USER MANUAL - AV
Contents
1. 0 12 7 8 1 12 7 9 2 12 7 10 3 12 8 9 4 12 8 10 5 12 9 10 6 12 7 9 7 Service use only For example if the rotary switch is in position 4 the 3 buttons on the RC 3TB will duplicate the functions of buttons 12 8 and 10 on the SL 14RC That is in this example pressing button 1 on the RC 3TB has the same effect as pressing button 12 on the SL 14RC pressing button 2 on the RC 3TB has the same effect as pressing button 8 on the SL 14RC and pressing button 3 on the RC 3TB has the same effect as pressing button 10 on the SL 14RC Note The rotary switch configuration is only read at switch on Therefore when changing the rotary switch position you must switch off the SL 14RC and then switch it on again for the new settings to take effect For connecting the RC 3TB see Section 7 3 Installing the SL 14RC in a Rack 6 Installing the SL 14RC in a Rack This section provides instruction on rack mounting the SL 14RC Before Installing in a Rack How to Rack Mount Before installing in a rack be sure that the To rack mount a machine environment is within the recommended range 1 Attach both ear brackets to the 5 to 45 C 41 to 13 machine To do so remove the Operating humidity ran 40 to 90 RHL non condensing screws from each side of the Storage temperature range 20 to 70 C 4 to 158 F machine 3 on each side and Storage humidity range to 95 RHL non condensing replace those screws throu2. Front Panel Button Labels Note The button caps are a press fit on the buttons and must be removed carefully or the buttons may be damaged Remove the button caps only with the supplied button cap suction removal tool To replace the front panel button labels 1 2 3 4 Using the supplied button cap suction removal tool gently pull the button cap away from the button Do not use excessive force Remove the required labels from the supplied button label sheet Remove the old label from inside the button and insert the new label into the button cap Taking care that the button is oriented correctly gently press the button cap on to the button of the SL 14RC 10 Technical Specifications The SL 14RC technical specifications are shown in Table 5 Table 5 SL 14RC Master Controller Technical Specifications INPUTS 1 K NET and 6 RS 232 on terminal block connectors 1 Ethernet on RJ 45 connector 1 infrared OUTPUTS 2 relays 36V AC or DC 2A 60VAC maximum on non inductive load 1 GPVO 2 IR ports on terminal block connectors DEFAULT IP IP number 192 168 1 39 Mask 255 255 0 0 Gateway 0 0 0 0 SETTINGS POWER SOURCE 100 240VAC 22VA DIMENSIONS 48 26cm x 11 5cm x 1U 19 x 4 5 x 1U W D H WEIGHT 0 6kg 1 4lbs approx ACCESSORIES Power cord rack ears and K Config Configuration Software OPTIONS RC 3TB Remote Control Panel IR emitter cables The RC 3TB technical sp
3. makes changes or modifications to the unit without the expressed approval of the manufacturer will void user authority to operate the equipment Use the supplied DC power supply to feed power to the machine amp Please use recommended interconnection cables to connect the machine to other components FCC and CE approved using STP cable for twisted pair products 14 Li For the latest information on our products and a list of Kramer distributors visit our Web site www kramerelectronics com where updates to this user manual may be found We welcome your questions comments and feedback Safety Warning Disconnect the unit from the power supply before opening servicing Caution Kramer Electronics Ltd Web site www kramerelectronics com E mail info kramerel com P N 2900 000598 REV 3
4. 0 KRAMER SIMPLE CREATIVE TECHNOLOGY Connecting the SL 14RC Master Controller 7 3 1 7 3 2 K NET GBA 12V Figure 6 K NET to RC 3TB Connection Terminating RC 3TB Remote Control Panels If only one RC 3TB is connected it must be terminated and the termination on the SL 14RC is turned off see Section 7 3 1 When viewed from above and the rotary switch is to the left of the termination switch slide the termination switch to the left as shown in Figure 6 Only the last RC 3TB in the chain should be terminated Daisy chaining Multiple RC 3TB Remote Control Panels The wiring of two RC 3TB panels to the K NET port on the SL 14RC is shown in Figure 6 Connection of more than two RC 3TB panels follows the same principle K NET G B A 12V Figure 7 Daisy chaining Multiple RC 3TB Panels Note the position of the termination switch on the first RC 3TB open to the right and that of the second RC 3TB closed to the left Connections to an SL 14RC or to another RC 3TB can be made to either connector block as the connector blocks are functionally identical 11 Operating the SL 14RC Master Controller 8 Operating the SL 14RC Master Controller You can operate your SL 14RC using e Front panel buttons These are configured using the K Config software For instructions on using the software see the K Config Software Guide available from our Web site e RC 3TB Remote Control Panels optional e A PC running Sit
5. HNOLOGY Overview 3 Overview The SL 14RC is a highly versatile master room controller that acts as an all in one extended remote control panel for control of A V equipment especially projectors and associated equipment in any room such as classrooms boardrooms or auditoriums It streamlines operations and simplifies control by integrating audio video and computer video sources into a centralized system Optional 3 button remote control panels are available which enable you to remotely duplicate the functionality of front panel buttons The SL 14RC Master Controller features 12 configurable front panel buttons configured using the K Config Configuration software 1 configurable rotary up down controller with direction indicator LEDs configured using the K Config Configuration software 1 general purpose I O port that can be configured as an analog input digital input or digital output for interfacing with a variety of devices such as sensors switches LEDs and relays 6 bi directional RS 232 ports that can control AV equipment such as projectors LCD and PDP displays power amplifiers switchers and scalers 2 relay contacts that can control other room items related to the AV system such as raising and lowering drapes screen or projector IR control on 2 outputs terminal blocks IR Learning that learns commands from any IR remote Compatibility with Kramer Site CTRL software for network remote control and manag
6. Kramer Electronics Ltd USER MANUAL Models SL 14RC Master Controller RC 3TB Remote Control Panel Optional Contents Contents 1 Introduction 2 Getting Started 2 1 Quick Start 3 Overview 4 Defining the SL 14RC Master Controller 5 Defining the RC 3TB Remote Control Panel Optional 6 Installing the SL 14RC in a Rack 7 Connecting the SL 14RC Master Controller 7 1 Connecting the RS 232 Interface 7 2 Connecting the Ethernet Port 7 3 Connecting RC 3TB Remote Control Panels Optional 7 3 1 Terminating RC 3TB Remote Control Panels 7 3 2 Daisy chaining Multiple RC 3TB Remote Control Panels 8 Operating the SL 14RC Master Controller 9 Front Panel Button Caps and Labels 9 1 Installing the Front Panel Button Caps and Labels 9 2 Replacing the Front Panel Button Labels 10 Technical Specifications Figures Figure 1 SL 14RC Master Controller Front Panel Figure 2 SL 14RC Master Controller Rear Panel Figure 3 RC 3TB Remote Control Panel Components Figure 4 Connecting the SL 14RC Master Controller Figure 5 RS 232 Connection Figure 6 K NET to RC 3TB Connection Figure 7 Daisy chaining Multiple RC 3TB Panels Figure 8 Sample Button Label Sheet Tables Table 1 SL 14RC Master Controller Front Panel Features Table 2 SL 14RC Master Controller Rear Panel Features Table 3 RC 3TB Remote Control Panel Functions Table 4 RC 3TB Rotary Switch Button Assignment Table 5 SL 14RC Master Controller Technical Specifi
7. cations Table 6 RC 3TB Remote Control Panel Technical Specifications DRA FW YN 10 10 11 11 12 12 12 13 13 VUNDAR jaj Introduction 1 Introduction Welcome to Kramer Electronics Since 1981 Kramer Electronics has been providing a world of unique creative and affordable solutions to the vast range of problems that confront the video audio presentation and broadcasting professional on a daily basis In recent years we have redesigned and upgraded most of our line making the best even better Our 1 000 plus different models now appear in 11 groups that are clearly defined by function Thank you for purchasing the Kramer SL 14RC Master Controller which is ideal for controlling multimedia rooms such as classrooms auditoriums conference rooms and so on while enabling remote control and management of the AV equipment Each package includes the following items e The SL 14RC Master Controller e Kramer K Config software e Power cord rack ears and this user manual Optional component e RC 3TB Remote Control Panel 2 Getting Started We recommend that you e Unpack the equipment carefully and save the original box and packaging materials for possible future shipment e Review the contents of this user manual e Use Kramer high performance high resolution cables 1 GROUP 1 Distribution Amplifiers GROUP 2 Switchers and Matrix Switchers GROUP 3 Control Systems GROUP 4 Format Standar
8. ds Converters GROUP 5 Range Extenders and Repeaters GROUP 6 Specialty AV Products GROUP 7 Scan Converters and Scalers GROUP 8 Cables and Connectors GROUP 9 Room Connectivity GROUP 10 Accessories and Rack Adapters GROUP 11 Sierra Products 2 The latest version of the K Config software is available from http www kramerelectronics com 3 Download up to date Kramer user manuals from http www kramerelectronics com 4 The complete list of Kramer cables is on http www kramerelectronics com 1 Getting Started 2 1 Quick Start The following quick start chart summarizes the basic setup and operation steps Step 1 Mount the machine Mount the machine in a rack or stick the 4 rubber feet to the underside Step 2 Connect the inputs and outputs see section 6 To RC 3TB Connect the IR outputs Connect the I O port Connect the relays Connect the Ethemet Connect the RS 232 Connect the K NET Optional Connect the RC 3TB Remote Control Panel s DOONUN Moton Detector Lighting Power Amplifier Laptop ruming System with Speakers ite CTRL Step 3 Optional Configure the RC 3TB Remote Control Panel s Set the termination on the last RC 3TB Step 4 Connect the power Step 5 Configure the unit using the K Config software see the K Config Configuration Guide Step 6 Operate the unit Operate via the front panel pushbuttons IR remote control K NET or ETHERNET 2 KRAMER SIMPLE CREATIVE TEC
9. e CTRL control software To operate your device using Site CTRL see the Site CTRL User Guide available at the Kramer Web site 9 Front Panel Button Caps and Labels The SL 14RC is supplied with a button label sheet and 12 clear button caps to house the labels Figure 8 illustrates a sample button label sheet Ly Pci ovog MATRIX 2 ACCEPT 4 S VIDEO 2 TUNER LOCK KRAM JELE pea CAM 2 ACCEPT 2 wer RGOBHV 1 TUNER 2 AUX 1 wee ROBHV 2 RADIO 1 OFF ER 7 LAPTOP 2 cal 1 TURN TABLE TAPE 1 AUX yuvi VIDEO 4 SWITCH 1 yuve vo DOWN 3 ovo 1 MATRIX 1 SOURCE 2 S VIDEO 4 co PLAYER MUTE MENU SYNC SCREEN DOWN ZOOM ouT Laptop RECOVER EX gt Pl Figure 8 Sample Button Label Sheet 9 1 Installing the Front Panel Button Caps and Labels To install the button caps and labels 1 Remove the required labels from the supplied button label sheet 1 www kramerelectronics com 2 Available in the near future FREEZE CASSETTE maven laa AUTO BLANK NU NU a v4 4 E ii 12 KRAMER SIMPLE CREATIVE TECHNOLOGY Technical Specifications 4 Remove the supplied button caps from the bag and insert the labels into the button caps Taking care that the button is oriented correctly gently press the button cap on to the required button of the SL 14RC Repeat for all the button caps 9 2 Replacing the
10. e K NET port to the input of the first RC 3TB see Section 7 3 7 Connect the output of the first RC 3TB to the input of the second RC 3TB see Section 7 3 1 D 7 1 Connecting the RS 232 Interface To connect an AV device to the SL 14RC using the RS 232 port connect the RS 232 9 pin D sub port on your AV device to the RS 232 terminal block on the rear panel of the SL 14RC as shown in Figure 5 RS 232 Device SL 14RC Ground gam GRT GRIT GRT GRXTk G RTX Figure 5 RS 232 Connection 7 2 Connecting the Ethernet Port The Ethernet connection of the SL 14RC lets you perform all control functions of the SL 14RC over the Internet using a PC running the Kramer Site CTRL control program To connect the SL 14RC to a network 1 Connect the Ethernet port of the SL 14RC to the Ethernet port on a network hub or network router via a straight cable with RJ 45 connectors 2 At the other end connect the Internet to a PC running Site CTRL 3 After connecting the Ethernet port you have to install and configure it For detailed instructions on how to install and configure your Ethernet port see the K Config Software Guide available from our Web site 7 3 Connecting RC 3TB Remote Control Panels Optional One or more RC 3TB panels may be connected to the K NET port on the SL 14RC in a daisy chain configuration The wiring from a K NET port to a single RC 3TB is shown in Figure 6 1 At http www kramerelectronics com 1
11. ecifications are shown in Table 6 Table 6 RC 3TB Remote Control Panel Technical Specifications DIMENSIONS 8 9cm x 2 1cm x 2 3cm 3 5 x 0 8 x 0 9 W D H WEIGHT 0 1kg 0 22Ibs approx 1 Specifications are subject to change without notice 13 LIMITED WARRANTY Kramer Electronics hereafter Kramer warrants this product free from defects in material and workmanship under the following terms HOW LONGIS THE WARRANTY Labor and parts are warranted for seven years from the date of the first customer purchase WHOIS PROTECTED Only the first purchase customer may enforce this warranty WHAT IS COVERED AND WHAT IS NOT COVERED Except as below this warranty covers all defects in material or workmanship in this product The following are not covered by the warranty 1 Any product which is not distributed by Kramer or which is not purchased from an authorized Kramer dealer If you are uncertain as to whether a dealer is authorized please contact Kramer at one of the agents listed in the Web site www kramerelectronics com 2 Any product on which the serial number has been defaced modified or removed or on which the WARRANTY VOID IF TAMPERED sticker has been torn reattached removed or otherwise interfered with 3 Damage deterioration or malfunction resulting from i Accident misuse abuse neglect fire water lightning or other acts of nature ii Product modification or failure to follow in
12. ed presets 5 Defining the RC 3TB Remote Control Panel Optional 5 Defining the RC 3TB Remote Control Panel Optional Figure 3 and Table 3 define the SL 14RC Figure 3 RC 3TB Remote Control Panel Components Table 3 RC 3TB Remote Control Panel Functions Feature Function 1 Mounting Holes 2 holes for mounting the RC 3TB to the PTBUS 3 or TBUS 6W 2 Button 1 Function is always assigned to button 12 on SL 14RC 3 Buttons 2 and 3 Function is assigned by the rotary switch position see Table 4 4 K NET Connector Connects to either SL 14RC or additional RC 3TB 5 8 Position Rotary Switch For assigning which buttons on the SL 14RC are emulated by the buttons on the RC 3TB see Table 4 6 K NET Termination Switch Terminates the K NET to RC 3TB daisy chain 7 K NET Connector Connects to either SL 14RC or additional RC 3TB 8 Front Panel For mounting the RC 3TB 9 Printed Circuit Board Contains the components of the RC 3TB 6 KRAMER SIMPLE CREATIVE TECHNOLOGY Defining the RC 3TB Remote Control Panel Optional Button 1 is always assigned to the second DISPLAY button button number 12 on the SL 14RC The position of the rotary switch see Table 4 determines which of the 12 buttons on the SL 14RC are emulated by buttons 2 and 3 on the RC 3TB Table 4 RC 3TB Rotary Switch Button Assignment Rotary Switch Button 1 Button 2 Button 3 Position
13. ement over the Ethernet port A K NET control channel that connects compatible user interfaces and supplies power and control data over a single cable Flexible control via Ethernet and K NET To achieve the best performance Use only good quality connection cables Position your Kramer SL 14RC away from moisture excessive sunlight and dust 1 Available from Kramer Electronics on our Web site at http www kramerelectronics com Defining the SL 14RC Master Controller 4 Defining the SL 14RC Master Controller Figure 1 and Table 1 define the front panel of the SL 14RC Master Controller SL 14RCG Figure 1 SL 14RC Master Controller Front Panel Table 1 SL 14RC Master Controller Front Panel Features Feature Function 1 IR Receiver Accepts IR control 2 ON LED Lights when the SL 14RC is switched on 3 Configurable Button Switches 1 10 Function is programmed by the K Config Configuration software 4 DISPLAY Configurable Button switches 11 and 12 Function is programmed by the K Config Configuration software 5 Rotary switch up down LED indicator Indicates the direction of travel of the rotary switch 6 VOLUME Rotary Switch Function is programmed by the K Config Configuration software 4 KRAMER SIMPLE CREATIVE TECHNOLOGY Defining the SL 14RC Master Controller Figure 2 and Table 2 define the rear panel of the SL 14RC Figure 2 SL 14RC Master Controller Rear Pane
14. gh the ear brackets Q CAUTION When installing on a 19 rack avoid hazards by taking care that 1 Itis located within the recommended environmental conditions as the operating ambient temperature of a closed or multi unit rack assembly may exceed the room ambient temperature 2 Once rack mounted enough air will still flow around the machine 2 Place the ears of the machine 3 The machine is placed straight in the correct against the rack rails and insert the horizontal position proper screws not provided 4 You do not overload the circuit s When through each of the four holes in connecting the machine to the supply circuit the rack ears overloading the circuits might have a detrimental Note effect on overcurrent protection and supply e In some models the front panel wiring Refer to the appropriate nameplate may feature built in rack ears ratings for information For example for fuse e Detachable rack ears can be replacement see the value printed on the ay hasan oer e inthe product label k bef ttach ble 5 The machine is earthed grounded ina Coa ine na oi the 5 reliable way and is connected only to an power electricity socket with grounding Pay particular jf you are using a Kramer rack attention to situations where electricity is adapter kit for a machine that is supplied indirectly when the power cord is not not 19 see the Rack Adapters plugged directly into the socket in the wall for user man
15. l Table 2 SL 14RC Master Controller Rear Panel Features Feature Function 1 K NET Connector Connect the GND pin to the Ground connection pin B and pin A are for RS 485 and the 12V pin is for powering the unit 2 SRVC Switch For service use only 3 K NET TERM Switch Slides down for K NET termination slides up for not terminated 4 FACTORY DEFAULT Button Press to reset to factory default definitions see Section 10 5 RS 232 Terminal Blocks Connect to the RS 232 devices from 1 to 6 6 RELAYS Terminal Blocks Connect to low voltage relay driven devices from 1 to 2 7 I O Terminal Block Connect to various analog and digital sensors 8 IR Output Terminal Blocks Connect to IR emitter cables from 1 to 2 9 ETHERNET RJ 45 Connector Connects to the PC or other serial controller through computer LAN 10 Mains Power Receptacle Connects to mains power 11 Mains Power Fuse Fuse holder for overload protection 12 Power ON OFF Switch Illuminated switch for turning the unit on and off 1 K NET is a proprietary Kramer protocol for interconnecting Kramer units 2 The ground connection is sometimes connected to the shield of the RS 485 cable in most applications it is not connected 3 First switch off the unit and then switch it on while pressing the DEFAULT button The unit powers up and loads its memory with the factory default definitions and erases all stor
16. on to the length of this warranty EXCLUSION OF DAMAGES The liability of Kramer for any effective products is limited to the repair or replacement of the product at our option Kramer shall not be liable for 1 Damage to other property caused by defects in this product damages based upon inconvenience loss of use of the product loss of time commercial loss or Any other damages whether incidental consequential or otherwise Some countries may not allow limitations on how long an implied warranty lasts and or do not allow the exclusion or limitation of incidental or consequential damages so the above limitations and exclusions may not apply to you N This warranty gives you specific legalrights and you may also have other rights which vary from place to place NOTE All products returned to Kramer for service must have prior approval This may be obtained from your dealer This equipment has been tested to determine compliance with the requirements of EN 50081 Electromagnetic compatibility EMC generic emission standard Part 1 Residential commercial and light industry EN 50082 Electromagnetic compatibility EMC generic immunity standard Part 1 Residential commercial and light industry environment CFR 47 FCC Rules and Regulations Part 15 Radio frequency devices Subpart B Unintentional radiators CAUTION amp Servicing the machines can only be done by an authorized Kramer technician Any user who
17. structions supplied with the product iii Repair or attempted repair by anyone not authorized by Kramer iv Any shipment of the product claims must be presented to the carrier v Removalor installation of the product vi Any other cause which does not relate to a product defect vii Cartons equipment enclosures cables or accessories used in conjunction with the product WHAT WE WILL PAY FOR AND WHAT WE WILLNOT PAY FOR We will pay labor and material expenses for covered items We will not pay for the following 1 Removal or installations charges 2 Costs of initial technical adjustments set up including adjustment of user controls or programming These costs are the responsibility of the Kramer dealer from whom the product was purchased 3 Shipping charges HOW YOU CAN GET WARRANTY SERVICE 1 To obtain service on you product you must take or ship it prepaid to any authorized Kramer service center 2 Whenever warranty service is required the original dated invoice or a copy must be presented as proof of warranty coverage and should be included in any shipment of the product Please also include in any mailing a contact name company address and a description of the problem s 3 For the name of the nearest Kramer authorized service center consult your authorized dealer LIMITATION OF IMPLIED WARRANTIES All implied warranties including warranties of merchantability and fitness for a particular purpose are limited in durati
18. ual for installation example when using an extension cable ora instructions you can download it power strip and that you use only the power from cord that is supplied with the machine http www kramerelectronics com 8 KRAMER SIMPLE CREATIVE TECHNOLOGY Connecting the SL 14RC Master Controller 7 Connecting the SL 14RC Master Controller To connect the SL 14RC as shown in the example in Figure 4 To RC 3TB Plasma Display RS 232 Projector Detector IR DVD Player IR S Lighting Power Amplifier Laptop running oo i System with Speakers Site CTRL Figure 4 Connecting the SL 14RC Master Controller 1 Connect the RELAY terminal block connectors as follows Connect RELAY to the lighting system z Connect RELAY 2 to the screen 2 Connect the I O port to a motion detector 3 Connect the IR outputs as follows 7 Connect an IR emitter to IR OUTPUT 1 and attach the emitter to the DVD player Connect an IR emitter to IR OUTPUT 2 and attach the emitter to the power amplifier 4 Connect the RS 232 ports see Section 7 3 as follows 1 Switch off the power on each device before connecting it to your SL 14RC After connecting your SL 14RC switch on its power and then switch on the power to each device 9 Connecting the SL 14RC Master Controller Connect RS 232 port 1 to the projector Connect RS 232 port 3 to the plasma display 5 Connect the Ethernet port to a network Connect th
Download Pdf Manuals
Related Search