Altinex MT106-101 Network Card User Manual
Contents
1. Keep this manual handy for future reference These safety instructions are to ensure the long life of your MT106 101 and to prevent fire and shock hazard Please read them carefully and heed all warnings 1 1 GENERAL Qualified ALTINEX service personnel or their authorized representatives must perform all service 1 2 INSTALLATION To prevent fire or shock do not expose this unit to rain or moisture Do not place the MT106 101 in direct sunlight near heaters or heat radiating appliances or near any liquid Exposure to direct sunlight smoke or steam can harm internal components Handle the MT106 101 carefully Dropping or jarring can damage the card Do not pull the cables that are attached to the MT106 101 Insert the card carefully into the slots of the Multi Tasker M without bending any edges When removing a card pull it halfway through to avoid damage to internal cables If an Expansion card is being removed please make sure that the Main card to which it is attached is also pulled out simultaneously 1 3 CLEANING Clean only the connector area with a dry cloth Never use strong detergents or solvents such as alcohol or thinner Do not use a wet cloth or water to clean the card Do not clean or touch any component or PCB 1 4 FCC CE NOTICE This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 22. this device must accept any interference received including interference that may cause operation undesired ZALTINEX Tel 714 390 2300 MULTI TASKER This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense Any changes or modifications to the unit not expressly approved by ALTINEX Inc could void the user s authority to operate the equipment Toll Free 1 800 ALTINEX FAA 714 390 3303 E mail solutions altinex com Web wv w altinex com ABOUT YOUR MT106 101 2 MT106 101 Scan Doubler Card The MT106 101 is a Scan Doubler Card designed for use with the Multi Tasker system When installed in a Multi Tasker enclosure this card allows the connection of an S Video or one of three Composite Video NTSC PAL sources to a data grade monitor or projector The 106 101 doubles the scan rate from 15 7 kHz to 31 5 kHz
3. 9 refer to the MT100 100 user s guide for explanation MULTI TASKER Example There is an MT106 101 in slot 2 of unit ID 3 View the current Horizontal Size and adjust the image to the center of the screen HSIZEC2U3 10 HSIZEC2U3 STATUS Current value 10 Feedback of current value 8 Adjust as required 13 VSIZEnCi Set Value This command sets the Vertical Size to an absolute value and makes the Vertical Size adjustment the active control Command Format VSIZEnCiUy n a value from 0 to 20 Default 19 Ci card ID i slot number Uy unit id i 0 to 9 refer to the MT100 100 user s guide for explanation Example There is an MT106 101 in slot 1 of unit ID 1 oet the Vertical Size to the value of 6 by sending the command VSIZE6C1U1 14 VSIZECi Status Adjust This command selects the Vertical Size adjustment and makes it the active control It also returns the status of the current Vertical Size As the active control it may be adjusted using the commands Command Format VSIZECiUy ID i slot number Uy unit id i 0109 refer to the MI 100 100 users guide for explanation Example There is 106 101 in slot 2 of unit ID View the current Vertical Size and adjust the vertical size for the best fit VSIZEC2U3 10 VSIZEC2U3 STATUS Current value 10 Feedback of current value 8 Adjust as required eC oo
4. following STATUS commands Toll Free 1 800 ALTINEX FAA 714 390 3303 E mail solutions altinex com Web www altinex com Value Value Value o 20 5 vPOS o 20 19 HSzE o 20 19 vsz o 2 19 terei o 2 10 rtsHarPy o 3 2 COLOR o 10 10 Hu 0o 10 10 Attempting to cycle past the minimum maximum values will have no effect on the attribute s value Any command other than or will reset the previous selection and the STATUS command will need to be reissued Example There is 106 101 in slot 4 of unit ID 2 current Horizontal Position is set to a value of 10 Use the and controls to find the best horizontal position Starting from 10 first increment the value to 12 Next decrement the value back down to 8 for the best picture HPOSC4U2 10 IE HPOSC4U2 STATUS Current value 10 Feedback of current value Increment twice to 12 Decrement 4 times to 8 HPOSC4U2 STATUS Current Value 8 Feedback of new value HPOSnCi Set Value This command sets the Horizontal Position to an absolute value It also makes the Horizontal Position adjustment the active control Command Format HPOSnCiUy n a value from 0 to 20 Default 5 ID i slot number Uy unit id i 0109 refer to the MT 100 100 user s guide
5. for explanation MULTI TASKER Example There is MI106 101 in slot 7 of unit ID 4 oet the Horizontal Position to the maximum value of 20 by sending the command HPOS20C7UA HPOSCi Status Adjust his command selects the Horizontal Position adjustment and makes it the active control It is also used to return the status of the current Horizontal Position As the active control it may be adjusted using the and commands Command Format HPOSCiUy Ci ID i slot number Uy unit id i 2 O to 9 refer to the MT100 100 user s guide for explanation Example There is an MT106 101 in slot 4 of unit ID 1 View the current Horizontal Position and adjust for the best image HPOSCAU 1 0 HPOSCAU1 STATUS command 10 Feedback of current value 8 Adjust as required VPOSnCi Set Value This command sets the Vertical Position to an absolute value and makes the Vertical Position adjustment the active control Command Format VPOSnCIUy n a value from 0 to 20 Default 19 Ci ID i slot number Uy unit id i 2 O to 9 refer to the MT100 100 user s guide for explanation Example There is an MT106 101 in slot 2 of unit ID 3 Set the Vertical Position to the value of 12 by sending the command VPOS12C2U3 10 VPOSCi Status Adjust ZALTINEX Tel 714 990 2300 Toll Free 1 B00 ALTINEX FAA 714 990 3303 E mail solutions altinex com Web
6. while converting the interlaced broadcast video type signal to a non interlaced VGA type signal The selection of an input source is accomplished by RS 232 control through the Multi Tasker enclosure A N presentation systems often require the use of monitors that are designed specifically to handle computer video signals The MT106 101 allows the integration of composite video or S Video into these systems The MT106 101 can also help to simplify systems that would otherwise require switching between video and RGB inputs on projector or large screen display Furthermore the MT106 101 improves the quality of a composite video signal resulting in a steadier image with higher definition The MT106 101 provides a number of features that can be controlled via RS 232 through the Multi Tasker Basic Enclosure These features include controls for horizontal and vertical positioning horizontal and vertical sizing black level color contrast and brightness The MT106 101 offers 3 composite video inputs on female BNC connectors and an S Video input on a standard 4 pin mini DIN connector The latter may be adapted to 2 BNC connectors using ALTINEX adapter cables The MT106 101 output is provided on a 15 pin HD female VGA type computer video connector This output may also be easily adapted to 5 BNC connectors for RGBHV using an ALTINEX adapter cable Using the MT104 101 8 in Video Switcher expansion cards up to 32 additional composite
7. wv w altinex com his command selects the Vertical Position adjustment and makes it the active control It also returns the status of the current Vertical Position As the active control it may be adjusted using the and commands Command Format VPOSCIUy Ci card ID i 2 slot number Uy unit id i 0 to 9 refer to the MT100 100 user s guide for explanation Example There is an MT106 101 in slot 2 of unit ID 3 View the current Vertical Position and adjust the image for the best vertical position VPOSC2U3 10 VPOSC2U3 STATUS Current value 10 Feedback of current value 8 Adjust as required 11 HSIZEnCi Set Value This command sets the Horizontal Size to an absolute value and makes the Horizontal Size adjustment the active control Command Format HSIZEnCiUy n a value from 0 to 20 Default 19 Ci card ID i slot number Uy unit id i 0 to 9 refer to the MT100 100 user s guide for explanation Example There is an MT106 101 in slot 2 of unit ID 3 oet the Horizontal Size to the value of 12 by sending the command HSIZE12C2U3 12 HSIZECi Status Adjust This command selects the Horizontal Size adjustment and makes it the active control It also returns the status of the current Horizontal Size As the active control it may be adjusted using the and commands Command Format HSIZECIUy Ci ID i slot number Uy unit id i 2 O to
8. 0 COLOR Color Adjust Status Command Format RDGKUI 21 HUE Set Hue value Gk group number k from 1 9 22 HUE Hue Adjust Status Ui unit number i from 0 9 23 HELP Display available commands member C1 C19 card 1 to 19 24 WR Group multiple cards 1 8 for MT100 101 or 1 4 for MT100 106 25 CLR Clear group configurations Example The cards in slots 1 2 and 19 are part of group 26 G neues greup Cale 5 in unit 1 Read the member data for group 5 27 RD Display group members of unit 1 by sending the command RDG5U1 The system will return feedback as follows ALTINEX Tel 714 990 2300 Toll Free 1 B00 ALTINEX FAA 714 990 3303 E mail solutions altinex com Web www altinex com TROUBLESHOOTING GUIDE 8 We have carefully tested and have found no problems in the supplied MT106 101 however we would like to offer suggestions for the following e 8 1 LED IS NOT LIT e 8 2 LED IS BLINKING RED e 8 3 NO DISPLAY 8 1 LED IS NOT LIT Cause 1 Solution Cause 2 Solution Cause 3 Solution 1 Solution 2 Card cage is not plugged in Plug the card cage in If the LED lights the problem is solved If the LED is still not ON see Cause 2 Card is not plugged in all the way Push the card in all the way If the LED is still not ON see Cause 3 Card cage slot has a problem Test the card in other slots of the card cage If the slot was damaged the card may work in other s
9. 6 101 EXP EXP 2 EXP 3 EXP 4 7j D 5 9 9 SIGNAL a DETECT POWER BNC IN 1 BNC IN 2 SCAN BNC IN 3 DOUBLER 15P HD OUT 4P MINI DIN ZALTINEX Tel 714 990 2300 Toll Free 1 800 ALTINES FAX 714 390 3203 E mail solutions altinex com Web w ww altinex com Tel 714 390 2300 INSTALLING YOUR MT106 101 Step 1 Slide the MT106 101 into an available slot in the Multi Tasker Basic Enclosure in order to connect to the bus Make sure that the MT106 101 Scan Doubler card fits into place Secure the card to the Multi Tasker by tightening the retainer screws located on the top and bottom of the MT106 101 Scan Doubler card Step 2 The LED on the card panel will turn red indicating that the card is in full operation A green LED indicates that an input signal is present An LED that is blinking red indicates that the card is experiencing a problem If the LED is blinking see the Troubleshooting Guide in section 10 Step 3 Connect an S Video cable or C Video cable coaxial cable from the video source to the input connectors of the MT106 101 Connect the output connector of the MT106 101 to the display device through a cable Step 4 Starting from the left identify the slot number where the MT106 101 card is plugged into the Enclosure Note that the slot number is required for RS 232 control OPERATION 7 7 1 RS 232 CONTROL When used in the Multi T
10. MULTI TASKER Mult Tasker MANUAL PART NUMBER 400 0097 004 SCAN DOUBLER CARD FOR MULTI TASKER USER S GUIDE ALTINEX Tel 714 990 2300 Toll Free 1 800 ALTIMEX FAX 714 990 3303 E mail Web www altinex com MULTI TASKER TABLE OF CONTENTS Page PRECAUTIONS SAFETY WARNINGS 2 m 2 1 2 INSTALLATION 2 ge 2 mens 2 ABOUT YOUR MT106 101 3 TECHNICAL SPECIFICATIONS 3 DESCRIPTION OF MT106 101 4 APPLICATION 5 INSTALLING YOUR MT106 101 7 COOPERATION sacre nde hue eG Nd PUNIRI 7 7 1 RS 232 7 7 2 DESCRIPTION OF COMMANDS 7 7 3 SUMMARY OF COMMANDS 13 TROUBLESHOOTING GUIDE 14 8 1 LEDS NOT asma tre MEME DU 14 8 2 LED IS BLINKING RED 14 3 0 NO DISPLAY 14 ALTINEX 15 9 1 LIMITED WARRANTY RETURN POLICY 5 9 2 CONTACT INFORMATION 15 ZALTINEX Tel 714 990 2300 Toll Free 1 B00 ALTINEX FAA 714 990 3303 E mail solutions altinex com Web wv w altinex com PRECAUTIONS SAFETY WARNINGS 1 Please read this manual carefully before using your MT106 101
11. OLOR2C4U2 11 ALTINEX Tel 714 990 2300 Toll Free 1 B00 ALTINEX FAA 714 990 3303 E mail solutions altinex com Web www altinex com Tel 714 390 2300 20 COLORCi Status Adjust The COLOR command with no value selects the Color adjustment and makes it the active control It is also used to return the status of the current Color level As the active control it may be adjusted using the and commands Command Format COLORCiUy Ci ID i slot number Uy unit id i 0 to 9 refer to the MT100 100 user s guide for explanation Example There is an MT106 101 in slot 2 of unit ID 3 View the current Color level and adjust the color for the best possible picture COLORC2U3 2 COLORC2US STATUS Current value 2 Feedback of current value amp Adjust as required 21 HUE Set Value This command sets the Hue to an absolute value It also makes the Hue adjustment the active control Command Format HUEnCiUy n a value from 0 10 Default 10 ID i slot number Uy unit id i 0 to 9 refer to the MT 100 100 user s guide for explanation Example An MT106 101 is in slot 4 of unit ID 2 Set the Hue to the value of 7 by sending the command HUE7C4U2 22 HUE Status Adjust This command selects the Hue adjustment and makes it the active control It is also used to return the value of the current Hue level As the active cont
12. asker Basic Enclosure the MT106 101 has many advanced remote control capabilities which are accessible through standard RS 232 communication The actual control may be accomplished through a computer control system or any other device capable of sending RS 232 commands 7 1 1 RS 232 INTERFACE RS 232 commands for the MT106 101 in a simple ASCII character format ZALTINEX MULTI TASKER 1 Square brackets are part of the command 2 Use uppercase letters for all commands After processing a command an OK or ER string will be returned as feedback if F is included at the end of a command string or if the unit ID is zero 7 2 DESCRIPTION OF COMMANDS Each command consists of three parts function card ID and unit ID Function Card Unit ID Example VERC3U2 VER Function C3 Card ID U2 Unit ID For Function see a detailed explanation under each command description The Card is an assigned value from 1 to 19 based on which slot the card is put in The Card ID 0 CO is used for the controller see user s guide for the MT100 100 Changing the position of a card will significantly affect the commands recorded on software definitions or a third party control system The Unit ID has a value from O to 9 The Unit ID 0 should be used for single unit operation If the Unit ID is set to O then each command can be used without Ui use command SETUO see user s guid
13. e for the MT100 100 Example VERC3 for unit ID zero VERCSUI for unit ID other than zero VERC3 equivalent to VERCS3UO VER This command displays the software version and card type for the Scan Doubler card Command Format VERCnUi Cn card ID No n slot from 1 to 19 Toll Free 1 800 ALTINEX FAA 714 390 3303 E mail solutions altinex com Web wv w altinex com Tel 714 390 2300 Ui Unit ID i from 0 to 9 refer to the MT100 100 user s guide for explanation Example If one Scan Doubler Card is in slot 2 of unit 3 Send the command VERC2US the Multi Tasker M Basic Enclosure will return the following MT106 101 690 0155 003 MT106 101 card type 690 0155 003 z software version C This command receives the status of the card Command Format CnUi Cn card ID n a slot from 1 to 19 1 8 for MT100 101 or 1 4 for MT100 106 Ui unit id i 0 to 9 refer to the MT100 100 user s guide for explanation Example If there is one MT106 101 card in slot 2 of unit 3 set for NTSC outputs sending the command C2U3 to the Multi Tasker will yield the following feedback INPUT 640x480 OUTPUT NTSC C02 INPUT 640x480 Input resolution OUTPUT NTSC Output mode C02 Card is in slot 2 there is no card in slot 2 of unit 3 sending the C2U3 command will not return any feedback from either card SIGCi The Signa
14. groups 7 3 SUMMARY OF COMMANDS 1 VER Receives software version TOMBE ee On dest 2 Ci Receives status of the card 3 SIG Signal present command Example 1 To clear group 1 send the CLRG1U1 4 CLR Resets card to defaults command This command clears the 5 ON Select Input Source members for the specified group only 6 Decrement 2 clear all groups of unit 1 send the selected commands CLRG U1 command 7 HPOS Setthe Horizontal Position 26 G G 8 HPOS Horiz Position Adjust Status This command is used to request group data 0 With the command the user can identify which 9 VPOS Setthe Vertical Position input or output of a particular group is on 10 VPOS Vert Position Adjust Status Command Format 11 HSIZE Set the Horizontal Size Gk group number k from 1 9 12 HSIZE Horizontal Size Adjust Status Ui unit number i from 0 9 13 VSIZE Set the Vertical Size Example 14 VSIZE Vertical Size Adjust Size In unit IDO if group 1 has DA Cards with outputs l 1 and 2 on while group 2 has SW Cards with 15 BRIG Set Brightness level Input 2 on 16 BRIG Brightness Adjust Status G1 will return feedback as ON12 G1UO 17 SHARP Set Sharpness level G2 will return feedback as ON2 G2UO 27 RD 18 SHARP Sharpness Adjust Status 19 COLOR Set Color value This command displays the members in each group 2
15. he Sharpness adjustment the active control Command Format SHARPnCiUy n avalue from 0 to 3 Default 2 ID i slot number Uy unit id i 0 to 9 refer to the MT100 100 user s guide for explanation Example There is an MT106 101 in slot 4 of unit ID 2 Set the Sharpness to the value of 2 by sending the command SHARP2C4U2 18 SHARPCi Status Adjust This command selects the Sharpness adjustment and makes it the active control It is also used to return the status of the current Sharpness level As the active control it may be adjusted using the and commands Command Format SHARPCiUy Ci ID i slot number Uy unit id i 0 to 9 refer to the MT100 100 user s guide for explanation Example There is an 106 101 in slot 2 of unit ID View the current Sharpness and adjust the sharpness for a clean clear image SHARPC2U3 2 SHARPC2U3 STATUS Current value 2 Feedback of current value 8 Adjust as required 19 COLORnCi COLOR command sets the Color to an absolute value It also makes the Color adjustment the active control Command Format COLORnCiUy n avalue from 0 to 10 Default 10 card ID i slot number Uy unit id i 0109 refer to the MI 100 100 users guide for explanation Example If there is MT106 101 in slot 4 of unit ID 2 the color may be set to a value of 2 by sending the command C
16. inputs can be connected internally to the MT106 101 and controlled via RS 232 control to the Multi Tasker enclosure MULTI TASKER TECHNICAL SPECIFICATIONS 3 FEATURES DESCRIPTION MT106 101 GENERAL n l Inputs Composite Video 3 BNC Female Connectors m 1 4 pin Mini DIN Internal Input Connector 1 10 pin IDC Outputs Output Connector 1 15 HD Female Compatibility Composite Video S Video NTSC PAL Table 1 MT106 101 General MECHANICAL MT106 101 Hequired 10 C to 35 C 90 non condensing Table 2 MT106 101 Mechanical ELECTRICAL 106 101 Input Video S Video Signals 00 to 1 5V 1 7 p p max terminated 75 Ohms Output Sync Signals Horizontal Vertical 22 Ohms Power from Power MT100 100 Consumption MT106 101 300 mA 1 9 watts Table 3 MT106 101 Electrical ZALTINEX Tel 714 990 2300 Toll Free 1 B00 ALTINEX FAA 714 990 3303 E mail solutions altinex com Web wv w altinex com MULTI TASKER DESCRIPTION OF MT106 101 4 RETAINER SCREW POWER SIGNAL LED S VIDEO INPUT 3 C VIDEO INPUTS VGA OUTPUT BOTTOM RETAINER SCREW ZALTINEX Tel 714 990 2300 Toll Free 1 B00 ALTINEX FAA 714 990 3303 E mail solutions altinex com Web wv w altinex com MULTI TASKER APPLICATION DIAGRAM 5 Application 1 Application 2 MULTI TASKER Application 2 Internal View of MT10
17. l Present command tests for the presence of a signal on the input After sending the command the feedback will be either 1 signifying a signal is present or 0 indicating no signal was detected Ci card number Example To check for the presence of an input signal on card 4 send the command SIGC4 and verify feedback of 1 or 0 ZALTINEX MULTI TASKER 4 CLR This command resets the card configuration to factory defaults Command Format CLRCi Ci card ID n a slot from 1 to 19 1 8 for MT100 101 or 1 4 for MT100 106 Example There is an MT106 101 in slot 4 of unit O All controls are set to various levels and the output is in PAL mode Sending the command CLRC4 will set the level controls to their default values and place the output in NTSC format 5 ON The ON command selects one of four possible input sources to connect to the output INPUT Number INPUT Signal n Name 0 1 SvVvido C Video 1 C Video 2 C Video 3 Command Format ONnCiUy n Ci card ID i slot number Uy unit id i 0 to 9 refer to the MT100 100 user s guide for explanation value from O to 3 Example Connect the S Video signal input on the MT106 101 located in slot 4 of unit ID 2 to the VGA output connector ONOC4U2 6 or These commands allow the user to increase or decrease the value of the selected attribute They must be used immediately following one of the
18. lots If other slots work and the LED lights the problem is the card cage slot The card cage may require service ALTINEX at 714 990 2300 If the other slots do not work and the LED is still not lit see Solution 2 Take any other known good card with an LED and verify that the slot used is good by seeing if the other cards LED lights in that slot If it lights then the original card may be the source of the problem Call ALTINEX at 714 990 2300 8 2 LED IS BLINKING RED Cause 1 Solution 1 The CPU on the card working properly is not Look at the card and verify that there is no damage If there is no damage see Solution 2 ZALTINEX Solution 2 Cause 2 Solution 1 Cause 3 Solution 1 Solution 2 Solution 3 MULTI TASKER Verify that all IC s are seated in their sockets If the LED is still blinking red see Cause 2 The card and its serial device are not communicating Turn the system OFF and then ON again If there is still an error see Cause 3 RS485 communication error Make sure that the card is pushed all the way into the slot If there is still an error see Solution 2 Turn the system OFF and then ON again If there is still an error see Solution 3 Call ALTINEX at 714 990 2300 8 3 NO DISPLAY Cause 1 Solution Cause 2 Solution Cause 3 Solution Cause 4 Solution The source has a problem Check the source and make sure that there i
19. o ALTINEX Tel 714 990 2300 Toll Free 1 B00 ALTINEX FAA 714 990 3303 E mail solutions altinex com Web www altinex com MULTI TASKER 15 BRIGnCi Set Value This command selects the Brightness adjustment and makes it the active control It also returns the status of the current Brightness level As the active control it may be adjusted using the and commands Command Format BRIGnCiUy n a value from 0 to 20 Default 10 card ID i slot number Uy unit id i 0109 refer to the MI 100 100 user s guide for explanation Example There is an MT106 101 in slot 4 of unit ID 2 Set the Brightness to the value of 2 by sending the command BRIG2C4U2 16 BRIGCi Status Adjust This command selects the Brightness adjustment and makes it the active control It is also used to return the value of the current Brightness level As the active control it may be adjusted using the and commands Command Format BRIGCIUy Ci ID i slot number Uy unit id i 0 to 9 refer to the MT100 100 user s guide for explanation Example There is an MT106 101 in slot 2 of unit ID 3 View the current Brightness and adjust the brightness for a good image BRIGC2U3 2 BRIGC2U3 STATUS Current value 2 Feedback of current value 8 Adjust as required 17 SHARPnCi Set Value This command sets the Sharpness to an absolute value It also makes t
20. rol it may be adjusted using the and commands ALTINEX 12 MULTI TASKER Command Format HUECiUy Ci ID i slot number Uy unit id i 0 to 9 refer to the MT100 100 user s guide for explanation Example There is an MT106 101 in slot 2 of unit ID 3 View the current Hue and set the hue for a good image HUEC2U3 2 HUEC2U3 STATUS Current value 2 Feedback of current value amp Adjust as required 23 HELP In MTSetup exe this command displays a list of the commands available for the 106 101 along with a brief description Command Format HELPCiUy Ci card ID i slot number Uy unit id i 0 to 9 refer to the 100 100 user s guide for explanation 24 WR This command groups multiple cards in the Enclosure Each unit contains a maximum of nine groups Command Format WRCn GKkUi Cn card ID No n slot from 1 to 19 1 8 for MT100 101 or 1 4 for MT100 106 Gk group number k from 1 9 Ui unit number i from 0 9 Example To group cards 1 2 and 3 as group 5 of unit 1 send the command WRC1C2C3G5U1 After executing this command cards 1 2 and 3 will be grouped together as group 5 of unit 1 Toll Free 1 800 ALTINEX FAA 714 390 3303 E mail solutions altinex com Web www altinex com MULTI TASKER 25 CLR C1C2C19 G5U1 This command clears the members for a single group or for all nine
21. s a signal present and all source connections are correct lf the source is working and there is still no display see Cause 2 The card output is not selected Select the card output See RS 232 accessible commands in Section 7 If no display is present see Cause 3 Cable connections are incorrect Make sure that cables are properly connected Also make sure that the continuity and wiring are good lf there is still no display present see Cause 4 The display has a problem Make sure the display has power and is turned ON f there is still no display please call at 714 990 2300 Tel 714 990 2300 Toll Free 1 B00 ALTINEX FAA 714 990 3303 E mail solutions altinex com Web www altinex com MULTI TASKER ALTINEX POLICY 9 9 1 LIMITED WARRANTY RETURN POLICY Please see the Altinex website at www altinex com for details on warranty and return policy 9 2 CONTACT INFORMATION ALTINEX INC 592 Apollo street Brea CA 92821 USA TEL 714 990 2300 TOLL FREE 1 800 ALTINEX WEB www altinex com E MAIL solutions altinex com ZALTINEX Tel 714 990 2300 Toll Free 1 B00 ALTINEX FAA 714 990 3303 E mail solutions altinex com Web wv w altinex com
Download Pdf Manuals
Related Search