and perform the temperature adjustment in step 2 CHECK STOP RED TO BLUE M968480 CERATHERM 3 4 CENTRAL THERMOSTAT WITH VOLUME CONTROL MODEL NUMBER 912647 0070A O RING A953971 0070A CHECK STOP COLD BLUE A994352 0070A CARTRIDGE I 923348 0070A E HANDLE ADAPTER N K 918428 0070A D CARTRIDGE SCREW Z 953963 0070A 954040 0070A O THERMOSTAT HANDLE EXTENSION CARTRIDGE A953972 0070A CHECK STOP HOT RED 912647 0070A j tl ma O RING CALIBRATION UNIT 963434 YYYOA DEEP ROUGH KI
12. the hot and cold CHECK STOPS 4 5 are not reversed The hot CHECK STOP 4 has a red top and the cold CHECK STOP 5 has a blue top eie CHECK STOP CHECK STOPS 4 5 are supplied in the open position T COLD BLUE Closing using 5 32 4 mm hex wrench to pressure test and to check for leaks To flush lines remove the CHECK STOPS 4 5 and run water If desired the TEMPERATURE CONTROL UNIT can be removed Reinstall CHECK STOPS 4 5 and CONTROL UNIT 6 if it was removed Remove PLASTER GUARD 9 if still installed Turn on water supplies and check for leaks Reassemble PLASTER GUARD 2 and FINISH WALL Beware of Freezing No water should remain in the MIXING VALVE if freezing is a possibility CHECK STOP Remove the CHECK STOPS 4 5 to completely HOT RED drain the MIXER UNIT 1 TEMPERATURE ADJUSTMENT Unscrew PLASTER GUARD SCREWS and remove PLASTER GUARD Check that arrow marking B points vertically upwards If not push the BLACK CLAMP on the SECURING RING to the right pull off KNOB MOUNT and reinstall KNOB MOUNT with arrow B pointing upwards The maximum mixed water temperature is set at 109 F at the factory N F TEMPERATURE This setting can be changed if desired LIMIT STOP Remove the TEMPERATURE LIMIT STOP H shaped Black Plastic part Reinstall it at the desired notch as indicated in the diagram to limit the maximum mixed water ut temperature to 104 F or 112 F SECURING ye Fo
Download Pdf Manuals
Related Search