user manual - THE MR FANTASTIC PUMPING PENIS
Contents
1. the battery charging must be done exclusively when the device is not in use The battery must be charged when necessary do not charge the battery continually if it is not out of power for about 70 80 or there will be the risk of nullifying its duration Static pumping The device has been designed for dynamic pumping It has a natural slow vacuum leak that is amplified and regulated by the controlled loss valve If you wish to use the device for static pumping you have to remember that is does not maintain a constant vacuum but will always tend to slowly lose vacuum Possible causes of malfunctions The most important thing for a correct operation of the pump is to be sure to have the well sealed vacuum circuit If during the session you realize that the vacuum does not reach the predetermined value that the pump does not suck or not suck enough the thing to do are the following 1 be sure that the battery is charged if the LED is red it means that the device must be recharged with little power due to low battery the display may be switched on but does not have enough power to run the pump so suitable 2 holding the pump on disconnect and reconnect all the connectors push energy and make sure they are properly engaged after inserting it to make a half turn to the right and left 3 verify that the valve knob is screwed loss that is closed if you get the knob open after filling the cylinder obviously in the circuit water will2. vacuum of 9 0 set the minimum value N 1 at 4 0 and set H I value at 5 0 Cycles at a minimum vacuum of 3 3 and maximum vacuum of 10 2 set N I to 3 3 set H I to 6 9 cycles at a minimum vacuum of 4 5 maximum vacuum of 8 7 set N_I 4 5 and H_I to 4 2 cycles at a minimum vacuum 5 5 maximum vacuum 11 0 set N I to 5 5 and H I to 5 5 Note If you have 4 0 as minimum value and 8 0 as maximum value when you modify only the value N_I that is 4 0 and you bring it to 5 0 for example you will obviously increase the maximum value H I too so it will automatically become 9 0 so you will have 5 0 as minimum value and 9 0 as maximum value It might seem complicated but once you become familiar with the device it will become quite easy because if used correctly usually you will only change the maximum value while you will almost always have the same minimum value ie you will normally only modify the H_I value You are advised to adjust minimum and maximum values by following this handbook exclusively without relying on any other menu option but if you unconfigure the menu in error with the buttons under the display contact mrfantasticpumping hotmail it we will help you with reprogramming Lithium ion battery The dual power supply version of the device includes a lithium ion battery a very powerful and safe new generation battery that can supply the device for some hours with a range of at least two full hours
3. T PUMP Water connectors CONNECTOR CONNECOTR The pump has two connectors right and left The right is the discharge connector and must therefore be connected to the connector on the left of Final discharge unit 1 DISCHARGE 4 CONNECTOR i 5 LEAK VALVE CONNECTOR CO NNECTED TO CYLINDER The left connector of the pump must be connected to the cylinder connector 1 CONNECTOR 2 The scheme described above should be followed as pictured The discharge connector is important do not invert it If it is inverted the pump will not generate any vacuum but there are not obviously dangers or damage to the device Final discharge unit The final discharge unit must be completely immersed about 6 cm in water during operation of the pump It must be connected the discharge tube and the tube connected to the controlled loss valve Controlled loss valve The valve is positioned on the final discharge unit during use of the pump must be completely immersed in water The white knob on the head of the valve controls the rate of descent of the vacuum You have to adjust it by gently tightening or loosening 1 or 2 mm at a time so finding the right setting at your leisure Valve adjustments should be made keeping it totally immersed in water If you fully tighten clockwise there would be no leak and the vacuum level would remain stable Regulation intensity knob The intensity control knob above is a current regulator that
4. USER MANUAL ELECTRIC DYNAMIC PUMP This manual briefly explains the operation of the device The points described below are the on off button the current switch power and charging connectors water connectors final discharge unit controlled loss valve regulation intensity knob display battery charge indicator supplied cylinder and the filling and emptying operation the connection tubes and how best to use the device and set vacuum values The on off button The on off button turn the device on and off In I position the device is in operation in O position the device is off The switch As in the figure above the switch selects the type of power supply only for the dual power supplymodel A C batteries with AC batteries or power supply The switch positioned on the left black color uses a battery supply device The switch positioned on the right operates the device with AC mains power via a transformer To use the battery keep the selector positioned on the left To use AC power keep the switch positioned to the right In order to recharge the battery keep the switch positioned to the left If while using the battery powered device the switch is moved to the right the device will lose power and stop The left connector is only used to recharge the battery while the device is not in use The right connector is for AC power supply and should only be used to supply the device while it is in use LEFT PUMP RIGH
5. circulate freely without reaching any vacuum if so then close screw the valve knob loss located on the end of the drain 4 Ifthe cylinder are continuous and large bubbles of air means that there is a leak in the vacuum circuit check that the silicone ring is tightly around the base of the penis in some cases it may be necessary to depilation 1f not total at least partial ie shorten the pubic hair to prevent it from entering three ring silicone and the base of the penis by creating mini leaks 5 Ifafter doing all the above steps the pump does not yet reach the vacuum preset or it hardly reaches check all the male and female connectors and make sure there are no hairs stuck inside even just a hair happened in the connector can be a cause of loss 6 Finally check that there is something blocking the water flow in the circuit how to do take the final unloading connect a hose to the connector on the right and blow energy on the other end of the pipe if it is clogged check that there is something or inside the tube or in the connector of the final exhaust if it is free to do exactly the same operation with the connector on the left and with all three of the tubes the tubes and the final unloading must be not obviously clogged 7 Connect a hose to the connector on the right and one to the left connector of the pump dip in the water pipe connected to the left connector of the pump and turn on the device giving full power If the pump runs y
6. on tubes How best to use it In this section we will explain in a few essential points and most important how to use the device 1 Rest the device on a flat surface near the water source connect final discharge unit to the pump the right connector of the pump into the left connector of the final discharge unit the left connector of the pump into the cylinder connector 1 the left connector of final dischage unit into the cylinder connecot 2 completely immerse the final discharge unit in water 2 Wear the cylinder on the pump and with the knob give maximum power to fill the cylinder open completely unscrew the leak valve lacaetd on the top of final discharge unit 3 When the cylinder is almost full of water point it out As soon it is completely full of water and without air bubbles inside close screw the leak valve and the vacuum reaches the value preset The position of the cylinder must be with the tip pointing upwards during filling as the photo below WE STRONGLY RECOMMEND USING WARM WATER IN THIS PUMP Hi Warmth assists in achieving the BENEFITS this device is capable of AND PREVENTION of injuries that can result from excessive pumping eg red spots Setting vacuum values The device is equipped with three buttons from which you can regulate the minimum and maximum vacuum which can be set in two different ways Setting minimum vacuum N D 1 To set minimum vacuum turn on the device by turning the p
7. ou will notice that the tube immersed in water vienere sucked water from the hose and water comes out right it means that the pump works well Water filter The device has an internal water filter to prevent debris or hair entering the vacuum pump and affecting its correct operation I cannot predict when it needs to be cleaned or replaced because it depends on the type of use and the cleanliness of the water used but if in case you have a malfunction and you ve already made all the steps described in Possible causes of malfunctions and reset the display as described in the last paragraph of this manual you can sufficient to clean or replace the filter with the spare you have been given On the underside of the device there is a small opening fixed elesed with 2 screws Unscrew the 2 screws and the small cover will come off and you will be able to see the filter which is connected to a tube as in the following picture Gently pull the filter out and disconnected by simply pulling tubes but with the other hand holding the hose either clean the filter or replace it with this new filter tuck inside as it was before and close by tightening the 2 screws To clean the filter just soak it in hot water blow in goth ends to remove any obstructions When you get good air flow refit it to the pump Checking pump settings 1 Turn on the device 2 Turn the black knob fully counterclockwise 3 Press the central S button for 3 4 second
8. ower switch on I position The display will show 0 1 0 2 2 now press the central button once You will display the flashing writing N_I present value 3 Press the button on the right to decrease or press the button on the left to increase 4 press the central button once more and you have finished setting minimum vacuum For example use the side left and right buttons to set 3 7 Hg So the value 3 7 Hg that you have just set means that when vacuum arrives to 3 7 the device starts and leads the vacuum to the maximum preset value the vacuum inside the vacuum circuit will not decrease under 3 7 To set the maximum vacuum value vacuum that the device will reach you set a number H 1 H I represents the increase in vacuum from the minimum set vacuum N T ie Maximum set vacuum N I H I Setting H I 1 Turn on the device by pressing I the display will show 0 1 0 2 hold down the central button for at least 3 seconds the display will show the writing F 0 2 pressthe left button once the display will show the writing F 1 3 Now press the central button four times until the display shows the writing H I You increase with the button on the left and decrease with that on the right 4 then press again the central button for at least 3 seconds the display will show the writing 0 1 0 2 and you have now set the maximum value Examples If you want to make cycles at a minimum vacuum of 4 0 and a maximum
9. regulates the speed and the noise level of the device It must be used gently The intensity increases by turning it clockwise The intensity decreases by turning it anti clockwise If you turn the knob completely anti clockwise you remove power to the device and it stops This is normal The knob regulates the speed of vacuum increase and also the noise though moderate that the device emits Applying more power to the vacuum pump draws out air more guickly from the vacuum circuit clockwise Applying less power to the vacuum pump draws out air more slowly anti clockwise The display From the display you can display the vacuum value inside the circuit When the vacuum pump is active the numbers will be displayed in red When the pump is not active the numbers will displayed in green When the device starts the display flashes for some seconds about 2 seconds and it starts at the values that have been set previously The display shows the vacuum inside the vacuum circuit in inches of Hg they can also be displayed in Bar Psi etc Without having closed the vacuum circuit by connecting the small tube the display will show 0 1 0 2 that is normal since there is no vacuum Led indicator battery charge level When it is green the charge is about 100 when is Yellow indicates a charge from 80 to 30 When is red indicates a charge under 30 and then you have to recharge before the next use of the device Description connecti
10. s and arrive in F O 4 Press center S button one time and ensure the settings for uni is inH if not press up or down arrows to change the value 5 Press center S button one time arrive at F 0 6 Press left up button one time and arriveat F 1 7 Press center S button one time and ensure the setting for oUI is HYS if not press up or down arrows to change the value 8 Press center S button one time and ensure the setting for lot is I_n if not press up or down arrows to change the value 9 Press center S button one time and ensure the setting for n_I 1s 3 your minimum vacuum if not press up or down arrows to change the value 10 Press center S button one time and ensure the setting for H 1 is 7 your maximum vacuum if not press up or down arrows to change the value 11 Press center S button one time and ensure the setting for Col is Sor if not press up or down arrows to change the value 12 Press center S button one time and arrive at F 1 and settings is complete 13 Press and hold center S button for 3 4 seconds to arrive at vacuum display Ensure the display is red and the value is 0 0 0 1 and screw black knob clockwise to desired pumping speed
Download Pdf Manuals
Related Search