S550-MFW1U User`s Manual
Contents
1. CR delay circuit or constant current load circuit is less than dozens of pA Execute the same procedure as Note 2 when it is CMOS output Note 8 The Vss terminal should be connected since it is signal ground Please combine with this example of a connection circuit and confirm a Hardware manual or a Data sheet of each microcomputer Multifunctional Flash Microcomputer S550 MFW1U 23 Operation Manual 3 M16C 80 Series ROM external version Note 1 Note 2 Note 3 Note 4 Note 5 Note 6 Target board prepared by user MCU peripheral circuit RESET Vss Serial cable CE GND CNVss BUSY TXD EPM RESET RXD MFW1U unit Diagram 3 Power supply of the MFW1U for serial programming is provided by a user target board via Vcc pins Connect the power of the board to the Vcc terminal directory Attach the AC adapter to supply power when the current capacity of the target board is insufficient since the maximum current consumption of the MFW1U for serial programming is 200mA Usage of Vcc should be 3 3V 5 or 5V15 Isolate TXD RXD SCLK and or BUSY terminals from the MCU peripheral circuit by jumper analog switch three state etc when serial programming is achieved Isolation can be omitted when those signal statuses are output from the MCU peripheral circuit Resistance should be 4 7KQ or over when pull up is achieved to these signals Connect the MCU CNVss terminal to Vss of the use2. All the settings are stored at the MFW1U unit at the time of termination of the PC control software mfwl exe Therefore when Erase Program or Verify is desired please make sure the Action setting is set to Erase Program and Verify before termination Not connect a USB cable when standalone serial programming by the MFW1U Multifunctional Flash Microcomputer S550 MFW1U Operation Manual 16 4 6 Standalone Onboard Programming Connection instructions for standalone serial programming by the MFWI1U after downloading data from PC to a user target board is illustrated below DC Cable for Oversea j y Ji Serial cable Connector at the serial adapter side shuold be prepared by user Aul aar TARI MFW1U unit DC power for board Usage should be Vec 3 3V Target board Vee 5 or 5V Prepared by user Standalone serial programming is available unless data update is occurred since downloaded data from PC to the MFW1U such as lock bit data and several settings retains at the MFW1U even if the power switch is turned OFF Simple operation for everyone without a complicated setting to PC is available by selecting Power supply of the MFW1U for serial programming is provided by a user target board via Vcc pins Attach the AC adapter to supply power when the current capacity of the target board is insufficient since the maximum current consumption of the MFW1U for serial programming is 200mA All
3. Up to 8 parallel adapters can be connected and programmed at once gang programming Devices to be gang programmed should be the same type in order to avoid breakage of devices Beware that the power of the MFW1U is OFF when attaching parallel adapter s Not connect a USB cable when standalone parallel programming by the MFW1U Multifunctional Flash Microcomputer S550 MFW1U 15 Operation Manual 4 5 Standalone Serial Programming Connection instructions for standalone serial programming by the downloading data from PC to a serial adapter is illustrated below DC Cable for Oversea Serial cable Connector at the serial adapter side shuold be prepared by user ne Sa MFW1U unit Serial adapter MFW1U after Standalone serial programming is available unless data update is occurred since downloaded data from PC to the MFW1U such as lock bit data and several settings retains at the MFW1U even if the power switch is turned OFF Simple operation for everyone without a complicated setting to PC is available by selecting Power supply to the serial adapter for serial programming is provided by the MFW1U via Vcc pins Particular power supply is not required A serial adapter can be prepared by obtaining the IC socket type programming board made by Renesas Electronics Some modification to the board is needed since the board mounts Vcc3 3V 5V switch circuit Please contact Sunny Giken Inc before operation
4. i Add New Hardware Wizard Dialog will be displayed Press Next Found New Hardware Wizard Welcome to the Found New gt Hardware Wizard This wizard helps you install a device driver for a hardware device To continue click Next ii Select Search for a suitable driver for your device recommended and press Next Found New Hardware Wizard Install Hardware Device Drivers A device driver is a software program that enables a hardware device to work with S an operating system This wizard will complete the installation for this device oy S550 MPW1U A device driver is a software program that makes a hardware device work Windows needs driver files for your new device To locate driver files and complete the installation click Next What do you want the wizard to do Display a list of the known drivers for this device so that can choose a specific driver lt Back Cancel Multifunctional Flash Microcomputer S550 MFW1U 48 Operation Manual iii Select Specify a location and press Next Found New Hardware Wizard Locate Driver Files ES Where do you want Windows to search for driver files y fi Search for driver files for the following hardware device o S550 MFW1U The wizard searches for suitable drivers in its driver database on your computer and in any of the following optional search locations that you specify To start the sear
5. Note 2 when it is CMOS output Note 6 The Vss terminal should be connected since it is signal ground Please combine with this example of a connection circuit and confirm a Hardware manual or a Data sheet of each microcomputer Multifunctional Flash Microcomputer S550 MFW1U 30 Operation Manual 9 M16C 26A M16C 28 M16C 29 Group Target board prepared by user MCU peripheral circuit Serial cable Vec CLK CE GND CNVss BUSY TXD EPM RESET RXD MFW1U unit Diagram 9 Note 1 Power supply of the MFW1U for serial programming is provided by a user target board via Vcc pins Connect the power of the board to the Vcc terminal directory Attach the AC adapter to supply power when the current capacity of the target board is insufficient since the maximum current consumption of the MFW1U for serial programming is 200mA Usage of Vcc should be 3 3V 5 or 5V15 Note 2 Isolate TXD RXD SCLK and or BUSY terminals from the MCU peripheral circuit by jumper analog switch three state etc when serial I O programming is achieved Isolation can be omitted when those signal statuses are output from the MCU peripheral circuit Resistance should be 4 7KQ or over when pull up is achieved to these signals Note 3 Execute the same procedure as Note 2 for CE P16 and RP terminal Connect CE terminal to CE of MFW1U or connect P16 terminal to CE of MFW1U and connect RP terminal to EPM of MFW1U Or only isolation process by
6. maximum current consumption of the MFW1U for serial programming is 200mA Usage of Vcc should be 3 8V 5 or 5V 5 Note 2 Isolate TXD RXD SCLK and or BUSY terminals from the MCU peripheral circuit by jumper analog switch three state etc when serial I O programming is achieved Isolation can be omitted when those signal statuses are output from the MCU peripheral circuit Resistance should be 4 7KQ or over when pull up is achieved to these signals Note 3 Execute the same procedure as Note 2 for CE terminal Or only isolation process by achieving pull up without the MFW1U connection is also applicable On board direct fix is also available of the CE terminal for H level when these terminals are not connected Note 4 Execute the same procedure as Note 2 for SEL terminal Or only isolation process by achieving pull down without the MFW1U connection is also applicable On board direct fix is also available of the SEL terminal for L level when these terminals are not connected Note 5 Connect the MCU CNVss terminal to the CNVss terminal of the MFW1U unit by achieving pull up down with resistance of 4 7KQ H level fixation by jumper switching is also available Attachment to the MFW1U is not needed for this case Note 6 Connect the reset terminal of the user target board MCU to the RESET terminal of the MFWI1U directly when the reset circuit of the user target board is open collector output CR delay circui
7. 5 Isolate TXD RXD SCLK and or BUSY terminals from the MCU peripheral circuit by jumper analog switch three state etc when serial I O programming is achieved Isolation can be omitted when those signal statuses are output from the MCU peripheral circuit Resistance should be 4 7KQ or over when pull up is achieved to these signals Connect the MCU TXD terminal to the RXD terminal of the MFW1U unit by achieving pull up with resistance of 10KQ In the serial write mode connect CNVss termial of MFW1U and disconnect Vss termial from the MCU by jumper switch In the normal Microcomputer mode disconnect CNVss termial of MFW1U and connect Vss termial from the MCU by jumper switch Connect the reset terminal of the user target board MCU to the RESET terminal of the MFW1U directly when the reset circuit of the user target board is open collector output CR delay circuit or constant current load circuit is less than dozens of uA Execute the same procedure as Note 2 when it is CMOS output The Vss terminal should be connected since it is signal ground Adaptor for the target MFW 20SPe for exclusive use is required in serial programming Execute the same procedure as Note 2 for CE terminal Or only isolation process by achieving pull up without the MFW1U connection is also applicable On board direct fix is also available of the CE terminal for H level when these terminals are not connected Connect the
8. MCU RP terminal to Vss of the user target board Please combine with this example of a connection circuit and confirm a Hardware manual or a Data sheet of each microcomputer Multifunctional Flash Microcomputer S550 MFW1U 37 Operation Manual 6 Updating Firmware If you turn on the Power switch while pressing the START switch the main unit of MFW will achieve waiting state for updating firmware Then update the firmware from the control program of the MFW Control Software For more information on updating firmware please refer to the MFW Control Software Operation Manual Multifunctional Flash Microcomputer S550 MFW1U 38 Operation Manual 7 MFW1U Standalone Operation MFW1U standalone programming is available to device s by downloading conditions and data that have been set in advance by the control program Data saving to the MFW1U unit can is same direction as the standard control program by clicking the Project Exit after device type specification and data load CAUTION Make sure specified Action Type at the main programming screen before pressing the START switch The followings are the instruction for the standalone operations 7 1 Standalone Programming to Parallel Adapter 1 Attach a parallel adapter to the MFW1U unit e Make sure the power of the MFW1U unit is OFF e Not connect a USB cable 2 Turn ON the power of the MFW1U unit e Make sure the PARALLEL SOCKET LED is on All the LEDs
9. Target board or connector at the serial sese urwis adapter side should be prepare by mai Feast water user E Em man Lanat O MFW1U unit ial adapt Target board Serial adapter Bet DO Up to 8 adapters can be Prepared by user i attached Gang prerammin g The AC adapter is not attached for the export product Refer to the 4 Setting Up for detailed and varied connection Multifunctional Flash Microcomputer S550 MFW1U 4 Operation Manual 2 Specifications 2 1 General Specifications Unit of the MFW1U MFW1U DC 9V lower than 1A AC adapter attached for domestic use only Power capacity Use an attached DC cable for oversea use Use environment Ambient temperature 0 C to 40 C Humidity below 80 non condensing Storage Ambient temperature 10 C to 40 C environment Power draw AC 100V lower than 15VA 50 60 Hz AC adapter Outer dimensions 125 W x 100 D x 25 H mm Projection not included Weight Less than 400g only unit CE mark obtained EMI EN55011 Group1 Class A EMS EN61000 6 2 Oversea FCC compliance This device complies with part 15 of the FCC Rules Operation is subject to the following two standards conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Parallel Adapter Outer ee f 162 W x 53 D x 16 H mm Projection
10. are off when a device type and data are not loaded to the MFW1U unit from the control program 3 Place a target device onto the mounter socket of the adapter 4 Press the START switch to execute the selected action at the main programming screen e Result of Action execution is output at the PASS FAIL LEDs of the adapter e Both of the PASS FAIL LEDs are on when a contact error is occurred during execution and operation is interrupted 1 Achieve procedure 3 4 repeatedly for consecutive operation 1 The checksum test of whether the contents of the internal memory is damaged or not is achieved at the timing of data read The PARALLEL SOCKET LED blinks and the beep sound is issued at the same time when damaged Press the START switch to release the LED and beep sound then reload data from PC Reset the device to the mounter socket since only the contact check is achieved and a further action is denied when a contact error is detected Malfunction of a device or mounter socket may be considered when a contact error is repeated Multifunctional Flash Microcomputer S550 MFW1U 39 Operation Manual 7 2 Standalone Programming to Serial Adapter 1 Attach a serial adapter to the MFW1U unit e Not connect a USB cable 2 Turn ON the power of the MFW1U unit e Make sure the SERIAL SOCKET LED is on All the LEDs are off when device type and data are not loaded to the MFW1U unit from the control program 3 Place a target device on
11. checksum test of whether the contents of the internal memory is damaged or not is achieved at the timing of data load The SERIAL TARGET LED blinks and the beep sound is issued at the same time when damaged Press the START switch to release the LED and beep sound then reload data from PC Multifunctional Flash Microcomputer S550 MFW1U 40 Operation Manual 7 4 Initializing Memory Data that is stored at the MFW1U internal memory can be initialized deleted by unit basis for a security purpose The followings are instructions for initializing internal memory 1 Turn on the power of the MFW1U unit e Attachment of a parallel adapter serial adapter or user target board is not necessary Achievement is also available when attached 2 Press the START switch for 5 seconds to start initialization e A series of short beeps P P P is issued when initialization is started and a short beep Peep is issued when finished then all the LEDs are turned off Multifunctional Flash Microcomputer S550 MFW1U 41 Operation Manual 7 5 List of LED Status Action Conditioning LED Status When setting is achieved Any of PARALLEL SERIAL SOCKET or by PC SERIAL TARGET LED is on Power ON When setting by PC is not All the LEDs are off LEDs of MFW1U achieved Both of PASS and FAIL blink parallel adapter mounted When contact error is Both of PASS and FAIL are on serial adapter LEDs of MFW1U malfunction of
12. of the PASS FAIL LEDs are to be on to a troubled adapter when a contact error is detected by either of the above step 1 or 2 NOTE PASS FAIL LEDs of all the adapters are to be on since a troubled device cannot be identified when an error is detected by the step 1 The following error causes are considered for a contact error Release the probable error causes and retry the operation 1 The device is placed improperly such as upside down wrong side or deviation 2 Fail to make connection is occurred since the pin of the IC socket or device is bent 3 Defective of the device Note that the following exceptions are examined 1 Fail to make connection of the Vcc pin Both of the PASS FAIL LEDs are off since the MFW1U judges no device is placed at the IC socket 2 Contact check is not available to the mode set pins and other pins and so the only FAIL LED is on even if the trouble is actually the contact error 3 When the device pin is bent and contacted to the Vcc pin or the H level fixed pin that is connected to the Vcc through resistance the result of a contact check of a troubled device is PASS and other effective device s is are FAIL This kind of device pin bent tends to be occurred at corner pins Therefore inspecting corner pins of a passing device is fully reeommended NOTE The contact point of the IC socket gets dirty and fail to make connection may be occurred during operation Clean the contact point
13. the settings are stored at the MFW1U unit at the time of termination of the PC control software mfwl exe Therefore when Erase Program or Verify is desired please make sure the Action setting is set to Erase Program and Verify before termination Not connect a USB cable when standalone serial programming by the MFW1U Multifunctional Flash Microcomputer S550 MFW1U 17 Operation Manual 5 Connector Pin Specifications for Serial Programming 5 1 Connector MFW1U Unit Model Name HIF2FC 10PA 2 54DS Made by Hirose Electric 5 2 Pin Assignment MFW1U Unit The signal name and the direction are what was seen from the writer side Pin No ee Description Direction ame When to be programmed target is Serial adapter power is supplied to serial adapter from the 1 Vee MFW1U via Vcc pins User prepared target board power is supplied to the MFW1U via Vcc pins from target board prepared by user Note 1 2 BUSY Busy signal input for serial programming Input 3 CLK Clock signal output for serial programming Output 4 TXD Transmission data for serial programming Output 5 CE CE signal output for serial programming Output 6 EPM EPM signal output for serial programming Output 7 GND Signal ground 8 RESET RESET signal output for serial programming Output 9 CNVss CNVss Vpp signal output for serial programming Output 10 RXD Receiving data for serial programming Input Note 1 Attach the AC
14. 550 AD1e or S550 AD2e is necessary Please combine with this example of a connection circuit and confirm a Hardware manual or a Data sheet of each microcomputer Multifunctional Flash Microcomputer S550 MFW1U 35 Operation Manual 14 7641 7643 38C2 38K0 and 38K2 Group Target board prepared by user MCU peripheral circuit RESET Vss Serial cable 5 6 7 8 9 10 Vec CLK CE GND CNVss BUSY TXD EPM RESET RXD MFW1U unit Diagram 14 Note 1 Power supply of the MFW1U for serial programming is provided by a user target board via Vcc pins Connect the power of the board to the Vcc terminal directory Attach the AC adapter to supply power when the current capacity of target board is insufficient since the maximum current consumption of the MFW1U for serial programming is 200mA Usage of Vcc should be 3 8V 5 or 5V 5 Note 2 Isolate TXD RXD SCLK and or BUSY terminals from the MCU peripheral circuit by jumper analog switch three state etc when serial I O programming is achieved Isolation can be omitted when those signal statuses are output from the MCU peripheral circuit Resistance should be 4 7KQ or over when pull up is achieved to these signals Note 3 Execute the same procedure as Note 2 for CE terminal Or only isolation process by achieving pull up without the MFW1U connection is also applicable On board direct fix is also available of the CE terminal for H level when these terminals are not
15. C 24 Group Target board prepared by user MCU peripheral circuit Pull up or Pull down Serial cable Ss 6 7 10 Vcc CLK CE GND CNVss BUSY TXD EPM RESET RXD MFW1U unit Diagram 1 Note 1 Power supply of the MFW1U for serial programming is provided by a user target board via Vcc pins Connect the power of the board to the Vcc terminal directory Attach the AC adapter to supply power when the current capacity of the target board is insufficient since the maximum current consumption of the MFW1U for serial programming is 200mA Usage of Vcc should be 3 3V15 or 5V15 Note 2 Isolate TXD RXD SCLK and or BUSY terminals from the MCU peripheral circuit by jumper analog switch three state etc when serial programming is achieved Isolation can be omitted when those signal statuses are output from the MCU peripheral circuit Resistance should be 4 7KQ or over when pull up is achieved to these signals Note 3 Execute the same procedure as Note 2 for CE and EPM terminals Or only isolation process by achieving pull up down without the MFW1U connection is also applicable On board direct fix is also available of the CE terminal for H level and the EPM terminal Multifunctional Flash Microcomputer S550 MFW1U 20 Operation Manual for L level when these terminals are not connected Note 4 Connect the MCU CNVss terminal to the CNVss terminal of the MFW1U unit by achieving pull up down with resistance of 4 7KQ It a
16. FW1U connection circuit example for R8C 18 R8C 19 Oct 19 2005 R8C 1A and R8C 1B has been added 7 6 Buzzer sound has been added for errors Rev C 7 6 Buzzer sound has been added for No Device Jan 20 2006 Rev C1 5 4 The S550 MFW1U connection circuit example for R8C Tiny series Jul 28 2006 other than R8C 10 R8C 11 R8C 12 and R8C 13 groups have been changed Rev C2 5 4 The S550 MFW1U connection circuit example for M16C 30 has been Sep 08 2006 added Rev C3 5 4 The S550 MFW1U connection circuit example for R32C 100 has been Oct 12 2006 added Rev C4 5 4 The S550 MFW1U connection circuit example for M16C 26A has been Mar 02 2007 added Rev D 2 2 The explanation of Non response to clock asynchronous serial I O Jun 26 2007 has been added to Operation Mode Multifunctional Flash Microcomputer S550 MFW1U 51 Rev E 5 4 The S550 MFW1U connection circuit example for R32C 121 and Dec 19 2008 R32C 100 R32C 121 group removed series has been added Rev F 3 1 DC 9V power jack Apr 27 2009 The error in writing of the specification is corrected 5 4 The S550 MFW1U connection circuit example for M16C 50 has been added The S550 SFW1U connection circuit example for R8C family other than R8C 10 R8C 11 R8C 12 and R8C 13 groups has been changed Rev G 5 4 The S550 MFW1U connection circuit example for R8C LX has been Jul 27 2009 added Rev H_ 5 4 The resistance of the CNVs
17. Multifunctional Flash Microcomputer Programmer 550 MFW1U Operation Manual E Sunny Giken Inc Multifunctional Flash Microcomputer Programmer S550 MFW1U The contents of this manual may be revised without notice We Sunny Giken Inc shall not be responsible for any damages and or losses caused by using this product and or the software attached to this product claimed by users and or any intermediaries Specifications of this product and or the software attached to this product may be modified without notice for improvement The names of systems products and or services used in this manual are either registered trademarks or trademarks of each manufacturer The captions of the TM and R are not mentioned in this manual Multifunctional Flash Microcomputer S550 MFW1U Operation Manual OT XB k Sea rN OS eee Pee EE 3 Lal PYECA tons in lala trade te S 3 12 System CoOntSUTA OO a in da dida caca oa 4 Di SPOCIICATIONS it A cass ie shia PEROT aM 5 2 1 General Specifications ia A E a AE 5 2 2 Function Specifications neistina eeraa a a a ne eee rar aea a a reai a es aleei 6 2 3 Programmable Devices cccccccccccesssssececececeesensscececececeesesssseeececeesessssasecesececcsesesssaeaeeeeecsesensaaeaeeeeeceenes 7 3 Panel Description docs 8 SAANEN E R EENE AAA 8 32 Para lA T E A A T A E N 10 ES Ol AES AT E E E E E N E E ETE E E E 12 41 PC Parallel Progra miming lao 12 49 PC Serial Progr ami MiG ses er ea E a E a A
18. N 13 43 PO t Onboard Prost A a ese is bes a toed 14 4 4 Standalone Parallel Programming ooooccccnnnononononnnononnnananononononnnnonnnnnnnonononnonononnnnnnnnnnnononnnna no nancnccnnono 15 4 5 Standalone Serial Programming ocooococcnononononononnnonononnnnnanononononnonnnnnnnnnnnnnnnnononnnnn nn nn nnnnononnnna nana ncnccnnons 16 4 6 Standalone Onboard Program ming cccccessssscccecesesssssscececececeessessseceecceesenssssaeeeeeesesensnssaeeeeeeeess 17 5 Connector Pin Specifications for Serial Programming ooooocccncnonononononononncnnnnnnonononcnnonnnnnanononononnononnnnn nooo 18 toi A AAA A A A E A Rene aren 18 5 2 Pin Assignment MFW1U Unit osa 18 5 3 Serial Programming Cable ccccccccccccccssessssscececececsesssnecsecesecsesesssseseeeeeesecesssseseeeeeesesenssasaaeeeeeeseeeneas 19 5 4 Connection Circuit Example for the MFW1U oooooncccoccccccnononnononanonononnnnnanonononnnonononnnnononnnnocononnnnonoss 20 GiU pdating Pirin ware ii A e E asa RS a 38 7 MFW1U Standalone Operation ccccccccccccccesssssececececeeeesssneceeeccececeesesssseeeeecseseneseeeeesecsesensaeeeeeeeeeseneeas 39 7 1 Standalone Programming to Parallel Adapter oconcccoocccnnnoncononononanononnnnnanonononononononnanonononocnononnanonoss 39 7 2 Standalone Programming to Serial Adapter ccccccccccccecsesessececeeececeessesssaeeececeesenssssseeeeeeseeensaaeas 40 7 3 Standalone Programming to User Target Board onoooooocconccnnononononnnonononona
19. U 6 Operation Manual 2 3 Programmable Devices The devices from the Renesas Electronics On chip Flash Memory Microcomputer M16C Family are programmable by the MFW1U Some of devices are still under evaluation or not programmable Refer to the file Programmable Device List in an attachment floppy disk Contact Sunny Giken Inc for the latest information Multifunctional Flash Microcomputer S550 MFW1U 7 Operation Manual 3 Panel Description 3 1 MFW1U Unit External views of the MFW1U are shown and its parts such as switches LEDs and connectors are also described e Top view O S550 MFWIU AFRA Multi Flash Writer corssod SERIAL PARALLEL SOCKET TARGET SOCKET POWER START PASS DERR FAL CE SUNNY QIKEN INC Switch LED Function POWER Power Off ON switch Power lamp available Switch START Starts programming Data that had been loaded can be cleared by pressing the START switch more than 5 seconds PARALLEL Turns it ON when programming target is parallel adapter with SOCKET definition by PC SERIAL Turns it ON when programming target is serial adapter with SOCKET definition by PC LED SERIAL Turns it ON when programming target is user target board with TARGET definition by PC PASS Turns it ON when serial programming is successful ID ERR Turns it ON when result of serial programming is ID_ERR FAIL Turns it ON when serial programming is failed Buzzer Sounds when
20. W Control Software PC IBM PC AT Compatible OS Windows98 Me 2000 XP 7 32bit 64bit seesrrrros Up to 8 adapters can be attached Gang prgramming MFW1U unit Up to 8 parallel adapters can be connected and programmed at once gang programming Devices to be gang programmed should be the same type in order to avoid breakage of the devices Beware that the power of the MFW1U is OFF when attaching parallel adapter s Multifunctional Flash Microcomputer S550 MFW1U 12 Operation Manual 4 2 PC Serial Programming Connection instructions for serial programming by PC operation is illustrated below MFW Control Software USB Connection Cable PC IBM PC AT Compatible OS Windows98 Me 2000 XP 7 32bit 64bit DC Cable for Oversea Serial cable Connector at the serial adapter side shuold be prepared by user MFW1U unit Serial adapter Power supply to the serial adapter for serial programming is provided by the MFW1U via Vcc pins Particular power supply is not required A serial adapter can be prepared by obtaining the IC socket type programming board made by Renesas Electronics Some modification to the board is needed since the board mounts Vec3 3V 5V switch circuit Please contact Sunny Giken Inc before operation Multifunctional Flash Microcomputer S550 MFW1U 13 Operation Manual 4 3 PC Onboard Programming Connection instructions for serial pro
21. achieving pull up down without the MFW1U connection is also applicable On board direct fix is also available of the CE terminal for H level or the P16 terminal for H level and the RP terminal for L level when these terminals are not connected Note 4 Connect the MCU CNVss terminal to the CNVss terminal of the MFW1U unit by achieving pull down with resistance of 4 7KQ Note 5 Connect the reset terminal of the user target board MCU to the RESET terminal of the MFWI1U directly when the reset circuit of user target board is open collector output CR delay circuit or constant current load circuit is less than dozens of uA Execute the same procedure as Note 2 when it is CMOS output Note 6 The Vss terminal should be connected since it is signal ground Please combine with this example of a connection circuit and confirm a Hardware manual or a Data sheet of each microcomputer Multifunctional Flash Microcomputer S550 MFW1U 31 Operation Manual 10 M16C 2N Group Note 1 Note 2 Note 3 Note 4 Note 5 Note 6 Target board prepared by user MCU peripheral circuit Note2 CNVss1 CNVss2 AN WI KE sc 4 RESET Vss Reset circuit Serial cable Vcc CLK CE GND CNVss BUSY TXD EPM RESET RXD MFW1U unit Diagram 10 Power supply of the MFW1U for serial programming is provided by a user target board via Vcc pins Connect the power of the board to the Vcc terminal dir
22. adapter to supply power when the current capacity of the target board is insufficient since the maximum current consumption of the MFW1U for serial programming is 200mA Usage of Vcc should be 3 3V 5 or 5V 5 9Pin 1Pin Multifunctional Flash Microcomputer S550 MFW1U 18 Operation Manual 5 3 Serial Programming Cable Attached Serial Programming Cable is designed as a straight cable Cut one side of the connection part and attach a proper connector to your board by reference of the pin assignment shown above if the connection part is not matched In this case a cable length for a serial programming cable should be less than 500mm Be sure to arrange the total length between cable and the target CPU is less than 500mm even if the length of a serial cable is less than 500mm The following figure shows the cable polarity Connector Model HIF3BA 10D 2 54R Manufactured by Hirose Electrics As for serial I O mode of M16C 20 and M16C 21 Group an exclusive programming connector MFW 20SP is necessary C TE lt _ Serial cable MFW1U unit Multifunctional Flash Microcomputer S550 MFW1U 19 Operation Manual 5 4 Connection Circuit Example for the MFW1U Circuit diagram examples for serial programming under customer oriented MCU circuit design are described below 1 M16C 60 double power supplies removed M16C 80 M32C 80 double power supplies removed R32C 100 double power supplies removed Series M16
23. ation Wizard Welcome to the Device Driver py Installation Wizard SS This wizard helps you install the software drivers that some computers devices need in order to work ii The following Dialog will be displayed Press Install F Windows Security Would you like to install this device software Name Sunny Giken Inc Sunny Giken USB device IT Publisher Sunny Giken Inc 7 Always trust software from Sunny Giken Inc Don t Install a You should only install driver software from publishers you trust How can I decide which device software is safe to install Multifunctional Flash Microcomputer S550 MFW1U 46 Operation Manual iii The USB driver package is being installed Please wait for a moment Device Driver Installation Wizard 9 5 Please wait while the drivers install This may take some time to complete iv The following Dialog will be displayed Press Finish Device Driver Installation Wizard Completing the Device Driver 2 Installation Wizard The drivers were successfully installed on this computer Driver Name wv Sunny Giken Inc SUN Multifunctional Flash Microcomputer S550 MFW1U Operation Manual 9 3 Others Windows XP 2000 Me 98 When CFW1 is connected by USB for the first time Windows automatically inspects the new hardware and creates driver information database The procedure for installing USB Driver is described below
24. ch click Next If you are searching on a floppy disk or CD ROM drive insert the floppy disk or CD before clicking Next Optional search locations Il Floppy disk drives I CD ROM drives d 7 Microsoft Windows Update PE iv Specify USBDrv folder in the attached CD ROM for areas to be inspected Found new Hardware wizard x Insert the manufacturer s installation disk into the drive OK selected and then click OK Copy manufacturer s files from G USBDrv z Chrome Multifunctional Flash Microcomputer S550 MFW1U Operation Manual v S550 MFW1U will be viewed Press Next Loc Driver Files Search Results SS The wizard has finished searching for driver files for your hardware device y The wizard found a driver for the following device oy S550 MPW1U Windows found a driver for this device To install the driver Windows found click Next a usbdrv mivwxu inf Cancel vi The driver files will be automatically copied and then installation will be completed Found New Hardware Wizard Completing the Found New Hardware Wizard 550 MFW1U Windows has finished installing the software for this device To close this wizard click Finish Multifunctional Flash Microcomputer S550 MFW1U 50 Operation Manual Revision History Operation Manual Version Contents for cha
25. connected Note 4 Connect the MCU CNVss terminal to the CNVss terminal of the MFW1U unit by achieving pull up down with resistance of 4 7KQ H level fixation by jumper switching is also available Attachment to the MFW1U is not needed for this case Note 5 Connect the reset terminal of the user target board MCU to the RESET terminal of the MFWI1U directly when the reset circuit of the user target board is open collector output CR delay circuit or constant current load circuit is less than dozens of pA Execute the same procedure as Note 2 when it is CMOS output Note 6 The Vss terminal should be connected since it is signal ground Please combine with this example of a connection circuit and confirm a Hardware manual or a Data sheet of each microcomputer Multifunctional Flash Microcomputer S550 MFW1U 36 Operation Manual 15 7542 Group Note 1 Note 2 Note 3 Note 4 Note 5 Note 6 Note 7 Note 8 Note 9 Target board prepared by user MCU peripheral circuit Note2 Diagram 15 Power supply of the MFW1U for serial programming is provided by a user target board via Vcc pins Connect the power of board to the Vcc terminal directory Attach the AC adapter to supply power when the current capacity of the target board is insufficient since the maximum current consumption of the MFW1U for serial programming is 200mA Usage of Vcc should be 3 8V 5 or 5V
26. device may be considered MFW1U damaged malfunction Troubled during N A initialization right after LEDs of MFW1U power is on 7 6 List of Beep Sounds Action Beep Sounds When power is on a long beep sound Peep When start switch is on a short beep sound P When execution is complete Pass a long beep sound Peep When execution is complete Fail a series of beep sounds P P P P P 2 2 2 es gt When no device is connected to a parallel a series of beep sounds P P Peep adapter in parallel mode MFW1U malfunction a series of beep sounds P P P Multifunctional Flash Microcomputer S550 MFW1U 42 Operation Manual 8 Contact Check Stable operation cannot be expected when the connection between a device and IC socket is poor for parallel programming Probability of fail to make of the connection for parallel programming may be higher than serial programming since more pins are used for parallel programming The MFW1U has adopted the contact check function for parallel programming in order to avoid a fail to make connection Contact check is achieved by the following 2 steps described below 1 Short check for the signal pins of a device and the GND pins Checking is achieved to the entire devices at the same time 2 Contact check for the device pins and the IC socket pins Checking is achieved to each device Further operation is interrupted and both
27. ectory Attach the AC adapter to supply power when the current capacity of target board is insufficient since the maximum current consumption of the MFW1U for serial programming is 200mA Usage of Vcc should be 3 3V15 or 5V 5 Isolate TXD RXD SCLK and or BUSY terminals from the MCU peripheral circuit by jumper analog switch three state etc when serial I O programming is achieved Isolation can be omitted when those signal statuses are output from the MCU peripheral circuit Resistance should be 4 7KQ or over when pull up is achieved to these signals Connect the MCU CNVss terminal to the CNVss terminal of the MFW1U unit by achieving pull down with resistance of 4 7KQ Connect the reset terminal of the user target board MCU to the RESET terminal of the MFW1U directly when the reset circuit of the user target board is open collector output CR delay circuit or constant current load circuit is less than dozens of uA Execute the same procedure as Note 2 when it is CMOS output The Vss terminal should be connected since it is signal ground Connect the MCU CNVss1 and CNVss2 terminal to Vss of the user target board Please combine with this example of a connection circuit and confirm a Hardware manual or a Data sheet of each microcomputer Multifunctional Flash Microcomputer S550 MFW1U 32 Operation Manual 11 R8C 10 R8C 11 R8C 12 and R8C 13 Group Target board prepared by user MCU peripheral circu
28. ed Isolation can be omitted when those signal statuses are output from the MCU peripheral circuit Resistance should be 4 7KQ or over when pull up is achieved to these signals Note 3 Execute the same procedure as Note 2 for CE terminal Or only isolation process by achieving pull up without the MFW1U connection is also applicable On board direct fix is also available of the CE terminal for H level when these terminals are not connected Note 4 Connect the MCU CNVss terminal to the CNVss terminal of the MFW1U unit by achieving pull down with resistance of 4 7KQ Note 5 Connect the reset terminal of the user target board MCU to the RESET terminal of the MFW1U directly when the reset circuit of user target board is open collector output CR delay circuit or constant current load circuit is less than dozens of uA Execute the same procedure as Note 2 when it is CMOS output Note 6 The Vss terminal should be connected since it is signal ground Please combine with this example of a connection circuit and confirm a Hardware manual or a Data sheet of each microcomputer Multifunctional Flash Microcomputer S550 MFW1U 29 Operation Manual 8 M16C 26 Group Target board prepared by user MCU peripheral circuit Serial cable 6 10 CE GND CNVss BUSY TXD EPM RESET RXD MFW1U unit Diagram 8 Note 1 Power supply of the MFW1U for serial programming is provided by a user target board
29. ed from to be attached device type Refer to separate Programmable Device List for your order Up to 8 parallel adapters can be connected and programmed at once gang programming But to be gang programmed devices should be the same type to avoid breakage of devices Multifunctional Flash Microcomputer S550 MFW1U 10 Operation Manual Attaching parallel adapters Secure the attachment by placing latch es to avoid fail to make of adapters and safer carriage when more than one adapters are to be attached gang programming to the MFW1U Latch placement for only device mounter socket side is acceptable but securing also at the topside is reliable and recommended The attachment figure is shown below G E E Latches at y y y y 4 the top side PEBRIIIIIIIIILIIJ RIN MW Sx MEWS EW Sx KOLTE FLASH WRITER KOLTE FLAR WRITER KOLTE FLAS WRITER CE SOAT CIKEY INC T Y Latches B El B at mounter socket side y M2 6 Screw Unscrew the M2 6 screws that hold a case cover and screw and attach adapters by referring the above illustration Screwing to the MFW1U unit is not applicable Multifunctional Flash Microcomputer S550 MFW1U 11 Operation Manual 4 Setting Up 4 1 PC Parallel Programming Connection instructions for parallel programming by PC operation is illustrated below USB Connection Cable OE DC Cable for Oversea an Parallel adapter 1 Parallel adapter 2 Parallel adapter 8 O MF
30. esistance of 4 7KQ Note 4 Connect the reset terminal of the user target board MCU to the RESET terminal of the MFW1U directly when the reset circuit of the user target board is open collector output CR delay circuit or constant current load circuit is less than dozens of pA Execute the same procedure as Note 2 when it is CMOS output Note 5 The Vss terminal should be connected since it is signal ground Note 6 Adaptor for the target MFW 20SPe for exclusive use is required in serial programming Please combine with this example of a connection circuit and confirm a Hardware manual or a Data sheet of each microcomputer Multifunctional Flash Microcomputer S550 MFW1U 28 Operation Manual 7 M16C 22 Group Target board prepared by user MCU peripheral circuit Serial cable 6 10 CE GND CNVss BUSY TXD EPM RESET RXD MFW1U unit Diagram 7 Note 1 Power supply of the MFW1U for serial programming is provided by a user target board via Vcc pins Connect the power of the board to the Vcc terminal directory Attach the AC adapter to supply power when the current capacity of the target board is insufficient since the maximum current consumption of the MFW1U for serial programming is 200mA Usage of Vcc should be 3 3V 5 or 5V15 Note 2 Isolate TXD RXD SCLK and or BUSY terminals from the MCU peripheral circuit by jumper analog switch three state etc when serial I O programming is achiev
31. gramming to a user target board by PC operation is illustrated below 9 MFW Control Software USB Connection Cable PC IBM PC AT Compatible 0 OS Windows98 Me 2000 XP 7 32bit 64bit DCCable 4 for Oversea Serial cable Connector at the serial adapter side shuold be prepared MFW1U unit DC power for board Target board Vcc Usage should be Vec 3 3V 5 Prepared by or 5V 5 user Power supply to the MFW1U for serial programming to a user target board is provided by a user target board via Vcc pins Attach the AC adapter to supply power when the current capacity of the target board is insufficient since the maximum current consumption of the MFW1U for serial programming is 200mA Multifunctional Flash Microcomputer S550 MFW1U 14 Operation Manual 4 4 Standalone Parallel Programming Connection instructions for standalone parallel programming by the MFW1U after downloading data from PC is illustrated below DC Cable for Oversea Parallel adapter 1 Parallel adapter 2 Parallel adapter 8 ME ner CLON 150 Up to 8 adapters can be attached Gang prgramming MFW1U unit Standalone parallel programming is available unless data update is occurred since downloaded data from PC to the MFW1U such as lock bit data and several settings retains at the MFW1U even if the power switch is turned OFF Simple operation for everyone without a complicated setting to PC is available by selecting
32. ional Flash Microcomputer S550 MFW1U 33 Operation Manual 12 R8C LX Series Note 1 Note 2 Note 3 Note 4 Note 5 Note 6 Target board prepared by user Reset circuit Serial cable CE GND CNVss BUSY TXD EPM RESET RXD S5350 AD2e Note5 MFW1U unit Diagram 12 Power supply of the MFW1U for serial programming is provided by a user target board via Vcc pins Connect the power of board to the Vcc terminal directory Attach the AC adapter to supply power when the current capacity of the target board is insufficient since the maximum current consumption of the MFW1U for serial programming is 200mA Usage of Vcc should be 3 3V15 or 5V 5 Connect the MCU MODE terminal to the CLK terminal of the MFW1U unit by achieving pull up with resistance of 4 7KQ Connect the reset terminal of the user target board MCU to the RESET terminal of the MFWI1U directly when the reset circuit of the user target board is open collector output CR delay circuit or constant current load circuit is less than dozens of uA Isolate TXD RXD and or BUSY terminals from the MCU peripheral circuit by jumper analog switch three state etc when it is CMOS output The Vss terminal should be connected since it is signal ground An exclusive programming connector S550 AD1e or S550 AD2e is necessary Connect Vref terminal to the VCC Please combine with this example of a connection circuit and confi
33. it Serial cable 6 10 CE GND CNVss BUSY TXD EPM RESET RXD MFW1U unit Diagram 11 Note 1 Power supply of MFW1U is provided by a user target board via Vcc pins Connect the power source of the board to the Vcc terminal directly Usage of Vcc should be 3 3V plus or minus 3 or 5V plus or minus 3 Note 2 Isolate TXD RXD and or BUSY terminals from the MCU peripheral circuit by jumper analog switch three state etc when serial I O programming is achieved Isolation can be omitted when those signal statuses are output from the MCU peripheral circuit Resistance should be 4 7KQ or over when pull up is achieved to these signals Note 3 Connect the MCU MODE terminal to the BUSY terminal of the MFW1U unit by achieving pull up with resistance of 4 7KQ Note 4 Connect the MCU CNVss terminal to the CLK terminal of the MFW1U unit by achieving pull down with resistance of 4 7KQ Note 5 Connect the reset terminal of the user target board MCU to the RESET terminal of the MFW1U directly when the reset circuit of user target board is open collector output CR delay circuit or constant current load circuit is less than dozens of uA Execute the same procedure as Note 2 when it is CMOS output Note 6 The Vss terminal should be connected since it is signal ground Please combine with this example of a connection circuit and confirm a Hardware manual or a Data sheet of each microcomputer Multifunct
34. lf 2 Use Environment e Unusable environment Dusty place Place in the presence of corrosive gasses Place exposed to direct sunlight Place surrounded by equipment which originates noises Place with severe mechanical shock and or constant mechanical vibration e Ambient temperature 0 C to 40 C Humidity below 80 non condensing e Prevention of electrostatic buildup for operation of this product and devices is recommended 3 Storage e Place this product into the packing box which had been delivered when your purchase and store at shaded place with the ambient temperature of 10 C to 40 C and below 80 of humidity non condensing for long term storage 4 Transportation e In case the product is needed to be relocated use the packing box which had been delivered when your purchase 5 Cleaning e Wipe the product with soft and clean fabric Never use any sort of organic solvent such as benzine that may cause this product deteriorated Multifunctional Flash Microcomputer S550 MFW1U 3 Operation Manual 1 2 System Configuration The entire system configuration of the Multifunctional Flash Microcomputer Programmer hereinafter called MFW1U is illustrated below MFW Control Software USB Connecting Cable PC IBM PC AT Compatible OS Windows98 Me 2000 XP Windows7 32bit 64bit DC Cable for Oversea i Parallel adapter Cable for serial programming hereinafter called the serialcable
35. lso can be defined to H level by switching the jumper as well as CE and EPM terminals when serial programming No connection to the MFW1U is not required for this operation Note 5 Connect the reset terminal of the user target board MCU to the RESET terminal of the MFWI1U directly when the reset circuit of the user target board is open collector output CR delay circuit or constant current load circuit is less than dozens of pA Execute the same procedure as Note 2 when it is CMOS output Note 6 The Vss terminal should be connected since it is signal ground Please combine with this example of a connection circuit and confirm a Hardware manual or a Data sheet of each microcomputer Multifunctional Flash Microcomputer S550 MFW1U 21 Operation Manual 2 M16C 60 double power supplies M32C 80 double power supplies R32C 100 double power supplies Series M16C 30P Group Target board prepared by user MCU peripheral circuit Pull up or Pull down RESET Vss Serial cable 3 5s 6 7 1d 1 4 Vec CLK C ND CNVss BUSY TXD RESET RXD E G EPM MFW1U unit Diagram 2 Note 1 Be sure to set it so that Vccl is greater than or equal to Vcc2 Note 2 Pull up with Vcc2 Refer to the Note5 regarding the CE terminal when Vccl is equal to Vec2 Note 3 Power supply of the MFW1U for serial programming is provided by a user target board via Vcc pins Connect the power of the board to the Vcc terminal direc
36. nge SA ate The First Edition Apr 18 2003 Rev Al 5 4 The S550 MFW1U connection circuit example for M16C 26 and 7542 May 23 2003 has been added Rev A2 5 4 The S550 MFW1U connection circuit example for M16C 62P and Jul 18 2003 R8C Tiny has been added Rev A3 5 4 The S550 MFW1U connection circuit example for M32C 84 M32C 85 Nov 25 2003 M32C 86 M16C 28 and 7643 has been added Rev A4 5 4 The S550 MFW1U connection circuit example for M16C 29 has been Jan 23 2004 added Rev A5 4 4 Notes of standalone parallel programming are added May 20 2004 4 5 Notes of standalone serial programming are added 4 6 Notes of standalone onboard programming are added 5 4 The S550 MFW1U connection circuit example for R8C 12 and R8C 13 has been added 5 4 The S550 MFW1U connection circuit example for M16C 26 M16C 28 and M16C 29 has been changed 7 1 Notes of standalone parallel programming are added 7 2 Notes of standalone serial programming are added 7 3 Notes of standalone onboard programming are added Rev A6 5 4 The S550 MFW1U connection circuit example for 7542 has been Jun 07 2004 changed Rev B 5 4 The S550 MFW1U connection circuit example for R8C 14 R8C 15 Sep 03 2004 R8C 16 and R8C 17 has been added Rev B1 5 4 The S550 MFW1U connection circuit example for 7542 has been Dec 10 2004 changed Rev B2 5 4 The S550 MFW1U connection circuit example for M16C 28 and Apr 20 2005 M16C 29 has been changed Rev B3 5 4 The S550 M
37. nononononocononnnnononononnononnnnonoss 40 4 Initializing Memory A A vba tee E O E BE 41 Ta istot LED STATUS aih nea aana a a a Ucables iio ld lbn 42 4 6 Listof Beep Sounds 2d a 42 8 Contact CHECK tutti tE a EE e AA a 43 9 Tunstall US BaD Fy OF it A a a a a Aaa a Sete tec a as 44 lo Pa RAUEN Ye LOANS 1 o PA oT DIEE E EAE EE A aoe AA AAAA 44 OD Windows iaa 46 9 3 Others Windows XP 2000 Me 98 c ccceccccecsccsccescesccsccesecsccsscsscesscssecsssesceseceseesscsecsueesstssessecseeeseeas 48 Multifunctional Flash Microcomputer S550 MFW1U 2 Operation Manual 1 Outline 1 1 Precautions Thank you for purchasing our product S550 MFW1U the Multifunctional Flash Microcomputer Programmer Please read this operation manual carefully to understand the function of this product for effective and stable operation Please beware that Sunny Giken Inc shall have no liability for any damage and or troubles caused by misuse or careless handling 1 General Caution Please follow the precautions mentioned below to avoid hazards such as fire burns electric shock and or injures e Make sure that the power switch of this product is turned OFF and your hands are clean and dry when an AC adapter is plugged in e Use this product under proper environment e Never place this product upside down or lateral side facing to table e Handle this product with care to avoid fall and or physical shock e Never take this product apart and or modify by yourse
38. not included dimensions Weight Less than 400g Beware that the shape of the IC socket of the parallel adapter is varied from to be attached device type The height 16mm mentioned at the above Outer dimensions is only size of the case The polarity of this DC cable is illustrated below 500mm RED DC 9V Wire color CL oooo gt BLAGIECND Multifunctional Flash Microcomputer S550 MFW1U 5 Operation Manual 2 2 Function Specifications Programmable MCU Renesas Electronics On chip Flash Memory Microcomputer Operation Mode Parallel I O mode gang programmable up to 8 devices can be programmed at once lt Auto device set number detection and contact check function are available gt Standard serial I O mode clock synchronous serial I O and single wire clock asynchronous serial I O applicable to R8C Family Clock asynchronous serial I O mode not supported Program Mode PC parallel programming PC serial programming PC onboard programming Standalone parallel programming Standalone serial programming Standalone onboard programming Program data Size Max 1Mbyte PC control All the operation can be achieved from your PC with easy to operate GUI Software graphic user interface Applicable to the Win98 Me 2000 XP isl 7 32bit 64bit Interface USB 1 1 supported Full speed Mode Multifunctional Flash Microcomputer S550 MFW1
39. operation is completed or error is issued Multifunctional Flash Microcomputer S550 MFW1U 8 Operation Manual e Back view Connector Function DC9VIN DC 9V power jack 45 15 holes Center 41 65mm compliance EIAJ RC 5320 class3 USB USB communication connector connected to PC e Left hand side view SERIAL Connector Function SERIAL Serial programming connector for target board or serial adapter e Right hand side view Connector Function PARALLEL Parallel programming connector for parallel adapter Multifunctional Flash Microcomputer S550 MFW1U Operation Manual 3 2 Parallel Adapter At the next external views of the parallel adapter are shown and its parts such as LEDs and connectors are also described MFW Sx MULTI FLASH RITER Conmectorl Connector2 41H HHH 4014 0 44 44 4 HHH 4 4 044 4H HHH 140 ee ey ir T Ja i aa gt O O PASS FAIL LED Connector Function Socket Mounter socket for device programming PASS LED Turns it ON when parallel programming is successful FAIL LED Turns it ON when parallel programming is failed Connector 1 Parallel programming connector from the MFW1U Connector 2 Gang parallel programming connector when more than one parallel adapters attached The shape of the IC socket of the parallel adapter is vari
40. r target board but do not connect to the CNVss terminal of the MFW1U unit Connect the MCU BUSY terminal to the BUSY terminal of the MFW1U unit by achieving pull up down with resistance of 10KQ Connect the reset terminal of the user target board MCU to the RESET terminal of the MFWI1U directly when the reset circuit of the user target board is open collector output CR delay circuit or constant current load circuit is less than dozens of pA Execute same procedure as Note 2 when it is CMOS output The Vss terminal should be connected since it is signal ground Please combine with this example of a connection circuit and confirm a Hardware manual or a Data sheet of each microcomputer Multifunctional Flash Microcomputer S550 MFW1U 24 Operation Manual 4 M16C 50 Series Target board prepared by user MCU peripheral circuit Serial cable 3 4 S 6 8 9 10 Vcc CLK CE GND CNVss BUSY TXD EPM RESET RXD MFW1U unit Diagram 4 Note 1 Power supply of the MFW1U for serial programming is provided by a user target board via Vcc pins Connect the power of the board to the Vcc terminal directory Attach the AC adapter to supply power when the current capacity of the target board is insufficient since the maximum current consumption of the MFW1U for serial programming is 200mA Usage of Vcc should be 3 3V 5 or 5V15 Note 2 Isolate TXD RXD SCLK and or BUSY terminals from the MCU peripheral circui
41. rm a Hardware manual or a Data sheet of each microcomputer Multifunctional Flash Microcomputer S550 MFW1U 34 Operation Manual 13 RSC Family other than R8C 10 R8C 11 R8C 12 R8C 13 Group and R8C LX Series Target board prepared by user Reset circuit RESET Vss Serial cable Vee CLK CE GND CNVss BUSY TXD EPM RESET RXD S550 AD2e Note5 MFW1U unit Diagram 13 Note 1 Power supply of the MFW1U for serial programming is provided by a user target board via Vcc pins Connect the power of board to the Vcc terminal directory Attach the AC adapter to supply power when the current capacity of the target board is insufficient since the maximum current consumption of the MFW1U for serial programming is 200mA Usage of Vcc should be 3 3V15 or 5V 5 Note 2 Connect the MCU MODE terminal to the CLK terminal of the MFW1U unit by achieving pull up with resistance of 4 7KQ Note 3 Connect the reset terminal of the user target board MCU to the RESET terminal of the MFW1U directly when the reset circuit of the user target board is open collector output CR delay circuit or constant current load circuit is less than dozens of uA Isolate TXD RXD and or BUSY terminals from the MCU peripheral circuit by jumper analog switch three state etc when it is CMOS output Note 4 The Vss terminal should be connected since it is signal ground Note 5 An exclusive programming connector S
42. s terminal in the S550 MFW1U connection Jul 22 2010 circuit example is corrected from 10KQ to 4 7KQ or more 1 2 4 5 6 7 8 9 10 11 14 5 4 The resistance of the MODE terminal in the S550 MFW1U connection circuit example is corrected from 10KQ to 4 7KQ or more 11 5 4 The resistance of the MODE terminal in the S550 MFW1U connection circuit example is corrected from 10KQ to 4 7KQ or more 12 13 Rev I 9 Installing USB Driver Mar 17 2011 9 1 Windows 7 32bit has been added Rev J 9 Installing USB Driver Jul 26 2011 9 2 Windows 7 64bit has been added Multifunctional Flash Microcomputer S550 MFW1U 52 Operation Manual Overseas Specifications e Obtaining the CE Mark EMI EN55011 Group1 Class A EMS EN61000 6 2 e FCC Compliance This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Multifunctional Flash Microcomputer Programmer S550 MFW1U Operation Manual Date of Issue Editor Published by E mail Apr 2003 The First Edition Jul 2011 Rev J SUNNY GIKEN INC SUNNY GIKEN INC 3 1 9 Nishidai Itami Hyogo JAPAN 664 0858 info sunnygiken co jp 2003 2011 Sunny Giken Inc All rights reserved Multifunctional Flash Microcomputer S550 MFW1U Opera
43. t or constant current load circuit is less than dozens of nA Execute the same procedure as Note 2 when it is CMOS output Multifunctional Flash Microcomputer S550 MFW1U 26 Operation Manual Note 7 The Vss terminal should be connected since it is signal ground Please combine with this example of a connection circuit and confirm a Hardware manual or a Data sheet of each microcomputer Multifunctional Flash Microcomputer S550 MFW1U 27 Operation Manual 6 M16C 20 M16C 21 Group Target board prepared by user MCU peripheral circuit Serial cable MFW1U unit Diagram 6 Note 1 Power supply of the MFW1U for serial programming is provided by a user target board via Vcc pins Connect the power of board to the Vcc terminal directory Attach the AC adapter to supply power when the current capacity of the target board is insufficient since the maximum current consumption of the MFW1U for serial programming is 200mA Usage of Vcc should be 3 3V15 or 5V 5 Note 2 Isolate TXD RXD SCLK and or BUSY terminals from the MCU peripheral circuit by jumper analog switch three state etc when serial I O programming is achieved Isolation can be omitted when those signal statuses are output from the MCU peripheral circuit Resistance should be 4 7KQ or over when pull up is achieved to these signals Note 3 Connect the MCU CNVss terminal to the CNVss terminal of the MFW1U unit by achieving pull down with r
44. t by jumper analog switch three state etc when serial I O programming is achieved Isolation can be omitted when those signal statuses are output from the MCU peripheral circuit Resistance should be 4 7KQ or over when pull up is achieved to these signals Note 3 Connect the MCU CNVss terminal to the CNVss terminal of the MFW1U unit by achieving pull down with resistance of 4 7KQ Note 4 Connect the reset terminal of the user target board MCU to the RESET terminal of the MFW1U directly when the reset circuit of user target board is open collector output CR delay circuit or constant current load circuit is less than dozens of uA Execute the same procedure as Note 2 when it is CMOS output Note 5 The Vss terminal should be connected since it is signal ground Please combine with this example of a connection circuit and confirm a Hardware manual or a Data sheet of each microcomputer Multifunctional Flash Microcomputer S550 MFW1U 25 Operation Manual 5 M16C 1N Group Target board prepared by user MCU peripheral circuit Serial cable 5 6 7 8 9 10 Vec CLK CE GND CNVss BUSY TXD EPM RESET RXD MFW1U unit Diagram 5 Note 1 Power supply of the MFW1U for serial programming is provided by a user target board via Vcc pins Connect the power of the board to the Vcc terminal directory Attach the AC adapter to supply power when the current capacity of target board is insufficient since the
45. tion Manual 53
46. to the mounter socket of the adapter 4 Press the START switch to execute the selected action at the main programming screen 1 e Result of Action execution is output at the PASS FAIL LEDs of the adapter Achieve procedure 3 4 repeatedly for consecutive operation 1 The checksum test of whether the contents of the internal memory is damaged or not is achieved at the timing of data load The SERIAL SOCKET LED blinks and the beep sound is issued at the same time when damaged Press the START switch to release the LED and beep sound then reload data from PC 7 3 Standalone Programming to User Target Board 1 Attach a user target board to the MFW1U unit e Not connect a USB cable 2 Turn ON the power of the user target board e Make sure the power of the MFW1U is off 2 e Make sure the SERIAL TARGET LED is on All the LEDs are off when device type and data are not loaded to the MFW1U unit from the control program 3 Press the START switch to execute the selected action at the main programming screen 3 4 Result of Action execution is output at the PASS FAIL LEDs of the adapter 5 Detach the user target board from the MFW1U unit after turning off the power of user target board Achieve procedure 1 5 repeatedly for consecutive operation 2 Use the AC adapter attached to the MFW1U when the user target board cannot provide enough power to the MFW1U Leave the power switch of the MFW1U is on in this case 3 The
47. tory Attach the AC adapter to supply power when the current capacity of the target board is insufficient since the maximum current consumption of the MFW1U for serial programming is 200mA Usage of Vcc should be 3 3V15 or 5V15 Note 4 Isolate TXD RXD SCLK and or BUSY terminals from the MCU peripheral circuit by jumper analog switch three state etc when serial programming is achieved Isolation can be omitted when those signal statuses are output from the MCU peripheral circuit Resistance should be 4 7KQ or over when pull up is achieved to these signals Note 5 Execute the same procedure as Note 2 for CE and EPM terminals Or only isolation process by achieving pull up down without the MFW1U connection is also applicable On board direct fix is also available of the CE terminal for H level and the EPM terminal for L level when these terminals are not connected Note 6 Connect the MCU CNVss terminal to the CNVss terminal of the MFW1U unit by Multifunctional Flash Microcomputer S550 MFW1U 22 Operation Manual achieving pull up down with resistance of 4 7KQ It also can be defined to H level by switching the jumper as well as CE and EPM terminals when serial programming No connection to the MFW1U is not required for this operation Note 7 Connect the reset terminal of the user target board MCU to the RESET terminal of the MFWI1U directly when the reset circuit of the user target board is open collector output
48. via Vcc pins Connect the power of the board to the Vcc terminal directory Attach the AC adapter to supply power when the current capacity of the target board is insufficient since the maximum current consumption of the MFW1U for serial programming is 200mA Usage of Vcc should be 3 3V 5 or 5V15 Note 2 Isolate TXD RXD SCLK and or BUSY terminals from the MCU peripheral circuit by jumper analog switch three state etc when serial I O programming is achieved Isolation can be omitted when those signal statuses are output from the MCU peripheral circuit Resistance should be 4 7KQ or over when pull up is achieved to these signals Note 3 Execute the same procedure as Note 2 for CE and RP terminal Connect CE terminal to CE of MFW1U or connect RP terminal to EPM of MFW1U Or only isolation process by achieving pull up down without the MFW1U connection is also applicable On board direct fix is also available of the CE terminal for H level or the RP terminal for L level when these terminals are not connected Note 4 Connect the MCU CNVss terminal to the CNVss terminal of the MFW1U unit by achieving pull down with resistance of 4 7KQ Note 5 Connect the reset terminal of the user target board MCU to the RESET terminal of the MFW1U directly when the reset circuit of user target board is open collector output CR delay circuit or constant current load circuit is less than dozens of pA Execute the same procedure as
49. with a brush sometimes Multifunctional Flash Microcomputer S550 MFW1U 43 Operation Manual 9 Installing USB Driver 9 1 Windows 7 32bit i Execute dpinst exe of the Driver32 folder Device Driver Installation Wizard Dialog will be displayed Press Next Device Driver Installation Wizard y Welcome to the Device Driver Y Installation Wizard This wizard helps you install the software drivers that some computers devices need in order to work To continue click Next lt Back Cancel ii The USB driver package is being installed Please wait for a moment Device Driver Installation Wizard The drivers are now installing Na 1 5 Please wait while the drivers install This may take some time to complete Next gt lt Back Multifunctional Flash Microcomputer S550 MFW1U 44 Operation Manual iii The following Dialog will be displayed Press Finish Device Driver Installation Wizard Completing the Device Driver lt gt Installation Wizard The drivers were successfully installed on this computer MY Sunny Giken Inc SUN Device Updated Finish Cancel Multifunctional Flash Microcomputer S550 MFW1U Operation Manual 45 9 2 Windows 7 64bit i Execute dpinst exe of the Driver64 folder Device Driver Installation Wizard Dialog will be displayed Press Next Device Driver Install
Download Pdf Manuals
Related Search