USER MANUAL - Appliances Online
Contents
1. Armoire vin Wine Preservation Technology USER MANUAL V30SG V40SG V50SG V30SG e AL V30SG e V40SG e AL V40SG e V50SG e V30SG 2e AL V30SG 2e V40SG 2e AL V40SG 2e V50SG 2e V40DG 2e AL V40DG 2e V50DG 2e WARNING The information in this document is subject to modification without any prior notice VINTEC offers no guarantee for our wine cellar if it is being used for any purpose other than that for which it was specifically designed VINTEC cannot be held responsible for any error in this manual VINTEC is not responsible or liable for any spoilage or damage to wines or any other contents incidental or consequential to possible defects of the wine cellar Warranty applies to the wine cellar only and not to the content of the wine cellar Allow 24 hours before switching on the wine cellar During this time we recommend that you leave the door open to clear any residual odors BEFORE LOADING amp PLUGGING IN THE WINE CELLAR Important All models without front venting air opening are strictly for free standing only see technical chart Recommendations The location you have selected for your wine cellar should be unencumbered and well ventilated be well away from any heat source and direct sunlight not be too damp laundry pantry bathroom etc have a flat floor have a standard and reliable electricity supply standard socket to country standards linked to the ground it i2. gt 2 This wine cabinet is not designed to be fully integrated behind a joinery door V50 s Installation instructions 1 Wine Cabinet dimensions 3 Please note that a minimum cut out of 625mm is required to facilitate installation removal and servicing 4 This wine cabinet requires 10mm clearance on both sides and top 30mm clearance at the rear Where possible a ventilation grid should be installed in the 30mm clearance at the rear either in the sides top or back of the joinery Minimum grid size is 200mm x 40mm 5 This wine cabinet is front venting The wine cabinet draws air from the rear and expels through the metal grid under the door at the front If a kick board is to be placed in front of the ventilation grid another grill must be fitted into the kick board with a minimum air flow allowance of 150cm2 6 This wine cabinet has a power switch located on the control panel so power point location is not critical 7 This wine cabinet requires a standard 240 volt 10 amp power point Or other according to each country specifications 8 The power cord is 1 9m in length and is fixed on the right side at the back when looking from front of cabinet 9 As with most appliances of today this wine cabinet has sensitive electronic components which are susceptible to damage through lightning and electricity supply faults It is therefore advised to use a power surge protector to avoid problems of this nature 10 Please s
3. see preset chart Most power failures are corrected within a short period of time An hour or two s loss of power will not affect your wine cellar s temperatures To avoid sudden change of temperature while the power is off you should avoid opening the door For longer period of power failure do take steps to protect your wine 20 Irrespective of the cause if you notice either abnormal temperature or humidity levels inside your wine cellar be reassured that only long and frequent exposure to these abnormal conditions can cause a detrimental effect on your wines TROUBLESHOOTING GUIDE Common problems may easily be solved saving you the cost of a possible service call Please read carefully the instruction manual and revert to troubleshooting guide chart PROBLEM POSSIBLE CAUSE Wine cellar does not operate Not plugged in The appliance is turned off The circuit breaker tripped or the fuse is broken Wine cellar is not cold enough Check the temperature control setting External environment may require a higher setting The door is opened too often The door is not closed completely The door gasket does not seal properly Turns on and off frequently The room temperature is hotter than normal A large amount of contents has been added to the Wine cellar The door is opened too often The door is not closed completely The temperature control is not set correctly The door gasket does not
4. 5 outward and take it out Fig 2 Remove the 3 bolts and take out the right top hinge 2 Fig 3 14 Fix the left top hinge and the bottom left hinge with the bolts as per Fig 4 Re install the door the same way it was removed and fix back the door axis V40 models 85mm recess plinth 1 Lower hinge Right 2 Lock screws 3 Top hinge Right 4 Lock Screws 5 Top hinge Left 6 Lower hinge Left 7 Door While holding the door firmly remove the three lock screws 2 from the lower right hinge module and remove it Fig 1 Remove the three lock screws 4 from the top right hinge and remove the hinge 3 Fig 3 Fix the top left hinge 5 at the top left corner with the three lock screws 4 Fig 4 While holding the door insert the axis core into the door s 7 upper left hinge s hole Fix the left bottom hinges by inserting the axis core first into the door s lower left hinge s hole 6 Then tie the lower left hinge to finish the door replacement Fig 5 15 V50 models SS SS 1 Lock screws 2 Lower hinge Right 3 Door axis 4 Top hinge Right 5 Door 6 Cabinet body 7 Top hinge Left 8 Lower hinge Left Remove the lock screws to untied the door axis at the bottom of the door Fig 1 While holding the door firmly pull the do
5. All wines mature at the same temperature which is a constant temperature set between 12 C to 14 C Only the temperature of d gustation wine appreciation varies according to the type of wines see Wine Serving Temperature Chart above This being said and as it is for natural cellars used by wine producers for long period of storage it is not the exact temperature that is important but its consistency In other words as long as the temperature of your wine cellar is constant between 12 C to 14 C your wines will be stored in perfect conditions Not all wines will improve over the years Some should be consumed at an early stage 2 to 3 years while others have tremendous ageing capability 50 and over All wines have a peak in maturity Do check with your wine merchant to get the relevant information 10 DEFROSTING CONDENSATION HYGROMETRY VENTILATION Your wine cellar is designed with Auto cycle defrost system During Off cycle the refrigerated surfaces of the wine cellar defrost automatically Defrost water from the wine cellar storage compartment drains automatically and part of it goes into a drainage container which is located at the back of the wine cellar next to the compressor The heat is transferred from the compressor and evaporates any condensation that has collected in the pan Part of the remaining water is collected within the wine cellar for humidity purposes This system enables the creation
6. Models V30SG e V40SG e V30SG 2e V40SG 2e V40DG 2e Capacity750ml 35 40 Upper 10 Upper 16 Left 19 Lower 20 Lower 22 Right 19 Net capacity 123L 150L 114L 140L 135L upper 6 upper 6 Right 12 Pre set temp in degrees 12 12 Lower 12 Lower 12 Left 7 upper 5 10 Upper 5 10 Right 5 18 Adjustable temp in degrees 3 to 18 5 to 18 Lower 10 18 Lower 10 18 Left 5 18 Power Input 87W 100W 87W 100W 107W Heater Yes Yes Yes Freestanding or Built in Freestanding Built in Freestanding Built in Built in N of wooden shelf 4 max 6 5 5 max 5 4 max5 12 Ambient temp in degrees 0 35 0 35 0 35 0 35 0 35 Climate Class T T T T T Net dim in mm WXDXH 493x588x840 595x572x820 493x588x840 595x572x820 595 573 820 Gross dim in mm WXDXH 550x650x880 655x665x875 550x650x880 655x665x875 655x665x875 Net weight 38kg 44 kg 43 kg Soke soke Gross weight 42 kg 48 kg 47 kg sake Sake Subject to changes accordingly to various references and models modifications Standard features Compressor operated R134a or R600a Available in rated voltage frequency as per country s requirements 100V 50 60Hz 220V 50 60Hz 115V S0Hz Automatic defrost Humidity 65 RH 10 RH Black outer and inner finish Internal light Adjustable feet x 4 Double glass door with 3rd acrylic layer Glass door opening stainless steel or alloy finish on option ref ss or al B
7. The thermostat will maintain the temperature inside the wine cellar within a 2 5 C range But the thermal inertia of the wine and the glass is such that within this temperature range the actual temperature of the wine will only fluctuate 0 5 C to 1 C Standard models MAX adjustable from 5 to 9 C NORMAL adjustable from 10 to 14 C MIN adjustable from 15 to 18 C To modify the pre set temperature of standard models Circumrotate the knob The knob mark is the temperature pre set area A clockwise turn sets a lower temperature An anti clockwise turn sets a higher temperature Electronic models V30 e model The TEMP SET LED displays the set temperature The DISPLAY LED displays the internal air temperature Control panel of V30SG e wine cellars POWER CC At LIGHT RUN C Vow TEMP SET DISPLAY To modify the pre set temperature of V30SGe models Adjust the desired cooling temperature by pressing the UP or DOWN buttons Each depression of the buttons will scroll through the available temperature settings in increments of 1 degree Celsius The temperature setting can be adjusted from 30 to 18 or 5L to 18 V40SG e V50SG e models V40DG 2e V50DG 2e models for each compartment The DISPLAY LED displays the internal air temperature The set temperature automatically appears by pressing either th
8. cellar after having it shut off for a long time there will be a few degrees variance between the temperature you have selected and the one indicated on the LED readout This is normal and it is due to the length of the activation time Once the wine cellar is running for a few hours everything will stabilize Important If the unit is unplugged power is lost or turned off wait 3 to 5 minutes before restarting the unit The wine cellar will not start if you attempt to restart before this time delay Operating Noises To reach the desired temperature settings VINTEC wine cellars like all wine cellars operating with compressors and fans may produce the following types of noises These noises are normal and occur as follows Gurgling sound caused by the refrigerant flowing through the appliance s coils Cracking popping sounds resulting from the contraction and expansion of the refrigerant gas to produce cold Fan operating sound to circulate the air within the wine cellar An individual s perception of noise is directly linked to the environment in which the wine cellar is located as well the specific type of models VINTEC wine cellars are in line with international standards for such appliance VINTEC will always do its utmost to satisfy its customers but will not retake possession of the goods due to complaints based on normal operating noise occurrences LOADING YOUR WINE CELLAR You may load your wine bottles in sing
9. ance In Queensland Australia the authorized person must hold a Gas Work Authorisation for hydrocarbon refrigerants before carrying out servicing or repairs which involve the removal of covers WARNING Keep ventilation openings in the appliance enclosure or in the built in structure clear of obstruction WARNING Do not use mechanical devices or other means to accelerate the defrosting process other than those recommended by the manufacturer WARNING Do not damage the refrigerant circuit WARNING Do not use electrical appliances inside the food storage compartments of the appliance unless they are of the type recommended by the manufacturer The environment and personal safety must be considered when disposing of this appliance Please ensure the appliance is taken to a recycle center for safe recycling DO NOT dispose of the appliance in land fill as the insulation and refrigerant gas contained in these appliances are flammable 25 Copyright All rights are reserved All photocopying reproduction translation whether partial or total are strictly prohibited without prior written consent from VINTEC www vintec cellar com
10. ased on carton box packing dimensions weight 24 R600A WARNINGS The following models use small quantity of R600A iso butane flammable refrigerant in their sealed system as follow AL V30SG e 30grams AL V30SG 2e 30grams AL V40SG e 35grams AL V40SG 2e 35 grams AL V40DG 2e 45grams For your safety observe the following recommendations e This appliance contains a small quantity of R600A refrigerant which is environmentally friendly but flammable It does not damage the ozone layer nor does it increase the greenhouse effect e During transportation and installation ensure that the tubing of the refrigerant circuit is not damaged e Avoid using or manipulating sharp objects nearby the appliances e Leaking refrigerant can ignite and may damage the eyes e In the event any damage does occur avoid exposure to open fires and any device which creates a spark Disconnect the appliance from the mains power e Thoroughly ventilate the room in which the appliance is located for several minutes e Notify Customer Service for necessary action and advice e The room for installing the appliance must be at least 1 cubic metre per 8 grams of refrigerant The refrigerant quantity contained in this appliance is listed above in grams it is also noted on the Rating Plate of the appliance It is hazardous for anyone other than an Authorised Service Person to carry out servicing or repairs to this appli
11. e UP or DOWN button Control panel of SG e and DG 2e model wine cellars o gt Ce 9 POWER 0 Aur FUN i Lier RUN V pown J DISPLAY To modify the pre set temperature of 40 50SGe and 40 50DG 2e models Adjust the desired cooling temperature by pressing the UP or DOWN buttons Each depression of the buttons will scroll through the available temperature settings in increments of 1 degree Celsius The temperature setting can be adjusted from 50 to 18 To visualize the set temperature press and hold the UP or DOWN buttons the set temperature will temporarily flash in the LED display for 5 seconds SG 2e models V30SG 2e V40SG 2e V50SG 2e The UPPER CHAMBER LCD displays the upper chamber internal air temperature The LOWER CHAMBER LCD displays the lower chamber internal air temperature 99 99 To visualize the set temperature press the corresponding button once the set temperature will temporarily flash in the LED display for 5 seconds Control panel of SG 2e model wine cellars iow CLS Power __ Set Upper O oe Light RUN Set Lower Upper chamber Lower chamber To modify the pre set temperature of SG 2e models Adjust the desired cooling temperature by pressing the Set Upper or Set Lower buttons Each depression of the buttons will scroll through the available temperature settings in inc
12. ee below detailed dimensional diagrams Please note The diagram below is for the 85mm plinth recess version 19 Dimensional drawings 3 625 7 632 Ais 605 _ a 602 i 3 7 NG y MS e y AA YUNG f iG Z Z i j ZA j j 7 7 7 j ZY ag Y ZAG Y 7 p A6 Yup 4 PE p Z f nE TESE j ZNG 7 j Y Y 7 Z UY 7 z 7 7 An Z wy j an LL _ JL 10 30 Front View Side View Top View OPERATION ANOMALIES Ensure that there is power to the electrical supply plug by connecting another electrical appliance to it Check fuse if any Make sure that the door is closed properly If your wine cellar appears to be malfunctioning unplug it and contact your VINTEC s after sales service Any intervention on the cold circuit should be performed by a refrigeration technician who should carry out an inspection of the circuit sealing system Similarly any intervention on the electrical circuit should be performed by a qualified electrician Notes Any intervention performed by a non technician will lead to the warranty being considered as null and void POWER FAILURES In the event of a power interruption all previous temperature settings are automatically erased and it will revert to a preset temperature setting
13. er Input 140W 140W 120W 140W 140W 120W 140W 140W 120W Heater Yes Yes Yes Yes Freestanding or Built in Freestanding Built in Freestanding Built in Built in Freestanding Built in Built in Built in N of wooden shelf 4 max 6 4 max 7 4 max 6 5 4 max 7 5 max 5 4 max5 4 max 6 14 Ambient temp in degrees 0 35 0 35 0 35 0 35 0 35 0 35 0 35 0 35 0 35 Climate Class T T T T T T T T T Net dim in mm WXDXH 493x588x840 605x605x875 493x588x840 595x572x820 605x605X875 493x588x840 595x572x820 605x605X875 605 602 875 Gross dim in mm WXDXH 550x650x880 680x725x935 550x650x880 655x665x875 680x725x935 550x650x880 655x665x875 680x725x935 675 685 910 Net weight 38 kg 52 kg 38 kg 44 kg 52 kg 43 kg 50 kg 55 kg 59 kg Gross weigh 42 kg 56 kg 42 kg 48 kg 56 kg 47kg 54kg 59 kg 63 kg 22 Standard features Compressor operated R134a or R600a Available in rated voltage frequency as per various country s requirements 100V 50 60Hz 220V 50 60Hz 115V 50Hz Automatic defrost Humidity 65 RH 10 RH Black outer and inner finish Internal light Adjustable feet x 4 Double glass door with 3rd acrylic layer Glass door opening stainless steel or alloy finish on option ref ss or al Based on carton box packing dimensions weight 23 R600a Technical data AL AL AL Al AL
14. erature for best enjoyment The upper chamber can hold 12 14 or 16 bottles depending on the models at a temperature of 5 C to 10 C dedicated mainly to white sparkling wines and champagnes The lower chamber accommodates 20 30 or 34 bottles depending on the models mainly for red wines which could be stored either at room temperature 18 C 20 C for consumption or at 12 C for a longer time of storage TEMPERATURE SETTINGS Important The LCD displays by default the actual internal air temperature The temperature settings are pre set at the factory as follows In the event of a power interruption all previous temperature settings are automatically erased and it will revert to the preset temperature settings Factory preset chart Model Setting Temperature V30 V50 SG Normal 10 C 14 C V30 V40 V50 SG e 12 12 C 2 5 C oe Upper compartment 6 6 C 2 5 C ANG vue ae Lower compartment 12 12 C 2 5 C acai Left compartment 12 12 C 2 5 C Vee ee Right compartment 7 7 C 2 5 C It is important to understand that there is a difference between the air temperature inside the wine cellar and the actual temperature of the wine You will need to wait approximately 12 hours before noticing the effects of temperature adjustment due to the critical mass within a full wine cellar Once the thermostat is set it is strongly advised not to toy with it or adjust frequently
15. le or double rows while taking note of the following if you do not have enough bottles to fill your wine cellar it is better to distribute the load throughout the wine cellar so as to avoid all on top or all below type loads Do remove or relocate adjustable wooden shelves to accommodate larger type of bottles or increase the capacity of the cellar by stacking the bottles up when necessary See removing shelves Keep smalls gap between the walls and the bottles to allow air circulation Like an underground cellar air circulation is important to prevent mould and for a better homogeneous temperature within the cellar Do not over load your wine cellar to facilitate air circulation Do not stack more than 1 5 rows of standard 0 75L bottles per shelves to facilitate air circulation Avoid obstructing the internal fans located inside on the back panel of the wine cellar Do not try to slide the shelves outwards beyond the fixed position to prevent the bottles from falling Do not pull out more than one loaded shelf at a time as this may cause the wine cellar to tilt forward Do not cover the wooden shelves with alloy foil or other materials as it will obstruct air circulation Do not move your wine cellar while it is loaded with wines This might distort the body of the wine cellar and cause back injury TYPES OF REGULATION Please note that depending on the loading and settings chosen it takes 24hours fo
16. ns are not completely understood If the supply cord is damaged it must be replace by a qualified person in order to avoid electrical hazard Installing your wine cellar Unpack and remove all of the protection and adhesive strips from the packaging around and inside the wine cellar The wine cellar must be positioned such that the plug is accessible Release the power cord Move your wine cellar to its final location The wine cellar should be installed in a suitable place where the compressor will not be subject to physical contact Leveling your wine cellar Wine cellar must be leveled BEFORE loading your wines Your Vintec wine cellar is equipped with 4 adjustable feet to facilitate easy leveling VINTEC recommends that you tighten the back feet to the maximum and adjust the front feet to create a level Back spacer Compressor run appliances require proper ventilation for proper and longer usage Your Vintec wine cellar is supplied with a back spacer Affixed the back spacer at the back of the cellar for air circulation and heat evacuation INSTALLATION OF BACK SPACER IMPORTANT THIS SPACER MUST BE ATTACHED TO THE UNIT BEFORE INSTALLATION FOR VENTILATION PURPOSE FAILURE TO DO SO VOIDS THE WARRANTY TURNING ON YOUR WINE CELLAR Plug in and switch on the cellar by pressing on the power button for a few seconds When you use the wine cellar for the first time or restart the wine
17. of changing the door we recommend that you get assistance Door is heavy and may cause injury if dropped According the model and the type of handle your wine cabinet is equipped with such as long strait bar handle the door might needs to be rotated for 180 degrees or changed for a right opening one V30 models 12 1 Rubber cover 2 Screw 3 Decorative cover 4 amp 7 Screw 5 Top hinge module 6 Door 8 Lower hinge module Left 9 Cabinet s leg short Pull out the screw covers and unscrew the decorative cover Fig 1 While holding the door firmly loosen and remove the top hinge lift up and remove the door See Fig 2 Unscrew the lower hinge 8 Remove the long cabinet leg 9 on the left side and shift it to the right end side Fig 3 Install the lower hinge and tie it with the bolts Install the door on the axe of lower hinge 8 the same way it was removed screw back the top hinge on the right Fix back the decorative cover and rubber cover 13 V40 models 30mm recess plinth 1 Lock screws 2 Lower hinge Right 3 Door axis 4 Top hinge Right 5 Door 6 Cabinet body 7 Top hinge Left 8 Lower hinge Left Unscrew the lock screws 1 Fig 1 to remove the door axis located at the bottom While holding the door firmly pull the door
18. of the correct humidity level inside your wine cellar required by the natural cork to maintain a long lasting seal Notes The water collected by condensation is therefore recycled Under extremely dry environmental conditions you may have to add some water into the water container provided with your wine cellar All units are equipped with a double glazed glass door that has a third internal acrylic layer to minimize condensation on the glass door The wine cellar is not totally sealed fresh air admission is permitted through the drainpipe Air is circulated through the cellar by means of a fan fans and the hollow shelves Notes During the refrigerating cycle heat is given off and disperse through the external surfaces of the wine cellar Avoid touching the surfaces during those cycles ADJUSTABLE WOODEN SHELVES Adjusting removing the shelves For easy access to the storage content you must pull the shelves approximately 1 3 of its depth out of the rail compartment These wine cabinets however are designed with a notch on each side of the shelf tracks to prevent bottles from falling V30 V40 amp V50 models When removing any of these shelves out of the rail compartment tilt the shelf as per the diagram and simply pull out or push in the shelf until it sits on the support brackets securely 11 REVERSIBILITY OF THE DOOR Warning To avoid accident during the process
19. or 5 outward take it out Fig 2 4 Remove the Right Top hinge Fig 3 Install the left top hinge and left lower hinge with bolts as per Fig 4 Put the door in position between the hinges and fix the door axes 3 onto the door 16 INSTALLATION INSTRUCTIONS AND DRAWINGS FOR BUILT IN PURPOSES A V30 models are free standing only Any built in voids the warranty V40 s Installation instructions 85mm recess plinth 1 Wine Cabinet dimensions Height 820mm 860mm 40mm adjustable feet Width 595mm Depth 571mm 2 This wine cabinet is not designed to be fully integrated behind a joinery door 3 Please note that a minimum cut out of 615mm is required to facilitate installation removal and servicing 4 This wine cabinet requires 10mm clearance on both sides and top 30mm clearance at the rear Where possible a ventilation grid should be installed in the 30mm clearance at the rear either in the sides top or back of the joinery Minimum grid size is 200mm x 40mm 5 This wine cabinet is front venting The wine cabinet draws air from the rear and expels through the metal grid under the door at the front If a kick board is to be placed in front of the ventilation grid another grill must be fitted into the kick board with a minimum air flow allowance of 150cm2 6 This wine cabinet has a power switch located on the control panel so power point location is not critical 7 This wine cabinet requires a standard 240 vol
20. r the wine cellar to see the temperature stabilizing During this time LED seems to move erratically in particular for 2e models It is a normal process This process occurs whenever the setting is modified and or whenever a large amount of bottles are added to the cellar Single temperature Maturing Storage wine cellars V30SG V40SG V50SG standard regulation V30SG e V40SG e V50SG e electronic regulation digital display Designed to store and mature all wines red white and sparkling These wine cellars reproduce the ideal conditions for wine storage at a constant recommended temperature of 12 C They can also be set to provide ideal serving temperature for full enjoyment of the wine s qualities Unless stated by the wine maker on the bottle VINTEC recommends 7 C for your champagne 12 C for whites and 18 C for reds Refer to Wine Service Temperature recommendation chart Two Compartment single temperature wine cellars 2 in 1 Wine Cellars V40DG 2e V50DG 2e electronic regulation digital display DG models are made of two independent compartments regulated independently as 2 single zone wine cellars Like the e models each compartment are adjustable from 5 C to 18 C Ideal for storage or mise en temperature The right temperature for optimum enjoyment Two Temperature Serving Wine Cellars V30SG 2e V40SG 2e V50SG 2e electronic regulation digital display Designed to store wines at the correct temp
21. rements of 1 degree Celsius The temperature selected will flash in the LED display for approximately 5 seconds and then revert to displaying the temperature of the internal cabinet The temperature setting can be adjusted from 50 to 100 in upper compartment and 100 to 180 in lower compartment WINE SERVING TEMPERATURE CHART All wines mature at the same temperature which is a constant temperature set between 12 C to 14 C The below chart is an indicative temperature chart to indicate the best temperature for drinking purposes Champagne NV Sparkling Spumante 6 C Dry White Semillon Sauvignon Blanc 8 C Champagne Vintage 10 C Dry White Chardonnay 10 C Dry White Gewiirztraminer Riesling Pinot grigio 10 C Sweet White Sauternes Barsac Montbazillac Ice Wine Late Harvest 10 C Beaujolais 13 C Sweet White Vintage Sauternes 14 C White Vintage Chardonnay 14 C Red Pinot Noir 16 C Red Grenache Syrah 16 C Red Vintage Pinot Noir 18 C Cabernet amp Merlot French Australian New Zealand 20 C Chilean Italian Spanish Californian Argentinean Vintage Bordeaux Room temperature not exceeding 20 C IMPORTANT INFORMATION ABOUT TEMPERATURE Your VINTEC wine cellar has been designed to guarantee optimum conditions for storing and or serving your wines Fine wines require long and gentle developments and need specific conditions in which to reach their full potential
22. s NOT recommended to use a multi socket or extension lead have a surge protector fitted to the electrical outlet away from the microwave Certain microwave ovens do not have wave interference shield When placed within a 1 meter vicinity of the wine cabinet they may affect the operation of the wine cabinet Notes V30 models are for free standing ONLY V40 models are built in type as per the drawings thereafter V50 models are partially built in MUST allow 1cm to side amp back clearance The wine cellar should be placed where the ambient temperature is between 5 C to 35 C If the ambient temperature is above or below this range the performance of the unit may be affected Placing your unit in extreme cold or hot conditions may cause interior temperatures to fluctuate The ideal range of temperature may not be reached See Climate Class at the end of this manual Grounding instructions The wine cellar must be grounded in case of an electrical short circuit Grounding reduces the risk of electrical shock The wine cellar is equipped with a power cord having a grounding wire and plug The wine cellar plug must be plugged into a properly affixed and grounded electrical outlet Note Jn locations where there is frequent lightning it is advisable to use surge protectors Improper use of the grounding plug can result in the risk of electric shock Consult a qualified electrician or service person if the grounding instructio
23. seal properly The light does not work Not plugged in The circuit breaker tripped or a blown fuse The bulb is out of order The light button is OFF Vibrations Check to assure that the Wine cellar is level The Wine cellar seems to make too much noise The rattling noise may come from the flow of the refrigerant which is normal As each cycle ends you may hear gurgling sounds caused by the flow of refrigerant in your Wine cellar Contraction and expansion of the inside walls may cause popping and crackling noises The Wine cellar is not level The door will not close properly The Wine cellar is not level The door was reversed and not properly installed The gasket is faulty magnet or rubber is spoiled The shelves are out of position 21 R134a Technical data Models V30SG V50SG V30SG e V40SG e V50SG e V30SG 2e V40SG 2e V50SG 2e V50DG 2e Capacity750ml 35 50 35 40 50 Upper 10 Upper 16 Upper 14 Left 21 Lower 20 Lower 22 Lower 34 Right 21 Net capacity 123L 161L 122L 150L 161L 114L 140L 151L 145L Normal Normal upper 6 upper 6 upper 6 Right 12 Pre set temp in degrees 10 14 10 14 12 12 12 Lower 12 Lower 12 Lower 12 Left 7 upper 5 10 Upper 5 10 Upper 5 10 Right 5 18 Adjustable temp in degrees 5 to 18 5 to 18 3 to 18 5 to 18 5 to 18 Lower 10 18 Lower 10 18 Lower 10 18 Left 5 18 Pow
24. t 10 amp power point Or other according to each country specifications 8 The power cord is 1 9m in length and is fixed on the right side at the back when looking from front of cabinet 9 As with most appliances of today this cabinet has sensitive electronic components which are susceptible to damage through lightning and electricity supply faults It is therefore advised to use a power surge protector to avoid problems of this nature 17 18 Height 874mm 880mm Width 605mm Depth 598 5mm Dimensional drawings V40 s 30mm recess plinth 77 75 y ee GJE J ff lt if DMi W W _ MOO X p a a a Na O N N T MQ G WG QY GG h WW D 7 ge K F 1 D i N J X D N X Ge jo a N Ne N w a gt N D Name N S N a N S I PR m E M T8 ae 7 i 028 III SSS A NN 3 A m IN K N i Sy i 1 ON N N a a a A p IA N NOS gT J ON Zz N nT i Q N I P N SII 7 BA SE ete a ge ae
Download Pdf Manuals
Related Search