English - Hansol
Contents
1. FCC Information This equipment has been tested and found to comply with limits for a class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment can generates uses and radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful inteference to radio Communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause unacceptable interference to radio and television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures m Reorient or relocate the receiving antenna m Increase the separation between the equipment and receiver m Connect the equipment into an outlet on a circuit different from that to which the receiver is connected m Consult the dealer or an experienced Radio TV technician for help DECLARATION OF CONFORMITY PRODUCT NAME 17 COLOR MONITOR MODEL NUMBER E17CL FCC RULES TESTED TO COMPLY WITH FCC PART 15 CLASS B OPERATING ENVIRONMENT FOR HOME OR OFFICE USE FCC COMPLIANCE STATEMENT This device complies with part 15 of FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interfer2. 02 Pixel rate MHz 78 750 94 5 107 761 30 24 57 284 H Polarity Positive Positive Positive Negative Negative V Polarity Positive Positive Positive Negative Negative 14 Users Manual
3. marking label Slots and openings in the cabinet are provided for ventilation these openings must not be blocked or covered Never push objects of any kind into cabinet slots or other openings m Never insert anything metallic into the monitor openings Doing so may create a danger of electric shock To avoid electric shock never touch the inside of the monitor Only a qualified technician should open the monitor s case m Unplug the monitor from the wall outlet before cleaning Do not use liquid cleaners or aerosol cleaners Use a damp lint free cloth for cleaning a Install the monitor near an outlet that you can reach easily Disconnect the product by grasping the plug firmly and pulling in from the outlet Never disconnect it by pulling the cord 4 User s Manual Introduction Features Superior image m On Screen menu fingertip control system to visually select and adjust screen using buttons on front panel and on screen menus m The exclusive double dynamic focus system with a hyperbolic focus compensation circuit controls the electron beams resulting in a fine image display over the entire area of the screen JOEPIE m Super contrast screen for superior contrast and richer color m Advanced INVAR Shadow mask for superior focus brightness and color a 17 0 27dot pitch high resolution non interlaced technology provides sharp flicker free images m On screen menu color control system easil
4. the Macintosh system please contact an authorized dealer Need to use a special adaptor Pin assignment table D Sub Mini 15pin connector Pin No ANooakR WDM staat ta o aK WBNM 0O0 Assignment Red Video Green Video Blue Video Frame Ground Ground Red Video Ground Green Video Ground Blue Video Ground N C Sync Ground Ground SDA H Sync V Sync SCL JOEPIE 1 Insert the AC power cord into monitor and then into an AC power outlet 2 Connect the signal cable to the 15pin graphics connector of the system and tighten the fastening screws 3 To turn on the monitor push the power The 15 pin D Sub connector male of the signal cable IBM Systems 11 15 15 Pin D Sub User s Manual 7 Controls m OSD controls ON SCREEN MENU controls include the following extended controls such as Size Position Geometry Color Adjust Brightness and Contrast Utilities Adjustments are saved instantly The currently addressed control can be reset to factory settings by pressing the Reset button Oa o 0 Function of OSD buttons on the front of the monitor m In the main menu exits the OSD controls In a submenu exits to the OSD main menu a 1 When no OSD on the Screen Direct access to Brightness controls Direct access to Contrast controls 2 When Main menu is displayed Moves to function what you want to adjust 3 When the Sub m
5. the right in the selected selected unction function Toggles horizontal or Shinks the Expands the Exit to No 2 vertical size image in the image in the selected selected unction function Odd press Controls the amount of the Exit to No 2 Selects and blinks the Selected funcion Refer to Geo a function with RED ICON metry controls menu in detail TRAPEZOID Even press Moves to function you want Exit to No 2 PINBALANCE Stops blinking and ready to move function you want User s Manual 9 HSIISNA Controls Controls OSD MENU MENU Z m 13 ZOOM Odd press Shinks the Expands the Exit to No 1 Z m Selects zoom and image image e blinks the zoom ICON horizontally horizontally m a u o S and vertically and vertically N w O OAA I o Even press Stops blinking and ready to move anther function Moves to the function you want Exit to No 1 OSD MENU MENU 2 8 MOIRE Odd press Contros the amount of selected Exit to No 2 os Selects and blinks the function Please control these key function with RED ICON in order the image not to shiver gt H MOIRE ADJUST V MOIRE ADJUST Even press Moves to function you want CTT TT Stops blinking and ready to move function you want 9 LANGUAGE Selects the languages Moves to language you want Exit to No 2
6. Equipment Regulations Avis Canadien Cet appareil num rique de la classe B respecte toutes les exigences du R glement sur le mat riel brouilleur du Canada Notice The information contained in this document is subject to change without notice User s Manual 3 Introduction Package Congratulations on your purchase of this top quality color monitor The items illustrated below are contained in the carton First be sure that your carton includes all of them If any items are missing or damaged please contact your local dealer or supplier Css MaRS mid Display Monitor AC Power Input Cable m Safety information Provided with this monitor is a detachable power supply cord with IEC320 style terminations It may be suitable for connection to any UL listed personal computer with similar configuration Before making the connection ensure that the voltage rating of the computer convenience outlet is the same as the monitor and that the ampere rating of the computer convenience outlet is equal to or exceeds the monitor current rating For 120Volt applications use only UL listed detachable power cord with NEMA configuration 5 15P type parallel blades plug cap For 240Volt applications use only UL listed detachable power cord with NEMA configuration 6 15P type tandem blades plug cap m Use only a power source and connection appropriate for the monitor as indicated on the
7. TEES with RED ICON and E ENGISH Exit to No 2 EE 10 OSD POSITION Toggles OSD position Moves the OSD Moves the OSD Exit to No 2 horizontally or vertically menu left or menu right or OSD HPOSITION down in the up in the selected selected function function 11 COLOR MODE Odd press Moves to color mode you want Exit to No 1 ane Blinks the RED ICON and the selected color mode color menu ICON will blink Hike bd wos aaa O KET G Even press Moves to function you want Exit to No 1 500K 930K Stops blinking and ready to move function you want When the color mode a ICON is blinking in user mode press then go to color adjust mode No 12 12 COLOR ADJUST Odd press Controls the amount of function Exit to No 11 MODE Selects and blinks the you want ae co ae ne Gaba function you want Even press Moves to the function you want Exit to No 11 RB Red background raster GB Green background raster BB Blue background raster RG Red level gain GG Green level gain BG Blue level gain Stops blinking and ready to move function you want 10 Users Manual a Recall OCK a Degauss Q A Caution x Geometry Controls Menu GEOMETRY PINCUSHION PARALLELOGRAM TRAPEZOID PINBALANCE ROTATION m Pincushion m Parallelogram m Trapezoid m Pin Balance m Rotation Recall control to the factory setting resets all the controls within
8. ence and 2 this device must accept any interference received including interference that may cause undesired operation THE PARTY RESPONSIBLE FOR PRODUCT COMPLIANCE HANSOL MULTITECH INC 7001 VILLAGE DRIVE SUITE 255 BUENA PARK CA 90621 USA TEL 714 562 5151 User s Manual Introduction Package axes Safety Information Features shacenhgitcs Power management systemi ONAA Installation Connection to your personal computer s seeeesee seeen 7 Pin assignment table D sub mini 15 pin connector 7 Controls OSD Controls tes spams ene ete Troupesngotng No picture sidi Image is scrolling or unstable Picture is fuzzy sis ideas Picture bounces or a waving pattem i is 5 presenti in nthe picture reee 12 Edges of the display image are not square sses seers 12 Display image is not centered too small or too large 12 Specifications Electrical Specifications seeee eseese cee ceeeee eee cee eee nee ceenes 13 Mechanical specifications 13 Environmental specifications see eeeseesseeeeeee eee eee 13 Appendix Preset Timings seesee eee eee cee teense ee eee neeaeeeeenseeee eneee 14 Caution Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment Canadian Notice This Class B digital apparatus meets all requirements of the Canadian Interference Causing
9. enu allows the display unit to be checked on screen without connecting to a computer m Compact case minimizes desktop space giving you a large screen image without loss of workspace a Power cable included easily plugs into a standard outlet m Power management system This monitor complies with VESA Nutek and Energy Star power saving requirements The power saving system works only when used with VESA DPMS compliant PC s and or graphic controllers State LED Power Recovery Time On Green Normal 75 Watts N A Stand by Green lt 60 Watts lt 2Sec Suspend Amber lt 15 Watts lt 5Sec Off Amber Blink lt 5 Watts lt 15 Sec The monitor goes into various power saving stages depending on the incoming video signal as shown in the following table State Horizontal Sync Vertical Sync On On On Stand by Off On Suspend On Off Off Off Off Note 6 Users Manual The monitor automatically goes through the DPMS steps when it is idle To release the monitor from the DPMS condition press any key on the keyboard or mouse Installation Connection to your computer A CAUTION Ensure that both the PC and the display monitor are switched off To attach the monitor to your system as shown in the following illustrations Note To attach the monitor to
10. enu is displayed Controls the amount what you want to adjust a MENU Displays OSD main Menu 1 When Main menu is displayed Selects function with RED ICON 2 When Sub menu is displayed Selects function with RED ICON Additional front controls m Power Switch Turns the monitor power on or off When the power is on the LED is on a LED Power indicator Light Located left side of the power switch and indicates the monitor s power mode Each mode reduces the amount of power used by the monitor Accessing on screen menu Press MENU Button Turning off on screen menu When in the main menu press button When in submenus press button twice 8 Users Manual Controls m OSD Menu OSD MENU MENU 1 NO OSD Proceeds to NO 2 Proceeds to Proceeds to No meaning NO 3 NO 4 2 MAIN MENU The function with RED Moves to function you want Exit to No 1 POSITION ICON is Performed Recall SIDI LIS Ft Degauss aaa amp 1K EF Selected and blinked MESLE EY Color Adjust Zoom Proceeded Others 3 BRIGHTNESS Moves to No 2 Decreases the Increases the Exit to No 1 ER brightness brightness X BRIGHTNESS 4 CONTRAST Moves to No 2 Decreases the Increases the Exit to No 1 EET contrast contrast CONTRAST 5 HNV POSITION Toggles horizontal or loves the Moves the Exit to No 2 vertical position image down or image up or H POSITION z x a eft in
11. er s Manual Specifications m Electrical Specifications m ITEM E17CL 5 CRT Type 177 90 deflection FST _ CRT Dot pitch 0 27mm S CRT Surface Non glare H V Separate TTL positive negative Input eres HM Composite TTL positive negative Signal RGB Analog 0 7Vp p positive Video 75 Q Terminated Scanning Horizontal 30kHz 72kHz Automatically frequency Vertical 47Hz 160Hz Automatically Maximum Resolution 1280Dots x 1024Lines Non interlace Pixel Clock Max 110 MHz Display Size Standard Horizontal 306mm Vertical 230mm Power Consumption Max 85 Watts Power Supply AC 100 240Volt 50 60Hz 3Hz Input Connector D Sub 15Pin Connectors Display Colors Unlimited Mechanical Specifications ITEM E17CL Unit 16 5 W x 16 57 D x16 47 H 418mm W x419mm D x417mm H EDARAN 20 9 W x20 0 D x18 2 H Carton ee coe 530mm W x 508mm D x 462mm H Net Weight 34 0lbs 15 4Kg Gross 40 1lbs 18 2Kg Environmental Specifications ITEM E17CL Operating 32 F to 104 F 0 C to 40 C Temperature Storage 4 F to 140 F 20 C to 60 C Humidity 10 to 85 R H Non condensing User s Manual 13 Appendix m Preset Timings This Monitor E17CL has preset modes for the 10 most popular industry standards for Plug and Play capability Horizontal Video Ver
12. r for bent or pushed in pins m Press a key on the keyboard or move the mouse in case the screen power saver mode has blanked the screen m Image is scrolling or unstable a Signal cable should be securely attached to the computer a Check the pin assignments and signal timings of the monitor and your video card with respect to recommended timings and pin assignments a Ensure that the video card is securely seated in the PC m Picture is fuzzy m Adjust the Contrast and Brightness Controls m Push the Degauss Button once h Caution A minimum interval of 20 minutes should exist before the Degauss Button is used a second time Do not hold the button down continuously m Picture bounces or a waving pattern is present in the picture a Move electrical devices that may be causing electrical interference away from the monitor See the inside front cover of this manual for FCC information m Unshielded audio speakers placed next to the monitor can cause picture distortion Move the speakers away Edges of the display image are not square a Adjust the distortion using the Side Pincushion or Trapezoid Pincushion Balance Parallel adjustment controls under the on screen menu m Display image is not centered too small or too large a Adjust the horizontal and vertical image sizes using the Horizontal and Vertical Size adjustment controls under the on screen menu 12 Us
13. the all menu Please allow aminimum of 20 minutes to elapse between uses of the Degauss Increases or decreases the curvature of the sides either inward or outward Increases or decreases the bottom of the screen to be the same as the top Increases or decreases the curvature of the sides either to the left or right Increases or decreases the tilt of the screen image relative to a horizontal line If you want to return to the factory mode setting press Recall key 5 8 Sec continuously Eliminates the build up of stray magnetic fields which alter the correct scan of the electron beams and affect the purity of the screen colors focus and convergence When pressed you screen image will jump and waver a bit as the screen is demagnetized button Do not hold the button down continuously to avoid decreasing the life the Deguass circuitry The Geometry controls allow you to adjust the curvature or angle of the sides of you display Increases or decreases the tilt of the sides either to the left or right User s Manual 11 Troubleshooting m No picture m Check that the AC cord is correctly connected m Check that the AC socket is live by plugging in another piece of equipment m Power switch and computer power switch should be in position a Ensure that the signal cable is properly connected to the video card or PC a Ensure that the video card is securely seated in the PC m Check the connecto
14. tical B a eee Resolution IBM VESA VGA 70Hz VGA 60Hz 640 85Hz 800 75Hz 800 85Hz Timing 720 x400 640 x 480 640 x 480 800 x 600 800 x 600 H Freq kHz 31 469 31 469 43 269 46 875 53 674 Apsec 31 777 31 777 23 111 21 333 18 631 Bysec 3 813 3 813 1 556 1 616 1 138 C sec 1 907 1 907 2 222 3 232 2 702 D sec 25 422 25 422 17 778 16 162 14 222 Eysec 0 636 0 636 1 556 0 323 0 569 V Freq Hz 70 09 59 94 85 008 75 85 061 Omsec 14 268 16 684 11 764 13 333 11 756 Pmsec 0 064 0 064 0 069 0 064 0 056 Qmsec 1 08 1 048 0 578 0 448 0 503 Rmsec 12 711 15 253 11 093 12 8 11 179 Smsec 0 413 0 318 0 023 0 021 0 019 Pixel rate MHz 28 322 25 175 36 49 5 56 25 H Polarity Negative Negative Negative Positive Positive V Polarity Positive Negative Negative Positive Positive Resolution VESA MACINTOSH 1024 75Hz 1024 85Hz 1280 60Hz 640 67Hz 832 75Hz Timing 1024 x768 1024 x 768 1280 x 1024 640 x480 832 x 624 H Freq kHz 60 023 68 677 63 953 35 49 726 Asec 16 660 14 561 15 636 28 571 20 11 B sec 1 219 1 016 1 018 2 116 1 117 C sec 2 235 2 201 2 255 3 175 3 91 D sec 13 003 10 836 11 636 21 164 14 524 Esec 0 203 0 508 0 727 2 116 0 559 V Freq Hz 75 029 84 997 59 938 66 667 74 551 Omsec 13 328 11 765 16 684 15 13 414 Pmsec 0 050 0 044 0 078 0 086 0 06 Qmsec 0 466 0 524 0 579 1 114 0 784 Rmsec 12 795 11 183 16 012 13 714 12 549 Smsec 0 017 0 015 0 016 0 086 0
15. y allows the white of the image to be adjusted as well as R G B signals resulting in true to life colors Ergonomic Design m Flat square screen to reduce image distortion and glare thus relieving eye strain a Tilt base allowing 90 rotation in the horizontal and 17 in the vertical for greater user comfort m Low leak radiation prevention meeting MPR Land the very stringent TCO option magnetic field emissions standards for increased user safety Environmentally Friendly m Power management circuit conforming to VESA DPMS standards controls energy consumption when monitor is not in use you save energy a All plastic parts are recyclable All materials are strictly selected to ensure ease of maintenance inspection and disposal Timing a Automatic tracking of horizontal frequencies of 30 to 72 kHz and vertical frequencies of 47 to 160 Hz m Ten timings are factory preset for image size and position a Ten additional timings are user definable Synchronizing input signals separate composite can be automatically selected User s Manual 5 Introduction System Flexibility a Equipped with DDC1 DDC2B and DDC2Bi for Plug amp Play compatibility a Monitor is compatible with VGA SVGA VESA and high resolution video modes up to 1280 H x 1024 V 60Hz a Monitor may be used with IBM or compatible PC MAC a Automatic universal power supply is built in permitting AC power input of 100 240V AC 50 or 60HZz a Self test m
Download Pdf Manuals
Related Search