STE03-B User Manual
Contents
1. at the end of operations it will display the window shown in figure 5 1 Device ready Fig 5 Configuration completed NOTE You can not configure devices with not supported software versions MORE INFORMATION The Quit and buttons are used respectively to close the application and to display information on the software version2. selected device as shown in figure 4 NETWORK CONFIGURATION IP P address of device configurable values range from 0 0 0 1 to 223 255 255 255 Subnet Subnet Mask of device valid values greater than 254 255 255 255 Gateway IP address of gateway if there is no gateway set to 0 0 0 0 Use DHCP if selected active IP address assignment from DHCP Server Do not enable this option unless you are sure that the network has a DHCP Server MODE Auto 10Mbit 100Mbit set Ethernet Speed ING Hardware amp Software Engineering ADVANCED CONFIGURATION TCP PORT is the gate of the TCP IP protocol on which the communication takes place with the serial port of the device Valid values are between 1 and 65535 E E ioj x Network configuration Serial port parameters IP 192 168 100 100 pperepsepraepearere versus WE BaudRate 19200 gt Subnet 255 255 255 0 Parity None gt Gateway 0 0 0 0 Databit g UseDHCP T Stopbit ji Mo de _ C Auto C 10Mbit 100 Mbit Sending condition MG STE Configurator MAC Address _ Device Ver Advanced configuration Time o 10ms ient mode acivation F Dim 1 964 TCP Port 5000 165535 Char oo Hex End condition _ Device F ede idle time O sec Description Eh Configure Fig 4 Parameters visualizatio
3. Serial to Ethernet Converter STE03 B User Manual Ver 1 2 ING Hardware amp Software Engineering DECLARATION OF COMPLIANCE With the present MG S r l declares that the product STEO3 is in compliance with the essential requirements and other relevant provisions of Directive 1999 05 EC with reference to the following regulatory standards EN55022 EN55024 EN61000 3 2 EN60950 INTRODUCTION The contents of this manual may change without notice MG S r l assumes no responsibility for errors and or omissions technicians TECHNICAL CHARACTERISTICS SUPPORTED PROTOCOLS TCP UDP IP ARP ICMP DHCP Server operating mode NETWORK ETHERNET CONNECTION Auto sensing 10 100 Mbps on RJ45 SERIAL PORT 1 asynchronous TTL serial port 3 3 V on 2 54 pitch strip connector Speed from 1200 to 115200 bps Signals TXD RXD Data format 8 bits parity None Even Odd 1 stop bit OTHER FEATURES Power Supply 5 Vdc Consumption 0 6 W 10 Mbit 1 3 W 100 Mbit LED link activity Operating temperature 20 60 Humidity 5 90 not condensing Dimensions 70x17x45 LxHxW 1 5 KV insulation on Ethernet RoHS ING Hardware amp Software Engineering COLLEGAMENTI SERIAL TTL AND POWER SUPPLY RJ45 LAN CONNECTOR J3 CONNECTOR 1 GND 2 TX module output 3 RX module input 4 5 Vdc Power can be supplied either from J4 conne
4. ctor or J3 connector pins 1 4 ING Hardware amp Software Engineering SOFTWARE INSTALLATION To configure the device easily you can use the installation wizard This procedure allows you to install and run STECfg that allows you to automatically detect STEO3 devices in the network which are linked and initialize the main parameters for its proper functioning as well fe Setup STEOS Management e iiol Welcome to the STE03 Management Setup Wizard This will install STEOS Management Ver 1 3 on your computer It is recommended that you close all other applications before continuing Glick Next to continue or Cancel to ext Setup Fig 1 Installation procedure Welcome Page To install the application you simply open the file setup exe on the provided CD and follow the installation wizard After this procedure you can blaunch STECfg from Start Programs STE03 folder or from the directory where you chose to install the program After installation you can launch the application by selecting the option shown in Figure 2 iG Setup STEO3 Management lel es Completing the STEO3 Management Setup Wizard Setup has tinished installing STEO3S Management on your computer The application may be launched by selecting the installed icons Click Finish to ext Setup Fig 2 Setup Setup completed ING Hardware amp Software Engineering USING STECfg INTRODUCTION STECfg is the con
5. figuration program that allows the user to configure the serial port and the network parameters of the STEO3 module The program consists of a single window that contains inside it all the options and configurable parameters the fields have been grouped by topic and then divided into main categories When you start the program it appears as in figure 3 F MG STE Configurator Network configuration Serial port parameters MAC Address IP ai cde 8 BaudRate 9600 z Subnet g 7 0 i 0 a 0 Parity None ha Gateway 0 0 0 0 Data bit a Use DHCP T Stop bit fi Mage e Auto Jo Mbt E Loo Mbit Sending condition Advanced configuration _ Time o 10ms Gient made activation F Dim o 1 964 TCP Port 0 ti 65535 Char o0 Hex Lift oor m m e m 0 0 1 Serre Dyart i i AS al Device Se l Description F i ic End condition Idle time 0 sec Fig 3 Main Window LOOK FOR DEVICES To search for STEO3 devices on the network press the search button After the search the list of detected devices will appear in the main window its MAC address product name and version If any device is not detected on the network you will see a warning message EDITING OF PARAMETERS Then simply select a device to change its parameters when you select a device from the list all the fields on the window are filled with the current values of the
6. n SERIAL PORT PARAMETERS Speed serial port speed Parity parity of the serial port None disabled Even Odd Dat Bit default 8 Stop Bit default 1 SENDING CONDITION The conditions are applied to incoming data from Serial Port then outgoing on the LAN Time is the time expressed in 1 100 of sec since the last data received on the serial port after which the data is actually sent on the LAN Valid values range from 0 to 9999 If this parameter is greater than O you will also need to set Dim field but if it is O the option is disabled Dim you can choose between 0 and 964 the number of bytes to receive before sending As in the previous field if the value is 0 the option is disabled and the received data are immediately sent Char hexadecimal value that represents the data to send it can assume any value if it is set to zero it is disabled If not zero the device stores the data and sends them when this character is received the byte is also sent In this case you must specify a value of Dim END CONDITION Idle Time value expressed in seconds after which the TCP connection is closed The timeout is reset every received data ING Hardware amp Software Engineering SEND THE CONFIGURATION After selecting a device and changing the fields with the desired values simply press the Configure button to send all the parameters If the parameters are accepted the device reboots and
Download Pdf Manuals
Related Search