American Standard 2646 Indoor Furnishings User Manual
Contents
1. For 4114 Tanks A 14 856mm For all other Tanks A 12 305mm CLOSET BOLTS INSTALL CLOSET BOLTS 2 Install closet bolts in flange channel turn 90 and slide FLOOR into place 6 152 mm apart and parallel to wall NUT TAPERED im WASHER CLOSET Pa INSTALL WAX SEAL POSITION TOILET ON FLANGE Invert toilet on floor cushion to prevent damage and a Unplug floor waste opening and install toilet on closet flange so bolts project install wax ring evenly around waste flange horn with through mounting holes tapered end of ring facing toilet Apply a thin bead of b Loosely install retainer washers and nuts Side of washers marked THIS sealant around toilet base SIDE UP must face up Americam Toal Lhasa Sadosa i Standard Standard Stamdard Standard Cedelea Saniwares Product names listed herein are trademarks of American Standard Inc 730504 100 REV B American Standard Inc 2003 U S FUTURE R FO SAVE BOLT CAP CLOSET BOLT WASHER NUT INSTALL TOILET a Position toilet squarely to wall and with a rocking motion press bowl down fully on wax ring and flange Alternately tighten nuts until toilet is firmly seated on floor A CAUTION DO NOT OVERTIGHTEN NUTS OR BASE MAY BE DAMAGED b Install caps on washers If necessary cut bolt height to size before installing caps c Smooth off the bead of sealant around base Remove excess sealant For Tanks Bowls using Speed C2. Ww SEE STEP 9 HAND TIGHT ONLY T Diagram 1 LPA CARE AND CLEANING ADJUSTMENTS Adjust water level Water level should be adjusted to level indicated on tank by adjusting float cup See Step 11 for water level adjustment method If bowl fails to siphon an adjustment may be required with the lift chain Simply remove the bead chain from the retainment clip see Fig 10A and take up slack on the chain and reinsert on lift rod Make sure the chain is not too taught Turn on water supply Adjust water to desired level by squeezing water level adjustment clip and moving FLOAT CUP up or down along stainless steel link When cleaning your toilet wash it with mild soapy water rinse thoroughly with clear water and dry with a soft cloth Avoid detergents disinfectants or cleaning products in aerosol cans NEVER use abrasive scouring powders or abrasive pads on your toilet seat Some bathroom chemicals and cosmetics may damage the seat s finish A WARNING Do not use in tank cleaners Products containing chlorine calcium hypochlorite can seriously damage fittings in the tank This damage can cause leakage and property damage American Standard shall not be responsible or liable for any tank fitting damage caused by the use of cleaners containing chlorine calcium hypochlorite Repair parts are determined by toilet tank number which can be found marked inside tank REPAIR PARTS LIST NOTE XXX represents color or tri
3. legal rights You may have other statutory rights that vary from state to state or from province to province in which case this warranty does not affect such statutory rights For service under this warranty it is suggested that a claim be made through the contractor or dealer from or through whom the product was purchased or that a service request including a description of the product model and of the defect be sent to the following address In the United States In Canada In Mexico American Standard Inc American Standard Customer Service Manager P O Box 6820 2480 Stanfield Rd Ideal Standard S A de C V Piscataway New Jersey 08855 Mississauga Ontario Via Morelos 330 Attention Director of Consumer Affairs Canada L4Y 1S2 Col Santa Clara Ecatepec 55540 Edo Mexico For residents of the United States warranty information may also be Toll Free 800 387 0369 obtained by calling the following toll free number 800 442 1902 730504 100 REV B 4
4. per Step 13 AMERICAN STANDARD ONE YEAR LIMITED WARRANTY If inspection of this American Standard plumbing product within one year after its initial purchase confirms that it is defective in materials or workmanship American Standard will repair or at its option exchange the product for a similar model This warranty does not apply to local building code compliance Since local building codes vary considerably the purchaser of this product should check with a local building or plumbing contractor to insure local code compliance before installation This warranty shall be void if the product has been moved from its initial place of installation if it has been subjected to faulty maintenance abuse misuse accident or other damage if it was not installed in accordance with American Standard s instructions or if it has been modified in a manner inconsistent with the product as shipped by American Standard American Standard s option to repair or exchange the product under this warranty does not cover any labor or other costs of removal or installation nor shall American Standard be responsible for any other incidental or consequential damages attributable to a product defect or to the repair or exchange of a defective product all of which are expressly excluded from this warranty Some states or provinces do not allow the exclusion or limitation of implied warranties so this exclusion may not apply to you This warranty gives you specific
5. shank of valve does not apply to flanged tubing CAUTION DO NOT USE CONE WASHER WITH PLASTIC SUPPLY LINE VINYL BRAIDED CONNECTOR SPS tock NUT COUPLING NUT D gt 7 ST WATER V r Captive cone washers already included No additional washers needed For all other Tanks Bowls RUBBER RUBBER GASKET WASHER NUT INSTALL TANK a Install large rubber gasket over threaded outlet on bottom of tank and lower tank onto bowl so that tapered end of gasket fits evenly into bowl water inlet opening Insert tank mounting bolts and rubber washers from inside tank through mounting holes and secure with metal washers and nuts With tank parallel to wall alternately tighten nuts until tank is snugged down evenly against bowl surface A CAUTION DO NOT OVERTIGHTEN NUTS MORE THAN REQUIRED FOR A SNUG FIT With correct washers in place see Step Ya tighten COUPLING NUT 1 4 turn beyond hand tight DO NOT OVERTIGHTEN CAUTION Overtightening of LOCK NUT or COUPLING NUT could result in breakage and potential flooding 730504 100 REV B ARM REFILL NIPPLE TUBE F a CRITICAL LEVEL MARK ical MUST BI 1 ABOVE OVERFLOW PIPE FILL VALVE WATER LEVEL ADJUSTMENT CLIP LINK VALVE ADJUSTABLE BODY HEIGHT FLAPPER 7 SHANK WASHER LOCK NUT a THREADED SHANK CONE WASHER SA PARTS FOR WATER CONNECTION COUPLING NUT
6. INSTALLATION For These Two Piece Toilets INSTRUCTIONS Ravenna 2642 2648 2646 Agliakerce Cadet 2656 2798 2898 2998 3600 quarerce Reminiscence 2311 2011 FLUSHING SYSTEM Thank you for selecting American Standard the benchmark of fine quality for over 100 years To ensure this product is installed properly please read these instructions carefully before you begin Certain installations may require professional help Also be sure your installation conforms to local codes A CAUTION PRODUCT IS FRAGILE TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE NOTE Pictures may not exactly define contour of china and components RECOMMENDED TOOLS AND MATERIALS Putty Knife Regular Screwdriver Adjustable Wrench Sealant Tape Measure Hacksaw Wax Ring Gasket Flexible Supply Tube Closet Bolts Carpenters Level IE REMOVE OLD TOILET Close toilet supply valve and flush tank completely Towel or sponge remaining water from tank and bowl Disconnect and remove supply line NOTE f replacing valve first shut off main water supply Remove old mounting hardware remove toilet and plug floor waste opening to prevent escaping sewer gases Remove closet bolts from flange and clean away old wax putty etc from base area NOTE Mounting surface must be clean and level before new toilet is installed ROUGHING IN DIMENSIONS NOTE Distance from wall to closet flange centerline must be as listed below For 4110 Tanks A 10 254mm perils Chea FINISHED WALL
7. aster Inc TROUBLESHOOTING GUIDE PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION Does not flush a Water supply valve closed a Open valve and allow water to fill tank b Supply line blocked b Shut off water supply disconnect supply line and inspect all gaskets and washers Reassemble Also see Fluidmaster maintenance see step 13 Flush valve chain too loose or disconnected i Readjust chain length as required Sand or debris lodged in water control f Shut off water supply Remove cap and clean per Step 13 Poor or sluggish flush Bowl water level too low b Check that refill tube is connected to water control and inserted into tank overflow without being kinked or damaged Supply valve partly closed 4 Open supply valve fully Be sure that proper supply tube size is used Partially clogged trapway and or drain pipe and or vent a Remove obstruction Consult a plumber if necessary Supply pressure too low S Normal supply pressure must be at least 20 psi Toilet leaks Poor supply line connection 4 Review Step 9 of installation procedure Poor bowl to tank floor connection Review Step 4 through 7 of installation procedure Toilet does not shut off Flush valve chain too tight holding flush valve open s Readjust chain length as needed Review step 10 Flush valve seat and or flapper worn or deformed Replace flapper flush valve assembly as needed Sand or debris lodged in water control i Shut off water supply Remove cap and clean
8. ing because it s worn dirty or misaligned with tank ball or flapper replace with a new flapper IF FILL VALVE WON T TURN ON OR SHUT OFF or REFILL OF TANK WATER IS SLOW after valve has been in use for IMPORTANT Always e While holding a e Replace TOP by engaging some time Fluidmaster Model 242 Replacement Seal may be clear sand and rust from container over the lugs and rotating 1 8 turn needed system uncapped VALVE to clockwise MAKE CERTAIN P Make sure water supply is prevent splashing turn TIP IS TURNED TO THE oes E T off Remove valve TOP by water supply on and off a LOCKED POSITION lifting arm and rotating top few times Leave water VALVE MAY NOT TURN For troubleshooting information please contact and arm 1 8 turn supply off ON IF TOP IS NOT FULLY counterclockwise pressing TURNED TO THE LOCKED down slightly on cap POSITION Fluidmasterlnc 30800 Rancho Viejo Road GUARANTEE This Fluidmaster product is guaranteed to be free from defective materials and San Juan Capistrano CA 92675 workmanship for a period of one year Units returned to Fluidmaster will be replaced without charge 949 728 2000 800 631 2011 www fluidmaster com Always use quality Fluidmaster repair parts when maintaining your Fluidmaster products Fluidmaster shall not be responsible or liable for any damages caused by products used with Fluidmaster valves 2001 Fluidmaster Inc that were not manufactured by Fluidmaster Inc Registered trademark of Fluidm
9. m finish options Specify when ordering PART NO 047242 XXX0A DESCRIPTION TRIP LEVER TANK NUMBER 4111 Reminiscence 4096 Ravenna 4112 Cadet 4656 Cadet S 4114 Cadet 047192 XXX0A TRIP LEVER S 14110 Cadet S aN 730288 XXX0A TRIP LEVER 73851 7 XXX0A TRIP LEVER 738171 XXX0A RIGHT HAND TRIP LEVER 034783 XXX0A BOLT CAP KIT INCL TWO COVERS amp WASHERS 738565 400 0070A FLUIDMASTER 400A VALVE NINN 738565 401 0070A FLUIDMASTER 400A VALVE 738565 402 0070A FLUIDMASTER 400A VALVE 738565 404 0070A FLUIDMASTER 400A VALVE 738138 0070A FLUSH VALVE 738484 0070A FLUSH VALVE 738360 0070A FLUSH VALVE 738361 0070A FLUSH VALVE 730505 0070A COUPLING KIT BOWL TO TANK KIT 230 738159 0070A FLAPPER ASSEMBLY 738397 0070A FLAPPER ASSEMBLY 738358 0070A FLAPPER ASSEMBLY 738359 0070A FLAPPER ASSEMBLY 738565 418 0070A FLUIDMASTER 400A VALVE 730519 0070A COUPLING KIT BOWL TO TANK KIT 233 730504 100 REV B TROUBLESHOOTING IF FILL VALVE SHUTS OFF BUT CONTINUES TO LEAK SLOWLY repeat Step 13 IF FILL VALVE TURNS OFF AND ON DURING PERIODS OF NON USE it is a signal you are wasting water because LIFT ARM The end of the refill tube is inserted into overflow pipe below water level in tank Attach refill tube to overflow pipe using S clip provided The flush valve is leak
10. onnect System Tank mounting bolts pre installed RUBBER TANK MTG 7 GASKET BOLTS PRE INSTALLED WASHER NUT INSTALL TANK a Install large rubber gasket over threaded outlet on bottom of tank and lower tank onto bowl so that tapered end of gasket fits evenly into bowl water inlet opening and tank mounting bolts go through mounting holes Secure with metal washers and nuts With tank parallel to wall alternately tighten nuts until tank is snugged down evenly against bowl surface A CAUTION DO NOT OVERTIGHTEN NUTS MORE THAN REQUIRED FOR A SNUG FIT Before continuing determine the type of water supply connecation you have from the chart below and use the appropriate assembly parts required to properly reconnect the water supply DO NOT use plumber s putty to seal these fittings METAL COPPER FLARED TUBING LOCK NUT CONE WASHER METAL FLANGED METAL SPIRAL TUBING TUBING TES tock nut E Lock ut S EXISTING EXISTING WASHER CONE EXISTING WASHER COUPLING COUPLING NUT NUT WATER WATER SHUT OFF SHUT OFF Use existing Use existing spiral coupling nut cone washer and washer Fluidmaster cone washer may not seal completely on spiral type supply line COUPLING NUT WATER SHUT OFF These parts must be used as illustrated to insure water tight connection Use of existing coupling nut may result in water leakage Water supply tube or pipe must extend at least 1 2 inside threaded
Download Pdf Manuals
Related Search