American Standard M968498 Indoor Furnishings User Manual
Contents
1. Insert POWER CORD CONNECTOR 13 through POWER SUPPLY GROMMET 12 Insert POWER CORD 14 into SPLIT PLUG 11 Push SPLIT PLUG 11 into POWER SUPPLY GROMMET 12 to seal Fig 2g 7 Insert POWER SUPPLY CONNECTOR 13 into RECEPTOR 15 on the CIRCUIT BOARD 3 Fig 2c 8 Install CIRCUIT BOARD 3 into ENCLOSURE 5 with SENSOR WIRE 7 under BOARD Fig 2d 9 Insert SENSOR WIRE CONNECTOR 8 into CIRCUIT BOARD RECEPTOR 10 slot Fig 2f 10 Connect wires from SENSOR to SOLENOID VALVE 6 Red to Black to Fig 2d 11 Replace ENCLOSURE COVER 1 Tighten cover screws firmly Fig 3 Unit 1 Unit 2 Unit 3 TWO PIECE a oa GROMMET E FOR AC VERSION Fig 4a MULTI HOOK UP Fig 3 4 1 See AC Version Electrical Hook up for first unit of CROMER 8 the Multi hook up 2 Remove ENCLOSURE COVERS from all ENCLOSURES 3 Remove SOLID BLACK INSERT 1 from right side of ENCLOSURE 1 and replace with gray 2 PIECE GROMMET 3 Replace solid black inserts on Unit 2 with gray 2 PIECE GROMMET 3 4 Take the 10 ft EXTENSION 2 from Unit 2 and install into right side of Unit 1 and Left side of Unit 2 insealing wire into SPLIT PLUG 7 as shown in Fig 4a Push SPLIT PLUG 7 into GROMMET 8 Feed the gray 8 ft EXTENSION 2 through ROUND 5 Insert CONNECTOR from 10 ft EXTENSION 2 GROMMETS 3 and U GROMMETS 5 as illustrated above into CIRCUIT BOARD2. RECEPTOR 4 top of Unit 1 as shown in Fig 3 6 Insert other end of 10 ft EXTENSION into LOWER U GROMMET 5 of Unit 2 approximately 4 from connector Fig 3 Push SPLIT PLUG 7 into GROMMET 8 to seal 7 Insert connector of 10 ft EXTENSION into lower receptor as shown in fig 3 on CIRCUIT BOARD 6 of Unit 2 8 Feed gray sensor wire 9 from Unit 2 through upper U GROMMET 10 of Unit 2 ENCLOSURE 4 from connector Fig 3 Insert wire into SPLIT PLUG 7 Push SPLIT PLUG 7 into GROMMET 8 to seal Fig 4a 9 Insert GROMMET 2 back into ENCLOSURE Fig 4b 10 Reinstall Circuit Board 3 into Enclosure with all wires under Board Fig 4b 11 Connect Unit 2 Red and Black Sensor wires To 2 solenoid valve Red to Black to Fig 4b 12 Repeat Steps 3 through 11 for remaining Units in Multi Hook up MAINTENANCE fh HAND WASH SENSOR OPERATION Fig 1 When the Sensor detects a user the water immediately starts to flow Water flow will stop Two seconds after user is out of sensor range The off delay allows the user to comfortably move his hands without the flow cycling on to off As a precaution a safety timer will turn off the water after the sensor has been blocked for 59 seconds The water will stay off until the blockage is removed from the detection zone Detection Zone 2 10 50mm 250mm Default Set at Factory 6 150mm A HOW TO CHANGE SENSOR RANGE Factory set at 6 Fi
3. ELECTRICAL INSTALLATION DC VERSION BATTERY Fig 1 1 Remove ENCLOSURE COVER 1 Fig 1 2 Feed the WIRE CONNECTORS 2 through the top of ENCLOSURE 5 Fig 1a 3 Remove GROMMET 4 from ENCLOSUR 5 Fig 1 4 Feed the gray SENSOR WIRE 7 through GROMMET 4 4 from CONNECTOR Fig 1b amp 1d Insert gray SENSOR WIRE 7 into SPLIT PLUG 9 Push SPLIT PLUG 9 into GROMMET 4 to seal Fig 1d 5 Insert GROMMET 4 back into ENCLOSURE 5 Fig 1c 6 Install BATTERY 11 onto DC circuit board Fig 1e Note For BATTERY PACK installation see Install Battery page 7 7 Install CIRCUIT BOARD 3 into ENCLOSURE 5 with SENSOR WIRE 7 under BOARD Fig 1c 8 Insert SENSOR WIRE CONNECTOR 8 into CIRCUIT BOARD RECEPTOR 10 Fig 1e 9 Connect wires from SENSOR to SOLENOID VALVE 6 Red to Black to Fig 1c 10 Replace ENCLOSURE COVER 1 Tighten cover screws firmly H AC VERSION Fig 2 oP NUTONE Gisconnect AC power supply 1 Remove ENCLOSURE COVER 1 Fig 2 2 Feed the WIRE CONNECTORS 2 through the top of ENCLOSURE 5 Fig 2a 3 Remove GROMMET 4 from ENCLOSUR 5 Fig 2 4 Feed the gray SENSOR WIRE 7 through GROMMET 4 4 from CONNECTOR Fig 2b Insert gray SENSOR WIRE 7 into SPLIT PLUG 9 Push SPLIT PLUG 9 into GROMMET 4 to seal Fig 2e 5 Insert GROMMET 4 back into ENCLOSURE 5 Fig 2d 6 Remove SPLIT PLUG 11 from POWER SUPPLY GROMMET 12
4. LENOID VALVE ASSEMBLY M950251 0070A AC SOLENOID VALVE ASSEMBLY M962387 0070A MOUNTING SCREW KIT A91 3202 0070A WASHER A923654 0070A BATTERY 6VCR P2 A922251 0070A SOLID GROMMET A924162 0070A SUPPLY HOSE A918462 0070A SOLENOID SCREWS 605P400 M962389 0070A SOLENOID amp SCREWS A950487 0070A CIRCUIT BOARD DC A950507 0070A 044912 0070A FILTER MOUNTING NUT A922267 0070A ROUND GROMMET A950509 0070A SUPPLY STOP A922272 0070A U GROMMET A922290 0070A POVVER SUPPLY GROMMET Replace the YYY with appropriate finish code CHROME 002 M950169 0070A POWER SUPPLY s nuy A950489 0070A CIRCUIT BOARD AC amp MULTI AC HOT LINE FOR HELP For toll free information and answers to your questions call 1 800 442 1902 Weekdays 8 00 a m to 8 00 p m EST A922265 0070A 10 ft MULTI EXTENSION WIRE for 6057 series only IN CANADA 1 800 387 0369 TORONTO 1 905 306 1093 Weekdays 8 00 a m to 7 00 p m EST Product names listed herein are trademarks of American Standard Inc American Standard Inc 2005 M968809 Rev 1 2 10 Armtricam Standard M968809 Rev 1 2
5. O O18 GOD INSTALLATION fl INSTALL SPOUT ASSEMBLY Fig 1 TNO supplies before beginning 1 Optional Assemble DECK PLATE 1 and PUTTY PLATE 2 to FAUCET BODY 3 with SCREW 4 Fig 1 2 Insert WIRES 5 FLEX HOSE 6 and SPOUT SHANK 7 through center hole of mounting surface Fig 1a 3 Assemble C WASHER 8 STAR WASHER 9 and LOCKNUT 10 onto threads of SPOUT SHANK 7 from underside of mounting surface Fig 1b 4 Align FAUCET 3 and tighten LOCKNUT 10 If using DECK PLATE 1 hand tighten DECK PLATE SPIN NUTS 11 to secure FAUCET 3 to mounting surface Fig 1b A MOUNT ENCLOSURE Fig 2 1 Determine location of ENCLOSURE 1 It must be located with in the 14 856mm by 21 533mm shaded area shown in Figure 2 in order for electrical connections from the spout assembly to be made NOTE ENCLOSURE SUPPLY HOSE is 20 Distance between wall supply and ENCLOSURE 1 must be taken into consideration 2 Remove 4 screws from COVER 2 and pull off COVER 2 Hold the ENCLOSURE 1 in desired location and mark the four mounting hole locations as shown Fig 2 3 The ENCLOSURE 1 works best if secured to a wall stud or cross brace within the wall using the SCREWS 3 supplied If the ENCLOSURE 1 is to be installed on a tile or plaster wall the ANCHORS 4 and SCREWS 3 should be used 4 For installations on drywall or tiled walls use ANCHORS 4 and SCREWS 3 for securing ENCLO
6. SELECTRONIC Proximity Faucets Cast Spout and two Goose Neck Sizes Certified to commen ie a etme aera Replacement Parts 10 2005 American Standard M968809 Rev 1 2 Installation Instructions American Standard NOTE TO INSTALLER Please give this manual to the customer after installation To learn more about American Standard Faucets visit our website at www us amstd com or U S customer s e mail us at faucetsupport amstd com For Parts Service Warranty or other Assistance please call 1 800 442 1902 In Canada 1 800 387 0369 In Toronto Area only 1 905 3061093 Thank you for selecting American Standard the benchmark of fine quality for over 100 years To ensure that your installation proceeds smoothly please read these instructions carefully before you begin U N P AC KI NG All American Standard Faucets Are Water Tested At Our Factory Some Residual Water May Remain In The Faucet During Shipping 1 Remove the fitting and loose items from the carton The illustration below shows the fitting and all loose items after they have been removed from the carton Some items may be packaged partially assembled to other items 1 Selectronic Spout Assembly 2 Mounting Kit 3 Electrical Enclosure 4 Supply Hose 5a DC Power Supply for 6055 series 5b AC Power Supply for 6056 series PRODUCT No s 5c 10 ft Extension Wire for 6057 series 6 Circuit board 7 4 Deck plate optional
7. SURE 1 to finished wall Drill four 1 4 dia holes a minimum of 1 3 4 deep Insert the four ANCHORS 4 flush with face of the finished wall Align the ENCLOSURE 1 and Install the MOUNTING SCREWS 3 Tighten to secure ENCLOSURE 1 to mounting surface E CONNECT SPOUT HOSE TO ENCLOSURE Fig 3 1 Connect SUPPLY NUT 1 from spout assembly to nipple on top of ENCLOSURE 2 Tighten with adjustable wrench to make a water tight connection Fig 3 FE CONNECT WATER SUPPLY TO ENCLOSURE AND WALL SUPPLY Fig 4 ek If using the optional Mixing Valve See Sheet M968808 for installation instructions 1 Insert FIBER WASHER 4 into SUPPLY NUT 1 on ENCLOSURE 2 2 Connect SUPPLY NUT 1 on ENCLOSURE 2 to FLEXIBLE SUPPLY HOSE 3 Tighten to make a water tight connection Use two wrenches to tighten if necessary Fig 4 3 Connect FLEXIBLE SUPPLY 3 directly to wall supply Connection on FLEXIBLE SUPPLY 3 is 3 8 compression Use adjustable wrench to tighten connection Do not over tighten Fig 4a Note FLEXIBLE SUPPLY 3 measures 20 from the bottom of the ENCLOSURE 1 base If additional supply length is required installer must purchase parts separately Important If FLEXIBLE SUPPLY 3 is too long loop to avoid kinking ENCLOSURE MOUNTING HOLES le 2 3 4 71mm NOTE If using Mixing Valve optional See Sheet M968808 for installation instructions
8. cket 5 Pull out the STRAINER 4 and clean with an old toothbrush Rinse thoroughly with water 6 Install the STRAINER 4 back in its place and tighten with a 7 16 socket Caution do not over tighten strainer Note It is recommended to clean strainer every 6 months 7 Replace ENCLOSURE COVER Tighten cover screws firmly fa HOW TO CLEAN AND REMOVE THE AERATOR Fig 5 1 Remove AERATOR HOUSING 1 with KEY supplied with faucet 3 Remove AERATOR 2 from HOUSING 1 2 Clean the AERATOR SCREENS 3 with a old tooth brush to remove dirt 4 Rinse Clean with water Reassemble and install into spout end Be sure black seal washer is in place fi HOW TO CONVERT RIGID GOOSE NECK SPOUT TO SWING SPOUT Fig 6 The GN SPOUT is shipped from the factory as a rigid assembly To convert the GN SPOUT into a SWING SPOUT proceed as follows 1 Remove SET SCREW 1 from back of GN SPOUT A e a UEO 2 with a flat blade screwdriver Fig 6 x 4 SET SCREW r FOR SWIVEL a E SPOUT 2 Install SWIVEL SET SCREW 3 into opening in the f GN SPOUT 2 SWIVEL SET SCREW 3 is found in hardware bag within product box GENERAL CLEANING Fig 7 1 For general cleaning use a damp soft cloth to clean the spout and the sensor 2 For cleaning dirt use a soft cloth with diluted dish washing detergent Wipe the area using a wet cloth and dry using a soft cloth Do not scratch the sensor when cleaning Avoid using an
9. g 2 1 Setting the Detection Zone Distance Remove cover from ENCLOSURE Disconnect GRAY SENSOR WIRE 1 from circuit board then reconnect 2 While the SENSOR CONTROL LED 2 is blinking slowly place your hand 1 2 in 830 50mm in front of the sensor Fig 2a 3 When the LED stops blinking and stays ON move your hand to the desired position and hold in place until the LED begins to blink again Fig 2a 4 Once the SENSOR CONTROL LED 2 begins to blink again remove your hand from the detection zone When the flashing stops the detection distance is set ki HOW TO INSTALL AND CHANGE BATTERY Fig 3 1 To install New BATTERY 1 align and press down BATTERY 1 contacts facing downward into position until tabs lock into place To remove the BATTERY 1 spread the two tabs on the HOLDER 2 with your thumbs The BATTERY 1 will release 2 Remove the OLD BATTERY 1 3 Install NEW BATTERY 1 contacts facing downward into HOLDER 2 and press down into position until tabs lock into place 2 30mm 50mm 2 BLINKING LED BATTERY HOLDER LOCKING TABS 7 E HOW TO CLEAN FILTER Fig 4 ZATON Gisconnect AC power supply 1 Remove ENCLOSURE COVER 2 Close SUPPLY STOP 5 with 4mm Hex wrench Note Keep water flowing out of faucet while shutting off 3 Pull off Red 1 and Black 2 CONNECTORS from Ra ae SOLENOID VALVE 3 CLEAN p SCREENS 4 Unthread STRAINER 4 using a 7 16 so
10. must be ordered separately 8 8 Deck plate optional must be ordered separately 9 Mixing Valve optional must be ordered separately 10 Key for vandal resistant aerator PRODUCT No s 5 1 4 GN Spout PRODUCT No s inods poiiseg esoouy Zz Ajddnsg 1 MmOd 8SooUd 1 6055 105 6055 102 6056 105 6056 102 6057 105 6057 102 6055 155 6055 153 6056 155 6056 153 6057 155 6057 153 6055 165 6055 163 6056 165 6056 163 6057 165 6057 163 JONPOJd 21U01 29 S y 1 p10 O MOH ju a 6UIS YUIS J0H e Huls e yonpolg eseg 19 U J UI SJUIS JOH PUE o jeuoldo eid 499q eld 49eq 605XTMV S Q U P OD PUL JOH e SUIS JOH PUR jJeuolNdo aaqjeA UIXIN ane A UIXIN Fig 1 Roughing in Dimensions 141mm 5 1 2 MOUNTING SURFACE 49mm 2 32mm 1 1 4 gt 125mm e 381mm i 15 GENERAL DESCRIPTION Electronic faucet with proximity operation Vandal resistant solid brass construction single post mounting Operates on DC battery or AC permanent power In line strainer for solenoid is integral Single inlet 3 8 compression built in checks and flexible stainless steel 15 reach inlet hose for spout connection TOOLS REQUIRED Fig 2 Channel Locks Adjustable Wrench Plumbers Putty or Caulking Phillips Screwdriver Flat Blade Screwdriver Electric Drill amp 1 4 Drill Bit Tape Measure N
11. ything that may scratch the spout surface Never use polishing power detergent or a nylon scrub brush They will damage the surface of the spout or Sensor Q How will know if battery needs to be replaced A Valve does not open and sensor blinks 2 times interrupted by pause for up to 7 days Q Why has the flow rate of the faucet reduced significantly A Check and clean aerator and strainer Q There is no flow out of faucet when I m in the sensor range A Check sensor If sensor blinks 2 times interrupted by pause replace battery or call 1800 442 1902 Q Why does the faucet operate the opposite of expected Turns On when not in sensor range but turns off when in sensor range A Sensor wires to solenoid are reversed Black to amp Red to is correct Q What is the normal operating pressure range A Faucet will operate with supply pressures ranging from 20 80 psi SELECTRONIC Armtrican Standard LAVATORY FAUCETS PRODUCT NUMBERS Cast Spout Cast Spout M923827 YYYOA 6055 105 6056 105 6057 105 2 2 GPM AERATOR 6055 102 6056 102 6057 102 066508 YYYOA 5 1 4 GN Spout 0 5 GPM AERATOR 6055 155 6056 155 6057 155 6055 153 6056 153 6057 153 M962388 0070A i SENSOR KIT 6 GN Spout CCCG 6055 165 6056 165 6057 165 6055 163 6056 163 6057 163 A923672 0070A FAUCET SUPPLY HOSE D 0 ol N N pa x r O D M962411 0070A MOUNTING KIT M950250 0070A DC SO
Download Pdf Manuals
Related Search