Whirlpool W10385093A - SP Use & care guide
Contents
1. Dryer Operation Dryer will not run Door not closed completely START PAUSE button not pressed firmly or held long enough Household fuse is blown or circuit breaker has tripped Make sure the dryer door is closed completely Press and hold the START PAUSE button 2 5 seconds There may be 2 household fuses or circuit breakers for the dryer Check that both fuses are intact and tight or that both circuit breakers have not tripped Replace the fuses or reset the circuit breaker If the problem continues call an electrician Incorrect power supply Electric dryers require 240 volt power supply Check with a qualified electrician Wrong type of household fuse Use a time delay fuse Household fuse is blown or circuit The drum may be turning but you may not have heat Electric breaker has tripped dryers use 2 household fuses or circuit breakers Replace the fuses or reset the circuit breaker If the problem continues call an electrician Incorrect power supply Electric dryers require 240 volt power supply Check with a qualified electrician Supply line valve not open For gas dryers make sure that the valve on the gas supply line is open Unusual Noise Water pump on dryer is running The water pump on the dryer is used during the Steam function If the dryer has just been installed or unused for an extended period the pump may be louder and run longer This is normal Dryer hasn t been used in a while This is no2. gt Whirlpool Use amp Care Guide Guide d utilisation et d entretien ELECTRONIC DRYER SECHEUSE ELECTRONIQUE Para obtener acceso al Manual de uso y cuidado en espa ol o para obtener informaci n adicional acerca de su producto visite www whirlpool com If you have any problems or questions visit us at www whirlpool com Pour tout probleme ou question consulter www whirlpoolappliances ca W10385092A W10385093A SP ELECTRONIC DRYER S CHEUSE LECTRONIQUE TABLE OF CONTENTS Table des Mati res DRYER SAFE TV scans dl 2 S CURIT DE LA S CHEUSE sioiias 19 ACCESSORIES Ss usina anta ib 4 ACCESSOIRES Sudan 21 CHECK YOUR VENT SYSTEM FOR GOOD AIR FLOW seeeceseeseeesesseeees 5 VERIFICATION D UNE CIRCULATION D AIR ADEQUATE CONTROL PANEL AND FEATURES res 6 POUR LE SYST ME D VACUATION 22 CYCLE STATUS INDICATORS rrrrrerrrrreeererrnernes 7 TABLEAU DE COMMANDE ET 66 5 23 CYCLE GUIDES diia 8 GUIDE DES PROGRAMMES nn ns cia 26 USING YOUR 10 UTILISATION DE LA SECHEUSE 28 ADDITIONAL FEATURES 0coccccncccinnncninnnccnnnnnnnnnnananonocannnaconananancnccnnnss 12 T MOINS LUMINEUX DE PROGRAMME ocoococccnonccnrnccnrnnnonnrnonornonornnoos 30 DRYER 13 CARACT RISTIQUES SUPPL MENTAIRES se 31 TROUBLESHOOTING serre 15 ENTRETIEN DE LA S CHEUSE 32 WARRANTY annee 18 DEP
3. Dryness Level is for use with Auto Cycles only Wrinkle Shield Option If you will be unable to remove a load immediately press the WRINKLE SHIELD button to add 90 minutes of periodic tumbling to help reduce wrinkling CYCLE SIGNAL Use this button to turn the signal indicating the end of a drying cycle on or off CYCLE STATUS INDICATORS Remaining Control Lock If the dryer is running Press and hold the Cycle Signal button for 3 seconds to lock the controls of the dryer and Cycle avoid an accidental change in cycle options Signal or settings during a drying cycle Press and hold again for 3 seconds to unlock To enable the Control Lock feature if the dryer is off it is not necessary to press POWER before activating the Control Lock feature press and hold for 3 seconds to lock unlock controls O Steam O Control Lock FSS OS 5 Sensing Wet Damp Cool Done Wrinkle Down Shield Steam model shown The Cycle Status indicators show the progress of a cycle Sensing The Sensing indicator will light during Auto Cycles to indicate that the moisture sensor on the dryer is operating This indicator will not light during Manual Cycles or options such as Wrinkle Shield Wet The load is still wet and or the cycle just started In the Enhanced Touch Up or the Quick Refresh Steam Cycles on some models the Wet indicator comes on after the water has been sprayed into the dru
4. Serial number number label located on the product Purchase date 18 NOTES REMARQUES 39 ASSISTANCE OR SERVICE Before calling for assistance or service please check Troubleshooting or visit www whirlpool com help It may save you the cost of a service call If you still need help follow the instructions below When calling please know the purchase date and the complete model and serial number of your appliance This information will help us to better respond to your request If you need replacement parts or to order accessories We recommend that you use only FSP Factory Specified Parts These parts will fit right and work right because they are made with the same precision used to build every new WHIRLPOOL appliance To locate FSP replacement parts assistance in your area or accessories Whirlpool Corporation Customer eXperience Center Whirlpool Canada LP 1 800 253 1301 www whirlpool com Customer eXperience Centre 1 800 442 9991 Accessories a tios ea www whirlpool com accessories or call your nearest designated service center or refer to your Yellow Pages telephone directory Our consultants provide assistance with In the U S A and Canada m Use and maintenance procedures Accessory and repair parts sales Referrals to local dealers repair parts distributors and service companies Whirlpool designated service technicians are trained to fulfill the product warranty and provide af
5. all models 5 Adjust cycle settings if desired More A Lol O Steam Time O Control Lock e a Less Time Sensing Wet Damp Cool Done Wrinkle O High Down Shield o Cycle O More Signal O Ex O Normal O Air Dry O Less press and hold for 3 seconds to lock unlock controls ature Dryness Wrinkle Shield Steam model shown for auto cycles 90 min You may adjust different settings depending on whether you have selected an Auto Cycle Manual Cycle or Steam Cycle on some models See the Cycle Guide for detailed information NOTE Not all options and settings are available with all cycles Not all cycles are on all models Auto Cycles You can select a different dryness level depending on your load by pressing the button for More Normal or Less Selecting More Normal or Less automatically adjusts the dryness level at which the dryer will shut off Once a dryness level is set it cannot be changed without stopping the cycle Automatic cycles give the best drying in the shortest time Drying time varies based on fabric type load size and dryness setting Manual Cycles When you select a Manual Cycle the default time appears in the display More Use the More Time A and Less Time Y buttons to increase or decrease the time Less in 1 minute increments Press and hold to change the time in 5 minute increments The default temperature may be changed by pressing the Temperature
6. are known to collapse be easily crushed and trap lint These conditions will obstruct clothes dryer airflow and increase the risk of fire To reduce the risk of severe injury or death follow all installation instructions Save these instructions State of California Proposition 65 Warnings WARNING This product contains one or more chemicals known to the State of California to cause cancer WARNING This product contains one or more chemicals known to the State of California to cause birth defects or other reproductive harm In the State of Massachusetts the following installation instructions apply Installations and repairs must be performed by a qualified or licensed contractor plumber or gasfitter qualified or licensed by the State of Massachusetts If using a ball valve it shall be a T handle type A flexible gas connector when used must not exceed 3 feet WARNING For your safety the information in this manual must be followed to minimize the risk of fire or explosion or to prevent property damage personal injury or death Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance WHAT DO IF YOU SMELL GAS e Do not try to light any appliance e Do not touch any electrical switch do not use any phone in your building e Clear the room building or area of all occupants e Immediately call your gas supplier from a neighbor s phone
7. button until the desired dry temperature is lit A Sensing Wet You may also adjust the time or temperature on a manual cycle at any time while the cycle is running Steam Cycles on some models Steam cycles add an extra boost of steam to help reduce odors and loosen wrinkles Quick Refresh Use to reduce odors and light wrinkles from small loads of 3 4 items Enhanced Touch Up Use to reduce wrinkles including from loads left in the dryer too long 6 Press and hold START PAUSE to begin cycle START PAUSE Press and Hold to START Press and hold the START PAUSE button to begin the cycle T Remove garments promptly after cycle is finished LI O Steam Li O Control Lock SS OO Sensing Wet Damp Cool Done Wrinkle Down Shield O More O Normal O Less Steam model shown Promptly remove garments after cycle has pd completed to reduce wrinkling If you will be 20 min unable to remove the load promptly select the Wrinkle Shield option before pressing START PAUSE to add up to 90 minutes of periodic tumbling after the end of the drying cycle Changing the Auto Cycle settings to increase drying time If all your loads on all Auto Cycles are consistently not as dry as you would like you may change the default settings to increase the default dryness level Your automatic drying settings can be adjusted to adapt to different installations environmental conditions or personal preference
8. chips or other damage to the finish of your major appliance unless such damage results from defects in materials or workmanship and is reported to Whirlpool within 30 days from the date of purchase 6 Pick up and delivery This major appliance is intended to be repaired in your home 7 Repairs to parts or systems resulting from unauthorized modifications made to the appliance 8 Expenses for travel and transportation for product service if your major appliance is located in a remote area where service by an authorized Whirlpool servicer is not available 9 The removal and reinstallation of your major appliance if it is installed in an inaccessible location or is not installed in accordance with Whirlpool s published installation instructions 10 Replacement parts or repair labor on major appliances with original model serial numbers that have been removed altered or cannot be easily determined DISCLAIMER OF IMPLIED WARRANTIES IMPLIED WARRANTIES INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW Some states and provinces do not allow limitations on the duration of implied warranties of merchantability or fitness so this limitation may not apply to you This warranty gives you specific legal rights and you also may have other rights that vary from state to state or province to province LIMITATION OF REMEDIES EXCLUSION
9. flooding due to a water pressure surge while you are away Moving Care For power supply cord connected dryers Unplug the power supply cord Gas models only Close shut off valve in gas supply line Gas models only Disconnect gas supply line pipe and remove fittings attached to dryer pipe Gas models only Cap the open fuel supply line Steam models only Shut off water faucet Disconnect the water inlet hose from faucet then drain the hose Transport hose separately Make sure leveling legs are secure in dryer base Use tape to secure dryer door AWARNING y Electrical Shock Hazard Disconnect power before servicing Replace all parts and panels before operating Failure to do so can result in death or electrical shock For direct wired dryers 1 Disconnect power 2 Disconnect wiring 3 Steam models only Shut off water faucet 4 Steam models only Disconnect the water inlet hose from faucet then drain the hose Transport hose separately 5 Make sure leveling legs are secure in dryer base 6 Use tape to secure dryer door Reinstalling the Dryer Follow the Installation Instructions to locate level and connect the dryer 13 WARNING AWARNING Electrical Shock Hazard Electrical Shock Hazard Electrically ground this appliance Disconnect power before servicing Do not use an extension cord Replace all parts and panels before operating Failure to do so
10. is not recommended with Steam Cycles The Enhanced Touch Up Cycle is best for smoothing out It may cause temporary staining on clothes wrinkles from clothes that have been left in the dryer too It is not recommended to use Steam Cycles for items that long For best results do not overload the dryer have been starched Wash any starched or new garments prior to using a Steam Cycle CONTROL PANEL AND FEATURES Not all features and cycles are available on all models Steam models ji START PAUSE Press and Hold to START Manuale AN Steam Cyc ee 25 TIMED DRY DRY pE CK REFRES REFRESH NHANCED TOUCH UP Non steam models ECO NORMAL HEAVY DUTY START PAUSE Auto Cycles Press and Hold to START Manual Cycles TOUCH UP SMALL LOAD TIMED DRY 0 POWER BUTTON Press to turn the dryer on and off Press to stop cancel a cycle at any time 9 CYCLE CONTROL KNOB Use your dryer s Cycle Control knob to select a cycle for your laundry load See Cycle Guide for detailed descriptions of cycles O START PAUSE BUTTON Press and hold to start a cycle or press once while a cycle is in process to pause it O MORE TIME LESS TIME for MANUAL CYCLES Use these buttons with Manual Cycles to increase or decrease the length of a Manual Cycle O LED DISPLAY AND SETTINGS BUTTONS When you select a cycle its default settings will light up and the Estimated Time Remaining will be displayed Use the buttons alo
11. not hang over the Lint should be removed every 2 years or more often edges or between drying rack grille depending on dryer usage Cleaning should be done Close the door by a qualified appliance servicer Select a Timed Dry Air Dry or Low Temperature cycle From the Exhaust Vent Items containing foam rubber or plastic must be dried Lint should be removed every 2 years or more often on a clothesline or by using the Air Dry setting depending on dryer usage When the cycle is selected the Estimated Time Remaining display shows the default time You can change the actual time in the cycle by increasing or decreasing the cycle time 7 Start the dryer NOTE Check the lint screen and remove any lint accumulated from items dried on the drying rack after the cycle is finished 12 CLEANING THE LINT SCREEN Every load cleaning The lint screen is located in the door opening of the dryer Be sure to clean the lint screen after each load A screen blocked by lint can increase drying time To clean 1 Pull the lint screen straight up Roll lint off the screen with your fingers Do not rinse or wash screen to remove lint Wet lint is hard to remove 2 Push the lint screen firmly back into place IMPORTANT Do not run the dryer with the lint screen loose damaged blocked or missing Doing so can cause overheating and damage to both the dryer and fabrics E If lint falls off the s
12. synthetic garments NOTE Refer to garment care label instructions Dry clean only garments are not recommended The dryer was overloaded Dry smaller loads that can tumble freely When using the Quick Refresh cycle on steam models select the correct number of garments 1 9 Results may also vary depending on fabric type This cycle is best for reducing wrinkles and odors from loads consisting of wrinkle free cotton cotton polyester blends common knits and synthetics Loads are wrinkled For steam cycles the water is not Make sure water is connected to the dryer Check that water Steam models only properly connected with the dryer inlet hose is connected to both the faucet and dryer s water inlet valve Check that the water supply is turned on 16 First try the solutions suggested here or visit our website at www whirlpool com help for assistance and to possibly avoid a service call If you experience Possible Causes Dryer Results cont Recent painting staining or varnishing in the area where your dryer is located For steam cycles the water is not properly connected with the dryer Odors are left in garments after wearing Load too hot Dryer Displaying Code Message PF power failure L2 Diagnostic Code low or no line voltage condition home power supply keeping the dryer s heater from turning on AF low airflow condition The lint screen or vent is clogged the ve
13. used with Auto Cycles To use the drying rack IMPORTANT Do not remove the lint screen 1 Open dryer door Explosion Hazard Keep flammable materials and vapors such as gasoline away from dryer Place dryer at least 18 inches 460 mm above the floor for a garage installation Failure to do so can result in death explosion or fire CLEANING THE DRYER INTERIOR To clean dryer drum Use a mild hand dish detergent mixed at a low 2 Align the two hooks on the front of the drying rack with concentration with very warm water and rub with the holes in the dryer door opening and press down fully a soft cloth into holes Rest the rear support on the dryer back ledge Rinse well with a wet sponge or towel Tumble a load of clean clothes or towels to dry drum OR Use a microfiber cloth and hot water in a spray bottle to clean the drum and a second microfiber towel to dry NOTE Garments that contain unstable dyes such as denim blue jeans or brightly colored cotton items may discolor the rear of the dryer interior These stains are not harmful to your dryer and will not stain future loads of clothes Dry unstable dye items inside out to avoid transfer of dye around items for air to circulate The drying rack does REMOVING ACCUMULATED LINT not move but the drum will rotate be sure to leave From Inside the Dryer Cabinet adequate clearance between items and the inside of the dryer drum Make sure items do
14. ANNAGE nai e dae ttt 34 ASSISTANCE OR SERVICE ccceccecceccecceccucceccecceccuceucenceuce Back Cover GARAN TE a 38 ASSISTANCE OU SERVICE viii aia Couverture arri re DRYER SAFETY Your safety and the safety of others are very important We have provided many important safety messages in this manual and on your appliance Always read and obey all safety messages This is the safety alert symbol This symbol alerts you to potential hazards that can kill or hurt you and others All safety messages will follow the safety alert symbol and either the word DANGER or WARNING These words mean You can be killed or seriously injured if you don t immediately ADANGER follow instructions You can be killed or seriously injured if you don t follow A WARNING instructions All safety messages will tell you what the potential hazard is tell you how to reduce the chance of injury and tell you what can happen if the instructions are not followed A WARNING Risk of Fire Clothes dryer installation must be performed by a qualified installer Install the clothes dryer according to the manufacturer s instructions and local codes Do not install a clothes dryer with flexible plastic venting materials or flexible metal foil type duct If flexible metal duct is installed it must be of a specific type identified by the appliance manufacturer as suitable for use with clothes dryers Flexible venting materials
15. Follow the gas supplier s instructions e If you cannot reach your gas supplier call the fire department Installation and service must be performed by a qualified installer service agency or the gas supplier WARNING Gas leaks cannot always be detected by smell Gas suppliers recommend that you use a gas detector approved by UL or CSA For more information contact your gas supplier If a gas leak is detected follow the What to do if you smell gas instructions IMPORTANT The gas installation must conform with local codes or in the absence of local codes with the National Fuel Gas Code ANSI Z223 1 NFPA 54 The dryer must be electrically grounded in accordance with local codes or in the absence of local codes with the National Electrical Code ANSI NFPA 70 IMPORTANT SAFETY INSTRUCTIONS WARNING To reduce the risk of fire electric shock or injury to persons when using the dryer follow basic precautions including the following Read all instructions before using the dryer Do not repair or replace any part of the dryer or attempt Do not place items exposed to cooking oils in your dryer any servicing unless specifically recommended in this Items contaminated with cooking oils may contribute to Use and Care Guide or in published user repair a chemical reaction that could cause a load to catch fire instructions that you understand and have the skills to carry out Do not use fabric softeners or products to eliminat
16. OF INCIDENTAL AND CONSEQUENTIAL DAMAGES YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN WHIRLPOOL SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES Some states and provinces do not allow the exclusion or limitation of incidental or consequential damages so these limitations and exclusions may not apply to you This warranty gives you specific legal rights and you also may have other rights that vary from state to state or province to province If outside the 50 United States and Canada contact your authorized Whirlpool dealer to determine if another warranty applies If you think you need repair service first see the Troubleshooting section of the Use amp Care Guide If you are unable to resolve the problem after checking Troubleshooting additional help can be found by checking the Assistance or Service section or by calling Whirlpool In the U S A call 1 800 253 1301 In Canada call 1 800 807 6777 7 08 Keep this book and your sales slip together for future reference You must provide proof of purchase or installation Dealer name date for in warranty service Address Write down the following information about your major appliance Phone number to better help you obtain assistance or service if you ever need it You will need to know your complete model number and serial Model number number You can find this information on the model and serial
17. Parts and repair labor to correct defects in materials or workmanship that existed when this major appliance was purchased Service must be provided by a Whirlpool designated service company YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN This limited warranty is valid only in the United States or Canada and applies only when the major appliance is used in the country in which it was purchased Proof of original purchase date is required to obtain service under this limited warranty ITEMS EXCLUDED FROM WARRANTY This limited warranty does not cover 1 Replacement parts or repair labor if this major appliance is used for other than normal single family household use or when it is used in a manner that is inconsistent to published user or operator instructions and or installation instructions 2 Service calls to correct the installation of your major appliance to instruct you on how to use your major appliance to replace or repair house fuses or to correct house wiring or plumbing 3 Service calls to repair or replace appliance light bulbs air filters or water filters Consumable parts are excluded from warranty coverage 4 Damage resulting from accident alteration misuse abuse fire flood acts of God improper installation installation not in accordance with electrical or plumbing codes or use of products not approved by Whirlpool 5 Cosmetic damage including scratches dents
18. This change is retained and will affect all of your Automatic cycles not just the current cycle load There are 3 drying settings which are displayed using the time display 1 Factory preset dryness level 2 Slightly drier clothes 15 more drying time 3 Much drier clothes 30 more drying time To change the drying settings NOTE The settings cannot be changed while the dryer is running or paused The dryer must be in standby mode the power button is off or only the DONE indicator lit to adjust the default settings 1 Before starting a cycle press and hold the TEMP button for 6 seconds 2 Press the TEMP button to select the dryness level shown in the time display 1 2 or 3 3 Press START PAUSE to save the new dryness level setting 11 ADDITIONAL FEATURES DRYER CARE USING THE DRYING RACK CLEANING THE DRYER LOCATION To obtain a drying rack for your dryer follow the instructions Keep dryer area clear and free from items that would included in your dryer drum Remove and discard any block the air flow for proper dryer operation This includes packing material before use clearing piles of laundry in front of the dryer Use the Drying Rack for items that you do not want to tumble dry such as sweaters and tennis shoes When you use the drying rack the drum continues to turn but the rack remains stationary AWAR N l N G The drying rack is intended for use with the Timed Dry cycles only The drying rack cannot be
19. ad may not be contacting Level the dryer See Installation Instructions All four dryer the sensor strips on Auto Cycles feet should be in firm contact with the floor Clothes are coming out of the Under certain environmental or installation conditions you Quick Refresh cycle on some may experience underdrying Select the Enhanced Touch Up models with damp or wet spots cycle on some models to finish drying The auto cycle is ending early Change the dryness level setting on Auto Cycles Increasing or decreasing the dryness level will change the amount of drying time in a cycle If loads are consistently ending too early see also Changing the Auto Cycle settings to increase drying time Lint on load Lint screen is clogged with lint Clean lint screen before each load Stains on load Improper use of dryer sheets Add dryer sheets at the beginning of the cycle Dryer sheets added to a partially dried load can stain your garments Do not use dryer sheets with steam cycles Stains on drum Loose dyes in clothes Drum stains are caused by dyes in clothing usually blue jeans These will not transfer to other clothing Loads are wrinkled The load was not removed from On steam models select Enhanced Touch Up Cycle to tumble dryer at the end of the cycle the load with water and heat This cycle is best for smoothing out wrinkles and reducing odors from loads consisting of wrinkle free cotton cotton polyester blends common knits and
20. can result in death or electrical shock CHANGING THE DRUM LIGHT The dryer light automatically turns on inside the dryer drum Failure to follow these instructions can result in death fire or electrical shock SPECIAL INSTRUCTIONS FOR STEAM MODELS when you open the door Water Inlet Hose To change the drum light Replace inlet hose and hose screen after 5 years of use to reduce the risk of hose failure Periodically inspect and pee replace inlet hose if bulges kinks cuts wear or leaks 2 a the ial aoe rae eae ulb cover on the back wall of the dryer are found f Wh jaci inletti cie di Remove the screw located in the lower PEAR PAS A right corner of the cover Remove the of replacement cover To Winterize the Dryer Turn bulb counterclockwise Replace the bulb with a 10 watt appliance bulb only Replace the cover and secure with the screw Plug in dryer or reconnect power 1 Unplug dryer or disconnect power 2 Shut off water faucet 3 Disconnect water inlet hose from faucet and drain To Use the Dryer Again 1 Flush water pipes Reconnect water inlet hose to faucet Turn on water faucet 2 Plug in dryer or reconnect power as described in the Installation Instructions 14 TROUBLESHOOTING First try the solutions suggested here or vis it our website at www whirlpool com help for assistance and to possibly avoid a service call If you experience Possible Causes po Solution O O O
21. cessories In Canada call provides a convenient working 1 800 807 6777 or visit us at www whirlpoolparts ca and storage area 15 Pedestal Color matched pedestals raise the washer and dryer to a more comfortable working height The large drawer provides convenient storage Available in matching colors Stack Kit If space is at a premium the stack kit allows the dryer to be installed on top of the washer CHECK YOUR VENT SYSTEM FOR GOOD AIR FLOW A WARNING Maintain good air flow by Cleaning your lint screen before each load Replace plastic or foil vent material with 4 102 mm diameter heavy rigid vent material Use the shortest length of vent possible Use a heavy metal vent Use no more than four 90 elbows in a vent system Do not use a plastic vent each bend and curve reduces air flow Fire Hazard D I foil o not use a metal foil vent Good Better Failure to follow these instructions can result in death or fire Good air flow Along with heat dryers require good air flow to efficiently dry laundry Proper venting will reduce your drying times and improve your energy savings See Installation nstuctions Remove lint and debris from the exhaust hood The venting system attached to the dryer plays a big role in Remove lint from the entire length of the vent system good air flow beige at least every 2 years When cleaning is complete be Service calls ca
22. creen into the dryer during removal check the exhaust hood and remove the lint See Venting Requirements As needed cleaning Laundry detergent and fabric softener residue can build up on the lint screen This buildup can cause longer drying times for your clothes or cause the dryer to stop before your load is completely dry The screen is probably clogged if lint falls off while the screen is in the dryer Clean the lint screen with a nylon brush every 6 months or more frequently if it becomes clogged due to a residue buildup To wash 1 Roll lint off the screen with your fingers 2 Wet both sides of lint screen with hot water 3 Wet a nylon brush with hot water and liquid detergent Scrub lint screen with the brush to remove residue buildup 4 Rinse screen with hot water 5 Thoroughly dry lint screen with a clean towel Reinstall screen in dryer NON USE STORAGE AND MOVING CARE Install and store your dryer where it will not freeze Because some water may stay in the hose freezing can damage your dryer If storing or moving your dryer during freezing weather winterize it Non Use or Storage Care Operate your dryer only when you are at home If you will be on vacation or not using your dryer for an extended period of time you should Unplug dryer or disconnect power Clean lint screen See Cleaning the Lint Screen Turn off the water supply to the dryer This helps to avoid unintended
23. d is properly installed Refer to Installation Instructions for details Select a Manual Cycle with heat and restart the dryer If the message persists consult a qualified electrician The dryer will continue to run when this diagnostic code is present Press any key to clear the code from the display and return to the estimated time remaining Try the following e Clean lint screen e Check to see if the vent run from the dryer to the wall is crushed or kinked e Confirm the vent run from the dryer to the wall is free of lint and debris Confirm the exterior vent exhaust hood is free of lint and debris Confirm your vent system falls within the recommended run length and number of elbows for the type of vent you are using Refer to Plan Vent System in the Installaton Instructions for details Select a Manual Cycle with heat and restart the dryer If the message persists have your entire home venting run cleaned If a code beginning with an F appears in the display Alternating between F and E the dryer control has detected a problem that requires service Call for service 17 WHIRLPOOL CORPORATION LAUNDRY WARRANTY LIMITED WARRANTY For one year from the date of purchase when this major appliance is operated and maintained according to instructions attached to or furnished with the product Whirlpool Corporation or Whirlpool Canada LP hereafter Whirlpool will pay for Factory Specified
24. e static unless recommended by the manufacturer of the fabric softener or product explode Do not use heat to dry articles containing foam rubber or Do not allow children to play on or in the dryer Close similarly textured rubber like materials supervision of children is necessary when the dryer is Clean lint screen before or after each load used near children Keep area around the exhaust opening and adjacent Before the dryer is removed from service or discarded surrounding areas free from the accumulation of lint dust remove the door to the drying compartment and dirt Do not reach into the dryer if the drum is moving The interior of the dryer and exhaust vent should be cleaned periodically by qualified service personnel Do not dry articles that have been previously cleaned in washed in soaked in or spotted with gasoline dry cleaning solvents or other flammable or explosive substances as they give off vapors that could ignite or Do not install or store the dryer where it will be exposed to the weather See Electrical Requirements located in the installation Do not tamper with controls instructions for grounding instructions SAVE THESE INSTRUCTIONS ACCESSORIES Enhance your new washer and dryer with the following genuine Worksurface Whirlpool accessories For more information on options and The worksurface bridges ordering call 1 800 901 2042 or visit us at the washer and dryer and www whirlpool com ac
25. ed fabric care Uses Extra Low heat to gently dry delicate items Use this cycle for items that you do not wish to dry completely such as items to be ironed Medium load Fill the dryer drum up to about 1 2 full Large load Fill the dryer drum up to about 3 4 full Do not overload Items need to tumble freely CYCLE GUIDE MANUAL AND STEAM CYCLES NORMAL CASUAL ECO NORMAL DELICATE HEAVY DUTY DAMP DRY Auto Cycles NORMAL CASUAL ECO NORMAL DELICATE HEAVY DUTY DAMP DRY Auto Cycles 1 Manual Cycles Manual Gcle steam Cycle NN o TIMED DRY QUICK REFRESH TOUCH UP SMALL LOAD ENHANCED TIMED TOUCH UP DRY Steam model Non Steam model Adjusting drying time on Manual Cycles When you select a Manual Cycle the O y te M default time appears in the display Use the More Time A and Less Time des buttons to increase or decrease the time in 1 minute increments Press and hold to change the time in 5 minute increments The maximum dry time is 100 minutes Selecting the Drying Temperature A High heat setting may be used for drying heavyweight items such as towels and work clothes A Low to Medium heat setting may be used for drying medium weight items such as sheets blouses dresses underwear permanent press fabrics and some knits Use a no heat Air Dry setting for foam rubber plastic or heat sensitive fabrics Line dry bonded or laminated fabrics NOTE If you
26. eded When using Air Dry e Check that coverings are securely stitched e Shake and fluff pillows by hand periodically during the cycle e Dry item completely Foam rubber pillows are slow to dry NOTE Air Dry can only be used with Manual Cycles Available Options Cycle Details Wrinkle Shield Use to dry items to a damp level or for items that do nat require an entire drying cycle Select a drying temperature based on the type of fabrics in your load If you are unsure of the temperature to select for a load select the lower setting rather than the higher setting Wrinkle Shield For small loads of 3 4 items Wrinkle Shield Use to reduce wrinkles including from loads left in the dryer too long Cycle run time may be manually adjusted but Temperature is selectable Wrinkle Shield Use to reduce odors and light wrinkles NOTE Do not add dryer sheets Wrinkle Shield Use to reduce wrinkles including from loads left in the dryer too long Cycle run time may be manually adjusted and Temperature is selectable NOTE Do not add dryer sheets O O O a Q USING YOUR DRYER 44 WARNING Explosion Hazard Keep flammable materials and vapors such as gasoline away from dryer Do not dry anything that has ever had anything flammable on it even after washing Failure to follow these instructions can result in death explosion or fire WARNING To reduce the risk of fire electric shock or injury to pers
27. have questions about drying temperatures for various loads refer to the care label directions Default Time Drying Items to dry Cycle Temperature Any load NOTE Select Air Dry to dry foam rubber plastic or heat sensitive fabrics Timed Dry High Medium Low Extra Low Air Dry Small Load non steam models only Small loads and sportswear High Medium Low Extra Low Air Dry High Medium Low Extra Low Air Dry High Medium Mixed Loads Touch Up non steam models only Quick Refresh Steam models only Shirts blouses and slacks Mixed Loads Enhanced Touch Up Steam models only Settings and options shown in bold are default settings for that cycle Not all features and cycles are available on all models Nat all settings and options are available on each cycle Steam cycles on some models are designed for use with dry loads to loosen wrinkles reduce odors and refresh fabrics Using Air Dry Use the Air Dry temperature setting with Manual Cycles for items that require drying without heat such as rubber plastic and heat sensitive fabrics This chart shows examples of items that can be dried using Air Dry Est Time Minutes Type of Load 20 30 Foam rubber pillows padded bras stuffed toys Plastic shower curtains tablecloths 20 30 Rubber backed rugs 40 50 Olefin polypropylene sheer nylon 10 20 Reset time to complete drying if ne
28. ire chaque nouvel appareil WHIRLPOOLS Pour trouver des pi ces de rechange FSP ou des accessoires dans votre r gion Whirlpool Canada LP Centre pour l eXp rience de la client le 1 800 807 6777 Nos consultants fournissent l assistance pour Proc d s d utilisation et d entretien Vente d accessoires et de pieces de rechange Les r f rences aux concessionnaires compagnies de service de r paration et distributeurs de pieces de rechange locaux Les techniciens de service d sign s par Whirlpool sont form s pour remplir la garantie des produits et fournir un service apr s la garantie partout au Canada W10385092A W10385093A SP All rights reserved Tous droits r serv s Registered Trademark TM Trademark of Whirlpool U S A 2011 Whirlpool Canada LP licensee in Canada Marque d pos e TM Marque de commerce de Whirlpool U S A Emploi sous licence par Whirlpool Canada LP au Canada www whirlpool ca Pour plus d assistance Vous pouvez nous soumettre toute question ou probleme en crivant l adresse ci dessous Centre pour l eXp rience de la client le Whirlpool Canada LP Unit 200 6750 Century Ave Mississauga ON L5N 0B7 Dans votre correspondance veuillez indiquer un num ro de t l phone on peut vous joindre dans la journ e 4 11 Printed in U S A Imprim aux Etats Unis
29. m 4 5 minutes into the cycle The Wet light illuminates until the dryer goes into Cool Down with 1 minute of time remaining Damp This indicator is used with Auto cycles to show that the load is partially dried and items that you may wish to hang up or iron while still damp may removed Cool Down The dryer has finished drying with heat and is now tumbling the load without heat to cool it down and reduce wrinkling Done This will indicate that the selected cycle has ended and the load may be removed from the dryer If the Wrinkle Shield option has been selected the dryer may continue to tumble the load even if the Done indicator is lit Wrinkle Shield This indicator will light if the Wrinkle Shield option has been selected and is running The dryer will continue to tumble the load for up to 90 minutes after the cycle has ended Steam on some models This indicator will light when the Steam function is active NOTE Steam is not available on all models or on all cycles Control Lock This indicator will light when the controls are locked Press and hold the Cycle Signal button for 3 seconds to unlock CYCLE GUIDE AUTO CYCLES Settings and options shown in bold are default settings for that cycle Not all features and cycles are available on all models Nat all settings and options are available on each cycle Use Auto Cycles for better fabric care and energy savings The dryer senses moisture in the load
30. ng the bottom of the display to adjust settings See Cycle Guide for available settings on each cycle Not all settings are available with all cycles More O Steam Time g O Control Lock Less Time Sensing Wet Damp Cool Done Wrinkle Down Shield Cycle O More Signal 1 O Normal O Less press and hold for 3 seconds to lock unlock controls Temperature Dryness Wrinkle for manual cycle Level Shield for auto cycles 90 min More imate Time panes O Control Lock Less Time Sensing Wet Damp Cool Done Wrinkle O High Down Shield 1 Cycle O More Signal O Extra Low O Normal O Air Dry O Less press and hold for 3 seconds to lock unlock controls Temperature Dryness Wrinkle Level Shield for manual cycle for auto cycles 90 min Cycle Status Indicators The indicator bar in the display will let you know what stage the drying cycle is in process For more information on each stage see Cycle Status Indicators Temperature When using Manual Cycles or Enhanced Touch Up you may select a dry temperature based on the type of load you are drying Use the warmest setting safe for the garments in the load Follow garment label instructions NOTE Auto Cycles use a preset temperature that is not adjustable Dryness Level You may adjust the Dryness Level on Auto Cycles if desired If items are not as dry as you would like after an Auto Cycle select More Dry If items are too dry select Less Dry NOTE
31. nt is crushed or kinked or has too many turns F E F1 El F3 El etc The dryer is in need of service variable service codes Solution Ventilate the area When the odors or fumes are gone from the area rewash and dry the clothing Make sure water is connected to the dryer Check that water inlet hose is connected to both the faucet and dryer s water inlet valve Check that the water supply is turned on To remove odors left in garments after wearing select Quick Refresh steam models only This cycle is best for reducing wrinkles and odors from loads consisting of wrinkle free cotton cotton polyester blends common knits and synthetics Load removed before cooldown Allow the dryer to complete the cooldown portion of the cycle portion of cycle complete before removing the load Using a cycle with a high Select an Auto Cycle with a lower heat setting to avoid temperature setting overdrying the load The drying cycle has been Press and hold START PAUSE to restart the dryer interrupted by a power failure There may be a problem with your The dryer will continue to run when this diagnostic code is present Press any key to clear the code from the display and return to the estimated time remaining Try the following Check to see if a household fuse has blown or circuit breaker has tripped Electric dryers use two household fuses or breakers Replace the fuse or reset the circuit breaker Confirm the power cor
32. ons read the IMPORTANT SAFETY INSTRUCTIONS before operating this appliance 1 Clean the lint screen Clean the lint screen before each load Pull the lint screen straight up Roll lint off the screen with your fingers Do not rinse or wash screen to remove lint Wet lint is hard to remove Push the lint screen firmly back into place For additional cleaning information see Dryer Care 2 Load the dryer Open the door by pulling on the handle Place laundry in the dryer Add a dryer sheet to wet load if desired Close the door IMPORTANT Do not overload the dryer Items need to tumble freely Overloading can lead to poor drying performance and may increase wrinkling and tangling 10 A WARNING Lh Fire Hazard No washer can completely remove oil Do not dry anything that has ever had any type of oil on it including cooking oils Items containing foam rubber or plastic must be dried on a clothesline or by using an Air Cycle Failure to follow these instructions can result in death or fire 3 Press POWER Press the POWER button to turn on the dryer 4 Select the desired cycle NORMAL CASUAL ECO NORMAL DELICATE HEAVY DUTY DAMP DRY Auto Cycles Manual Cycle Steam Cycles AA TIMED DRY QUICK REFRESH ENHANCED TOUCH UP Steam model shown Select the desired cycle for your load See the Cycle Guide for more information about each cycle Not all cycles are on
33. or air temperature and shuts off when the load reaches the selected dryness level Use the NORMAL dryness level to provide optimal energy savings Items to dry Cycle Drying Dryness Default Available Cycle Details Temperature Level Time Options Work clothes casual Normal wear mixed cottons sheets corduroys Work clothes casual Eco Normal wear mixed cottons sheets corduroys Heavyweight items such as towels jeans or heavy work clothes Shirts blouses Casual permanent press synthetics lightweight items Load Size Recommendations For best results follow the wet load size recommendations noted for each cycle Small load Fill the dryer drum with 3 4 items not more than 1 4 full Undergarments Delicate Extra Low blouses lingerie performance wear washable woolens Clothes to come out Damp Dry Low suitable for ironing ul Wrinkle Shield More Wrinkle Shield Normal Less Wrinkle Shield Wrinkle Shield More Wrinkle Shield Normal Less Wrinkle Shield Uses Medium heat to dry large loads of mixed fabrics and items Normal is the preferred energy cycle Recommended for average sized loads of medium weight items where improved energy savings is desired Offers stepped drying starting with High heat followed by Medium heat for enhanced fabric care and energy savings Uses a stepped drying temperature from Medium to Low for improved moisture removal and enhanc
34. rmal The thumping sound should diminish after a few minutes of use A small object caught between the Check the front and rear edges of the drum for small objects Clean edges of dryer drum out pockets before laundering The dryer may vibrate if not properly installed See the Installation Instructions All four dryer feet should be in firm contact with the floor Dryer will not heat Humming or whining noise with Steam cycle selected Thumping noise Rattling or vibrating noise Dryer isn t properly leveled Clothing is balled up in dryer When balled up the load will bounce causing the dryer to vibrate Separate the load items and restart the dryer Gas valve operating On gas dryers you may hear the gas valve clicking as it opens and closes This is normal Dryer Results Clothes are not drying Lint screen is clogged with lint Clean lint screen before each load satisfactorily or drying times are too long The exhaust vent or outside Run the dryer for 5 10 minutes Hold your hand under exhaust hood is clogged with lint the outside exhaust hood to check air movement If you restricting air movement do not feel air movement clean exhaust system of lint or replace exhaust vent with heavy metal or flexible metal vent See Installation Instructions Clicking noise The exhaust vent is not the correct length Check that the exhaust vent is not too long or has too many turns Long venting will increa
35. se drying times See Installation Instructions The exhaust vent diameter is not Use 4 102 mm diameter vent material the correct size The dryer is not level Clothes not contacting the moisture sensors during Automatic cycles See Level the Dryer in the Installation Instructions The Air Dry temperature setting has been selected Select the right temperature for the types of garments being dried See Cycle Guide 15 TROUBLESHOOTING First try the solutions suggested here or visit our website at www whirlpool com help for assistance and to possibly avoid a service call Dryer Results cont Clothes are not drying The load is too large and heavy Separate the load to tumble freely satisfactorily or drying to dry quickly times are too long Dryer sheets are blocking the grille The air outlet grille is just inside the door behind the lint screen Check that it is not blocked by a dryer sheet Use only one dryer sheet and use it only once The dryer is located in a room with Proper operation of dryer cycles requires temperatures above temperature below 45 F 7 C 45 F 7 C The dryer is located in a closet Closet doors must have ventilation openings at the top and bottom of the door The front of the dryer requires a minimum of 1 25 mm of airspace and for most installations the rear of the dryer requires 5 127 mm See Installation Instructions Cycle time is too short The lo
36. ter warranty service anywhere in the United States and Canada In the U S A Features and specifications on our full line of appliances Installation information m Specialized customer assistance Spanish speaking hearing impaired limited vision etc You can write with any questions or concerns at Whirlpool Corporation Customer eXperience Centre Customer eXperience Center Whirlpool Canada LP 553 Benson Road Unit 200 6750 Century Ave Benton Harbor MI 49022 2692 Mississauga ON L5N 0B7 Please include a daytime phone number in your correspondence ASSISTANCE OU SERVICE Avant de faire un appel pour assistance ou service veuillez v rifier la section D pannage ou consulter www whirlpool com help Cette v rification peut vous faire conomiser le co t d une visite de r paration Si vous avez encore besoin d aide suivre les instructions ci dessous Lors d un appel veuillez conna tre la date d achat et les num ros au complet de mod le et de s rie de votre appareil Ces renseignements nous aideront mieux r pondre votre demande Si vous avez besoin de pi ces de rechange ou pour commander des accessoires Si vous avez besoin de commander des pi ces de rechange nous vous recommandons d utiliser seulement des pi ces sp cifi es par l usine FSP Ces pi ces conviendront et fonctionneront bien parce qu elles sont fabriqu es selon les m mes sp cifications pr cises utilis es pour constru
37. used by improper venting are not covered sure to follow the Installation Instructions supplied by the warranty and will be paid by the customer regardless with your dryer for final product check Of who installed the dryer Clear away items from the front the dryer Use Auto Cycles for better fabric care and energy savings Use the Auto Cycles to provide the most energy savings and enhanced fabric care from the dryer During Auto Cycles drying air temperature and moisture level are sensed in the load This sensing occurs throughout the drying cycle and the dryer shuts off when the load reaches the selected dryness Use the NORMAL DRY dryness level to provide optimal energy savings With Manual Cycles the dryer runs the amount of time set and sometimes results in shrinkage wrinkling and static due to over drying Use Manual Cycles for the occasional damp load that needs a little more drying time or when using the drying rack Tips for getting the best performance from your steam dryer on some models Results may vary depending on fabric 100 cotton The Quick Refresh Cycle is best for smoothing out wrinkles garments with wrinkle free finish may yield better results and reducing odors from loads consisting of one to four than those without 100 cotton items may require dry items of wrinkle free cotton cotton polyester blend additional touching up after the Steam Cycle common knits and synthetic garments Use of dryer sheet
Download Pdf Manuals
Related Search