American Standard 4508.801 Indoor Furnishings User Manual
Contents
1. HANDLE SCREW 918049 0070A ADAPTER 994053 0070A CARTRIDGE 918555 0070A M906617 0070A ATTACHMENT NUT M953006 0070A TEE amp HOSE KIT gm i o24220 0070A SUPPLY NUT 066116 YYYOA DRAIN STOPPER 066117 YYYOA Massa en 2 FLANGE KIT MPLETE DRAIN ASSEMBLY M962403 YYYOA LIFT ROD AND KNOB 072574 0070A EXTENSION ROD M961711 0070A c TAILPIECE INSERT 066118 0070A PIVOT ROD KIT 070847 0070A CLIP 070532 0040A TAILPIECE POP UP DRAIN ASSEMBLY BEFORE 04 06 m M962402 YYYOA SPOUT KIT 066070 YYYOA AERATOR M907559 YYYOA SPOUT ESCUTCHEON A911914 0070A SEAL Replace the YYY with L M961733 0070A appropriate finish code SPOUT MTG KIT CHROME O08 SATIN NICKEL 295 m M962404 YYYOA HANDLE KIT i M962544 YYYOA STOPPER ASSEMBLY M952430 0070A CABLE ASSEMBLY M962457 YYYOA FLANGE ASSEMBLY M952425 YYYOA DRAIN ASSEMBLY M922872 0070A CAM SEAT INSERT M962552 0070A d CAM ASSEMBLY M919660 0020A d e 6 TAILPIECE NOT INCLUDED lt D M913207 0070A WITH FAUCET TAILPIECE INSERT A919661 0020A TAILPIECE M962458 0070A DRAIN MOUNTING KIT M968832 Rev 1 3 HOT LINE FOR HELP For toll free information and answers to your questions call 1 800 442 1902 Weekdays 8 00 a m to 6 00 p m EST IN CANADA 1 800 387 0369 TORONTO 1 905 306 1093 Weekdays 8 00 a m to 7 002. A Tighten THREAD ON STEM SCREW 3 to secure ADAPTER 1 TO DECK ADAPTER Find correct position of LEVER HANDLE ASSEMBLY 4 by adjusting male teeth on ADAPTER 1 to female teeth in HANDLE 4 Thread LEVER HANDLE ASSEMBLY 4 onto DECK ADAPTER 5 until snug against mounting surface Figure A SPLINE END DOW 1 1 TEST INSTALLED FITTING With HANDLES 1 in OFF position turn on WATER SUPPLIES 2 and check all connections for leaks m Remove AERATOR 3 Operate both HANDLES 1 to flush water lines thoroughly Replace AERATOR 3 X 1 2 CHECK DRAIN CONNECTIONS Ea C W Operate POP UP KNOB 5 and fill Sink with water Check that DRAIN STOPPER 4 makes a good seal and retains water in Sink If STOPPER 4 does not seal properly please refer to Troubleshooting Guide in these instructions Release POP UP KNOB 5 down and check all drain connections and P trap for leaks IW Tighten if necessary INK AA HEVVVVVVVVVVVN P TRAP 1 3 CARE INSTRUCTIONS HANDLE ASSEMBLY DO SIMPLY RINSE THE PRODUCT To change direction of handle rotation proceed as follows CLEAN WITH CLEAR WATER DRY a Turn valve to OFF position Unthread HANDLE WITH A SOFT COTTON FLANNEL BASE 1 from DECK ADAPTER 2 CLOTH Pull HANDLE ASSEMBLY off VALVE STEM 3 a Remove SPRING CLIP 4 Lift STOP WASHER 5 i turn 90 and replace Replace SPRING CLIP 4 BO NOT DO NOT CLEAN THE Find cor
3. American Standard Installation Instructions PRINCETON 4508 801 Spread Lavatory Faucet with Speed Connect Drain Congratulations on purchasing your American Standard faucet with Speed Connect drain a feature found only on American Standard faucets T sn Speed Connect Drain Certified to comply with ANSI A112 18 1 Fewer parts installs in less time M968832 Rev 1 3 Never needs adjustment Guaranteed to seal properly the first time every time To ensure that your installation proceeds smoothly please read these instructions carefully before you begin Recommended tools So 3 D CE 3 SNO R rh b Screwdriver Channel Locks Adjustable Wrench Tubing Cutter 1 INSTALL SPOUT W Insert SPOUT 1 and CABLE CONNECTOR 12 through center hole making sure the SPOUT ESCUTCHEON 2 and SEAL WASHER 3 are properly seated m Assemble RUBBER WASHER 4 BRASS WASHER 5 and LOCKNUT 6 onto SPOUT SHANK 7 from under side of sink Make sure SPOUT 1 is centered in the mounting hole and the slot in the BRASS WASHER 5 faces toward the rear of the sink m Tighten LOCKNUT 6 firmly Fig A 1A iaaa cos McEcul main supply m Place RUBBER RING 9 into SCUTCHEON 10 W install LOCKNUT 11 onto VALVE BODY 8 From under side of mounting surface install VALVE BODY 8 through valve mounting holes Threads of VALVE BODY 8 should extent at least 5 16 of a inch above mounting surface to
4. OR m Thread CABLE CONNECTOR 1 clockwise onto DRAIN BODY CONNECTION 2 and hand tighten Fig A Your new POP UP DRAIN installation is now complete Fig B Note Tailpeice on pop up drain is 1 1 4 O D Fig B 8 CHECK OPERATION OF POP UP Operate LIFT KNOB 1 to verify that STOPPER 2 opens and closes Note If STOPPER 2 does not open and close properly then refer to the troubleshooting section of these instructions MAKE WATER SUPPLY AND WASTE CONNECTIONS NOTE FLEXIBLE SUPPLIES OR BULL NOSE RISERS NOT INCLUDED AND MUST BE PURCHASED SEPARATELY Thread TEE BODY 4 to SPOUT SHANK 5 Thread HOSE CONNECTOR 6 6A to VALVE CONNECTIONS 7 7A Connect water supply to VALVE BODIES 1 1A with 1 2 IPS FLEXIBLE SUPPLIES 2 or 3 8 O D BULL NOSE RISERS 3 Use adjustable wrench to tighten connections Do not over tighten Be careful not to kink copper supply when bending Use tubing cutter to cut to proper length Connect HOT water supply to inlet of left SHANK and COLD water supply to right SHANK using sealant appropriate connectors and COUPLING NUTS Connect 1 1 4 O D tailpiece on POP UP DRAIN to waste outlet 1 2 PIPE THREAD 3 BULLNOSE niserss COMPRESSION 1 FLEXIBLE 3 SUPPLIES 3 8 COMPRESSION CONNECTION M968832 Rev 1 3 INSTALL HANDLES Push ADAPTER 11 on VALVE STEM 2 so that the hole of the ADAPTER 1 without a spline is facing up See figure
5. he Cable Connector 1 clockwise onto the Drain Body Connection 2 and hand tighten Fig A STOPPER B STOPPER REMOVAL PROCEDURE Disconnect the Cable from the Drain by threading the Cable Connector 1 counter clockwise Fig A Look at the area on the Drain Body where the Cable was attached and locate the component labeled as Cam and Cam Cap in the illustration Fig B Use fingers or small screwdriver under either side of the Cam Cap to pry it out from the Drain Fig D Remove the Cam by pulling it straight out while wiggling gently to loosen the Rubber Seal Fig E The Stopper can now be removed by lifting it out of the Drain Fig F Ae as REMOVE CAM CAP M968832 Rev 1 3 STOPPER INSTALLATION PROCEDURE The Stopper can be installed two ways Locked Mode Stopper cannot be removed or Unlock Mode Stopper is removable Locked Mode Look at the Plastic Loop at the bottom of the Stopper and notice that the Loop is on one side of the Stopper Fig G To install the stopper in Locked mode insert the Stopper into the Drain so that the Plastic Loop is facing toward the rear of the Sink and the American Standard logo is facing front Rotate Stopper slightly if necessary so that the Stopper slides all the way down Fig G He install the Cam into the Drain rotating the Cam if necessary to make sure it is fully inserted Fig J U LOOP TOWARD REAR OF SINK Re install the Cam Cap making sure the gu
6. ide teeth are facing Gor outward If the Cam Cap does not snap into place then rotate DRAIN the Cam to make sure it is fully inserted Fig K Re attach Cable See CABLE ADJUSTMENT PROCEDURE in Locked Mode Troubling Shooting Guide to complete installation Stopper will be Vandal Proof in Locked mode and not be removable Unlocked Mode Look at the Plastic Loop at the bottom of the Stopper and notice that the Loop is on one side of the Stopper Fig H To install the stopper in Unlocked mode insert the Stopper into the Drain so that the Plastic Loop is facing toward the front of the Sink and the American Standard logo is facing rear Rotate Stopper slightly if necessary so that the Stopper slides all the way down Fig H Re install the Cam into the Drain rotating the Cam if necessary to make sure it is fully inserted Fig J LOOP TOWARD FRONT OF SINK Re install the Cam Cap making sure the guide teeth are facing Ec outward If the Cam Cap does not snap into place then rotate DRAIN the Cam to make sure it is fully inserted Fig K Re attach Cable See CABLE ADJUSTMENT PROCEDURE in Unlocked Mode Troublingshooting Guide to complete installation Stopper will be in Unlocked mode and removable INSTALL CAM CAP M968832 Rev 1 3 PRINCETON Spread Lavatory Faucet with Pop up Drain MODEL NUMBER M962474 YYYOA LIFT ROD AND KNOB 2 M962248 0070A DECK ADAPTER KIT
7. p Fig B Thread ESCUTCHEON 10 onto VALVE BODY 8 until snug against internal stop If necessary adjust LOCKNUT 11 Hand tighten LOCKNUT 11 to secure VALVE BODY 8 Repeat above steps for opposite VALVE BODY 8A MOUNTING Y SURFACE mai 2 POP UP DRAIN E Remove CLEAR PLASTIC COVER 1 m Remove CARDBOARD SPACER 2 from under DRAIN POP UP 3 m Tighten TAILPIECE 4 on DRAIN BODY before installing DRAIN BODY Fig B J NN 27 qe 3 REMOVE FLANGE E Thread FLANGE 1 counter clockwise and remove FLANGE 1 and FOAM GASKET 2 from drain body Fig A E Thread LOCKNUT 3 clockwise to bottom of drain body Push GASKET 4 down against LOCKNUT 3 Fig B INSTALL DRAIN FROM BELOW FIXTURE ESS From under side of SINK m Tighten LOCKNUT 1 firmly with Adjustable install DRAIN BODY 1 up Wrench or Channel Locks through drain outlet Note No plumber s putty or caulk is required The CABLE ATTACHMENT POINT 2 must face towards the rear of the SINK Install FOAM GASKET 3 and FLANGE 4 onto drain body from above SINK and tighten FLANGE 4 firmly FLANGE GASKET AND POP UP KNOB Check DRAIN FLANGE in SINK to ensure that WHITE FOAM GASKET 3 is fully compressed and not visible Fig A WHITE FOAM GASKET POP UP KNOB 1 must be fully down Fig B M968832 Rev 1 3 7 ATTACH CABLE CONNECT
8. p m EST IN MEXICO 01 800 839 12 00 Product names listed herein are trademarks of American Standard Inc AS America Inc 2008
9. rect pasion of HANDLE ASSEMBLY by adjusting PRODUCT WITH SOAPS ACID male teeth on VALVE STEM 3 to female teeth in HANDLE POLISH ABRASIVES HARSH Thread HANDLE ASSEMBLY onto DECK ADAPTER 2 CLEANERS OR A CLOTH WITH until snug against mounting surface A COARSE SURFACE If pod drips operate handles several times from OFF to ON position Do not force handles turn only 90 SA M968832 Rev 1 3 Speed Connect Drain Troubleshooting Guide If sink does not hold water even though Stopper is in the down position Follow CABLE ADJUSTMENT PROCEDURE If eara ue does not raise up fully or sink drains too slowly Follow CABLE ADJUSTMENT PROCEDURE If you need to remove the Stopper Follow STOPPER REMOVAL PROCEDURE If you would like the ability to remove your Stopper simply by lifting it out of the drain Follow STOPPER INSTALLATION PROCEDURE for Unlocked mode CABLE ADJUSTMENT PROCEDURE Disconnect the Cable from the Drain by threading the Cable Connector 1 counter clockwise Fig A Look at the area on the Drain Body where the Cable was attached and locate the component labeled as Cam in the illustration Fig B Use a small screwdriver to rotate the Cam in the clockwise direction as far as it will go At this point the Stopper should be in the UP position Fig B C Push DOWN on the Lift Knob to make sure it is fully down Fig C Re attach the Cable to the Drain Body Connection 2 by threading t
Download Pdf Manuals
Related Search