American Audio XDM343 Musical Instrument User Manual
Contents
1. TALE Crea 1 POWER SWITCH 2 MASTER LEVEL PFL DISPLAY The upper display shows the level of the left and right master output The lower display shows the level of the channel currently being cued PFL LED on 3 GAIN CONTROL Used to set the level of the input signal 4 BASS MIDDLE TREBLE CONTROL Used to increase or decrease the LOW s MIDs and Hls of the input signal 5 PHONO LINE I MIC SWITCH Used to select the input to be sent to the individual channel Channel 1 and 2 can be switched phono line mic Channel 3 can either be switched line line mic or phono line mic The selector is on the rear panel 6 CHANNEL FADER Used to adjust the input level of each channel 7 PFL CUE BUTTONS Use the PFL CUE button to adjust the input level of each channel 8 BEAT INDICATOR CHANNEL CHANNEL 2 The LED lights up at every bass beat of the respective source As soon as the LEDs blink synchronously the speed of the two sources is synchronized 9 CROSSFADER Mixes the signals of channel 1 and channel 2 When the crossfader is set in the center position both channels can be heard at once 10 MIC 3 JACK You can connect microphones with 1 4 inch 6 8mm jack plug or XLR plug 11 TALKOVER BUTTON Press the talkover button when you want to use the microphone When the button is pressed all signals except the microphone level are decreased by 15dB In the OFF position all signals return to their original level When talkove2. LINE MIC switch 5 is set to MIC 1 American DJ AUDIO Los Angeles CA 90058 USA Specifications subject to change without notice XDM 343 User Instructions page 4 PROformer Series Americaa OF o AUDIO 28 MIC 2 JACK Connect your microphone with 1 4 inch 6 3mm jack plug here The signals can be controlled via CHANNEL 2 if the PHONO LINE MIC switch 5 is set to MIC 2 29 LINE 3 PHONO 3 SELECTOR Used to switch the CH 3 input jacks to line 3 or phono 3 Replacing the Crossfader Instructions for replacing the crossfader e Disconnect from main power supply e Remove the fader knob e Remove the two outer screws e Take the fader out and unplug the connection cable e Connect the new fader and replace back into mixer Technical Specifications model XDM 343 ee Microphone Line Frequency range S N ratio Talkover Tone control Treble 10Khz 12dB Middle 1 KHz 12dB Bass 100 Hz 12dB Headphone impedance 16 Ohms Power supply AC115 230V 50 60Hz 12 5 Wx 10 25 D x 4 262 x 320 x 102 mm Weight 8 lbs 3 5 kg American DJ AUDIO Los Angeles CA 90058 USA Specifications subject to change without notice XDM 343 User Instructions page 5
3. PHOformer Series Americaa OF o AUDIO User Instructions XDM 343 PREAMP MIXER om m a ae _ i a n E Thank you for purchasing this American DJ product The XDM 343 is ready to be used there is no assembly required Please read the following instructions before installing or using your new unit The XDM 343 has a 2 year limited warranty CAUTION Keep this device away from rain and moisture Safety Instructions Always plug in the power last Make sure that the Power switch is set to the OFF position before connecting other devices to the mixer Keep away from heaters and other heating sources If the device has been exposed to drastic temperature fluctuation e g after transportation do not switch on the mixer immediately The arising condensation of water might damage your device Leave the device switched off until it has reached room temperature Never put any liquids on the mixer or close to it Should any liquid enter the device disconnect from main power immediately Have the device be checked by a qualified service technician before operating again Any damage caused by liquid entering the device is not subject to warranty Never let the AC cord come in contact with other cables Handle the AC cord and all AC connections with particular care Make sure that the available voltage is not higher than stated on the AC voltage selector 25 Before the device is switched on all fader and
4. 4 inch 6 3mm Mic jacks 27 28 on the rear panel You can adjust the microphone volume using the CHANNEL faders Make sure that the respective PHONO LINE MIC switch is set to MIC e You can connect 2 record players using the PHONO 1 jacks 18 and PHONO 2 jacks 19 on the rear panel You can only control the record player signal after you switched the PHONO LINE MIC switches 5 to PHONO The signal is then controlled via the CH 1 and CH 2 faders 6 If you wish to connect a third record player switch the LINE 3 PHONO 3 SELECTOR 29 on the rear panel to PHONO 3 You can only control the record player signal after you switched the PHONO 3 LINE 3 LINE 4 MIC 3 switch 5 to PHONO 3 The signal is then controlled via the CHANNEL 3 fader 6 e Connect your tape recorder tuner sound effects CD player cassette deck or any other line signals to the AMP OUTjacks 18 19 amp 20 on the rear panel You can only control the line signals after switching the PHONO LINE MIC switches 5 to LINE The signal is then controlled via the CH 1 CH 2 and CH 3 faders 6 American DJ AUDIO Los Angeles CA 90058 USA Specifications subject to change without notice XDM 343 User Instructions page 2 PROformer Series Americaa OF o AUDIO Functions OW Q Aemerntcan DU AUD I ued wn i XDM PREAMP MEXER I PPL IHD ICAT F Eh EE E ee ee ee e ee e PRO amer Se ES am 2222 _ f e _
5. ing other devices to the mixer all units have to be switched off and the Master Control 17 set to min e Make sure that the available voltage is not higher than stated on the voltage selector 25 before connecting to power e In order to obtain the highest sound quality only use high quality American DJ Ameri Cable cables for connecting devices Make sure that the cables are properly fixed e Connect your amplifier to the OUT MASTER jacks 23 Make sure that the channels are set properly e For recording connect your tape recorder or cassette deck to the OUTPUT REC jacks 21 The REC OUT level will not be influenced by the Master Control 17 You can set the output level with the channel faders 6 the tone controls 4 and the GAIN control 3 e Connect your microphone to the Microphone Input 23 on the rear panel Make sure that the jacks are set properly See diagram on page 4 e Connect your record player s to the PHONO 1 jacks 16 and the PHONO 2 jacks 17 on the rear panel You can only control the record player signal after switching the PHONO LINE switches 2 to phono The signal is then controlled via the CH 1 and CH 2 faders 4 e The XDM 343 features three microphone inputs The Canon Mic 3 jack 10 on the front panel is for 1 4 6 3mm jack plugs and XLR plugs With the TALKOVER switch 1 1 you can attenuate all other signals without affecting the microphone volume The XDM 343 also features two more 1
6. r is ON the red L E D is lit NOTE The TALKOVER button only works with the microphone plugged into MIC 3 JACK American DJ AUDIO Los Angeles CA 90058 USA Specifications subject to change without notice XDM 343 User Instructions page 3 PROformer Series Americaa OF o AUDIO Functions Cont 12 CUE MIXING CONTROL Selects the channel for monitoring The monitor signal comes from Prefader This means it will not be affected by the channel faders You can monitor every channel individually and all possible combinations Connect your headphones to the HEADPHONES jack 14 Turn the CUE MIXING CONTROL to CUE and select the desired channels with the PFL switches 7 When you turn the CUE MIXING CONTROL to PGM PFL switches without function you can cue the output signal of the mixer If the CUE MIXING CONTROL is set to the center position you can cue both the channel signal you selected and the output signal With the CUE LEVEL control 13 you can adjust the phones volume without changing the output signal 13 CUE LEVEL CONTROL Adjusts the headphone output level 14 HEADPHONES JACK Use this jack to connect the headphones Headphones from 8 Ohms to 600 Ohms can be used 16 Ohms is recommended 15 BOOTH LEVEL CONTROL The XDM 348 features a DJ BOOTH monitor system Connect your monitor system with the BOOTH OUT jacks 22 on the rear panel 16 BALANCE CONTROL Used to adjust how much of the signal is sent to the left and
7. right MASTER OUT jack 23 17 MASTER CONTROL Adjusts the level of the master output Inputs and Outputs ACVOLTAGE SELECTOR l LINE 3 PHONO 3 115 230V MASTER BOOTH REC LINE g 3 9 O 2 Q Q 1 4 1 PHDNO 3 I OUTPUT CH 3 ICH 2 ICH 4 1 DO OOA 18 19 20 LINE PHONO INPUT JACKS Input jack for CH 1 CH 2 and CH 3 Connect turntables equipped with MM pickup cartridge to PHONO input CD players or Tape Decks should be connected to LINE input Line level musical instruments with stereo outputs such as Rhythm Machines or Samplers should also be connected to LINE inputs Channel 3 can be switched to 2 line inputs or line phono input by using the LINE 3 PHONO 3 selector 29 21 REC OUT To connect your record unit The REC OUT level is not influenced by the master control 22 BOOTH OUT Connect your monitor system here 23 MASTER OUT Parallel output of P A output Connect with the input of power amplifier 24 FUSE Fuseholder Only replace the fuse when the device is disconnected from main power supply Only replace with fuses of the same power and rating 25 AC VOLTAGE SELECTOR Make sure that the selector is properly set 26 GND Ground terminal Connect the ground lead of the turntable with this terminal This helps to reduce humming and pop noises 27 MIC JACK Connect your microphone with 1 4 inch 6 8mm jack plug here The signals can be controlled via CHANNEL 1 if the PHONO
8. volume controls should be set to 0 or minimum position Damages caused by manual modifications to the device or unauthorized operation by unqualified persons are not subject to warranty There are no user serviceable parts inside the mixer For maintenance and or service contact an authorized American DJ dealer American DJ AUDIO Los Angeles CA 90058 USA Specifications subject to change without notice XDM 343 User Instructions page 1 PROformer Series Americaa OF o AUDIO Operating Determinations When installing this mixer please make sure that the device is not exposed to extreme heat moisture or dust There should not be any cables lying around Doing so endangers you as well as others Do not operate the mixer in extremely hot more than 30 C 100 F or extremely cold less than 5 C 40 F surroundings Keep away from direct sunlight and heaters Operate the mixer only after becoming familiar with its functions Do not permit operation by persons not qualified for operating the mixer Most damages are the result of unprofessional operation Never use spray cleaners to clean the faders Never use solvents or abrasive detergents to clean the mixer It is recommended that you use a soft damp cloth Please consider that unauthorized modifications on the device are forbidden due to safety reasons Connections Refer to diagrams on pages 3 amp 4 e Make sure that the power switch 1 is set to OFF Before connect
Download Pdf Manuals
Related Search