easyRAID ER-M2S300+/B User manual
Contents
1. RAID 1 Hardware Installation Procedure 1 Connect the SATA cables on the removable hard drive carrier to the pins of hard drive 2 Secure the hard drive into the removable hard drive carrier by the screws which provided in the accessory pack Hardware Installation Procedure 5 Connecting ER M2S300 B to your computer 1 Connect DC12V amp 5V power cables and SATA cables to ER M2S300 B 2 Connect SATA cable to SATA port on the motherboard lol ies a SATA Cable Power Supply Connector p SS Power Supply e ER M2S300 B 45V GND 12v FAN Raid Raid1 CEFE re each plug is properly efore turning on the power 1 Motherboard E SATA Ports Real Panel Internal Case Note We do not recommend users to disassemble the machine without proper instructions and authorization The manufacture warranty will not cover damage caused by unauthorized disassembling Setting the Hard Drive Array Mode Please select the RAID mode with the jumper located at the back panel The original default is RAID 1 still there are three pins at the back panel for RAID mode selection RAID 0 mode by setting the jumper on the left of the two pins RAID 1 mode by setting the jumper on the right of the two pins 1 RAID 0 Mode 1 Place two new hard drives in2. B Since one of the slots is empty the buzzer will alarm user about the empty slot when the computer is turned on To shut off the buzzer alarm just push the bottom located in the front display screen After turning on the operation system please check whether the current ER M2S300 B setting is the same prior to hard drive installation Then place the new hard drive in the removable hard drive carrier into another slot Note the storage capacity of the newly installed hard drive must be larger than or equal to the old hard drive The ER M2S300 B will start the auto rebuilding function shortly after Please press the Buzzer bottom after auto rebuilding to reset the buzzer alarm and to return the system operation normally If you use this install method and backup OS at the same time please make sure that the system is installed normally in case of error or OS backup failure OS Backup 7 Computer Set Up When the hardware setup for ER M2S300 B is complete you are now ready to turn the machine on 1 After the hardware installation is complete the ER M2S300 B will be treated as one single hard drive Set the hard drive to AUTO in the computer s BIOS When the computer is turned on the system will retrieve the following information 2 In ER M2S300 B the installed hard drive can be detected by the Device Manager of Computer Management for Windows 3 Customers can choose to format the hard drive by u
3. 2S300 B is Buzzer On 2 The user can use any pointed materials to push the bottom on the front dash board
4. al A Please first check whether the ER M2S300 B is in the progress of executing data auto rebuild 1 Please examine if the length of the connection cables SATA cable that connect the drives to the computer system is too long and whether the specification these cables complies with the requirements 2 If both the lengths and specification of the cables are checked out ok please turn off ER M2S300 B and remove the hard drive from it Test the hard drive directly with the computer system since it might be the bad sectors in the hard drive that are causing the longer than normal system down time Hard Drive Failure Q Under the mirror mode RAID 1 what will be the system s total storage capacity when adding a brand new hard drive A 1 The total storage capacity for ER M2S300 B is determined by the storage capacity of the primary hard drive installed during the initial usage 2 The storage capacity will not increase after initial installation even when place a brand new hard drive with larger storage capacity Q Why does the error message appear when installed the second hard drive A 1 The storage capacity of the second hard drive must be larger than the first hard drive Otherwise ER M2S300 B can not rebuild the new hard drive and the LCD display screen will display Wrong Capacity 2 The LCD display screen might display rebuilding error messages such as Pri s gt Sec s or Sec s gt Pri s The term s signifies that
5. both hard drives are treated as original hard drive The user must determine which hard drive will be the original hard drive prior installing the hard drives into ER M2S300 B Once the original hard drive is designated and installed in ER M2S300 B the user can place in the second hard drive by taking advantage of ER M2S300 B s Auto Rebuilding function Q My hard drive is obviously operating properly but why is it shown as failed in the ER M2S300 B display A ER M2S300 B uses more strict requirements and standards to examine the bad sectors in the hard drive The user can first overwrite the bad sector on a PC before placing the hard drive into ER M2S300 B Appendix Trouble Shooting Q amp A 11 About Auto Rebuilding Function Q What will happen if we turn off the computer s power while ER M2S300 B is still executing data A auto rebuilding Under the mirror mode RAID 1 if the power is out of the auto rebuilding process the controller will remember when completion percentage of the auto rebuilding process and resume the rebuilding process when the power is back on Is it possible to lose any part of the data during the data auto rebuilding The data auto rebuilding function will copy data from one sector to another sector Technically speaking the data will not be lost during the auto rebuilding process However if the original hard drive is detected with bad sectors during the rebuilding process ER M2S300 B w
6. easyRAID ER M2S300 B User Manual Version 3 2 March 2010 http www easyRAID com Check Package Contents and Accessories Hardware Introduction Index System Requirement amp Environment Requirement and Notices 000 Hardware Installation Procure cccccceceeeeeeeeeeeecceeceeeeeeeeeeeseeseesacsasaeeeeeees Connecting ER M2S300 B to your computer Setting the Hard Drive Array MdG secissarsoncninicend eee a OS BaCk P mietoa nnna Computer Set Up 0 0005 Hard Disk status on LCD screen Appendix Trouble Shooting Q amp A Check Package Contents and Accessories ER M2S300 B system includes the following Item ER M2S300 B Removable Carrier SATA Cable Product CD Accessory bag includes 6 32 screws x 8 pcs Key for keylock x 2 ER M2S300 B HS oe SATA Cable gt Le a 1 1 1 1 Accessory bag Product CD Note Please check above parts are included prior to installation The accessory bag contains screws and a plastic key Check Package Contents and Accessories 3 Hardware Introduction Front Panel Real Panel jo 45V GND 12v FAN Raido Raid ob WIM a EFC e olo o o 4 LCD Panel 2 HDD Tray 4 SATA Port 2 Power Socket 3 Mute Button 4 Key Lock 3 RAID Mode 4 5cm Fan 5 HDD Access LED 6 Fail LED Note Stat
7. ill make hypothetical duplication instead of treat the bad sectors as hard drive failure Therefore the data stored in the bad sectors could potentially be lost during rebuilding Under the mirror mode RAID 1 why does the computer slows down during the data rebuilding process Or why does the data rebuilding process slows down when the data is being processed If the ER M2S300 B system is executing data rebuilding simultaneously while the computer system is saving the data the auto rebuilding process and the saving process will take longer than normal time This is because the ER M2S300 B must divide it s resource between the normal system operation and the data rebuilding process However the priority for the ER M2S300 B is to maintain the proper system operations Therefore the data rebuilding speed will be extremely slow until the system finished with the data saving operations Other Possible Situations Q The Buzzer will not stop when the ER M2S300 B is in operation A Please check whether the readings on the LCD display are normal or if there is a hard drive failure Please also pay attention to any other symbols displayed in the LCD display For example if the F symbol is displayed this means that there is a cooling fan failure If the T symbol is displayed this means that the system is overheated Q How to turn on and off the Buzzer A 1 The manufacture default setting for the Buzzer in ER M
8. protect the system from being hit by computer virus or to avoid risk of having both hard drives failing at the same time 2 During the Hard drive Failure When one of the two hard drives fails in the ER M2S300 B system the system will alarm the hard drive failure message both on the LCD display screen and in the monitoring software The user can remove the failed hard drive from the system while the system is still in operation without shutting down the machine If the failed hard drive is replaced shortly the system will automatically execute the Auto Rebuilding function without affecting the system operation and without any operation command from the user 3 The LCD Display Message During Hot Swap and Auto Rebuilding When the ER M2S300 B detects a hard drive missing or a hard drive failure the Buzzer will go off and the LCD display screen will display the following messages Hard Disk status on LCD screen 9 PriHDD OK Pri HDD Failed Sec HDD Failed Sec HDD OK 4 After removing the failed hard drive and replacing with a new hard drive if the hard drive is properly installed the LCD display screen will display the following messages Pri HDD OK Sec HDD OK 5 After few seconds of installing the new hard drive the LCD display screen will display the data rebuilding progress Rebuilding Rebuilding Pri gt Sec XXX Sec gt Pri XXX Pri gt Sec represents that the data in the original hard drive p
9. rimary hard drive is copied to the new hard drive secondary hard drive XXX represents the rebuilding completion percentage 6 When the rebuilding is fully completed the LCD display screen will again display the following messages Pri HDD OK Sec HDD OK 7 When ER M2S300 B is overheating T will be displayed on the lower right hand corner of screen As shown in illustration Pri HDD OK Sec HDD OK T 8 When cooling fan module is not functional F will be displayed on the upper right hand corner of screen As shown in illustration Pri HDD OK F Sec HDD OK 10 Hard Disk status on LCD screen Appendix Trouble Shooting Q amp A Unstable system after connecting ER M2S300 B Q After installing ER M2S300 B we are unable to start the computer or the computer can not locate ER M2S300 B upon startup A 1 Please check whether the readings on the ER M2S300 B LCD display screen appear normal 2 Please check whether the SATA Cable connection cables are properly connected to the computer system and whether SATA drives are functioning normally 3 If everything is functioning properly but the user still can not start the computer system then the problem might be the system incompatibility If such incompatibility takes place please contact our technical support department Q When the ER M2S300 B is in use the computer system is functioning normally but the ER M2S300 B access speed is abnorm
10. sing the Disk Management tool of the operating system before using the ER M2S300 B Tenar ah e on e Bxesae Weathy System PET naD w No EDD Patton Ra NTFS Hesthy Boot 7 97GR 515GB No MSS MAG 9 No At this point the installation process is completely finished The user can freely retrieve and save data to ER M2S300 B just like retrieving and saving data to a regular hard drive If the user experiences any abnormality during the operation please refer to the trouble shooting Q amp A section in Appendix 8 Computer Set Up Hard Disk status on LCD screen Left Hard Drive Primary Hard Drive Fail 1 Right Hard Drive Secondary Hard Drive Normal Pri HDD Failed Sec HDD OK 2 Primary hard drive storage capacity larger than secondary hard drive Wrong Capacity PRI gt SEC 3 Secondary hard drive storage capacity larger than primary hard drive Wrong Capacity SEC gt PRI Hot Swap amp Auto Rebuilding The hard drive Hot Swap and Auto Rebuilding functions are available The Hot Swap amp Auto Rebuilding functions are applicable in 1 Off line Back up When the data is stored within ER M2S300 B the user can remove one of the hard drives from ER M2S300 B as back up drive for data such as system operation file secured files seldom modified files or image and music files The user can periodically insert the hard drive back into ER M2S300 B to execute automatic backup to
11. to ER M2S300 B and strongly suggest you to use two identical hard drives to get the equal capacity If the capacity is different ER M2S300 B is downward to the small hard drive capacity 2 Under RAID 0 mode capacity is add up to a one big volume also with the feature of faster read write performance efficient 6 Connecting ER M2S300 B to your computer Setting the Hard Drive Array Mode 2 RAID 1 Mode 1 Place two new hard drives into ER M2S300 B and strongly suggest you to use two identical hard drives to get the equal capacity If the capacity is different ER M2S300 B is downward to the small hard drive capacity 2 Under RAID 1 mode two hard drives has the identical information as one to mirror to the other one therefore each of the hard drive failed is still able to function normally When you replace the failed hard disk to the new one the system automatically rebuilding the data to the newly place hard disk OS Backup Installing a brand new hard drive and a hard drive with existing data Internal RAID module is suggested to be used for OS backup data fi We highly recommend using the same brand of hard drives with the same or larger storage capacity when installing hard drives to ER M2S300 B The user can use the auto rebuilding function to automatically format the new drive and subsequently to back up the data into the new hard drive Place the hard drive with existing data into slot 1 or 2 in the ER M2S300
12. us Indications of LEDs HDD Access LED will flash yellow when the data is accessed from the hard drive Fail LED will light red when HD failed temperature is higher than 60 C or fan fails System Requirement amp Environment requirement and notices Hardware Requirement 1 Computers or servers with SATA amp SATA II 2 Hard drive with SATA amp SATA II Environment requirement and notices 1 ER M2S300 B brilliant design allows the user to simultaneously utilize two hard drives manu factured by different companies However if the user expects better efficiency we strongly recommend the users to use hard drives manufactured by the same manufacturer 2 Since the system uses more stringent factors to determine the disk corruption in the hard drive please use noncorrupted hard drive with minimum storage capacity of 20 GB 3 The ER M2S300 B had undergone strict hard drive compatibility test The result shows that it is compatible with most hard drives on the market such as Maxtor Western Digital Seagate Fujitsu Hitachi and etc 4 Hardware Introduction System Requirement amp Environment requirement and notices 4 The ER M2S300 B is equipped with a 5 2 cm ball bearing cooling fan that will provide effective cooling for the 7200 amp 10000 rpm hard drive We highly recommend using computer chassis with effective cooling design to avoid disk array crashing due to ineffective cooling 5 ER M2S300 B supports RAID 0 amp
Download Pdf Manuals
Related Search