GSD Series DC Drives Accessories Overview
Contents
1. V4 installation and wiring information is included in the GSD4 DC Drives User Manual GSDA AI V5 For use with GSD5 240 10C open frame DC drives This option card allows for the use of either a grounded or non grounded remote DC signal such as 0 5 VDC through 0 250 VDC 4 20mA or a remote speed potentiometer The DC input signal type can be selected for voltage Vin or current 4 20mA and there is a Hi Lo range selection to select the voltage ranges The GAIN trim pot is used to set full linear output in reference to the input signal range The output of this remote signal isolation board is a linear signal that is proportional to the remote input signal being supplied GSDA AI V5 installation and wiring information is included in the GSD5 DC Drives User Manual Book 2 14 1 eDR 126 Dc Drives 1 800 633 0405 GSD Series DC Drives Accessories GSDA MREV For use with DC drives GSD3 all GSD4 all GSD5 240 10C open frame The GSDA MREV Manual Reversing Switch is a 4PDT 10A rated center blocked manual switch that can be used with IronHorse GSD series DC drives to manually reverse the direction of a DC motor When switched between the Forward and Reverse positions the blocked center position causes a delay which protects the DC drive from any voltage that may be on the motor armature terminals The center position is OFF NEUTRAL and is not connected to a wiring terminal Use the GSDA MREV switch to manually reverse a D2. fixed accel ramp built into the GSD4 drive providing independently adjustable linear acceleration and deceleration from 0 5 to 8 0 seconds Adjustments are made via two separate trim pots This option card plugs into the expansion connector on the GSD4 main circuit board GSDA ACCDEC 4 installation and wiring information is included in the GSD4 DC Drives User Manual GSDA AI A For use with DC drives GSD4 24x xC GSD5 240 10C GSD6 all open frame This option card is a 4 20 mA isolated analog current signal card that can replace the speed pot as a speed input signal to certain GSD series drives The 4 20 mA signal input can be either grounded or ungrounded The board sets on spacers screwed to the potentiometer HI Wiper and LO terminals on the main GSD drive board using screws included GSDA AI A installation and wiring information is included in the GSDA AI A DC Drives Accessory Data Sheet GSDA AI V4 For use with GSD4 240 xC 120 240V open frame DC drives This option card allows for the use of either a grounded or non grounded remote DC signal such as 0 5 VDC through 0 250 VDC 4 20mA current or a remote speed pot The DC input signal type can be selected for voltage Vin or current 4 20mA and there is a GAIN trim pot to set full linear output in reference to the input signal range The output of this remote signal isolation board is a linear signal that is proportional to the remote input signal being supplied GSDA AI
3. 1 a OR S2 Signal 1 P1 8 amp P1 9 signal inputs may be programmed ignal 2 O O for a number of functions Signa ou NO Alarm Output Normally Open D E C Alarm Output Common Eana M ou NC Alarm Output Normally Closed Programmable GSDA DP Dimensions in mm 5 00 1269 7 2 29 58 1 4 62 117 4 4 00 101 6 3 62 92 0 177 2X 90 14 0 89 45 0 93 6 22 5 PANEL CUTOUT Book 2 14 1 www automationdirect com drives DC Drives DR 129
4. C motor without damaging the drive PrSSSssSssscorpessssssesSsssspsSsSssssrss 4 O O O Pe een O e O e Oe O e i Switch Position OFF no wire terminal n U O O O Switch Position 2 GSDA HTSNK 4 For use with GSD4 xxx xC open frame DC drives Optional heatsink for open frame GSD4 xxx 1C and GSD4 xxx 5C DC drives only Increases the output current capability of GSD4 240 5C drives to 10A non UL applications only Dimensions in mm 4X RO 11 R2 8 4X 8X3 8 THREAD FORMING SHEET METAL SCREWS www automationdirect com drives Switch Position 1 Automation LT eH i Prices as of April 16 2014 Check Web site for most current prices Dimensions in mm Drives LNS 1 44 O me BON a 152 agg ee Ree i aR 15 32 32 THREAD 0 69 we os 11 9 Wega 00 48 a _ i 12X 6 32X3 16 BINDING HEAD 0 07 A 1 8 MOUNTING CUTOUT 6 20 157 5 l 1 38 a38 Book 2 14 1 DC Drives eDR 127 Prices as of April 16 2014 Check Web site for most current prices GSD Series DC Drives Accessories GSDA DP Standard Features For use with DC drives GSD1 all GSD3 24A xxx 12 24V GSD4 all e Microprocessor based design combines the ultimate in GSD5 all GSD6 all GSD7 all responsiveness and accuracy in one package The GSDA DP digital potentiometer is a compact Non volatile memory stores adjustable parameters e
5. Prices as of April 16 2014 Check Web site for most current prices LUTTE Direct GSD Series DC Drives Accessories GSDA Accessories for GSD Series DC Drives Selection amp Specifications Q GSDA Accessories for GSD Series DC Drives Model Description For Use With Speed Potentiometer Kit 5kQ accessory replacement Includes adjustment knob and g GSDA 5K 0 100 speed dial GSD all GSDA ACCDEC 4 Independent Accel Decel Adjustment Card Field installable GSD4 all Isolated Analog Current Signal Input Card GSD4 24x xC open frame GSDA AI A Range 4 20mA GSD5 240 10C open frame Field installable for open frame drives as shown GSD6 open frame Isolated Analog Voltage Signal Input Card GSDA AI V 4 Range 0 10V or 0 250V Field installable for open frame drives as shown GSD4 240 xC 240V open frame Isolated Analog Voltage Signal Input Card GSDA AI V5 Range 0 10V or 0 250V GSD5 240 10C open frame Field installable for open frame drives as shown GSD1 all Digital Potentiometer 120 240 VAC input Programmable Outputs any unipolar or GSD4 all bipolar voltage range based on input voltage up to 24VDC 12V 10V 0 5V 0 24V g GSDA DP etc NEMA 4X enclosure fits 1 8 DIN cutout Replaces analog potentiometers where GSDS all vibration repeatability or precision is a concern GSD6 all GSD all Manual Reverse Switch 4PDT rated at 10A Allows reversing by switching DC motor G
6. SD4 all GSDA MREV armature leads Center blocking prevents motor leads from reversing when motor is still turning in the previous direction GSD5 240 10C open frame GSDA HTSNK 4 25 00 Heatsink Increases the drive s output current rating GSD4 24x xC open frame NOTE All GSDA Accessories are RoHS compliant GSDA 5K For use with all GSD series DC drives The GSDA 5K is a replacement potentiometer kit that can be used with IronHorse GSD series DC drives to control the speed of a DC motor All GSD series DC drives include a speed potentiometer The kit includes 1 5KQ potentiometer 3 pigtail wiring leads 8 1 2 in 20 AWG 1 adjustment knob S wWitly 1 rae Ca MY o e liy v wW II N dj S b NY 2 Dimensions in mm 1 0 100 dial z e g 1 mounting nut and lock washer Wiring Connections MOUNTING CUTOUT SPEEDPOT HI CW WHITE SPEEDPOT WIPER RED o SPEEDPOT LO CCW ORANGE K _ A 0 16 0 44 04 0 iii2 Book 2 14 1 www automationdirect com drives DC Drives DR 125 Prices as of April 16 2014 Check Web site for most current prices GSD Series DC Drives Accessories GSDA ACCDEC 4 For use with all GSD4 DC drives The GSDA ACCDEC 4 option card overrides the
7. ng Humidity Range 95 non condensing Regulatory Agency Approvals RoHS Book 2 14 1 eDR 128 DC Drives 1 800 633 0405 Prices as of April 16 2014 Check Web site for most current prices Automation GSD Series DC Drives Accessories GSDA DP GSDA DP Mounting amp GSDA DP Operation Modes Rate and Time mode cycle times operate E inversely from each other Rate Mode Unipolar Output N PANEL MOUNTING GASKET 100 CUSTOMER TH THE ADHESIVE SIDE OF ASKET FACING THE GUSTOMER 80 HOLE CUT OUT FOR CONTROL a HOUSING APPROXIMATELY 2 3 622 WIDE BY 1 770 HIGH 5 60 O a A 40 A Mm 20 2 0 0 1 2 3 4 5 GSDA DP Setting Time Mode Unipolar Output 100 00 S SUPPLIED WITH EACH CONTROL 80 00 1 GASKET 2 2 2 6 32 X 3 4 PANHEAD BLACK OXIDE STAINLESS SCREWS 3 60 00 3 2 6 NUT WITH LOCKWASHER A 40 00 5 a 20 00 2 00 00 0 1 2 3 4 5 GSDA DP Setting min sec GSDA DP Wiring GSDA DP AN IN AC INPUT 85 265 VAC O L SAUF fuse both lines for OF HI O AC INPUT system without neutral D Q E Q W iral Connect to the Speedpot or Analog 5 D WIPER or ANALOG VOLTAGE SIGNAL Voltage Input of the control being driven 5 om LO POT LO or V REF COM High must be positive voltage with respect to low z ou COM a ST esv a Supply 5V 50mA OF 5VDC
8. rating ambient temperature range of 10 C to 45 C 144 F to 113 F e Multiple operating modes including Rate Mode Displays in rate and non rate units such as rpm gallons per second and percent Time Mode Displays in time units such as HH MM MM SS SS TT or other units Rate and Time Modes operate inversely from each other GSDA DP Specifications Line Input Voltage 85 265 VAC Line Input Frequency 48 62 Hz Display Range 0 001 9999 Units of Operation User Programmable any Unit Onboard Power Supply externally accessible 5V 50mA Pot Lo Hi Supply VDC Range external supply 0 2 VDC through 0 24 VDC Pot Wiper VDC Range Pot Lo 50mV through Pot Hi 50mV Pot Circuit Current Draw 2mA 12V Pot Circuit Isolation gt 500 MQ Isolated Alarm Relay Output Ratings 250VAC 5A Form C Resolution of D A Converter 10 bits Electrical Analog Output Any unipolar or bipolar voltage range based on input voltage up to 24VDC Display Type LED Red 4 Digit 1 2 in Height Housing Type with supplied gasket in NEMA 4X panel 1 8 DIN NEMA 4X Connector Style 12 position 5mm European Style Mechanical Terminal Block Torque Setting 4 4 b in Max 0 5 N m Faceplate Material Polycarbonate with GE Lexan Overlay Housing Material Aluminum Weight 14 4 oz 408 229 Operating Temperature Range 10 C to 45 C 14 F to 113 F Environmental aE i Operati
9. ven when microprocessor based unit capable of being either field or power has been removed factory contigured for a number of industrial user intertace e Adjustable parameters include display range output range control signal needs The GSDA DP allows the user to adjust output polarity alarm options etc the displayed value via the tront panel push buttons As the Internal program enable jumper selectively prevents tampering displayed value is raised or lowered the output signal trom with unit s configuration the GSDA DP follows proportionally according to the unit S e Universal power supply accepts line voltages inputs from configuration These units support both unipolar and bipolar 85 265 VAC 50 60Hz without switches or jumpers The unit output and are capable of automatically inverting scaling and automatically adjusts as needed offsetting the output as needed The GSDA DP series is ideal for volume OEM applications requiring specialized inputs and outputs e Transient voltage protection prolongs unit s life in harsh industrial environments Self contained power supply for external sensor limited to 5V The GSDA DP durable 1 8 DIN aluminum housings can be 50mA easily mounted in a panel or control cabinet 1 8 DIN durable aluminum housing for panel mounting e Large 4 digit 1 2 LED display G E Lexan membrane and gasket which are included meet NEMA 4X standards when used with NEMA 4X enclosures e Wide ope
Download Pdf Manuals
Related Search