Xwave Pump 6800 User Manual
Contents
1. assemble step by step according to the figure right 2 se the plastic screw 11 to fix the position and place the suction cu on the back of the pump 3 ount the whole set of Xwave to the vertical aquarium pane by the plastic screw 10 amp 7 a1 3 6 Attaching the wave pump to horizontal aquarium pane 1 The package contains several components of the product Please assemble step by step according to the figure right 2 Use the plastic screw 11 12 to fix the position and place the i suction cup on the back of the pump 3 Mount the whole set of Xwave to the horizontal aquarium pane by the plastic screw 10 7 Attaching the wave pump by the cupule holder o 1 The package contains several components of the product 15 D amp a 1 Please assemble step by step according to the figure right 2 Place the cupule on the back of the pump 3 Mount the whole set of Xwave to plain surface of aquarium by the cupule holder SA 8 Beginning operation for wave Pump 1 Please assemble the pump plug into the corresponding sockets of the dirver box 2 Submerge the wave pump in the water To prevent the air being drawn in keep the closed zone upwards 3 Set the 6 position slide switch to the Off position Then connect the wave driver to the power supply 4 By sliding the switch the speed and the performance of the wave pump can be adjusted to among 50 60 70 80 and 100 percent to your desired output 5 The2. of the bearings considerably and can lead it to exclusion from guarantee see cleaning the pump 12 Troubleshooting Before requesting service check the following chart Condition Speculation Counter measures 1 Blockage in the pump 1 Disassembel andclean the pump The pump does not work 1 Some particles indide the 1 Disasseble and clean the motor pump 2 The baring worn affer 2 Replace the propeller an edtensive usage The noise from the pump 1 Reduce the lime additive The pump furs i Overdose of lime or submerge the pump in additives e g Cause lime a 10L 2 6gal bucket half deposites on the bearing full with wather and 20mL parts of vinegar essence Allow the pumpto run for one to two rs Avoid splashes Subsequently thoroughly rines by tap water The drive unit is jammed due Remove the blockage to wear lime small fish or Clean the pump and replace the drive unit if necessary The pump stops and the driver box alarms snail again automatically The pump will start operating 4 Safety Instruction 6 The wave pump can only work with the original wave pump driver box 7 Maximum operating temperature of aquarium waster 40degree Celsius 8 Please read the manual before use Keep it in a safe place for future reference 5 Attaching the wave pump to vertical aquarium pane 1 The package contains several components of the product Please
3. Xwave Pump 6800 Manual 1 Contents of package Part NO Part Name Part NO Part Name 1 wave pump 9 grip holder 2 rotatable link head 10 lock screw 4 lock nut 11 screw 4 rotatable shelf 12 screw 5 conector panel 13 lengthing connector 6 connector bend 14 cupule 7 lengthing connector 15 fix board for cupule 8 slide block 16 wave pump driver 2 Disposal In accordance with RL2002 96 EG The product must not be added to normal household waste It must be disposed of properly 3 General Feature Xwave Wave Maker Series is designed to create the most natural simulation of the ocean waves in your tank It can simulate the pulsing wave and turbulence current which occur in the natural environment Wave pump is operated by means of a 120V AC US Model 230V AC EU Model to 12VDC wave pump driver box It creates a high flow volume at moderate speeds By the Xwave Multicontrol System the speed can be continuously controlled to execute the preset prorgam For details of the Xwave multicontrol system please refer to the corresponding operating manual It also can be used with Xwave Rotary Machine to make the current upgraded from 1 dimension to 2 dimension level For details of the Xwave Rotary Machine please refer to the corresponding operating manual 4 Safety Instruction 1 The main voltage must be corresponding to the operating voltage of the Xwave indicated 2 The wave pump driver bo
4. wave pump may have running noises at the beginning After one week running in period the noise will simply become softer 6 For details of the connection Xwave multicontrol system please refer to the corresponding operating manual 14 WAVE ADJUST LLiLLL Wave pump An Extra Ordinary WA Xwave Pump 6800 User Manual A pe V9 2007
5. x must be placed at a dry and ventilated position which is free from water splashing 3 Do not operate pump without water 4 Disconnect all the electric units when you are working with the aquarium 5 Never remove the plugs of the wave pump from the wave pump driver box as long as it is connected with electricity 9 Blocking When the pump is blocked for 3 seconds an alarm in the wave driver box is activated at the same time the wave pump is switched off After removal of the blockage the pump will start again automatically 10 Automatic rinsing process In order to clean the water inlet suction housing set the pump to 100 percent output and uses your hand to close up the water outlet for 10 seconds Then all dirt and scum trapped by the suction housing would be removed by the turbulences produced We suggest to this process however cannot substitute the disassembling and cleaning of the pump 11 Guarantee One year guarantee is provided for the wave pump after the date of purchase covering all material and workmanship defects Method Defective units should be returned well packed together with the sales slip to the retailer or the manufacturer Unpaid consignments will not be accepted and will be returned to the sender immedi ately Exclusion from guarantee The guarantee does not cover any damage caused by incorrect handling and any technical modification made by the user Sand and lime deposits may increase the wear
Download Pdf Manuals
Related Search