Vitek VTC-C2B-HS Instruction manual
Contents
1. No DC Iris 1 Damp 2 Damp 3 Drive 4 GND Installation Instructions Installation and commissioning Instructions Make sure the power is removed before installation Follow the order for applying power When using 12VDC or 24VAC power make power connections at camera first then apply power this will help avoid unnecessary power surges to camera Remove the dust protection cap from the lens mount Screw the lens onto the camera firmly do not over tighten Plug the lens into the lens connector on the rear of camera case Mount the camera to the wall or ceilling with a corresponding mounting bracket through the camera mount holes 1 4 thread insert on its top or bottom Care should be taken the cable is NOT damaged kinked or exposed in any hazardous area Do not expose the camera lens directly to a strong light source such as the sun or spot light AUN Setting the back focus adjustment For easier and better adjustment this camera provides FOCUS ADJUST menu which will assist you in the focusing of the camera When enabling FOCUS ASSIST menu follow the procedure to get the best back focus adjustment 1 Set the lens for the zoom position to WIDE and the focus position to INFINITE 2 Point the camera at an object about 30 away 3 Adjust Back focus adjusting Flange until the optimum focus is achieved2. DEBLUR It enables to reduce the blur in certain indoor environments Noise or color rolling may increase 2 2 MANUAL default NORMAL for None LED type Horizontal wave or bar may be seen when MANUAL is selected and the camera is working under florescent or similar lights 3 FOCUS ASSIST FOCUS ASSIST DN DWELL 5s POP ON FOCUS OFF RETURN RET4 FOCUSING STATUS Usually cameras are installed in the day time and they often become OUT OF FOCUS at night time and IN FOCUS again the next day This problem can occur with cameras regardless of types or manufacturers FULL HD MEGA PIXEL CAMERA Operating Instructions FOCUS ASSIST menu is a unique and patented feature that assists in focusing by simulating DAY amp NIGHT conditions Set zoom first and adjust focus to get best picture when switching from DAY to NIGHT DN DWELL 5s ICR switcher switches DAY to NIGHT and back at the interval of D N DWELL to help with focusing in DAY and NIGHT modes POP ON FOCUS OFF ON zooms into the center of the picture at 2X for better focusing FOCUSING STATUS ON Shows focus indicator on how focus is set When blue bar doesn t show up try the lens focus to NEAR and FAR The maximum blue bar indicates the best focusing position 4 PICT ADJUST PICTURE WHITE BAL SHARPNESS COLOR GAIN GAMMA SHADING RETURN 4 1 WHITE BAL default ATW ATW ATWext ONE PUSH and MANUAL are avai
3. AGC Max DSS x2 Day Night Mechanical IR Cut Filter True Day Night Electronic shutter speed Auto 1 30sec 1 60 000sec White Balance ATW ATWext One Push Manual Brightness YES DSS Sens Up OFF AUTO X2 X32 DNR 3D DNR WDR YES Privacy YES 10 Zones Motion Detection YES ACE Adaptive Color Enhancement YES Advanced OSD Functions Defog BLC HLC Motion Deblur Pixel Defect Compensation Title Set Mirror Flip LSC Lens Shade Compensation Communication RS 485 Pelco D P HD Transmission Range Up to 700 Depending on cable characteristics and integrity Operating Conditions 14 122 F 10 50 C lt 80 RH Input Voltage 12VDC 24VAC Dual Voltage Power Consumption 12VDC 250mA 3Watt Power Consumption 24VAC 230mA 2 8Watt Dimensions 1 89 x 2 09 x 2 89 W x H x D 23 LIMITED LIABILITY WARRANTY VITEK products carry a three 3 year limited warranty VITEK warrants to the purchaser that products manufactured by VITEK are free of any rightful claim of infringement or the like and when used in the manner intended will be free of defects in materials and workmanship for a period of three 3 years or as otherwise stated above from the date of purchase by the end user This warranty is nontransferable and extends only to the original buyer or end user customer of a VITEK Authorized Reseller The product must have been used only for its intended purpose and not been subjected to damage by
4. LSC Lens Shade Compensation BLC HLC Motion Deblur Pixel Defect Compensation Title Set Back focus Flange Top performance at low light sensitivity Sens up On OSD menu amp CVBS Video output BNC for easy installation amp maintenance Circuit protection against reverse power polarity Isolated power supply to help avoid ground loop problem Remote control via RS 485 Pelco D P General Description This camera incorporates a full 1920 x 1080p HD camera module With ICR mechanism Enhances its sensitivity about 10x at night time Can accept infrared light With Intelligent Focus Indicator and FOCUS ASSIST menu Offers easy adjustment of Focus With 24VAC 12VDC dual power design Offers flexibility of installation Composition J Operating Video Sub out Instruction Cable 1pc OQ vu Dust Protection L Wrench Cap 1pc 1 5mm 1pc Compact Box Camera Dimensions unit inches 2 87 ES 2 38 i h 1 73 2 09 Part Names Mount Holes Top Bottom L Wrench Dust Protection Cap Back focus Front Case adjusting Flange REAR VIEW voto mm s P e D Video out connector BNC Power input terminal CVBS 9 OSD Control Joy stick 4 DC Auto Iris Lens connector POWER DCLENS S J PIN 4 PIN 2 Lens Connector for Auto Iris lenses
5. 60P 50P but the image refresh rate is 30P 25P Cropped image has narrowed field of view 5 3 COMM SET UP COMM SETUP defines the CAM ID BAUD RATE and PROTOCOL Data length stop bit and parity are fixed to 8bit 1stop bit and no parity bit CAM ID Assigns the camera ID from 1 255 for the comm address BAUD RATE Selects the baud rate from 2400 115200 PROTOCOL Selects the comm Protocol from PELCO D P or VISCA Refer to TIP for setting RS 485 communication with PTZ Controller 5 4 LANGUAGE default ENG 8languages are available for ENGLISH JAPANESE GERMAN FRENCH ITALIAN SPANISH POLISH and TURKISH When changing LANGUAGE select language and press to load 5 5 FACTORY DEFAULT default NO RECALL Loads and saves the factory defaults FULL HD MEGA PIXEL CAMERA Operating Instructions Setting for RS 485 Communication with PTZ Controller e Enter the MENU Press buttons 9 5 PSET PRESET e Move the cursor in the MENU Moves UP DOWN LEFT RIGHT Joy stick e Select or Choose value in the MENU era Press button OPEN IRIS OPEN e D Zoom IN Press button TELE e D Zoom OUT Press button WIDE SL 5 Detailed Specifications Sensor 1 2 9 Sony CMOS Resolution 2 1 MegaPixel 1080p 720p S N More than 50 dB AGC Off Video Output 1x HD SDI BNC 1x SD CVBS BNC Lens CS Mount Lens Support Not Included Digital Zoom 1 1x 8x Minimum Illumination 0005 Lux
6. e Pay attention to safety when running the connection cable and observe that the cable is not subjected to heavy loads kinks or damage and no moisture can get in Never open the device The warranty becomes void if repairs are undertaken by unauthorized persons Maintenance and repair have to be carried out only by authorized service centers Useonly a mild detergent to clean the housing The camera should never be operated beyond the technical specifications This can lead to damaging the camera and voiding the warranty The camera should never be operated in water FULL HD MEGA PIXEL CAMERA Contents p 02 03 Safety Precaution p 04 Contents p 05 Features p 06 Composition p 06 Dimensions p 07 Part Names p 08 09 Installation Instructions p 10 22 Operating Instructions p 23 Specifications Features Key Features Full HD 2Mega Pixel HD SDI CAMERA 1920x1080 30p 25p True WDR Wide Dynamic Range Improved Noise filter with the enhanced 3D NR CS mount supported Option C mount adaptor Non Compressed digital streaming up to 1 485Gbps Intelligent focusing status indicator on screen Dual Filter Switcher Pointing Zoom which enables the flexible zooming of any area Smart Motion Zoom in combination with Pointing Zoom Selectable Scale down or Cropped image to 720p mode Motion Detection Privacy Mask Defog Sens up x32 D WDR H V HV Flip D Zoom 1 1x 8x
7. 4 Set the lens zoom position to TELE and adjust the lens focus for best focus 5 Set the lens zoom position to WIDE again check if the focus adjustment was the best If not re adjust Back focus Flange slightly 6 After the setting tighten the Flange lock screw with L wrench supplied Start up When the camera is powered properly it starts up with initializing the internal parameters Installation Instructions Using OSD Controller Setup menu can be accessed and controlled by OSD control joy stick on the rear of the camera unit Five commands are available with the joy stick The design of rear panel could be different according to the camera models e Description of the joystick operation 1 SET Key e Access to the menu or enter the setting To enter the main menu press the Set Key down for about 2sec 2 UP DOWN Key 4 Choose the desired sub menu and to move the cursor up or down 3 LEFT RIGHT Key lt P Set up the value of the selected menu Used to adjust the desired menu selection and to move the cursor left or right 4 i denotes a long press down for about 2 seconds FULL HD MEGA PIXEL CAMERA Operating Instructions OSD menu Startup Press e OSD menu Joy stick key down for about 2 seconds to access the setup menu mode MENU V3 12 1 EXPOSURE 4 2 LENS DCa 3 FOCUS ASSIST 4 4 SCENE ENHANCE NORMAL 5 3D NR MID 6 DAY NIGHT AUTO 7 PICT ADJUST 4 8 S
8. ACY 10 Privacy zones which can be enabled individually by ZON DISP are available to mask the video ZONE NUMBER Set a number to select a privacy zone from 1 10 ZONE DISP ON enables to display relevant privacy zone H POS V POS H SIZE and V SIZE Adjust the size and position of zone COLOR Select the color used for masking the zone form eight colors TRANSPARENCY Defines the transparency for the mask zone FULL HD MEGA PIXEL CAMERA Operating Instructions 5 3 MOTION default OFF MOTION can detect the changes in the motion window and displays the results in blocks and or a text message on screen SENSITIVITY Adjusts the detection sensitivity for motion Higher value increases the sensitivity to detect small motion easier Too low of sensitivity will cause erratic detection H POS V POS H SIZE V SIZE Adjust the size and position of the detection window BLOCK DISP ON enables to display the blocks for the detected area MOTION OSD ON enables to display a text message MOVING SMART MOTION ZOOM ON enables to Automatic Zoom IN OUT when motion is detected and also enables MOTION OSD to ON Area to be zoomed in by SMART MOTION ZOOM can be set at SPECIAL MOTION gt SMART MOTION ZOOM gt ZOOM TARGET Adjusting 4 Joystick for ZOOM TARGET varies the viewing angle to be zoomed when motion occurs Set the video left and right and or up and down by MIRROR FLIP X SMART MOTIO
9. Iris and Shutter can be set to fix Flickerless Reduces the flicker in video when US 60Hz EU 50Hz mode is used in 50Hz 60Hz fluorescent lighting respectively 1 2 BRIGHTNESS default 10 Adjusts the brightness of video 0 20 2 3 SENS UP default AUTO Brighter video can be obtained by increasing the exposure time at night with SENS UP SENS UP is the maximum integrations of frame by DSS Digital Slow Shutter in low light AUTO SENS UP is enabled or disabled automatically by the scene brightness Higher SENS UP can get brighter video but slower frame rates with motion blur and more white pixels If set to AUTO maximum integration limit for SENS UP can be set to x2 x4 X8 x16 X32 in SENS UP menu OFF Disables SENS UP 2 4 AGC default 12 AGC 0 20 amplifies the video gain for brighter video but more noise and white pixel will occur AGC level less than 10 disables AUTO in DAY NIGHT FULL HD MEGA PIXEL CAMERA Operating Instructions 2 LENS Lens can be selected either DC or MANUAL lens Lens MUST be set to DC for the best image when DC iris lens is installed DC MANUAL MODE DEBLUR MODE NORMAL RETURN RET 4 RETURN RET 4 2 1 DC default DEBLUR for None LED type Selects lens mode according to installation location INDOOR or DEBLUR for indoor installation according to environment OUTDOOR Optimized for outdoor environment INDOOR Optimized for indoor environment
10. MAL BLC Improves the visibility of bright back light Outside area of BLC window can over saturate BLC has a target window for compensation and its size and position can be set by H POS V POS H SIZE and V SIZE HLC Cuts out the bright area with black mask and excludes it from compensation Lower HLC LEVEL the more sensitive it is to bright light 3D NR MID Enables to set OFF LOW MID and HIGH 3D NR is a very sophisticated and powerful time based noise reduction technology by monitoring the noise for the several video frames and defining and eliminating them consecutively at low light Higher setting reduces noise more but results in losing the sharpness and tail effects or motion blur may occur DAY NIGHT EXT for IR LED AUTO for No IR LED Sets DAY NIGHT to EXT AUTO COLOR and B W SMART IR can be set to reduce saturation by strong IR illumination at night in any menu of EXT AUTO and B W NIGHT Setting SMART IR in any menu is identically applied to other menu Zero 0 turns off SMART IR and High setting decreases saturation but the corners will become darker accordingly IR LED Control AUTO OFF is available with IR LED model only If IR LED is set to OFF IR LED will be turned OFF but DAY or NIGHT is still determined by the built in light photo sensor EXT DAY or NIGHT is determined by the built in light photo sensor Camera with IR LED must be set to EXT AUTO Used when DAY or NIGHT is d
11. N ZOOM does not work in low light condition and BW e STAY ZOOMING Sets the duration time for zooming by Motion N CAUTION Set the direction of video by MIRROR FLIP before SMART MOTION ZOOM setting Otherwise ZOOM TARGET could be different from your intention 5 4 PIXEL DEFECT default OFF Detects and compensates the white pixels which become defective Once CALIBRATE is selected the pixel calibration is initiated with lens closed and can not be canceled THRESHOLD Defines the level of detection and low value detects more pixels Be sure to set the value so that the pixels are uniformly blinking over the entire screen Too low of value will get bad results because too many pixels are detected as bad pixels and the maximum number of pixels for compensation will be filled by the upper area e EXECUTE Long pressing will execute the pixel calibration for the detected pixels Menu will exit automatically after compensation FULL HD MEGA PIXEL CAMERA Operating Instructions 5 5 TITLE SET Camera title name can be set and edited up to 15 alpha numeric and symbolic characters from ASCII codes ENGLISH only A V 4 moves the cursor to next input Choose a character and selects it The selected characters are added and displayed on the top left Corner and the cursor moves right automatically for next input SP Space is inserted when pressed e BS Cursor moves back when pressed
12. PECIAL 4 9 SYSTEM 4 A EXIT SAVE amp EXIT Direct Control menu man DEFAULT DESCRIPTION Sets EXPOSURE MODE BRIGHTNESS SENS UP AGC and FXEOSURE g MOTION DEBLUR LENS DC Sets Lens types FOCUS ASSIST Sets FOCUS SCENE NORMAL SCENE ENHANCE provides several ways to enhance the video ENHANCE in various environments with settings in NORMAL WDR D WDR BLC and HLC NORMAL Optimized for normal indoor and outdoor in good lighting condition WDR This function extends the gain range of the screen that is useful if the camera takes a simultaneous picture of both indoor and outdoor It improves contrast of the picture in outdoor scenery as well as indoor Video image is processed from two images by dual shutter long and short shutter in a field to provide the best dynamic range Highlight area is compensated by the short shutter and dark area is compensated by the long shutter Final video may have less contrast compared to the conventional camera which does not have WDR function 3 CVBS video signal Connecting 2nd video to CVBS port disables WDR function temporary It should be considered when installer adjusts the video with installation monitor via CVBS video signal D WDR Improves the visibility by compensating the video gain for the dark area Noise can increase in the dark area accordingly FULL HD MEGA PIXEL CAMERA Operating Instructions SCENE ENHANCE NOR
13. VITEK VTC C2B HS 2 1MP HD SDI Smart WDR Camera yITEK FEATURES e 1 2 9 Sony CMOS e 2 1 MegaPixel With full 1080p 720p HD SDI Output tS PTE 292M Smart Motion Zoom tracks motion then intelligently zooms into that area of the frame Mechanical IR Cut Filter True Day Night e Small scale design to fit in 5 dome enclosures such as the Pelco DF5 Housing Fully programmable advanced WDR e Sensitivity of 0 0005 Lux Advanced OSD Functions Defog BLC HLC Motion Deblur Pixel Defect Compensation Mirror Flip 100 Pure Digital Transmission of video data Up to 700 HD Transmission Range Depending on cable characteristics and integrity 12VDC 24VAC Dual Voltage Operation On 3 Safety Precaution To prevent fire or shock hazard do not expose the unit to rain or moisture To prevent electric shocks and risk of fire hazards do NOT use other than specific power source CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The symbol is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons The symbol is intended to alert the user to the presence of importan
14. center of the floor in a room and result in losing the image of door on the side wall However POINTING ZOOM can be set to see the door side and zoom in on that area without missing the IMPORTANT security point POINTING ZOOM can be activated by the joystick operations of A for zoom in and V for zoom out POINTING ZOOM H POINTER 10 V POINTER 10 RETURN RET a H POINTER 10 Sets the horizontal location of area to be zoomed by POINTING ZOOM V POINTER 10 Sets the vertical location of area to be zoomed by POINTING ZOOM FULL HD MEGA PIXEL CAMERA Operating Instructions EXAMPLE OF SMART MOTION amp POINTING ZOOM Conventional Zoom FULL HD MEGA PIXEL CAMERA Operating Instructions 6 SYSTEM SYSTEM TV SYSTEM US NT RESOLUTION 1080P COMM SETUP d LANGUAGE ENG FACTORY DEFAULT NO RETUTN RET4 5 1 TV SYSTEM default US or EU Selects HDTV standards for US 60HZ or EU 50HZ By this selection 2nd analog video output switches to NTSC or PAL accordingly 5 2 RESOLUTION default 1080P Three resolutions 1080P 720P SCALED 720P CROPPED are available 1080P outputs 1920x1080 video at the frame rate of 30P 25P 720P SCALED Image is scaled down from 1080P and outputs 1280x720 video without loss of field of view at the frame rate of 30P 25P 720P CROPPED image is cropped at the center area from the image sensor and outputs 1280x720 video at the frame rate at
15. e CLR Clears all the characters on input line when pressed e POS To be able to set the title position by A V 4 and e 5 6 DISPLAY Enables or disables the OSD display ID ON enables camera ID display defined by SYSTEM gt COMM SETUP gt CAM ID TITLE ON enables camera title name display set by SPECIAL TITLE SET D ZOOM RATIO ON enables to display the zoom ratio on the bottom right corner DZx x will display by multiplying the actual digital zoom ratio 5 7 DEFOG default OFF AUTO Enhance foggy video automatically according to status of scene MANUAL Sets to enhance foggy video manually regardless of status of scene LEVEL LOW MID HIGH Video quality can be less in normal environments 5 8 POINTING ZOOM ON enables to set off centered location to be the center of zoom H POINTER V POINTER Able to set the location of zoom center D Zoom is available DZx1 1 x8 0 X CAUTION Set the direction of video by MIRROR FLIP before POINTING ZOOM setting Otherwise location of zoom center could be different from your intention Operating Instructions Detail Function Description SMART MOTION ZOOM SMART MOTION ZOOM enlarges the area defined by a yellow window to a full size image when motion is detected in the black window SMART MOTION ZOOM window can be re sized by adjusting D ZOOM RATIO and moved by H POINTER and V POINTER UNLIKE the conventional zoom
16. etermined by light level through the lens and DAY from to NIGHT is switched automatically by the Scene brightness D lt gt N THRESHOLD D lt gt N DELY and SMART IR can be set in the menu When EXPOSURE gt AGC is less than 12 DAY NIGHT AUTO is disabled and forcibly switches to color DAY to avoid malfunction EXT B W NIGHT and COLOR DAY is independent on AGC level When EXTERNAL IR LED is used with NON IR LED model please set to IR LED MODE ON B W NIGHT Forcibly removes IR cut filter and switches to B W regardless of light level COLOR DAY Forcibly DAY NIGHT is disabled and outputs color video PICT ADJUST Sets WHITE BAL SHARPNESS COLOR GAIN GAMMA SHADING SPECIAL Sets MIRROR FLIP PRIVACY MOTION PIXEL DEFECT TITLE SET DISPLAY DEFOG POINTING ZOOM SYSTEM Sets TV SYSTEM RESOLUTION COMM SETUP LANGUAGE and FACTORY DEFAULT EXIT SAVE amp EXIT Exits the menu after saving the parameters EXIT Exits the menu without saving the menu FULL HD MEGA PIXEL CAMERA Operating Instructions 1 EXPOSURE EXPOSURE SHUTTER AUTO BRIGHTNESS ss pss dO SENS UP OFF AGC esses pesca RETURN RETd 1 1 SHUTTER default AUTO Ability to set EXPOSURE MODE to AUTO MANUAL and Flickerless MANUAL and Flickerless modes disable SENS UP and MOTION BLUR functions AUTO Optimizes the video level by controlling the iris and the shutter speed automatically MANUAL
17. lable for white balance modes ATW White balance is continuously working along with the color temperature changes in the range of 2 000K 8 500K ATWext White balance is continuously working along with the color temperature changes in the range of 1 800K 11 000K ONE PUSH White balance works only while e is pressed MANUAL White balance is fixed to the settings of R GAIN and B GAIN This mode can be used only when the color temperature does not vary 4 2 SHARPNESS default 10 Adjusts the sharpness of video 0 20 4 3 COLOR GAIN default 10 Adjusts the color level of video 0 20 FULL HD MEGA PIXEL CAMERA Operating Instructions 4 4 GAMMA default 0 5 Adjusts the gamma of video 4 5 SHADING default OFF ON enables the ability to compensate the shade caused by a wide lens setting 5 SPECIAL SPECIAL MIRROR FLIP OFF PRIVACY 4 MOTION OFF PIXEL DEFECT OFF TITLE SET 4 DISPLAY 4 DEFOG OFF POINTING ZOOM 4 RETURN RET4 5 1 MIRROR FLIP default OFF Reverses the video left and right and or up and down by MIRROR FLIP OFF Normal display without mirroring or flipping Hor Video is reversed left and right Ver Video is reversed upside down HV Video is reversed left and right and upside down When the video is reversed by Ver or HV then the joystick directions are reversed accordingly This feature is very useful when a camera is installed upside down 5 2 PRIV
18. misuse willful or accidental damage caused by excessive voltage or lightning The product must not have been tampered with in any way or the guarantee will be considered null and void This guarantee does not affect your statutory rights Contact your local VITEK Reseller should servicing become necessary VITEK makes no warranty or guarantee whatsoever with respect to products sold or purchased through unauthorized sales channels Warranty support is available only if product is purchased through a VITEK Authorized Reseller 28492 CONSTELLATION ROAD VALENCIA CA 91355 WWW VITEKCCTV COM Version 1 1 Dec 2014
19. t operating and maintenance servicing instructions in the literature accompanying the unit Warning This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense Caution Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment Mains power quality should be that of a typical commercial environment If the user of the model requires continued operation during power mains interruptions it is recommended that the model be powered from an uninterruptible power supply UPS or a battery Safety Precaution id NOTICE The image used in this instruction manual are processed to help comprehension and may differ from actual video of the camera Avoid installing in areas where shock or vibration may occur
20. which can zoom in out the center area of image only the flexible zoom location and area SMART MOTION ZOOM differentiates its usefulness from others That is a conventional camera installed in the corner of the ceiling can zoom the center of the floor in a room and result in losing the image of door on the side wall However SMART MOTION ZOOM can be set to see the door side and zoom in that area without missing the IMPORTANT security point SMART MOTION ZOOM H POINTER 10 V POINTER 10 D ZOOM RATIO MZ2 0 MOTION CHK CUNT 2 RETURN RET4 H POINTER 10 Moves MOTION ZOOM area Yellow window horizontally V POINTER 10 Moves MOTION ZOOM area Yellow window vertically D ZOOM RATIO MZ2 0 Sets the area size to be digitally zoomed when motion occurs in the black window MOTION CHK COUNT 2 SMART MOTION ZOOM is activated after the motions in MOTION CHK COUNT are detected in a certain period For example SMART MOTION ZOOM is activated after set of triggers by motion FULL HD MEGA PIXEL CAMERA Operating Instructions POINTING ZOOM This camera has a very useful and powerful feature POINTING ZOOM which can zoom in out of any area in the scene UNLIKE the conventional zoom which can zoom in out the center area of image only the flexible zoom location and area POINTING ZOOM differentiates its usefulness from others That is a conventional camera installed in the corner of ceiling can zoom the
Download Pdf Manuals
Related Search