American Standard 3698.016 Indoor Furnishings User Manual
Contents
1. 1 4 Q D tailpiece on POP UP DRAIN to waste outlet 1 2 PIPE THREAD 3 3 8 0 D _ wag COMPRESSION NUT S FLEXIBLE 3 SUPPLIES 3 8 COMPRESSION CONNECTION 43167 Rev 1 3 INSTALL HANDLES m See separate installation instructions supplied with handle kits for installing handles onto fitting 1 1 TEST INSTALLED FITTING With HANDLES 1 in OFF position turn on WATER SUPPLIES 2 and check all connections for leaks Remove AERATOR 3 Operate both HANDLES 1 to flush water lines thoroughly Replace AERATOR 3 AA me Tt j 1 2 CHECK DRAIN CONNECTIONS E Operate POP UP KNOB 5 and fill Sink with water Check that DRAIN STOPPER 4 makes a good seal and retains water in Sink If STOPPER 4 does not seal properly please refer to Troubleshooting Guide in these instructions WVVVVV VV VIE Release POP UP KNOB 5 down and check all drain connections and P trap for leaks m Tighten if necessary TO CLEAN AERATOR J ta Z pP TRAP AERATOR 3 may accumulate dirt causing distorted and reduced water flow Unscrew and remove AERATOR 3 and rinse clean Replace AERATOR 3 and operate handles several times from OFF to ON position Do not force handles turn only 90 1 3 CARE INSTRUCTIONS HANDLE ASSEMBLY N DO SIMPLY RINSE THE PRODUCT To change direction of handle rotation CLEAN WITH CLEAR WATER DRY proceed as follows WITH A SOFT COTTON FLANNEL a2. inserted Fig J Uf Loop Towarp REAR OF SINK Re install the Cam Cap making sure the guide teeth are facing QAQA outward If the Cam Cap does not snap into place then rotate DRAIN the Cam to make sure it is fully inserted Fig K Re attach Cable See CABLE ADJUSTMENT PROCEDURE in Locked Mode Troubling Shooting Guide to complete installation Stopper will be Vandal Proof in Locked mode and not be removable Unlocked Mode Look at the Plastic Loop at the bottom of the Stopper and notice that the Loop is on one side of the Stopper Fig H To install the stopper in Unlocked mode insert the Stopper into the Drain so that the Plastic Loop is facing toward the front of the Sink and the American Standard logo is facing rear Rotate Stopper slightly if necessary so that the Stopper slides all the way down Fig H Re install the Cam into the Drain rotating the Cam if necessary to make sure it is fully inserted Fig J f LOOP TOWARD FRONT OF SINK Re install the Cam Cap making sure the guide teeth are facing Q outward If the Cam Cap does not snap into place then rotate DRAIN the Cam to make sure it is fully inserted Fig K Re attach Cable See CABLE ADJUSTMENT PROCEDURE in Unlocked Mode Troublingshooting Guide to complete installation Stopper will be in Unlocked mode and removable INSTALL CAM CAP 43167 Rev 1 3 AMARILIS WIDESPREAD LAVATORY FAUCET MODEL NUMBE
3. 12 onto VALVE BODY 183 From under side of mounting surface install VALVE BODY 13 through valve mounting holes Threads of VALVE BODY 13 should extent at least 5 16 of a inch above mounting surface top Fig B Thread DECK ADAPTER 10 onto VALVE BODY 13 until snug against internal stop If necessary adjust LOCKNUT 11 Tighten LOCKNUT 41 with WRENCH 8 supplied to secure VALVE BODY 13 Repeat above steps for opposite VALVE BODY 13A 10 gt MOUNTING 5 16 MIN SURFACE y 27 Fig B i e s LI 11 F 13 8 _ 2 POP UP DRAIN m Remove CLEAR PLASTIC COVER 1 m Remove CARDBOARD SPACER 2 from under DRAIN POP UP 3 E Tighten TAILPIECE 4 on DRAIN BODY before installing DRAIN BODY Fig B 3 REMOVE FLANGE E Thread FLANGE 1 counter clockwise and remove FLANGE 1 and FOAM GASKET 2 from drain body Fig A E Thread LOCKNUT 3 clock wise to bottom of drain body Push GASKET 4 down against LOCKNUT 3 Fig B INSTALL DRAIN FROM BELOW FIXTURE From under side of SINK S Tighten LOCKNUT 1 firmly with Adjustable install DRAIN BODY 1 up Wrench or Channel Locks through drain outlet Note No plumber s putty or caulk is required The CABLE ATTACHMENT POINT 2 must face towards the rear of the SINK Install FOAM GASKET 3 and FLANGE 4 onto
4. AAmtrican Standard Installation Instructions AMARILIS 3801 000 Spread Lavatory Faucet with 3841 000 Speed Connect Drain Congratulations on purchasing your American Standard faucet with Speed Connect drain a feature found only on American Standard faucets Speed Connect Drain Certified to comply with ANSI A112 18 1 e Fewer parts installs in less time 43167 Rev 1 3 e Never needs adjustment e Guaranteed to seal properly the first time every time Your new American Standard faucet is designed to work only with the Speed Connect drain Heplful tips for removing your current drain can be found in the Troubleshooting section of these instructions To ensure that your installation proceeds smoothly please read these instructions carefully before you begin Recommended tools a THN Screwdriver Channel Locks Adjustable Wrench Tubing Cutter INSTALL SPOUT RST iins before beginning E Insert SPOUT 1 and CABLE CONNECTOR 14 through center hole making sure the SPOUT ESCUTCHEON 2 and SEAL WASHER 3 are properly seated g Assemble RUBBER WASHER 4 BRASS WASHER 5 and LOCKNUT 6 onto SPOUT 2 SHANK 7 from under side of sink Make sure SPOUT 1 is centered in the mounting hole and the slot in the BRASS WASHER 5 faces toward the rear of the sink m Tighten LOCKNUT 6 firmly Fig A JASMINE INSTALL VALVE BODY Place RUBBER RING 9 into DECK ADAPTER 10 Install LOCKNUT 41 and RUBBER WASHER
5. R M962533 YYYOA 3801 000 POP UP ROD 3841 000 IRIS 3841 M962531 YYYOA JASMINE 3801 SPOUT POP UP ROD SPOUT M962530 YYYOA Vy 066124 YYYOA 4 IRIS SPOUT KIT f DECORATIVE RING j 066124 YYYOA Ss DECORATIVE RING 909719 YYYOA j 066070 YYYOA SPOU i AERATOR ESCUTCHEON 030135 YYYOA 909718 YYYoa S__ SPOUT ESCUTCHEON Loe 066121 YYYOA SPOUT KIT 911836 0070A RUBBER RING 911862 0070A M962532 YYYOA RUBBER RING SPOUT KIT gt 033759 0070A W7 HOSE SEAL KIT M961733 0070A D 2 SPOUT MOUNTING KIT Moe 17329070A ein Gs 033757 0070A 028610 0070A whl f 9 CARTRIDGE MOUNTING KIT TEE MOUNTING KIT 033758 0050A TEE amp HOSE KIT SPOUT AND HOSE KITS BEFORE 12 06 030257 YYYOA ESCUTCHEON KIT mMm962544 YYYOA ASSEMBLY 030258 0070A VALVE SS W MOUNTING KIT M952430 0070A mg52425 vvyoa_ J CABLE ASSEMBLY DRAIN ASSEMBLY t M962457 007A M953006 0070A FLANGE TEE amp HOSE KIT p ASSEMBLY aR rE NUT CY M919660 0020A h 6 TAILPIECE M962430 0070A NOT INCLUDED f2 Tal CAM ASSEMBLY 066116 YYYOA WITH FAUCET Ga DRAIN STOPPER 066117 YYYOA 5 M913207 0070A 2 FLANGE KIT TAILPIECE INSERT M953450 YYYoA 066122 YYYO0A RAA COMPLETE LIFT ROD IRIS Replace the YYY with DRAIN ASSEMBLY o28618 vvvoa _ appropriate finish code LIFT ROD JASMINE 072574 0070A WHI
6. TE A919661 0020A ORDR 7 EXTENSION ROD BLK NICKEL BRASS ee BLACK SMITH POLISHED BRASS SATIN CHROME SATIN NICKEL M962458 0070A SATIN BRASS DRAIN MOUNTING KIT CHROME BRASS 070847 0070A CLIP A 43167 Rev 1 3 M961711 0070A TAILPIECE INSERT HOT LINE FOR HELP ZB For toll free information and answers to your questions call 070532 0040A 7 1 800 442 1902 TAILPIECE Weekdays 8 00 a m to 6 00 p m EST IN CANADA 1 800 387 0369 TORONTO 1 905 306 1093 Weekdays 8 00 a m to 7 00 p m EST POP UP DRAIN ASSEMBLY IN MEXICO 01 800 839 1 2 00 BEFORE 01 07 Product names listed herein are trademarks of American Standard Inc AS America Inc 2008
7. Turn valve to OFF position See handle instructions CLOTH with handle kit for removing handles DO NOT DO NOT CLEAN THE a Remove ADAPTER SCREW 1 and pull of ADAPTER 2 4 PRODUCT WITH SOAPS ACID POLISH ABRASIVES HARSH CLEANERS OR A CLOTH WITH A COARSE SURFACE Replace handle assembly See handle instructions 90 with handle kit for installing handles m ay a Remove SPRING CLIP 3 Lift STOP WASHER 4 turn 90 and replace Replace SPRING CLIP 3 ln 2 3 3 43167 Rev 1 3 Speed Connect Drain Troubleshooting Guide If sink does not hold water even though Stopper is in the down position e Follow CABLE ADJUSTMENT PROCEDURE If Stopper does not raise up fully or sink drains too slowly e Follow CABLE ADJUSTMENT PROCEDURE If you need to remove the ae ene e Follow STOPPER REMOVAL PROCEDURE If you would like the ability to remove your Stopper simply by lifting it out of the drain e Follow STOPPER INSTALLATION PROCEDURE for Unlocked mode CABLE ADJUSTMENT PROCEDURE Disconnect the Cable from the Drain by threading the Cable Connector 1 counter clockwise Fig A Look at the area on the Drain Body where the Cable was attached and locate the component labeled as Cam in the illustration Fig B Use a small screwdriver to rotate the Cam in the clockwise direction as far as it will go At this point the Stopper should be in the UP position Fig B C Push DOWN on the Lift Knob t
8. drain body from above SINK and tighten FLANGE 4 firmly 6 FLANGE GASKET AND POP UP KNOB m Check DRAIN FLANGE in SINK to ensure that WHITE FOAM GASKET 3 is fully compressed and not visible Fig A E POP UP KNOB 1 must be fully down Fig B WHITE FOAM GASKET NOT VISIBLE 43167 Rev 1 3 F ATTACH CABLE CONNECTOR Thread CABLE CONNECTOR 1 clockwise onto DRAIN BODY CONNECTION 2 and hand tighten Fig A Your new POP UP DRAIN installation is now complete Fig B Note Tailpeice on pop up drain is 1 1 4 0 D Fig B 8 CHECK OPERATION OF POP UP Operate LIFT KNOB 1 to verify that STOPPER 2 opens and closes Note If STOPPER 2 does not open and close properly then refer to the troubleshooting section of these instructions 9 MAKE WATER SUPPLY AND WASTE CONNECTIONS NOTE FLEXIBLE SUPPLIES OR BULL NOSE RISERS NOT INCLUDED AND MUST BE PURCHASED SEPARATELY Thread TEE BODY 4 to SPOUT SHANK 5 E Thread HOSE CONNECTOR 6 6A to VALVE CONNECTIONS 7 7A E Connect water supply to VALVE BODIES 1 1A with 1 2 IPS FLEXIBLE SUPPLIES 2 or 3 8 0 D BULL NOSE RISERS 3 Use adjustable wrench to tighten connections Do not over tighten Be careful not to kink copper supply when bending Use tubing cutter to cut to proper length Connect HOT water supply to inlet of left SHANK and COLD water supply to right SHANK using sealant appropriate connectors and COUPLING NUTS Connect 1
9. o make sure it is fully down Fig C Re attach the Cable to the Drain Body Connection 2 by threading the Cable Connector 1 clockwise onto the Drain Body Connection 2 and hand tighten Fig A STOPPER REMOVAL PROCEDURE Disconnect the Cable from the Drain by threading the Cable Connector 1 counter clockwise Fig A Look at the area on the Drain Body where the Cable was attached and locate the component labeled as Cam and Cam Cap in the illustration Fig B Use fingers or small screwdriver under either side of the Cam Cap to pry it out from the Drain Fig D Remove the Cam by pulling it straight out while wiggling gently to loosen the Rubber Seal Fig E The Stopper can now be removed by lifting it out of the Drain Fig F REMOVE CAM CAP 43167 Rev 1 3 STOPPER INSTALLATION PROCEDURE The Stopper can be installed two ways Locked Mode Stopper cannot be removed or Unlock Mode Stopper is removable Locked Mode Look at the Plastic Loop at the bottom of the Stopper and notice that the Loop is on one side of the Stopper Fig G To install the stopper in Locked mode insert the Stopper into the Drain so that the Plastic Loop is facing toward the rear of the Sink and the American Standard logo is facing front Rotate Stopper slightly if necessary so that the Stopper slides all the way down Fig G Re install the Cam into the Drain rotating the Cam if necessary to make sure it is fully
Download Pdf Manuals
Related Search