Release Note
Contents
1. Negative VCC RJ 45 pin 3 6 Data 1 2 3 6 PoE Pin Assignment Per unit Power 1 Green Power 2 Green Fault Red Per port Link Activity Green Full duplex Collision Yellow PoE Feeding Power Green Lantech 10Base T 2 pair UTP STP Cat 3 4 5 5e cable EIA TIA 568 100 ohm 100m Network Cable 100Base TX 2 pair UTP STP Cat 5 5e cable EIA TIA 568 100 ohm 100m Redundant power DC 48V with connective removable Power Supply terminal block Power 3 4Watts without PoE 57 Watts Full load with PoE Consumption DIN rail kit for DIN type cabinet install and wall mount Installation ear for wall mounting 40 C to 75 C wide operating temperature model Operating Temp 10 C to 60 C standard model Operating n 5 to 95 Non condensing Humidity Storage 40 C to 85 C Temperature IP 30 30mm W x 95mm D x 140mm H FCC Class A CE EN61000 4 2 3 4 5 6 8 11 12 CE EN61000 6 2 CE EN61000 6 4 UL Safety cUL CE EN60950 1 IEC60068 2 32 Free fall Stability testing IEC60068 2 27 Shock IEC60068 2 6 Vibration2. above cable for 1000Mbps Also be sure that the length of any twisted pair connection does not exceed 100 meters 328 feet B Diagnosing LED Indicators To assist in identifying problems the Switch can be easily monitored through panel indicators which describe common problems the user may encounter and where the user can find possible solutions W f the power indicator does not light on when the power cord is plugged in user may have a problem with power cord Then check for loose power connections power losses or surges at power outlet If you still cannot resolve the problem contact the local dealer for assistance m f the Industrial switch LED indicators are normal and the connected cables are correct but the packets still cannot transmit Please check your system s Ethernet devices configuration or status Lantech Technical Specification The 5 10 100TX w 4 PoE Injector Industrial Switch technical specifications is shown as below IEEE 802 3 10Base T Ethernet IEEE 802 3u 100Base TX Fast Ethernet IEEE802 3x Flow Control and Back Pressure IEEE802 3af Power over Ethernet 14 880 pps for 10Base T Ethernet port 148 800 pps for 100Base TX Fast Ethernet port MAC Address 2K MAC address table Standard Transfer Rate 10 100TX 5 x RJ 45 with auto MDI MDI X function Connector Supports 4 PoE injector function RJ 45 port 1 4 support IEEE 802 3af End point Alternative A mode Positive VCC RJ 45 pin 1 2
3. this industrial switch support automatic MDI MDI X operation user can use straight through cables See figure below for all network connections to PCs or servers or to other switches or hubs In straight through cable pins 1 2 3 and 6 at one end of the cable are connected straight through to pins 1 2 3 and 6 at the other end of the cable The table below shows the 10BASE T 100BASE TX MDI and MDI X port pin outs Pin MDI X Signal Name MDI Signal Name 1 Receive Data plus RD Transmit Data plus TD 2 Receive Data minus RD Transmit Data minus TD 3 Transmit Data plus TD Receive Data plus RD 6 Transmit Data minus TD Receive Data minus RD 6 Lantech Switch Router or PC 3 TD 3 RD 6 TD 6 RD 1 RD 4 1 TD 2 RD 4 2 TD Straight Through Cable Schematic Switch Switch 3 TD 3 TD 6 TD 6 TD RD RD 2 RD 2 RD Cross Over Cable Schematic Cabling W Twisted pair segment can be connected with unshielded twisted pair UTP or shielded twisted pair STP cable The cable must comply with the IEEE 802 3u 100Base TX standard for Category 5 The cable between the converter and the link partner switch hub workstation etc must be less than 100 meters 328 ft long Lantech Wiring the Power Inputs Please follow the steps below to insert the power wire V V V V Insert the positive
4. Lantech IPES 0005T 4 5 10 100TX w 4 PoE Injector Industrial Switch User Manual V1 01 Nov 2007 Lantech FCC Warning This Equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy It may cause harmful interference to radio communications if the equipment is not installed and used in accordance with the instructions However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures W Reorient or relocate the receiving antenna m Increase the separation between the equipment and receiver W Connect the equipment into an outlet on a circuit different from that to which the receiver is connected W Consult the dealer or an experienced radio TV technician for help CE Mark Warning This is a Class A product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures Lantech Content IATFOGUCH ON pert 1 FOUE tse 1 P
5. ackage Content ccccceceeeeeeeeeeeeeeeeeeeeeeeeeeeeeeees 2 Hardware Description 3 Physical DiMensio cercen erede ee eb eR rts 3 ELODUD aNG scidit ceo Eod eiui que RE dads 3 FOD VIEW mE Rc T 4 LED IMGICAIOUS xisxasinstaseii wit hama MPa de opaadn ima EE Mer sade 5 doc 6 Capena C ES 7 Wiring the Power Inputs eeeeeseesessss 8 Wiring the Fault Alarm Contact 9 Mounting Installation 10 DIN Rail MOUNt NG eriein 10 Wall Mount Plate Mounting 12 Hardware Installation 13 Installation Steps esses 13 Network Application 14 Troubleshooting 15 Technical Specification 16 Lantech Introduction The 5 10 100TX w 4 PoE Injector Industrial Switch is a cost effective solution and meets the high reliability requirements demanded by industrial applications Besides the industrial switch provides the PoE function for kinds of Powered Devices to receive power as well as data over the RJ 45 cable Features m System Interface Performance RJ 45 ports support Auto MDI MDI X Function Embedded 4 port PoE Injection Store an
6. and negative wires into the V and V contacts on the terminal block connector Tighten the wire clamp screws for preventing the wires from loosing Lantech Wiring the Fault Alarm Contact The fault alarm contact is in the middle of terminal block connector as the picture shows below Inserting the wires it will detect the fault status including power failure or port link failure managed industrial switch only and form an open circuit An application example for the fault alarm contact is shown as below Insert the wires into the fault alarm contact Note The wire gauge for the terminal block should be in the range between 12 24 AWG Lantech Mounting Installation DIN Rail Mounting The DIN Rail is screwed on the industrial switch when out of factory If the DIN Rail is not screwed on the industrial switch please see the following pictures to screw the DIN Rail on the switch Follow the steps below to hang the industrial switch Rear Side DIN Rail 1 Use the screws to screw the DIN Rail on the rear side of the industrial switch 2 Toremove the DIN Rail reverse the step 1 Lantech 3 After the DIN Rail is screwed on the rear side of the switch insert the top of DIN Rail into the track 4 Then lightly push the DIN Rail into the track 5 Check if the DIN Rail is tightened on the track or not 6 To remove the industrial switch from the track reverse steps above Lantech Wall Mou
7. d Forward Switching Architecture Back plane Switching Fabric 1 0Gbps 2K MAC Address Table m Power Supply gt DC 48V Redundant Power W Case Installation gt P 30 Protection gt DIN Rail and Wall Mount Design Provides EFT protection 3 000 VDC for power line Supports 6 000 VDC Ethernet ESD protection VV VV V Lantech Package Contents Please refer to the package contents list below to verify them against the checklist mM 510 100TX w 4 PoE Injector Industrial Switch m User manual W Pluggable Terminal Block E 2 wall mount plates with screws Compare the contents of the industrial switch with the standard checklist above If any item is damaged or missing please contact the local dealer for service Lantech Hardware Description In this paragraph the Industrial switch s hardware spec port cabling information and wiring installation will be described Physical Dimension 5 10 100TX w 4 PoE Injector Industrial Switch dimension W x D x H is 30mm x 95mm x 140mm Front Panel The Front Panel of the 5 10 100TX w 4 PoE Injector Industrial Switch is shown as below i R Front Panel of the PoE Injectors Industrial Switch Lantech Top View The top view of the 5 10 100TX w 4 PoE Injector Industrial Switch has one terminal block connector of two DC power inputs V PWR2 1A 24V_ PWRI SA V2 VES ty Fault Top View of the PoE Injectors Industrial Switch Lantech LED Indicators The
8. diagnostic LEDs located on the front panel of the industrial switch provide real time information of system and optional status The following table provides the description of the LED status and their meanings for the switch LED Color Description On Power input 1 is active P1 Green Off Power input 1 is inactive On Power input 2 is active P2 Green Off Power input 2 is inactive On Power input 1 or 2 has failed Fault Red OH Power input 1 and 2 are both functional or no power inputs On The port is supplying power to the powered device FWD 1 4 Green Off No powered device attached or power supplying fails Green On Connected to network Upper Flashing Networking is active LED Off Not connected to network 1 5 RJ 45 Yellow On Full duplex link Lower Flashing Collision occurs LED Off Half duplex link or link down Lantech Ports B RJ 45 ports The UTP RJ 45 Fast Ethernet ports will auto sense for 10Base T or 100Base TX connections Auto MDI MDIX means that the switch can connect to another switch or workstation without changing straight through or crossover cabling See the below figures for straight through and crossover cable schematic W RJ 45 Pin Assignments Pin Number Assignment 1 TX 2 Tx 3 Rx 6 Rx Note and signs represent the polarity of the wires that make up each wire pair All ports on
9. f LED lights 5 Prepare the twisted pair straight through Category 5e above cable for Ethernet connection 6 Insert one side of the RJ 45 cable into the Industrial switch Ethernet port and another side to the network device s Ethernet port e g Switch PC or Server The UTP STP port RJ 45 LED on the Industrial switch will light up when the cable is connected with the network device Please refer to the LED Indicators section for LED light indication 7 When all connections are set and LED lights all show in normal the installation is complete Lantech Network Application This segment provides the sample to help user have more actual idea of industrial switch application For a sample application of the industrial switch see the figure below Control Center Core Upper Level Switch Fiber Cable Liles L e IEEE VOIP Phone IP Camera Wireless AP IEEE 802 3af Compliant Powered Devices Lantech Troubleshooting m Verify that is using the right power cord adapter DC 48V please don t use the power adapter with DC output voltage higher than 48V or it will burn this equipment down WB Select the proper UTP STP cable to construct your network Please check that is using the right cable Use unshielded twisted pair UTP or shield twisted pair STP cable for RJ 45 connections 100 Q Category 3 4 or 5 cable for 10Mbps connections 100 Category 5 cable for 100Mbps connections or 100 Category 5e
10. nt Plate Mounting Follow the steps below to mount the industrial switch with wall mount plate 1 Remove the DIN Rail from the industrial switch loose the screws to remove the DIN Rail Place the wall mount plate on the rear panel of the industrial switch Use the screws to screw the wall mount plate on the industrial switch Use the hook holes at the corners of the wall mount plate to hang the industrial switch on the wall To remove the wall mount plate reverse steps above Lantech Hardware Installation In this paragraph we are going to mention how to install the 5 10 100TX w 4 PoE Injector Industrial Switch and the installation points to be attended to it Installation Steps 1 Unpack the Industrial switch packing 2 Check if the DIN Rail is screwed on the Industrial switch or not If the DIN Rail is not screwed on the Industrial switch please refer to DIN Rail Mounting section for DIN Rail installation If user want to wall mount the Industrial switch then please refer to Wall Mount Plate Mounting section for wall mount plate installation 3 To hang the Industrial switch on the DIN Rail track or wall please refer to the Mounting Installation section 4 Power on the Industrial switch Please refer to the Wiring the Power Inputs section for knowing the information about how to wire the power The power LED on the Industrial switch will light up Please refer to the LED Indicators section for indication o
Download Pdf Manuals
Related Search